This document presents a proposed photovoltaic system with MPPT and a Zeta converter to improve efficiency. The system aims to maximize solar panel power output using an MPPT technique and regulate the output voltage with a Zeta converter. The Zeta converter is chosen because it maintains the same polarity for both voltage and current compared to other converters. The proposed system is simulated in MATLAB Simulink and results show that it reduces voltage and current ripple at the output compared to an open loop system without MPPT or converter regulation. The system improves efficiency by tracking maximum power from the solar panels and maintaining a regulated output voltage with low losses.
This paper presents a maximum power point (MPP) tracking method based on a hybrid combination between the fuzzy logic controller (FLC) and the conventional Perturb-and-Observe (P&O) method. The proposed algorithm utilizes the FLC to initialize P&O algorithm with an initial duty cycle. MATLAB/Simulink models consisting of, the photovoltaic system, boost converter and controllers, are built to evaluate the performance of the proposed algorithm. To accurately illustrate the performance of the proposed algorithm, comparisons with standalone FLC and P&O are carried out. The performance of the proposed algorithm is investigated difficult weather conditions including sudden changes and partial shading. The results showed that the proposed algorithm successfully reaches MPP in all scenarios.
Integral sliding-mode controller for maximum power point tracking in the grid...IJECEIAES
The output power generated in the photovoltaic modules depends both on the solar radiation and the temperature of the solar cells. To maximize the efficiency of the system, it is required to monitor the maximum power point of the photovoltaic system. For this purpose, monitoring the maximum power point (MPPT) of photovoltaic systems should be as quick and accurately as possible for increasing energy production, which ultimately increases the cost-efficiency of the photovoltaic system. This paper proposes a new approach for MPPT) using the concept of the integral sliding mode controller (ISMC) to ensure fast and precise monitoring of the peak power. The performance of the ISMC is significantly influenced by the choice of the sliding surface. To assess the reliability ISMC control, the results have been compared with those of a PI controller. The results obtained are used to evaluate the performance of the ISMC strategy under different climatic conditions. Finally, the effectiveness of the proposed solution is confirmed using simulations in PSIM tools and experimental results were used to evaluate the effectiveness of the proposed approach.
A SIMSCAPE based design of a dual maximum power point tracker of a stand-alon...IJECEIAES
This paper presents the simulation of a dual maximum power point tracker (dual-MPPT) and attempt to get the global maximum power point GMPP under partial shading conditions for a solar photovoltaic module using MATLAB SIMSCAPE. Traditional single MPP trackers are less efficient than dual MPP trackers and have greater sensitivity to partial shading. By using dual MPP trackers, one can get several features such as the possibility of connecting two arrays with different string sizes or different solar azimuths or tilts within high efficiency. This paper focuses on making the photovoltaic system work at maximum possible power under partial shading condition by using dual MPP trackers to achieve the convergence toward the global maximum power point GMPP.
This paper presents a maximum power point (MPP) tracking method based on a hybrid combination between the fuzzy logic controller (FLC) and the conventional Perturb-and-Observe (P&O) method. The proposed algorithm utilizes the FLC to initialize P&O algorithm with an initial duty cycle. MATLAB/Simulink models consisting of, the photovoltaic system, boost converter and controllers, are built to evaluate the performance of the proposed algorithm. To accurately illustrate the performance of the proposed algorithm, comparisons with standalone FLC and P&O are carried out. The performance of the proposed algorithm is investigated difficult weather conditions including sudden changes and partial shading. The results showed that the proposed algorithm successfully reaches MPP in all scenarios.
Integral sliding-mode controller for maximum power point tracking in the grid...IJECEIAES
The output power generated in the photovoltaic modules depends both on the solar radiation and the temperature of the solar cells. To maximize the efficiency of the system, it is required to monitor the maximum power point of the photovoltaic system. For this purpose, monitoring the maximum power point (MPPT) of photovoltaic systems should be as quick and accurately as possible for increasing energy production, which ultimately increases the cost-efficiency of the photovoltaic system. This paper proposes a new approach for MPPT) using the concept of the integral sliding mode controller (ISMC) to ensure fast and precise monitoring of the peak power. The performance of the ISMC is significantly influenced by the choice of the sliding surface. To assess the reliability ISMC control, the results have been compared with those of a PI controller. The results obtained are used to evaluate the performance of the ISMC strategy under different climatic conditions. Finally, the effectiveness of the proposed solution is confirmed using simulations in PSIM tools and experimental results were used to evaluate the effectiveness of the proposed approach.
A SIMSCAPE based design of a dual maximum power point tracker of a stand-alon...IJECEIAES
This paper presents the simulation of a dual maximum power point tracker (dual-MPPT) and attempt to get the global maximum power point GMPP under partial shading conditions for a solar photovoltaic module using MATLAB SIMSCAPE. Traditional single MPP trackers are less efficient than dual MPP trackers and have greater sensitivity to partial shading. By using dual MPP trackers, one can get several features such as the possibility of connecting two arrays with different string sizes or different solar azimuths or tilts within high efficiency. This paper focuses on making the photovoltaic system work at maximum possible power under partial shading condition by using dual MPP trackers to achieve the convergence toward the global maximum power point GMPP.
Hey Guys,
This Project we made it for final year Engineering students and for well knowledge. It was an amazing experience when we made it successfully.
If you want this project then contact :
Kalpesh Badgujar - 8879254715
if any query about this project mail :
badgujarkalpesh201@gmail.com
Its a comparison of performance of MPPT controllers in case of solar PV array under same working conditions. The MPPT controllers used are Artificial Neural Network and P&O based.
Enhanced MPPT Technique For DC-DC Luo Converter Using Model Predictive Contro...IJERD Editor
The present study explored an enhanced maximum power point tracking technique which ensures fast tracking in PV systems. This system represents a Model Predictive Control (MPC) MPPT technique. Extracting the maximum power from PV systems has been widely investigated. The main benefaction of this article is an improvement of the Perturb and Observe (P&O) method through a fixed step predictive control under measured fast solar radiation. The preferred predictive control to achieve Maximum Power Point (MPP) speeds up the control loop since it predicts error before the switching signal is applied to the DC-DC Luo converter. Comparing the improved technique to the conventional P&O method indicates significant improvement in PV system performance. The proposed MPC-MPPT technique for a Luo converter is implemented using the MAT LAB SIMULINK
An Improved Constant Voltage Based MPPT Technique for PMDC MotorIAES-IJPEDS
Stand-alone photovoltaic (SAPV) systems are being used in remote areas
and are being seen as one of the promising solution in this regard. The SAPV
system as presented in the paper consists of solar PV panel, a DC-DC
converter, a controller and a PMDC motor. The current-voltage and powervoltage
characteristics being nonlinear, the SAPV system require maximum
power point techniques (MPPT) control techniques to extract maximum
power available from the PV cell. A voltage based MPPT technique which is
capable of tracking MPP has been selected because of numerous advantages
it offers such as: simple and low cost of implementation. The limitation of
constant voltage method is that its efficiency is low as the PV panel has to be
disconnected from the load for measurement of the open circuit voltage
(Voc). In the presented paper, the authors have removed this limitation by
using a pilot PV panel for measurement of Voc. A proportional-integrator (PI)
based controller is used in implementation of constant voltage MPP
technique and the modeling is done in MATLAB®/SIMULINK simulation
environment. The simulation results are presented and discussed in the paper,
the results shows that the efficiency of the system has increased.
Development of a Novel Robust Differential Maximum Power Point Tracking (MPPT...IJSRP Journal
The use of photovoltaic (PV) systems is increasingly growing in importance since they involve an exploitation of solar radiation constituting an energy source which is renewable, available in most places, and pollution-free. Despite their numerous advantages, PV systems have two major drawbacks: low energy conversion efficiency and loss of energy due to variations in meteorological conditions; for this reason, Maximum Power Point Tracking (MPPT) control techniques play a key role in exploiting the maximum energy caught by PV modules. The output characteristic of a photovoltaic array is nonlinear and changes with solar irradiation and the cell’s temperature. Therefore, a Maximum Power Point Tracking (MPPT) technique is needed to draw peak power from the solar array to maximize the produced energy. In this study we have analyzed the Maximum Power Point Tracking (MPPT) method and finding out a new and easier way to track maximum power point (MPP) and also our study is focused to overcome the drawbacks of MPPT. This research paper presents a novel MPP tracking method for tracking exact Maximum Power Point (MPP) if the irradiation or load changes.
Fuzzy logic based MPPT technique for a single phase Grid connected PV system ...THOKALA SOWMYA
In the proposed paper power generation from photovoltaic array is used to connect the grid. DFCM
Inverter control with PSPWM technique is used in order to control active and reactive power injected into grid. FLC
MPPT technique is proposed for maximum power point tracking and is compared with Constant voltage MPPT
technique. The simulation results of proposed system and Constant voltage MPPT technique are compared by using
MATLAB/SIMULINK software.
Maximum power point tracking of pv arrays under partial shading condition usi...eSAT Publishing House
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology.
AN ADAPTIVE EXTREMUM SEEKING CONTROL FOR REAL TIME OPTIMIZATION IN PHOTOVOLTA...Editor IJMTER
Extremum seeking control approach is a theory building a feedback system in such a
way that oscillation around the MPPT will boost the PV System efficiency .An alternative ESC
approach is to introduce a small amount of perturbation into the control system. Maximum Power
Point Tracker (MPPT) using extremum seeking control algorithm with emphasis in solar
photovoltaic (PV) system. The ESC is better because of its low cost ,high efficiency and good
power factor . Ripple Correlation Control(RCC) is used in first stage high pass filter along with the
relational operator to develop the system .The reason for choose RCC is due to its high voltage gain
and a low input current ripple which minimizes the oscillation at the module operation point .A
major advantage of ESC is that it is capable of improving the system performance .The variable
phase MPPT power ripple feedback signal developed by sensing and multiplying together PV array
.The entire system is simulated using Matlab simulink environment .The system is expected to be
operated with high efficiency and low cost long life time.
Final presentation of the Continue Final presentation of the Continued Development Program in Glyndwr University from Chernigiv State Technological University staff
Simulation of incremental conductance mppt with direct control method using c...eSAT Journals
Abstract PV Module Maximum Power Point Tracker (MPPT) is a photovoltaic system that uses the photovoltaic array as a source of electrical power supply. Every photovoltaic (PV) array has an optimum operating point, called the maximum power point, which varies depending on cell temperature, the insulation level and array voltage. The function of MPPT is needed to operate the PV array at its maximum power point. The design of a Maximum Peak Power Tracking (MPPT) is proposed utilizing a cuk converter topology. Solar panel voltage and current are continuously monitored by a MPPT, and the duty cycle of the cuk converter continuously adjusted to extract maximum power. The design consists of a PV array, DC-DC cuk converter and many such algorithms have been proposed. However, one particular algorithm, the Incremental Conductance method, claimed by many in the literature to be inferior to others, continues to be by far the most widely used method in commercial PV MPPT’s. The general model was implemented on Mat lab, and accepts irradiance and temperature as variable parameters and outputs the I-V characteristic and P-V characteristic Index Terms: PV system; Maximum power point tracking (MPPT); Incremental conductance (Inccond); digital signal processor (dsp)
Maximum Power Point Tracking Method for Single Phase Grid Connected PV System...Ali Mahmood
Ordinary technique fail to ensure successful tracking of the maximum power point under partial shading conditions (PSC). This performs in significant reduction in the power generated as well as the reliability of the photovoltaic energy production system. For the effective utilization of solar panel under partial shading condition (PSC), maximum power point tracking method (MPPT) is required.
Hey Guys,
This Project we made it for final year Engineering students and for well knowledge. It was an amazing experience when we made it successfully.
If you want this project then contact :
Kalpesh Badgujar - 8879254715
if any query about this project mail :
badgujarkalpesh201@gmail.com
Its a comparison of performance of MPPT controllers in case of solar PV array under same working conditions. The MPPT controllers used are Artificial Neural Network and P&O based.
Enhanced MPPT Technique For DC-DC Luo Converter Using Model Predictive Contro...IJERD Editor
The present study explored an enhanced maximum power point tracking technique which ensures fast tracking in PV systems. This system represents a Model Predictive Control (MPC) MPPT technique. Extracting the maximum power from PV systems has been widely investigated. The main benefaction of this article is an improvement of the Perturb and Observe (P&O) method through a fixed step predictive control under measured fast solar radiation. The preferred predictive control to achieve Maximum Power Point (MPP) speeds up the control loop since it predicts error before the switching signal is applied to the DC-DC Luo converter. Comparing the improved technique to the conventional P&O method indicates significant improvement in PV system performance. The proposed MPC-MPPT technique for a Luo converter is implemented using the MAT LAB SIMULINK
An Improved Constant Voltage Based MPPT Technique for PMDC MotorIAES-IJPEDS
Stand-alone photovoltaic (SAPV) systems are being used in remote areas
and are being seen as one of the promising solution in this regard. The SAPV
system as presented in the paper consists of solar PV panel, a DC-DC
converter, a controller and a PMDC motor. The current-voltage and powervoltage
characteristics being nonlinear, the SAPV system require maximum
power point techniques (MPPT) control techniques to extract maximum
power available from the PV cell. A voltage based MPPT technique which is
capable of tracking MPP has been selected because of numerous advantages
it offers such as: simple and low cost of implementation. The limitation of
constant voltage method is that its efficiency is low as the PV panel has to be
disconnected from the load for measurement of the open circuit voltage
(Voc). In the presented paper, the authors have removed this limitation by
using a pilot PV panel for measurement of Voc. A proportional-integrator (PI)
based controller is used in implementation of constant voltage MPP
technique and the modeling is done in MATLAB®/SIMULINK simulation
environment. The simulation results are presented and discussed in the paper,
the results shows that the efficiency of the system has increased.
Development of a Novel Robust Differential Maximum Power Point Tracking (MPPT...IJSRP Journal
The use of photovoltaic (PV) systems is increasingly growing in importance since they involve an exploitation of solar radiation constituting an energy source which is renewable, available in most places, and pollution-free. Despite their numerous advantages, PV systems have two major drawbacks: low energy conversion efficiency and loss of energy due to variations in meteorological conditions; for this reason, Maximum Power Point Tracking (MPPT) control techniques play a key role in exploiting the maximum energy caught by PV modules. The output characteristic of a photovoltaic array is nonlinear and changes with solar irradiation and the cell’s temperature. Therefore, a Maximum Power Point Tracking (MPPT) technique is needed to draw peak power from the solar array to maximize the produced energy. In this study we have analyzed the Maximum Power Point Tracking (MPPT) method and finding out a new and easier way to track maximum power point (MPP) and also our study is focused to overcome the drawbacks of MPPT. This research paper presents a novel MPP tracking method for tracking exact Maximum Power Point (MPP) if the irradiation or load changes.
Fuzzy logic based MPPT technique for a single phase Grid connected PV system ...THOKALA SOWMYA
In the proposed paper power generation from photovoltaic array is used to connect the grid. DFCM
Inverter control with PSPWM technique is used in order to control active and reactive power injected into grid. FLC
MPPT technique is proposed for maximum power point tracking and is compared with Constant voltage MPPT
technique. The simulation results of proposed system and Constant voltage MPPT technique are compared by using
MATLAB/SIMULINK software.
Maximum power point tracking of pv arrays under partial shading condition usi...eSAT Publishing House
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology.
AN ADAPTIVE EXTREMUM SEEKING CONTROL FOR REAL TIME OPTIMIZATION IN PHOTOVOLTA...Editor IJMTER
Extremum seeking control approach is a theory building a feedback system in such a
way that oscillation around the MPPT will boost the PV System efficiency .An alternative ESC
approach is to introduce a small amount of perturbation into the control system. Maximum Power
Point Tracker (MPPT) using extremum seeking control algorithm with emphasis in solar
photovoltaic (PV) system. The ESC is better because of its low cost ,high efficiency and good
power factor . Ripple Correlation Control(RCC) is used in first stage high pass filter along with the
relational operator to develop the system .The reason for choose RCC is due to its high voltage gain
and a low input current ripple which minimizes the oscillation at the module operation point .A
major advantage of ESC is that it is capable of improving the system performance .The variable
phase MPPT power ripple feedback signal developed by sensing and multiplying together PV array
.The entire system is simulated using Matlab simulink environment .The system is expected to be
operated with high efficiency and low cost long life time.
Final presentation of the Continue Final presentation of the Continued Development Program in Glyndwr University from Chernigiv State Technological University staff
Simulation of incremental conductance mppt with direct control method using c...eSAT Journals
Abstract PV Module Maximum Power Point Tracker (MPPT) is a photovoltaic system that uses the photovoltaic array as a source of electrical power supply. Every photovoltaic (PV) array has an optimum operating point, called the maximum power point, which varies depending on cell temperature, the insulation level and array voltage. The function of MPPT is needed to operate the PV array at its maximum power point. The design of a Maximum Peak Power Tracking (MPPT) is proposed utilizing a cuk converter topology. Solar panel voltage and current are continuously monitored by a MPPT, and the duty cycle of the cuk converter continuously adjusted to extract maximum power. The design consists of a PV array, DC-DC cuk converter and many such algorithms have been proposed. However, one particular algorithm, the Incremental Conductance method, claimed by many in the literature to be inferior to others, continues to be by far the most widely used method in commercial PV MPPT’s. The general model was implemented on Mat lab, and accepts irradiance and temperature as variable parameters and outputs the I-V characteristic and P-V characteristic Index Terms: PV system; Maximum power point tracking (MPPT); Incremental conductance (Inccond); digital signal processor (dsp)
Maximum Power Point Tracking Method for Single Phase Grid Connected PV System...Ali Mahmood
Ordinary technique fail to ensure successful tracking of the maximum power point under partial shading conditions (PSC). This performs in significant reduction in the power generated as well as the reliability of the photovoltaic energy production system. For the effective utilization of solar panel under partial shading condition (PSC), maximum power point tracking method (MPPT) is required.
Modeling of Photo Voltaic Module under Partial Shaded Conditions Using PSO MP...IJMTST Journal
In this paper a modified BOOST converter is presented for maximum power point tracking (MPPT) with PI
controller to improve the performance of PV system. SEPI converter is proposed as interface between load and
PV module array as DC-DC converter. Whichis more advantageous over boost converter for step up and step
down operations. The P&O and PSO based BOOST converter proposed are main key factors for high
efficiency output at foul weather conditions. The MATLAB/SIMULINK power system tool box will be used to
stimulate the proposed system.
Industrial Training at Shahjalal Fertilizer Company Limited (SFCL)MdTanvirMahtab2
This presentation is about the working procedure of Shahjalal Fertilizer Company Limited (SFCL). A Govt. owned Company of Bangladesh Chemical Industries Corporation under Ministry of Industries.
Cosmetic shop management system project report.pdfKamal Acharya
Buying new cosmetic products is difficult. It can even be scary for those who have sensitive skin and are prone to skin trouble. The information needed to alleviate this problem is on the back of each product, but it's thought to interpret those ingredient lists unless you have a background in chemistry.
Instead of buying and hoping for the best, we can use data science to help us predict which products may be good fits for us. It includes various function programs to do the above mentioned tasks.
Data file handling has been effectively used in the program.
The automated cosmetic shop management system should deal with the automation of general workflow and administration process of the shop. The main processes of the system focus on customer's request where the system is able to search the most appropriate products and deliver it to the customers. It should help the employees to quickly identify the list of cosmetic product that have reached the minimum quantity and also keep a track of expired date for each cosmetic product. It should help the employees to find the rack number in which the product is placed.It is also Faster and more efficient way.
Welcome to WIPAC Monthly the magazine brought to you by the LinkedIn Group Water Industry Process Automation & Control.
In this month's edition, along with this month's industry news to celebrate the 13 years since the group was created we have articles including
A case study of the used of Advanced Process Control at the Wastewater Treatment works at Lleida in Spain
A look back on an article on smart wastewater networks in order to see how the industry has measured up in the interim around the adoption of Digital Transformation in the Water Industry.
Water scarcity is the lack of fresh water resources to meet the standard water demand. There are two type of water scarcity. One is physical. The other is economic water scarcity.
NO1 Uk best vashikaran specialist in delhi vashikaran baba near me online vas...Amil Baba Dawood bangali
Contact with Dawood Bhai Just call on +92322-6382012 and we'll help you. We'll solve all your problems within 12 to 24 hours and with 101% guarantee and with astrology systematic. If you want to take any personal or professional advice then also you can call us on +92322-6382012 , ONLINE LOVE PROBLEM & Other all types of Daily Life Problem's.Then CALL or WHATSAPP us on +92322-6382012 and Get all these problems solutions here by Amil Baba DAWOOD BANGALI
#vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore#blackmagicformarriage #aamilbaba #kalajadu #kalailam #taweez #wazifaexpert #jadumantar #vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore #blackmagicforlove #blackmagicformarriage #aamilbaba #kalajadu #kalailam #taweez #wazifaexpert #jadumantar #vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore #Amilbabainuk #amilbabainspain #amilbabaindubai #Amilbabainnorway #amilbabainkrachi #amilbabainlahore #amilbabaingujranwalan #amilbabainislamabad
Immunizing Image Classifiers Against Localized Adversary Attacksgerogepatton
This paper addresses the vulnerability of deep learning models, particularly convolutional neural networks
(CNN)s, to adversarial attacks and presents a proactive training technique designed to counter them. We
introduce a novel volumization algorithm, which transforms 2D images into 3D volumetric representations.
When combined with 3D convolution and deep curriculum learning optimization (CLO), itsignificantly improves
the immunity of models against localized universal attacks by up to 40%. We evaluate our proposed approach
using contemporary CNN architectures and the modified Canadian Institute for Advanced Research (CIFAR-10
and CIFAR-100) and ImageNet Large Scale Visual Recognition Challenge (ILSVRC12) datasets, showcasing
accuracy improvements over previous techniques. The results indicate that the combination of the volumetric
input and curriculum learning holds significant promise for mitigating adversarial attacks without necessitating
adversary training.
About
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.
Technical Specifications
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
Key Features
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface
• Compatible with MAFI CCR system
• Copatiable with IDM8000 CCR
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
Application
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.