This document provides an overview of a training session on energy equipment refrigeration and air conditioning systems. It discusses types of refrigeration including vapor compression and vapor absorption. It also covers assessing the performance of refrigeration and air conditioning systems, such as measuring tons of refrigeration and coefficient of performance. Finally, it lists several energy efficiency opportunities for refrigeration and AC systems, such as optimizing heat exchange, multi-staging systems, and capacity control of compressors.
Introduction to Refrigeration and Air Conditioning was explained in a detailed way. For more information, Visit https://mechanicalstudents.com/refrigeration-introduction-vapor-compression-refrigeration-system-vapor-absorption-refrigeration-system/
Refrigeration and Air Conditioning System ComponentsAjaypalsinh Barad
The ppt contains detailed study of all the components used in refrigeration and air conditioning system with neat sketches and description. It is well formed as per the syllabus of GTU
Refrigeration and air conditioning (full note)shone john
Principles of refrigeration: Thermodynamics of refrigeration - Carnot cycle,
reversed carnot cycle, heat pump, and refrigerating machine- coefficient of
performance - unit of refrigeration - refrigeration methods- conventional
refrigeration systems. Air refrigeration system- Bell Coleman cycle - C.O.P.
capacity work and refrigerant flow requirements in Bell - Coleman cycle.
Module 2
Vapour compression system: simple cycle -comparison with Carnot cycle -
theoretical, actual and reactive - COP effect of operating parameters on
COP - wet, dry and superheated compression - under cooling - actual cycle
representation on TS and PH diagrams simple problems. Advanced
vapour compression systems - multistage vapour compression systems -
flash chamber multiple compression and evaporation systems cascading -
simple problems.
Module 3
Vapour absorption systems: simple, cycles - actual cycle - ammonia water
and lithium bromide water systems - COP - electrolux system. Refrigerant
and their properties: Nomenclature - suitability of refrigerants for various
applications - unconventional refrigeration methods- Vortex tube, steamjet, magnetic (cryogenics) refrigeration and thermoelectric refrigeration -
applied refrigeration house hold refrigerators - unit air conditioners andModule 4
Refrigeration system components: condensers - water and air cooled
condensers - evaporative condensers - expansion devises - capillary tubeconstant pressure expansion valve - thermostatic expansion valve - float
valve and solenoid valve - evaporators - natural convection coils - flooded
evaporators - direct expansion coils. Reciprocating compressors: single
stage and multistage compressors - work done optimum pressure ratioeffect of interfolding - volumetric efficiency -effect of clearance -
isothermal and adiabatic efficiency - compressed air motors. Rotodynamic
compressors: Screw and vane type compressors - principle of operation -
hermetic, semihermetic and open type refrigeration compressors.
Module 5
Principles of air conditioning: Psychrometry and psychrometric chart
thermodynamics of human comfort - effective temperature - comfort chart
applied psychrometry - sensible heat factor - psychometric processproblems. Winter air conditioning: heating load calculations humidifiers
and humidistat. Summer air conditioning: cooling load calculations - year
round air conditioning - unitary and central systems - principles of air
distribution - design of air duct systems.
References
1. Refrigeration and air conditioning - Ballaney P. L.
2. Refrigeration and air conditioning - Stocker W. F.
3. Refrigeration and air conditioning - Jordan and Protester
4. Principles of Refrigeration - Roy J. Dossat
The ppt contains detailed study of Vapor Absorption Refrigeration System with neat sketches and description. It is well formed as per the syllabus of GTU
Introduction to Refrigeration and Air Conditioning was explained in a detailed way. For more information, Visit https://mechanicalstudents.com/refrigeration-introduction-vapor-compression-refrigeration-system-vapor-absorption-refrigeration-system/
Refrigeration and Air Conditioning System ComponentsAjaypalsinh Barad
The ppt contains detailed study of all the components used in refrigeration and air conditioning system with neat sketches and description. It is well formed as per the syllabus of GTU
Refrigeration and air conditioning (full note)shone john
Principles of refrigeration: Thermodynamics of refrigeration - Carnot cycle,
reversed carnot cycle, heat pump, and refrigerating machine- coefficient of
performance - unit of refrigeration - refrigeration methods- conventional
refrigeration systems. Air refrigeration system- Bell Coleman cycle - C.O.P.
capacity work and refrigerant flow requirements in Bell - Coleman cycle.
Module 2
Vapour compression system: simple cycle -comparison with Carnot cycle -
theoretical, actual and reactive - COP effect of operating parameters on
COP - wet, dry and superheated compression - under cooling - actual cycle
representation on TS and PH diagrams simple problems. Advanced
vapour compression systems - multistage vapour compression systems -
flash chamber multiple compression and evaporation systems cascading -
simple problems.
Module 3
Vapour absorption systems: simple, cycles - actual cycle - ammonia water
and lithium bromide water systems - COP - electrolux system. Refrigerant
and their properties: Nomenclature - suitability of refrigerants for various
applications - unconventional refrigeration methods- Vortex tube, steamjet, magnetic (cryogenics) refrigeration and thermoelectric refrigeration -
applied refrigeration house hold refrigerators - unit air conditioners andModule 4
Refrigeration system components: condensers - water and air cooled
condensers - evaporative condensers - expansion devises - capillary tubeconstant pressure expansion valve - thermostatic expansion valve - float
valve and solenoid valve - evaporators - natural convection coils - flooded
evaporators - direct expansion coils. Reciprocating compressors: single
stage and multistage compressors - work done optimum pressure ratioeffect of interfolding - volumetric efficiency -effect of clearance -
isothermal and adiabatic efficiency - compressed air motors. Rotodynamic
compressors: Screw and vane type compressors - principle of operation -
hermetic, semihermetic and open type refrigeration compressors.
Module 5
Principles of air conditioning: Psychrometry and psychrometric chart
thermodynamics of human comfort - effective temperature - comfort chart
applied psychrometry - sensible heat factor - psychometric processproblems. Winter air conditioning: heating load calculations humidifiers
and humidistat. Summer air conditioning: cooling load calculations - year
round air conditioning - unitary and central systems - principles of air
distribution - design of air duct systems.
References
1. Refrigeration and air conditioning - Ballaney P. L.
2. Refrigeration and air conditioning - Stocker W. F.
3. Refrigeration and air conditioning - Jordan and Protester
4. Principles of Refrigeration - Roy J. Dossat
The ppt contains detailed study of Vapor Absorption Refrigeration System with neat sketches and description. It is well formed as per the syllabus of GTU
Slide deals with the brief explanation on refrigeration which is one of the most important application of our lives.
The slide will be helpful for students studying Basic Mechanical engineering.
Buying a refrigerator freezer combo isn’t the easiest thing in the world. First, most companies often have a poor selection. Other companies may overcharge for poor-quality products. Most commercial display coolers manufactures also don’t offer an adequate warranty policy to insure your investment. If you’re looking for a new commercial cooler or a refrigerator freezer combo for your business, then you should look no further than http://srcrefrigeration.com/
The ppt contains detailed study of refrigerants used in refrigeration and air conditioning system with description. It is well formed as per the syllabus of GTU.
Air compressors:- One of the important device used to compress air at high pressure.
The presentation contains a detailed information about air compressors, classification of air compressors, reciprocating air compressors, rotary type, multistage/ single stage compressors. advantages and lastly application/ uses of air compressors.
Hope You like the presentation.
Sales Management by Dr. Charles M. Futrell (Professor of Marketing in the Mays College of Business at Texas A&M University in College Station, Texas)
Part I Introduction To Sales Management
Part II Planning The Sales Team's Efforts
Part III Staffing the Sales Team
Part IV Training the Sales Team
Part VI Controlling The Sales Team
Energy efficiency in Refrigeration Systemseecfncci
HVAC and refrigeration systems consume a lot of electricity in Nepalese Industries. Therefore, improving the efficiency of these systems can lead to huge cost savings. This presentation was held in the context of energy auditor training in Nepal in 2012 that was supported GIZ/NEEP Programme.
Industrial refrigeration systems are a significant consumer of electrical energy in food processing, cold storage, and chemical processing industries throughout the Midwestern United States.
This webinar, presented by Bryan Hackett, P.E., of kW Engineering, will covered the following topics:
• The basics of industrial refrigeration systems,
• A review of proven energy efficiency measures (EEMs) and how to identify potential applications for each, and
• The respective energy and cost savings for each.
Industrial and commercial utility program managers, end-user plant managers, refrigeration system operators, contractors, and solution vendors will get a better understanding of industrial refrigeration as an integrated system, how key components can be optimized to improve efficiency, and the energy and financial motivations for pursuing the discussed EEMs
Bryan Hackett, P.E. - Senior Engineer II, kW Engineering
Bryan leads kW Engineering’s Industrial Services Team, providing energy and water auditing, retro-commissioning, technical support services, and implementation management to industrial facilities across the country. Bryan has performed over 150 industrial energy audits and is the lead author of two papers on energy savings at food processing and refrigeration facilities. Bryan is a licensed Professional Mechanical Engineer with over 17 years of experience working with commercial, institutional, and industrial clients. As one of the leaders of kW's technical staff of 47 engineers, Bryan takes great pride in getting CFOs excited about sustainability by delivering results at the meter and on the bill.
Instructions for Submissions thorugh G- Classroom.pptxJheel Barad
This presentation provides a briefing on how to upload submissions and documents in Google Classroom. It was prepared as part of an orientation for new Sainik School in-service teacher trainees. As a training officer, my goal is to ensure that you are comfortable and proficient with this essential tool for managing assignments and fostering student engagement.
Welcome to TechSoup New Member Orientation and Q&A (May 2024).pdfTechSoup
In this webinar you will learn how your organization can access TechSoup's wide variety of product discount and donation programs. From hardware to software, we'll give you a tour of the tools available to help your nonprofit with productivity, collaboration, financial management, donor tracking, security, and more.
How to Make a Field invisible in Odoo 17Celine George
It is possible to hide or invisible some fields in odoo. Commonly using “invisible” attribute in the field definition to invisible the fields. This slide will show how to make a field invisible in odoo 17.
Students, digital devices and success - Andreas Schleicher - 27 May 2024..pptxEduSkills OECD
Andreas Schleicher presents at the OECD webinar ‘Digital devices in schools: detrimental distraction or secret to success?’ on 27 May 2024. The presentation was based on findings from PISA 2022 results and the webinar helped launch the PISA in Focus ‘Managing screen time: How to protect and equip students against distraction’ https://www.oecd-ilibrary.org/education/managing-screen-time_7c225af4-en and the OECD Education Policy Perspective ‘Students, digital devices and success’ can be found here - https://oe.cd/il/5yV
The French Revolution, which began in 1789, was a period of radical social and political upheaval in France. It marked the decline of absolute monarchies, the rise of secular and democratic republics, and the eventual rise of Napoleon Bonaparte. This revolutionary period is crucial in understanding the transition from feudalism to modernity in Europe.
For more information, visit-www.vavaclasses.com
How to Create Map Views in the Odoo 17 ERPCeline George
The map views are useful for providing a geographical representation of data. They allow users to visualize and analyze the data in a more intuitive manner.
Operation “Blue Star” is the only event in the history of Independent India where the state went into war with its own people. Even after about 40 years it is not clear if it was culmination of states anger over people of the region, a political game of power or start of dictatorial chapter in the democratic setup.
The people of Punjab felt alienated from main stream due to denial of their just demands during a long democratic struggle since independence. As it happen all over the word, it led to militant struggle with great loss of lives of military, police and civilian personnel. Killing of Indira Gandhi and massacre of innocent Sikhs in Delhi and other India cities was also associated with this movement.
Unit 8 - Information and Communication Technology (Paper I).pdfThiyagu K
This slides describes the basic concepts of ICT, basics of Email, Emerging Technology and Digital Initiatives in Education. This presentations aligns with the UGC Paper I syllabus.
The Roman Empire A Historical Colossus.pdfkaushalkr1407
The Roman Empire, a vast and enduring power, stands as one of history's most remarkable civilizations, leaving an indelible imprint on the world. It emerged from the Roman Republic, transitioning into an imperial powerhouse under the leadership of Augustus Caesar in 27 BCE. This transformation marked the beginning of an era defined by unprecedented territorial expansion, architectural marvels, and profound cultural influence.
The empire's roots lie in the city of Rome, founded, according to legend, by Romulus in 753 BCE. Over centuries, Rome evolved from a small settlement to a formidable republic, characterized by a complex political system with elected officials and checks on power. However, internal strife, class conflicts, and military ambitions paved the way for the end of the Republic. Julius Caesar’s dictatorship and subsequent assassination in 44 BCE created a power vacuum, leading to a civil war. Octavian, later Augustus, emerged victorious, heralding the Roman Empire’s birth.
Under Augustus, the empire experienced the Pax Romana, a 200-year period of relative peace and stability. Augustus reformed the military, established efficient administrative systems, and initiated grand construction projects. The empire's borders expanded, encompassing territories from Britain to Egypt and from Spain to the Euphrates. Roman legions, renowned for their discipline and engineering prowess, secured and maintained these vast territories, building roads, fortifications, and cities that facilitated control and integration.
The Roman Empire’s society was hierarchical, with a rigid class system. At the top were the patricians, wealthy elites who held significant political power. Below them were the plebeians, free citizens with limited political influence, and the vast numbers of slaves who formed the backbone of the economy. The family unit was central, governed by the paterfamilias, the male head who held absolute authority.
Culturally, the Romans were eclectic, absorbing and adapting elements from the civilizations they encountered, particularly the Greeks. Roman art, literature, and philosophy reflected this synthesis, creating a rich cultural tapestry. Latin, the Roman language, became the lingua franca of the Western world, influencing numerous modern languages.
Roman architecture and engineering achievements were monumental. They perfected the arch, vault, and dome, constructing enduring structures like the Colosseum, Pantheon, and aqueducts. These engineering marvels not only showcased Roman ingenuity but also served practical purposes, from public entertainment to water supply.
We all have good and bad thoughts from time to time and situation to situation. We are bombarded daily with spiraling thoughts(both negative and positive) creating all-consuming feel , making us difficult to manage with associated suffering. Good thoughts are like our Mob Signal (Positive thought) amidst noise(negative thought) in the atmosphere. Negative thoughts like noise outweigh positive thoughts. These thoughts often create unwanted confusion, trouble, stress and frustration in our mind as well as chaos in our physical world. Negative thoughts are also known as “distorted thinking”.
How to Split Bills in the Odoo 17 POS ModuleCeline George
Bills have a main role in point of sale procedure. It will help to track sales, handling payments and giving receipts to customers. Bill splitting also has an important role in POS. For example, If some friends come together for dinner and if they want to divide the bill then it is possible by POS bill splitting. This slide will show how to split bills in odoo 17 POS.
Ethnobotany and Ethnopharmacology:
Ethnobotany in herbal drug evaluation,
Impact of Ethnobotany in traditional medicine,
New development in herbals,
Bio-prospecting tools for drug discovery,
Role of Ethnopharmacology in drug evaluation,
Reverse Pharmacology.
TO THE TRAINER This PowerPoint presentation can be used to train people about the basics of refrigeration and air condonditioning. The information on the slides is the minimum information that should be explained. The trainer notes for each slide provide more detailed information, but it is up to the trainer to decide if and how much of this information is presented also. Additional materials that can be used for the training session are available on www.energyefficiencyasia.org under “Energy Equipment” and include: Textbook chapter on this energy equipment that forms the basis of this PowerPoint presentation but has more detailed information Quiz – ten multiple choice questions that trainees can answer after the training session Option checklist – a list of the most important options to improve energy efficiency of this equipment
Refrigeration and air conditioning is used to cool products or a building environment. The refrigeration or air conditioning system (R) transfers heat from a cooler low-energy reservoir to a warmer high-energy reservoir
There are several heat transfer loops in a refrigeration system as shown in Figure 2. Thermal energy moves from left to right as it is extracted from the space and expelled into the outdoors through five loops of heat transfer: Indoor air loop . In the left loop, indoor air is driven by the supply air fan through a cooling coil, where it transfers its heat to chilled water. The cool air then cools the building space. Chilled water loop . Driven by the chilled water pump, water returns from the cooling coil to the chiller’s evaporator to be re-cooled. Refrigerant loop . Using a phase-change refrigerant, the chiller’s compressor pumps heat from the chilled water to the condenser water. Condenser water loop . Water absorbs heat from the chiller’s condenser, and the condenser water pump sends it to the cooling tower. Cooling tower loop . The cooling tower’s fan drives air across an open flow of the hot condenser water, transferring the heat to the outdoors.
Depending on applications, there are several options / combinations of air conditioning, which are available for use: Air conditioning (for space or machines) Split air conditioners Fan coil units in a larger system Air handling units in a larger system
The following refrigeration systems exist for industrial processes (e.g. chilling plants) and domestic purposes (modular units, i.e. refrigerators): Small capacity modular units of the direct expansion type similar to domestic refrigerators. Centralized chilled water plants with chilled water as a secondary coolant for a temperature range over typically 5 oC. They can also be used for ice bank formation. Brine plants, which use brines as a lower temperature, secondary coolant for typically sub-zero temperature applications, which come as modular unit capacities as well as large centralized plant capacities. The plant capacities up to 50 TR (tons of refrigeration) are usually considered as small capacity, 50 – 250 TR as medium capacity and over 250 TR as large capacity units.
A large company may have a bank of units, often with common chilled water pumps, condenser water pumps, cooling towers, as an off site utility. The same company may also have two or three levels of refrigeration and air conditioning such as a combination of: Comfort air conditioning (20 – 25 oC) Chilled water system (8 – 10 oC) Brine system (sub-zero applications)
This section include various types of refrigeration such as Vapour Compression Refrigeration and Vapour Absorption Refrigeration system
The two principle types of refrigeration plants found in industrial use are: Vapour compression refrigeration (VCR) and vapour absorption refrigeration (VAR). VCR uses mechanical energy as the driving force for refrigeration, while VAR uses thermal energy as the driving force for refrigeration.
Compression refrigeration cycles take advantage of the fact that highly compressed fluids at a certain temperature tend to get colder when they are allowed to expand. If the pressure change is high enough, then the compressed gas will be hotter than our source of cooling (outside air, for instance) and the expanded gas will be cooler than our desired cold temperature. In this case, fluid is used to cool a low temperature environment and reject the heat to a high temperature environment.
Vapour compression refrigeration cycles have two advantages. First, a large amount of thermal energy is required to change a liquid to a vapor, and therefore a lot of heat can be removed from the air-conditioned space. Second, the isothermal nature of the vaporization allows extraction of heat without raising the temperature of the working fluid to the temperature of whatever is being cooled. This means that the heat transfer rate remains high, because the closer the working fluid temperature approaches that of the surroundings, the lower the rate of heat transfer.
The refrigeration cycle is shown in the Figure and can be broken down into the following stages (note to the trainer: the next slides will explain what is happening between 1 to 4)
The refrigeration cycle is shown in the Figure and can be broken down into the following stages (note to the trainer: the numbers 1-4 are shown in the figure) : 1 – 2. Low-pressure liquid refrigerant in the evaporator absorbs heat from its surroundings, usually air, water or some other process liquid. During this process it changes its state from a liquid to a gas, and at the evaporator exit is slightly superheated.
The refrigeration cycle is shown in the Figure and can be broken down into the following stages (note to the trainer: the numbers 1-4 are shown in the figure) : 2 – 3. The superheated vapour enters the compressor where its pressure is raised. The temperature will also increase, because a proportion of the energy put into the compression process is transferred to the refrigerant.
The refrigeration cycle is shown in the Figure and can be broken down into the following stages (note to the trainer: the numbers 1-4 are shown in the figure) : 3 – 4. The high pressure superheated gas passes from the compressor into the condenser. The initial part of the cooling process (3-3a) de-superheats the gas before it is then turned back into liquid (3a-3b). The cooling for this process is usually achieved by using air or water. A further reduction in temperature happens in the pipe work and liquid receiver (3b - 4), so that the refrigerant liquid is sub-cooled as it enters the expansion device
The refrigeration cycle is shown in the Figure and can be broken down into the following stages (note to the trainer: the numbers 1-4 are shown in the figure) : 1 – 2. Low-pressure liquid refrigerant in the evaporator absorbs heat from its surroundings, usually air, water or some other process liquid. During this process it changes its state from a liquid to a gas, and at the evaporator exit is slightly superheated. 2 – 3. The superheated vapour enters the compressor where its pressure is raised. The temperature will also increase, because a proportion of the energy put into the compression process is transferred to the refrigerant. 3 – 4. The high pressure superheated gas passes from the compressor into the condenser. The initial part of the cooling process (3-3a) de-superheats the gas before it is then turned back into liquid (3a-3b). The cooling for this process is usually achieved by using air or water. A further reduction in temperature happens in the pipe work and liquid receiver (3b - 4), so that the refrigerant liquid is sub-cooled as it enters the expansion device.CondenserEvaporatorHigh Pressure SideLow Pressure SideCompressorExpansion Device 1234 4 - 1 The high-pressure sub-cooled liquid passes through the expansion device, which both reduces its pressure and controls the flow into the evaporator
A variety of refrigerants are used in vapor compression systems. The choice of fluid is determined largely by the cooling temperature required. Commonly used refrigerants are in the family of chlorinated fluorocarbons, CFCs, also known as freons: R-11, R-12, R-21, R-22 and R-502.
The choice of refrigerant and the required cooling temperature and load determine the choice of compressor, as well as the design of the condenser, evaporator, and other auxiliaries. Additional factors such as ease of maintenance, physical space requirements and availability of utilities for auxiliaries (water, power, etc.) also influence component selection.
The vapour absorption refrigeration system consists of: Evaporator Absorber High pressure generator Condenser The next slides discuss each of these in more detail.
Evaporator The refrigerant (water) evaporates at around 4oC under a high vacuum condition of 754 mm Hg in the evaporator. Chilled water goes through heat exchanger tubes in the evaporator and transfers heat to the evaporated refrigerant. The evaporated refrigerant (vapor) turns into liquid again, while the latent heat from this vaporization process cools the chilled water (in the diagram from 12 oC to 7 oC). The chilled water is then used for cooling purposes.
Absorber In order to keep evaporating, the refrigerant vapor must be discharged from the evaporator and refrigerant (water) must be supplied. The refrigerant vapor is absorbed into lithium bromide solution, which is convenient to absorb the refrigerant vapor in the absorber. The heat generated in the absorption process is continuously removed from the system by cooling water. The absorption also maintains the vacuum inside the evaporator.
High Pressure Generator As lithium bromide solution is diluted, the ability to absorb the refrigerant vapor reduces. In order to keep the absorption process going, the diluted lithium bromide solution must be concentrated again. An absorption chiller is provided with a solution concentrating system, called a generator. Heating media such as steam, hot water, gas or oil perform the function of concentrating solutions.The concentrated solution is returned to the absorber to absorb refrigerant vapor again.
Condenser To complete the refrigeration cycle, and thereby ensuring the refrigeration takes place continuously, the following two functions are required To concentrate and liquefy the evaporated refrigerant vapor, which is generated in the high-pressure generator. To supply the condensed water to the evaporator as refrigerant (water) For these two functions a condenser is installed.
There are occasions where air conditioning, which stipulates control of humidity up to 50 % for human comfort or for process, can be replaced by a much cheaper and less energy intensive evaporative cooling. Evaporative cooling is an extremely efficient means of cooling at very low cost. The concept is very simple and is the same as that used in a cooling tower. Air is brought in close contact with water to cool it to a temperature close to the wet bulb temperature. The cool air can be used for comfort or process cooling. The disadvantage is that the air is rich in moisture. The possibility of evaporative cooling is especially attractive for comfort cooling in dry regions. This principle is practiced in textile industries for certain processes.
This section include performance evaluation of refrigeration plant and examples for the assessment of refrigeration plant.
The cooling effect produced is quantified as to ns of refrigeration, or shortly TR. 1 TR of refrigeration = 3024 kCal/hr heat rejected. The refrigeration TR is assessed as TR = Q x Cp x (Ti – To) / 3024, where Q is mass flow rate of coolant; Cp is coolant specific heat in; Ti is inlet, temperature of coolant to evaporator; and To is outlet temperature of coolant from evaporator. The above TR is also called as chiller tonnage.
The specific power consumption kW/TR is a useful indicator of the performance of a refrigeration system. By measuring the refrigeration duty performed in TR and the kW inputs, kW/TR is used as an energy performance indicator. In a centralized chilled water system, apart from the compressor unit, power is also consumed by the chilled water (secondary) coolant pump, the condenser water pump (for heat rejection to cooling tower) and the fan in the cooling tower. Effectively, the specific power consumption for a certain TR output is the sum of: Compressor kW/TR Chilled water pump kW/TR Condenser water pump kW/TR Cooling tower fan kW/TR
The theoretical Coefficient of Performance (Carnot), (COPCarnot, a standard measure of refrigeration efficiency of an ideal refrigeration system) depends on two key system temperatures: evaporator temperature Te and condenser temperature Tc. COP is given as: COPCarnot = Te / (Tc - Te) (Click once) But COPCarnot is only a ratio of temperatures, and does not take into account the type of compressor. Hence the COP normally used in industry is calculated using the equation on the slide
COPCarnot = Te / (Tc - Te) This expression also indicates that higher COPCarnot is achieved with higher evaporator temperatures and lower condenser temperatures.
In case of air conditioning units, the airflow at the fan coil units or the air handling units can be measured with an anemometer. Dry bulb and wet bulb temperatures are measured at the inlet and outlet of AHU or the FCU. The refrigeration load in TR is assessed as: TR = Q x x ( h in - h out) / 3024. Where Q is the air flow; is density of air; h in is enthalpy of inlet air; and h out is enthalpy of outlet air. Use of psychometric charts can help to calculate hin and hout from dry bulb and wet bulb temperature values which are measured during trials by a whirling psychrometer. Power measurements at compressor, pumps, AHU fans, cooling tower fans can be taken with a portable load analyzer. The specific power consumption can then be calculated.
An indicative TR load profile for air conditioning is presented as follows: Small office cabins = 0.1 TR/m2 Medium size office i.e., = 0.06 TR/m2 10 – 30 people occupancy with central A/C Large multistoried office = 0.04 TR/m2 complexes with central A/C
Accuracy of flow and temperature measurements In a field performance assessment, accurate instruments are required to measure the Inlet and outlet temperatures of chilled water and condenser water, preferably with a count of at least 0.1 oC. Flow measurements of chilled water can be made with an ultrasonic flow meter directly or can be determined based on pump duty parameters. Condenser water flow can also be measured with a non-contact flow meter directly or determined by using pump duty parameters. Integrated Part Load Value (IPLV) Although the kW/ TR can serve as an initial reference, it should not be taken as an absolute since this value is based on a 100% equipment capacity level. But most equipment operate between 50% and 75% of their capacity. To overcome this, an average kW/TR with partial loads has to be determined, which is called the Integrated Part Load Value (IPLV). The IPLV is the most appropriate reference, although not considered the best, because it only captures four points within the operational cycle: 100%, 75%, 50% and 25%. Furthermore, it assigns the same weight to each value, and most equipment operate between 50% and 75% of their capacity.
Energy efficiency opportunities.
We will go through the following eight areas for energy efficiency improvements.
There is a tendency to apply high safety margins to operations, which influence the compressor suction pressure / evaporator set point. For instance, a process-cooling requirement of 15 oC would need chilled water at a lower temperature, but the range can vary from 6 oC to about 10 oC. At chilled water of 10 oC, the refrigerant side temperature has to be lower (about –5oC to +5oC). The refrigerant temperature determines the corresponding suction pressure of the refrigerant, which in turn determines the inlet duty conditions for the refrigerant compressor. Minimizing energy consumption can be achieved in the following ways: Proper sizing of heat transfer areas of process heat exchangers and evaporators the heat transfer coefficient on the refrigerant side can range from 1400 – 2800 watts /m2K. The refrigerant side heat transfer areas are of the order of 0.5 m2/TR and above in evaporators 2. Optimizing the driving force, i.e. the difference between evaporator temp Te and condensing temp Tc. A 1oC raise in evaporator temperature can save almost 3 % of the power consumed. The next slide shows the effect of Te and Tc on the cooling effect TR and the power consumption
This table shows the effect of evaporation temperature on the compressor power consumption. At a constant condenser temperature Tc of 40oC, lower evaporator temperatures reduce the refrigeration capacity TR and increase the power consumption The second table shows the effect of condensing temperature on the compressor power consumption. At a constant evaporator temperature Te of 10oC, increasing the condensing temperature leads to a reduction in refrigeration capacity and an increase in power consumption. The conclusion is therefore that you try to keep the difference between Te and Tc at an optimum level to ensure the best TR at the lowest power consumption.
3. Selection of condensers The choice of condensers in practice is between air-cooled, air-cooled with water spray, and shell and tube condensers with water-cooling. Larger shell and tube heat exchangers (0.65 m2/TR and above) that are used as condensers and that are equipped with good cooling tower operations allow operation at low discharge pressure values and improve the TR capacity of the refrigeration plant and thus reduce the power consumption. For example (optional) If the refrigerant R22 is used in a water-cooled shell and tube condenser then the discharge pressure is 15 kg/cm2. If the same refrigerant is used in an air-cooled condenser then the discharge pressure is 20 kg/cm2. This shows how much additional compression duty is required, which results in almost 30 % additional energy consumption by the plant.
Once compressors have been purchased, effective maintenance is the key to optimizing power consumption. Poor maintenance forces a compressor to work harder, which results in increased power consumption A maintenance checklist for the condenser and evaporator Ensuring proper separation of the lubricating oil and the refrigerant Timely defrosting of coils Increasing the velocity of the secondary coolant (air, water, etc.). Equally important is proper selection, sizing, and maintenance of cooling towers. A reduction of 0.55oC in temperature of the water returning from the cooling tower reduces compressor power consumption by 3%.
This table shows the effect of poor maintenance of compressor power consumption. For example, a dirty condenser and evaporator can increase the power consumption per ton of refrigeration (TR) by 38%!
Efficient compressor operation requires that the compression ratio be kept low, to reduce discharge pressure and temperature. For low temperature applications involving high compression ratios, and for wide temperature range requirements, it is preferable (due to equipment design limitations) and often economical to employ multi-stage reciprocating machines or centrifugal / screw compressors. There are two types of multi-staging systems, which are applicable to all types of compressors: compound and cascade.
Efficient compressor operation requires that the compression ratio be kept low, to reduce discharge pressure and temperature. For low temperature applications involving high compression ratios, and for wide temperature range requirements, it is preferable (due to equipment design limitations) and often economical to employ multi-stage reciprocating machines or centrifugal / screw compressors. There are two types of multi-staging systems, which are applicable to all types of compressors: compound and cascade. Compound a combination of two compressors with low compression ratios can provide a high compression ratio A single refrigerant is used in the system, and the two compressors share the compression task equally. a first-stage compressor that sized to meet the cooling load, feeds into the suction of a second-stage compressor after inter-cooling of the gas. A part of the high-pressure liquid from the condenser is flashed and used for liquid sub-cooling. The second compressor, therefore, has to meet the load of the evaporator and the flash gas. Cascade For temperatures in the range of –46oC to –101oC, cascaded systems are preferable. In this system, two separate systems using different refrigerants are connected so that one rejects heat to the other. The main advantage of this system is that a low temperature refrigerant, which has a high suction temperature and low specific volume, can be selected for the low-stage to meet very low temperature requirements.
Consideration of part-load operation is important, because most refrigeration applications have varying loads. The load may vary due to variations in temperature and process cooling needs. During part-load operation, the evaporator temperature rises and the condenser temperature falls, effectively increasing the COP. But at the same time, deviation from the design operation point and the fact that mechanical losses form a greater proportion of the total power negate the effect of improved COP, resulting in lower part-load efficiency. Matching refrigeration capacity to the load is a difficult exercise, requiring knowledge of compressor performance, and variations in ambient conditions, and detailed knowledge of the cooling load.
The capacity of compressors is controlled in a number of ways. We will discuss four of these Capacity control through cylinder unloading, vanes and valves Capacity control of reciprocating compressors through cylinder unloading results in incremental (step-by-step) modulation. In contrast, continuous modulation occurs in centrifugal compressors through vane control and in screw compressors through sliding valves. Capacity regulation through speed control is the most efficient option. Reciprocating compressors: it should be ensured that the lubrication system is not affected. Centrifugal compressors: restrict speed control to about 50 % of the capacity to prevent surging. Below 50%, vane control or hot gas bypass can be used for capacity modulation.
Temperature control requires careful system design. Reciprocating compressors: for widely varying loads control the compressor by monitoring the return water (or other secondary coolant) temperature. If load fluctuations are not high: the temperature of the water leaving the chiller should be monitored. The outgoing water temperature should be monitored for centrifugal and screw chillers. Capacity regulation through speed control is the most efficient option. The efficiency of screw compressors operating at part load is generally higher than either centrifugal compressors or reciprocating compressors, which may make them attractive in situations where part-load operation is common.
Managing part-load at bank of compressors at central plant Many industries use a bank of compressors at a central location to meet the load. Usually the chillers feed into a common header from which branch lines are taken to different locations in the plant. In such situations, operation at part-load requires extreme care. For efficient operation, the cooling load, and the load on each chiller must be monitored closely. It is more efficient to operate a single chiller at full load than to operate two chillers at part-load. The distribution system should be designed such that individual chillers can feed all branch lines. Isolation valves must be provided to ensure that chilled water (or other coolant) does not flow through chillers not in operation. Valves should also be provided on branch lines to isolate sections where cooling is not required. This reduces pressure drops in the system and reduces power consumption in the pumping system. Individual compressors should be loaded to their full capacity before operating the second compressor. In some cases it is economical to provide a separate smaller capacity chiller, which can be operated on an on-off control to meet peak demands, with larger chillers meeting the base load.
Packaged units Packaged units can be used For diverse applications requiring a wide range of temperatures depending on the distance at which cooling loads need to be met. Packaged units at load centers reduce distribution losses in the system. Advantages: Economical, flexibility and reliability. Despite the advantages of packaged units, central plants generally have lower power consumption since at reduced loads power consumption can reduce significantly due to the large condenser and evaporator surfaces. Flow control Flow control is also commonly used to meet varying demands. Reduced flow. In such cases the savings in pumping at reduced flow should be weighed against the reduced heat transfer in coils due to reduced velocity. In some cases, operation at normal flow rates, with subsequent longer periods of no-load (or shut-off) operation of the compressor, may result in larger savings.
Depending on the nature of the load, it is economical to provide a chilled water storage facility with very good cold insulation. Also, the storage facility can be fully filled to meet the process requirements so that chillers need not be operated continuously. This system is usually economical if small variations in temperature are acceptable. This system has the added advantage of allowing the chillers to be operated at periods of low electricity demand to reduce peak demand charges. Low tariffs offered by some electric utilities for operation at nighttime can also be taken advantage of by using a storage facility. An added benefit is that lower ambient temperature at night lowers condenser temperature and thereby increases the COP. If temperature variations cannot be tolerated, it may not be economical to provide a storage facility since the secondary coolant would have to be stored at a temperature much lower than required to provide for heat gain. The additional cost of cooling to a lower temperature may offset the benefits. The solutions are case specific. For example, in some cases it may be possible to employ large heat exchangers, at a lower cost burden than low temperature chiller operation, to take advantage of the storage facility even when temperature variations are not acceptable. Ice bank systems, which store ice rather than water, are often economical.
In overall plant design, adoption of good practices improves the energy efficiency significantly. Some areas for consideration are: Design of cooling towers with FRP impellers and film fills, PVC drift eliminators, etc. Use of softened water for condensers in place of raw water. Use of economic insulation thickness on cold lines, heat exchangers, considering cost of heat gains and adopting practices like infrared thermography for monitoring - applicable especially in large chemical / fertilizer / process industry. Adoption of roof coatings / cooling systems, false ceilings / as applicable, to minimize refrigeration load. Adoption of energy efficient heat recovery devices like air to air heat exchangers to pre-cool the fresh air by indirect heat exchange; control of relative humidity through indirect heat exchange rather than use of duct heaters after chilling. Adopting of variable air volume systems Adopting of sun film application for heat reflection Optimizing lighting loads in the air conditioned areas Optimizing number of air changes in the air conditioned areas are few other examples.