This document presents a comparative study of materials used for organic field effect transistors (OFETs). It discusses the device structure and operating principles of OFETs. Both organic and inorganic dielectric materials are considered for use in OFETs, with the goal of low power consumption. Common p-type and n-type organic semiconductor materials used in OFETs are described, including small molecules like pentacene, rubrene, and fullerene, as well as polymers like P3HT and PBTTT. Key OFET parameters such as field effect mobility, threshold voltage, on/off current ratio, and subthreshold swing are also defined and their relationships to material properties are explained.
Optimization of 14 nm double gate Bi-GFET for lower leakage currentTELKOMNIKA JOURNAL
In recent years, breakthroughs in electronics technology have resulted in upgrades in the physical properties of the metal oxide semiconductor field effect transistor (MOSFET) toward smaller sizes and improvements in both quality and performance. Hence, the growth field effect transistor (GFET) is being promoted as one of the worthy contenders due to its superior material characteristics. A 14 nm horizontal double-gate bilayer graphene FET with a high-k/metal gate is proposed, which is composed of hafnium dioxide (HfO2) and tungsten silicide (WSix) respectively. It is simulated and modelled using silvaco ATHENA and ATLAS technology computer-aided design (TCAD) tools, as well as the Taguchi L9 orthogonal array (OA). The threshold voltage (VTH) adjustment implant dose, VTH adjustment implant energy, source/drain (S/D) implant dose, and S/D implant energy have all been investigated as process parameters. While the VTH adjustment tilt angle and the S/D implant tilt angle have both been investigated as noise factors. When compared to the initial findings before optimization, the IOFF has a value of 29.579 nA/µm, indicating a significant improvement. Findings from the optimization technique demonstrate excellent device performance with an IOFF of 28.564 nA/µm, which is closer to the international technology roadmap semiconductor (ITRS) 2013 target than before
Geometric and process design of ultra-thin junctionless double gate vertical ...IJECEIAES
The junctionless MOSFET architectures appear to be attractive in realizing the Moore’s law prediction. In this paper, a comprehensive 2-D simulation on junctionless vertical double-gate MOSFET (JLDGVM) under geometric and process consideration was introduced in order to obtain excellent electrical characteristics. Geometrical designs such as channel length (Lch) and pillar thickness (Tp) were considered and the impact on the electrical performance was analyzed. The influence of doping concentration and metal gate work function (WF) were further investigated for achieving better performance. The results show that the shorter Lch can boost the drain current (ID) of n-JLDGVM and p-JLDGVM by approximately 68% and 70% respectively. The ID of the n-JLVDGM and p-JLVDGM could possibly boost up to 42% and 78% respectively as the Tp is scaled down from 11nm to 8nm. The channel doping (Nch) is also a critical parameter, affecting the electrical performance of both n-JLDGVM and p-JLDGVM in which 15% and 39% improvements are observed in their respective ID as the concentration level is increased from 1E18 to 9E18 atom/cm3. In addition, the adjustment of threshold voltage can be realized by varying the metal WF.
Simulation study of single event effects sensitivity on commercial power MOSF...journalBEEI
High-frequency semiconductor devices are key components for advanced power electronic system that require fast switching speed. Power Metal Oxide Semiconductor Field Effect Transistor (MOSFET) is the most famous electronic device that are used in much power electronic system. However, the application such as space borne, military and communication system needs Power MOSFET to withstand in radiation environments. This is very challenging for the engineer to develop a device that continuously operated without changing its electrical behavior due to radiation. Therefore, the main objective of this study is to investigate the Single Event Effect (SEE) sensitivity by using Heavy Ion Radiation on the commercial Power MOSFET. A simulation study using Sentaurus Synopsys TCAD software for process simulation and device simulation was done. The simulation results reveal that single heavy ion radiation has affected the device structure and fluctuate the I-V characteristic of commercial Power MOSFET.
Performance analysis of ultrathin junctionless double gate vertical MOSFETsjournalBEEI
The main challenge in MOSFET minituarization is to form an ultra-shallow source/drain (S/D) junction with high doping concentration gradient, which requires an intricate S/D and channel engineering. Junctionless MOSFET configuration is an alternative solution for this issue as the junction and doping gradients is totally eliminated. A process simulation has been developed to investigate the impact of junctionless configuration on the double-gate vertical MOSFET. The result proves that the performance of junctionless double-gate vertical MOSFETs (JLDGVM) are superior to the conventional junctioned double-gate vertical MOSFETs (JDGVM). The results reveal that the drain current (ID) of the n-JLVDGM and p-JLVDGM could be tremendously enhanced by 57% and 60% respectively as the junctionless configuration was applied to the double-gate vertical MOSFET. In addition, junctionless devices also exhibit larger ION/IOFF ratio and smaller subthreshold slope compared to the junction devices, implying that the junctionless devices have better power consumption and faster switching capability.
Optimization of 14 nm double gate Bi-GFET for lower leakage currentTELKOMNIKA JOURNAL
In recent years, breakthroughs in electronics technology have resulted in upgrades in the physical properties of the metal oxide semiconductor field effect transistor (MOSFET) toward smaller sizes and improvements in both quality and performance. Hence, the growth field effect transistor (GFET) is being promoted as one of the worthy contenders due to its superior material characteristics. A 14 nm horizontal double-gate bilayer graphene FET with a high-k/metal gate is proposed, which is composed of hafnium dioxide (HfO2) and tungsten silicide (WSix) respectively. It is simulated and modelled using silvaco ATHENA and ATLAS technology computer-aided design (TCAD) tools, as well as the Taguchi L9 orthogonal array (OA). The threshold voltage (VTH) adjustment implant dose, VTH adjustment implant energy, source/drain (S/D) implant dose, and S/D implant energy have all been investigated as process parameters. While the VTH adjustment tilt angle and the S/D implant tilt angle have both been investigated as noise factors. When compared to the initial findings before optimization, the IOFF has a value of 29.579 nA/µm, indicating a significant improvement. Findings from the optimization technique demonstrate excellent device performance with an IOFF of 28.564 nA/µm, which is closer to the international technology roadmap semiconductor (ITRS) 2013 target than before
Geometric and process design of ultra-thin junctionless double gate vertical ...IJECEIAES
The junctionless MOSFET architectures appear to be attractive in realizing the Moore’s law prediction. In this paper, a comprehensive 2-D simulation on junctionless vertical double-gate MOSFET (JLDGVM) under geometric and process consideration was introduced in order to obtain excellent electrical characteristics. Geometrical designs such as channel length (Lch) and pillar thickness (Tp) were considered and the impact on the electrical performance was analyzed. The influence of doping concentration and metal gate work function (WF) were further investigated for achieving better performance. The results show that the shorter Lch can boost the drain current (ID) of n-JLDGVM and p-JLDGVM by approximately 68% and 70% respectively. The ID of the n-JLVDGM and p-JLVDGM could possibly boost up to 42% and 78% respectively as the Tp is scaled down from 11nm to 8nm. The channel doping (Nch) is also a critical parameter, affecting the electrical performance of both n-JLDGVM and p-JLDGVM in which 15% and 39% improvements are observed in their respective ID as the concentration level is increased from 1E18 to 9E18 atom/cm3. In addition, the adjustment of threshold voltage can be realized by varying the metal WF.
Simulation study of single event effects sensitivity on commercial power MOSF...journalBEEI
High-frequency semiconductor devices are key components for advanced power electronic system that require fast switching speed. Power Metal Oxide Semiconductor Field Effect Transistor (MOSFET) is the most famous electronic device that are used in much power electronic system. However, the application such as space borne, military and communication system needs Power MOSFET to withstand in radiation environments. This is very challenging for the engineer to develop a device that continuously operated without changing its electrical behavior due to radiation. Therefore, the main objective of this study is to investigate the Single Event Effect (SEE) sensitivity by using Heavy Ion Radiation on the commercial Power MOSFET. A simulation study using Sentaurus Synopsys TCAD software for process simulation and device simulation was done. The simulation results reveal that single heavy ion radiation has affected the device structure and fluctuate the I-V characteristic of commercial Power MOSFET.
Performance analysis of ultrathin junctionless double gate vertical MOSFETsjournalBEEI
The main challenge in MOSFET minituarization is to form an ultra-shallow source/drain (S/D) junction with high doping concentration gradient, which requires an intricate S/D and channel engineering. Junctionless MOSFET configuration is an alternative solution for this issue as the junction and doping gradients is totally eliminated. A process simulation has been developed to investigate the impact of junctionless configuration on the double-gate vertical MOSFET. The result proves that the performance of junctionless double-gate vertical MOSFETs (JLDGVM) are superior to the conventional junctioned double-gate vertical MOSFETs (JDGVM). The results reveal that the drain current (ID) of the n-JLVDGM and p-JLVDGM could be tremendously enhanced by 57% and 60% respectively as the junctionless configuration was applied to the double-gate vertical MOSFET. In addition, junctionless devices also exhibit larger ION/IOFF ratio and smaller subthreshold slope compared to the junction devices, implying that the junctionless devices have better power consumption and faster switching capability.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
Performance Evaluation of GaN Based Thin Film Transistor using TCAD Simulation IJECEIAES
As reported in past decades, gallium nitride as one of the most capable compound semiconductor, GaN-based high-electron mobility transistors are the focus of intense research activities in the area of high power, high-speed, and high-temperature transistors. In this paper we present a design and simulation of the GaN based thin film transistor using sentaurus TCAD for the extracting the electrical performance. The resulting GaN TFTs exhibits good electrical performance in the simulated results, including, a threshold voltage of 12-15 V, an on/off current ratio of 6.5×10 7 ~ 8.3×10 , and a subthreshold slope of 0.44V/dec. Sentaurus TCAD simulations is the tool which offers study of comprehensive behavior of semiconductor structures with ease. The simulation results of the TFT structure based on gallium nitride active channel have great prospective in the next-generation flat-panel display applications.
Performance Evaluation of GaN Based Thin Film Transistor using TCAD Simulation Yayah Zakaria
As reported in past decades, gallium nitride as one of the most capable compound semiconductor, GaN-based high-electron mobility transistors are the focus of intense research activities in the area of high power, high-speed, and high-temperature transistors. In this paper we present a design and simulation of the GaN based thin film transistor using sentaurus TCAD for
the extracting the electrical performance. The resulting GaN TFTs exhibits good electrical performance in the simulated results, including, a threshold voltage of 12-15 V, an on/off current ratio of 6.5×10 7 ~ 8.3×10 and a subthreshold slope
of 0.44V/dec. Sentaurus TCAD simulations is the tool which
offers study of comprehensive behavior of semiconductor structures with ease. The simulation results of the TFT structure based on gallium nitride active channel have great prospective in the next-generation flat-panel display applications.
Accurate leakage current models for MOSFET nanoscale devices IJECEIAES
This paper underlines a closed form of MOSFET transistor’s leakage current mechanisms in the sub 100nmparadigm.The incorporation of drain induced barrier lowering (DIBL), Gate Induced Drain Lowering (GIDL) and body effect (m) on the sub-threshold leakage (I sub ) was investigated in detail. The Band-To-Band Tunneling (I BTBT ) due to the source and Drain PN reverse junction were also modeled with a close and accurate model using a rectangular approximation method (RJA). The three types of gate leakage (I G ) were also modeled and analyzed for parasitic (I GO ), inversion channel (I GC ), and gate substrate (I GB ). In addition, the leakage resources due to the aggressive reduction in the oxide thickness (<5nm) have been investigated. Simulation results using HSPICE exhibits a tremendous agreement with the BSIM4 model. The dominant value of the sub-threshold leakage was due to the DIBL and GIDL effects. Various recommendations regarding minimizing the leakage current at both device level and the circuit level were suggested at the end of this paper.
LINEARITY AND ANALOG PERFORMANCE ANALYSIS OF DOUBLE GATE TUNNEL FET: EFFECT O...VLSICS Design
The linearity and analog performance of a Silicon Double Gate Tunnel Field Effect Transistor (DG-TFET) is investigated and the impact of elevated temperature on the device performance degradation has been studied. The impact on the device performance due to the rise in temperature and a gate stack (GS) architecture has also been investigated for the case of Silicon DG-MOSFET and a comparison with DGTFET is made. The parameters overning the analog performance and linearity have been studied, and high frequency simulations are carried out to determine the cut-off frequency of the device and its temperature dependence.
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology
Analysis of analog and RF behaviors in junctionless double gate vertical MOSFETjournalBEEI
The prime obstacle in continuing the transistor’s scaling is to maintain ultra-shallow source/drain (S/D) junctions with high doping concentration gradient, which definitely demands an advanced and complicated S/D and channel engineering. Junctionless transistor configuration has been found to be an alternative device structure in which the junction and doping gradients could be totally eliminated, thus simplifying the fabrication process. In this paper, a process simulation has been performed to study the impact of junctionless configuration on the analog and RF behaviors of double-gate vertical MOSFET. The result proves that the performance of n-channel junctionless double-gate vertical MOSFET (n-JLDGVM) is slightly better than the junction double-gate vertical MOSFET (n-JDGVM). Junctionless device exhibits better analog behaviors as the transconductance (gm) is increased by approximately 4%. In term of RF behaviors, the junctionless device exhibits 3.4% and 7% higher cut-off frequency (fT) and gain band-width product (GBW) respectively over the junction device.
DC performance analysis of a 20nm gate length n-type Silicon GAA junctionless...IJECEIAES
With integrated circuit scales in the 22-nm regime, conventional planar MOSFETs have approached the limit of their potential performance. To overcome short channel effects 'SCEs' that appears for deeply scaled MOSFETs beyond 10nm technology node many new device structures and channel materials have been proposed. Among these devices such as Gate-all-around FET. Recentely, junctionless GAA MOSFETs JL-GAA MOSFETs have attracted much attention since the junctionless MOSFET has been presented. In this paper, DC characteristics of an n-type JL-GAA MOSFET are presented using a 3-D quantum transport model. This new generation device is conceived with the same doping concentration level in its channel source/drain allowing to reduce fabrication complexity. The performance of our 3D JL-GAA structure with a 20nm gate length and a rectangular cross section have been obtained using SILVACO TCAD tools allowing also to study short channel effects. Our device reveals a favorable on/off current ratio and better SCE characteristics compared to an inversionmode GAA transistor. Our device reveals a threshold voltage of 0.55 V, a sub-threshold slope of 63mV / decade which approaches the ideal value, an Ion/Ioff ratio of 10e + 10 value and a drain induced barrier lowring (DIBL) value of 98mV/V.
Optimization of Empirical Modelling of Advanced Highly Strained In 0.7 Ga 0.3...IJECEIAES
An optimized empirical modelling for a 0.25µm gate length of highly strained channel of an InP-based pseudomorphic high electron mobility transistor (pHEMT) using InGaAs–InAlAs material systems is presented. An accurate procedure for extraction is described and tested using the pHEMT measured dataset of I-V characteristics and related multi-bias s-parameters over 20GHz frequency range. The extraction of linear and nonlinear parameters from the small signal and large signal pHEMT equivalent model are performed in ADS. The optimized DC and S-parameter model for the pHEMT device provides a basis for active device selection in the MMIC low noise amplifier circuit designs.
Operational transconductance amplifier-based comparator for high frequency a...IJECEIAES
Fin field-effect transistor (FinFET) based analog circuits are gaining importance over metal oxide semiconductor field effect transistor (MOSFET) based circuits with stability and high frequency operations. Comparator that forms the sub block of most of the analog circuits is designed using operational transconductance amplifier (OTA). The OTA is designed using new design procedures and the comparator circuit is designed integrating the sub circuits with OTA. The building blocks of the comparator design such as input level shifter, differential pair with cascode stage and class AB amplifier for output swing are designed and integrated. Folded cascode circuit is used in the feedback path to maintain the common mode input value to a constant, so that the differential pair amplifies the differential signal. The gain of the comparator is achieved to be greater than 100 dB, with phase margin of 65°, common mode rejection ratio (CMRR) of above 70 dB and output swing from rail to rail. The circuit provides unity gain bandwidth of 5 GHz and is suitable for high sampling rate data converter circuits.
Electrical characterization of si nanowire GAA-TFET based on dimensions downs...IJECEIAES
This research paper explains the effect of the dimensions of Gate-all-around Si nanowire tunneling field effect transistor (GAA Si-NW TFET) on ON/OFF current ratio, drain induces barrier lowering (DIBL), sub-threshold swing (SS), and threshold voltage (V T ). These parameters are critical factors of the characteristics of tunnel field effect transistors. The Silvaco TCAD has been used to study the electrical characteristics of Si-NW TFET. Output (gate voltage-drain current) characteristics with channel dimensions were simulated. Results show that 50nm long nanowires with 9nm-18nm diameter and 3nm oxide thickness tend to have the best nanowire tunnel field effect transistor (Si-NW TFET) characteristics.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
Performance Evaluation of GaN Based Thin Film Transistor using TCAD Simulation IJECEIAES
As reported in past decades, gallium nitride as one of the most capable compound semiconductor, GaN-based high-electron mobility transistors are the focus of intense research activities in the area of high power, high-speed, and high-temperature transistors. In this paper we present a design and simulation of the GaN based thin film transistor using sentaurus TCAD for the extracting the electrical performance. The resulting GaN TFTs exhibits good electrical performance in the simulated results, including, a threshold voltage of 12-15 V, an on/off current ratio of 6.5×10 7 ~ 8.3×10 , and a subthreshold slope of 0.44V/dec. Sentaurus TCAD simulations is the tool which offers study of comprehensive behavior of semiconductor structures with ease. The simulation results of the TFT structure based on gallium nitride active channel have great prospective in the next-generation flat-panel display applications.
Performance Evaluation of GaN Based Thin Film Transistor using TCAD Simulation Yayah Zakaria
As reported in past decades, gallium nitride as one of the most capable compound semiconductor, GaN-based high-electron mobility transistors are the focus of intense research activities in the area of high power, high-speed, and high-temperature transistors. In this paper we present a design and simulation of the GaN based thin film transistor using sentaurus TCAD for
the extracting the electrical performance. The resulting GaN TFTs exhibits good electrical performance in the simulated results, including, a threshold voltage of 12-15 V, an on/off current ratio of 6.5×10 7 ~ 8.3×10 and a subthreshold slope
of 0.44V/dec. Sentaurus TCAD simulations is the tool which
offers study of comprehensive behavior of semiconductor structures with ease. The simulation results of the TFT structure based on gallium nitride active channel have great prospective in the next-generation flat-panel display applications.
Accurate leakage current models for MOSFET nanoscale devices IJECEIAES
This paper underlines a closed form of MOSFET transistor’s leakage current mechanisms in the sub 100nmparadigm.The incorporation of drain induced barrier lowering (DIBL), Gate Induced Drain Lowering (GIDL) and body effect (m) on the sub-threshold leakage (I sub ) was investigated in detail. The Band-To-Band Tunneling (I BTBT ) due to the source and Drain PN reverse junction were also modeled with a close and accurate model using a rectangular approximation method (RJA). The three types of gate leakage (I G ) were also modeled and analyzed for parasitic (I GO ), inversion channel (I GC ), and gate substrate (I GB ). In addition, the leakage resources due to the aggressive reduction in the oxide thickness (<5nm) have been investigated. Simulation results using HSPICE exhibits a tremendous agreement with the BSIM4 model. The dominant value of the sub-threshold leakage was due to the DIBL and GIDL effects. Various recommendations regarding minimizing the leakage current at both device level and the circuit level were suggested at the end of this paper.
LINEARITY AND ANALOG PERFORMANCE ANALYSIS OF DOUBLE GATE TUNNEL FET: EFFECT O...VLSICS Design
The linearity and analog performance of a Silicon Double Gate Tunnel Field Effect Transistor (DG-TFET) is investigated and the impact of elevated temperature on the device performance degradation has been studied. The impact on the device performance due to the rise in temperature and a gate stack (GS) architecture has also been investigated for the case of Silicon DG-MOSFET and a comparison with DGTFET is made. The parameters overning the analog performance and linearity have been studied, and high frequency simulations are carried out to determine the cut-off frequency of the device and its temperature dependence.
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology
Analysis of analog and RF behaviors in junctionless double gate vertical MOSFETjournalBEEI
The prime obstacle in continuing the transistor’s scaling is to maintain ultra-shallow source/drain (S/D) junctions with high doping concentration gradient, which definitely demands an advanced and complicated S/D and channel engineering. Junctionless transistor configuration has been found to be an alternative device structure in which the junction and doping gradients could be totally eliminated, thus simplifying the fabrication process. In this paper, a process simulation has been performed to study the impact of junctionless configuration on the analog and RF behaviors of double-gate vertical MOSFET. The result proves that the performance of n-channel junctionless double-gate vertical MOSFET (n-JLDGVM) is slightly better than the junction double-gate vertical MOSFET (n-JDGVM). Junctionless device exhibits better analog behaviors as the transconductance (gm) is increased by approximately 4%. In term of RF behaviors, the junctionless device exhibits 3.4% and 7% higher cut-off frequency (fT) and gain band-width product (GBW) respectively over the junction device.
DC performance analysis of a 20nm gate length n-type Silicon GAA junctionless...IJECEIAES
With integrated circuit scales in the 22-nm regime, conventional planar MOSFETs have approached the limit of their potential performance. To overcome short channel effects 'SCEs' that appears for deeply scaled MOSFETs beyond 10nm technology node many new device structures and channel materials have been proposed. Among these devices such as Gate-all-around FET. Recentely, junctionless GAA MOSFETs JL-GAA MOSFETs have attracted much attention since the junctionless MOSFET has been presented. In this paper, DC characteristics of an n-type JL-GAA MOSFET are presented using a 3-D quantum transport model. This new generation device is conceived with the same doping concentration level in its channel source/drain allowing to reduce fabrication complexity. The performance of our 3D JL-GAA structure with a 20nm gate length and a rectangular cross section have been obtained using SILVACO TCAD tools allowing also to study short channel effects. Our device reveals a favorable on/off current ratio and better SCE characteristics compared to an inversionmode GAA transistor. Our device reveals a threshold voltage of 0.55 V, a sub-threshold slope of 63mV / decade which approaches the ideal value, an Ion/Ioff ratio of 10e + 10 value and a drain induced barrier lowring (DIBL) value of 98mV/V.
Optimization of Empirical Modelling of Advanced Highly Strained In 0.7 Ga 0.3...IJECEIAES
An optimized empirical modelling for a 0.25µm gate length of highly strained channel of an InP-based pseudomorphic high electron mobility transistor (pHEMT) using InGaAs–InAlAs material systems is presented. An accurate procedure for extraction is described and tested using the pHEMT measured dataset of I-V characteristics and related multi-bias s-parameters over 20GHz frequency range. The extraction of linear and nonlinear parameters from the small signal and large signal pHEMT equivalent model are performed in ADS. The optimized DC and S-parameter model for the pHEMT device provides a basis for active device selection in the MMIC low noise amplifier circuit designs.
Operational transconductance amplifier-based comparator for high frequency a...IJECEIAES
Fin field-effect transistor (FinFET) based analog circuits are gaining importance over metal oxide semiconductor field effect transistor (MOSFET) based circuits with stability and high frequency operations. Comparator that forms the sub block of most of the analog circuits is designed using operational transconductance amplifier (OTA). The OTA is designed using new design procedures and the comparator circuit is designed integrating the sub circuits with OTA. The building blocks of the comparator design such as input level shifter, differential pair with cascode stage and class AB amplifier for output swing are designed and integrated. Folded cascode circuit is used in the feedback path to maintain the common mode input value to a constant, so that the differential pair amplifies the differential signal. The gain of the comparator is achieved to be greater than 100 dB, with phase margin of 65°, common mode rejection ratio (CMRR) of above 70 dB and output swing from rail to rail. The circuit provides unity gain bandwidth of 5 GHz and is suitable for high sampling rate data converter circuits.
Electrical characterization of si nanowire GAA-TFET based on dimensions downs...IJECEIAES
This research paper explains the effect of the dimensions of Gate-all-around Si nanowire tunneling field effect transistor (GAA Si-NW TFET) on ON/OFF current ratio, drain induces barrier lowering (DIBL), sub-threshold swing (SS), and threshold voltage (V T ). These parameters are critical factors of the characteristics of tunnel field effect transistors. The Silvaco TCAD has been used to study the electrical characteristics of Si-NW TFET. Output (gate voltage-drain current) characteristics with channel dimensions were simulated. Results show that 50nm long nanowires with 9nm-18nm diameter and 3nm oxide thickness tend to have the best nanowire tunnel field effect transistor (Si-NW TFET) characteristics.
Sachpazis:Terzaghi Bearing Capacity Estimation in simple terms with Calculati...Dr.Costas Sachpazis
Terzaghi's soil bearing capacity theory, developed by Karl Terzaghi, is a fundamental principle in geotechnical engineering used to determine the bearing capacity of shallow foundations. This theory provides a method to calculate the ultimate bearing capacity of soil, which is the maximum load per unit area that the soil can support without undergoing shear failure. The Calculation HTML Code included.
Forklift Classes Overview by Intella PartsIntella Parts
Discover the different forklift classes and their specific applications. Learn how to choose the right forklift for your needs to ensure safety, efficiency, and compliance in your operations.
For more technical information, visit our website https://intellaparts.com
HEAP SORT ILLUSTRATED WITH HEAPIFY, BUILD HEAP FOR DYNAMIC ARRAYS.
Heap sort is a comparison-based sorting technique based on Binary Heap data structure. It is similar to the selection sort where we first find the minimum element and place the minimum element at the beginning. Repeat the same process for the remaining elements.
NUMERICAL SIMULATIONS OF HEAT AND MASS TRANSFER IN CONDENSING HEAT EXCHANGERS...ssuser7dcef0
Power plants release a large amount of water vapor into the
atmosphere through the stack. The flue gas can be a potential
source for obtaining much needed cooling water for a power
plant. If a power plant could recover and reuse a portion of this
moisture, it could reduce its total cooling water intake
requirement. One of the most practical way to recover water
from flue gas is to use a condensing heat exchanger. The power
plant could also recover latent heat due to condensation as well
as sensible heat due to lowering the flue gas exit temperature.
Additionally, harmful acids released from the stack can be
reduced in a condensing heat exchanger by acid condensation. reduced in a condensing heat exchanger by acid condensation.
Condensation of vapors in flue gas is a complicated
phenomenon since heat and mass transfer of water vapor and
various acids simultaneously occur in the presence of noncondensable
gases such as nitrogen and oxygen. Design of a
condenser depends on the knowledge and understanding of the
heat and mass transfer processes. A computer program for
numerical simulations of water (H2O) and sulfuric acid (H2SO4)
condensation in a flue gas condensing heat exchanger was
developed using MATLAB. Governing equations based on
mass and energy balances for the system were derived to
predict variables such as flue gas exit temperature, cooling
water outlet temperature, mole fraction and condensation rates
of water and sulfuric acid vapors. The equations were solved
using an iterative solution technique with calculations of heat
and mass transfer coefficients and physical properties.
Hierarchical Digital Twin of a Naval Power SystemKerry Sado
A hierarchical digital twin of a Naval DC power system has been developed and experimentally verified. Similar to other state-of-the-art digital twins, this technology creates a digital replica of the physical system executed in real-time or faster, which can modify hardware controls. However, its advantage stems from distributing computational efforts by utilizing a hierarchical structure composed of lower-level digital twin blocks and a higher-level system digital twin. Each digital twin block is associated with a physical subsystem of the hardware and communicates with a singular system digital twin, which creates a system-level response. By extracting information from each level of the hierarchy, power system controls of the hardware were reconfigured autonomously. This hierarchical digital twin development offers several advantages over other digital twins, particularly in the field of naval power systems. The hierarchical structure allows for greater computational efficiency and scalability while the ability to autonomously reconfigure hardware controls offers increased flexibility and responsiveness. The hierarchical decomposition and models utilized were well aligned with the physical twin, as indicated by the maximum deviations between the developed digital twin hierarchy and the hardware.