This document is a report on a study of cooling towers conducted by five mechanical engineering students at Delhi Technological University. It provides an overview of cooling towers, including their components, materials, types, and ways to assess performance and increase energy efficiency. The two main types are natural draft towers, which use temperature differences to circulate air without fans, and mechanical draft towers, which use large fans. The report evaluates selecting the right tower, fill media effects, pumps, distribution systems, fans and more to optimize efficiency. It includes acknowledgments, objectives, figures, tables, and conclusions from the study.
PRINCIPAL OF COOLING TOWER
TYPES OF COOLING TOWER
DIFFERENT TERMS USED IN COOLING TOWER SPECIFICATION
AIR PROPERTIES AND
SIZING OF COOLING TOWER HEIGHT
TYPICAL SPECIFICATION FORMAT / DATASHEET
A cooling tower is a heat rejection device which extracts waste heat to the atmosphere through the cooling of a water stream to a lower temperature.
A cooling tower is a heat rejection device which extracts waste heat to the atmosphere through the cooling of a water stream to a lower temperature. Cooling towers may either use the evaporation of water to remove process heat and cool the working fluid to near the wet-bulb air temperature or, in the case of closed circuit dry cooling towers, rely solely on air to cool the working fluid to near the dry-bulb air temperature.
Common applications include cooling the circulating water used in oil refineries, petrochemical and other chemical plants, thermal power stations and HVAC systems for cooling buildings. The classification is based on the type of air induction into the tower: the main types of cooling towers are natural draft and induced draft cooling towers.
Cooling towers vary in size from small roof-top units to very large hyperboloid structures (as in the adjacent image) that can be up to 200 metres (660 ft) tall and 100 metres (330 ft) in diameter, or rectangular structures that can be over 40 metres (130 ft) tall and 80 metres (260 ft) long. The hyperboloid cooling towers are often associated with nuclear power plants,[1] although they are also used to some extent in some large chemical and other industrial plants. Although these large towers are very prominent, the vast majority of cooling towers are much smaller, including many units installed on or near buildings to discharge heat from air conditioning.
PRINCIPAL OF COOLING TOWER
TYPES OF COOLING TOWER
DIFFERENT TERMS USED IN COOLING TOWER SPECIFICATION
AIR PROPERTIES AND
SIZING OF COOLING TOWER HEIGHT
TYPICAL SPECIFICATION FORMAT / DATASHEET
A cooling tower is a heat rejection device which extracts waste heat to the atmosphere through the cooling of a water stream to a lower temperature.
A cooling tower is a heat rejection device which extracts waste heat to the atmosphere through the cooling of a water stream to a lower temperature. Cooling towers may either use the evaporation of water to remove process heat and cool the working fluid to near the wet-bulb air temperature or, in the case of closed circuit dry cooling towers, rely solely on air to cool the working fluid to near the dry-bulb air temperature.
Common applications include cooling the circulating water used in oil refineries, petrochemical and other chemical plants, thermal power stations and HVAC systems for cooling buildings. The classification is based on the type of air induction into the tower: the main types of cooling towers are natural draft and induced draft cooling towers.
Cooling towers vary in size from small roof-top units to very large hyperboloid structures (as in the adjacent image) that can be up to 200 metres (660 ft) tall and 100 metres (330 ft) in diameter, or rectangular structures that can be over 40 metres (130 ft) tall and 80 metres (260 ft) long. The hyperboloid cooling towers are often associated with nuclear power plants,[1] although they are also used to some extent in some large chemical and other industrial plants. Although these large towers are very prominent, the vast majority of cooling towers are much smaller, including many units installed on or near buildings to discharge heat from air conditioning.
Final report on spent solution in hydroprateekj765
Assessment of cooling towers, cooling tower efficiency, assessment of cooling towers fans, material required, maintenance operations, calculation of flow rate of spent
Air Cooled condensers were first introduced in US
power industry in early 1970’s, but only during last 10-15
years number of installations greatly increased largely due to
growing attention being paid to environmental safety. Also,
growing demand for water for both domestic and industrial
use has brought an increased interest in use of Air Cooled
condensers. This is a review paper which studies the
performance of Air-cooled condenser under various operating
conditions it is found that there is degradation in performance
of air cooled condenser under high ambient temperatures and
windy conditions. The heat rejection rate of ACC also depends
on surface condition of fins and thus its performance is
reduced due to external fouling of finned tubes due to weather
conditions and by internal fouling from condensate (Ammonia
corrosion). A Hybrid (dry/wet) dephlegmator achieves major
enhancement in performance when ambient temperatures are
high. Also shading of condensers is done for air-conditioning
units to mitigate the adverse effect of high ambient
temperatures due to solar radiation. Now a day’s wind walls
are used to reduce the effect of high wind velocity .second
option is to increase the fan speed Fin cleaning plays an
important role in heat rejection. External cleaning improves
air side heat transfer coefficient. In order to improve the
performance of an ACC Flat tubes inclined at some angle to
horizontal can also be used in place of conventional circular
horizontal tubes so that an improvement in heat transfer rate
occurs.
Fabrication of Semi-Automatic Molten Metal Pouring System in Casting Industries.IJERA Editor
In India there are many foundry have followed conventional and manual operations. Today’s competitive
environment has lower manufacturing cost, more productivity in less time, high quality product, defect free
operation are required to follow to every foundry man. Mould shifting, Crushing, Lower Surface finish,
Shrinkage, Porosity, Cold shut and Extra material are common casting defects due to these manual operations.
These defects directly affect on productivity, profitability and quality level of organization. In the current global
competitive environment there is a need for the casting units and foundries to develop the components in short
lead time. Defect free castings with minimum production cost have become the need of foundry. In any casting
industry the leading problem taking place is Mould shifting from electrical furnace to the die casting. In the
present work an attempt was made to fabricate the pneumatic system for pouring the molten metal in to the
cavity semi automatically. The system was tested for carrying the metal which reduces the manual work for
mould shifting from electrical furnace to die casting and the results are compared with manual working which
improves the quality, productivity and defect free product
Honest Reviews of Tim Han LMA Course Program.pptxtimhan337
Personal development courses are widely available today, with each one promising life-changing outcomes. Tim Han’s Life Mastery Achievers (LMA) Course has drawn a lot of interest. In addition to offering my frank assessment of Success Insider’s LMA Course, this piece examines the course’s effects via a variety of Tim Han LMA course reviews and Success Insider comments.
Embracing GenAI - A Strategic ImperativePeter Windle
Artificial Intelligence (AI) technologies such as Generative AI, Image Generators and Large Language Models have had a dramatic impact on teaching, learning and assessment over the past 18 months. The most immediate threat AI posed was to Academic Integrity with Higher Education Institutes (HEIs) focusing their efforts on combating the use of GenAI in assessment. Guidelines were developed for staff and students, policies put in place too. Innovative educators have forged paths in the use of Generative AI for teaching, learning and assessments leading to pockets of transformation springing up across HEIs, often with little or no top-down guidance, support or direction.
This Gasta posits a strategic approach to integrating AI into HEIs to prepare staff, students and the curriculum for an evolving world and workplace. We will highlight the advantages of working with these technologies beyond the realm of teaching, learning and assessment by considering prompt engineering skills, industry impact, curriculum changes, and the need for staff upskilling. In contrast, not engaging strategically with Generative AI poses risks, including falling behind peers, missed opportunities and failing to ensure our graduates remain employable. The rapid evolution of AI technologies necessitates a proactive and strategic approach if we are to remain relevant.
How to Make a Field invisible in Odoo 17Celine George
It is possible to hide or invisible some fields in odoo. Commonly using “invisible” attribute in the field definition to invisible the fields. This slide will show how to make a field invisible in odoo 17.
Unit 8 - Information and Communication Technology (Paper I).pdfThiyagu K
This slides describes the basic concepts of ICT, basics of Email, Emerging Technology and Digital Initiatives in Education. This presentations aligns with the UGC Paper I syllabus.
June 3, 2024 Anti-Semitism Letter Sent to MIT President Kornbluth and MIT Cor...Levi Shapiro
Letter from the Congress of the United States regarding Anti-Semitism sent June 3rd to MIT President Sally Kornbluth, MIT Corp Chair, Mark Gorenberg
Dear Dr. Kornbluth and Mr. Gorenberg,
The US House of Representatives is deeply concerned by ongoing and pervasive acts of antisemitic
harassment and intimidation at the Massachusetts Institute of Technology (MIT). Failing to act decisively to ensure a safe learning environment for all students would be a grave dereliction of your responsibilities as President of MIT and Chair of the MIT Corporation.
This Congress will not stand idly by and allow an environment hostile to Jewish students to persist. The House believes that your institution is in violation of Title VI of the Civil Rights Act, and the inability or
unwillingness to rectify this violation through action requires accountability.
Postsecondary education is a unique opportunity for students to learn and have their ideas and beliefs challenged. However, universities receiving hundreds of millions of federal funds annually have denied
students that opportunity and have been hijacked to become venues for the promotion of terrorism, antisemitic harassment and intimidation, unlawful encampments, and in some cases, assaults and riots.
The House of Representatives will not countenance the use of federal funds to indoctrinate students into hateful, antisemitic, anti-American supporters of terrorism. Investigations into campus antisemitism by the Committee on Education and the Workforce and the Committee on Ways and Means have been expanded into a Congress-wide probe across all relevant jurisdictions to address this national crisis. The undersigned Committees will conduct oversight into the use of federal funds at MIT and its learning environment under authorities granted to each Committee.
• The Committee on Education and the Workforce has been investigating your institution since December 7, 2023. The Committee has broad jurisdiction over postsecondary education, including its compliance with Title VI of the Civil Rights Act, campus safety concerns over disruptions to the learning environment, and the awarding of federal student aid under the Higher Education Act.
• The Committee on Oversight and Accountability is investigating the sources of funding and other support flowing to groups espousing pro-Hamas propaganda and engaged in antisemitic harassment and intimidation of students. The Committee on Oversight and Accountability is the principal oversight committee of the US House of Representatives and has broad authority to investigate “any matter” at “any time” under House Rule X.
• The Committee on Ways and Means has been investigating several universities since November 15, 2023, when the Committee held a hearing entitled From Ivory Towers to Dark Corners: Investigating the Nexus Between Antisemitism, Tax-Exempt Universities, and Terror Financing. The Committee followed the hearing with letters to those institutions on January 10, 202
Introduction to AI for Nonprofits with Tapp NetworkTechSoup
Dive into the world of AI! Experts Jon Hill and Tareq Monaur will guide you through AI's role in enhancing nonprofit websites and basic marketing strategies, making it easy to understand and apply.
The Roman Empire A Historical Colossus.pdfkaushalkr1407
The Roman Empire, a vast and enduring power, stands as one of history's most remarkable civilizations, leaving an indelible imprint on the world. It emerged from the Roman Republic, transitioning into an imperial powerhouse under the leadership of Augustus Caesar in 27 BCE. This transformation marked the beginning of an era defined by unprecedented territorial expansion, architectural marvels, and profound cultural influence.
The empire's roots lie in the city of Rome, founded, according to legend, by Romulus in 753 BCE. Over centuries, Rome evolved from a small settlement to a formidable republic, characterized by a complex political system with elected officials and checks on power. However, internal strife, class conflicts, and military ambitions paved the way for the end of the Republic. Julius Caesar’s dictatorship and subsequent assassination in 44 BCE created a power vacuum, leading to a civil war. Octavian, later Augustus, emerged victorious, heralding the Roman Empire’s birth.
Under Augustus, the empire experienced the Pax Romana, a 200-year period of relative peace and stability. Augustus reformed the military, established efficient administrative systems, and initiated grand construction projects. The empire's borders expanded, encompassing territories from Britain to Egypt and from Spain to the Euphrates. Roman legions, renowned for their discipline and engineering prowess, secured and maintained these vast territories, building roads, fortifications, and cities that facilitated control and integration.
The Roman Empire’s society was hierarchical, with a rigid class system. At the top were the patricians, wealthy elites who held significant political power. Below them were the plebeians, free citizens with limited political influence, and the vast numbers of slaves who formed the backbone of the economy. The family unit was central, governed by the paterfamilias, the male head who held absolute authority.
Culturally, the Romans were eclectic, absorbing and adapting elements from the civilizations they encountered, particularly the Greeks. Roman art, literature, and philosophy reflected this synthesis, creating a rich cultural tapestry. Latin, the Roman language, became the lingua franca of the Western world, influencing numerous modern languages.
Roman architecture and engineering achievements were monumental. They perfected the arch, vault, and dome, constructing enduring structures like the Colosseum, Pantheon, and aqueducts. These engineering marvels not only showcased Roman ingenuity but also served practical purposes, from public entertainment to water supply.
A Strategic Approach: GenAI in EducationPeter Windle
Artificial Intelligence (AI) technologies such as Generative AI, Image Generators and Large Language Models have had a dramatic impact on teaching, learning and assessment over the past 18 months. The most immediate threat AI posed was to Academic Integrity with Higher Education Institutes (HEIs) focusing their efforts on combating the use of GenAI in assessment. Guidelines were developed for staff and students, policies put in place too. Innovative educators have forged paths in the use of Generative AI for teaching, learning and assessments leading to pockets of transformation springing up across HEIs, often with little or no top-down guidance, support or direction.
This Gasta posits a strategic approach to integrating AI into HEIs to prepare staff, students and the curriculum for an evolving world and workplace. We will highlight the advantages of working with these technologies beyond the realm of teaching, learning and assessment by considering prompt engineering skills, industry impact, curriculum changes, and the need for staff upskilling. In contrast, not engaging strategically with Generative AI poses risks, including falling behind peers, missed opportunities and failing to ensure our graduates remain employable. The rapid evolution of AI technologies necessitates a proactive and strategic approach if we are to remain relevant.
Read| The latest issue of The Challenger is here! We are thrilled to announce that our school paper has qualified for the NATIONAL SCHOOLS PRESS CONFERENCE (NSPC) 2024. Thank you for your unwavering support and trust. Dive into the stories that made us stand out!
Operation “Blue Star” is the only event in the history of Independent India where the state went into war with its own people. Even after about 40 years it is not clear if it was culmination of states anger over people of the region, a political game of power or start of dictatorial chapter in the democratic setup.
The people of Punjab felt alienated from main stream due to denial of their just demands during a long democratic struggle since independence. As it happen all over the word, it led to militant struggle with great loss of lives of military, police and civilian personnel. Killing of Indira Gandhi and massacre of innocent Sikhs in Delhi and other India cities was also associated with this movement.
Biological screening of herbal drugs: Introduction and Need for
Phyto-Pharmacological Screening, New Strategies for evaluating
Natural Products, In vitro evaluation techniques for Antioxidants, Antimicrobial and Anticancer drugs. In vivo evaluation techniques
for Anti-inflammatory, Antiulcer, Anticancer, Wound healing, Antidiabetic, Hepatoprotective, Cardio protective, Diuretics and
Antifertility, Toxicity studies as per OECD guidelines
"Protectable subject matters, Protection in biotechnology, Protection of othe...
Project report study of cooling tower
1. FINALYEAR PROJECT REPORT ON
STUDY OF COOLING TOWER
A DISSERTATION
Submitted By
SAURABH CHANDRAADHIKARI2K15/CEME/80
MANISH CHAUHAN 2K15/CEME/66
YOGINDER KUMAR 2K15/CEME/90
SUNIL KUMAR DISWAR 2K15/CEME/83
AMIT KUMAR SHARMA 2K15/CEME/53
In fulfillment for the award of the degree of
BACHELOR OF TECHNOLOGY
In
Mechanical Engineering
UNDER THE SUPERVISION OF
ROOP LAL, ASOCIATE PROF.
DEPARTMENT OF MECHANICAL ENGINEERING
DELHI TECHNOLOGICAL UNIVERSITY
(FORMERLY DELHI COLLEGE OF ENGINEERING)
2018
ACKNOWLEDGEMENT
2. Final year project is an indispensable part of any engineering curriculum. It
provides the students with an opportunity to gain experience on the practical
application of their technical knowledge.
We express our gratitude to Mr. ROOP LAL, Associate Professor,
Department of Mechanical Engineering, Delhi Technological University, for
giving us an opportunity to work on such a practical project under his
guidance. He confidently guided and helped us throughout the project.
Words cannot express the support and motivation given by him.
With best regards
SAURABH CHANDRAADHIKARI 2K15/CEME/80
MANISH CHAUHAN 2K15/CEME/66
YOGINDER KUMAR 2K15/CEME/90
SUNIL KUMAR DISWAR 2K15/CEME/83
AMIT KUMAR SHARMA 2K15/CEME/53
CERTIFICATE
3. DELHI TECHNOLOGICAL UNIVERSITY
(FORMERLY DELHI COLLEGE OF ENGINEERING)
Bawana Road, Delhi – 110042
Date:
This is to certify that the final year project report on titled, “STUDY OF COOLING
TOWER” of preliminary stage has been successfully submitted by the following
students for completion of project in next semester for getting award of Bachelor of
Technology, Mechanical Engineering.
SAURABH CHANDRAADHIKARI 2K15/CEME/80
MANISH CHAUHAN 2K15/CEME/66
YOGINDER KUMAR 2K15/CEME/90
SUNILKUMAR DISWAR 2K15/CEME/83
AMIT KUMAR SHARMA 2K15/CEME/53
Roop Lal
Associate Professor
Department Of Mechanical Engineering
Delhi Technological University
CANDIDATES DECLARATION
4. We , Saurabh Chandra Adhikari, Manish Chauhan, Yoginder Kumar, Sunil
Kumar Diswar and Amit Kumar Sharma students of Mechanical Engineering
VIIth
(E) hereby declare that the report on which work will be done on next semester is
being presented in the dissertation entitled "STUDY OF COOLING TOWER” in
partial fulfillment of the requirement for the award of degree in Mechanical
Engineering submitted in Delhi Technological University (Formerly Delhi College Of
Engineering) Bawana Road, Delhi is an authentic record of our “Study of Cooling
Tower” carried out under the guidance of Mr. Roop Lal, Associate Professor of
Mechanical Engineering Department.
SAURABH CHANDRAADHIKARI MANISH CHAUHAN
(2K15/CEME/80) (2K15/CEME/66)
YOGINDER KUMAR
(2K15/CEME/90)
SUNILKUMAR DISWAR AMIT KUMAR SHARMA
(2K15/CEME/83) (2K15/CEME/53)
Contents
Page
Abstract iv
5. List of figures v
List of tables vi
Aim of the work vii
1. Introduction. 1
1.1. What's a cooling tower? 1
1.2. Components of a cooling tower. 2
1.3. Tower materials. 3
2. Types of cooling towers. 4
2.1. Natural draft cooling tower. 4
2.2. Mechanical draft cooling tower. 5
3. Assessment of cooling tower. 7
4. Energy efficiency opportunities. 9
4.1. Selecting the right cooling towers. 9
4.1.1.Capacity. 9
4.1.2.Range. 9
4.1.3.Approach. 9
4.1.4.Heat load. 10
4.1.5.Wet bulb temperature. 10
4.1.6.Relationship between range, flow and heat load. 11
4.1.7.Relationship between approach and wet bulb temperature.11
4.2. Fill media effect. 11
4.3. Pumps and water distribution. 12
4.3.1.Pumps. 12
4.3.2.Optimize cooling water treatment. 12
4.3.3.Install drift eliminators. 12
4.4. Cooling tower fans. 12
6. 5. Option checklist. 13
6. Work sheet. 14
7. Conclusion. 16
8. References. 17
Abstract:
This topic will cover one of the equipments used in cooling process. Cooling tower
which used to reduce the water temperature by extracting the water heat in a simple
way and consists of some basic components to give a high efficiency of the cooling
tower work.
There are some materials at which the cooling tower made of. Sometimes the cold-
water basin was made of concrete. Today, manufacturers use a variety of materials to
construct cooling towers.
This topic is also going to talk about cooling towers types … the 1st
one the natural draft
which makes good benefits from the temperature difference between the ambient air
and the hotter air inside the tower.
On the other hand there is a mechanical draft cooling tower which have a large fans to
force air and the cooling rate in it depend on some parameters '' fan diameter , speed of
operation …. '' .
And there are three types of mechanical towers as listed in table (1) and in figure (4, 5,
and 6).
On the assessment part we will learn how to evaluate the cooling towers work shown
below in figure (7). And there are several ways to measure the performance of cooling
towers.
To increase the energy efficiency of the cooling tower there are some basic things must
be included in the energy conservation like:
Selecting the right cooling tower.
7. The effect of fills.
Pumps and water distribution system.
Fans and motors.
There is the most important part in the report which contains a list to improve the
efficiency of cooling towers work in option check list.
List of Figures
Page
Figure 1: Schematic diagram of a cooling water system. 1
Figure 2: Counter flow natural draft cooling tower. 4
Figure 3: Cross flow natural draft cooling tower. 4
Figure 4: Forced Draft Cooling Tower. 5
Figure 5: Induced draft counter flow cooling tower. 6
Figure 6: Induced draft cross flow cooling tower. 6
Figure 7: Range and approach of cooling towers. 7
iv
8. List of Tables
Page
Table 1: Main features of different types of draft cooling towers. 5
Table 2: Design Values of Different Types of Fill. 12 Table
3: (Worksheet 1) Key Technical Specification. 14 Table
4: (Worksheet 2) Cooling Tower Performance. 15
v
9. 1. INTRODUCTION
This section briefly describes the main features of cooling towers.
1.1 What is a cooling tower?
Cooled water is needed for, for example, air conditioners, manufacturing processes or power generation. A
cooling tower is equipment used to reduce the temperature of a water stream by extracting heat from water
and emitting it to the atmosphere. Cooling towers make use of evaporation whereby some of the water
is evaporated into a moving air stream and subsequently discharged into the atmosphere. As a result, the
remainder of the water is cooled down significantly (Figure 1). Cooling towers are able to lower the water
temperatures more than devices that use only air to reject heat, like the radiator in a car, and are therefore
more cost-effective and energy efficient.
Figure 1. Schematic diagram of a cooling water system
1 1
vi
vii
2
2
1
2
10. 1.2
Components
of a cooling
tower
The basic
components of
a cooling tower
include the
frame and
casing, fill,
cold-water
basin, drift
eliminators, air
inlet, louvers,
nozzles and
fans. These are
described
below.
Frame and
casing. Most
towers have
structural
frames that
support the
exterior
enclosures
(casings),
motors, fans,
and other
components.
With some
smaller
designs, such
as some glass
fiber units, the
casing may
essentially be
the frame.
Fill. Most
towers employ
fills (made of
plastic or
wood) to
facilitate heat
transfer by
maximizing
water and air
contact. There
11. are two types of
fill:
* Splash fill:
waterfalls
over
successive
layers of
horizontal
splash bars,
continuousl
y
breaking
into smaller
droplets,
while also
wetting the
fill surface.
Plastic
splash fills
promote
better heat
transfer than
wood splash
fills.
* Film fill:
consists of
thin, closely
spaced
plastic
surfaces
over which
the water
spreads,
forming a
thin film in
contact
with the
air. These
surfaces
may be
flat,
corrugated,
honeycomb
ed, or other
patterns.
The film
type of fill
is the more
efficient
and
provides
same heat
12. transfer in a
smaller
volume than
the splash
fill.
Cold-water
basin. The cold-
water basin is
located at or
near the bottom
of the tower,
and it receives
the cooled water
that flows down
through the
tower and fills.
The basin
usually has a
sump or low
point for the
cold-water
discharge
connection. In
many tower
designs, the
cold-water
basin is beneath
the entire fill. In
some forced
draft counter
flow design,
however, the
water at the
bottom of the
fill is channeled
to a perimeter
trough that
functions as the
cold-water
basin. Propeller
fans are
mounted
beneath the fill
to blow the air
up through the
tower. With this
design, the
tower is
mounted on
legs, providing
easy access to
the fans and
13. their motors.
Drift
eliminators.
These capture
water droplets
entrapped in
the air stream
that otherwise
would be lost to
the atmosphere.
Air inlet. This
is the point of
entry for the air
entering a
tower. The inlet
may take up an
entire side of a
tower (cross-
flow design) or
be located low
on the side or
the bottom of
the tower
(counter-flow
design).
Louvers.
Generally,
cross-flow
towers have
inlet louvers.
The purpose of
louvers is to
equalize air
flow into the fill
and retain the
water within the
tower. Many
counter flow
tower designs
do not require
louvers.
Nozzles. These
spray water to
wet the fill.
Uniform water
distribution at
the top of the
fill is essential
to achieve
14. proper wetting
of the entire fill
surface.
Nozzles can
either be fixed
and spray in a
round or square
patterns, or
they can be
part of a
rotating
assembly as
found in some
circular cross-
section towers.
Fans. Both
axial (propeller
type) and
centrifugal fans
are used in
towers.
Generally,
propeller fans
are used in
induced draft
towers and both
propeller and
centrifugal fans
are found in
forced draft
towers.
Depending
upon their size,
the type of
propeller fans
used is either
fixed or
variable pitch.
A fan with non-
automatic
adjustable pitch
blades can be
used over a
wide kW range
because the fan
can be adjusted
to deliver the
desired air flow
at the lowest
power
consumption.
15. Automatic
variable pitch
blades can vary
air flow in
response to
changing load
conditions.
1.3 Tower
materials
Originally,
cooling towers
were
constructed
primarily with
wood,
including the
frame, casing,
louvers, fill and
cold-water
basin.
Sometimes the
cold-water
basin was made
of concrete.
Today,
manufacturers
use a variety of
materials to
construct
cooling towers.
Materials are
chosen to
enhance
corrosion
resistance,
reduce
maintenance,
and promote
reliability and
long service
life. Galvanized
steel, various
grades of
stainless steel,
glass fiber, and
concrete are
2
16. widely used in
tower
construction, as
well as
aluminum and
plastics for
some
components.
Frame and
casing. Wooden
towers are still
available, but
many
components are
made of
different
materials, such
as the casing
around the
wooden
framework of
glass fiber, the
inlet air louvers
of glass fiber,
the fill of
plastic and the
cold-water
basin of steel.
Many towers
(casings and
basins) are
constructed of
galvanized steel
or, where a
corrosive
atmosphere is a
problem, the
tower and/or the
basis are made
of stainless
steel. Larger
towers
sometimes are
made of
concrete. Glass
fiber is also
widely used for
cooling tower
casings and
basins, because
they extend the
life of the
17. cooling tower
and provide
protection
against harmful
chemicals.
Fill. Plastics
are widely used
for fill,
including PVC,
polypropylene,
and other
polymers.
When water
conditions
require the use
of splash fill,
treated wood
splash fill is still
used in wooden
towers, but
plastic splash
fill is also
widely used.
Because of
greater heat
transfer
efficiency, film
fill is chosen for
applications
where the
circulating
water is
generally free of
debris that
could block the
fill
passageways.
Nozzles.
Plastics are
also widely
used for
nozzles.
Many
nozzles are
made of
PVC, ABS,
polypropyl
ene, and
glass-filled
nylon.
Fans.
18. Aluminum,
glass fiber and
hot-dipped
galvanized
steel are
commonly used
fan materials.
Centrifugal fans
are often
fabricated from
galvanized steel.
Propeller fans
are made from
galvanized steel,
aluminum, or
molded glass
fiber reinforced
plastic.
2. TYPES
OF
COOLING
TOWERS
This
section
describ
es the
two
main
3
20. tower
(becaus
e hot
air
rises),
fresh
cool air
is
drawn
into the
tower
through
an air
inlet at
the
bottom.
Due to
the
layout
of the
tower,
no fan
is
require
d and
there is
almost
no
circulat
ion of
hot air
that
could
affect
the
perform
ance.
Concret
e is
used for
the
tower
shell
with a
height
of up to
200 m.
These
cooling
towers
are
mostly
only
22. and
the fill
is
located
outside
the
tower.
* Counte
r flow
tower
(Figur
e 3):
air is
drawn
up
throug
h the
falling
water
and
the fill
is
therefo
re
located
inside
the
tower,
althou
gh
design
depend
s on
specifi
c site
conditi
ons.
2.2
4
23. Mechanical
draft cooling
tower
Mechanical
draft towers
have large fans
to force or draw
air through
circulated
water. The
water falls
downwards over
fill surfaces,
which help
increase the
contact time
between the
water and the
air - this helps
maximize heat
transfer
between the
two. Cooling
rates of
mechanical
draft towers
depend upon
various
parameters such
as fan diameter
and speed of
operation, fills
for system
resistance etc.
Mechanical
draft towers are
available in a
large range of
capacities.
Towers can be
either factory
built or field
erected - for
example
concrete towers
are only field
erected. Many
towers are
constructed so
that they can be
grouped
together to
achieve the
desired
24. capacity. Thus,
many cooling
towers are
assemblies of
two or more
individual
cooling towers
or "cells." The
number of cells
they have, e.g.,
a eight-cell
tower, often
refers to such
towers.
Multiple-cell
towers can be
lineal, square,
or round
depending
upon the shape
of the
individual cells
and whether the
air inlets are
located on the
sides or bottoms
of the cells. The
three types of
mechanical
draft towers are
summarized in
(Table 1).
Table 1: Main
features of
different types
of draft cooling
towers (based
on AIRAH)
Type of cooling tower
Forced draft cooling tower (Figure 4
blown through the tower by a fan lo
the air inlet
Induced draft cross flow cooling tow
(Figure 5): ■ water enters at top and
over fill
■ air enters on one side (single-flow
or opposite sides (double-flow towe
■ an induced draft fan draws air acr
towards exit at top of tower
Induced draft counter flow cooling t
25. (Figure 6): ■ hot water enters at the
top ■ air enters bottom and exits at t
top
■ uses forced and induced draft fan
Figure 4. Forced Draft Cooling
Tower ((GEO4VA))
5
27. 3. ASSESSMENT OF COOLING TOWERS
This section describes how the performance of cooling towers can be assessed.
The performance of cooling towers is evaluated to assess present levels of approach
and range against their design values, identify areas of energy wastage and to suggest
improvements.
During the performance evaluation, portable monitoring instruments are used to
measure the following parameters:
* Wet bulb temperature of air
* Dry bulb temperature of air
* Cooling tower inlet water temperature
* Cooling tower outlet water temperature
* Exhaust air temperature
* Electrical readings of pump and fan motors
* Water flow rate
* Air flow rate
Hot Water Temperature (In)
Range (In) to the Tower (Out) from the Tower
Cold-water Temperature (Out)
Approach
Wet Bulb Temperature (Ambient)
Figure 7. Range and approach of cooling towers
These measured parameters and then used to determine the cooling tower
performance in several ways. (Note: CT = cooling tower; CW = cooling water). These
are:
a) Range (see Figure 7). This is the difference between the cooling tower water inlet
and outlet temperature. A high CT Range means that the cooling tower has been
able to reduce the water temperature effectively, and is thus performing well. The
formula is:
CT Range (°C) = [CW inlet temp (°C) - CW outlet temp (°C)]
7
28. b) Approach (see Figure 7). This is the difference between
the cooling tower outlet cold-
water temperature and ambient wet bulb temperature. The
lower the approach the better
the cooling tower performance. Although, both range and
approach should be monitored,
the ' Approach' is a better indicator of cooling tower
performance.
CT Approach (°C) = [CW outlet temp (°C) - Wet bulb temp
(°C)]
c) Effectiveness. This is the ratio between the range and the
ideal range (in percentage), i.e.
difference between cooling water inlet temperature and
ambient wet bulb temperature, or
in other words it is = Range / (Range + Approach). The
higher this ratio, the higher the
cooling tower effectiveness.
CT Effectiveness (%) = 100 x (CW temp - CW out temp) /
(CW in temp - WB temp)
d) Cooling capacity. This is the heat rejected in kCal/hr or
TR, given as product of mass
flow rate of water, specific heat and temperature
difference.
e) Evaporation loss. This is the water quantity evaporated
for cooling duty. Theoretically
the evaporation quantity works out to 1.8 m3 for every
1,000,000 kCal heat rejected. The
following formula can be used (Perry):
Evaporation loss (m3
/hr) = 0.00085 x 1.8 x
circulation rate (m3
/hr) x (T1-T2) T1 - T2 =
temperature difference between inlet and
outlet water
f) Cycles of concentration (C.O.C). This is the ratio of
dissolved solids in circulating water
to the dissolved solids in makeup water.
g) Blow down losses depend upon cycles of concentration
and the evaporation losses and is
given by formula:
Blow down = Evaporation loss / (C.O.C. - 1)
h) h) Liquid/Gas (L/G) ratio. The L/G ratio of a cooling
tower is the ratio between the water and the air mass flow
29. rates. Cooling towers have certain design values, but
seasonal variations require adjustment and tuning of
water and air flow rates to get the best cooling tower
effectiveness. Adjustments can be made by water box
loading changes or blade angle adjustments.
Thermodynamic rules also dictate that the heat removed
from the water must be equal to the heat absorbed by the
surrounding air. Therefore the following formulae can be
used:
i) L (T1 - T2) = G (h2 - h1) L/G = (h2 - h1) / (T1 - T2)
Where:
L/G = liquid to gas mass flow ratio (kg/kg)
T1 = hot water temperature (°C)
T2 = cold-water temperature (°C) h2 = enthalpy
of air-water vapor mixture at exhaust wet-bulb
temperature (same units as above)
h1 = enthalpy of air-water vapor mixture at
inlet wet-bulb temperature (same units as
above).
4. ENERGY EFFICIENCY OPPORTUNITIES
This section includes main areas for improving energy
efficiency of cooling towers. The main areas for energy
conservation include:
* Selecting the right cooling tower (because the
structural aspects of the cooling tower
cannot be changed after it is installed)
* Fills
* Pumps and water distribution system
* Fans and motors
4.1 Selecting the right cooling towers
Once a cooling tower is in place it is very difficult to
significantly improve its energy performance. A number of
factors are of influence on the cooling tower's performance
and should be considered when choosing a cooling tower:
capacity, range, approach, heat load, wet bulb temperature,
and the relationship between these factors. This is described
below.
4.1.1 Capacity
8
30. Heat dissipation (in kCal/hour) and circulated flow rate
(m3
/hr) are an indication of the capacity of cooling towers.
However, these design parameters are not sufficient to
understand the cooling tower performance. For example, a
cooling tower sized to cool 4540 m3
/hr through a 13.9 °C
range might be larger than a cooling tower to cool 4540 m3
/hr
through 19.5 °C range. Therefore other design parameters are
also needed.
4.1.2 Range
Range is determined not by the cooling tower, but by the
process it is serving. The range at the exchanger is
determined entirely by the heat load and the water
circulation rate through the exchanger and going to the
cooling water. The range is a function of the heat load and the
flow circulated through the system:
Range °C = Heat load (in kCal/hour) / Water
circulation rate (l/hour)
Cooling towers are usually specified to cool a certain flow
rate from one temperature to another temperature at a
certain wet bulb temperature. For example, the cooling tower
might be specified to cool 4540 m3
/hr from 48.9°C to 32.2°C
at 26.7°C wet bulb temperature.
4.1.3 Approach
As a general rule, the closer the approach to the wet bulb,
the more expensive the cooling tower due to increased size.
Usually a 2.8°C approach to the design wet bulb is the
coldest water temperature that cooling tower
manufacturers will guarantee. When the size of the tower
has to be chosen, then the approach is most important,
closely followed by the flow rate, and the range and wet
bulb would be of lesser importance.
Approach (5.5°C) = Cold-water temperature 32.2
°C - Wet bulb temperature (26.7°)
4.1.4 Heat load
9
31. The heat load imposed on a cooling tower is determined by
the process being served. The degree of cooling required is
controlled by the desired operating temperature of the
process. In most cases, a low operating temperature is
desirable to increase process efficiency or to improve the
quality or quantity of the product. However, in some
applications (e.g. internal combustion engines) high
operating temperatures are desirable. The size and cost of
the cooling tower is increases with increasing heat load.
Purchasing undersized equipment (if the calculated heat load
is too low) and oversized equipment (if the calculated heat
load is too high) is something to be aware of.
Process heat loads may vary considerably depending upon
the process involved and are therefore difficult to
determine accurately. On the other hand, air conditioning
and refrigeration heat loads can be determined with greater
accuracy.
Information is available for the heat rejection requirements
of various types of power equipment. A sample list is as
follows (BEE, 2004):
■ Air Compressor
* Single-stage - 129 kCal/kW/hr
* Single-stage
with after cooler
- 862
kCal/kW/hr
Two-stage with
intercooler - 518
kCal/kW/hr
Two-stage with intercooler and after cooler - 862
kCal/kW/hr
* Refrigeration, Compression - 63 kCal/min/TR
* Refrigeration, Absorption - 127 kCal/min/TR
* Steam Turbine Condenser - 555 kCal/kg of steam
* Diesel Engine, Four-Cycle, Supercharged - 880
kCal/kW/hr
* Natural Gas Engine, Four-cycle - 1523 kCal/kW/hr (= 18
kg/cm2
compression)
4.1.5 Wet bulb temperature
Wet bulb temperature is an important factor in performance
of evaporative water cooling equipment, because it is the
lowest temperature to which water can be cooled. For this
reason, the wet bulb temperature of the air entering the
cooling tower determines the minimum operating
temperature level throughout the plant, process, or system.
The following should be considered when pre-selecting a
cooling tower based on the wet bulb temperature:
* Theoretically, a cooling tower will cool water to the
entering wet bulb temperature. In
practice, however, water is cooled to a temperature
32. higher than the wet bulb temperature
because heat needs to be rejected from the cooling tower.
* A pre-selection of towers based on the design wet
bulb temperature must consider
conditions at the tower site. The design wet bulb
temperature also should not be
exceeded for more than 5 percent of the time. In general,
the design temperature selected
is close to the average maximum wet bulb temperature
in summer.
* Confirm whether the wet bulb temperature is specified
as ambient (the temperature in
the cooling tower area) or inlet (the temperature of the
air entering the tower, which is
often affected by discharge vapors recycled into
the tower). As the impact of recirculation cannot
be known in advance, the ambient wet bulb
temperature is preferred.
* Confirm with the supplier if the cooling tower is
able to deal with the effects of
increased wet bulb temperatures.
* The cold-water temperature must be low enough to
exchange heat or to condense vapors
at the optimum temperature level. The quantity and
temperature of heat exchanged can
be considered when choosing the right size cooling
tower and heat exchangers at the
lowest costs.
4.1.6 Relationship between range, flow and heat load
The range increases when the quantity of circulated water and
heat load increase. This means that increasing the range as a
result of added heat load requires a larger tower. There are
two possible causes for the increased range:
* The inlet water temperature is increased (and the
cold-water temperature at the exit
remains the same). In this case it is economical to invest
in removing the additional heat.
* The exit water temperature is decreased (and the hot
water temperature at the inlet
remains the same). In this case the tower size would
have to be increased considerably
because the approach is also reduced, and this is not
always economical.
4.1.7 Relationship between approach and wet bulb
temperature
The design wet bulb temperature is determined by the
geographical location. For a certain approach value (and at a
10
33. constant range and flow range), the higher the wet bulb
temperature, the smaller the tower required. For example, a
4540 m3
/hr cooling tower selected for a 16.67°C range and
a 4.45°C approach to 21.11°C wet bulb would be larger than
the same tower to a 26.67°C wet bulb. The reason is that air
at the higher wet bulb temperature is capable of picking
up more heat. This is explained for the two different wet
bulb temperatures:
* Each kg of air entering the tower at a wet bulb
temperature of 21.1°C contains 18.86
kCal. If the air leaves the tower at 32.2°C wet bulb
temperature, each kg of air contains
24.17 kCal. At an increase of 11.1°C, the air picks up
12.1 kCal per kg of air.
* Each kg of air entering the tower at a wet bulb
temperature of 26.67°C contains 24.17
kCal. If the air leaves at 37.8°C wet bulb temperature,
each kg of air contains 39.67
kCal. At an increase of 11.1°C, the air picks up 15.5
kCal per kg of air, which is much
more than the first scenario.
4.2 Fill media effects
In a cooling tower, hot water is distributed above fill media
and is cooled down through evaporation as it flows down the
tower and gets in contact with air. The fill media impacts
energy consumption in two ways:
* Electricity is used for pumping above the fill and for
fans that create the air draft. An
efficiently designed fill media with appropriate water
distribution, drift eliminator, fan,
gearbox and motor with therefore lead to lower
electricity consumption.
* Heat exchange between air and water is influenced by
surface area of heat exchange,
duration of heat exchange (interaction) and turbulence in
water effecting thoroughness of
intermixing. The fill media determines all of these
and therefore influences the heat
exchange. The greater the heat exchange, the more
effective the cooling tower becomes.
There are three types of fills:
Splash fills media. Splash fill media generates the
required heat exchange area by splashing water over
the fill media into smaller water droplets. The surface
area of the water droplets is the surface area for heat
exchange with the air.
Film fills media. In a film fill, water forms a thin
film on either side of fill sheets. The surface area of the
34. fill sheets is the area for heat exchange with the
surrounding air. Film fill can result in significant
electricity savings due to fewer air and pumping
head requirements.
Low-clog film fills. Low-clog film fills with higher flute
sizes were recently developed to
handle high turbid waters. Low clog film fills are
considered as the best choice for seawater in terms of
power savings and performance compared to
conventional splash type fills.
Table 2: Design Values of Different Types of Fill
Splash fill Film fill Low clog film
Possible L/G ratio 1.1 - 1.5 1.5 - 2.0 1.4 - 1.8
Effective heat exchange area 30 - 45 m2
/m3
150m2
/m3
85 - 100 m2
/m3
Fill height required 5 - 10 m 1.2 - 1.5 m 1.5 - 1.8 m
Pumping head required 9 - 12 m 5 - 8 m 6 - 9 m
Quantity of air required High Lowest Low
4.3 Pumps and water distribution
4.3.1 Pumps
Areas for energy efficiency improvements are discussed in
details in the Pumps and Pumping Systems chapter.
4.3.2 Optimize cooling water treatment
Cooling water treatment (e.g. to control suspended solids,
algae growth) is mandatory for any cooling tower
independent of what fill media is used. With increasing
costs of water, efforts to increase Cycles of Concentration
(COC), by cooling water treatment would help to reduce
make up water requirements significantly. In large
industries and power plants improving the COC is often
considered a key area for water conservation.
4.3.3 Install drift eliminators
It is very difficult to ignore drift problems in cooling
towers. Nowadays most of the end user specifications
assume a 0.02% drift loss.
But thanks to technological developments and the
production of PVC, manufacturers have improved drift
eliminator designs. As a result drift losses can now be as
low as 0.003 -0.001%.
4.4 Cooling tower fans
11
35. The purpose of a cooling tower fan is to move a specified
quantity of air through the system. The fan has to overcome
the system resistance, which is defined as the pressure loss, to
move the air. The fan output or work done by the fan is the
product of air flow and the pressure loss. The fan output and
kW input determines the fan efficiency. The fan efficiency in
turn is greatly dependent on the profile of the blade. Blades
include:
* Metallic blades, which are manufactured by extrusion or
casting processes and therefore
it is difficult to produce ideal aerodynamic profiles
* Fiber reinforced plastic (FRP) blades are normally hand
molded which makes it easier to
produce an optimum aerodynamic profile tailored to
specific duty conditions. Because
FRP fans are light, they need a low starting torque
requiring a lower HP motor, the lives
of the gear box, motor and bearing is increased, and
maintenance is easier.
An 85-92% efficiency can be achieved with blades with an
aerodynamic profile, optimum twist, taper and a high
coefficient of lift to coefficient of drop ratio. However, this
efficiency is drastically affected by factors such as tip
clearance, obstacles to airflow and inlet shape, etc.
5. OPTION CHECKLIST
This section lists the most important options to improve
energy efficiency of cooling towers.
* Follow manufacturer's recommended clearances around
cooling towers and relocate or
modify structures that interfere with the air intake or
exhaust
* Optimize cooling tower fan blade angle on a seasonal
and/or load basis
* Correct excessive and/or uneven fan blade tip clearance
and poor fan balance
* In old counter-flow cooling towers, replace old spray type
nozzles with new square spray
nozzles that do not clog
* Replace splash bars with self-extinguishing PVC cellular
film fill
* Install nozzles that spray in a more uniform water pattern
12
36. * Clean plugged cooling tower distribution nozzles
regularly
* Balance flow to cooling tower hot water basins
* Cover hot water basins to minimize algae growth that
contributes to fouling
* Optimize the blow down flow rate, taking into account
the cycles of concentration (COC)
limit
* Replace slat type drift eliminators with low-pressure
drop, self-extinguishing PVC
cellular units
* Restrict flows through large loads to design values
* Keep the cooling water temperature to a minimum
level by (a) segregating high heat
loads like furnaces, air compressors, DG sets and (b)
isolating cooling towers from
sensitive applications like A/C plants, condensers of
captive power plant etc. Note: A 1°C
cooling water temperature increase may increase the
A/C compressor electricity
consumption by 2.7%. A 1°C drop in cooling water
temperature can give a heat rate
saving of 5 kCal/kWh in a thermal power plant.
* Monitor approach, effectiveness and cooling capacity
to continuously optimize the
cooling tower performance, but consider seasonal
variations and side variations
* Monitor liquid to gas ratio and cooling water flow rates
and amend these depending on
the design values and seasonal variations. For
example: increase water loads during
summer and times when approach is high and increase air
flow during monsoon times and
when approach is low.
* Consider COC improvement measures for water savings
* Consider energy efficient fiber reinforced plastic blade
adoption for fan energy savings
* Control cooling tower fans based on exit water
temperatures especially in small units
* Check cooling water pumps regularly to maximize their
efficiency
37. 6. WORKSHEETS
This section includes following worksheets:
1. Key Technical Specifications
2. Cooling Tower Performance
Table 3 :( Worksheet 1) KEY TECHNICAL SPECIFICATION
No. Parameter Units Cooling tower
reference
CT 1 CT 2
1. Type of cooling tower
2. Number of tower
3. Number of cells per tower
4. Area per cell
5. Water flow m3
/hr
6. Pumping power kW
7. Pumping head m
8. Fan power kW
9. Design hot water temperature °C
10. Design cold-water temperature °C
11. Design wet bulb temperature
°C
13
14
38. Table 4 :( Worksheet 2) COOLING TOWER PERFORMANCE
No. Parameter reference Units Cooling tower (CT)
CT 1 CT 2
1. Dry bulb temperature °C
2. Wet bulb temperature °C
3. CT inlet temperature °C
4. CT outlet temperature °C
5. Range °C
6. Approach °C
7. CT effectiveness %
8. Average water flow kg/hr
9. Average air quantity kg/hr
10. Liquid/gas (L/G) ratio kg water/kg air
11. Evaporation loss m3
/hr
12. CT heat loading kCal/hr
15
39. 7. Conclusion:
First we concerned the meaning of cooling tower and knew each one
how to use it, how it is installed, and from which materials it is
prepared.
Then identified the main two types of cooling tower and recognized
the series of work of each one and its uses.
Then the evaluation of the cooling tower work and how to increase
the energy efficiency opportunities have been discussed.
By an effective list we knew how to check the work of cooling tower.
16
40. 8. REFERENCES
Australian Institute of Air Conditioning Refrigeration and Heating
(AIRAH). Types of Cooling Towers. In: Selecting a Cooling Tower Level
1 - Participant Guide Version 1.0 www.airah.org.au/downloads/CPD-
samplepg.pdf.
National Productivity Council (NPC). NPC Case Studies.
Bureau of Energy Efficiency, Ministry of Power, India. Cooling
Towers. In: Energy Efficiency in Electrical Utilities. Chapter 7, pg
135 - 151. 2004
Perry. Perry's Chemical Engineers Handbook. Page 12-17.
Pacific Northwest National Laboratory, Photo Library. 2001.
www.pnl.gov, www.cce.iastate.edu/courses/ce525/Cooling
%20Towers.doc
Gulf Coast Chemical Commercial Inc. Cooling
Systems. 1995
www.gc3.com/techdb/manual/coolfs.htm
GEO4VA, Virginia Department of Mines, Minerals and Energy. Ground Loop
Configuration and Installation. www. geo4va. VT. edu/A2/A2.htm
Ramarao, R.A. Paltech Cooling Towers and Equipment Ltd. Design of Fills.
Shivaraman, T. Shiriram Towertech Ltd. Selection and Design of
Cooling Towers. www. shiriramtowertech. com
(BEE India, 2004; Ramarao; and Shivaraman)
(Pacific Northwest National Laboratory, 2001)
(Gulf Coast Chemical Commercial Inc, 1995)
17