Grade 11, Review topics for electricy test
•
0 likes•767 views
This document outlines the topics and format for a Grade 11 Electricity Half Test. It will cover defining and drawing series and parallel circuits, using Ohm's law and Kirchhoff's laws to calculate current, resistance, and voltage in complex circuits, properly connecting measurement devices, and identifying shorts. The test format includes true/false, multiple choice, drawing a circuit, and a complex circuit analysis question requiring calculating over 5 currents and voltages.
Report
Share
Report
Share
Recommended
Grade 11, U3 L3-Resistance-in-conductors
This document discusses electrical resistance in conducting wires and Ohm's Law. It explains that resistance depends on the material, length, and cross-sectional area of the conductor. Resistance increases with length or smaller cross-sectional area. Ohm's Law states that voltage is directly proportional to current, and resistance can be calculated as voltage divided by current. The document provides examples and practice problems to illustrate these concepts.
Grade 11, U3 L2-Electric Current
Electric current is defined as the amount of charge passing through a given point per unit time. It is measured in Amperes (A), where 1 A equals 1 Coulomb of charge passing by each second. Electric current in circuits behaves similarly to the flow of water in pipes and is measured using an ammeter connected in series. The direction of electron flow in circuits is opposite to the defined direction of conventional current. Kirchhoff's node law states that the total current entering a node equals the total current leaving the node. Shorting a load bypasses it using a jumper wire to allow current to take the path of least resistance.
Grade 11, U5 L6, P-Loss and Transformer
This document provides information about power loss during electrical transmission and the operation of transformers. It discusses how resistance causes power loss and how this loss can be calculated using current and resistance. Larger conductor cross-sectional areas and materials with lower resistivity are recommended to reduce power loss. Transformers are also introduced as a way to reduce power loss by stepping voltages up for transmission and down for use. The key functions and ratios involving voltage, current, and coil turns for transformers are explained. Practice questions are provided at the end from the textbook and workbook.
Grade 11,U3 L4-resistance in Series and Parallel CCT's
This document discusses resistance in series and parallel circuits. For a series circuit, the total resistance (RReq) is calculated by adding all individual resistances (R1 + R2 + R3 + ...). For a parallel circuit, the total resistance is calculated using the reciprocal of the sum of the reciprocals of the individual resistances (1/R1 + 1/R2 + 1/R3 + ...)-1. The document provides examples of calculating total resistance and includes practice questions related to resistance in series and parallel circuits.
Electrical resistance
1) Electricity is a form of energy that can be produced from other types of energy like chemical reactions or mechanical rotation. It has advantages like being clean, flexible, efficient, and allowing for easier transmission.
2) An electric circuit consists of a power source, load, switches, and other elements connected by wires. Resistors, rheostats, and resistance boxes in a circuit are made of materials like manganin and constantan.
3) Ohm's law states that the current through a conductor is directly proportional to the potential difference across it, provided the physical conditions stay the same. The resistance of a conductor depends on its length, cross-sectional area, and the material it is
Resistivity
Resistivity is a measure of a material's ability to resist electric current flow. It quantifies how strongly a material opposes current. The resistance of a material increases as its resistivity or length increases, and decreases as its area increases. While the resistivity of most conductors increases with temperature, the resistivity of some semiconductors like carbon and silicon decreases with rising temperature due to increased electron mobility.
Practical12
The document outlines experiments for a CBSE Class 12 Physics practical exam, including:
1. Determining the resistance of a wire and its specific resistance using a metre bridge.
2. Verifying the laws of series and parallel combinations of resistances using a metre bridge.
3. Comparing the EMF of two primary cells and determining the internal resistance of a primary cell using a potentiometer.
4. Determining the resistance of a galvanometer, converting it into an ammeter and voltmeter, and finding the refractive index of liquids and focal lengths of lenses and mirrors.
Ohms Law
Ohm's law defines the relationship between voltage, current, and resistance in a circuit. It states that current is directly proportional to voltage and inversely proportional to resistance. The amount of current, voltage, or resistance in a circuit can be calculated if two of the three values are known using the equation: I = V/R
Some key points about Ohm's law include:
- Voltage is measured in volts (V), current in amps (A), and resistance in ohms (Ω)
- Ohm's law can be rearranged to solve for any of the three circuit variables
- Examples are provided to demonstrate calculating unknown values given two known values
Recommended
Grade 11, U3 L3-Resistance-in-conductors
This document discusses electrical resistance in conducting wires and Ohm's Law. It explains that resistance depends on the material, length, and cross-sectional area of the conductor. Resistance increases with length or smaller cross-sectional area. Ohm's Law states that voltage is directly proportional to current, and resistance can be calculated as voltage divided by current. The document provides examples and practice problems to illustrate these concepts.
Grade 11, U3 L2-Electric Current
Electric current is defined as the amount of charge passing through a given point per unit time. It is measured in Amperes (A), where 1 A equals 1 Coulomb of charge passing by each second. Electric current in circuits behaves similarly to the flow of water in pipes and is measured using an ammeter connected in series. The direction of electron flow in circuits is opposite to the defined direction of conventional current. Kirchhoff's node law states that the total current entering a node equals the total current leaving the node. Shorting a load bypasses it using a jumper wire to allow current to take the path of least resistance.
Grade 11, U5 L6, P-Loss and Transformer
This document provides information about power loss during electrical transmission and the operation of transformers. It discusses how resistance causes power loss and how this loss can be calculated using current and resistance. Larger conductor cross-sectional areas and materials with lower resistivity are recommended to reduce power loss. Transformers are also introduced as a way to reduce power loss by stepping voltages up for transmission and down for use. The key functions and ratios involving voltage, current, and coil turns for transformers are explained. Practice questions are provided at the end from the textbook and workbook.
Grade 11,U3 L4-resistance in Series and Parallel CCT's
This document discusses resistance in series and parallel circuits. For a series circuit, the total resistance (RReq) is calculated by adding all individual resistances (R1 + R2 + R3 + ...). For a parallel circuit, the total resistance is calculated using the reciprocal of the sum of the reciprocals of the individual resistances (1/R1 + 1/R2 + 1/R3 + ...)-1. The document provides examples of calculating total resistance and includes practice questions related to resistance in series and parallel circuits.
Electrical resistance
1) Electricity is a form of energy that can be produced from other types of energy like chemical reactions or mechanical rotation. It has advantages like being clean, flexible, efficient, and allowing for easier transmission.
2) An electric circuit consists of a power source, load, switches, and other elements connected by wires. Resistors, rheostats, and resistance boxes in a circuit are made of materials like manganin and constantan.
3) Ohm's law states that the current through a conductor is directly proportional to the potential difference across it, provided the physical conditions stay the same. The resistance of a conductor depends on its length, cross-sectional area, and the material it is
Resistivity
Resistivity is a measure of a material's ability to resist electric current flow. It quantifies how strongly a material opposes current. The resistance of a material increases as its resistivity or length increases, and decreases as its area increases. While the resistivity of most conductors increases with temperature, the resistivity of some semiconductors like carbon and silicon decreases with rising temperature due to increased electron mobility.
Practical12
The document outlines experiments for a CBSE Class 12 Physics practical exam, including:
1. Determining the resistance of a wire and its specific resistance using a metre bridge.
2. Verifying the laws of series and parallel combinations of resistances using a metre bridge.
3. Comparing the EMF of two primary cells and determining the internal resistance of a primary cell using a potentiometer.
4. Determining the resistance of a galvanometer, converting it into an ammeter and voltmeter, and finding the refractive index of liquids and focal lengths of lenses and mirrors.
Ohms Law
Ohm's law defines the relationship between voltage, current, and resistance in a circuit. It states that current is directly proportional to voltage and inversely proportional to resistance. The amount of current, voltage, or resistance in a circuit can be calculated if two of the three values are known using the equation: I = V/R
Some key points about Ohm's law include:
- Voltage is measured in volts (V), current in amps (A), and resistance in ohms (Ω)
- Ohm's law can be rearranged to solve for any of the three circuit variables
- Examples are provided to demonstrate calculating unknown values given two known values
Internal Resistance, EMF and Oscilloscopes.ppt
The document discusses internal resistance, electromotive force (EMF), and using an oscilloscope to measure signals. It explains that batteries have internal resistance that causes voltage to drop as current increases. EMF is defined as the work needed to produce a potential difference without current flow. An example shows a starter motor drawing high current can cause headlights to dim due to the battery's internal resistance. Finally, it describes using an oscilloscope to measure the frequency and voltage of signals from a signal generator.
Ohm's law Presentation(gub abu bakar siddik )
Ohm's law states that the current through a conductor is directly proportional to the voltage applied. The document describes an experiment to demonstrate Ohm's law using a circuit with a fixed resistor. Voltage is varied using a DC power supply while current is measured with an ammeter. Measurements of voltage and current are recorded and their ratio is calculated and found to be approximately constant, demonstrating Ohm's law. A graph of voltage versus current shows a linear relationship, further confirming Ohm's law.
Electricity: Resistance
The document discusses electricity and resistance. It defines resistance as the ratio of voltage to current and explains that resistance depends on a material's resistivity, length, and cross-sectional area. It introduces Georg Ohm and Ohm's Law, which states that voltage and current are directly proportional. Resistors are circuit elements that produce voltage proportional to current according to Ohm's Law. Conductors contain movable electric charges like electrons that allow current to flow. Insulators contain fewer movable charges and resist current. The document contrasts alternating and direct current, noting that DC involves a constant unidirectional flow of charge.
omh's law
Ohm's law describes the relationship between voltage, current, and resistance in electrical circuits. It states that the current through a conductor is directly proportional to the voltage applied and inversely proportional to the resistance of the conductor. The mathematical equation for Ohm's law is I=V/R, where I is current, V is voltage, and R is resistance. Ohm's law applies to both metal conductors and circuit components specifically designed to obey it.
Chapter17: Direct current and Ohm's law
Electric current is the flow of electric charge. It is measured in amperes (A) which is equal to one coulomb of charge passing through an area in one second. Ohm's law states that the current through a conductor is directly proportional to the voltage applied across it. Resistance is a measure of how an object impedes the flow of current and is equal to the voltage divided by the current. Power is equal to the current times the voltage and describes the rate at which electrical energy is transferred by a circuit.
Ohm's law
The document discusses the basic components and relationships in electrical circuits. It explains that all circuits require a voltage source to provide energy to electrons, a conductor to carry the electrons, and a load or resistance where energy is extracted. It defines key electrical quantities like voltage, current, resistance, and Ohm's Law, which states that current is directly proportional to voltage and inversely proportional to resistance. The document also discusses how internal resistance affects the terminal voltage available from a source.
Grade 11, U5 Acad-Elect Mag
Electromagnetism can be created by the movement of electric charge. Hans Oersted discovered in 1819 that an electric current in a wire can produce a magnetic field around it. This led to the discovery of electromagnetism. The right hand rules describe the direction of magnetic fields produced by currents and currents produced by magnetic fields. Michael Faraday discovered in 1831 that a changing magnetic field can induce a current in a conductor. This is known as electromagnetic induction. Lenz's law states that the direction of the induced current is such that its magnetic field opposes the original change in magnetic field that caused it.
Presentation on electrical resistance
This document discusses electrical resistance. It defines resistance as the opposition to the flow of electrical current and explains that all devices have some resistance. It introduces the resistance equation of Resistance=Voltage/Current (R=V/I) and describes how to calculate voltage, current, or resistance when two values are known. It also describes different types of resistors like fixed resistors, variable resistors, and special resistors such as diodes, thermistors, and light dependent resistors (LDRs), explaining how their resistance changes with factors like temperature, light intensity, or direction of current. It concludes by mentioning Ohm's Law.
Electric field ohm s law_ etc.ppt
This document discusses several key concepts in electricity including:
1. Electric current is defined as the rate of flow of electric charge through a surface. The SI unit for current is the ampere.
2. Ohm's law states that the current through a conductor is directly proportional to the voltage applied. It is defined by the equation I = V/R where I is current, V is voltage, and R is resistance.
3. Resistance depends on the material properties, length, and cross-sectional area of the conductor. It can also vary with temperature according to its temperature coefficient.
3 ohm's law
The document discusses the relationships between current, voltage, and resistance according to Ohm's Law. It provides examples of applying Ohm's Law to calculate values in different circuit scenarios, such as calculating current given voltage and resistance. It also explains key concepts, including that resistance remains constant for a material, and that increases in voltage correspond to increases in current. The document aims to illustrate how Ohm's Law can be used to analyze electrical circuits.
Ohms law
Ohm's Law describes the relationship between voltage, current, and resistance in an electrical circuit. Voltage is the "push" of electricity and is measured in volts. Current is the flow of electricity and is measured in amps. Resistance opposes the flow of current and is measured in ohms. Ohm's Law states that current is directly proportional to voltage and inversely proportional to resistance. Using Ohm's Law, the voltage, current, or resistance in a circuit can be calculated if two of the three values are known. Resistors are used to decrease voltage in a circuit and are marked with color bands to indicate their resistance value. Circuits can be connected in series or parallel, and understanding circuit diagrams
Combination of Resistors — Series and Parallel | Physics
Electrical current is the flow of charged particles. The flow of charges will be constant in current electricity. Electric current flows from higher electric potential to lower electric potential. For the current to flow, it requires a circuit which is closed loop of a conducting material. Copy the link given below and paste it in new browser window to get more information on Combination of Resistors — Series and Parallel www.askiitians.com/iit-jee-electric-current/combination-of-resistors-series-and-parallel/
Physics II Circuit Notes
The document discusses resistors in series, parallel, and simple networks. It provides the cardinal rules for series and parallel circuits, including that the total resistance in a series circuit equals the sum of individual resistances, and the total current in a parallel circuit equals the sum of branch currents. Examples are given of calculating total resistance, current, and voltage drops in series and parallel circuits. Kirchhoff's laws of voltage and current are also summarized.
Resistance and their combinations
This document discusses resistors and resistor combinations in circuits. It covers resistor types including fixed and variable resistors. It also covers resistor color codes and examples of resistors in series and parallel combinations. The key topics are resistances and their combinations in series and parallel and how to calculate equivalent resistances for complex resistor networks using Ohm's law.
Resistors and resistance.ppt
The document discusses resistors, resistance, and circuits. It covers thermistors and how their resistance changes with temperature. Superconductors and how their resistance drops to zero below a critical temperature is explained. Series and parallel resistor circuits are analyzed. Methods for calculating total resistance, current, and power in circuits are provided along with example problems and their solutions.
3. calculate power in a basic electrical circuit
This document discusses calculating power in basic electrical circuits. It covers power being measured in watts as joules per second, power being dissipated when current flows through a resistor and is converted to heat or light. Formulas for power are provided using voltage, current and resistance. Examples are given of calculating power dissipated in series and parallel circuits. The effects of changing current, voltage and resistance on power are explored.
Grade 11, U5 L3-RHR#3
A current-carrying conductor placed in an external magnetic field experiences a force. This force is described by the Right-Hand Rule #3. Two parallel current-carrying conductors also experience a force of attraction or repulsion depending on whether the currents are in the same or opposite directions. The magnitude of the force between conductors can be calculated using the given equation. An example calculation is also provided to find the force on a conductor using the magnetic field strength, current, and length of the conductor in the field. Practice questions are listed at the end to test understanding of these concepts.
Electric circuits
1) This document discusses basic electric circuits including potential difference, voltage, current, resistance, Ohm's law, and different circuit configurations like series, parallel and compound circuits.
2) Key principles include that electric potential difference drives current flow, circuits require a closed path and energy source, and Ohm's law defines the relationship between voltage, current and resistance.
3) Circuit analysis involves applying concepts like voltage division in series circuits and current division in parallel circuits to calculate values like total resistance, current and voltage drops.
15 quantifying electricity 3 resistance
Resistance is a property that hinders the flow of electricity and converts it to another form of energy like heat. It is measured in ohms and depends on four factors - the type of material, its cross-sectional area, length, and temperature. Ohm's law states that the voltage between two points is directly proportional to the current flowing through, and resistance can be calculated by dividing the voltage by the current. An ohmmeter is used to measure resistance in a circuit.
Resistance by Mazhar Iqbal PIEAS University Islamabad Pakistan
This document discusses the concept of electrical resistance. It defines resistance as the ratio of potential difference (voltage) across a conductor to the current flowing through it. Resistance is measured in ohms and depends on several factors like the material, length, cross-sectional area, and temperature of the conductor. It also explains common units of resistance like the abohm and statohm. Ohm's law relating voltage, current and resistance is described. Finally, it discusses how resistance can be measured using an ohmmeter.
Electricity outline
The document outlines key concepts in electricity including definitions of neutrons, protons, electrons and static electricity. It discusses early scientists like JJ Thompson, Rutherford, and induction. Key topics covered include conductors, insulators, charging methods like friction and induction, current, voltage, batteries, resistors, and circuits. Measurement units for electrical concepts like coulombs for charge, amps for current, volts for voltage, and watts for power are also defined. Formulas for current, voltage, power, efficiency, and Ohm's law are listed.
How electricity works 03
Electricity is generated from mechanical or chemical energy sources like generators and batteries. It is transmitted through power stations and substations at high voltages before being stepped down by transformers for safe distribution and use. Electricity in homes is delivered through service panels at 120V to outlets and appliances, while electronics require DC power supplies to convert the alternating current to direct current usable by devices drawing less than a lethal 1 amp of current. Ohm's law defines the relationship between voltage, current, and resistance in electrical circuits.
More Related Content
What's hot
Internal Resistance, EMF and Oscilloscopes.ppt
The document discusses internal resistance, electromotive force (EMF), and using an oscilloscope to measure signals. It explains that batteries have internal resistance that causes voltage to drop as current increases. EMF is defined as the work needed to produce a potential difference without current flow. An example shows a starter motor drawing high current can cause headlights to dim due to the battery's internal resistance. Finally, it describes using an oscilloscope to measure the frequency and voltage of signals from a signal generator.
Ohm's law Presentation(gub abu bakar siddik )
Ohm's law states that the current through a conductor is directly proportional to the voltage applied. The document describes an experiment to demonstrate Ohm's law using a circuit with a fixed resistor. Voltage is varied using a DC power supply while current is measured with an ammeter. Measurements of voltage and current are recorded and their ratio is calculated and found to be approximately constant, demonstrating Ohm's law. A graph of voltage versus current shows a linear relationship, further confirming Ohm's law.
Electricity: Resistance
The document discusses electricity and resistance. It defines resistance as the ratio of voltage to current and explains that resistance depends on a material's resistivity, length, and cross-sectional area. It introduces Georg Ohm and Ohm's Law, which states that voltage and current are directly proportional. Resistors are circuit elements that produce voltage proportional to current according to Ohm's Law. Conductors contain movable electric charges like electrons that allow current to flow. Insulators contain fewer movable charges and resist current. The document contrasts alternating and direct current, noting that DC involves a constant unidirectional flow of charge.
omh's law
Ohm's law describes the relationship between voltage, current, and resistance in electrical circuits. It states that the current through a conductor is directly proportional to the voltage applied and inversely proportional to the resistance of the conductor. The mathematical equation for Ohm's law is I=V/R, where I is current, V is voltage, and R is resistance. Ohm's law applies to both metal conductors and circuit components specifically designed to obey it.
Chapter17: Direct current and Ohm's law
Electric current is the flow of electric charge. It is measured in amperes (A) which is equal to one coulomb of charge passing through an area in one second. Ohm's law states that the current through a conductor is directly proportional to the voltage applied across it. Resistance is a measure of how an object impedes the flow of current and is equal to the voltage divided by the current. Power is equal to the current times the voltage and describes the rate at which electrical energy is transferred by a circuit.
Ohm's law
The document discusses the basic components and relationships in electrical circuits. It explains that all circuits require a voltage source to provide energy to electrons, a conductor to carry the electrons, and a load or resistance where energy is extracted. It defines key electrical quantities like voltage, current, resistance, and Ohm's Law, which states that current is directly proportional to voltage and inversely proportional to resistance. The document also discusses how internal resistance affects the terminal voltage available from a source.
Grade 11, U5 Acad-Elect Mag
Electromagnetism can be created by the movement of electric charge. Hans Oersted discovered in 1819 that an electric current in a wire can produce a magnetic field around it. This led to the discovery of electromagnetism. The right hand rules describe the direction of magnetic fields produced by currents and currents produced by magnetic fields. Michael Faraday discovered in 1831 that a changing magnetic field can induce a current in a conductor. This is known as electromagnetic induction. Lenz's law states that the direction of the induced current is such that its magnetic field opposes the original change in magnetic field that caused it.
Presentation on electrical resistance
This document discusses electrical resistance. It defines resistance as the opposition to the flow of electrical current and explains that all devices have some resistance. It introduces the resistance equation of Resistance=Voltage/Current (R=V/I) and describes how to calculate voltage, current, or resistance when two values are known. It also describes different types of resistors like fixed resistors, variable resistors, and special resistors such as diodes, thermistors, and light dependent resistors (LDRs), explaining how their resistance changes with factors like temperature, light intensity, or direction of current. It concludes by mentioning Ohm's Law.
Electric field ohm s law_ etc.ppt
This document discusses several key concepts in electricity including:
1. Electric current is defined as the rate of flow of electric charge through a surface. The SI unit for current is the ampere.
2. Ohm's law states that the current through a conductor is directly proportional to the voltage applied. It is defined by the equation I = V/R where I is current, V is voltage, and R is resistance.
3. Resistance depends on the material properties, length, and cross-sectional area of the conductor. It can also vary with temperature according to its temperature coefficient.
3 ohm's law
The document discusses the relationships between current, voltage, and resistance according to Ohm's Law. It provides examples of applying Ohm's Law to calculate values in different circuit scenarios, such as calculating current given voltage and resistance. It also explains key concepts, including that resistance remains constant for a material, and that increases in voltage correspond to increases in current. The document aims to illustrate how Ohm's Law can be used to analyze electrical circuits.
Ohms law
Ohm's Law describes the relationship between voltage, current, and resistance in an electrical circuit. Voltage is the "push" of electricity and is measured in volts. Current is the flow of electricity and is measured in amps. Resistance opposes the flow of current and is measured in ohms. Ohm's Law states that current is directly proportional to voltage and inversely proportional to resistance. Using Ohm's Law, the voltage, current, or resistance in a circuit can be calculated if two of the three values are known. Resistors are used to decrease voltage in a circuit and are marked with color bands to indicate their resistance value. Circuits can be connected in series or parallel, and understanding circuit diagrams
Combination of Resistors — Series and Parallel | Physics
Electrical current is the flow of charged particles. The flow of charges will be constant in current electricity. Electric current flows from higher electric potential to lower electric potential. For the current to flow, it requires a circuit which is closed loop of a conducting material. Copy the link given below and paste it in new browser window to get more information on Combination of Resistors — Series and Parallel www.askiitians.com/iit-jee-electric-current/combination-of-resistors-series-and-parallel/
Physics II Circuit Notes
The document discusses resistors in series, parallel, and simple networks. It provides the cardinal rules for series and parallel circuits, including that the total resistance in a series circuit equals the sum of individual resistances, and the total current in a parallel circuit equals the sum of branch currents. Examples are given of calculating total resistance, current, and voltage drops in series and parallel circuits. Kirchhoff's laws of voltage and current are also summarized.
Resistance and their combinations
This document discusses resistors and resistor combinations in circuits. It covers resistor types including fixed and variable resistors. It also covers resistor color codes and examples of resistors in series and parallel combinations. The key topics are resistances and their combinations in series and parallel and how to calculate equivalent resistances for complex resistor networks using Ohm's law.
Resistors and resistance.ppt
The document discusses resistors, resistance, and circuits. It covers thermistors and how their resistance changes with temperature. Superconductors and how their resistance drops to zero below a critical temperature is explained. Series and parallel resistor circuits are analyzed. Methods for calculating total resistance, current, and power in circuits are provided along with example problems and their solutions.
3. calculate power in a basic electrical circuit
This document discusses calculating power in basic electrical circuits. It covers power being measured in watts as joules per second, power being dissipated when current flows through a resistor and is converted to heat or light. Formulas for power are provided using voltage, current and resistance. Examples are given of calculating power dissipated in series and parallel circuits. The effects of changing current, voltage and resistance on power are explored.
Grade 11, U5 L3-RHR#3
A current-carrying conductor placed in an external magnetic field experiences a force. This force is described by the Right-Hand Rule #3. Two parallel current-carrying conductors also experience a force of attraction or repulsion depending on whether the currents are in the same or opposite directions. The magnitude of the force between conductors can be calculated using the given equation. An example calculation is also provided to find the force on a conductor using the magnetic field strength, current, and length of the conductor in the field. Practice questions are listed at the end to test understanding of these concepts.
Electric circuits
1) This document discusses basic electric circuits including potential difference, voltage, current, resistance, Ohm's law, and different circuit configurations like series, parallel and compound circuits.
2) Key principles include that electric potential difference drives current flow, circuits require a closed path and energy source, and Ohm's law defines the relationship between voltage, current and resistance.
3) Circuit analysis involves applying concepts like voltage division in series circuits and current division in parallel circuits to calculate values like total resistance, current and voltage drops.
15 quantifying electricity 3 resistance
Resistance is a property that hinders the flow of electricity and converts it to another form of energy like heat. It is measured in ohms and depends on four factors - the type of material, its cross-sectional area, length, and temperature. Ohm's law states that the voltage between two points is directly proportional to the current flowing through, and resistance can be calculated by dividing the voltage by the current. An ohmmeter is used to measure resistance in a circuit.
Resistance by Mazhar Iqbal PIEAS University Islamabad Pakistan
This document discusses the concept of electrical resistance. It defines resistance as the ratio of potential difference (voltage) across a conductor to the current flowing through it. Resistance is measured in ohms and depends on several factors like the material, length, cross-sectional area, and temperature of the conductor. It also explains common units of resistance like the abohm and statohm. Ohm's law relating voltage, current and resistance is described. Finally, it discusses how resistance can be measured using an ohmmeter.
What's hot (20)
Combination of Resistors — Series and Parallel | Physics
Combination of Resistors — Series and Parallel | Physics
Resistance by Mazhar Iqbal PIEAS University Islamabad Pakistan
Resistance by Mazhar Iqbal PIEAS University Islamabad Pakistan
Viewers also liked
Electricity outline
The document outlines key concepts in electricity including definitions of neutrons, protons, electrons and static electricity. It discusses early scientists like JJ Thompson, Rutherford, and induction. Key topics covered include conductors, insulators, charging methods like friction and induction, current, voltage, batteries, resistors, and circuits. Measurement units for electrical concepts like coulombs for charge, amps for current, volts for voltage, and watts for power are also defined. Formulas for current, voltage, power, efficiency, and Ohm's law are listed.
How electricity works 03
Electricity is generated from mechanical or chemical energy sources like generators and batteries. It is transmitted through power stations and substations at high voltages before being stepped down by transformers for safe distribution and use. Electricity in homes is delivered through service panels at 120V to outlets and appliances, while electronics require DC power supplies to convert the alternating current to direct current usable by devices drawing less than a lethal 1 amp of current. Ohm's law defines the relationship between voltage, current, and resistance in electrical circuits.
How does electricity works
Matter is anything that occupies space and has weight. It may consist of elements or a single element. An element cannot be split into simpler substances, such as copper, oxygen, carbon, and gold. Atoms are the smallest particles of an element and are made up of protons, neutrons, and electrons. Protons are positively charged, electrons are negatively charged, and neutrons have no charge. Electricity is a branch of science concerned with charges. It can be drawn from devices like dry cells, solar cells, acid batteries, and dynamos. Conductors allow electricity to pass through easily, while insulators do not. Common terms in electricity include static electricity, current electricity, electric current, electric circuit, amp
Vacuum suction powerpoint
Vacuum suction uses suction cups to lift the skin and stimulate the lymphatic and circulatory systems. It can be used on any part of the body with sufficient fat and is often applied as a course of treatments to improve areas like cellulite. The machine consists of a pump, cups, tubing and controls. Treatment methods include gliding individual cups or using multiple pulsating cups. Precautions must be taken to prevent bruising, such as gradually increasing suction and releasing pressure before removing cups.
Microcurrent treatment
The document discusses micro-current treatment for skin. Micro-current uses low-intensity pulses of electric current to improve skin condition. It works by stimulating cell metabolism, improving muscle tone, and increasing collagen and elastin production. For best results, 12 treatments over 6 weeks are recommended, with photos before and after to demonstrate the benefits of the treatment.
High frequency Treatment
This document provides information on high frequency treatments, which use an alternating current over 100,000 cycles per second to heal, stimulate, or sanitize the skin. It describes direct high frequency, where the electrode is placed on the skin, and indirect high frequency (Viennese massage), where the client holds the electrode and the therapist massages the skin. Both methods increase circulation, speed cell metabolism, and have antibacterial effects. Precautions for safe application include removing jewelry, keeping the electrode in contact with the skin, and monitoring the client's comfort.
Vacuum suction powerpoint
The vacuum suction facial treatment uses a machine with cups to lift the skin and stimulate lymphatic and blood circulation. It works by applying suction through cups moved over the face to drain waste and improve skin condition. Precautions must be taken when applying the treatment, such as checking suction levels and releasing pressure before removing cups, to avoid bruising. The treatment benefits the lymphatic, circulatory, nervous, muscular and skin systems by improving drainage, blood flow, relaxation and cell metabolism.
Galvanic body treatment powerpoint
Galvanic body treatments use electrical currents to soften stubborn fat and disperse fluid retention. A galvanic machine delivers a smooth direct current through electrodes attached to gel pads on the skin. The current carries active ingredients from the gel into the skin to stimulate tissue fluid movement and improve the appearance of cellulite. Precautions must be taken to prevent burns, and aftercare focuses on hydration and lifestyle factors to maintain results.
Infra red radiations
This document provides an overview of infra red radiations (IRR) and their use in physiotherapy. It discusses topics such as the introduction and classification of IRR, their production and physical effects including heat production and absorption. Physiological effects of IRR like vasodilation and nerve stimulation are explained. The document also outlines indications and contraindications for IRR use as well as dangers and techniques for their application.
Galvanic Facial Treatment
Galvanic facials use a direct electric current to introduce solutions into the skin. A galvanic machine converts mains power into a smooth direct current up to 100 volts. Treatments include desincrustation, which cleanses skin, and iontophoresis, which introduces water-soluble ingredients. The polarity and solutions used determine the effects on the skin. Precautions must be taken to ensure client safety when applying the current.
Faradic Facial Treatment
This document provides information about faradic facial treatments. It explains that faradic current uses electrical pulses to stimulate facial muscles and cause contraction, tightening and toning. Regular treatments over 4-6 weeks are needed, along with home care. The treatment works by directly stimulating motor nerves, bypassing the brain, to contract muscles. Sensations include tingling and muscle contractions. Precautions for the treatment are also outlined.
Introducing Electricity
This document introduces electricity and electric circuits. It discusses:
1) The sources of electricity as main electricity from power stations and electric cells for portable devices.
2) The components of an electric circuit including connecting wires, bulbs, switches, and cells.
3) How circuits can be arranged in series or parallel and the differences between complete and incomplete circuits.
Viewers also liked (12)
Similar to Grade 11, Review topics for electricy test
CSE-I-BASIC ELECTRICALS ENGG. L1.pdf
This document outlines the syllabus for a Basic Electrical Engineering course. It includes 5 modules that cover topics such as DC circuits using Ohm's law, electromagnetism, DC machines, single and three phase AC circuits, transformers, and induction motors. The course objectives are to impart basic electrical knowledge, develop circuit analysis skills, highlight various electrical devices, and improve teamwork abilities. Kirchhoff's laws and their applications to circuit analysis are also explained.
CSE-I-BASIC ELECTRICALS ENGG. L1_2.pdf
This document outlines the syllabus for a Basic Electrical Engineering course. It includes 5 modules that cover topics such as DC circuits using Ohm's law and Kirchhoff's laws, electromagnetism, DC machines, measuring instruments, single-phase AC circuits, domestic wiring, three-phase circuits, synchronous generators, transformers, and induction motors. The objectives are to impart basic electrical knowledge, develop circuit analysis skills, highlight applications of generators, motors, and transformers, and emphasize safety. References and a detailed module-by-module breakdown are provided.
4th sem new
This document provides details of the modified course curriculum for the 4th semester BTech program in Electrical Engineering. It includes 10 courses with a total credit of 28. Some of the key courses include Electrical Machines-I, Power Systems I, Digital Electronics, Circuit Theory, and Microprocessors & Microcontrollers. For each course, the document provides information on course code, credit hours, prerequisites, topics to be covered, reference books, and course outcomes. It also provides the course structure for the Electrical Machines-I course including detailed topics in each part.
sscje.pdf
This document outlines the topics covered in an electrical engineering exam, including:
1) Circuit concepts such as resistance, inductance, capacitance, current, voltage, power, energy, and Kirchhoff's laws.
2) Magnetic circuit concepts like flux, mmf, reluctance, and properties of different magnetic materials.
3) AC fundamentals including instantaneous, peak, RMS values of waves and representation of sinusoidal waveforms.
4) Electrical machines including transformers, DC machines, 3-phase induction motors, and synchronous machines.
Lab 5 BASIC CIRCUITS( Resistors, Voltage,and Current with.docx
Lab 5: BASIC CIRCUITS
( Resistors, Voltage,
and Current with MATLAB adapted from P-178 DC Circuit Labs )
Introduction
:
Electric circuits can be defined as closed or continuous paths in which electric currents are confined and around which electric currents can be caused to flow. Electrical circuits are an essential part of daily living, and may be found in heavy and light industry, commercial installations and operations, and residential applications. Modern life and its many conveniences seem inconceivable without the use of electric circuits.
The total resistance of a circuit is the sum of the individual resistances of the power source, the wiring, and the load. The load resistance is generally much higher than either the resistance of the power source or the wiring. The resistances of the wiring are usually neglected in classroom laboratory experiments. Very rarely is circuit wiring significant in experimental work. In these cases we consider the loads resistances to be the only resistance. Wiring resistance may be considerable in the case of transmission cables, as well as telephone lines, which are many miles long, and we have a lab which investigates and calculates the resistance in such cables and the lost power and energy due to these lengths.
If an arbitrary load of relatively low resistance were connected to an existing power supply or voltage source, an excessive current might flow to the load, causing burn up or other malfunctions with the load and wiring.
The current can be reduced
by reducing the source voltage, but this is not always feasible and is frequently impossible. The resistances of the voltage source or the load could be increased, but these are usually built right into the source or load. Resistances of connecting wires are so low that miles would be needed to increase the circuit resistance by more than a few dozen ohms. A selection of materials for connecting wires might be useful, but a better method would be to creation of a device that is specifically a resistor that can be included with the circuit to give the net or total resistance needed to provide the desired current for the voltage source involved.
In any DC circuit, the total current is equal to the power source voltage divided by the total or equivalent resistance. For a Series Circuit, this is the only current. This means that if the current in some portion of the circuit is known, the total current and the current through every part of the circuit is known. The sum of the voltage drops across the resistors in series is equal to the power supply voltage.
In Parallel Circuits, the total current from the power source divides into different paths as in approaches the parallel branches. The voltage drop across parallel branches is the same for all the branches. If the voltage drop for one branch is known, the voltage drop for all the parallel branches is known.
The sum of the currents in the various branches is equal to the current from the po.
75. Deputy Engineer Electrical.pdf
The document provides a detailed syllabus for the post of Deputy Engineer (Electrical) in Kerala Co-operative Milk Marketing Federation Limited/ and Assistant Engineer (Electrical) KSEB. The 10-part syllabus covers topics including electric circuits, magnetic circuits, electrical machines, digital electronics, power systems, control systems, power electronics, operational amplifiers, measurements and instrumentation, signals and systems, transducers, batteries, electrical wiring and more. Candidates should prepare from all topics listed as well as others prescribed for the educational qualification; the exam questions may come from any part of the syllabus.
Experiment 3.pptx
The document provides information about a lab experiment on determining the power factor of a series RL circuit. It includes the objective, apparatus required, theory, circuit diagram, calculations, observations, learning outcomes, assessment pattern and references. The objective is to demonstrate a series RL circuit and determine the power factor. The required apparatus are an AC supply, variac, wattmeter, ammeter, voltmeter, variable resistive and inductive loads. Calculations involve determining power factor using equations for power, voltage, current and phase angle. Students will learn to make series connections and measure circuit parameters to calculate impedance and power factor.
Basic-ele-lab-syllabus
This document outlines the course details and experiments for a basic electrical engineering laboratory course. The course introduces common electrical components like resistors, capacitors, inductors, and machines. It includes 8 experiments that verify concepts like Kirchhoff's laws, measure properties of lamps and transformers, and characterize induction motors. Students will also learn about safety, making electrical connections, using measuring instruments, and controlling lamps with switches. The goal is for students to gain exposure to electrical components and understand basic machine operation.
60 -167-22 Asst. Prof Electrical Electronics.pdf
The document provides a detailed syllabus for the post of Assistant Professor in Electrical and Electronics Engineering. It is divided into 11 modules covering topics such as electric circuits, field theory, signals and systems, electrical machines, power systems, electrical system design, control systems, measurements and instrumentation, analog and digital electronics, power electronics, and microprocessors and computer systems. The syllabus is intended to test candidates on these core topics as well as other topics prescribed for the educational qualification of the position. Exam questions can come from any part of the syllabus, and not all specified topics may appear on the question paper.
Ies electrical engineering syllabus
This document provides an overview of the topics covered in the Electrical Engineering paper examinations, which include:
1. Theoretical concepts such as electric and magnetic fields, Maxwell's equations, and transmission lines.
2. Electrical materials like conductors, semiconductors, insulators, and magnetic materials.
3. Electrical circuits including circuit elements, network analysis techniques, and transient and steady-state responses.
Tti presentation_basic electricity level 1
This document provides an overview of the Basic Electricity Level I training course. The course objectives are to understand how electricity occurs, learn about universal magnitudes like voltage and current, broaden knowledge of magnetism, and learn Ohm's laws and electrical circuit components. Key topics covered include the composition of matter, electrical magnitudes and their units, direct and alternating current, resistance, series and parallel circuits, magnetism, batteries, alternators, starters, and troubleshooting faults. The course aims to familiarize students with electrical concepts and components through exercises and hands-on learning over the duration of two days.
Syllabus
This document outlines the objectives and outcomes of a course on electric circuits. The course aims to teach students about DC and AC circuit analysis, network theorems, resonance circuits, and three-phase circuits. It is divided into five units covering topics such as Ohm's law, Kirchhoff's laws, AC circuits, network theorems, transient response, and three-phase systems. The overall goal is for students to learn how to analyze different types of circuits and apply various methods of circuit analysis.
Slide about current voltage current and ampere
The document provides information about the Electrical Elements and Circuits course offered by Mirpur University of Science and Technology. It includes the course description, objectives, schedule, textbooks, and grading policy. The course covers topics such as passive elements, Kirchhoff's laws, circuit analysis methods, first and second order circuits, and alternating current fundamentals. The objectives are to introduce basic electrical engineering concepts and analyze linear electric circuits using various theorems and methods. The course runs for 48 lectures and is evaluated through assignments, exams, quizzes and lab work.
Basic electrical engineering syllabus(pokhara university)
This document outlines the syllabus for a Basic Electrical Engineering course, including course objectives, chapter contents, textbooks, and laboratory work. The course objectives are to analyze electric circuits, work on electrical projects, and operate electrical devices. The syllabus covers topics such as DC circuit analysis, single-phase and poly-phase AC circuits, electric machines, and transformers. Laboratory work includes verifying circuit laws and theorems, measuring transformer characteristics, and experiments on DC motors and generators.
Lecture02.pdf
This document discusses mathematical modeling of mechatronic systems. It describes how systems can be modeled using basic building blocks with defined input-output relationships. Electrical systems use resistors, capacitors, and inductors as basic blocks. Their characteristics are defined by equations relating potential difference and current. More complex systems can be modeled by combining blocks according to Kirchhoff's laws. Examples show how motors and other electromechanical systems can be mathematically modeled. The document also discusses linearity and how real-world non-linear components can be approximated with linear models.
3 sem ecsyll
This document provides information on the course "Digital System Design" including its objectives, modules, and outcomes. The key points are:
- The course covers topics like combinational logic design using K-maps and Quine McClusky, design of decoders, multiplexers, adders, and sequential circuits using latches and flip-flops.
- The modules include combinational logic analysis, design of combinational components, flip-flops and applications, sequential circuit design using Mealy and Moore models, and applications of digital circuits.
- The course aims to enable students to design various digital components, analyze sequential circuits, and appreciate applications of digital systems. Upon completion, students will be able to
Unit 1
This document provides an overview of the course 20EEG01 - BASIC ELECTRICAL AND ELECTRONICS ENGINEERING. The course aims to provide students with basic principles of electric circuits, electronic devices, electrical wiring, and AC/DC machines. Key topics covered include Ohm's law, Kirchhoff's laws, electric circuits, AC circuits, electrical machines, semiconductor devices, current controlled devices, and common circuit theory terms. The course outcomes are for students to understand basic concepts, domestic wiring, apply concepts to industrial applications, and analyze characteristics of electronic devices and circuits.
Basic Electrical Engineering
Basic Electrical Engineering - Questions (Review Questions) Refer this questions for all engineering branches .....
Similar to Grade 11, Review topics for electricy test (20)
Lab 5 BASIC CIRCUITS( Resistors, Voltage,and Current with.docx
Lab 5 BASIC CIRCUITS( Resistors, Voltage,and Current with.docx
Basic electrical engineering syllabus(pokhara university)
Basic electrical engineering syllabus(pokhara university)
More from gruszecki1
Topics for math test 2018
This document outlines the topics that will be covered on a math test for an academic physics course. It lists various grade 10 math concepts that students are expected to understand, such as the Pythagorean theorem, trigonometric ratios, solving linear and quadratic equations, graphing, slopes, and angles. The test will count towards students' term marks, so mastery of these prerequisite math skills is necessary to succeed in the grade 11 physics course. Students are advised to study by doing practice problems and reviewing old tests and textbook sections.
Grad12, U3-L2A-HorizPM-R
Horizontal projectile motion involves motion in two dimensions: up-down and horizontal. This document focuses on horizontal projectile motion, where the initial velocity only has a horizontal component. It examines how the horizontal velocity does not affect the rate of falling, but must be considered along with vertical motion to determine the total velocity and range of the projectile. The range of a projectile is calculated using the formula R = (2h/g)1/2v1, where h is the initial height, g is the acceleration due to gravity, and v1 is the initial horizontal velocity.
Grade9, L11-U3Habitat loss and fragmentation
Farmland, settlements and highways have replaced much of Ontario's deciduous forest. Habitat loss and fragmentation are threats, with loss most extreme in conversion to farmland and urban development. This divides ecosystems and exposes more habitat to pollution. To protect sustainability, conservation aims to maintain large, connected areas with low external influences. Threats also impact aquatic ecosystems through activities like shoreline development, dredging, sedimentation and wetland drainage.
Grade 9, U3-L10 pesticides and biomagnification
This document discusses pesticides and their environmental impacts. It describes how monocultures create ideal conditions for pest populations to thrive. Pesticides are commonly used to control pests, but they can harm non-target species and accumulate in organisms through bioaccumulation and biomagnification. Long-term pesticide use can also lead to pest resistance. The document advocates for alternative pest control methods like those used in organic farming to reduce pesticide dependence.
Grade 9-U3-L9-Invasive species
This document discusses invasive species, which are introduced species that spread rapidly and negatively impact the environment. It provides examples of invasive species in Canada like zebra mussels, European earwigs, and carp. Introduced species often lack natural predators and can outcompete native species, allowing their populations to grow unchecked. This can significantly damage ecosystems and cost the economy billions. The document outlines different methods to control invasive species populations, including pesticides, physical removal, and biological controls like introducing predators. However, prevention of accidental introductions is the most effective approach.
Grade 9,U3-L7 population ecology
The document discusses factors that affect population size and growth rates, including births and deaths, as well as immigration and emigration. It notes that population change equals births minus deaths plus immigration minus emigration. Density-dependent factors like competition for resources and disease can control populations. Density-independent factors like environmental conditions also impact populations. An example calculates the population change for a town based on births, deaths, immigration, and emigration to show that the population increased.
Grade9,U3-L6 Ecological Succession
Ecological succession describes how communities of plants and animals change over time following a disturbance of an area. It can be primary succession, which occurs in areas without previous life like after a volcanic eruption, or secondary succession, which follows a disruption but not destruction of a community like after a forest fire. Succession proceeds as hardier species first colonize an area, gradually changing the environment to allow less hardy species to establish themselves until a stable community forms, though it may take a hundred years to fully recover from severe disturbances. Aquatic and coastal ecosystems like bogs and sand dunes also undergo successional changes as vegetation grows and transforms the landscape over long periods.
Grade9, U3-L5 biotic and abiotic factors
This document discusses biotic and abiotic factors that influence ecosystems and populations. Abiotic factors like temperature, light, water, and soil determine where species can survive based on their tolerance ranges. Within tolerance ranges, optimal conditions allow populations to flourish while stress near limits can reduce health. Biotic factors like competition, predation, and mutualism also influence species success. As populations increase in size, resource demands increase until the ecosystem reaches its carrying capacity, or maximum sustainable population.
Grade 9, U3-L4 Cycles
The document discusses several biogeochemical cycles that move essential elements through ecosystems. It explains that the water cycle moves water through evaporation and precipitation, the carbon cycle exchanges carbon between the atmosphere and organisms through photosynthesis and respiration, and most carbon is stored long-term in deposits like fossil fuels. The nitrogen cycle converts nitrogen from the atmosphere into usable forms through nitrogen fixation by bacteria and returns it through denitrification. These cycles continuously circulate critical nutrients and are essential to sustaining life.
Grade 9, U3-L3 Food Chains and Food Webs
This document discusses ecological niches, food webs, and ecological pyramids. It defines key concepts like producers, consumers, herbivores, carnivores, omnivores, and describes trophic levels. Food chains are simplified representations of feeding relationships, while food webs show complex and interconnected feeding relationships in an ecosystem. Ecological pyramids illustrate the transfer of energy and biomass between trophic levels, with higher levels containing less energy and fewer individuals than lower levels due to energy loss at each transfer.
Grade9, U3-L2, Energy flow in ecosystems
All organisms require energy, which primarily comes from sunlight through photosynthesis. During photosynthesis, producers like plants use sunlight to convert carbon dioxide and water into oxygen and energy-rich sugars. Producers and consumers then undergo cellular respiration, using the sugars and oxygen to produce energy, carbon dioxide, and water. This cycle of photosynthesis and cellular respiration allows energy from the sun to flow through ecosystems and be used by all organisms.
Grade 9, U3-L1-Life on planet earth
The document discusses Earth's atmosphere and how it sustains life. It describes the atmosphere as a thin gaseous layer made up of 78% nitrogen and 21% oxygen that surrounds the planet. The atmosphere moderates temperatures, blocks ultraviolet light, and prevents excessive heating and cooling, maintaining an average surface temperature of 15°C. Without the atmosphere, most species would be unable to survive on Earth.
Grade9, U2-L7-Power generation, efficiency and cost of electricity
Electricity is generated at power stations from various energy sources like hydroelectric, nuclear, coal, wind, solar and natural gas. Generators transform this input energy into alternating current (AC) electrical energy, which is more efficient for long distance transmission than direct current (DC). Efficiency is a measure of the energy output versus input. Common rates for electricity are charged per kilowatt-hour, with time-of-use rates accounting for supply and demand. Calculating the cost to operate devices uses the power used, operating time and rate charged. An example compares the lower cost of a 13W CFL bulb versus a 60W incandescent bulb over 3 hours using time-of-use rates. Homework questions
Grade 9, U2-L6-Circuits
The document provides an overview of electric circuits and potential difference for a grade 9 science class. It introduces series and parallel circuits, defines electric potential difference, and discusses how to measure potential difference in series and parallel circuits. Key points covered include the relationships between voltages in series and parallel circuits and equations relating voltage, energy, charge, and work. Students are directed to practice questions and supplemental video resources are provided.
Grade 9, U2-L5 Equivalent Resistance and Complex CCT's
This document discusses circuits with resistance in series and parallel configurations. It explains that the total resistance (Req) of resistors in series can be calculated as the sum of the individual resistances (R1 + R2 + ... + Rn). For parallel resistors, the total resistance is calculated as the reciprocal of the sum of the reciprocals of the individual resistances (1/R1 + 1/R2 + ... + 1/Rn)-1. Complex circuits contain both series and parallel components, making them more difficult to solve for total resistance and current/voltage values. An example complex circuit is worked out on the chalkboard to demonstrate the analysis process.
Grade 9, U2-L4-Electrical quantities
This document defines and provides examples of key electrical quantities including electric charge, current, potential difference, resistance, and power. It explains that electric charge is measured in coulombs and is equal to the charge of approximately 6.2 x 1018 electrons. It also gives formulas for calculating current from charge and time, potential difference from energy and charge, and resistance from potential difference and current using Ohm's Law. Examples are provided for calculating charge, current, potential difference, resistance, and power.
Grade 9, U2-L3-Current electricity
The document defines key concepts in electric circuits including that electricity is the controlled flow of electrons through a conductor. An electric circuit provides a continuous path for electrons to flow and includes a power source, loads, and pathways that can be connected in series or parallel. Common circuit components are defined such as batteries, switches, resistors, motors, and their standard symbols.
Grade 9, U2-L2, Charging and Discharging Objects
An electroscope is used to test if an object is charged. It has a metal ball, rod, and leaves that allow electrons to move easily. When charged, the leaves separate. Charging can occur through contact or induction. Induction charges an object without direct contact by redistributing its electrons due to a nearby charged object. Lightning is a large-scale example of electrical discharge through induction in storm clouds.
Grade 9-U2-L1-Static electricity
This document introduces the topics of static electricity, current electricity, and power generation. It discusses what causes static electricity, such as walking across carpet and touching something to get a shock. Static electricity occurs when electrons are not moving along a path but rather build up as they move between atoms. The document also covers electric charge, conductors, insulators, and tools for detecting electric charge like electroscopes.
Grade 9, U1-L13-Molecular Compounds
This document defines molecular compounds and provides examples. It discusses that molecular compounds are composed of non-metal elements that are chemically bonded through covalent bonds where atoms share electron pairs. Examples of common molecular compounds are given such as gases, hydrocarbons, alcohols, carbohydrates, and biological molecules. Methods for drawing and naming molecular compounds such as Lewis dot diagrams and structural formulas are also outlined.
More from gruszecki1 (20)
Grade9, U2-L7-Power generation, efficiency and cost of electricity
Grade9, U2-L7-Power generation, efficiency and cost of electricity
Grade 9, U2-L5 Equivalent Resistance and Complex CCT's
Grade 9, U2-L5 Equivalent Resistance and Complex CCT's
Recently uploaded
A Strategic Approach: GenAI in Education
Artificial Intelligence (AI) technologies such as Generative AI, Image Generators and Large Language Models have had a dramatic impact on teaching, learning and assessment over the past 18 months. The most immediate threat AI posed was to Academic Integrity with Higher Education Institutes (HEIs) focusing their efforts on combating the use of GenAI in assessment. Guidelines were developed for staff and students, policies put in place too. Innovative educators have forged paths in the use of Generative AI for teaching, learning and assessments leading to pockets of transformation springing up across HEIs, often with little or no top-down guidance, support or direction.
This Gasta posits a strategic approach to integrating AI into HEIs to prepare staff, students and the curriculum for an evolving world and workplace. We will highlight the advantages of working with these technologies beyond the realm of teaching, learning and assessment by considering prompt engineering skills, industry impact, curriculum changes, and the need for staff upskilling. In contrast, not engaging strategically with Generative AI poses risks, including falling behind peers, missed opportunities and failing to ensure our graduates remain employable. The rapid evolution of AI technologies necessitates a proactive and strategic approach if we are to remain relevant.
Hindi varnamala | hindi alphabet PPT.pdf
हिंदी वर्णमाला पीपीटी, hindi alphabet PPT presentation, hindi varnamala PPT, Hindi Varnamala pdf, हिंदी स्वर, हिंदी व्यंजन, sikhiye hindi varnmala, dr. mulla adam ali, hindi language and literature, hindi alphabet with drawing, hindi alphabet pdf, hindi varnamala for childrens, hindi language, hindi varnamala practice for kids, https://www.drmullaadamali.com
RPMS TEMPLATE FOR SCHOOL YEAR 2023-2024 FOR TEACHER 1 TO TEACHER 3
RPMS Template 2023-2024 by: Irene S. Rueco
The Diamonds of 2023-2024 in the IGRA collection
A review of the growth of the Israel Genealogy Research Association Database Collection for the last 12 months. Our collection is now passed the 3 million mark and still growing. See which archives have contributed the most. See the different types of records we have, and which years have had records added. You can also see what we have for the future.
Your Skill Boost Masterclass: Strategies for Effective Upskilling
Your Skill Boost Masterclass: Strategies for Effective UpskillingExcellence Foundation for South Sudan
Strategies for Effective Upskilling is a presentation by Chinwendu Peace in a Your Skill Boost Masterclass organisation by the Excellence Foundation for South Sudan on 08th and 09th June 2024 from 1 PM to 3 PM on each day.The History of Stoke Newington Street Names
Presented at the Stoke Newington Literary Festival on 9th June 2024
www.StokeNewingtonHistory.com
Azure Interview Questions and Answers PDF By ScholarHat
Azure Interview Questions and Answers PDF By ScholarHat
How to Fix the Import Error in the Odoo 17
An import error occurs when a program fails to import a module or library, disrupting its execution. In languages like Python, this issue arises when the specified module cannot be found or accessed, hindering the program's functionality. Resolving import errors is crucial for maintaining smooth software operation and uninterrupted development processes.
Chapter 4 - Islamic Financial Institutions in Malaysia.pptx
Chapter 4 - Islamic Financial Institutions in Malaysia.pptxMohd Adib Abd Muin, Senior Lecturer at Universiti Utara Malaysia
This slide is special for master students (MIBS & MIFB) in UUM. Also useful for readers who are interested in the topic of contemporary Islamic banking.
CACJapan - GROUP Presentation 1- Wk 4.pdf
Macroeconomics- Movie Location
This will be used as part of your Personal Professional Portfolio once graded.
Objective:
Prepare a presentation or a paper using research, basic comparative analysis, data organization and application of economic information. You will make an informed assessment of an economic climate outside of the United States to accomplish an entertainment industry objective.
Advanced Java[Extra Concepts, Not Difficult].docx
This is part 2 of my Java Learning Journey. This contains Hashing, ArrayList, LinkedList, Date and Time Classes, Calendar Class and more.
Pollock and Snow "DEIA in the Scholarly Landscape, Session One: Setting Expec...
Pollock and Snow "DEIA in the Scholarly Landscape, Session One: Setting Expec...National Information Standards Organization (NISO)
This presentation was provided by Steph Pollock of The American Psychological Association’s Journals Program, and Damita Snow, of The American Society of Civil Engineers (ASCE), for the initial session of NISO's 2024 Training Series "DEIA in the Scholarly Landscape." Session One: 'Setting Expectations: a DEIA Primer,' was held June 6, 2024.Digital Artifact 1 - 10VCD Environments Unit
Digital Artifact 1 - 10VCD Environments Unit - NGV Pavilion Concept Design
The simplified electron and muon model, Oscillating Spacetime: The Foundation...
Discover the Simplified Electron and Muon Model: A New Wave-Based Approach to Understanding Particles delves into a groundbreaking theory that presents electrons and muons as rotating soliton waves within oscillating spacetime. Geared towards students, researchers, and science buffs, this book breaks down complex ideas into simple explanations. It covers topics such as electron waves, temporal dynamics, and the implications of this model on particle physics. With clear illustrations and easy-to-follow explanations, readers will gain a new outlook on the universe's fundamental nature.
How to Add Chatter in the odoo 17 ERP Module
In Odoo, the chatter is like a chat tool that helps you work together on records. You can leave notes and track things, making it easier to talk with your team and partners. Inside chatter, all communication history, activity, and changes will be displayed.
Assessment and Planning in Educational technology.pptx
In an education system, it is understood that assessment is only for the students, but on the other hand, the Assessment of teachers is also an important aspect of the education system that ensures teachers are providing high-quality instruction to students. The assessment process can be used to provide feedback and support for professional development, to inform decisions about teacher retention or promotion, or to evaluate teacher effectiveness for accountability purposes.
Recently uploaded (20)
Film vocab for eal 3 students: Australia the movie
Film vocab for eal 3 students: Australia the movie
RPMS TEMPLATE FOR SCHOOL YEAR 2023-2024 FOR TEACHER 1 TO TEACHER 3
RPMS TEMPLATE FOR SCHOOL YEAR 2023-2024 FOR TEACHER 1 TO TEACHER 3
Your Skill Boost Masterclass: Strategies for Effective Upskilling
Your Skill Boost Masterclass: Strategies for Effective Upskilling
Liberal Approach to the Study of Indian Politics.pdf
Liberal Approach to the Study of Indian Politics.pdf
Azure Interview Questions and Answers PDF By ScholarHat
Azure Interview Questions and Answers PDF By ScholarHat
Chapter 4 - Islamic Financial Institutions in Malaysia.pptx
Chapter 4 - Islamic Financial Institutions in Malaysia.pptx
Pollock and Snow "DEIA in the Scholarly Landscape, Session One: Setting Expec...
Pollock and Snow "DEIA in the Scholarly Landscape, Session One: Setting Expec...
The simplified electron and muon model, Oscillating Spacetime: The Foundation...
The simplified electron and muon model, Oscillating Spacetime: The Foundation...
Assessment and Planning in Educational technology.pptx
Assessment and Planning in Educational technology.pptx
Grade 11, Review topics for electricy test
- 1. Grade 11 Electricity Half Test Topics and format for test
- 2. • Know the equations and definitions for current and potential difference (voltage). • Know how to draw series and parallel circuits. This requires knowing symbols for battery, light bulb, switch, motor and resistor. • Know the relationships between current and potential difference in both types of circuits. • Know how to calculate equivalent resistance for CCT’s (for series, parallel and complex CCT’s) • Know how to use Ohm’s law and Kirchhoff’s node law. • Know the equations for adding resistances in series and in parallel circuits.
- 3. • Know how to connect ammeters and voltmeters in a circuit. Know the symbols for these devices. • Know what “shorting “ is and what the effect of having a load shorted is. • Format of half test: – Answering T/F and M/C questions. (3 t/f, 7 m/c) – Drawing a circuit – Analyzing a complex circuit (10 marks). This will require calculating currents through loads (resistances) and the potential differences across loads. You will have to calculate 5+ currents and 5+ voltages. – 25 total marks that are split into KICA categories .