This document evaluates the corrosion rate of steel reinforcement in concrete with varying water-cement ratios (W/C). Specimens with W/C ratios of 0.4, 0.45, 0.5, and 0.55 were tested using accelerated corrosion and weight loss methods. The corrosion rate increased with higher W/C ratios, from 0.0243 mm/year for 0.4 W/C to 0.1436 mm/year for 0.55 W/C. Chloride permeability also increased with W/C ratio, from low permeability for 0.4 W/C to moderate permeability for 0.55 W/C. The study found that corrosion rate and chloride permeability rise with increasing water
Effect of deep cryogenic treatment on surface integrity and dimensional stabi...eSAT Journals
Abstract Deep cryogenic treatment is an add-on process to conventional heat treatment in which material is treated at cryogenic temperature. The mechanical properties of the tool steel are significantly improved by Deep Cryogenic treatment. Surface integrity and dimensional stability is having greater impact on the functional performance of the tool during service conditions. The objective of this work is to investigate the effect of deep cryogenic treatment on the surface integrity and dimensional stability of the D2 tool steel. The metallographic samples and Navy C Rings of D2 Tool steel were treated at cryogenic temperature of -1930C after hardening and tempering. Results have shown improvement in surface roughness. The improved surface roughness is attributed to the release of tensile residual stresses and more precipitation and uniform distribution of fine secondary carbides. DCT have higher shape distortion than CHT. The distortions in DCT can be attributed to the section sensitivity of D2 Tool steel. Keywords: Surface integrity, distortion, precipitation of secondary carbides, section sensitivity
Effects of cryogenic treatment on tool steel aisi d6eSAT Journals
Abstract
In present technological modern age. All the manufacturers adopt that process which governs to higher productivity that has been achieved by the various treatment of tool steel. These conventional processes improve no of characteristics to fulfill desired purpose. But all these process does not provided fully satisfaction from conventional heat treatment process. Thus a new process is being additionally employed for improving mechanical properties called cryogenic treatment process or sub-zero treatment of tool steels. During this process tool steel is proceed below Atmospheric tem. That is in minus about (-1960 C or 3100 F). Due to cooling, steel alter their mechanical properties like wear resistance, Hardness, toughness, fatigue life micro-structure alteration etc. Cryo-treatment not only improve its mechanical properties but also improve thermal properties, electrical properties & easier machining etc. in this paper cryogenic treatment of tool steel AISI-D6 is perform and study is made for wear-resistance, Hardness, toughness, with respect to untreated test specimen of same, we have got improved wear-resistance capacity improve hardness as well as toughness.
Keywords – AISI-D6 tool steel, cryogenic process, wear resistance, Hardness, Toughness.
Heat Transfer, Hardenability and Steel Phase Transformations during Gas Quenc...YuanLu49
https://digitalcommons.wpi.edu/etd-dissertations/399/
"Quenching is the rapid cooling process from an elevated temperature. Compared to water and oil quench medium, high pressure and velocity gas is preferred to quench medium and high hardenability steel, with the potential to reduce distortion, stress and cracks. Currently, no standard test exists to characterize the gas quench steel hardenability and measure the performance of industrial gas quench furnaces. In this thesis, the fundamental difference between the liquid and gas quenching, heat transfer coefficient, was emphasized. It has been proven that gas quenching with constant HTC cannot generate the similar cooling curves compared to liquid quenching. Limitations on current gas quench steel hardenability tests were reviewed. Critical HTC, a concept like critical diameter, was successfully proved to describe the gas quench hardenability of steel. An attempt to use critical HTC test bar and measure the HTC distribution of gas quench furnace was made. Gas quenching, usually with slow cooling rate, may reduce hardness and Charpy impact toughness, compared to water and oil quenching. Lattice parameter and c/a ratio of as-quenched martensite in steel was measured using high resolution X-ray diffraction and Rietveld refinement. For AISI 4140, Charpy impact toughness decreases when the cooling rate decreases after quenching and tempering. Austenite percentage and carbon content in austenite is proposed as the dominated mechanism."
Effect of deep cryogenic treatment on surface integrity and dimensional stabi...eSAT Journals
Abstract Deep cryogenic treatment is an add-on process to conventional heat treatment in which material is treated at cryogenic temperature. The mechanical properties of the tool steel are significantly improved by Deep Cryogenic treatment. Surface integrity and dimensional stability is having greater impact on the functional performance of the tool during service conditions. The objective of this work is to investigate the effect of deep cryogenic treatment on the surface integrity and dimensional stability of the D2 tool steel. The metallographic samples and Navy C Rings of D2 Tool steel were treated at cryogenic temperature of -1930C after hardening and tempering. Results have shown improvement in surface roughness. The improved surface roughness is attributed to the release of tensile residual stresses and more precipitation and uniform distribution of fine secondary carbides. DCT have higher shape distortion than CHT. The distortions in DCT can be attributed to the section sensitivity of D2 Tool steel. Keywords: Surface integrity, distortion, precipitation of secondary carbides, section sensitivity
Effects of cryogenic treatment on tool steel aisi d6eSAT Journals
Abstract
In present technological modern age. All the manufacturers adopt that process which governs to higher productivity that has been achieved by the various treatment of tool steel. These conventional processes improve no of characteristics to fulfill desired purpose. But all these process does not provided fully satisfaction from conventional heat treatment process. Thus a new process is being additionally employed for improving mechanical properties called cryogenic treatment process or sub-zero treatment of tool steels. During this process tool steel is proceed below Atmospheric tem. That is in minus about (-1960 C or 3100 F). Due to cooling, steel alter their mechanical properties like wear resistance, Hardness, toughness, fatigue life micro-structure alteration etc. Cryo-treatment not only improve its mechanical properties but also improve thermal properties, electrical properties & easier machining etc. in this paper cryogenic treatment of tool steel AISI-D6 is perform and study is made for wear-resistance, Hardness, toughness, with respect to untreated test specimen of same, we have got improved wear-resistance capacity improve hardness as well as toughness.
Keywords – AISI-D6 tool steel, cryogenic process, wear resistance, Hardness, Toughness.
Heat Transfer, Hardenability and Steel Phase Transformations during Gas Quenc...YuanLu49
https://digitalcommons.wpi.edu/etd-dissertations/399/
"Quenching is the rapid cooling process from an elevated temperature. Compared to water and oil quench medium, high pressure and velocity gas is preferred to quench medium and high hardenability steel, with the potential to reduce distortion, stress and cracks. Currently, no standard test exists to characterize the gas quench steel hardenability and measure the performance of industrial gas quench furnaces. In this thesis, the fundamental difference between the liquid and gas quenching, heat transfer coefficient, was emphasized. It has been proven that gas quenching with constant HTC cannot generate the similar cooling curves compared to liquid quenching. Limitations on current gas quench steel hardenability tests were reviewed. Critical HTC, a concept like critical diameter, was successfully proved to describe the gas quench hardenability of steel. An attempt to use critical HTC test bar and measure the HTC distribution of gas quench furnace was made. Gas quenching, usually with slow cooling rate, may reduce hardness and Charpy impact toughness, compared to water and oil quenching. Lattice parameter and c/a ratio of as-quenched martensite in steel was measured using high resolution X-ray diffraction and Rietveld refinement. For AISI 4140, Charpy impact toughness decreases when the cooling rate decreases after quenching and tempering. Austenite percentage and carbon content in austenite is proposed as the dominated mechanism."
Studies on Corrosion Characteristics of Carbon Steel Exposed to Na2CO3, Na2SO...theijes
The International Journal of Engineering & Science is aimed at providing a platform for researchers, engineers, scientists, or educators to publish their original research results, to exchange new ideas, to disseminate information in innovative designs, engineering experiences and technological skills. It is also the Journal's objective to promote engineering and technology education. All papers submitted to the Journal will be blind peer-reviewed. Only original articles will be published.
The papers for publication in The International Journal of Engineering& Science are selected through rigorous peer reviews to ensure originality, timeliness, relevance, and readability.
Experimental Analysis using Established Parameters for Cryogenic Treatment on...IJAEMSJORNAL
The experimental analysis on cutting tool material is done with referring the established parameters for Cryogenic Treatment. The pilot experimentation is carried out using the Conventional heat treated tool bits as supplied condition and Cryogenic treated tools. The three grades of high speed steel are identified for the investigation purpose and for pilot experimentation H.S.S. T42 grade is selected. The tool material procured is strictly as per the grade specifications for the investigation of effect of cryogenic treatment on tool life. The established parameters for cryogenic treatment are identified referring to previous published research and machining parameters as per the industry specifications. The pilot experimentation using Untreated and treated tools are subjected to turning operation on CNC turning center for a definite work material and machining parameters such as cutting speed, feed and depth of cut are identified. Single point cutting Tool geometry is maintained as per the tool signature and length of the tool is maintained as per the limitations of the machine. The Surface Roughness of the machined work piece is measured using the Taylor Hob-son Surface Roughness tester and the Tool wear is measured using the Tool Makers microscope. The results are tabulated. An experimental effort to understand the effect of Untreated and Cryogenic treated tool on the tool life is the outcome of this paper. The outcome of this paper forms the basis of experimentation using the Orthogonal array for all the selected grades of the material.
Corrosion fatigue crack growth experiment was conducted on ESE(T) (Eccentrically-loaded Single Edge notch Tension) specimen made of IS 2062 steel in salt water environment. The specimen was placed in a transparent chamber made of perspex sheet containing 3.5% NaCl solution which acted as corrosion environment. The corrosion process was accelerated by applying constant direct current of 0.2 A which was supplied by means of a regulated power supply. The test was conducted using a ±250 kN capacity computer controlled servo-hydraulic fatigue rated Universal Testing Machine. The maximum and minimum load values were 15 kN and 1.5 kN. The test frequency was 0.375 Hz and the stress ratio was 0.1. Number of cycles to crack initiation was determined. Crack growth data were recorded at regular intervals. Crack growth curves were plotted and material constants C and m were found. Analytical studies were carried out and the results were compared with experimental results. Details of the analytical and experimental studies and the results are presented in this paper.
Investigation on Effect of Heat Input on Cooling Rate and Mechanical Property...IJMER
The effect of heat input in MMAW arc welding on cooling rate and hardness of weld
joint is investigated in this paper. The parameter affects the heat input are welding current, arc voltage
and welding speed. Mild steel weldments were welded under varying current 80, 90 and 100 ampere
and keeping arc voltage and travel speed constant. Other mild steel specimens were welded under
varying arc voltage 21V, 23V and 25V and keeping welding current and welding speed constant. Other
mild steel specimens were welded by varying welding travel speed 1.52 mm/sec, 1.67 mm/sec and 1.82
mm/sec and keeping arc voltage and welding current constant. Heat input was calculated for each
weldment. Rockwell hardness testing of all specimens was done. It was observed that with increase in
arc current hardness of mild steel weld joint was increased up to optimum level and then decreased.
Cooling rate was decreased with increased in arc current. With increase in welding arc voltage
hardness of weld joint decreased and cooling rate was decreased also. With increase in welding travel
speed hardness of weld joint increased and cooling rate was increased also.
Cryogenic treatment is a secondary process to traditional heat treatment used for improving the hardness and wear resistance of tool steels. Though the potential use of cryogenic treatment on AISI D2 tool steel under laboratory conditions has been well established by the researchers, it is essential to do the analysis to ensure its sustainable use for industrial application. Therefore, impact of cryogenic treatment on AISI D2 steel blanking punch was evaluated in terms of increase in production rate and its life. The cryogenically treated D2 tool steel punches were used and subjected to manufacture the control levers using blanking operations. The improved wear resistance of cryogenically treated punch resulted in increase in production and punch life more than 200%. Punch life was studied and correlated to increase in production & wear behavior of blanking punch. The AISI D2 steel samples were prepared and subjected to laboratory tests comprising of metallographic observations and hardness. It was found that laboratory tests were not enough to predict improvements in mechanical properties. The mechanism responsible for augmented wear resistance by cryogenic treatment was the conversion of retained austenite to martensite and precipitation of new secondary carbides.
The International Journal of Engineering and Science (The IJES)theijes
The International Journal of Engineering & Science is aimed at providing a platform for researchers, engineers, scientists, or educators to publish their original research results, to exchange new ideas, to disseminate information in innovative designs, engineering experiences and technological skills. It is also the Journal's objective to promote engineering and technology education. All papers submitted to the Journal will be blind peer-reviewed. Only original articles will be published.
1-1 Influence of Multi Extrusion Die Process on Mechanical and Chemical Behav...Ahmed Ibrahim Razooqi
INFLUENCE OF MULTI EXTRUSION DIE PROCESS ON MECHANICAL
AND CHEMICAL BEHAVIOR OF 2024-T3 ALLOY.
Ahmed Ibrahim RAZOOQI
Technical Engineering College - Baghdad, Middle Technical University, Baghdad, IRAQ
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology
Studies on Corrosion Characteristics of Carbon Steel Exposed to Na2CO3, Na2SO...theijes
The International Journal of Engineering & Science is aimed at providing a platform for researchers, engineers, scientists, or educators to publish their original research results, to exchange new ideas, to disseminate information in innovative designs, engineering experiences and technological skills. It is also the Journal's objective to promote engineering and technology education. All papers submitted to the Journal will be blind peer-reviewed. Only original articles will be published.
The papers for publication in The International Journal of Engineering& Science are selected through rigorous peer reviews to ensure originality, timeliness, relevance, and readability.
Experimental Analysis using Established Parameters for Cryogenic Treatment on...IJAEMSJORNAL
The experimental analysis on cutting tool material is done with referring the established parameters for Cryogenic Treatment. The pilot experimentation is carried out using the Conventional heat treated tool bits as supplied condition and Cryogenic treated tools. The three grades of high speed steel are identified for the investigation purpose and for pilot experimentation H.S.S. T42 grade is selected. The tool material procured is strictly as per the grade specifications for the investigation of effect of cryogenic treatment on tool life. The established parameters for cryogenic treatment are identified referring to previous published research and machining parameters as per the industry specifications. The pilot experimentation using Untreated and treated tools are subjected to turning operation on CNC turning center for a definite work material and machining parameters such as cutting speed, feed and depth of cut are identified. Single point cutting Tool geometry is maintained as per the tool signature and length of the tool is maintained as per the limitations of the machine. The Surface Roughness of the machined work piece is measured using the Taylor Hob-son Surface Roughness tester and the Tool wear is measured using the Tool Makers microscope. The results are tabulated. An experimental effort to understand the effect of Untreated and Cryogenic treated tool on the tool life is the outcome of this paper. The outcome of this paper forms the basis of experimentation using the Orthogonal array for all the selected grades of the material.
Corrosion fatigue crack growth experiment was conducted on ESE(T) (Eccentrically-loaded Single Edge notch Tension) specimen made of IS 2062 steel in salt water environment. The specimen was placed in a transparent chamber made of perspex sheet containing 3.5% NaCl solution which acted as corrosion environment. The corrosion process was accelerated by applying constant direct current of 0.2 A which was supplied by means of a regulated power supply. The test was conducted using a ±250 kN capacity computer controlled servo-hydraulic fatigue rated Universal Testing Machine. The maximum and minimum load values were 15 kN and 1.5 kN. The test frequency was 0.375 Hz and the stress ratio was 0.1. Number of cycles to crack initiation was determined. Crack growth data were recorded at regular intervals. Crack growth curves were plotted and material constants C and m were found. Analytical studies were carried out and the results were compared with experimental results. Details of the analytical and experimental studies and the results are presented in this paper.
Investigation on Effect of Heat Input on Cooling Rate and Mechanical Property...IJMER
The effect of heat input in MMAW arc welding on cooling rate and hardness of weld
joint is investigated in this paper. The parameter affects the heat input are welding current, arc voltage
and welding speed. Mild steel weldments were welded under varying current 80, 90 and 100 ampere
and keeping arc voltage and travel speed constant. Other mild steel specimens were welded under
varying arc voltage 21V, 23V and 25V and keeping welding current and welding speed constant. Other
mild steel specimens were welded by varying welding travel speed 1.52 mm/sec, 1.67 mm/sec and 1.82
mm/sec and keeping arc voltage and welding current constant. Heat input was calculated for each
weldment. Rockwell hardness testing of all specimens was done. It was observed that with increase in
arc current hardness of mild steel weld joint was increased up to optimum level and then decreased.
Cooling rate was decreased with increased in arc current. With increase in welding arc voltage
hardness of weld joint decreased and cooling rate was decreased also. With increase in welding travel
speed hardness of weld joint increased and cooling rate was increased also.
Cryogenic treatment is a secondary process to traditional heat treatment used for improving the hardness and wear resistance of tool steels. Though the potential use of cryogenic treatment on AISI D2 tool steel under laboratory conditions has been well established by the researchers, it is essential to do the analysis to ensure its sustainable use for industrial application. Therefore, impact of cryogenic treatment on AISI D2 steel blanking punch was evaluated in terms of increase in production rate and its life. The cryogenically treated D2 tool steel punches were used and subjected to manufacture the control levers using blanking operations. The improved wear resistance of cryogenically treated punch resulted in increase in production and punch life more than 200%. Punch life was studied and correlated to increase in production & wear behavior of blanking punch. The AISI D2 steel samples were prepared and subjected to laboratory tests comprising of metallographic observations and hardness. It was found that laboratory tests were not enough to predict improvements in mechanical properties. The mechanism responsible for augmented wear resistance by cryogenic treatment was the conversion of retained austenite to martensite and precipitation of new secondary carbides.
The International Journal of Engineering and Science (The IJES)theijes
The International Journal of Engineering & Science is aimed at providing a platform for researchers, engineers, scientists, or educators to publish their original research results, to exchange new ideas, to disseminate information in innovative designs, engineering experiences and technological skills. It is also the Journal's objective to promote engineering and technology education. All papers submitted to the Journal will be blind peer-reviewed. Only original articles will be published.
1-1 Influence of Multi Extrusion Die Process on Mechanical and Chemical Behav...Ahmed Ibrahim Razooqi
INFLUENCE OF MULTI EXTRUSION DIE PROCESS ON MECHANICAL
AND CHEMICAL BEHAVIOR OF 2024-T3 ALLOY.
Ahmed Ibrahim RAZOOQI
Technical Engineering College - Baghdad, Middle Technical University, Baghdad, IRAQ
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology
This is a presentation on hydrogen induced cracking ,sulfide stress cracking and test procedure for HIC resistant steel
DENZIL D’SOUZA
denzil22@gmail.com
Effects of anion on the corrosion behaviors of carbon steel under artificial ...eSAT Journals
Abstract
Rain is one of the main importance issues for atmospheric corrosion problem. Effects of rainfall on corrosion behaviors of carbon steels were investigated using artificial rainfall equipment. Three types of Atmospheric Corrosion Monitoring (ACM) sensors, which consist of Fe-Ag, Zn-Ag, and Al-Ag galvanic couples, were used to illustrate the correlation between the sensors output, Corrosion Rate (CR), and chemical concentration in the rain. The effects of ionic species on the corrosion behaviors were observed by using NaCl, KCl, Na2SO4, NaNO3, and KNO3 as rainfall solutions. The result revealed that the rainfall rate was insensitive to ACM sensors outputs and CRs. In contrast, the chemical species and their concentrations in the rainfall solution significantly affected the ACM outputs and CRs. The corrosivity of the cations (Na+ and K+) is negligible compared to the anions (Cl-, SO42-, NO3-).For a given number of molar concentration, the CRs resulted from the corrosivity of SO4-2anions were higher than that of Cl- and NO3- anions, respectively. According to the empirical data, the CRs is increased and then reach a steady state as the molar concentration is continuously increased. This research also indicates that the ACM sensors outputs of Fe-Ag and Zn-Ag couples are capable of estimating corrosivity of the atmosphere, while the ACM sensor of Al-Agcouple can be used to determine not only the time of wetness but also the typeofchemical species in the environment. The research methods discussed in this paper proves that the CRs are dependent on the atmospheric composition and can be forecasted through ACM sensors.
Effects of anion on the corrosion behaviors of carbon steel under artificial ...eSAT Journals
Abstract
Rain is one of the main importance issues for atmospheric corrosion problem. Effects of rainfall on corrosion behaviors of carbon steels were investigated using artificial rainfall equipment. Three types of Atmospheric Corrosion Monitoring (ACM) sensors, which consist of Fe-Ag, Zn-Ag, and Al-Ag galvanic couples, were used to illustrate the correlation between the sensors output, Corrosion Rate (CR), and chemical concentration in the rain. The effects of ionic species on the corrosion behaviors were observed by using NaCl, KCl, Na2SO4, NaNO3, and KNO3 as rainfall solutions. The result revealed that the rainfall rate was insensitive to ACM sensors outputs and CRs. In contrast, the chemical species and their concentrations in the rainfall solution significantly affected the ACM outputs and CRs. The corrosivity of the cations (Na+ and K+) is negligible compared to the anions (Cl-, SO42-, NO3-).For a given number of molar concentration, the CRs resulted from the corrosivity of SO4-2anions were higher than that of Cl- and NO3- anions, respectively. According to the empirical data, the CRs is increased and then reach a steady state as the molar concentration is continuously increased. This research also indicates that the ACM sensors outputs of Fe-Ag and Zn-Ag couples are capable of estimating corrosivity of the atmosphere, while the ACM sensor of Al-Agcouple can be used to determine not only the time of wetness but also the typeofchemical species in the environment. The research methods discussed in this paper proves that the CRs are dependent on the atmospheric composition and can be forecasted through ACM sensors.
Investigation of mechanical properties of carbidic ductile cast ironRSIS International
The objective of the present work is to increase the wear resistance for long life of applications. It is found that increase in the carbides in an alloy which resulted in to enhancement in hardness and wear resistance. The wear resistance was evaluated by testing in accordance with ASTE International Committee G-99 Standard. An improved performance of wear resistanceis obtained by increasing the content of chromium in the carbidic ductile cast iron. The results are discussed based on the influence of chromium content on the casting.
Piping systems associated with production, transporting oil & gas, water/gas injection into reservoirs, experience wear & tear with time & operations. There would be metal loss due to erosion, erosion-corrosion and cavitation to name a few. The presence of corrosion defects provides a means for localized fractures to propagate causing pipe ruptures & leakages. This also reduces the pipe/pipeline maximum allowable operating pressure [MAOP].
The following document covers methods by DNV standards to quantitatively estimate the erosion rate for ductile pipes and bends due to the presence of sand. It is to be noted that corrosion can occur in many other scenarios such as pipe dimensioning, flow rate limitations, pipe performance such as pressure drop, vibrations, noise, insulation, hydrate formation and removal, severe slug flow, terrain slugging and also upheaval buckling. However these aspects are not covered in this document.
Based on the erosional rates of pipes and bends, the Maximum Safe Pressure/Revised MAOP is evaluated based on a Level 1 Assessment procedure for the remaining strength of the pipeline. The Level 1 procedures taken up in this tutorial are RSTRENG 085dL method, DNVGL RP F-101 (Part-B) and PETROBRAS’s PB Equation.
Hierarchical Digital Twin of a Naval Power SystemKerry Sado
A hierarchical digital twin of a Naval DC power system has been developed and experimentally verified. Similar to other state-of-the-art digital twins, this technology creates a digital replica of the physical system executed in real-time or faster, which can modify hardware controls. However, its advantage stems from distributing computational efforts by utilizing a hierarchical structure composed of lower-level digital twin blocks and a higher-level system digital twin. Each digital twin block is associated with a physical subsystem of the hardware and communicates with a singular system digital twin, which creates a system-level response. By extracting information from each level of the hierarchy, power system controls of the hardware were reconfigured autonomously. This hierarchical digital twin development offers several advantages over other digital twins, particularly in the field of naval power systems. The hierarchical structure allows for greater computational efficiency and scalability while the ability to autonomously reconfigure hardware controls offers increased flexibility and responsiveness. The hierarchical decomposition and models utilized were well aligned with the physical twin, as indicated by the maximum deviations between the developed digital twin hierarchy and the hardware.
Overview of the fundamental roles in Hydropower generation and the components involved in wider Electrical Engineering.
This paper presents the design and construction of hydroelectric dams from the hydrologist’s survey of the valley before construction, all aspects and involved disciplines, fluid dynamics, structural engineering, generation and mains frequency regulation to the very transmission of power through the network in the United Kingdom.
Author: Robbie Edward Sayers
Collaborators and co editors: Charlie Sims and Connor Healey.
(C) 2024 Robbie E. Sayers
CFD Simulation of By-pass Flow in a HRSG module by R&R Consult.pptxR&R Consult
CFD analysis is incredibly effective at solving mysteries and improving the performance of complex systems!
Here's a great example: At a large natural gas-fired power plant, where they use waste heat to generate steam and energy, they were puzzled that their boiler wasn't producing as much steam as expected.
R&R and Tetra Engineering Group Inc. were asked to solve the issue with reduced steam production.
An inspection had shown that a significant amount of hot flue gas was bypassing the boiler tubes, where the heat was supposed to be transferred.
R&R Consult conducted a CFD analysis, which revealed that 6.3% of the flue gas was bypassing the boiler tubes without transferring heat. The analysis also showed that the flue gas was instead being directed along the sides of the boiler and between the modules that were supposed to capture the heat. This was the cause of the reduced performance.
Based on our results, Tetra Engineering installed covering plates to reduce the bypass flow. This improved the boiler's performance and increased electricity production.
It is always satisfying when we can help solve complex challenges like this. Do your systems also need a check-up or optimization? Give us a call!
Work done in cooperation with James Malloy and David Moelling from Tetra Engineering.
More examples of our work https://www.r-r-consult.dk/en/cases-en/
Cosmetic shop management system project report.pdfKamal Acharya
Buying new cosmetic products is difficult. It can even be scary for those who have sensitive skin and are prone to skin trouble. The information needed to alleviate this problem is on the back of each product, but it's thought to interpret those ingredient lists unless you have a background in chemistry.
Instead of buying and hoping for the best, we can use data science to help us predict which products may be good fits for us. It includes various function programs to do the above mentioned tasks.
Data file handling has been effectively used in the program.
The automated cosmetic shop management system should deal with the automation of general workflow and administration process of the shop. The main processes of the system focus on customer's request where the system is able to search the most appropriate products and deliver it to the customers. It should help the employees to quickly identify the list of cosmetic product that have reached the minimum quantity and also keep a track of expired date for each cosmetic product. It should help the employees to find the rack number in which the product is placed.It is also Faster and more efficient way.
Student information management system project report ii.pdfKamal Acharya
Our project explains about the student management. This project mainly explains the various actions related to student details. This project shows some ease in adding, editing and deleting the student details. It also provides a less time consuming process for viewing, adding, editing and deleting the marks of the students.
Industrial Training at Shahjalal Fertilizer Company Limited (SFCL)MdTanvirMahtab2
This presentation is about the working procedure of Shahjalal Fertilizer Company Limited (SFCL). A Govt. owned Company of Bangladesh Chemical Industries Corporation under Ministry of Industries.
Welcome to WIPAC Monthly the magazine brought to you by the LinkedIn Group Water Industry Process Automation & Control.
In this month's edition, along with this month's industry news to celebrate the 13 years since the group was created we have articles including
A case study of the used of Advanced Process Control at the Wastewater Treatment works at Lleida in Spain
A look back on an article on smart wastewater networks in order to see how the industry has measured up in the interim around the adoption of Digital Transformation in the Water Industry.