The document outlines a two-day training course on Controller Area Network (CAN) technology, priced at $1899. It covers the ISO 11898 standard, CAN protocol applications in automotive and embedded systems, and various technical aspects including bus communication and network topology. The training is aimed at engineers, technicians, and project managers involved in automotive embedded systems.

1. ISO EPA CAN protocol
CONTROLLER AREA
NETWORK (CAN) TRAINING
CAN BUS Embedded Systems CSMA
Price: $1899.00 Length: 2 Days

2. Controller Area Network (CAN) Training
https://www.tonex.com/training-courses/controller-area-network-can-training/
Controller Area Network (CAN) training covers the ISO 11898
standard of decision for car producers and Vehicle Applications.
Affirmed for use as an ISO and EPA analytic network, its use keeps on
developing. Controller Area Network (CAN) training covers the
hypothesis, task and utilization of the CAN convention, and its
applications in the car and different enterprises.
CAN is the most generally utilized car transport design. The
Controller Area Network (CAN) transport is the command the car
business and the CAN controllers are sold as on-chip peripherals in
microcontrollers. Controller Area Network (CAN) physical layer is
made out of a contorted combine multidrop link as indicated with a
length going from 1,000m at 40Kbps to 40m at 1Mbp.

3. Controller Area Network (CAN) Training
https://www.tonex.com/training-courses/controller-area-network-can-training/
Who Should Attend
• Design engineers
• Verification and valuation engineers
• Test engineers
• Programmers
• Technicians
• Embedded hardware and software engineers
• Automotive embedded systems technicians and field engineers
• Project managers

4. Controller Area Network (CAN) Training
https://www.tonex.com/training-courses/controller-area-network-can-training/
Learn about:
• Principles of Controller Area Network (CAN)
• Technical introduction to serial bus systems
• Controller Area Network (CAN) implementation in Embedded Systems
• CAN protocol and other standards such as J2284, J2411, and J1939
• CAN physical and data link layers in some details
• J1939/71 Recommended Practice for Vehicle Application Layer
• CAN application layers standards, regulations, and implementation requirements
• The SAE standards, J1939 Automotive Engineering Recommended Practice for a Serial Control and
Communications Vehicle Network
• CAN architecture and protocols
• CAN controller programming
• CAN physical and data link layers
• CAN (Controller Area Network) characteristics of the physical layer (High-/Low-Speed-CAN)
• Bus access methods, framing, bit timing, bit stuffing
• Automotive Networks and CAN Bus topology
• Principals of CSMA/CD and CSMA/CA
• CAN Differential Signaling
• CAN applications examples
• Distributed and embedded systems in the Automotive domains
• CAN Bus Use in Automotive and Agriculture
• Controller Area Network (CAN) Bus J1939 Data Acquisition Methods

5. Controller Area Network (CAN) Training
https://www.tonex.com/training-courses/controller-area-network-can-training/
Course Agenda:
Overview of Automotive Buses
• The requirements of a bus in an automotive environment
• Electronification of motor vehicles
• Primary tasks in bus networking
• Standards and implementation
• Introduction to CAN
• General network topology
• Overview of J2411, J2284, IDB, J1939, Diagnostics on CAN
• J1939 in-depth review

6. Controller Area Network (CAN) Training
https://www.tonex.com/training-courses/controller-area-network-can-training/
CAN Architecture
• The Controller Area Network (CAN) bus
• Node architecture, bus-connection and termination
• Voltage levels & corresponding bit values
• Physical layer
• Data ink layer
• Controller Area Network (CAN) physical layer
• Twisted pair multidrop cable
• CAN bus length and range
• Payload of a message
• Cyclic redundancy code (CRC)
• Application or higher-level protocols
• Nodes on the network
• J1939 protocol is common
• Nondestructive Bus Arbitration
• CAN bus arbitration
• Nondestructive bus arbitration,
• The arbitration field
• Fault Tolerance
• Noise Tolerance
• Stateless Messaging
• CANOpen Considerations

7. Controller Area Network (CAN) Training
https://www.tonex.com/training-courses/controller-area-network-can-training/
Layered ISO Standard Architecture
• Standard CAN Identifier
• Extended CAN Identifier
• Details of a CAN Bus
• CAN Bus Traffic
• CAN Test Bus
• Common-Mode Noise Coupled Bus Lines
• Split Termination

8. Controller Area Network (CAN) Training
https://www.tonex.com/training-courses/controller-area-network-can-training/
Basic Bus Communication Requirements
• Physical Layer Requirements
• Bus Length vs Signaling Rate
• Cables
• Shield Termination
• Grounding
• Line Terminations
• Connectors
• Filters/Chokes
• Stub Length and Loop Delays
• Galvanic Isolation and Total Propagation Delay
• Physical Layer Variables (bit timing requirements)
• Node Differential Capacitance and Spacing
• Maximum Number of Nodes

9. Controller Area Network (CAN) Training
https://www.tonex.com/training-courses/controller-area-network-can-training/
Characteristics of the CAN Protocol
• Addressing, message transmission & reception
• Message formats and structure
• Larger Data Field and the consequences
• Bit rate switching
• Bus access method and arbitration
• Message types, detailed description of the structure and
functions
• Increase noise immunity, neutralize errors
• Error detection mechanisms
• Error treatment & tracking
• Motivation for the bit time interval
• Relation of baud rate and length of the CAN bus
• Synchronization and resynchronization

10. Controller Area Network (CAN) Training
https://www.tonex.com/training-courses/controller-area-network-can-training/
CAN Lower-layer standards
• Data-Flow Model
• CAN-based higher-layer protocols
• Standardized approaches
• Other approaches
• CANopen Lift
• Security
• Development tools
• External links

11. CONTROLLER AREA
NETWORK (CAN) TRAINING
Price: $1899.00 Length: 2 Days
VISIT TONEX.COM
VISIT TONEX.COM

12. https://www.tonex.com/