Polymer is a macro molecule formed by the union of many small molecules called monomers. Polymers can be linear or branched depending on their structure. They may be homopolymers made of the same monomer, or copolymers made of different monomers. Polymerization is the process of linking monomers together to form large polymer molecules. There are three main types of polymerization: addition polymerization, condensation polymerization, and copolymerization. Addition polymerization yields an exact multiple of monomeric units through intermolecular rearrangement of double bonds using heat, light or catalysts. Condensation polymerization occurs through elimination reactions between polar group-containing monomers to form polymers and byproducts like
The document discusses ring opening polymerization (ROP), which is a chain growth polymerization where cyclic monomers react to form polymer chains by opening their ring structures. There are three main types of ROP - radical, anionic, and cationic - depending on whether the reactive center is a radical, anion, or cation. Examples are given of monomers that can undergo each type of ROP, along with diagrams of the mechanisms. Common applications of ROP include nylon and biopolymers like polysaccharides.
Polymers are large molecules composed of many repeating structural units. The three main types of polymerization are addition, condensation, and insertion. Addition polymerization involves chain growth where a monomer adds to the end of the growing polymer chain. Condensation polymerization involves step growth where two monomers combine by removing a small molecule. Free radical polymerization is a common type of addition polymerization that uses an initiator to generate free radicals to start the chain reaction.
- Polymers are giant molecules formed by linking together small repeating units called monomers via covalent bonds. There are three main types of polymerization: addition, condensation, and copolymerization.
- Properties of polymers depend on factors like the monomer type, the degree of polymerization, tacticity, and whether the polymer is crystalline or amorphous. Common polymers include polyethylene, polypropylene, nylon, polyethylene terephthalate.
- Natural rubbers are polymers of the monomer isoprene that provide flexibility and elasticity. However, natural rubber has limitations that are overcome through vulcanization, which introduces cross-links between polymer chains through the addition of sulfur.
This document provides an introduction to polymers including their classification, structure, common types, and mechanisms of polymerization. Polymers are macromolecules composed of repeating structural units connected through polymerization reactions. They can be classified based on their structure as linear, branched, or cross-linked. Common addition polymers include polyethylene, polypropylene, polyvinyl chloride, and nylon. Condensation polymers include polyethylene terephthalate and polyamides. Polymerization occurs primarily through either addition or condensation reactions. Free radical addition polymerization follows initiation, propagation, and termination steps.
Copolymerization involves polymerizing two or more different monomers simultaneously so that the resulting polymer contains more than one type of repeating unit in the polymer chain. There are several types of copolymers including random, alternating, block, and graft copolymers. The composition of a copolymer depends on factors like the monomer concentrations and their reactivity ratios. Kinetic models can be used to predict the monomer composition of the copolymer based on the monomer feed using methods like the Mayo-Lewis equation or the Fineman-Ross equation. The reactivity ratios influence whether an ideal random copolymer, alternating copolymer, or block copolymer will form. Ionic copolymerization
This document provides an introduction to conducting polymers. It discusses how conducting polymers were discovered in the late 1970s and can be used as alternatives to metal conductors due to advantages like being light weight, flexible, and having non-metallic surface properties. Common conducting polymers include polyacetylene, polypyrrole, and polyaniline. The document outlines how conducting polymers are classified and the doping process used to increase their conductivity. Potential applications of conducting polymers discussed include coatings, sensors, biocompatible polymers, batteries, displays, and conductive adhesives.
This document discusses the conducting polymer polyaniline. It provides an outline that covers an introduction to polymers, types of polymers, conducting polymers such as polyaniline, synthesis of polyaniline, properties of polyaniline nanowires, and applications. Polyaniline nanowires are a type of one-dimensional conducting polymer nanowire that can be used as an active layer in chemical sensors. They can be synthesized via chemical or electrochemical polymerization of aniline monomers. Potential applications of polyaniline nanowires and conducting polymers include uses in transistors, LEDs, solar cells, displays, and electromagnetic shielding.
The document discusses ring opening polymerization (ROP), which is a chain growth polymerization where cyclic monomers react to form polymer chains by opening their ring structures. There are three main types of ROP - radical, anionic, and cationic - depending on whether the reactive center is a radical, anion, or cation. Examples are given of monomers that can undergo each type of ROP, along with diagrams of the mechanisms. Common applications of ROP include nylon and biopolymers like polysaccharides.
Polymers are large molecules composed of many repeating structural units. The three main types of polymerization are addition, condensation, and insertion. Addition polymerization involves chain growth where a monomer adds to the end of the growing polymer chain. Condensation polymerization involves step growth where two monomers combine by removing a small molecule. Free radical polymerization is a common type of addition polymerization that uses an initiator to generate free radicals to start the chain reaction.
- Polymers are giant molecules formed by linking together small repeating units called monomers via covalent bonds. There are three main types of polymerization: addition, condensation, and copolymerization.
- Properties of polymers depend on factors like the monomer type, the degree of polymerization, tacticity, and whether the polymer is crystalline or amorphous. Common polymers include polyethylene, polypropylene, nylon, polyethylene terephthalate.
- Natural rubbers are polymers of the monomer isoprene that provide flexibility and elasticity. However, natural rubber has limitations that are overcome through vulcanization, which introduces cross-links between polymer chains through the addition of sulfur.
This document provides an introduction to polymers including their classification, structure, common types, and mechanisms of polymerization. Polymers are macromolecules composed of repeating structural units connected through polymerization reactions. They can be classified based on their structure as linear, branched, or cross-linked. Common addition polymers include polyethylene, polypropylene, polyvinyl chloride, and nylon. Condensation polymers include polyethylene terephthalate and polyamides. Polymerization occurs primarily through either addition or condensation reactions. Free radical addition polymerization follows initiation, propagation, and termination steps.
Copolymerization involves polymerizing two or more different monomers simultaneously so that the resulting polymer contains more than one type of repeating unit in the polymer chain. There are several types of copolymers including random, alternating, block, and graft copolymers. The composition of a copolymer depends on factors like the monomer concentrations and their reactivity ratios. Kinetic models can be used to predict the monomer composition of the copolymer based on the monomer feed using methods like the Mayo-Lewis equation or the Fineman-Ross equation. The reactivity ratios influence whether an ideal random copolymer, alternating copolymer, or block copolymer will form. Ionic copolymerization
This document provides an introduction to conducting polymers. It discusses how conducting polymers were discovered in the late 1970s and can be used as alternatives to metal conductors due to advantages like being light weight, flexible, and having non-metallic surface properties. Common conducting polymers include polyacetylene, polypyrrole, and polyaniline. The document outlines how conducting polymers are classified and the doping process used to increase their conductivity. Potential applications of conducting polymers discussed include coatings, sensors, biocompatible polymers, batteries, displays, and conductive adhesives.
This document discusses the conducting polymer polyaniline. It provides an outline that covers an introduction to polymers, types of polymers, conducting polymers such as polyaniline, synthesis of polyaniline, properties of polyaniline nanowires, and applications. Polyaniline nanowires are a type of one-dimensional conducting polymer nanowire that can be used as an active layer in chemical sensors. They can be synthesized via chemical or electrochemical polymerization of aniline monomers. Potential applications of polyaniline nanowires and conducting polymers include uses in transistors, LEDs, solar cells, displays, and electromagnetic shielding.
1) Polymers are large molecules formed from the combination of small molecules called monomers through a process called polymerization.
2) Polymerization is initiated by a reactive site on a monomer that is produced using an initiator. This allows monomers to add onto a growing polymer chain.
3) Polymers are classified based on their source, thermal properties, polymerization mechanism, and structure. Some examples of polymerization mechanisms discussed are chain-growth, step-growth, free radical, anionic, and cationic polymerization.
This document discusses polymers, including their classification, types of polymerization, characteristics, and applications. Polymers can be classified based on their source as natural, semi-synthetic, or synthetic. They can also be classified by their structure as linear, branched, or cross-linked. The two main types of polymerization are addition and condensation. Polymers have a variety of characteristics like low density and good corrosion resistance. They have wide applications in medicine, consumer products, industry, and sports.
The document discusses the mechanisms of polymerization, including chain growth and step growth polymerization. Chain growth polymerization involves the repeated addition of monomers with double or triple bonds to form polymers. Step growth polymerization occurs through condensation reactions between bifunctional or multifunctional monomers to form dimers, trimers, and eventually long chain polymers. The key mechanisms of chain growth polymerization, including free radical, cationic, and anionic polymerization are described. The mechanisms of step growth polymerization through condensation reactions are also outlined.
CHAPTER 9: Kinetics of chain and step growth polymerizationJacob Adrian
This document provides an outline and overview of step-growth and chain-growth polymerization mechanisms and kinetics. It discusses the step-growth mechanism, kinetics of step-growth polymerization using Carother's equation, and controlling molecular weight. It then covers the chain-growth mechanism, kinetics of chain-growth polymerization using steady-state kinetics, and examples of free radical polymerization initiation, propagation and termination reactions. Major classes of natural and commercial polymers are also briefly mentioned.
The document provides an introduction to polymers including definitions and classifications. It discusses that polymers are large molecules composed of repeating structural units called monomers. Polymerization is the process of forming polymers from monomers. Polymers can be classified based on their response to heat, type of polymerization reaction, chemical structure, and physical structure. The key properties of polymers like strength, plasticity, chemical resistance, physical state, glass transition temperature, and mechanical properties are also summarized. Finally, some major polymer-based industries like plastics, rubber, fibers, and coatings are listed.
This document discusses conducting polymers, which are polymers that conduct electricity. There are two types of conducting polymers: intrinsic and extrinsic. Intrinsic conducting polymers have conjugated double bonds in their backbone that allow for electron delocalization, while extrinsic polymers contain added conductive elements. Intrinsically, polymers can conduct due to thermal or light activation of electrons to overcome an energy gap (e.g. polyacetylene). Conductivity can also be increased through doping, which introduces positive or negative charges through oxidation or reduction of the polymer backbone. Conducting polymers have applications in rechargeable batteries, sensors, electronic devices, solar cells, and more.
Polymers are large molecules formed by combining many small molecules called monomers. There are two main types of polymerization: addition and condensation. Addition polymers form without releasing any byproducts while condensation polymers form with the release of small molecules like water. Polymers can be classified based on their source, structure, and thermal properties. Common polymerization techniques include bulk, solution, suspension, and emulsion which depend on factors like physical state and reaction mechanism. Bulk polymerization involves only monomer and initiator while solution polymerization dissolves the monomer in a solvent.
The document summarizes various mechanisms of polymerization, including chain-growth polymerization, step-growth polymerization, radical polymerization, cationic polymerization, anionic polymerization, coordination polymerization, Ziegler-Natta catalysis, ring-opening polymerization, and the polymerization of cyclic ethers, cyclic amides, and siloxanes. It discusses reaction initiation, mechanisms, applications, and stereochemistry for different polymerization methods.
Polymer chemistry involves the study of polymers, which are large molecules composed of many repeating structural units connected by covalent bonds. The monomers that make up polymers are linked through polymerization reactions. Polymers can be classified based on their structure, source, number of monomers, arrangement of monomers, and configuration. Common types of polymers include linear, branched, and cross-linked polymers. Polymers are also classified as natural, semi-synthetic, or synthetic based on their source. Polymerization reactions are either addition polymerization, involving chain growth, or condensation polymerization, involving step growth. Polymers have a variety of applications and properties depending on their structure and bonding forces.
This document provides an introduction to polymers. It discusses that polymers are formed through polymerization reactions where small monomer units join together to create large polymer molecules. There are two main types of polymerization - addition and condensation polymerization. Polymers can be classified as homopolymers, formed from one monomer, or copolymers, formed from multiple monomers. The document also discusses important polymer properties like glass transition temperature, molecular weight, types of polymers including thermoplastics and thermosets, and basic mechanical properties.
Polyimides are strong, heat and chemically resistant polymers formed from acid dianhydrides and diamines. They have applications as coatings, insulators, and mechanical parts due to their strength and durability. Polyimides are synthesized through a two-step polyaddition and dehydration reaction of acid anhydrides and diamines. They can replace metals and glass in applications due to their high heat resistance, strength, and transparency to microwaves.
Polymers are macromolecules formed by linking together small repeating units called monomers. There are two main types of polymerization: addition and condensation. Addition polymers are formed without the elimination of small molecules when monomers containing carbon-carbon double bonds polymerize via a chain reaction mechanism involving three steps: initiation, propagation, and termination. Condensation polymers are formed with the elimination of small molecules like water or ammonia when bifunctional monomers react. Common examples of addition polymerization include polyethylene formed from ethylene monomers using a free radical initiator like benzoyl peroxide.
Polyurethane is a polymer composed of organic units joined by carbamate links. It was first developed in the 1930s as a replacement for rubber. There are various types of polyurethanes including flexible foam, rigid foam, coatings, adhesives, sealants, elastomers and thermoplastic polyurethane. Polyurethanes are synthesized through the reaction of polyols with isocyanates. They have a wide range of applications including cushioning, insulation, automotive parts, footwear, packaging and medical devices due to their abrasion resistance, flexibility, toughness and other beneficial properties.
Polymers become conducting when they have conjugated double bonds along their carbon backbone that allow for electron movement. There are two types of conducting polymers - p-type polymers that conduct positive holes and n-type polymers that conduct negative electrons. Important examples include polyacetylene, polyaniline, and PEDOT. Potential applications of conducting polymers include uses in batteries, solar cells, LEDs, electromagnetic shielding, and anti-static coatings due to their ability to combine electrical conductivity with plastic-like mechanical properties.
Polymers are large molecules composed of repeating structural units called monomers connected by covalent bonds. There are two types of polymers: natural polymers found in living things, and synthetic polymers created through chemical processes. Some key points:
- Synthetic polymers can be divided into plastics, fibers, and elastomers. Common plastics include polyethylene, polyamide, and nylon.
- Polymer properties depend on factors like chain length, side groups, and cross-linking. Different polymers have various advantages and disadvantages for applications.
- Non-biodegradable synthetic polymers cause pollution problems if not properly disposed of or recycled. Methods to address this include reuse, reduction, recycling, and developing biode
Styrene-butadiene rubber (SBR) is a synthetic rubber derived from styrene and butadiene monomers. There are two main types: emulsion SBR produced via emulsion polymerization, and solution SBR produced via anionic polymerization. SBR has good abrasion resistance and aging stability when protected by additives. Approximately 50% of car tires are made from SBR, with higher styrene content rubbers being harder and less rubbery. Common applications of SBR include use in car tires, shoe soles, gaskets, and coated papers.
This report discusses polymers and polymer synthesis. It defines polymers as large molecules composed of repeating structural units or monomers joined by covalent bonds. Polymers are classified as natural, synthetic, or semi-synthetic. The report examines important natural polymers like cellulose as well as common synthetic polymers like polyethylene. It explores the manufacturing of plastics from different polymer types and polymerization reactions like addition and condensation that link monomers. In conclusion, polymers are ubiquitous materials that have revolutionized daily life due to their versatile properties and wide applications in areas like packaging and clothing.
Macromolecules are large molecules formed by linking many smaller units, or monomers, through covalent bonds. Natural substances like proteins and synthetic polymers are examples of macromolecules. Monomers undergo polymerization to form macromolecules by linking together through addition or condensation reactions. Polymers can be classified in different ways such as natural vs synthetic, organic vs inorganic, thermoplastic vs thermosetting, and linear, branched or cross-linked based on their molecular structure. The process of polymerization and properties of polymers depend on factors like the type of monomers, reaction conditions and molecular architecture.
This document provides an introduction to polymers. Polymers are macromolecules formed by linking many smaller molecules called monomers through a process called polymerization. Polymers can be classified based on their structure as linear, branched or cross-linked. Polymerization occurs through either addition or condensation reactions. Addition polymers are formed without the loss of small molecules, while condensation polymers are formed with the loss of small molecules like water or ammonia. Common examples of addition and condensation polymers are also provided.
The document discusses various topics related to polymers including their classification, physical properties, types of polymerization, and important polymers. It describes the different types of polymers based on their source, structure, molecular forces, and provides examples. The key types of polymerization covered are addition, condensation, copolymerization, cationic and anionic polymerization. Important polymers discussed include polyethylene, polypropylene, polyvinyl chloride and their properties and uses.
16. MIS for Project Monitoring and Evaluation ifadseahub
This document discusses how a management information system (MIS) can be used for project monitoring and evaluation (M&E). It describes how the MIS allows for:
1) Efficient data collection through mobile devices to track activities, evaluations, technology adoption, and fund utilization.
2) Real-time monitoring and analysis of project indicators and logframes for management and evaluation.
3) Visualization of project data and progress reports through maps and charts.
4) Future integration with other systems and flexibility to develop additional modules over time.
1) Polymers are large molecules formed from the combination of small molecules called monomers through a process called polymerization.
2) Polymerization is initiated by a reactive site on a monomer that is produced using an initiator. This allows monomers to add onto a growing polymer chain.
3) Polymers are classified based on their source, thermal properties, polymerization mechanism, and structure. Some examples of polymerization mechanisms discussed are chain-growth, step-growth, free radical, anionic, and cationic polymerization.
This document discusses polymers, including their classification, types of polymerization, characteristics, and applications. Polymers can be classified based on their source as natural, semi-synthetic, or synthetic. They can also be classified by their structure as linear, branched, or cross-linked. The two main types of polymerization are addition and condensation. Polymers have a variety of characteristics like low density and good corrosion resistance. They have wide applications in medicine, consumer products, industry, and sports.
The document discusses the mechanisms of polymerization, including chain growth and step growth polymerization. Chain growth polymerization involves the repeated addition of monomers with double or triple bonds to form polymers. Step growth polymerization occurs through condensation reactions between bifunctional or multifunctional monomers to form dimers, trimers, and eventually long chain polymers. The key mechanisms of chain growth polymerization, including free radical, cationic, and anionic polymerization are described. The mechanisms of step growth polymerization through condensation reactions are also outlined.
CHAPTER 9: Kinetics of chain and step growth polymerizationJacob Adrian
This document provides an outline and overview of step-growth and chain-growth polymerization mechanisms and kinetics. It discusses the step-growth mechanism, kinetics of step-growth polymerization using Carother's equation, and controlling molecular weight. It then covers the chain-growth mechanism, kinetics of chain-growth polymerization using steady-state kinetics, and examples of free radical polymerization initiation, propagation and termination reactions. Major classes of natural and commercial polymers are also briefly mentioned.
The document provides an introduction to polymers including definitions and classifications. It discusses that polymers are large molecules composed of repeating structural units called monomers. Polymerization is the process of forming polymers from monomers. Polymers can be classified based on their response to heat, type of polymerization reaction, chemical structure, and physical structure. The key properties of polymers like strength, plasticity, chemical resistance, physical state, glass transition temperature, and mechanical properties are also summarized. Finally, some major polymer-based industries like plastics, rubber, fibers, and coatings are listed.
This document discusses conducting polymers, which are polymers that conduct electricity. There are two types of conducting polymers: intrinsic and extrinsic. Intrinsic conducting polymers have conjugated double bonds in their backbone that allow for electron delocalization, while extrinsic polymers contain added conductive elements. Intrinsically, polymers can conduct due to thermal or light activation of electrons to overcome an energy gap (e.g. polyacetylene). Conductivity can also be increased through doping, which introduces positive or negative charges through oxidation or reduction of the polymer backbone. Conducting polymers have applications in rechargeable batteries, sensors, electronic devices, solar cells, and more.
Polymers are large molecules formed by combining many small molecules called monomers. There are two main types of polymerization: addition and condensation. Addition polymers form without releasing any byproducts while condensation polymers form with the release of small molecules like water. Polymers can be classified based on their source, structure, and thermal properties. Common polymerization techniques include bulk, solution, suspension, and emulsion which depend on factors like physical state and reaction mechanism. Bulk polymerization involves only monomer and initiator while solution polymerization dissolves the monomer in a solvent.
The document summarizes various mechanisms of polymerization, including chain-growth polymerization, step-growth polymerization, radical polymerization, cationic polymerization, anionic polymerization, coordination polymerization, Ziegler-Natta catalysis, ring-opening polymerization, and the polymerization of cyclic ethers, cyclic amides, and siloxanes. It discusses reaction initiation, mechanisms, applications, and stereochemistry for different polymerization methods.
Polymer chemistry involves the study of polymers, which are large molecules composed of many repeating structural units connected by covalent bonds. The monomers that make up polymers are linked through polymerization reactions. Polymers can be classified based on their structure, source, number of monomers, arrangement of monomers, and configuration. Common types of polymers include linear, branched, and cross-linked polymers. Polymers are also classified as natural, semi-synthetic, or synthetic based on their source. Polymerization reactions are either addition polymerization, involving chain growth, or condensation polymerization, involving step growth. Polymers have a variety of applications and properties depending on their structure and bonding forces.
This document provides an introduction to polymers. It discusses that polymers are formed through polymerization reactions where small monomer units join together to create large polymer molecules. There are two main types of polymerization - addition and condensation polymerization. Polymers can be classified as homopolymers, formed from one monomer, or copolymers, formed from multiple monomers. The document also discusses important polymer properties like glass transition temperature, molecular weight, types of polymers including thermoplastics and thermosets, and basic mechanical properties.
Polyimides are strong, heat and chemically resistant polymers formed from acid dianhydrides and diamines. They have applications as coatings, insulators, and mechanical parts due to their strength and durability. Polyimides are synthesized through a two-step polyaddition and dehydration reaction of acid anhydrides and diamines. They can replace metals and glass in applications due to their high heat resistance, strength, and transparency to microwaves.
Polymers are macromolecules formed by linking together small repeating units called monomers. There are two main types of polymerization: addition and condensation. Addition polymers are formed without the elimination of small molecules when monomers containing carbon-carbon double bonds polymerize via a chain reaction mechanism involving three steps: initiation, propagation, and termination. Condensation polymers are formed with the elimination of small molecules like water or ammonia when bifunctional monomers react. Common examples of addition polymerization include polyethylene formed from ethylene monomers using a free radical initiator like benzoyl peroxide.
Polyurethane is a polymer composed of organic units joined by carbamate links. It was first developed in the 1930s as a replacement for rubber. There are various types of polyurethanes including flexible foam, rigid foam, coatings, adhesives, sealants, elastomers and thermoplastic polyurethane. Polyurethanes are synthesized through the reaction of polyols with isocyanates. They have a wide range of applications including cushioning, insulation, automotive parts, footwear, packaging and medical devices due to their abrasion resistance, flexibility, toughness and other beneficial properties.
Polymers become conducting when they have conjugated double bonds along their carbon backbone that allow for electron movement. There are two types of conducting polymers - p-type polymers that conduct positive holes and n-type polymers that conduct negative electrons. Important examples include polyacetylene, polyaniline, and PEDOT. Potential applications of conducting polymers include uses in batteries, solar cells, LEDs, electromagnetic shielding, and anti-static coatings due to their ability to combine electrical conductivity with plastic-like mechanical properties.
Polymers are large molecules composed of repeating structural units called monomers connected by covalent bonds. There are two types of polymers: natural polymers found in living things, and synthetic polymers created through chemical processes. Some key points:
- Synthetic polymers can be divided into plastics, fibers, and elastomers. Common plastics include polyethylene, polyamide, and nylon.
- Polymer properties depend on factors like chain length, side groups, and cross-linking. Different polymers have various advantages and disadvantages for applications.
- Non-biodegradable synthetic polymers cause pollution problems if not properly disposed of or recycled. Methods to address this include reuse, reduction, recycling, and developing biode
Styrene-butadiene rubber (SBR) is a synthetic rubber derived from styrene and butadiene monomers. There are two main types: emulsion SBR produced via emulsion polymerization, and solution SBR produced via anionic polymerization. SBR has good abrasion resistance and aging stability when protected by additives. Approximately 50% of car tires are made from SBR, with higher styrene content rubbers being harder and less rubbery. Common applications of SBR include use in car tires, shoe soles, gaskets, and coated papers.
This report discusses polymers and polymer synthesis. It defines polymers as large molecules composed of repeating structural units or monomers joined by covalent bonds. Polymers are classified as natural, synthetic, or semi-synthetic. The report examines important natural polymers like cellulose as well as common synthetic polymers like polyethylene. It explores the manufacturing of plastics from different polymer types and polymerization reactions like addition and condensation that link monomers. In conclusion, polymers are ubiquitous materials that have revolutionized daily life due to their versatile properties and wide applications in areas like packaging and clothing.
Macromolecules are large molecules formed by linking many smaller units, or monomers, through covalent bonds. Natural substances like proteins and synthetic polymers are examples of macromolecules. Monomers undergo polymerization to form macromolecules by linking together through addition or condensation reactions. Polymers can be classified in different ways such as natural vs synthetic, organic vs inorganic, thermoplastic vs thermosetting, and linear, branched or cross-linked based on their molecular structure. The process of polymerization and properties of polymers depend on factors like the type of monomers, reaction conditions and molecular architecture.
This document provides an introduction to polymers. Polymers are macromolecules formed by linking many smaller molecules called monomers through a process called polymerization. Polymers can be classified based on their structure as linear, branched or cross-linked. Polymerization occurs through either addition or condensation reactions. Addition polymers are formed without the loss of small molecules, while condensation polymers are formed with the loss of small molecules like water or ammonia. Common examples of addition and condensation polymers are also provided.
The document discusses various topics related to polymers including their classification, physical properties, types of polymerization, and important polymers. It describes the different types of polymers based on their source, structure, molecular forces, and provides examples. The key types of polymerization covered are addition, condensation, copolymerization, cationic and anionic polymerization. Important polymers discussed include polyethylene, polypropylene, polyvinyl chloride and their properties and uses.
16. MIS for Project Monitoring and Evaluation ifadseahub
This document discusses how a management information system (MIS) can be used for project monitoring and evaluation (M&E). It describes how the MIS allows for:
1) Efficient data collection through mobile devices to track activities, evaluations, technology adoption, and fund utilization.
2) Real-time monitoring and analysis of project indicators and logframes for management and evaluation.
3) Visualization of project data and progress reports through maps and charts.
4) Future integration with other systems and flexibility to develop additional modules over time.
This topic relates to polymer structure and types of plastic. It also explains the usage and mechanical properties of thermo plastic, thermosetting plastic and the process of making plastic products.
The document discusses the thermal degradation of polymethyl methacrylate (PMMA). It states that PMMA degrades through depolymerization at temperatures above 300°C via radical chain reactions. The main reactions involved are initiation, depropagation, and termination, leading to a reduction in molecular weight and changes in physical properties. PMMA degradation yields methyl methacrylate monomer as the primary volatile product.
Acrylics are a family of transparent plastics that include polymethyl methacrylate (PMMA). PMMA was first synthesized in 1877 and commercialized in the 1930s for uses like aircraft canopies. It is produced through radical polymerization of methyl methacrylate. PMMA has good clarity, weatherability, and scratch resistance but limited chemical resistance. It finds wide use in glazing, lighting, medical devices, and coatings. Other acrylics include polyacrylamide, used as a flocculant and soil conditioner, and sodium polyacrylate, a super absorbent polymer used in diapers and water-retention products.
Blow molding is a manufacturing process that uses air pressure to form hollow plastic parts like bottles. There are three main blow molding processes: extrusion blow molding where a tube of molten plastic (parison) is captured in a mold and inflated, injection blow molding where a preform is first injection molded and then blown, and stretch blow molding where preforms are first made via injection molding and then reheated and blown into shape. Blow molding can make parts from various plastics like PET, HDPE, and PP. It is used widely to make containers and bottles for foods, drinks, chemicals and more.
Polymers are large molecules formed by combining many small repeating units called monomers. There are several types of polymers classified by their source, structure, and method of formation. Polymers can be natural, synthetic, or semi-synthetic and can have linear, branched, or cross-linked structures. Polymerization is the process where monomers combine to form polymers and can occur through addition, condensation, or copolymerization reactions. Key properties of polymers like glass transition temperature and tacticity depend on factors like molecular weight and stereochemistry of the repeating units.
This document discusses various topics related to timber, including:
- Definitions of timber, wood, and lumber
- Classification of trees as endogenous or exogenous
- Seasoning of timber through natural, kiln, chemical, or electric methods
- Common uses of timber in construction and manufacturing
- Defects in timber like heart shakes, star shakes, and knots
- Deterioration of timber through decay, insects, and fire
- Methods of preserving timber through oily and water-soluble preservatives applied by painting, dipping, or pressure processes
Timber comes from wood obtained from trees and is suitable for construction and other purposes. There are two main types of trees - exogenous and endogenous - with exogenous trees like conifers and deciduous trees most suitable for engineering. Timber has a macro structure visible to the eye like the pith, heartwood, and sapwood, as well as a micro structure only visible at high magnifications. Seasoning removes sap from fresh timber to make it stronger, lighter, and more durable. Common seasoning methods include natural, kiln, chemical and water seasoning. Timber is used widely in construction and manufacturing and can be preserved from damage using treatments like tar, paints, and chemical salts.
IT-as-a-Service Solutions for Healthcare ProvidersEMC
This white paper offers best practices regarding the technology infrastructure, business processes, and IT organizational structure to help healthcare providers maximize the value and impact of ITaaS across their organizations.
This white paper introduces the EMC Isilon scale-out data lake as the key enabler to store, manage, and protect unstructured data for traditional and emerging workloads.
This Frost & Sullivan analyst report reveals how the legal and threat environment, combined with BYOD and cost factors, make multi-factor, risk-based authentication the logical approach to solving the security challenges posed by threat actors.
True love has no ending, as a heart in love never loses hope in the promise of love regardless of time or distance. Friendship is like stars that are always there even when unseen, and friends should have great hopes, dreams, and expectations in each other. The recipe for a lifelong friendship includes sharing, caring, forgiveness, and tenderness.
Discover what’s new in Windows 8.1 regarding interface, settings, deployment, security, … How will Windows 8.1 fit in your enterprise? How do you upgrade? All answers are here!
All of material inside is un-licence, kindly use it for educational only but please do not to commercialize it.
Based on 'ilman nafi'an, hopefully this file beneficially for you.
Thank you.
The document discusses the economic concept of demand, including the determinants of demand and how demand curves shift in response to changes in price and other factors. It specifically addresses how demand for a good is affected by changes in the prices of substitutes and complements, as well as by changes in consumer tastes, income, population, and expectations about future prices. Graphs and examples are provided to illustrate these concepts.
The library offers help with APA and MLA citation styles for students stressed by the end of the term either by stopping by the library or texting/calling the provided numbers. The library is also hiring students to work in various positions.
This document discusses price controls and minimum wage. It notes that price ceilings and floors set by the government can cause shortages and surpluses that disrupt markets. Economists who support minimum wage argue it improves living standards for low-income families, while opponents argue it reduces job opportunities for low-skill workers and causes unemployment. Teenagers should pay attention to the debate as minimum wage policies directly impact youth employment opportunities.
1. Polymerization is the process of linking small molecules called monomers together to form large molecules called polymers. There are three main types of polymerization: addition, condensation, and copolymerization.
2. Plastics are polymers that can be molded into various shapes when heated and pressed. They have properties like low weight and resistance to corrosion that make them useful for many applications like automotive parts, electronics, and household goods.
3. Thermoplastics can be reshaped when heated while thermosets form permanent three-dimensional networks and cannot be remelted or remolded after initial forming.
This document discusses polymer science and technology. It provides an index of lecture slides covering topics like polymerization, compounding of plastics, and properties of plastics. Polymerization can occur through additional/chain polymerization, condensation/step polymerization, or copolymerization. Compounding involves mixing materials like plasticizers, fillers, and pigments with polymers to improve properties. Plastics are lightweight materials that can be molded into various shapes. They have properties like low cost, corrosion resistance, and easy fabrication but also have weaknesses such as poor heat resistance.
Polymers are long chain molecules made of repeating monomer units. They can be classified based on their origin as natural or synthetic, and based on their structure as linear, branched or cross-linked. Polymer properties depend on factors like molecular weight, degree of cross-linking, temperature and addition of fillers. Polymers are prepared by addition polymerization which involves free radical or ionic chain reactions, or condensation polymerization which produces polymers and small molecule byproducts. Polymerization can be inhibited by materials that react with radicals like oxygen or eugenol. Polymers exist as hard amorphous solids, hard crystalline solids, rubbers or fibers depending on their molecular structure and processing.
This document provides information about polymers and polymerization. It defines a polymer as a long molecule formed by joining thousands of small monomer units through chemical bonds. The degree of polymerization refers to the number of repeating monomer units in the polymer chain. Polymers can be classified based on their source, structure, tacticity, monomer units, end uses, conductance, environmental impact, and behavior when heated. The two main types of polymerization are addition polymerization and condensation polymerization. Examples of daily use polymers like polyethylene, polyvinyl chloride, nylon, bakelite etc. are also discussed along with their properties and applications.
Introduction to pharmaceuitcal polymer chemistryGanesh Mote
The document discusses various types of polymers including their structure, properties, and uses. It defines a polymer as a large molecule formed by the repeated linking of small molecules called monomers. Polymers can be classified based on their source, structure, molecular forces, and mode of polymerization. Common polymers discussed include polyethylene, polypropylene, polystyrene, polyvinyl chloride, teflon, and poly(methyl methacrylate). Their properties and applications in various industries are also summarized.
The document discusses various types of polymers including thermoplastics like polyethylene, polypropylene, polyvinyl chloride, polystyrene; thermosetting plastics; polymerization methods like addition, condensation and their mechanisms; classification of polymers; properties and applications of common polymers like polyethylene, polystyrene, polyvinyl chloride and teflon. It also discusses polymer structure, degree of polymerization, tactics and various additives used in plastics.
Polymers are macromolecules formed by combining many small molecules (monomers) through covalent bonds. Common examples include polyethylene, polypropylene, polyvinyl chloride, nylon, and rubber. Polymers can be classified based on their source (natural, semi-synthetic, synthetic), structure (linear, branched, cross-linked), or the polymerization process used to create them (addition, condensation). Polymerization involves monomers combining in chains through addition or condensation reactions with or without the loss of small molecules as byproducts. The type of polymerization determines the properties and applications of the resulting polymers.
This document provides information on the objectives and outcomes of chemistry courses related to materials chemistry, polymers, and elastomers. The courses aim to help students correlate material properties with internal structure, apply principles of electrochemistry and corrosion prevention, and discuss different types of polymers for engineering applications. Specific topics covered include polymerization reactions, polyvinyl chloride, bakelite, nylon-6,6, Kevlar, and elastomers. After completing the courses, students will be able to analyze and apply concepts related to batteries, water treatment, corrosion prevention, and different types of polymers and their uses.
Synthetic polymers are widely used as substitutes for materials like metals, wood, cotton and glass. They have properties like low density, resistance to chemicals, flexibility and the ability to be molded into different shapes. Common synthetic polymers include polyethylene, polyester, nylon and polypropylene. Polymers can be thermoplastics, which soften when heated and harden when cooled, allowing reshaping, or thermosets, which remain rigid. Conductive polymers can transport electricity through conjugated pi electrons on their backbone, making them semiconductors when doped. Applications include medical devices, packaging and conductive fabrics.
Polymers are large molecules composed of repeated chemical units. The smallest repeating unit is called monomer (mono [Single] + mer [part]). The word polymer is derived from the Greek word „poly‟ = many; mers = parts. It is generally described in terms of single repeated units
This document discusses polymers, including their classification, types of polymerization, characteristics, and applications. Polymers can be classified based on their source, structure, polymerization method, or molecular forces. The main types of polymerization are addition and condensation. Polymers have properties like low density, corrosion resistance, and moldability. They are used widely in applications such as medicine, consumer products, industry, and sports equipment.
The document discusses various topics related to polymerization including:
1. Definitions of polymerization, degree of polymerization, and different polymerization mechanisms including addition, condensation, and co-polymerization.
2. Addition polymerization involves monomers adding to the growing chain without byproducts, while condensation polymerization eliminates molecules like water as monomers join.
3. Common polymerization techniques are discussed briefly, including bulk, solution, suspension, and emulsion polymerization.
Plastic is a polymer material made from carbon and hydrogen that can be molded into shapes when heat and pressure are applied. Early plastics like celluloid and Bakelite were developed in the 1800s-1900s, but plastic use expanded in the 20th century. Plastics can be thermoplastics, which can be remelted and reshaped, or thermosets, which set permanently after initial molding. Common plastics are made through polymerization of monomers into chains or networks and have properties like strength, durability, and electrical insulation. Plastics are widely used for their processability, low cost, and ability to be formed into complex shapes.
1. Plastics are organic polymer materials made from carbon and hydrogen that can be molded under heat and pressure into desired shapes that retain their form when cooled.
2. Early plastics included Parkesine in 1855, celluloid in 1866, and Bakelite in 1907.
3. Plastics are classified as thermoplastics, which can be remelted and reshaped, and thermosets, which set permanently and cannot be remelted once formed. Common thermoplastics include polyethylene, polyvinyl chloride, and nylon, while popular thermosets include epoxy, polyester, and phenol formaldehyde.
Polymers play a very important role in human life. Our body is made of lot of polymers, e.g. Proteins, enzymes, etc. Other naturally occurring polymers like wood, rubber, leather and silk are have wide application. Now a day synthetic polymer like useful plastics, rubbers and fiber materials are synthesized. presentation includes introduction classification and preparation methods. Polymers play a very important role in human life. Our body is made of lot of polymers, e.g. Proteins, enzymes, etc. Other naturally occurring polymers like wood, rubber, leather and silk are have wide application. Now a day synthetic polymer like useful plastics, rubbers and fiber materials are synthesized. Leo Baekeland patented the first totally synthetic polymer called Bakelite (1910). Bakelite is a versatile, durable material prepared from low-cost materials phenol and formaldehyde and was the most important synthetic polymer material. In the 1920s Hermann Staudinger showed that polymers were high-molecular-weight compounds held together by normal covalent bonds.
The suffix in polymer ‘mer’ is originated from Greek word meros – which means part. The word polymer is thus coined to mean material consisting of many parts or mers. A macromolecule having high molecular mass (103-107u) and generally not a well-defined structure or molecular weight. The macromolecules formed by joining of repeating structural units on a large scale. The repeating structural units are simple and reactive molecules linked to each other by covalent bonds. This process of formation of polymers from respective monomers is called polymerization. Most of the polymers are basically organic compounds, however they can be inorganic (e.g. silicones based on Si-O network).
This document provides an overview of polymers, including:
- Polymers are large molecules made by linking repeating units called monomers. Naturally occurring polymers have been used for thousands of years, while artificial polymers were developed more recently after WWII.
- Polymers can be classified based on their source, thermal behavior, chemical structure, stereochemistry, and end use. Important types include thermoplastics, thermosets, homopolymers, copolymers, fibers, and plastics.
- Polymer properties depend on factors like strength, crystallinity, elasticity, and glass transition temperature which are influenced by the polymer structure. Common characterization techniques and molding processes like injection molding are also discussed.
Polymer - a long chain molecule made up of many small identical units of Monomer is known as Polymer.
Monomer - the smallest repeating unit is known as Monomer.
Polymer is a molecule is obtained by natural and synthetic origin having group of Smallest repeating unit is known as polymer.
Polymer is important for increasing the stability of drug molecule, it is important to influencing the solubility of drug molecule, it is important to maintain the Physicochemical properties, it is important to maintain the prolong stability of drug molecule in extended period of time, it is important for influencing the Bioavailability of drug.
Polymer is important for Pharmaceutical industries and research purpose.
1. The document discusses polymers, their types including plastics, elastomers, fibers, and composites.
2. Key polymerization reactions are addition polymerization which does not eliminate small molecules, and condensation polymerization which eliminates molecules like water.
3. Common polymers discussed include nylon, polyethylene, polyester, rubber and fibers like nylon-6,6 and terylene. Composites contain a matrix and dispersed strengthening phase.
The document discusses polymers, which are high molecular mass substances formed by joining repeating structural units known as monomers via covalent bonds. Polymers can be homopolymers formed from a single monomer or copolymers formed from multiple monomers. They are classified based on source, structure, mode of polymerization, molecular forces, and growth mechanism. Addition or chain growth polymerization involves monomers with double/triple bonds adding in a chain reaction, while condensation or step growth polymerization forms polymers through condensation reactions between bifunctional monomers with the elimination of small molecules. Common synthetic polymers include polyethylene, polyvinyl chloride, and nylon.
Fueling AI with Great Data with Airbyte WebinarZilliz
This talk will focus on how to collect data from a variety of sources, leveraging this data for RAG and other GenAI use cases, and finally charting your course to productionalization.
HCL Notes and Domino License Cost Reduction in the World of DLAUpanagenda
Webinar Recording: https://www.panagenda.com/webinars/hcl-notes-and-domino-license-cost-reduction-in-the-world-of-dlau/
The introduction of DLAU and the CCB & CCX licensing model caused quite a stir in the HCL community. As a Notes and Domino customer, you may have faced challenges with unexpected user counts and license costs. You probably have questions on how this new licensing approach works and how to benefit from it. Most importantly, you likely have budget constraints and want to save money where possible. Don’t worry, we can help with all of this!
We’ll show you how to fix common misconfigurations that cause higher-than-expected user counts, and how to identify accounts which you can deactivate to save money. There are also frequent patterns that can cause unnecessary cost, like using a person document instead of a mail-in for shared mailboxes. We’ll provide examples and solutions for those as well. And naturally we’ll explain the new licensing model.
Join HCL Ambassador Marc Thomas in this webinar with a special guest appearance from Franz Walder. It will give you the tools and know-how to stay on top of what is going on with Domino licensing. You will be able lower your cost through an optimized configuration and keep it low going forward.
These topics will be covered
- Reducing license cost by finding and fixing misconfigurations and superfluous accounts
- How do CCB and CCX licenses really work?
- Understanding the DLAU tool and how to best utilize it
- Tips for common problem areas, like team mailboxes, functional/test users, etc
- Practical examples and best practices to implement right away
Unlock the Future of Search with MongoDB Atlas_ Vector Search Unleashed.pdfMalak Abu Hammad
Discover how MongoDB Atlas and vector search technology can revolutionize your application's search capabilities. This comprehensive presentation covers:
* What is Vector Search?
* Importance and benefits of vector search
* Practical use cases across various industries
* Step-by-step implementation guide
* Live demos with code snippets
* Enhancing LLM capabilities with vector search
* Best practices and optimization strategies
Perfect for developers, AI enthusiasts, and tech leaders. Learn how to leverage MongoDB Atlas to deliver highly relevant, context-aware search results, transforming your data retrieval process. Stay ahead in tech innovation and maximize the potential of your applications.
#MongoDB #VectorSearch #AI #SemanticSearch #TechInnovation #DataScience #LLM #MachineLearning #SearchTechnology
Trusted Execution Environment for Decentralized Process MiningLucaBarbaro3
Presentation of the paper "Trusted Execution Environment for Decentralized Process Mining" given during the CAiSE 2024 Conference in Cyprus on June 7, 2024.
Taking AI to the Next Level in Manufacturing.pdfssuserfac0301
Read Taking AI to the Next Level in Manufacturing to gain insights on AI adoption in the manufacturing industry, such as:
1. How quickly AI is being implemented in manufacturing.
2. Which barriers stand in the way of AI adoption.
3. How data quality and governance form the backbone of AI.
4. Organizational processes and structures that may inhibit effective AI adoption.
6. Ideas and approaches to help build your organization's AI strategy.
Have you ever been confused by the myriad of choices offered by AWS for hosting a website or an API?
Lambda, Elastic Beanstalk, Lightsail, Amplify, S3 (and more!) can each host websites + APIs. But which one should we choose?
Which one is cheapest? Which one is fastest? Which one will scale to meet our needs?
Join me in this session as we dive into each AWS hosting service to determine which one is best for your scenario and explain why!
This presentation provides valuable insights into effective cost-saving techniques on AWS. Learn how to optimize your AWS resources by rightsizing, increasing elasticity, picking the right storage class, and choosing the best pricing model. Additionally, discover essential governance mechanisms to ensure continuous cost efficiency. Whether you are new to AWS or an experienced user, this presentation provides clear and practical tips to help you reduce your cloud costs and get the most out of your budget.
Skybuffer SAM4U tool for SAP license adoptionTatiana Kojar
Manage and optimize your license adoption and consumption with SAM4U, an SAP free customer software asset management tool.
SAM4U, an SAP complimentary software asset management tool for customers, delivers a detailed and well-structured overview of license inventory and usage with a user-friendly interface. We offer a hosted, cost-effective, and performance-optimized SAM4U setup in the Skybuffer Cloud environment. You retain ownership of the system and data, while we manage the ABAP 7.58 infrastructure, ensuring fixed Total Cost of Ownership (TCO) and exceptional services through the SAP Fiori interface.
Building Production Ready Search Pipelines with Spark and MilvusZilliz
Spark is the widely used ETL tool for processing, indexing and ingesting data to serving stack for search. Milvus is the production-ready open-source vector database. In this talk we will show how to use Spark to process unstructured data to extract vector representations, and push the vectors to Milvus vector database for search serving.
A Comprehensive Guide to DeFi Development Services in 2024Intelisync
DeFi represents a paradigm shift in the financial industry. Instead of relying on traditional, centralized institutions like banks, DeFi leverages blockchain technology to create a decentralized network of financial services. This means that financial transactions can occur directly between parties, without intermediaries, using smart contracts on platforms like Ethereum.
In 2024, we are witnessing an explosion of new DeFi projects and protocols, each pushing the boundaries of what’s possible in finance.
In summary, DeFi in 2024 is not just a trend; it’s a revolution that democratizes finance, enhances security and transparency, and fosters continuous innovation. As we proceed through this presentation, we'll explore the various components and services of DeFi in detail, shedding light on how they are transforming the financial landscape.
At Intelisync, we specialize in providing comprehensive DeFi development services tailored to meet the unique needs of our clients. From smart contract development to dApp creation and security audits, we ensure that your DeFi project is built with innovation, security, and scalability in mind. Trust Intelisync to guide you through the intricate landscape of decentralized finance and unlock the full potential of blockchain technology.
Ready to take your DeFi project to the next level? Partner with Intelisync for expert DeFi development services today!
Programming Foundation Models with DSPy - Meetup SlidesZilliz
Prompting language models is hard, while programming language models is easy. In this talk, I will discuss the state-of-the-art framework DSPy for programming foundation models with its powerful optimizers and runtime constraint system.
Ivanti’s Patch Tuesday breakdown goes beyond patching your applications and brings you the intelligence and guidance needed to prioritize where to focus your attention first. Catch early analysis on our Ivanti blog, then join industry expert Chris Goettl for the Patch Tuesday Webinar Event. There we’ll do a deep dive into each of the bulletins and give guidance on the risks associated with the newly-identified vulnerabilities.
Your One-Stop Shop for Python Success: Top 10 US Python Development Providersakankshawande
Simplify your search for a reliable Python development partner! This list presents the top 10 trusted US providers offering comprehensive Python development services, ensuring your project's success from conception to completion.
Your One-Stop Shop for Python Success: Top 10 US Python Development Providers
Unit 3-polymers
1. POLYMERS
Polymer is a macro molecule formed by the union of many small molecules.
Depending upon the structure, a polymer may be linear or branched.
Ex. – CH2 – CH2 – CH2--Si – O – Si – O - Si
Polyethylene |
Linear CH2- Si – O – Si – O –
Branched silicon resin.
Depending type of monomer, they may be homopolymer (made up of same monomer) or
Co-polymer (made up of different monomers)
O O
Ex. – CH2 – CH2 - n H 2N – (CH2)6 – NH – C – (CH2)4 – C – NH -
Homopolymer Nylon 6,6
Polyethylene (Co-polymer)
POLYMERISATION: It may be defined as the process of linking or joining together small molecules like
monomers to make large molecules.
Basically there are 3 types of polymerizations.
1. Additional polymerization or Chain polymerization
2. Condensation polymerization or Step polymerization
3. Copolymerization
1. Additional polymerization or Chain polymerization: This polymerization yields an exact multiple
of basic monomeric molecules. This monomeric molecule contains one or more double bonds. By
intermolecular rearrangement of these double bonds makes the molecule bifunctional. In this
polymerization process light, heat and pressure or catalyst is used to breakdown the double covalent
bonds of monomers.
2. Condensation polymerization or Step polymerization: May be defined as “a reaction occurring
between simple polar-group-containing monomers with the formation of polymer and elimination of
small molecules like water, HCl, etc.” For example, hexamethylene diamine and adipic acid condense
to form a polymer, Nylon6:6.
Additional polymerization is a chain reaction converting of a sequence of three steps. Initiation,
propagation and termination.
a. Initiation step is considered to involve two reactions. The first is the production of free radicals, usually,
by the hemolytic dissociation of an initiator (or catalyst) to yield a pair of radicals R’.
I 2R’ ………(1)
(Initiator) (Free radicals)
The second part of initiation under the addition of this radical to the just moment molecule (M) to produce the
chain initiating species M1.
R + M M1 ……….(2)
Free radical monomer molecule
Polymer Science (Unit-III) 1 Prepared by B.SRINIVAS
2. Thus the polymerization of monomer CH2 = CHY taken in the form.
H
R + CH2 = CHY R- CH2 – C
R
b. Propagation step: Consists of the growth of M1 by successive additions of large numbers of monomer
molecules according to equation.
M1 + M M2
M2 + M M3
M3+ M M4 or in general terms Mn + M Mn + 1
c. Termination step: At some time, the propagation polymer chain steps growing and terminates.
H H H H
- CH2 – C + C – CH2 - CH2 – C – C – CH2
Y Y Y Y
Disproportion in which a hydrogen atom of one radical center is transferred to another radical center. This
results in the formations of two polymer molecules, are saturated and one unsaturated e.g.
H H H H H
CH2 – C + C – CH2 CH2 – CH + C = C –
Y Y Y Y
The two different modes of terminations can be represented in general terms by:
M*n + M*m M*n+m (Coupling)
* *
M n + Mm Mn + Mm (Disproportionation)
Co-polymerization: Polymerization involving two different monomers.
Ex. Polymerization of butadiene and styrene to gave Buna –S.
H
CH2 = CH – CH = CH2 + nx CH2 = CH –Ph -C -CH = CH –CH - -CH2 –CH -
1,3-butadiene (75%) Styrene(25%) H x Ph n
Q.No.1: Write the differences between a) Additional – condensation polymerization b) Thermo-set-
Thermoplastics c) compressions-Injection moulding.
a. Difference between additional & condensation polymerization:
Additional polymerization Condensation polymerization
1. Additional polymerization also known as Chain polymerization 1. Condensation polymerization
2. This polymerization yields an exact multiple of basic monomeric also known as Step polymerization
molecules. This monomeric molecule contains one or more double 2. This polymerization reaction
bonds. occurring between simple polar-
By intermolecular rearrangement of these double bonds makes the group-containing monomers with
molecule bi-functional. the formation of polymer and
In this polymerization process light, heat and pressure or catalyst is elimination of small molecules
used to breakdown the double covalent bonds of monomers. like water, HCl, etc.”
Eg. Polymerization of ethylene at 1500 atm and a temperature 150 Eg. Hexamethylene diamine and
– 250 0C in presence of traces of oxygen formation of polyethylene.
adipic acid condenses to form a
polymer, Nylon6:6.
Polymer Science (Unit-III) 2 Prepared by B.SRINIVAS
3. b. Difference between thermo set and thermoplastics.
Plastics are materials that show the property of plasticity and can be moulded into any desired shape
and dimension of articles by the application of heat and pressure.
Thermoplastics Thermoset plastics
1.These are processed by addition polymerization. 1. These are proceed by condensation
2.Softens on heating and retaining the same chain Polymerization.
on cooling. 2. These are infusible and insoluble
3.They are along chain linear polymers without mass on heating i.e., heat resistance.
any branched or cross linked chain. 3. They are branched or cross-linked
4.On repeated heating and cooling, there is no Polymer.
4. Some sort of chemical changes occur
change in chemical nature.
On heating.
5.These plastics undergo purely physical process. 5.These Plastics undergo physical as well
As chemical process.
6.By heating the plastics, thy can be proceed.
6. These plastics cannot be proceeding by
7.Waste thermoplastics can be recovered. heating.
7. Waste thermosetting cannot be recovered.
c. Differences between compression and injection moulding techniques:
Compression Moulding Injection moulding
1. The plastic ingredient in proper 1. In this, the heated plastic is injected into the
Proportions are filled in between the two half mould cavity from where it is cooled and taken
portions of the mould. These portions are out.
moved relative to each other and by the
applying heat and pressure, the part can be
manufactured. 2. It is applicable to thermoplastic resins.
2. It is applicable to both thermoplastic and
thermosetting plastic resins 3. Moulding is somewhat complicated compared
3. Moulding is often simpler. to compression moulding.
4. It is less expensive. 4. It is expensive
5. Require more operation time. 5. Require less operation time
6. Less production rate. 6. High Production rate.
7. There is no limitation to the design of articles 7. There is limitation to the design of articles to be
to be moulded. moulded.
8. High moulding cost. 8. Less moulding cost.
Polymer Science (Unit-III) 3 Prepared by B.SRINIVAS
4. Q. No. 2: a. Define Plastic? Describe plastics compounding & its ingredients.
b. Describe various types of (compression, injection, extrusion & transfer ) moulding & fabrication
process
a. Plastics are the materials that show the property of plasticity and can be moulded into any
desired shape and dimensions by the application of heat and pressure. Plastics having variety of properties are
in use in present applications. The properties are low thermal and electrical conductivities, easy to fabricate,
low specific gravity etc. The plastics can be fabricated for large number of colours and can be used for
decorative purpose. Plastics can be used to produce complicated shapes and accurate dimensions very cheaply
by moulding process. Plastics are generally used for making automobile parts, goggle, telephones, electrical
instruments, optical instruments, household appliances etc. plastics having high wear resistance properties can
be used for making gears, bearings etc.
Merits of Plastics
1. Plastics have good shock absorption capacity compared with steel.
2. Plastics have high abrasion resistance.
3. Plastics are chemically inert.
4. Plastics have high corrosion resistance compared to metals.
5. Mounding, machining, drilling etc. can be easily done on plastic materials.
6. Plastics are light in weight having specific gravity from 1 to 2, 4.
7. Plastics can be made according to the order like hard, soft, rigid, tough, brittle, malleable etc.
8. Fabrication of plastics into desired shape and size is cheap.
9. Plastics are dimensionally stable.
10. Plastics are don’t absorb water.
11. Thermal coefficient of expansion of plastic is low.
12. Excellent outer finish can be obtained on plastic products.
Demerits of Plastics
1. Plastics are soft 4. Cost of plastics is high.
2. Plastics have poor ductility. 5. Plastics can deform under load.
3. Resistance to heat is less.
Compounding of plastics:
Compounding of the plastics may be defined as the mixing of different materials like
plasticizers, fillers of extenders, lubricants, dies and pigments to the thermoplastic and thermosetting plastics
to increase their useful properties like strength, toughness, etc. Resins have plasticity or binding property, but
need other ingredients to be mixed with them for fabrication into useful shapes.
Polymer Science (Unit-III) 4 Prepared by B.SRINIVAS
5. Ingredients used in compounding of plastics
Some of the ingredients used in compounding of plastics are
i) Resins
ii) Plasticizers.
iii) Fillers or extenders.
iv) Dyes and pigments.
v) Lubricants.
i). Resins: Resin is the binder, which holds the different constituents together. Thermosetting resins are, usually,
supplied as linear-polymers of comparatively low molecular-weight, because at this stage they are fusible and
hence, mouldable. The conversion of this fusible form into cross-linked infusible form takes place, during
moulding itself, in presence of catalysts, etc.
ii. Plasticizers
Plasticizers are substances added to enhance the plasticity of the material and to reduce the
cracking on the surface. Plasticizers are added to the plastics to increase flexibility and toughness. Plasticizers
also increase the flow property of the plastics.
Example: Dibutytyle oxalate, Castor oil and Tricresyl phosphate
iii). fillers or Extenders
Fillers are generally added to thermosetting plastics to increase elasticity and crack resistance. Fillers
improve thermal stability, strength, non combustibility, water resistance, electrical insulation properties and
external appearance.
Example: wood flour, Asbestos, Mica, Cotton, Carbon black, Graphite, Barium sulphate etc.
iv) Dyes and pigments
These are added to impart the desired colour to the plastics and give decorative effect.
v) Lubricants
These are added to prevent the plastics from sticking to the moulds.
Example: Oils, Waxes, Soaps etc.
Thus the objective of compounding is to improve the properties of the basic resin, such that the
fabrication is made easy.
b. Fabrication of plastics:
Many methods of fabricating plastics into desired shaped articles are employed. This production of plastics is
known as fabrication of plastics. The methods, usually depends upon the types of resins used i.e., whether
thermosetting or thermoplastic. Different fabrication techniques are described below.
Moulding of Plastics
Moulding of plastics comprises of forming an article to the desired shape by application of heat and
pressure to the moulding compounds in a suitable mould and hardening the material in the mould. The method
of moulding depends upon the type of resins used.
i) Compression moulding:
This method is applied to both thermoplastic and thermosetting resins. The predetermined quantity of plastic
Ingredients in proper properties are filled between the two half –pieces of mould which are capable of being
moved relative to each other heat and pressure are than applied according to specifications. The containers
filled with fluidized plastic. Two halves are closed very slowly. Finally curing is done either by heating or
cooling. After curing the moulded article is taken out by opening the mould parts.
Polymer Science (Unit-III) 5 Prepared by B.SRINIVAS
6. ii) Injection moulding:
In this method, the moulding plastic powder is fed into a heated cylinder from where it is injected at a
controlled rate into the tightly locked mould by means of a screw arrangement or by a piston plunger. The
mould is kept cold to allow the hot plastic to cure and become rigid. When the materials have been cured
sufficiently, half of the mould is opened to allow the injection of the finished article without any deformation,
etc. Heating is done by oil or electricity.
iii) Transfer moulding:
In this method, the principle is like injection moulding. The moulding powder is heated in a chamber to
become plastic. Later it is injected into a mould by plunger working at high pressure through orifice. Due to
this heat is developed and the plastic melts, takes the shape of the mould.
d) Extrusion moulding:
This process is useful in the preparation of continuous wires with uniform cross section. The heated plastic is
pushed into the die with the help of screw conveyor. In the die, the plastic gets cooled due to the exposure to
atmosphere and by artificial air jets.
Extrusion moulding is used mainly for continuous moulding of thermoplastic materials into articles of
uniform cross section like tubes, rods, strips, insulated electric cables. The thermoplastic ingredients are
heated to plastic condition and then pushed by means of a screw conveyor into a die, having the required outer
shape of the article to the manufactured. Here the plastic mass gets cooled, due to the atmospheric exposure
(or artificially by air jets). A long conveyor carries away continuously the cooled product.
Polymer Science (Unit-III) 6 Prepared by B.SRINIVAS
7. Q.No.3: a. Identify the thermosets & thermoplastics among the following: PVC, polyethylene, silicon,
polyester fiber, bakelite.
b. What is Bakelite? How is it manufactured and mention its uses.
c. Describe the manufacture, properties, and uses of Nylon.
Answer: a. Thermoplastics: PVC & Polyethylene
Thermo-sets plastics: silicon, Polyester fiber & Bakelite
b. Bakelite: It is prepared by condensing phenol with formaldehyde in presence of acidic/alkaline
catalyst.
The initial reaction results in the formation of O- and P- hydroxyl methyl/phenol which reacts to
form linear polymer. During modeling hexamethylene tetramine is added, which converts to insoluble solid of
cross-linked structure Bakelite.
Applications: It is used for making electric insulator parts like switches, plugs, switch boards etc. For making
moulded articles like telephone parts cabinet of radio and television.
c. Polyamides: Synthetic fiber forming polyamides are also known as ‘Nylons’.
Nylon-6: Preparation: Nylon-6 can be made by self condensation of ε-amino caproic acid.
H2N-(CH2)5-COOH -[-NH-(CH2)5-CO-]n- + H2O
ε-amino caproic acid. Nylon-6
Nylon-6,6: It is prepared by Hexamethylene diamine and Adipic acids are polymerized in 1:1 ratio.
Properties:
a. The structure of nylons are linear that permits side-by-side alignment. Moreover, the molecular chains are
held together by hydrogen bonds. Thus, nylons have high crystalline which imparts high strength, high
melting point, elasticity, toughness, abrasion resistance and retention of good mechanical properties upto
1250C.
b. They are also sterilisable.
c. Since nylons are polar polymers, they have good hydrocarbon resistance. Larger the number of carbon
atoms, greater will be ease of processing and hydrocarbon and moisture resistance.
Applications:
Nylon-6,6 is primarily used for fibers, which find use in making socks, under-garments, carpets.
Nylon-6.6 is also used in mechanical engineering for well known applications like gears, bearings, bushes,
cams.
Nylon-6 is mainly used in manufacture of tyre cord.
Nylon6-10 is suitable for monofilaments which are used for bristles, brushes.
Polymer Science (Unit-III) 7 Prepared by B.SRINIVAS
8. Q.No.4: Describe the manufacture, properties, uses of a) polyethylene
b) PVC c) Teflon d) PS
Answer: Polyethylene: This can be obtained by the polymerization of ethylene at 1500 atm and a
0
temperature 150 – 250 C in presence of traces of oxygen.
Polyethylene also known as polyethene. It is prepared by the process of addition polymerization of ethylene.
Polyethylene is two types on the basis of density.
a. Low density polyethylene(LDPE):
Preparation: it is prepared by polymerizing ethylene at high pressures of 1000 to 5000 atmospheres and at 250 0C
in the presence of free radical initiator (Oxygen).
Properties: LDPE molecules are branched and don’t allow the molecules to pack efficiently.
LDPE has a density 0.91 to 0.925 g/cm 3
LDPE Crystalline nature is also low (55%)
LDPE is chemically inert and has good chemical resistance.
LDPE is non-polar; hence it has excellent electrical insulation properties.
LDPE is tough and flexible even at low temperatures.
Uses: LDPE is used in following applications:
a. Films for general packing and carrier bags.
b. Squeeze bottles particularly for detergents.
c. Moulded toys & gift articles
d. Ink tubes for pens & Mugs.
b. High density polyethylene (HDPE):
Preparation: it is prepared by polymerizing under 6 -7 atmospheric pressure at 60 – 70 0C in the presence of
Zeigler – Natta (TiCl4 + Al(C2H5)3) as a catalyst.
Properties: The HDPE molecules are linear and their packing is very easy.
HDPE has a density 0.941 to 0.965 g/cm 3
HDPE has excellent chemical resistance.
HDPE has excellent electrical insulation properties.
HDPE has sufficiently low water and gas permeability.
HDPE is free from odour and toxicity.
HDPE is stiffer, hard and possesses greater tensile strength.
Polymer Science (Unit-III) 8 Prepared by B.SRINIVAS
9. Applications: HDPE film is used as wrapping material instead of paper for food products.
HDPE used for the manufacture of crates, food tubs, industrial containers & over head tanks.
HDPE can also be used for domestic water & gas piping.
HDPE can also used for milk bottles, house hold chemicals and drug packing.
PVC :
Poly Vinyl Chloride is obtained by heating a water emulsion of vinyl chloride in presence of a small amount
of benzoyl peroxide or hydrogen peroxide in an auto clave under pressure.
Vinyl chloride, so needed is generally prepared by treating acetylene at 1 to 1.5 atmospheres with hydrogen
chloride at 600C to 800C in the presence of metal chloride as catalyst.
CH = CH + HCl CH2 = CH Cl
Acetylene Vinyl chloride
Properties: It occurs as a colourless rigid material.
It is having high density and low softening point.
It is resistant to light, atmospheric oxygen, inorganic acids and alkalis.
It is most widely used synthetic plastic.
Uses: It is mainly used as cable insulation, leather cloth, packing and toys.
It is used for manufacturing of film, sheet and floor covering.
PVC pipes are used for carrying corrosive chemicals in petrochemical factories.
TEFLON OR Poly tetra fluoro ethylene:
Teflon is obtained by polymerization of water-emulsion tetrafluoroethylene, under pressure in presence of
benzoyl peroxide as catalyst.
Properties: Due to the presence of highly electronegative fluorine atoms and the reqular configuration of the
polytetrafluoro ethylene molecule results in very strong attractive forces between the different chains.
These strong attractive forces give the material extreame toughness, high softening point, exceptionally high
chemical-resistance towards all chemicals, high density, waxy touch, and very low coefficient of friction,
extremely good electrical and mechanical properties: It can be machined, punched and drilled. The material,
however, has the disadvantage that it cannot be dissolved and cannot exist in a true molten state. Around
3500c, it sinters to form very viscous, opaque mass, which can be moulded into certain forms by applying high
pressures.
Uses: as insulating material for motors, transformers, cables, wires, fittings, etc, and for making gaskets,
packing, pump parts, tank linings, chemical-carrying pipes, tubing’s and tanks, etc,; for coating and
impregnating glass fibres, asbestos fibres and cloths; in non-lubricating bearings and non-sticking stop-cocks
etc.
Polymer Science (Unit-III) 9 Prepared by B.SRINIVAS
10. Polystyrene:
Preparation: Polystyrene is prepared by free radical addition polymerization of styrene in the presence of
benzoyl peroxide as catalyst.
Properties:
i. Because of the presence of bulky phenyl groups, packing of PS chains is not efficient and hence it is
amorphous polymer. Its specific gravity (1.054) is also low.
ii. It has good optical properties like it is transparent polymer allowing high transmission of all wave
lengths. Moreover, its high refractive index (1.592) gives it a particularly high ‘brilliance’.
iii. Due to chain stiffening effect of benzene ring, PS is hard but brittle. It emits a characteristic metallic
sound when dropped.
iv. Being non-polar amorphous polymer, its softening temperature (82-1000C) is low. It cannot withstand
the temperature of boiling water.
v. As it is non-polar so it has low tendency for moisture absorption. Moreover, it has good electrical
insulation characteristics.
vi. It has reasonable chemical resistance but mediocre oil resistance.
Applications: Polystyrene is used for making: audio cassettes, containers for talcum powder, house-wares
(small jars & storage containers), bottle caps, combs and brush handles.
Q.No.5: a. Write a short note on Natural rubbers and to discuss vulcanization?
b. Write the preparation, properties & applications of buna-s, butyl rubber & Thiokol rubber
Natural Rubber: Rubbers also known as Elastomers, they are high polymers, which have elastic
properties in excess of 300%.
Natural rubbers consist of basic material latex, which is a dispersion of isoprene. During the treatment, these
isoprene molecules polymerize to form, long-coiled chains of cis-polyisoprene. Natural rubber is made from
the saps of a wide range of plants like Hevea brasillians and guayule.
Latex: is a milky white fluid that oozes out from the plant Hevea brasillians when a cut is made on the steam
of the plant.
The latex is diluted with water. Then acetic or formic acid is added [1kg of acid per 200kgs of latex] to
prepare coagulum. This is processed to give wither crepe rubber or smoked rubber.
Vulcanization:
Vulcanization discovered by Charles Goodyear in 1839.
It consists of heating the raw rubber at 100 – 1400C with sulphur. The combine chemically at the
double bonds of different rubber spring and provides cross-linking between the chains. This cross-linking
during vulcanization brings about a stiffening of the rubber by anchoring and consequently preventing
intermolecular movement of rubber springs. The amount of sulphur added determines the extent of stiffness of
vulcanized rubber. For example, ordinary rubber (say for battery case) may contain as much as 30% sulphur.
Advantages of vulcanization:
i. The tensile strength increase.
ii. Vulcanized rubber has excellent resilience.
iii. It has boarder useful temperature range (-40 to 1000C)
iv. It has better resistance to moisture, oxidation and abrasion.
v. It is resistance to organic solvents like CCl4, Benzene petrol etc.
vi. It has only slight thickness.
vii. It has low elasticity.
Polymer Science (Unit-III) 10 Prepared by B.SRINIVAS
11. Buna – S or STYRENE RUBBER:
Buna-S rubber is probably the most important type of synthetic rubber, which is produced by
copolymerization of butadiene (about 75% by weight) and styrene (25% by weight).
nCH2 = CH – CH = CH2 + n CH2 = CH –Ph -(-H2C -CH = CH –CH --CH2 –CH – Ph-)n-
1,3-butadiene (75%) Styrene(25%)
Properties: Styrene rubber resembles natural rubber in processing characteristics as well as quality of
finished products.
It possesses high abrasion-resistance, high load-bearing capacity and resilience. However, it gets readily
oxidized, especially in presence of traces of ozone present in the atmosphere. Moreover, it swells in oils and
solvents. It can be vulcanized in the same way as natural rubber either by sulphur or sulphur monochloride
(S2Cl2). However, It requires less sulphur, but more accelerators for vulcanization.
Uses: Mainly used for the manufacture of motor tyres. Other uses of these elastomers are floor tiles, shoe
soles, gaskets, foot-wear components, wire and cable insulations, carpet backing, adhesives, tank-linings, etc.
Butyl Rubber (GR-I or Polyisobutylene):
Preparation: Butyl rubber is prepared by the aluminum chloride initiated cationic co-polymerization of
isobutene with small amount (0.5 to 2.5%) of isoprene.
Properties: Butyl rubber has following characteristics:
a. Under normal conditions it is amorphous but it crystallizes on stretching.
b. It is quite resistant to oxidation due to low degree of unsaturation.
c. Due to very low unsaturation, it can be vulcanized but it cannot be hardened much.
d. It can be degraded by heat or light to sticky low-molecular weight products so stabilization is must.
e. Butyl rubber is soluble in benzene but has excellent resistance to polar solvents like alcohol, acetone.
f. Compared to natural rubber it possesses outstanding low permeability to air and other gases.
Applications: Butyl rubber used for
a. Insulation of high voltage wires and cables.
Polymer Science (Unit-III) 11 Prepared by B.SRINIVAS
12. b. Inner tubes of automobile tyres.
c. Conveyor belts for food and other materials.
d. Lining of tanks and Hoses.
Thiokol rubber:
This also called as polysulphide rubber (or Gr-P). It can be prepared by the condensation
polymerization of sodium polysulphide (Na2Sx) and ethylene dichloride.
It is used for the -
i. Manufacture of oils hoses, chemically resistant tubing and engine gaskets;
ii. Diaphragms and seals in contact with solvents and
iii. Printing rolls,
iv. Containers for transporting solvents and
v. Solid propellant fuels for rockets, etc.
Q.No. 6: a. Write a short note on conducting polymers & mention its applications?
b. Describe preparation, conduction properties & applications of Polyactylene & polyanilline
a. Conducting polymers: Those polymers which conduct electricity are Conducting polymers. The
conduction of polymers may be due to unsaturation or due to the presence of externally added ingredients in
them. The conducting polymers can classify in the following way.
Conducting polymers divided in to two types.
1. Intrinsic conducting polymers
2. Extrinsic conducting polymers
Intrinsic conducting polymers: These polymers are characterized by intensive conjugation of double bonds in
their structure i.e. the backbone of the polymer. Again intrinsic conducting polymers are two types.
a. Conducting polymers having conjugation
b. Doped conducting polymers
Conducting polymers having conjugation: Such polymers having conjugated double bonds in the backbone
possess their conductivity due to pi electrons. In pi bonding the overlapping of the orbital is lateral over the
entire backbone resulting in the formation of valence bands and conducting bands which were separated by a
significant Fermi energy gap. The electrical conductivity takes place only after thermal or photolytic
activation of the electrons, which give them sufficient energy to jump the gap and reach into conduction band.
Doped conducting polymers: The conducting polymers having pi electrons in their backbone can easily be
oxidized or reduced because they possess low ionization potential and high electron affinities. Hence their
conductance can be increased by introducing a positive charge or negative charge on polymer backbone by
Polymer Science (Unit-III) 12 Prepared by B.SRINIVAS
13. oxidation or reduction. This process is similar to semiconductor technology and is called doping. Doping is
again two types.
1. Creating a positive site on polymer backbone called p-doping
2. Creating a negative site on polymer backbone called n-doping
P - Doping: p-doping is done by oxidation of a conducting polymer like polyacetylene with a lewice acid or
iodine vapour. This type of doping also known as oxidative doping.
During oxidation process the removal of pi electrons from polymer backbone lead to the formation of
a delocalized radical ion called polaron having a hole in between valence band and conducting band.
The second oxidation of the polaron results in two positive charge carriers in each chain called bipolaron,
which are mobile because of delocalization. These delocalized charge carriers are responsible for conductance
when placed in electric field.
n-doping: n-doping is carried out by reduction process by the addition of an electron to polymer backbone
by using reducing agents like sodium naphthalide. Formation of polaron, bipolaron takes place in two steps,
followed by recombination of radicals, which yields two charge carriers on the polyacetylene chain
responsible for conduction.
The electron added to polyacetylene by reductive doping does not go into the conducting band but
goes into an intermediate electronic state within the band gap of radical anion (polaron).
Bipolaron contains electrons in the energy levels residing in the band gap.
The Bianion lowers its energy by segregating into two negative solitrons at the midgap energy levels.
The presence of holes in the band gap allows facile jumps of electrons from valence band into the conduction
band. This leads to the generation of conduction pathways. As a consequence the conductivity increases
significantly.
In general doping increases the surface conductivity of a polymer to a large extent.
Polyanilines exist in several oxidation states as far as electrical conductivities are concerned varying from 10-
11 S/cm to >105 S/cm only one form called emeraldine salt is electrically conducting. The flexible dark blue
Applications of conducting polymers:
a. In rechargeable batteries: These batteries are small in size, longer lasting and can produce current
density up to 50mA/cm2. Move over, these rechargeable batteries have ecological advantage as they
do not involve heavy metals so they do not appear to have any serious toxicological problems.
b. In analytical sensors: Conducting polymers are also used for making sensors for pH, O2, NOx, SO2,
NH3 and glucose.
c. For making Ion-exchangers: Membranes made up of them can show boundary layer effects with
selective permeability for ions, gases, etc.Hence,they are useful for ion-exchangers and controlled
release of drugs. Diffusion of the drug from the polymer matrix permits a continuous and controlled
Polymer Science (Unit-III) 13 Prepared by B.SRINIVAS
14. release. With this, regular injection or oral ingestion of the drug is no0 longer needed. This technique
has been used for the slow release of birth control drugs and it has potential to be used for cancer
chemotherapy.
d. In electro-chromic displays and optical filters: ICP’s can absorb visible light to give coloured
products so can useful for electro-chromic displays and optical filters. Thus, conducting polymers can
be used as electro-chromic materials.
e. In electronics: Photo structural lacquers based on ICP’s are useful for electron beam lithography,
LED’s and data storage. Emaraldine base form polyaniline is used as a resist for lithography. Its
solution in NMP (1-methyl-2-pyrrolidine) mixed with triphenylsulphonium hexafluroantimonate has
been used to spin coat thin films on quartz and silicon wafers. This blue film on exposure to UV
radiation of 240 nm turns green, characteristic of conducting state of polyaniline. Conducting lines as
small as 0.5 m can be obtained by using this technique.
b. 1. Poly acetylene: The conjugated polymer with simplest chemical structure is poly acetylene.
Polymerisation of acetylene over Ziegler Natta catalysts gives poly acetylene which in its used form with
increasing temperature gets transformed to more stable trans-form. This polymer is infusible, insoluble and
becomes brittle on exposure to air. The conductivity of poly acetylene is magnified by doping. Exposure of
the film to dry ammonia gives a polymer with conducvity of 103 Scm-1, controlled addition of P-doping agents
like AgF5, Br2, I2 or HClO4 could move to still higher conductivities.
Conducting mechanism in poly acetylene:
The semi conducting poly acetylene (CH2)n has a typical carbon – carbon back bone structure.
The localized electrons in ‘s’ bonds form the back bone of the polymer chain and dominate the medicinal
properties, while the electrons in the π bonds are delocalized along the chain and responsible for the electrical
and optical properties of a conjugated polymer.
The σ bonds form completely filled low lying energy bonds that have larger energy gas than the π bond
electrons.
Before passing current, the electrons can flow along the molecule and one or more electrons have to be
removed or inserted.
In presence of an electric field, the electrons constituting π –bonds can move along the molecular chain. The
conductivity of the polymeric material, containing many chains of polymers will be limited by the fact that the
electrons have to jump from one molecule to the next. Hence, the chains have to be packed in an ordered row.
Doping of poly acetylene: poly acetylene possesses alternate single and double bonds that give rise to mobile
–electrons when doped, i.e. become anisotropic metallic conductors. There are two types of doping, oxidation
or reduction.
1. oxidation with halogen- (P-doping)
2. Reduction with alkali metal – (n-doping)
2. Poly-aniline: Among the conducting polymers, poly-aniline posses unique properties.
Poly-aniline is conjugated polymer and is reactive. Poly-aniline is considered as an organic metal. Its specific
conductivity is 55 cm-1. Poly-aniline is transparent in thin layers. In conducting state it is green. It turns red
under reducing conditions and blue under oxidising or basic ones.
Poly-aniline is a stable conducting polymer. It has wide range of conductivity. It shows multi-colour electro-
chromism and chemical sensitivity.
It can be synthesised chemically or electro-chemically as a bulk powder or film.
Polymer Science (Unit-III) 14 Prepared by B.SRINIVAS
15. It is one of the oldest conductive polymers known. It was prepared by the anodic oxidation of aniline in
H2SO4. Its conductivity is due to conjugated p-bond system formed by the overlapping of carbon p-orbital and
alternating C-C bond lengths extending over large number of recurring monomer units. In poly-aniline pz
orbitals of nitrogen and carbon rings are also part of the conjugated system.
Conjugated double bonds permit the electron mobility throughout the molecule due to delocalised electrons.
In addition, it has a conjugated double bond structure, i.e. benzenoid ring between the quininoid imines and
the benzenoid amine structure.
Preparation of poly-aniline: poly-aniline is prepared by the redox polymerization of aniline in protonic and
aqueous solution in the presence of ammonium per di sulphate as oxidant. It can be regarded as conducting
polymer under certain stimulating conditions like UV light, heat or addition of a suitable dopant to the
polymer.
Doping of poly-aniline: it can be made conductive by p-type (oxidation) doping or n-type (reduction) doping
of polymer. In undoped state, it is a poor semi conductor. On doping with dopant para-hydroxy benzene
sulphonic acid, its conductivity is increased by a factor of 10 dm -1/cm or more and forms polaron/ bipolaron
structure. The conductivity σ of a conducting poly-aniline is related to number of charge carriers ‘n’ and their
mobility µ .
Therefore, σ = neµ
Properties of poly-aniline: Due to the presence of extended π –bond system of conjugated polymers, it is
highly susceptible to chemical and electrochemical oxidation or reduction. As a result, the electrical and
optical properties of the polymer are altered.
Electronically conducting polymers are extensively conjugated molecules and possess specially delocalised
band line structure.
Disadvantages:
1. Poly-aniline decomposes prior to melting. Hence, it is difficult to process.
2. It is insoluble in common solvents except strong acids and N-methyl prolidone.
3. It has poor mechanical properties.
Applications:
1. Poly-aniline is used for corrosion protection, sensors, smart windows, printed circuit boards,
conductive fabrics and conductive pipes for explosives.
Q.No. 7: Write a short note on Liquid crystal polymers
Liquid crystal polymers (LCP)
Liquid crystals are materials that behave in some ways like solid and in some ways like liquids. Stephanie
Kwolek, a chemist, working at Dupont, had made the first known polymer liquid crystal solution. Kwolek had
invented a new polymer based on the polyamide, named Kevlar.
The macromolecule with the above structure produces very strong fibers. When this polymer dissolved in
tetra-methyl urea (II) and calcium chloride, the polymer molecules behave strongly. The Kevlar molecular
which were long, straight, and stiff, lined up like logs floating down a river, because of the strange opalescent
look of the solution.
Polymer Science (Unit-III) 15 Prepared by B.SRINIVAS
16. This is unusual because normally molecules in a solution or a pure liquid are not arranged in any orderly
fashion. Molecules of solids materials are arranged in orderly fashion called ‘crystals’.
Since Kevlar solution is a liquid, but its molecules are orderly arranged, the solution is called a ‘liquid
crystals’. Liquid crystals can be classified in to 2 types.
1. Liquid crystalline in polymers may occur by dissolving a polymer in a solvent, which are called lypo-
tropic liquid crystal polymers. Eg. Kevlar.
2. Liquid crystalline in polymer may occur by heating a polymer above its glass transition temperature or
melting transition point, which are called thermo-tropic liquid crystal polymers. Eg. Vectra
Properties of liquid crystal polymers:
1. These polymers are capable of forming regions of highly ordered structure while in liquid phase. The
degree of order is somewhat less than that of a regular solid crystal.
2. The liquid crystal polymers have high mechanical strength at high temperatures.
3. These liquid crystal polymers possess extreme chemical resistance.
4. They possess inherent flame retardancy and good weather-ability.
5. They can be easily fabricated into a variety of forms.
6. LCP can be welded. The lines created by welding are the weak points in the resulting product.
7. LCP has high Z-axis co-efficient of thermal expansion.
8. LCP resist stress cracking the presence of most chemicals at elevated temperatures.
Applications of LCP:
LCP are some times called ‘super polymers’. Their wide range of exceptional properties and case of
processing make them design for many demanding applications.
1. LCP thermoplastic fibers possess exceptional strength and residity, suitable for industrial, electronic
and also space applications as well as high performance ropes and tennis rackets.
2. LCP finds extensive applications as coatings, composites, and additives.
3. The electrical motor components are made from LCP.
4. LCP finds its applications in electronic industry as LED’s and SMT components.
5. LCP ha
6. s an interesting application like information storage media.
Polymer Science (Unit-III) 16 Prepared by B.SRINIVAS
17. Q.No.8: Define fibers, classify & write preparation, properties & applications of polyester.
Fibers: Fibers are a class of materials that are continuous filaments or discrete elongated pieces. They are
highly crystalline form of polymers. They are biologically very important in both plants and animals. The
li8gments etc. that hold the tissue material are basically fibers. Fibers are used for making textiles, utilities,
ropes, strings, etc.
Fibers are classified in to two types depending on their origin.
1. Natural fibers
2. Synthetic fibers
Natural fibers: Natural fibers include those produced by plants, animals and geological material. They are
environment friendly and biodegradable. They are:
a. Vegetable fibers: They are basically cellulose material and include cotton, jute, etc. plant fibers found
application by even early man and are used for making textiles, ropes, mats, paper and bags etc.
dietary fiber is an essential component of our food and its deficiency could result in cancer.
b. Wood fibers: The strength of a plant is due to presence of wood fiber. Wood pulp is used in making
paper and wood fibers like jute are used for making bags.
c. Animal fibers: They are largely made of protein. Pure silk, wool, hair are animal fibers. We move our
li8mbs using fibers present in them. Spider silk is used for making special bullet proof jackets.
d. Mineral fibers: Asbestos is a typical example of mineral fiber. Mica and other minerals are also used
as fibers.
Synthetic fibers: this type fibers can be produced in large quantities and are cheaper than some of the
natural fibers like pure silk. Polyamide nylons, polyesters, PVC, phenol-formaldehyde resins,
polyethylene are often used for making textiles.
POLYESTER
This category of polymers has ester linkages in the main chain. It takes 18% of market share of
synthetic polymers.
Terylene is a polyester fiber made from ethylene glycol and terephthalicacid. Terephtalic acid required
for the manufacture of Terylene is produced by the catalytic atmospheric oxidation of p-xylene.
Polymer Science (Unit-III) 17 Prepared by B.SRINIVAS
18. Properties: This occurs as a colourless rigid substance. This is highly resistant to mineral and organic acids
but is less resistant to alkalis. This is hydrophobic in nature. This has high melting point due to presence of
aromatic ring.
Uses: It is mostly used for making synthetic fibers. It can be blended with wool, cotton for better use and
wrinkle resistance. Other application of polyethylene terephthalate film is in electrical insulation.
Q.No. 9: Write a short note on Fiber reinforced plastics.
Fiber reinforced plastics (FRP)
Fiber reinforced plastics are produced by reinforcing a plastic matrix with a high strength fiber materials such
as glass, Graphite, alumina, carbon, boron, beryllium and aromatic polyamide. Natural fibers such as sisal,
asbestos are also used for reinforcement. Depending on the desired properties of the final reinforced
composite, the nature of the fiber used is decided. Glass fiber is the most extensively used reinforced fiber
because of durability, acid proof, water proof, and fire proof nature of glass.
Glass is drawn into threads or fibers in the form of filaments fire than cotton or silk thread. Then the filaments
are woven in the form of mats. The fiber material is suitably bonded with plastics materials to be reinforced.
The common plastics resins used are polyester, epoxy, silicone, melamine, vinyl derivatives and polyamides.
The following are the various processing techniques adopted.
a. Matched metal die molding: This is the most efficient and economical method for mass production
of high strength parts. It is press moulding under a temperature of 235 – 260 F and 200 – 300 psi
pressure. The upper mould containing the resin and reinforcing fiber is pressed on the lower mould.
b. Injection Moulding: This method is for reinforced thermoplastics. A mix of short fiber and resin are
forced by a screw or plunger through a nozzle into the heated mould and allowed to curve.
c. Hand-lay-up: Mostly used thermoset plastic resins the reinforcing mat fiber is cut to fit in a mould
and saturated with resin by hand using a brush. Roller or spray gun. Layer built up gives the thickness
of the articles.
Polymer Science (Unit-III) 18 Prepared by B.SRINIVAS
19. d. Continuous lamination: reinforcing mats or fabrics are impregnated with resin, run through
laminating rolls between cellophane sheets to control the thickness and resin continent. They are then
cured in heating chamber.
e. Centrifugal casting: Chopped fibers and resin are placed inside a mandrel and uniformly distributed
as mandrel is rotated inside an oven.
f. Spray up: Short length of reinforcement and resin are projected by a specially designed spray gun so
that they are deposited simultaneously on the surface of the mould. Curing is done with a catalyst at
room temperature.
Applications of FRP: Fiber reinforced plastics find extensive use in space crafts, aeroplanes, boat nulls, acid
storage tanks, motor cars and building materials. Melamine FRP is used for insulation and making baskets.
Advantages of FRP: The fiber reinforced plastics have the following advantages.
a. Low efficient of thermal expansion
b. High dimensional stability
c. Low cost of production
d. Good tensile strength
e. Low dielectric constant
f. Non inflammable and non-corrode and chemical resistance.
Polymer Science (Unit-III) 19 Prepared by B.SRINIVAS