This document provides an addendum to the GSMV/GSMVCN GSM Cellular Communicator Installation and Setup Guide. It includes the following information: 1. Electrical specifications for the included AC transformer, including input power of 16.5VAC and positive/negative trigger voltage levels. 2. Wiring diagrams for connecting the GSMV zone input for positive and negative triggers, noting the required voltage levels for each. 3. Details on powering the communication module from the AC transformer for standard installations or from the control panel for ECP or ULC installations.

1. ADDENDUM TO: GSMV / GSMVCN GSM Cellular Communicator Installation and
Setup Guide
Installation and Setup Guide – use with issue 800-07349, dated 8/10
RE: Information should be as shown below.
Section 1 General Information (page 1–3)
Electrical
Input Power: 16.5VAC, 40VA transformer, Honeywell Model No. 1361/1361CN in Canada (included)
Positive Trigger Level: 6V or greater = positive trigger. (4V or less = restore.)
Negative Trigger Level: 4V or less = negative trigger. (6V or greater = restore.)
Section 2 Mounting and Wiring
Wiring for Zone Trigger Mode (page 2-6)
To trip a zone using a positive trigger, the voltage level must be:
6V or greater = positive trigger. (Levels above +14V may cause damage to the unit.)
4V or less = restore.
To trip a zone using a negative trigger, the voltage level must be:
4V or less = negative trigger.
6V or greater = restore. (Levels above +14V may cause damage to the unit.)
Note: Remember to program the communications module zone for the desired trigger type.
Connect a wire from the triggering source (bell output, voltage trigger, etc.) of the control panel to the
zone input of the module, and connect a common ground between the module and control panel.
Examples of zone connections follow:
TRANSFORMER TB1
1 AC INPUT 1
2 AC INPUT 2
GND 4 GND
+ TRIGGER 5 ZONE INPUT Z1/Z2
(VOLTAGE: 6 to 13V)
J1 BATTERY
COMMUNICATIONS
TRIGGERING DEVICE MODULE GSMV-005-V0
Figure 2-3. Wiring the GSMV Zone 1 Input for a Positive Trigger
TRANSFORMER TB1
1 AC INPUT 1
2 AC INPUT 2
GND 4 GND
-TRIGGER 5 ZONE INPUT Z1/Z2
(VOLTAGE 4 to 0V)
J1 BATTERY
TRIGGERING DEVICE
COMMUNICATIONS
MODULE GSMV-006-V0
Figure 2-4. Wiring the GSMV Zone 1 Input for a Negative Trigger

2. Powering the Communication Module (page 2-7)
For a standard installation, primary power is provided by the AC plug-in transformer. For
ECP communication, you must also connect the +12VDC AUX voltage output of the control
panel (9.6V-13.8V typical) (see Figure 2-7).
In all installations, TB1-4 GND must be connected to ground (GND) on the control panel.
For a ULC installation, primary power must be provided by the control panel.
TRANSFORMER TB1
1 AC INPUT 1
2 AC INPUT 2
3 ECP (+) VOLTAGE INPUT
12V AUX
Standard GND
GND 4
Installation
iGSMBR-013-V0
J1 BATTERY
CONTROL PANEL
COMMUNICATIONS
MODULE
TB1
NO CONNECTION 1 AC INPUT 1
NO CONNECTION 2 AC INPUT 2
RED
+12 V AUX 3 ECP (+) VOLTAGE INPUT
GND BLK GND
4
ULC YEL
DATA OUT
Installation 5 ECP DATA IN
GRN
DATA IN 6 ECP DATA OUT
J1
CONTROL PANEL
NO CONNECTION
NOTE: DO NOT CONNECT THE COMMUNICATION
MODULE BACKUP BATTERY OR TRANSFORMER
FOR COMMERCIAL FIRE & BURGLARY INSTALLATIONS. COMMUNICATION MODULE comm_mod-001-V1
Figure 2-7. Powering the Communications Module
2 Corporate Center Drive, Suite 100
P.O. Box 9040, Melville, NY 11747
Ê800-07349XX)Š Copyright ! 2010 Honeywell International Inc.
800-07349XX 01/11 Rev. A www.honeywell.com/security