1. The document discusses gain flattening in Erbium Doped Fiber Amplifiers (EDFAs), which are widely used in optical communication systems but have an intrinsic non-uniform gain spectrum.
2. EDFAs are discussed as the key optical amplifiers used, but they exhibit gain peaking around 1530nm and a useful bandwidth of less than 10nm, limiting the number of wavelength channels that can be used.
3. Various gain flattening techniques for EDFAs are discussed, including using optical filters with loss profiles matching the gain spectrum to produce a flat overall gain.
These are the slides of the talk "Putting the citizens at the center of the network: Cell-free architectures" that I delivered at the IEEE 5G Summit held in Montreal today!
Frequency-independent (FI) antennas are radiating structures capable of maintaining consistent impedance and pattern characteristics over multiple-decade bandwidths. Their finite size limits the lowest frequency of operation, and the finite precision of the center region bounds the highest frequency of operation.
These are the slides of the talk "Putting the citizens at the center of the network: Cell-free architectures" that I delivered at the IEEE 5G Summit held in Montreal today!
Frequency-independent (FI) antennas are radiating structures capable of maintaining consistent impedance and pattern characteristics over multiple-decade bandwidths. Their finite size limits the lowest frequency of operation, and the finite precision of the center region bounds the highest frequency of operation.
Study of Planar Inverted - F Antenna (PIFA) for mobile devices Naveen Kumar
A brief study of planar inverted-F antenna is given. Basic structure of PIFA is discussed and effect of various parameters is explained. Techniques to improve bandwidth coverage by the antenna are also discussed.
In-building Solution (IBS) / Distributed Antenna System (DAS)
Small Cell Coverage within building premises
Signal is restricted inside the building
Antenna installed inside the building
Low Transmit Power of Antenna
Smaller Antenna size
The attached narrated power point presentation attempts to explain the working principle, types, classifications, merits, demerits, applications,safety and deployment issues related to Raman Amplifiers. The material will be useful for KTU final year B Tech students who prepare for the subject EC 405, Optical Communications.
Introducing our 5G Platform for the first movers in 5G, the first completely end-to-end solution that combines core and radio solutions in 5G to enable new opportunities and use cases
Setting off the 5G Advanced evolution with 3GPP Release 18Qualcomm Research
In December 2021, 3GPP has reached a consensus on the scope of 5G NR Release 18. This is a significant milestone marking the beginning of 5G Advanced — the second wave of wireless innovations that will fulfill the 5G vision. Release 18 will build on the solid foundation set by Releases 15, 16, and 17, and it sets the longer-term evolution direction of 5G and beyond. This release will encompass a wide range of new and enhancement projects, ranging from improved MIMO and application of AI/ML-enabled air interface to extended reality optimizations and broader IoT support.
Microwave backhaul plays an important role in providing a good user experience and overall network performance. The backhaul capacity needed per base station differs substantially, depending on target data rates and population density.
Microwave backhaul technology is able to handle 100 percent of all radio access sites’ capacity needs. This is true for today as well as in 2020, when it will evolve to support multi-gigabit capacities in traditional frequency bands and beyond 10 gigabits in the millimeter wave.
Capacity planning(CP) determines operational expenditure, capital expenditure and long-term performance of the system hence it is the most important phase in the life cycle of a cellular system. For the past three decades, capacity planning problems have studied for all generations of the cellular system. So, to increase the capacity of the network in future we focus on small cells of cell structure. Cellular network includes the variety of different cell sizes and types, heterogeneous networks, control, and data plane split architectures, coordinated multipoint, massive multiple inputs multiple outputs.
The objective of this presentation is to focus on traditional deployment reviews and identify future opportunities, challenges, and trends in detail. More specifically we investigate the future capacity planning by reviewing the CP process including its objective input and output parameter to an optimization process and the CP phases.
Unit_5_Lecture-1_introduction, types, parameters of transmission linesMd Khaja Mohiddin
In this video, you will able to understand the definition as well as the concept of transmission lines along with its types relevant to various applications. Additionally, you will able to have an idea about various transmission line parameters along with its formula corresponding to each type.
Study of Planar Inverted - F Antenna (PIFA) for mobile devices Naveen Kumar
A brief study of planar inverted-F antenna is given. Basic structure of PIFA is discussed and effect of various parameters is explained. Techniques to improve bandwidth coverage by the antenna are also discussed.
In-building Solution (IBS) / Distributed Antenna System (DAS)
Small Cell Coverage within building premises
Signal is restricted inside the building
Antenna installed inside the building
Low Transmit Power of Antenna
Smaller Antenna size
The attached narrated power point presentation attempts to explain the working principle, types, classifications, merits, demerits, applications,safety and deployment issues related to Raman Amplifiers. The material will be useful for KTU final year B Tech students who prepare for the subject EC 405, Optical Communications.
Introducing our 5G Platform for the first movers in 5G, the first completely end-to-end solution that combines core and radio solutions in 5G to enable new opportunities and use cases
Setting off the 5G Advanced evolution with 3GPP Release 18Qualcomm Research
In December 2021, 3GPP has reached a consensus on the scope of 5G NR Release 18. This is a significant milestone marking the beginning of 5G Advanced — the second wave of wireless innovations that will fulfill the 5G vision. Release 18 will build on the solid foundation set by Releases 15, 16, and 17, and it sets the longer-term evolution direction of 5G and beyond. This release will encompass a wide range of new and enhancement projects, ranging from improved MIMO and application of AI/ML-enabled air interface to extended reality optimizations and broader IoT support.
Microwave backhaul plays an important role in providing a good user experience and overall network performance. The backhaul capacity needed per base station differs substantially, depending on target data rates and population density.
Microwave backhaul technology is able to handle 100 percent of all radio access sites’ capacity needs. This is true for today as well as in 2020, when it will evolve to support multi-gigabit capacities in traditional frequency bands and beyond 10 gigabits in the millimeter wave.
Capacity planning(CP) determines operational expenditure, capital expenditure and long-term performance of the system hence it is the most important phase in the life cycle of a cellular system. For the past three decades, capacity planning problems have studied for all generations of the cellular system. So, to increase the capacity of the network in future we focus on small cells of cell structure. Cellular network includes the variety of different cell sizes and types, heterogeneous networks, control, and data plane split architectures, coordinated multipoint, massive multiple inputs multiple outputs.
The objective of this presentation is to focus on traditional deployment reviews and identify future opportunities, challenges, and trends in detail. More specifically we investigate the future capacity planning by reviewing the CP process including its objective input and output parameter to an optimization process and the CP phases.
Unit_5_Lecture-1_introduction, types, parameters of transmission linesMd Khaja Mohiddin
In this video, you will able to understand the definition as well as the concept of transmission lines along with its types relevant to various applications. Additionally, you will able to have an idea about various transmission line parameters along with its formula corresponding to each type.
An Overview of EDFA Gain Flattening by Using Hybrid AmplifierIJEEE
Data communication systems are increasingly engrossing optical fiber communication system as the transmission paths for the information, the information is in the form of light pulses sending from one place to another through the optical fiber. Several types of optical amplifiers have been developed in optical fiber communication system to amplify the optical signals. The erbium doped fiber amplifier is one of the optical fiber amplifiers which are used for long distance communication. The most significant points in any optical amplifier design are gain and noise figure. They are connected to one another. The other optical amplifier, Raman amplifier has wide gain bandwidth. The EDFA gain spectrum has variations over 1536 to 1552 nm, therefore the gain flattening is a research issue in recent years with the development of high capacity DWDM. The gain variation becomes a problem as the number of channels increases. The gain of EDFA depends on large number of device parameters such as, Erbium ion concentration, amplifier length, core radius, pump power. Raman amplifiers can be combined with EDFAs to expand the optical gain flattened bandwidth. This paper focuses on different methods used for the gain flattening.
Performance Improvement for Hybrid L-band Remote Erbium Doped Fiber Amplifier...IJECEIAES
We have demonstrated the performance improvement of L-band hybrid remote Erbium-doped fiber amplifier by introducing a phase modulator to suppress the stimulated Brilloiun scattering (SBS) effect in the transmission. The transmission gain has improved by 12.65dB while the noise figure has reduced by 47.1dB when 0dBm signal power is generated at 1590.05nm wavelength. Furthermore, the optical signal-to-noise ratio has improved from 7.81dB to 29.72dB when the signal power is varied from -30dBm to 0dBm. By implementing a phase modulator to the input signal somehow able to produce better performance regarding gain, noise figure and optical signalto-noise ratio, especially at the higher signal power as the gain, has been transferred to the Stokes signal and the amplified signal.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
Power Transient Response of EDFA as a function of Wavelength in the scenario ...ijsrd.com
In this paper power transient is investigated as function of add/drop wavelength and surviving channel wavelength. We have reported that power excursions varies with different wavelength allocations of the add/drop channels. Transient response is reduced by 73.39% in case when add/drop channels are taken in L band instead of C band. Also power transient response is calculated as a function of wavelengths of surviving channel. It has been observed that at higher wavelengths power excursions are less than at shorter wavelengths of C band.
STUDIED ON A MULTICLADDED ERBIUM DOPED DISPERSION COMPENSATING FIBER AMPLIFIERcscpconf
Erbium doped fiber amplifiers (EDFAs) are the essential components of a highly efficient, long distance optical data link.Their design has been refined to give better performance parameters.A novel design approach for erbium-doped fiber amplifiers is proposed based on Matlab and Fortran 77 Programming.In this paper, a combination of fiber intensity distribution, pump and signal power, optimum length and maximum gain are taken into account as objective function
and the results are presented for different core radius, fiber length, pump power and signal power. Dispersion compensating fibers (DCFs) which possess negative dispersion coefficient
equal to or greater than this 17ps/km-nm can be used to overcome this drawback. In order to upgrade the present long haul fiber optic communication system, comprising of CSFs, a
combination of EDFAs and DCFs would be the most feasible choice to compensate the dispersion as well as the loss.
In pursuit of high transmission capacity, people have been tried many ways. For
example, they pave more cables or use the TDM (time domain multiplexer) to
improve the transmission capacity. But in these traditional ways, signals could
become weaker in power through the fiber link. And the further they are transmitted,
the weaker the signals will be until they can not be detected. With the advanced of
technology, optical amplifier which is a better solution to improve the transmission
capacity came around. It can strengthen the attenuated signals and even can bring
them back to the original level. And now it is mainly applied in DWDM technology
so that DWDM technology can support long-haul transmission.
The scope of this paper is to analyze the performance of HG_EDFA (High Gain Erbium Doped Fiber Amplifier) and LN_EYCDFA (Less ASE Noise erbium-ytterbium co-doped fiber amplifier) using single pumping with the wavelength of 980nm by the various parameters like Gain, forward output signal power and forward and backward ASE (Amplified spontaneous Emission) noise power. This Paper describes the simulation models of HG_EDFA is connected with an input of (DMLaser1) direct modulated laser source and the performance was analyzed with the parameters were measured and the values are tabulated and plotted and compared with LN_EYCDFA. The simulation model consists of input source 1mw with wavelength (1550nm), pumping CW Laser source with wavelength 980nm and Filter. The resulting models were accurately represents Gain and optimized output signal power. Simulation results shows that by choosing careful fiber length 20m and pump power 1mw in single pumping gives ASE noise 0.0025mw in HG_EDFA and 12X10-14mw in LN_EYCDFA.
Attenuation is
the reduction of signal strength or light power over the length of
the light-carrying medium. As the light signal travels down the fiber,
it losses power or attenuates.
Similar to 12 gain flattening in erbium doped fiber amplifier based optical communication a review (20)
What is the TDS Return Filing Due Date for FY 2024-25.pdfseoforlegalpillers
It is crucial for the taxpayers to understand about the TDS Return Filing Due Date, so that they can fulfill your TDS obligations efficiently. Taxpayers can avoid penalties by sticking to the deadlines and by accurate filing of TDS. Timely filing of TDS will make sure about the availability of tax credits. You can also seek the professional guidance of experts like Legal Pillers for timely filing of the TDS Return.
Enterprise Excellence is Inclusive Excellence.pdfKaiNexus
Enterprise excellence and inclusive excellence are closely linked, and real-world challenges have shown that both are essential to the success of any organization. To achieve enterprise excellence, organizations must focus on improving their operations and processes while creating an inclusive environment that engages everyone. In this interactive session, the facilitator will highlight commonly established business practices and how they limit our ability to engage everyone every day. More importantly, though, participants will likely gain increased awareness of what we can do differently to maximize enterprise excellence through deliberate inclusion.
What is Enterprise Excellence?
Enterprise Excellence is a holistic approach that's aimed at achieving world-class performance across all aspects of the organization.
What might I learn?
A way to engage all in creating Inclusive Excellence. Lessons from the US military and their parallels to the story of Harry Potter. How belt systems and CI teams can destroy inclusive practices. How leadership language invites people to the party. There are three things leaders can do to engage everyone every day: maximizing psychological safety to create environments where folks learn, contribute, and challenge the status quo.
Who might benefit? Anyone and everyone leading folks from the shop floor to top floor.
Dr. William Harvey is a seasoned Operations Leader with extensive experience in chemical processing, manufacturing, and operations management. At Michelman, he currently oversees multiple sites, leading teams in strategic planning and coaching/practicing continuous improvement. William is set to start his eighth year of teaching at the University of Cincinnati where he teaches marketing, finance, and management. William holds various certifications in change management, quality, leadership, operational excellence, team building, and DiSC, among others.
The world of search engine optimization (SEO) is buzzing with discussions after Google confirmed that around 2,500 leaked internal documents related to its Search feature are indeed authentic. The revelation has sparked significant concerns within the SEO community. The leaked documents were initially reported by SEO experts Rand Fishkin and Mike King, igniting widespread analysis and discourse. For More Info:- https://news.arihantwebtech.com/search-disrupted-googles-leaked-documents-rock-the-seo-world/
"𝑩𝑬𝑮𝑼𝑵 𝑾𝑰𝑻𝑯 𝑻𝑱 𝑰𝑺 𝑯𝑨𝑳𝑭 𝑫𝑶𝑵𝑬"
𝐓𝐉 𝐂𝐨𝐦𝐬 (𝐓𝐉 𝐂𝐨𝐦𝐦𝐮𝐧𝐢𝐜𝐚𝐭𝐢𝐨𝐧𝐬) is a professional event agency that includes experts in the event-organizing market in Vietnam, Korea, and ASEAN countries. We provide unlimited types of events from Music concerts, Fan meetings, and Culture festivals to Corporate events, Internal company events, Golf tournaments, MICE events, and Exhibitions.
𝐓𝐉 𝐂𝐨𝐦𝐬 provides unlimited package services including such as Event organizing, Event planning, Event production, Manpower, PR marketing, Design 2D/3D, VIP protocols, Interpreter agency, etc.
Sports events - Golf competitions/billiards competitions/company sports events: dynamic and challenging
⭐ 𝐅𝐞𝐚𝐭𝐮𝐫𝐞𝐝 𝐩𝐫𝐨𝐣𝐞𝐜𝐭𝐬:
➢ 2024 BAEKHYUN [Lonsdaleite] IN HO CHI MINH
➢ SUPER JUNIOR-L.S.S. THE SHOW : Th3ee Guys in HO CHI MINH
➢FreenBecky 1st Fan Meeting in Vietnam
➢CHILDREN ART EXHIBITION 2024: BEYOND BARRIERS
➢ WOW K-Music Festival 2023
➢ Winner [CROSS] Tour in HCM
➢ Super Show 9 in HCM with Super Junior
➢ HCMC - Gyeongsangbuk-do Culture and Tourism Festival
➢ Korean Vietnam Partnership - Fair with LG
➢ Korean President visits Samsung Electronics R&D Center
➢ Vietnam Food Expo with Lotte Wellfood
"𝐄𝐯𝐞𝐫𝐲 𝐞𝐯𝐞𝐧𝐭 𝐢𝐬 𝐚 𝐬𝐭𝐨𝐫𝐲, 𝐚 𝐬𝐩𝐞𝐜𝐢𝐚𝐥 𝐣𝐨𝐮𝐫𝐧𝐞𝐲. 𝐖𝐞 𝐚𝐥𝐰𝐚𝐲𝐬 𝐛𝐞𝐥𝐢𝐞𝐯𝐞 𝐭𝐡𝐚𝐭 𝐬𝐡𝐨𝐫𝐭𝐥𝐲 𝐲𝐨𝐮 𝐰𝐢𝐥𝐥 𝐛𝐞 𝐚 𝐩𝐚𝐫𝐭 𝐨𝐟 𝐨𝐮𝐫 𝐬𝐭𝐨𝐫𝐢𝐞𝐬."
Taurus Zodiac Sign_ Personality Traits and Sign Dates.pptxmy Pandit
Explore the world of the Taurus zodiac sign. Learn about their stability, determination, and appreciation for beauty. Discover how Taureans' grounded nature and hardworking mindset define their unique personality.
Putting the SPARK into Virtual Training.pptxCynthia Clay
This 60-minute webinar, sponsored by Adobe, was delivered for the Training Mag Network. It explored the five elements of SPARK: Storytelling, Purpose, Action, Relationships, and Kudos. Knowing how to tell a well-structured story is key to building long-term memory. Stating a clear purpose that doesn't take away from the discovery learning process is critical. Ensuring that people move from theory to practical application is imperative. Creating strong social learning is the key to commitment and engagement. Validating and affirming participants' comments is the way to create a positive learning environment.
RMD24 | Debunking the non-endemic revenue myth Marvin Vacquier Droop | First ...BBPMedia1
Marvin neemt je in deze presentatie mee in de voordelen van non-endemic advertising op retail media netwerken. Hij brengt ook de uitdagingen in beeld die de markt op dit moment heeft op het gebied van retail media voor niet-leveranciers.
Retail media wordt gezien als het nieuwe advertising-medium en ook mediabureaus richten massaal retail media-afdelingen op. Merken die niet in de betreffende winkel liggen staan ook nog niet in de rij om op de retail media netwerken te adverteren. Marvin belicht de uitdagingen die er zijn om echt aansluiting te vinden op die markt van non-endemic advertising.
Falcon stands out as a top-tier P2P Invoice Discounting platform in India, bridging esteemed blue-chip companies and eager investors. Our goal is to transform the investment landscape in India by establishing a comprehensive destination for borrowers and investors with diverse profiles and needs, all while minimizing risk. What sets Falcon apart is the elimination of intermediaries such as commercial banks and depository institutions, allowing investors to enjoy higher yields.
Memorandum Of Association Constitution of Company.pptseri bangash
www.seribangash.com
A Memorandum of Association (MOA) is a legal document that outlines the fundamental principles and objectives upon which a company operates. It serves as the company's charter or constitution and defines the scope of its activities. Here's a detailed note on the MOA:
Contents of Memorandum of Association:
Name Clause: This clause states the name of the company, which should end with words like "Limited" or "Ltd." for a public limited company and "Private Limited" or "Pvt. Ltd." for a private limited company.
https://seribangash.com/article-of-association-is-legal-doc-of-company/
Registered Office Clause: It specifies the location where the company's registered office is situated. This office is where all official communications and notices are sent.
Objective Clause: This clause delineates the main objectives for which the company is formed. It's important to define these objectives clearly, as the company cannot undertake activities beyond those mentioned in this clause.
www.seribangash.com
Liability Clause: It outlines the extent of liability of the company's members. In the case of companies limited by shares, the liability of members is limited to the amount unpaid on their shares. For companies limited by guarantee, members' liability is limited to the amount they undertake to contribute if the company is wound up.
https://seribangash.com/promotors-is-person-conceived-formation-company/
Capital Clause: This clause specifies the authorized capital of the company, i.e., the maximum amount of share capital the company is authorized to issue. It also mentions the division of this capital into shares and their respective nominal value.
Association Clause: It simply states that the subscribers wish to form a company and agree to become members of it, in accordance with the terms of the MOA.
Importance of Memorandum of Association:
Legal Requirement: The MOA is a legal requirement for the formation of a company. It must be filed with the Registrar of Companies during the incorporation process.
Constitutional Document: It serves as the company's constitutional document, defining its scope, powers, and limitations.
Protection of Members: It protects the interests of the company's members by clearly defining the objectives and limiting their liability.
External Communication: It provides clarity to external parties, such as investors, creditors, and regulatory authorities, regarding the company's objectives and powers.
https://seribangash.com/difference-public-and-private-company-law/
Binding Authority: The company and its members are bound by the provisions of the MOA. Any action taken beyond its scope may be considered ultra vires (beyond the powers) of the company and therefore void.
Amendment of MOA:
While the MOA lays down the company's fundamental principles, it is not entirely immutable. It can be amended, but only under specific circumstances and in compliance with legal procedures. Amendments typically require shareholder
Personal Brand Statement:
As an Army veteran dedicated to lifelong learning, I bring a disciplined, strategic mindset to my pursuits. I am constantly expanding my knowledge to innovate and lead effectively. My journey is driven by a commitment to excellence, and to make a meaningful impact in the world.
Remote sensing and monitoring are changing the mining industry for the better. These are providing innovative solutions to long-standing challenges. Those related to exploration, extraction, and overall environmental management by mining technology companies Odisha. These technologies make use of satellite imaging, aerial photography and sensors to collect data that might be inaccessible or from hazardous locations. With the use of this technology, mining operations are becoming increasingly efficient. Let us gain more insight into the key aspects associated with remote sensing and monitoring when it comes to mining.
As a business owner in Delaware, staying on top of your tax obligations is paramount, especially with the annual deadline for Delaware Franchise Tax looming on March 1. One such obligation is the annual Delaware Franchise Tax, which serves as a crucial requirement for maintaining your company’s legal standing within the state. While the prospect of handling tax matters may seem daunting, rest assured that the process can be straightforward with the right guidance. In this comprehensive guide, we’ll walk you through the steps of filing your Delaware Franchise Tax and provide insights to help you navigate the process effectively.
Filing Your Delaware Franchise Tax A Detailed Guide
12 gain flattening in erbium doped fiber amplifier based optical communication a review
1. N SINDHU and P. K. SHAFEENA 50
International Journal of Emerging Trends in Electrical and Electronics (IJETEE) Vol. 1, Issue. 2, March-2013.
Gain flattening in Erbium Doped Fiber
Amplifier Based Optical Communication - A
Review
N SINDHU and P. K. SHAFEENA
Abstract - The gain flattening of Erbium-doped fiber
amplifiers (EDFA) has been a research issue in recent years,
with the development of high capacity wavelength division
multiplexing (WDM) optical communication systems. For single
channel systems, the gain variation is not a problem. However,
as the number of channels increases, the transmission problem
arises because a conventional EDFA has intrinsic non-uniform
gain. They typically present gain peaking at about 1530 nm and
the useful gain bandwidth may be reduced to less than 10 nm.
The gain of EDFAs depends on a large number of device
parameters such as erbium-ion concentration, amplifier length,
core radius and pump power. To increase the gain-bandwidth
of an amplified lightwave system several methods can be used,
but equalising optical filters operating as spectrally selective
loss elements appear to be the best candidates. This paper
mainly focuses on different methods used for gain flattening in
EDFA.
Index Terms—Optical amplifiers, EDFA, Optical filter,
I. INTRODUCTION
The increasing demand for new telecommunications services
is creating an increase in network capacity requirements.
System capacity can be increased by1) deploying new
optical fiber, 2) increasing transmission bit rate, 3)
multiplexing more channels on to the existing fiber.
Deployment of new fiber is time and cost-prohibitive
because it involves equipment burial/installation, while
increasing transmission bit rate is problematic due to the cost
of replacing transmission equipment. Wavelength division
multiplexed (WDM) technology employing erbium-doped
fiber amplifiers (EDFA’s), however, provides an immediate
cost effective alternative for increasing network capacity. In
a multichannel environment optical amplifiers should
provide a flat gain spectrum, independent of input
parameters; however, this is not the case with erbium-doped
fiber amplifiers. Indeed, the EDFA exhibits a non-uniform
and dynamic gain spectrum, so that each channel input (at
different wavelengths) to the amplifier experiences a
different gain [1].
N SINDHU and P. K. SHAFEENA are with Dept. of ECE, Government
Engineering College Wayanad, Kerala. Emails: sindhun@gecwyd.ac.in,
Shafeenapk@gmail.com
When EDFA’s are cascaded, this wavelength-dependent
gain spectrum produces an accumulated imbalance (between
different channels) in both the received power and signal-to-
noise ratio (SNR) as signals propagate along the amplifier
chain. The accumulated power and SNR imbalance can limit
system performance in three different ways. First, the
received power imbalance can eventually exceed that
allowed by receiver dynamic range. Second, accumulated
SNR imbalance can result in the bit error rate (BER), at
certain wavelengths, falling below required levels. Third, the
minimum received signal power can fall below what is
required by receiver sensitivity (for a given bit rate), due to
inadequate gain compensation.
The fiber optic communication also have a number of
applications in the area of telecommunication. In this paper
we are focusing on optical amplifiers which are essential part
in fiber optic communications. The optical amplifier of our
interest in this paper will be erbium doped fiber amplifier
(EDFA) which is widely preferred in the area of fiber optic
communication. In this paper an analysis of the performance
of optical system consisting of single or a chain of EDFAs
(depending upon the system performance) for different data
formats are made.
The gain spectrum of EDFA has asymmetrical twin
peaks, due to a luminescent spectrum caused by fine
structure of the energy levels. The gain spectrum isn't flat, so
there is power deviation between amplified signals. In the
long haul optical transmission systems, optical signals are
transmitted by a multi-amplifier system, so differences
between optical signal powers are accumulated. When
dividing optical signals for various wavelengths at the
receiver, other optical signals affect the signal as noise. If
there are differences between optical signals transmitted by
amplifiers, optical signals with low signal to noise ratio are
more and more deteriorated at WDM as that are transmitted
by EDFA. So as the transmission distance becomes more
then the number of signal channels decrease. Therefore, it is
needed that the gain of EDFA be flat in the range of signals
for getting an adequate signal to noise ratio at each
wavelength. One of the methods to flatten gain of EDFA is
using an optical gain-flattening filter. This is the method to
flatten the gain of EDFA by using a filter with reverse loss
spectrum against the gain spectrum. This filter is called the
optical gain-flattening filter. Section II gives an introduction
to optical fiber amplifiers and explains the need for optical
amplifiers in fiber optic communication and also this section
gives a small introduction to the different classification of
optical amplifiers and their typical applications. Section III
2. N SINDHU and P. K. SHAFEENA 51
International Journal of Emerging Trends in Electrical and Electronics (IJETEE) Vol. 1, Issue. 2, March-2013.
explains about EDFA in detail. The principle of operation,
working architecture, advantages, applications and problems
faced by the use of EDFA will be explained. Section IV
focus on the gain flattening and different methods for flatten
the gain spectrum. The paper will be concluded in section V.
II. OPTICAL AMPLIFIERS
The transmission of signal in optical fiber is affected by
two fundamental limitations i.e. attenuation and dispersion.
Here dispersion is as a result of signal components at
different wavelength travelling at different speeds inside the
optical fiber. Attenuation is as a result of the partial
transparency of the glass materials constituting the optical
fiber which will result in gradual reduction of amplitude of
the signal propagated and hence the gain. Both attenuation
and dispersion results in the reduction of precision associated
with the signal transmission through optical fiber. In the case
of single mode fibers the effect of dispersion is neglected but
the problem associated with attenuation is a very serious
issue. Transmission of signal in optical fibers mostly takes
place around 1310nm and 1550 nm. The typical attenuation
of silica fiber is in the order of 0.2dB/km at 1550nm. Hence
after a distance of approximately 100km, the signal
attenuation will be nearly 20dB which will result in
considerable loss of signal.
The optical amplifiers play a key role in limiting the
attenuation of optical communication network. Optical
amplifiers compensate for propagation losses in long
distance links and branching losses in access networks, at
the same time avoiding costly two-way conversions between
optical and electrical signals. By optical amplification the
network performance is increased and also optical
amplification results in lowering the number of repeaters and
thereby simplifying the network. Optical amplifiers amplify
the signals and thereby increases the SNR of the signals and
also it brings the BER rate below 10-9
which is the desired
rate in optical communication.
A. WORKING PRINCIPLE
The main working principle of Optical amplifiers are
explained below. To achieve optical amplification the
population of the upper energy level has to be greater than
that of lower energy level (N2 ›N1 where N2 , N1 are the
population densities of upper and lower state respectively ),
this condition is known as population inversion and is
achieved by exciting electron into higher energy level by
external source called pumping. Here one photon enters in
the amplifier, An atom is stimulated in order to decay to the
fundamental state, emitting a photon identical to the one
which gave rise to it; This process is repeated and the signal
gets amplified (gain). Stimulated emission occur when an
incident photon with energy E= hc/λ interact with electron in
the upper energy state causing it return to lower state with
creation of second photon, where h is plancks constant, c is
the velocity of light and λ is the wavelength of light.
B. CLASSIFICATION OF OPTICAL AMPLIFIERS
Optical amplifiers are basically classified into three based
on their typical application in optical communication, they
are as follows:
a. Semiconductor Optical amplifiers(SOA)
SOAs uses the principle of stimulated emission to amplify
the optical signals. Output-level control that accepts a wide
range of input power and delivers constant output power is
essential for in-line optical amplifiers, optical burst and
packet systems and in all optical regeneration and reshaping
(2R). Semiconductor optical amplifiers SOA's can meet this
demand. The reason for this is because SOA has short
carrier lifetime of about several tenths to several hundreds of
picoseconds compared to several hundred microseconds to
several milliseconds in other optical amplifiers. Hence SOAs
are generally used as pre amplifiers which is located before
the receiver.
b. Rare earth doped optical amplifiers
Erbium doped fiber amplifiers (EDFA), Thulium doped
fiber amplifiers etc comes under this classification. These
types of optical amplifiers are widely used as power
amplifiers which are located at the transmitter in optical
communication systems. It targets the compensation of the
loss of the modulation devices and the lack of power in
lasers. The detailed working of these types of amplifiers will
be explained in the following sections.
c. Raman optical amplifiers
d.
Raman scattering occurs in any silica glass which means
if we inject an optical beam (pump) in an optical fiber , then
a signal passing through that fiber will be amplified if its
frequency is around the shifted frequency of the pump. This
is called Stock shift, which is a round 13 GHz (equivalent to
about 100 nm) from the pump propagating beam frequency
assuming that its wavelength is 1450 nm. That means the
signal will be amplified if its wavelength is 1550 nm. Raman
amplifiers are based on this phenomenon. The exciting
property of RAs is reduction for chromatic dispersion and
loss . This can be done by increasing the pump power. But if
the number of cascaded amplifiers increases, then gain
fluctuation might occur. One way to deal with this situation
is to optimize the multi span amplifiers jointly rather than
individually. Raman amplifiers are used as line amplifiers in
optical applications which should provide high gain, high
output power and low noise. The effect of Raman amplifiers
is similar to the cascade of a pre amplifier and a power
amplifier.
III. ERBIUM DOPED FIBER AMPLIFIER (EDFA)
A) Physical Principle of EDF Amplification
At the heart of EDFA technology is the Erbium Doped
Fiber (EDF), which is a conventional Silica fiber doped with
Erbium. When the Erbium is illuminated with light energy at
a suitable wavelength (either 980nm or1480nm) it is excited
to a long lifetime intermediate state (see Figure 1), following
which it decays back to the ground state by emitting light
within the 1525-1565 nm band. If light energy already exist
within the 1525-1565nm band, for example due to a signal
channel passing through the EDF, then this stimulates the
decay process (so called stimulated emission), resulting in
additional light energy. Thus, if a pump wavelength and a
signal wavelength are simultaneously propagating through
an EDF, energy transfer will occur via the Erbium from the
3. N SINDHU and P. K. SHAFEENA 52
International Journal of Emerging Trends in Electrical and Electronics (IJETEE) Vol. 1, Issue. 2, March-2013.
pump wavelength to the signal wavelength, resulting in
signal amplification.
Figure 1: The energy levels of the Erbium with the EDF.
The Erbium can be either pumped by 980nm light, in
which case it pass through an unstable short lifetime state
before rapidly decaying to a quasi-stable state, or by 1480nm
light in which case it is directly excited to the quasi-stable
state. Once in the quasi-stable state, it decays to the ground
state by emitting light in the 1525-1565nm band. This decay
process can be stimulated by pre-existing light, thus resulting
in amplification.
B) Basic EDFA Design
In its most basic form the EDFA consist of a length of
EDF (typically 10-30m), a pump laser, and a component
(often referred to as a WDM) for combining the signal and
pump wavelength so that they can propagate simultaneously
through the EDF. In principle EDFA’s can be designed such
that pump energy propagates in the same direction as the
signal (forward pumping), the opposite direction to the
signal(backward pumping), or both direction together. The
pump energy may either by 980nm pump energy,1480nm
pump energy, or a combination of both. Practically, the most
common EDFA configuration is the forward pumping
configuration using 980nm pump energy, as shown in Figure
2. This configuration makes the most efficient use of cost
effective, reliable and low power consumption 980nm
semiconductor pump laser diodes, thus providing the best
overall design with respect to performance and cost trade-
offs. Besides the three basic components described above,
Figure 2 also shows additional optical and electronic
components used in a basic single stage EDFA. The signal
enters the amplifier through the input port, and then passes
through a tap which is used to divert a small percentage of
the signal power (typically 1-2%) to an input detector.
Figure 2: Diagram of a typical single stage EDFA, showing
the three basic components (EDF, pump and WDM
combiner), as well as additional optical and electronic
components used to optimize performance and control the
amplifier.
The signal then passes through an isolator, before being
combined with pump energy emitted by the 980nm pump
laser diode. The combined signal and pump energy
propagate along the EDF, where signal amplification occurs,
and then the amplified signal exits the EDF and passes
through a second isolator. The purpose of the two isolators,
which allow light to pass only in a single direction, is to
ensure that lasing cannot take place within the EDF.
Furthermore, the output isolator also acts as a filter for
980nm light propagating in the forward direction, thus
stopping the 980nm light from exiting the amplifier output
port. In a multi-channel WDM amplifier, a Gain Flattening
Filter (GFF) is usually placed following the output isolator in
order to flatten the gain spectrum, as shown in Figure 3. The
attenuation spectrum of the GFF is designed to match the
Gain spectrum of the EDF (operating at a given fixed gain),
such that the combination of the two produces a flat gain.
Following the GFF the signal passes through an output tap
used to divert a small percentage of the output power
(typically 1-2%) to the output detector. The output and input
detectors are used to monitor the input and output power
respectively, and thus provide feed-back to the control unit,
which controls the amplifier by setting the pump laser
current, and thus the amount of pump power injected into the
EDF.
Figure 3: Use of a Gain Flattened Filter (GFF) to achieve a
flat gain spectrum. The attenuation spectrum of the filter
matches the gain spectrum at the output of the EDF, such
that the combination of the two provides a flat gain
spectrum.
IV. GAIN FLATTENING IN EDFA
Erbium doped fiber amplifiers have had a major impact
in the field of light wave communications. Optical amplifiers
have contributed to the growth of a fifth generation of optical
communication systems. But as the demands on the networks
increased techniques like Dense Wavelength Division
Multiplexing (DWDM) were developed. The performance of
DWDM in ultra-long haul networks improved because of the
fact that amplifiers were available that could amplify the
wavelengths used in the network without requiring any
conversion of the optical signal to the electrical signal. The
importance of EDFA’s is due to their compatibility with the
4. N SINDHU and P. K. SHAFEENA 53
International Journal of Emerging Trends in Electrical and Electronics (IJETEE) Vol. 1, Issue. 2, March-2013.
fiber network, low insertion loss, polarization insensitivity,
high gain levels and near quantum limited noise
performance. In DWDM transmission systems and their
related optical networks, one of the key technological issues
is the achievement of broad and flat gain bandwidth for
Erbium Doped Fiber Amplifiers (EDFA’s). Gain differences
occur between optical channels having large wavelength
spacing (e.g. Δλ> 1nm). In long amplifier chains, even small
spectral gain variations (e.g. ΔG < 0.75 dB) can result in
large differences in the received signal power, causing
unacceptably large BER discrepancies between received
signals. For some optical channels, complete power
extinction can occur at the system output, due to insufficient
gain compensation along the amplifier chain. Additionally,
the ASE generated in the region of highest gain (i.e., near λ =
1530 nm) in un equalized EDFAs causes homogenous gain
saturation, which affects WDM channels at longer
wavelengths.
Uniformity of gain involves two aspects, namely gain
equalization and gain flattening. Gain equalization means
achieving identical gains for a discrete number (two or three)
of optical channels. Gain flattening means achieving a
spectrally uniform gain bandwidth. Gain equalization can be
achieved with requiring gain flattening. For example, given
an EDFA of length L, the pump power can be chosen such
that the gains at two different wavelengths become exactly
equal due to signal re-absorption at short wavelengths. This
method though useful does not work under saturated
operating conditions. Later methods to flatten the gain using
hosts such as fluoro zirconate glass were investigated. It was
found that the gain spectrum for these fibers though more
uniform did not provide high pump efficiency. Therefore,
these methods were not investigated any further.
Standard EDFA gain flattening techniques were based on six
different principles: (1) Gain clamping with enhanced
inhomogeneous saturation, (2) Use of passive
internal/external filters, (3) Use of external active filters, (4)
Cascading EDFAs with different gain spectra, (5) spatial
hole burning in twin core fibers and (6) Adjustment of input
signal powers [1] . Among these techniques, the only
dynamic technique was the one using AOTF’s as
transmission filters. With the increase in network traffic, the
number of WDM channels increased and so the demands on
the amplifiers used in the network also increased. EDFAs
were now required to provide a flat gain over a broad range
of wavelengths and also cater to changes in the optical power
levels due to add and drop of channels along the link. This
called for dynamic gain flattening techniques like the one
using AOTF’s but this method had its own drawbacks like a
high insertion loss and the requirement of a high RF power
for the acoustic wave.
This section describes about the different methods used to
flatten the gain spectrum of EDFA.
A. OPTICAL GAIN FLATTENING FILTERS
In general, the gain profile of an EDFA can be flattened
by modifying the material composition in the erbium-doped
fiber (EDF) [2], or by using optical filters to compensate for
the variations in the gain spectrum [3]–[8]. Various kinds of
optical filters have been demonstrated for this application,
including long-period fiber gratings [3], [4], fiber Bragg
gratings [5], fiber acousto optic tunable filters [6], [7],
Mach–Zehnder filters [8], and a split-beam Fourier filter [9].
As the method of flattening a gain spectrum of EDFA,
methods using optical gain-flattening filter with reverse loss
spectrum against gain spectrum are common. The principles
of optical gain-flattening filter are shown in Figure . It is
shown that EDFA has gain dependence on wavelength
before flattening. After flattening of gain by using the optical
gain-flattening filter, it is shown that dependence of EDFA
on wavelength is flattened and deviation of signal power is
improved. In Figure 2 sample configuration of EDFA with
optical gain-flattening filter is shown. Normally optical gain-
flattening filter is used in series with EDFA as shown in
Figure:4, where the filter is inserted in the middle stage of
EDFA between two erbium doped fibers (EDFs).
Figure :4 – gain flattening filter.
Commonly used Optical filters for gain flattening are
etalon filter a dielectric filter and a long period fiber Bragg
grating filter a Mach-Zehnder type filter and the split-beam
Fourier filter. The above-mentioned intrinsic EDFA gain-
wavelength characteristics have asymmetrical twin peaks
and the loss-wavelength characteristics of the optical gain-
flattening filter to compensate the EDFA gain wavelength
characteristics have counterbalanced characteristics.
The EDFA gain-wavelength characteristics depend on
power characteristics of pumping lasers, the concentration of
erbium ion in EDF, the kind of co-doped ion and its volume,
and the length of EDF as well.
The gain-flattening filter requires flexibility of design for
various kinds of EDFA gain-wavelength characteristics to
minimize errors between the target and design. Moreover it
is required to have low polarization dependence loss (PDL)
and capability of producing highly reproducible spectral
profiles.
B. GAIN FLATTENING BY USING DUAL CORE FIBER
Many of the techniques involve the use of expensive
components and complicated design. The use of twin-core
fiber is also an obvious choice in which both cores are
identically doped with erbium. This technique has been
suggested in 1993 by Laming et al[10]. and it involves the
concatenation of a length of single core EDF with a length of
twin-core EDF. The purpose of the twin-core EDF here is to
introduce spatial hole burning which decreases the excessive
gain at certain wavelength. Wu and Chu has also suggested
the use of twin-core EDF for gain flattening by launching
pump power into both cores. The ratio of these powers has to
5. N SINDHU and P. K. SHAFEENA 54
International Journal of Emerging Trends in Electrical and Electronics (IJETEE) Vol. 1, Issue. 2, March-2013.
be predetermined. This technique is not practical as it is
difficult to have simultaneous access of the two input cores.
The EDFA with flat gain over a wide wavelength range can
simply be constructed by means of a length of dual-core
fiber[11]. This fiber consists of two closely-spaced cores,
one of which is doped with erbium and the other is
nondoped. This amplifier has a gain variation less than 0.7
dB over the wavelength range 1525 to 1555 nm.
Furthermore, the amplifier noise floor is very low,
approaching 4 dB.
Figure :5 -Structure of dual core gain-flattened EDFA.
The structure of the amplifier is shown in Fig. . It
consists of three components: 1) the input fiber coupler
which combines the 1550 nm signal and the 980 nm pump
power into one of the cores of the fiber; 2) the dual core
fiber; and 3) the output fiber coupler which separates the
amplified 1550 nm signal from the residual pump power. It
is noted that only the erbium-doped core is used for
connection to the two couplers. The other core (undoped
core) is not used. In our experiment, an optical spectrum
analyzer is connected to the output port of the second
coupler for wavelength characterization of the amplifier. The
input signal is continues wave at different wavelengths.
The principle of operation of this amplifier is that the
coupling efficiency from core 1 to core 2 is maximum at the
wavelength where the gain is maximum, i.e., at 1533 nm. In
this case, the excessive signal is coupled to core 2 which is
not used. On the other hand, the coupling efficiency from
core 2 to core 1 at this wavelength is minimum, so that this
excessive signal that has been coupled to core 2 would not
return to core 1.
The reason for the nonreciprocity of the coupling
efficiency is because one core is doped with erbium while
the other core is nondoped. The doped core is an amplifying
medium whereas the nondoped core is a passive medium
C. GAIN FLATTENING BY USING COMPOSITE
AMPLIFIERS
Zervas et. al[12] proposed in their paper, a composite
amplifier design where a commercially available fiber
isolator is incorporated into the erbium doped segment of the
EDFA. The active length now comprises of two erbium
doped fiber lengths with the isolator spliced in between. The
amplifier is pumped in the forward direction i.e. the pump
and signal co-propagate. It was found that without the
isolator, the backward ASE grows to a high value towards
the input end of the amplifier, becomes comparable with the
pump power and, therefore, significantly depletes the
population inversion of the gain medium. In fact, at the input
end of the EDFA, the pump power is primarily used to
amplify the backward traveling ASE, which considerably
exceeds the signal. This causes an increase in the noise
figure and also introduces non-uniformity in the gain
spectrum. If the isolator was used, then the isolator cuts
down the backward travelling ASE. This causes a reduction
in the pump depletion at the input due to the ASE and
therefore an increased gain and improved noise figure. Also,
the uniformity in the gain is increased as the ASE effect is
reduced.
Figure :6 -A new design of a gain-flattened amplifier using
an unpumped erbium doped fiber as a gain-flattening
filter
It is well known that an erbium-doped fiber has a strong
absorption in the wavelength range 1500 – 1600 nm, which
is wavelength dependent. In this design we use this very fact
to our advantage.
In this composite amplifier, the conventional amplifier is
divided into three stages. The first stage consists of a
standard forward pumped EDFA configuration. At the output
of this amplifier, a WDM coupler removes the residual pump
power and the signal is input to a length of unpumped
erbium-doped fiber. This is now input to another
conventional amplifier where it is amplified by the
remaining pump power. The issues in this design are (1)
Length of the fiber used in the unpumped section and (2) The
length of the EDF fibers used in the two conventional
amplifier sections. The other factors that can be investigated
are the improvement in the dynamic range provided by this
composite amplifier in terms of the input signal power and
the pump power variations.
V. CONCLUSION
This paper investigates different methods for gain
flattening in erbium doped amplifier. The gain of EDFAs
depends on a large number of device parameters such as
erbium-ion concentration, amplifier length, core radius and
pump power. So by changing any one of these parameters we
can make a flat gain spectrum.
REFERENCES
[1] E. Desurvire, Erbium Doped Fiber Amplifiers Principles and
Applications, John-Wiley & Sons, Inc, New York, 1994.
[2] M. Yamada, T. Kanamori, Y. Terunuma, K. Oikawa, M.
Shimizu, S.Sudo, and K. Sagawa, “Fluoride-based erbium-
doped fiber amplifier with inherently flat gain spectrum,” IEEE
Photon. Technol. Lett., vol. 8, pp. 882–884, June 1996.
6. N SINDHU and P. K. SHAFEENA 55
International Journal of Emerging Trends in Electrical and Electronics (IJETEE) Vol. 1, Issue. 2, March-2013.
[3] M. K. Pandit, K. S. Chiang, Z. H. Chen, and S. P. Li, “Tunable
longperiod fiber gratings for EDFA gain and ASE
equalization,” MicrowaveOpt. Technol. Lett., vol. 25, pp. 181–
184, Mar. 1999.
[4] P. F. Wysocki, J. B. Judkins, R. P. Espindola, M. Andrejco, and
A. M. Vengsarkar, “Broad-band erbium-doped fiber amplifier
flattened beyond 40 nm using long-period grating filter,” IEEE
Photon. Technol. Lett., vol. 9, pp. 1343–1345, Oct. 1997.
[5] S. K. Liaw, K. P. Ho, and S. Chi, “Dynamic power-equalized
EDFA module based on strain tunable fiber Bragg gratings,”
IEEE Photon.Technol. Lett., vol. 11, pp. 797–799, July 1999.
[6] R. Feced, C. Alegria, M. N. Zervas, and R. I. Laming,
“Acoustooptic attenuation filters based on tapered optical
fibers,” IEEE J. Select. Top.Quantum Electron., vol. 5, no. 3,
pp. 1278–1288, 1999.
[7] S. K. Yun, B. W. Lee, H. K. Kim, and B. Y. Kim, “Dynamic
erbium- doped fiber amplifier based on active gain flattening
with fiberacoustooptic tunable filter,” IEEE Photon. Technol.
Lett., vol. 11, pp. 1229–1231, Oct. 1999.
[8] J. Nilsson, W. H. Loh, S. T. Hwang, J. P. de Sandro, and S. J.
Kim, “Simple gain-flattened erbium-doped fiber amplifier with
a wide dynamic range,” in Opt. Fiber Commun. Conf.
Washington, DC: Optical Society of America, 1997, OSA Tech.
Dig., p. 163.
SINDHU received BTech from NSS
College of Engg.,Palakkad in 1996
,MTech with honours from National
Institute of Technology Karnataka in 2004,
and currently working towards PhD at
Kerala University. After graduation she
joined LBS College of Engineering as
Lecturer. In 2004 she joined Govt.
Engineering College Sreekrishnapuram,
Palakkad. She was Assistant Professor
from 2006 and joined at Govt.Engineering
College Wayanad since 2010. She is ,Incharge of the Innovation
centre under Centre for Engineering Research &Development
Satellite Centre at GECW ,holds the charge as Placement Officer,
she is Life member of ISTE. She is the principal Investigator of two
projects sponsored by Centre for Research &Development
,Thiruvananthapuram,Kerala She has authored and coauthored
several papers in National Conferences and International Journals.
Her Research interests include Optical Amplifiers especially, Gain
Flattening, Controlling Power transients ,Compensating spectral loss
variations etc. in EDFA’s.
P. K. SHAFEENA (shafeenapk@.com)
received her B.Tech degree in electronics
and communication engineering in from
Govt. Engineering College Wayanad
2011 from Govt. Engineering College
Wayanad. She is now a post graduate
student in Govt. Engineering College
Wayanad. She has authored a paper which
has been accepted for national conference
(CISP-2013).