Tank sluice with tower head

•

16 likes•14,316 views

ila vamsi krishna

design Tank sluice with tower head design & drawing of irrigation structures jntu anantapur R13 AND R15 REGULATIONS

Engineering

Hydraulic failures .... 40% Seepage failures…….. 30% Structural failures .... 30% (1) Overtopping (2) Erosion of u/s slope by waves (3) Erosion of d/s slope by wind and rain (4) Erosion of d/s toe (5) Frost action (1) Overtopping = the design flood is under estimated. spillway capacity is not adequet spillway gates are not properly operated free board is not sufficient excessive settlement of the foundation and dam (2) Erosion of u/s slope by waves = The waves developed near the top water surface due to the winds, try to notch out the soil from the upstream face and may even, sometimes, cause the slip of the upstream slope. Upstream stone pitching or riprap should, therefore, be provided to avoid such failures. (3) Erosion of d/s slope by wind and rain = The rainwater flowing down the slope; may result in the formation of 'gullies' on the downstream slope thus damaging the dam which may generally lead to partial failure of the dam or in some cases it may cause complete failure of the dam. Erosion of d/s toe : = Toe erosion may occur due to two reasons : erosion due to tail water erosion due to cross currents that may come from spillway buckets. Frost action : = If the earth dam is located at a place where the temperature falls below the freezing point, frost may form in the pores of the soil in the earth dam. When there is heaving, the cracks may form in the soil. This may lead to dangerous seepage and consequent failure. Seepage failures : = Seepage failures may occur due to the following causes : (1) Piping through the foundation (2) Piping through the dam (3) Sloughing of d/s toe Structural failures := Structural failures in earth dams are generally shear failures leading to sliding of the tents or the foundations. (1) u/s and d/s slope failures due to construction pore pressures (2) u/s slope failure due to sudden drawdown (3) D/s slope failure due to steady seepage (4) Foundation slide due to spontaneous liquefaction (5) Failure due to earthquake (6) Failure by spreading (7) Slope protection failures (8) Failure due to damage caused by borrowing animals (9) Failure due to holes caused by leaching of water soluable salts Criteria for safe Design of Earth Dam : Section of an Earth Dam : The design of an earth dam essentially consists of determining such a cross section the dam which when constructed with the available materials will fulfill its required tion with adequate safety. Thus there are two aspects of the design of an earth dam.

Reservoir Planning

Sunny Agarwal

Reservoir Planning: Introduction; Investigations for reservoir planning; Selection of site for a reservoir; Zones of storage in a reservoir; Storage capacity and yield; Mass inflow curve and demand curve; Calculation of reservoir capacity for a specified yield from the mass inflow curve; Determination of safe yield from a reservoir of a given capacity; Sediment flow in streams; Life of reservoir; Reservoir sediment control; flood routing. Various types of Spillways and design.

Bituminous road construction

Anitha Jacob

SLUICE GATE

KOLEKAR AKSHAY VIVEKANAND

Presentation1Gaurav Bhati

What's hot

Unit 1 soil exploration Hand written notes

PRASANTHI PETLURU

Earth and rockfill dams

Civil Zone

Design of gravity dams

VikramKesharwani1

Canal Regulation & Cross Drainage Works

GAURAV. H .TANDON

Diversion Headworks

GAURAV. H .TANDON

Gravity Dam

Malla Reddy University

Lacey Regime Theory - Irrigation Engineering

Latif Hyder Wadho

Theory of structures II - STUDENT NOTE BOOK (Polytechnics Revision 2015)

SHAMJITH KM

Water resource engineering project list 2

shree samarth innovations

Diversion headwork

Bibhabasu Mohanty

Pile load test

Naman Kantesaria

Investigation for bridge construction

Madujith Sagara

Coffer dam and its type

Gaurang Kakadiya

Canal outlets

saibabu48

types of canals

number113

Measurement of discharge in channels & Design of lined canal

Jaswinder Singh

Canal

DKTE'S YASHWANTRAO CHAVAN POLYTECHNIC, ICHALKARANJI

Embankment lecture 3

Vidhi Khokhani

Reservoir Planning

Sunny Agarwal

Bituminous road construction

Anitha Jacob

What's hot (20)

Unit 1 soil exploration Hand written notes

Earth and rockfill dams

Design of gravity dams

Canal Regulation & Cross Drainage Works

Diversion Headworks

Gravity Dam

Lacey Regime Theory - Irrigation Engineering

Theory of structures II - STUDENT NOTE BOOK (Polytechnics Revision 2015)

Water resource engineering project list 2

Diversion headwork

Pile load test

Investigation for bridge construction

Coffer dam and its type

Canal outlets

types of canals

Measurement of discharge in channels & Design of lined canal

Canal

Embankment lecture 3

Reservoir Planning

Bituminous road construction

Viewers also liked

SLUICE GATE

KOLEKAR AKSHAY VIVEKANAND

Presentation1Gaurav Bhati

M.i tank

beerappa143

Earthen Dams

GAURAV. H .TANDON

Canal regulator

ila vamsi krishna

Hot selling wld 807 water leak detector

秋阳巫

Spillway

Naval Bandawar

Collection and Conveyance of Water

GAURAV. H .TANDON

Anonimous aplicaciones

xema24

Uncertainty modelling and limit state reliability of tunnel supports under se...

eSAT Journals

Abstract Underground openings and excavations are increasingly being used for civilian and strategic purposes all over the world. Recent earthquakes and resulting damage have brought into focus and raised the awareness for aseismic design and construction. In addition, underground tunnels, particularly, have distinct seismic behaviour due to their complete enclosure in soil or rock and their significant length. Therefore, seismic response of tunnel support systems warrant closer attention. The geological settings in which they are placed are often difficult to describe due to limited site investigation data and vast spatial variability. Therefore, the parameters which govern the design are many and their variabilities cannot be ignored. A solution to this issue is reliability based analysis and design. These real conditions of variability can only be addressed through a reliability based design. The problem addressed here is one of reliability-based analysis of the support system of an underground tunnel in soil. Issues like the description of the interaction between the tunnel lining and the surrounding medium, the type of limit state that would be appropriate, the nonavailability of a closed form performance function and the advantages of response surface method [RSM] are looked into. Both static and seismic environment with random variability in the material properties are studied here. Support seismic response is studied in terms of thrust, moment and shear forces in the lining. Interactive analysis using finite element method [FEM], combined with RSM and Hasofer-Lind reliability concept to assess the performance of the tunnel support, has proven useful under real field situations. Index Terms: Tunnel, Reliability, Random, Seismic

Shp components

RAJ BAIRWA

design of aqueductsanthosh2121

Sluice Gate Installation Guide - Watch Technologies

Watch Technologies

The following Installation Guide is designed to provide Watch Technologies’ customers with sufficient information to successfully install our gates as designed. Typically, our customers were provided both Shop Drawings and a 3-D CAD model of their gates prior to manufacture for both review and authorization to manufacture. If that was not the case please contact our office and secure these documents. These documents alone, however, may not provide the all the guidance everyone may require to place their gates into position and secure them for the long-term. This Guide will clearly define how Watch Technologies’ staff would install our gates.

[Credentials];[Notch JSC]AiiM Education

Orifice and mouthpieces

Thim Mengly(ម៉េងលី,孟李)

WARABANDI & MICROIRRIGATIONNISHANT SOURABH

Nrega Technical Aspects Of Execution Of Works By S.Anwar Hussain

Anwar Hussain

Highway

beerappa143

Relevant information and decision making

Aliza Racelis

Relevant+costKhalid Aziz

Viewers also liked (20)

SLUICE GATE

Presentation1

M.i tank

Earthen Dams

Canal regulator

Hot selling wld 807 water leak detector

Spillway

Collection and Conveyance of Water

Anonimous aplicaciones

Uncertainty modelling and limit state reliability of tunnel supports under se...

Shp components

design of aqueduct

Sluice Gate Installation Guide - Watch Technologies

[Credentials];[Notch JSC]

Orifice and mouthpieces

WARABANDI & MICROIRRIGATION

Nrega Technical Aspects Of Execution Of Works By S.Anwar Hussain

Highway

Relevant information and decision making

Relevant+cost

More from ila vamsi krishna

COMPOSITION AND MANUFACTURING OF BRICKS.pptx

ila vamsi krishna

CLASSIFICATION AND CHARACTERISTICS OF BRICK

ila vamsi krishna

COST EFFECTIVE GEOPOLYMER BRICKS -1

ila vamsi krishna

Geopolymer bricks are the new innovation in the field of brick industry. Geopolymer bricks contain fly ash as the source material and an alkaline activator for the activation of polymerization reaction.experimental work is supposed to be performed on geopolymer bricks with fly ash and GGBS as source materials and sodium hydroxide and sodium silicate as an activator. It reduces dead load on structures due to light weight (2.6 kg, dimension: 230 mm X 110 mm X 70 mm).

ANALYSIS AND DESIGN OF HIGH RISE BUILDING BY USING ETABS

ila vamsi krishna

Results of ETABS on HIGH RISE RESIDENTIAL BUILDINGS

ila vamsi krishna

Calculating quantity of cement in m20 grade concrete

ila vamsi krishna

Self compaction concrete

ila vamsi krishna

Planning and cost analysis of the commercial building

ila vamsi krishna

Planning and cost analysis of the commercial building

ila vamsi krishna

Experimental investigation of ohns surface property and process parameter on ...

ila vamsi krishna

Preliminary design of slab

ila vamsi krishna

Preliminary design of beam

ila vamsi krishna

Preliminary design of column

ila vamsi krishna

design of stair case

ila vamsi krishna

ANALYSIS AND DESIGN OF G+4 RESIDENTIAL BUILDING contents

ila vamsi krishna

residential buliding by stadd pro

ila vamsi krishna

COMPRESSIVE STRENGTH OF CONCRETE BY USING WASTE MATERIALS

Papercrete

plastic roads

Tunneling

More from ila vamsi krishna (20)

COMPOSITION AND MANUFACTURING OF BRICKS.pptx

CLASSIFICATION AND CHARACTERISTICS OF BRICK

COST EFFECTIVE GEOPOLYMER BRICKS -1

ANALYSIS AND DESIGN OF HIGH RISE BUILDING BY USING ETABS

Results of ETABS on HIGH RISE RESIDENTIAL BUILDINGS

Calculating quantity of cement in m20 grade concrete

Self compaction concrete

Planning and cost analysis of the commercial building

Experimental investigation of ohns surface property and process parameter on ...

Preliminary design of slab

Preliminary design of beam

Preliminary design of column

design of stair case

ANALYSIS AND DESIGN OF G+4 RESIDENTIAL BUILDING contents

residential buliding by stadd pro

COMPRESSIVE STRENGTH OF CONCRETE BY USING WASTE MATERIALS

Papercrete

plastic roads

Tunneling

Recently uploaded

Vaccine management system project report documentation..pdf

Kamal Acharya

Standard Reomte Control Interface - Neometrix

Neometrix_Engineering_Pvt_Ltd

About Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol. • Remote control: Parallel or serial interface. • Compatible with MAFI CCR system. • Compatible with IDM8000 CCR. • Compatible with Backplane mount serial communication. • Compatible with commercial and Defence aviation CCR system. • Remote control system for accessing CCR and allied system over serial or TCP. • Indigenized local Support/presence in India. • Easy in configuration using DIP switches. Technical Specifications Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol. Key Features Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol. • Remote control: Parallel or serial interface • Compatible with MAFI CCR system • Copatiable with IDM8000 CCR • Compatible with Backplane mount serial communication. • Compatible with commercial and Defence aviation CCR system. • Remote control system for accessing CCR and allied system over serial or TCP. • Indigenized local Support/presence in India. Application • Remote control: Parallel or serial interface. • Compatible with MAFI CCR system. • Compatible with IDM8000 CCR. • Compatible with Backplane mount serial communication. • Compatible with commercial and Defence aviation CCR system. • Remote control system for accessing CCR and allied system over serial or TCP. • Indigenized local Support/presence in India. • Easy in configuration using DIP switches.

Halogenation process of chemical process industries

MuhammadTufail242431

Top 10 Oil and Gas Projects in Saudi Arabia 2024.pdf

Teleport Manpower Consultant

Water Industry Process Automation and Control Monthly - May 2024.pdf

Water Industry Process Automation & Control

Welcome to WIPAC Monthly the magazine brought to you by the LinkedIn Group Water Industry Process Automation & Control. In this month's edition, along with this month's industry news to celebrate the 13 years since the group was created we have articles including A case study of the used of Advanced Process Control at the Wastewater Treatment works at Lleida in Spain A look back on an article on smart wastewater networks in order to see how the industry has measured up in the interim around the adoption of Digital Transformation in the Water Industry.

Sachpazis:Terzaghi Bearing Capacity Estimation in simple terms with Calculati...

Dr.Costas Sachpazis

Terzaghi's soil bearing capacity theory, developed by Karl Terzaghi, is a fundamental principle in geotechnical engineering used to determine the bearing capacity of shallow foundations. This theory provides a method to calculate the ultimate bearing capacity of soil, which is the maximum load per unit area that the soil can support without undergoing shear failure. The Calculation HTML Code included.

Democratizing Fuzzing at Scale by Abhishek Arya

abh.arya

Presented at NUS: Fuzzing and Software Security Summer School 2024 This keynote talks about the democratization of fuzzing at scale, highlighting the collaboration between open source communities, academia, and industry to advance the field of fuzzing. It delves into the history of fuzzing, the development of scalable fuzzing platforms, and the empowerment of community-driven research. The talk will further discuss recent advancements leveraging AI/ML and offer insights into the future evolution of the fuzzing landscape.

power quality voltage fluctuation UNIT - I.pptx

ViniHema

Nuclear Power Economics and Structuring 2024

Massimo Talia

CME397 Surface Engineering- Professional Elective

karthi keyan

Hybrid optimization of pumped hydro system and solar- Engr. Abdul-Azeez.pdf

fxintegritypublishin

Advancements in technology unveil a myriad of electrical and electronic breakthroughs geared towards efficiently harnessing limited resources to meet human energy demands. The optimization of hybrid solar PV panels and pumped hydro energy supply systems plays a pivotal role in utilizing natural resources effectively. This initiative not only benefits humanity but also fosters environmental sustainability. The study investigated the design optimization of these hybrid systems, focusing on understanding solar radiation patterns, identifying geographical influences on solar radiation, formulating a mathematical model for system optimization, and determining the optimal configuration of PV panels and pumped hydro storage. Through a comparative analysis approach and eight weeks of data collection, the study addressed key research questions related to solar radiation patterns and optimal system design. The findings highlighted regions with heightened solar radiation levels, showcasing substantial potential for power generation and emphasizing the system's efficiency. Optimizing system design significantly boosted power generation, promoted renewable energy utilization, and enhanced energy storage capacity. The study underscored the benefits of optimizing hybrid solar PV panels and pumped hydro energy supply systems for sustainable energy usage. Optimizing the design of solar PV panels and pumped hydro energy supply systems as examined across diverse climatic conditions in a developing country, not only enhances power generation but also improves the integration of renewable energy sources and boosts energy storage capacities, particularly beneficial for less economically prosperous regions. Additionally, the study provides valuable insights for advancing energy research in economically viable areas. Recommendations included conducting site-specific assessments, utilizing advanced modeling tools, implementing regular maintenance protocols, and enhancing communication among system components.

ethical hacking in wireless-hacking1.ppt

Jayaprasanna4

Cosmetic shop management system project report.pdf

Kamal Acharya

Buying new cosmetic products is difficult. It can even be scary for those who have sensitive skin and are prone to skin trouble. The information needed to alleviate this problem is on the back of each product, but it's thought to interpret those ingredient lists unless you have a background in chemistry. Instead of buying and hoping for the best, we can use data science to help us predict which products may be good fits for us. It includes various function programs to do the above mentioned tasks. Data file handling has been effectively used in the program. The automated cosmetic shop management system should deal with the automation of general workflow and administration process of the shop. The main processes of the system focus on customer's request where the system is able to search the most appropriate products and deliver it to the customers. It should help the employees to quickly identify the list of cosmetic product that have reached the minimum quantity and also keep a track of expired date for each cosmetic product. It should help the employees to find the rack number in which the product is placed.It is also Faster and more efficient way.

Gen AI Study Jams _ For the GDSC Leads in India.pdf

gdsczhcet

Railway Signalling Principles Edition 3.pdf

TeeVichai

Quality defects in TMT Bars, Possible causes and Potential Solutions.

PrashantGoswami42

Maintaining high-quality standards in the production of TMT bars is crucial for ensuring structural integrity in construction. Addressing common defects through careful monitoring, standardized processes, and advanced technology can significantly improve the quality of TMT bars. Continuous training and adherence to quality control measures will also play a pivotal role in minimizing these defects.

Final project report on grocery store management system..pdf

Kamal Acharya

In today’s fast-changing business environment, it’s extremely important to be able to respond to client needs in the most effective and timely manner. If your customers wish to see your business online and have instant access to your products or services. Online Grocery Store is an e-commerce website, which retails various grocery products. This project allows viewing various products available enables registered users to purchase desired products instantly using Paytm, UPI payment processor (Instant Pay) and also can place order by using Cash on Delivery (Pay Later) option. This project provides an easy access to Administrators and Managers to view orders placed using Pay Later and Instant Pay options. In order to develop an e-commerce website, a number of Technologies must be studied and understood. These include multi-tiered architecture, server and client-side scripting techniques, implementation technologies, programming language (such as PHP, HTML, CSS, JavaScript) and MySQL relational databases. This is a project with the objective to develop a basic website where a consumer is provided with a shopping cart website and also to know about the technologies used to develop such a website. This document will discuss each of the underlying technologies to create and implement an e- commerce website.

Industrial Training at Shahjalal Fertilizer Company Limited (SFCL)

MdTanvirMahtab2

WATER CRISIS and its solutions-pptx 1234

AafreenAbuthahir2

block diagram and signal flow graph representation

Divya Somashekar