The document discusses gas-liquid interactions and equilibrium. It explains that when a gas mixture comes into contact with a liquid, some gas components will dissolve into the liquid according to their solubility. This results in an equilibrium concentration in the liquid that depends on temperature and pressure. As an example, it examines the system of ammonia, air, and water, noting that ammonia is very soluble. It describes how an equilibrium is established between the dissolving and escaping of ammonia molecules. The document then introduces equilibrium curves and Henry's law for modeling solubility relationships, noting how various factors like pressure, temperature and gas identity affect solubility.
An Overview to the most common Industrial Mass Transfer Operations & Process Separation Technologies
Course Description
In this course we will cover the most basic processes involved in Mass Transfer Operations. This is an overview of what type of processes, methods and units are used in the industry. This is mostly an introductory course which will allow you to learn, understand and know the approach towards separation processes involving mass transfer phenomena.
It is an excellent course before any Mass Transfer Process or Unit Operation Course such as Distillations, Extractions, Leaching, Membranes, Absorption, etc...
This course is extremely recommended if you will continue with the following:
Flash Distillation, Simple Distillation, Batch Distillation
Gas Absorption, Desorption & Stripping
Binary Distillation, Fractional Distillation
Scrubbers, Gas Treating
Sprayers / Spray Towers
Bubble Columns / Sparged Vessels
Agitation Vessels
Packed Towers, Tray Towers
Membranes
Liquid Extraction
Dryers / Humidifiers
Adsorbers
Evaporators/Sublimators
Crystallizers
Centrifugations
And many other Separation Technology!
At the end of the Course:
You will be able to understand the mass transfer operations concepts. You will be able to identify Mass Transfer Unit Operations. You will be also able to ensure the type of method of separation technology used.
You will be able to apply this theory in further Unit Operations.
Theory-Based Course
This is a very theoretical course, some calculations and exercises are present, but overall, expect mostly theoretical concepts.
An Overview to the most common Industrial Mass Transfer Operations & Process Separation Technologies
Course Description
In this course we will cover the most basic processes involved in Mass Transfer Operations. This is an overview of what type of processes, methods and units are used in the industry. This is mostly an introductory course which will allow you to learn, understand and know the approach towards separation processes involving mass transfer phenomena.
It is an excellent course before any Mass Transfer Process or Unit Operation Course such as Distillations, Extractions, Leaching, Membranes, Absorption, etc...
This course is extremely recommended if you will continue with the following:
Flash Distillation, Simple Distillation, Batch Distillation
Gas Absorption, Desorption & Stripping
Binary Distillation, Fractional Distillation
Scrubbers, Gas Treating
Sprayers / Spray Towers
Bubble Columns / Sparged Vessels
Agitation Vessels
Packed Towers, Tray Towers
Membranes
Liquid Extraction
Dryers / Humidifiers
Adsorbers
Evaporators/Sublimators
Crystallizers
Centrifugations
And many other Separation Technology!
At the end of the Course:
You will be able to understand the mass transfer operations concepts. You will be able to identify Mass Transfer Unit Operations. You will be also able to ensure the type of method of separation technology used.
You will be able to apply this theory in further Unit Operations.
Theory-Based Course
This is a very theoretical course, some calculations and exercises are present, but overall, expect mostly theoretical concepts.
Slides for the eLearning course Separation and purification processes in biorefineries (https://open-learn.xamk.fi) in IMPRESS project.
Section: Distillation
Subject: 1.1 Vapor Liquid Equilibrium
Slides for the eLearning course Separation and purification processes in biorefineries (https://open-learn.xamk.fi) in IMPRESS project (https://www.spire2030.eu/impress).
Section: Mass transfer processes
Subject: 2.4 Interphase mass transfer
COURSE LINK:
https://www.chemicalengineeringguy.com/courses/gas-absorption-stripping/
Introduction:
Gas Absorption is one of the very first Mass Transfer Unit Operations studied in early process engineering. It is very important in several Separation Processes, as it is used extensively in the Chemical industry.
Understanding the concept behind Gas-Gas and Gas-Liquid mass transfer interaction will allow you to understand and model Absorbers, Strippers, Scrubbers, Washers, Bubblers, etc…
We will cover:
- REVIEW: Of Mass Transfer Basics required
- GAS-LIQUID interaction in the molecular level, the two-film theory
- ABSORPTION Theory
- Application of Absorption in the Industry
- Counter-current & Co-current Operation
- Several equipment to carry Gas-Liquid Operations
- Bubble, Spray, Packed and Tray Column equipments
- Solvent Selection
- Design & Operation of Packed Towers
- Pressure drop due to packings
- Solvent Selection
- Design & Operation of Tray Columns
- Single Component Absorption
- Single Component Stripping/Desorption
- Diluted and Concentrated Absorption
- Basics: Multicomponent Absorption
- Software Simulation for Absorption/Stripping Operations (ASPEN PLUS/HYSYS)
----
Please show the love! LIKE, SHARE and SUBSCRIBE!
More likes, sharings, suscribers: MORE VIDEOS!
-----
CONTACT ME
Chemical.Engineering.Guy@Gmail.com
www.ChemicalEngineeringGuy.com
http://facebook.com/Chemical.Engineering.Guy
You speak spanish? Visit my spanish channel -www.youtube.com/ChemEngIQA
An Overview to the most common Industrial Mass Transfer Operations & Process Separation Technologies
Course Description
In this course we will cover the most basic processes involved in Mass Transfer Operations. This is an overview of what type of processes, methods and units are used in the industry. This is mostly an introductory course which will allow you to learn, understand and know the approach towards separation processes involving mass transfer phenomena.
It is an excellent course before any Mass Transfer Process or Unit Operation Course such as Distillations, Extractions, Leaching, Membranes, Absorption, etc...
This course is extremely recommended if you will continue with the following:
Flash Distillation, Simple Distillation, Batch Distillation
Gas Absorption, Desorption & Stripping
Binary Distillation, Fractional Distillation
Scrubbers, Gas Treating
Sprayers / Spray Towers
Bubble Columns / Sparged Vessels
Agitation Vessels
Packed Towers, Tray Towers
Membranes
Liquid Extraction
Dryers / Humidifiers
Adsorbers
Evaporators/Sublimators
Crystallizers
Centrifugations
And many other Separation Technology!
At the end of the Course:
You will be able to understand the mass transfer operations concepts. You will be able to identify Mass Transfer Unit Operations. You will be also able to ensure the type of method of separation technology used.
You will be able to apply this theory in further Unit Operations.
Theory-Based Course
This is a very theoretical course, some calculations and exercises are present, but overall, expect mostly theoretical concepts.
An Overview to the most common Industrial Mass Transfer Operations & Process Separation Technologies
Course Description
In this course we will cover the most basic processes involved in Mass Transfer Operations. This is an overview of what type of processes, methods and units are used in the industry. This is mostly an introductory course which will allow you to learn, understand and know the approach towards separation processes involving mass transfer phenomena.
It is an excellent course before any Mass Transfer Process or Unit Operation Course such as Distillations, Extractions, Leaching, Membranes, Absorption, etc...
This course is extremely recommended if you will continue with the following:
Flash Distillation, Simple Distillation, Batch Distillation
Gas Absorption, Desorption & Stripping
Binary Distillation, Fractional Distillation
Scrubbers, Gas Treating
Sprayers / Spray Towers
Bubble Columns / Sparged Vessels
Agitation Vessels
Packed Towers, Tray Towers
Membranes
Liquid Extraction
Dryers / Humidifiers
Adsorbers
Evaporators/Sublimators
Crystallizers
Centrifugations
And many other Separation Technology!
At the end of the Course:
You will be able to understand the mass transfer operations concepts. You will be able to identify Mass Transfer Unit Operations. You will be also able to ensure the type of method of separation technology used.
You will be able to apply this theory in further Unit Operations.
Theory-Based Course
This is a very theoretical course, some calculations and exercises are present, but overall, expect mostly theoretical concepts.
Slides for the eLearning course Separation and purification processes in biorefineries (https://open-learn.xamk.fi) in IMPRESS project.
Section: Distillation
Subject: 1.1 Vapor Liquid Equilibrium
Slides for the eLearning course Separation and purification processes in biorefineries (https://open-learn.xamk.fi) in IMPRESS project (https://www.spire2030.eu/impress).
Section: Mass transfer processes
Subject: 2.4 Interphase mass transfer
COURSE LINK:
https://www.chemicalengineeringguy.com/courses/gas-absorption-stripping/
Introduction:
Gas Absorption is one of the very first Mass Transfer Unit Operations studied in early process engineering. It is very important in several Separation Processes, as it is used extensively in the Chemical industry.
Understanding the concept behind Gas-Gas and Gas-Liquid mass transfer interaction will allow you to understand and model Absorbers, Strippers, Scrubbers, Washers, Bubblers, etc…
We will cover:
- REVIEW: Of Mass Transfer Basics required
- GAS-LIQUID interaction in the molecular level, the two-film theory
- ABSORPTION Theory
- Application of Absorption in the Industry
- Counter-current & Co-current Operation
- Several equipment to carry Gas-Liquid Operations
- Bubble, Spray, Packed and Tray Column equipments
- Solvent Selection
- Design & Operation of Packed Towers
- Pressure drop due to packings
- Solvent Selection
- Design & Operation of Tray Columns
- Single Component Absorption
- Single Component Stripping/Desorption
- Diluted and Concentrated Absorption
- Basics: Multicomponent Absorption
- Software Simulation for Absorption/Stripping Operations (ASPEN PLUS/HYSYS)
----
Please show the love! LIKE, SHARE and SUBSCRIBE!
More likes, sharings, suscribers: MORE VIDEOS!
-----
CONTACT ME
Chemical.Engineering.Guy@Gmail.com
www.ChemicalEngineeringGuy.com
http://facebook.com/Chemical.Engineering.Guy
You speak spanish? Visit my spanish channel -www.youtube.com/ChemEngIQA
Absorption & indusrial absorber,Gas Absorption,Equipments,Absorption in chemical Reaction,Absorption in Packed Tower,Absorption for counter current,Choice of Solvent,Continuous Contact Equipment,Height Equivalent to Theoretical Plate,HETP
Slides for the eLearning course Separation and purification processes in biorefineries (https://open-learn.xamk.fi) in IMPRESS project (https://www.spire2030.eu/impress).
Section: Mass transfer processes
Subject: 1.3 Rate and equilibrium
Slides for the eLearning course Separation and purification processes in biorefineries (https://open-learn.xamk.fi) in IMPRESS project (https://www.spire2030.eu/impress).
Section: Mass transfer processes
Subject: 2.2 Molecular diffusion
Slides for the eLearning course Separation and purification processes in biorefineries (https://open-learn.xamk.fi) in IMPRESS project (https://www.spire2030.eu/impress).
Section: Mass transfer processes
Subject: 2.1 Overview
Estimation of Pressure Drop in Pipe Systems
0 INTRODUCTION/PURPOSE
1 SCOPE
2 FIELD OF APPLICATION
3 DEFINITIONS
3.1 units
4 SOURCES OF DATA
5 BASIC CONCEPTS
5.1 Equation for Pressure Change in a Flowing
Fluid
5.2 Static and Stagnation Pressures
5.3 Sonic Flow
6 INCOMPRESSIBLE FLOW IN PIPES OF CONSTANT
CROSS-SECTION
6.1 Straight Circular Pipes
6.2 Ducts of Non-circular Cross-section
6.3 Coils
6.4 General Equation for Incompressible Flow
in Pipes of Constant Cross-section
7 COMPRESSIBLE FLOW IN PIPES OF CONSTANT
CROSS-SECTION
7.1 Isothermal Flow
7.2 Adiabatic Flow
7.3 Estimation of Pressure Drop for Adiabatic
Flow in Pipes of Constant Cross-section
7.4 Ratio of Isothermal to Adiabatic Pressure Drop
8 FLOW IN PIPE FITTINGS
8.1 Incompressible Flow
8.2 Compressible Flow
9 FLOW IN BENDS
9.1 Incompressible Flow in Bends
9.2 Compressible Flow in Bends
10 CHANGES IN CROSS-SECTIONAL AREA
9.1 Incompressible Flow
9.2 Compressible Flow
11 ORIFICES, NOZZLES AND VENTURIS
11.1 Incompressible Flow through an Orifice
11.2 Compressible Flow through an Orifice or Nozzle
11.3 Venturi Choke Tubes
12 VALVES
12.1 General
12.2 Incompressible Flow in Valves
12.2 Compressible Flow in Valves
13 COMBINING AND DIVIDING FLOW
9.1 Incompressible Flow
9.2 Compressible Flow
14 COMPUTER PROGRAMS FOR FLUID FLOW
15 NOMENCLATURE
16 REFERENCES
APPENDICES
A BASIC THERMODYNAMICS
B COMPRESSIBLE FLOW THROUGH ORIFICES
C THE ‘TWO-K’ METHOD FOR FITTING PRESSURE LOSS
Agitation and Mixing are two important unit operations used in industries such as Impellers agitators are widely used to circulate the liquid through the vessel in which the dispersion of liquids and gases into other liquids like mixing of stiff paste, elastomers and dry solids powders takes place.
COURSE LINK:
https://www.chemicalengineeringguy.com/courses/gas-absorption-stripping/
Introduction:
Gas Absorption is one of the very first Mass Transfer Unit Operations studied in early process engineering. It is very important in several Separation Processes, as it is used extensively in the Chemical industry.
Understanding the concept behind Gas-Gas and Gas-Liquid mass transfer interaction will allow you to understand and model Absorbers, Strippers, Scrubbers, Washers, Bubblers, etc…
We will cover:
- REVIEW: Of Mass Transfer Basics required
- GAS-LIQUID interaction in the molecular level, the two-film theory
- ABSORPTION Theory
- Application of Absorption in the Industry
- Counter-current & Co-current Operation
- Several equipment to carry Gas-Liquid Operations
- Bubble, Spray, Packed and Tray Column equipments
- Solvent Selection
- Design & Operation of Packed Towers
- Pressure drop due to packings
- Solvent Selection
- Design & Operation of Tray Columns
- Single Component Absorption
- Single Component Stripping/Desorption
- Diluted and Concentrated Absorption
- Basics: Multicomponent Absorption
- Software Simulation for Absorption/Stripping Operations (ASPEN PLUS/HYSYS)
----
Please show the love! LIKE, SHARE and SUBSCRIBE!
More likes, sharings, suscribers: MORE VIDEOS!
-----
CONTACT ME
Chemical.Engineering.Guy@Gmail.com
www.ChemicalEngineeringGuy.com
http://facebook.com/Chemical.Engineering.Guy
You speak spanish? Visit my spanish channel -www.youtube.com/ChemEngIQA
The Principles required to understand Distillation, Absorption, Stripping, Flashing, Gas Treating, Scrubbing and more!
Introduction:
This course covers all the theory required to understand the basic principles behind Unit Operations that are based on Mass Transfer. Most of these Unit Operations (Equipments) are used in Process Separation Technologies in the Industry.Common examples are Distillation, Absorption and Scrubbing.
This course is required for the following:
Flash Distillation
Gas Absorption & Stripping
Simple Distillation
Batch Distillation
Binary Distillation
Fractional Distillation
Scrubbers
Gas Treating
Sprayers / Spray Towers
Bubble Columns / Sparged Vessels
Agitation Vessels
Packed Towers
Tray Towers
We will cover:
Mass Transfer Basics
Diffusion, Convection
Flux & Fick's Law
The Concept of Equilibrium & Phases
Gibbs Phase Rule
Vapor Pressure
Equilibrium Vapor-Liquid Diagrams (T-xy, P-xy, XY)
Equilibrium Curves
Dew Point, Bubble Point
Volatility (Absolute & Relative)
K-Values
Ideal Cases vs. Real Cases
Henry's Law
Raoult's Law
Deviations of Ideal Cases (Positive and Negative)
Azeotropes
Solubility of Gases in Liquids
Interphase Mass Transfer and its Theories
Two Film Theory
Mass Transfer Coefficients (Overall vs Local)
Getting Vapor-Liquid and Solubility Data
Solved-Problem Approach:
All theory is backed with:
Exercises
Solved problems
Proposed problems
Homework
Case Studies
Individual Study
At the end of the course:
You will be able to understand the mass transfer concepts behind various Unit Operations involving Vapor - Liquid Interaction.
You will be able to apply this theory in further Unit Operations related to Mass Transfer Vapor - Liquid, which is one of the most common interactions found in the industry.
About your instructor:
I majored in Chemical Engineering with a minor in Industrial Engineering back in 2012.
I worked as a Process Design/Operation Engineer in INEOS Koln, mostly on the petrochemical area relating to naphtha treating. There I designed and modeled several processes relating separation of isopentane/pentane mixtures, catalytic reactors and separation processes such as distillation columns, flash separation devices and transportation of tank-trucks of product.
Slides for the eLearning course Separation and purification processes in biorefineries (https://open-learn.xamk.fi) in IMPRESS project (https://www.spire2030.eu/impress).
Section: Mass transfer processes
Subject: 3.1 Design principles
FULL COURSE:
https://courses.chemicalengineeringguy.com/p/flash-distillation-in-chemical-process-engineering/
Introduction:
Binary Distillation is one of the most important Mass Transfer Operations used extensively in the Chemical industry.
Understanding the concept behind Gas-Gas, Liquid-Liquid and the Gas-Liquid mass transfer interaction will allow you to understand and model Distillation Columns, Flashes, Batch Distillator, Tray Columns and Packed column, etc...
We will cover:
REVIEW: Of Mass Transfer Basics (Equilibrium VLE Diagrams, Volatility, Raoult's Law, Azeotropes, etc..)
Distillation Theory - Concepts and Principles
Application of Distillation in the Industry
Equipment for Flashing Systems such as Flash Drums
Design & Operation of Flash Drums
Material and Energy Balances for flash systems
Adiabatic and Isothermal Operation
Animations and Software Simulation for Flash Distillation Systems (ASPEN PLUS/HYSYS)
Theory + Solved Problem Approach:
All theory is taught and backed with exercises, solved problems, and proposed problems for homework/individual study.
At the end of the course:
You will be able to understand mass transfer mechanism and processes behind Flash Distillation.
You will be able to continue with Batch Distillation, Fractional Distillation, Continuous Distillation and further courses such as Multi-Component Distillation, Reactive Distillation and Azeotropic Distillation.
About your instructor:
I majored in Chemical Engineering with a minor in Industrial Engineering back in 2012.
I worked as a Process Design/Operation Engineer in INEOS Koln, mostly on the petrochemical area relating to naphtha treating.
There I designed and modeled several processes relating separation of isopentane/pentane mixtures, catalytic reactors and separation processes such as distillation columns, flash separation devices and transportation of tank-trucks of product.
Absorption & indusrial absorber,Gas Absorption,Equipments,Absorption in chemical Reaction,Absorption in Packed Tower,Absorption for counter current,Choice of Solvent,Continuous Contact Equipment,Height Equivalent to Theoretical Plate,HETP
Slides for the eLearning course Separation and purification processes in biorefineries (https://open-learn.xamk.fi) in IMPRESS project (https://www.spire2030.eu/impress).
Section: Mass transfer processes
Subject: 1.3 Rate and equilibrium
Slides for the eLearning course Separation and purification processes in biorefineries (https://open-learn.xamk.fi) in IMPRESS project (https://www.spire2030.eu/impress).
Section: Mass transfer processes
Subject: 2.2 Molecular diffusion
Slides for the eLearning course Separation and purification processes in biorefineries (https://open-learn.xamk.fi) in IMPRESS project (https://www.spire2030.eu/impress).
Section: Mass transfer processes
Subject: 2.1 Overview
Estimation of Pressure Drop in Pipe Systems
0 INTRODUCTION/PURPOSE
1 SCOPE
2 FIELD OF APPLICATION
3 DEFINITIONS
3.1 units
4 SOURCES OF DATA
5 BASIC CONCEPTS
5.1 Equation for Pressure Change in a Flowing
Fluid
5.2 Static and Stagnation Pressures
5.3 Sonic Flow
6 INCOMPRESSIBLE FLOW IN PIPES OF CONSTANT
CROSS-SECTION
6.1 Straight Circular Pipes
6.2 Ducts of Non-circular Cross-section
6.3 Coils
6.4 General Equation for Incompressible Flow
in Pipes of Constant Cross-section
7 COMPRESSIBLE FLOW IN PIPES OF CONSTANT
CROSS-SECTION
7.1 Isothermal Flow
7.2 Adiabatic Flow
7.3 Estimation of Pressure Drop for Adiabatic
Flow in Pipes of Constant Cross-section
7.4 Ratio of Isothermal to Adiabatic Pressure Drop
8 FLOW IN PIPE FITTINGS
8.1 Incompressible Flow
8.2 Compressible Flow
9 FLOW IN BENDS
9.1 Incompressible Flow in Bends
9.2 Compressible Flow in Bends
10 CHANGES IN CROSS-SECTIONAL AREA
9.1 Incompressible Flow
9.2 Compressible Flow
11 ORIFICES, NOZZLES AND VENTURIS
11.1 Incompressible Flow through an Orifice
11.2 Compressible Flow through an Orifice or Nozzle
11.3 Venturi Choke Tubes
12 VALVES
12.1 General
12.2 Incompressible Flow in Valves
12.2 Compressible Flow in Valves
13 COMBINING AND DIVIDING FLOW
9.1 Incompressible Flow
9.2 Compressible Flow
14 COMPUTER PROGRAMS FOR FLUID FLOW
15 NOMENCLATURE
16 REFERENCES
APPENDICES
A BASIC THERMODYNAMICS
B COMPRESSIBLE FLOW THROUGH ORIFICES
C THE ‘TWO-K’ METHOD FOR FITTING PRESSURE LOSS
Agitation and Mixing are two important unit operations used in industries such as Impellers agitators are widely used to circulate the liquid through the vessel in which the dispersion of liquids and gases into other liquids like mixing of stiff paste, elastomers and dry solids powders takes place.
COURSE LINK:
https://www.chemicalengineeringguy.com/courses/gas-absorption-stripping/
Introduction:
Gas Absorption is one of the very first Mass Transfer Unit Operations studied in early process engineering. It is very important in several Separation Processes, as it is used extensively in the Chemical industry.
Understanding the concept behind Gas-Gas and Gas-Liquid mass transfer interaction will allow you to understand and model Absorbers, Strippers, Scrubbers, Washers, Bubblers, etc…
We will cover:
- REVIEW: Of Mass Transfer Basics required
- GAS-LIQUID interaction in the molecular level, the two-film theory
- ABSORPTION Theory
- Application of Absorption in the Industry
- Counter-current & Co-current Operation
- Several equipment to carry Gas-Liquid Operations
- Bubble, Spray, Packed and Tray Column equipments
- Solvent Selection
- Design & Operation of Packed Towers
- Pressure drop due to packings
- Solvent Selection
- Design & Operation of Tray Columns
- Single Component Absorption
- Single Component Stripping/Desorption
- Diluted and Concentrated Absorption
- Basics: Multicomponent Absorption
- Software Simulation for Absorption/Stripping Operations (ASPEN PLUS/HYSYS)
----
Please show the love! LIKE, SHARE and SUBSCRIBE!
More likes, sharings, suscribers: MORE VIDEOS!
-----
CONTACT ME
Chemical.Engineering.Guy@Gmail.com
www.ChemicalEngineeringGuy.com
http://facebook.com/Chemical.Engineering.Guy
You speak spanish? Visit my spanish channel -www.youtube.com/ChemEngIQA
The Principles required to understand Distillation, Absorption, Stripping, Flashing, Gas Treating, Scrubbing and more!
Introduction:
This course covers all the theory required to understand the basic principles behind Unit Operations that are based on Mass Transfer. Most of these Unit Operations (Equipments) are used in Process Separation Technologies in the Industry.Common examples are Distillation, Absorption and Scrubbing.
This course is required for the following:
Flash Distillation
Gas Absorption & Stripping
Simple Distillation
Batch Distillation
Binary Distillation
Fractional Distillation
Scrubbers
Gas Treating
Sprayers / Spray Towers
Bubble Columns / Sparged Vessels
Agitation Vessels
Packed Towers
Tray Towers
We will cover:
Mass Transfer Basics
Diffusion, Convection
Flux & Fick's Law
The Concept of Equilibrium & Phases
Gibbs Phase Rule
Vapor Pressure
Equilibrium Vapor-Liquid Diagrams (T-xy, P-xy, XY)
Equilibrium Curves
Dew Point, Bubble Point
Volatility (Absolute & Relative)
K-Values
Ideal Cases vs. Real Cases
Henry's Law
Raoult's Law
Deviations of Ideal Cases (Positive and Negative)
Azeotropes
Solubility of Gases in Liquids
Interphase Mass Transfer and its Theories
Two Film Theory
Mass Transfer Coefficients (Overall vs Local)
Getting Vapor-Liquid and Solubility Data
Solved-Problem Approach:
All theory is backed with:
Exercises
Solved problems
Proposed problems
Homework
Case Studies
Individual Study
At the end of the course:
You will be able to understand the mass transfer concepts behind various Unit Operations involving Vapor - Liquid Interaction.
You will be able to apply this theory in further Unit Operations related to Mass Transfer Vapor - Liquid, which is one of the most common interactions found in the industry.
About your instructor:
I majored in Chemical Engineering with a minor in Industrial Engineering back in 2012.
I worked as a Process Design/Operation Engineer in INEOS Koln, mostly on the petrochemical area relating to naphtha treating. There I designed and modeled several processes relating separation of isopentane/pentane mixtures, catalytic reactors and separation processes such as distillation columns, flash separation devices and transportation of tank-trucks of product.
Slides for the eLearning course Separation and purification processes in biorefineries (https://open-learn.xamk.fi) in IMPRESS project (https://www.spire2030.eu/impress).
Section: Mass transfer processes
Subject: 3.1 Design principles
FULL COURSE:
https://courses.chemicalengineeringguy.com/p/flash-distillation-in-chemical-process-engineering/
Introduction:
Binary Distillation is one of the most important Mass Transfer Operations used extensively in the Chemical industry.
Understanding the concept behind Gas-Gas, Liquid-Liquid and the Gas-Liquid mass transfer interaction will allow you to understand and model Distillation Columns, Flashes, Batch Distillator, Tray Columns and Packed column, etc...
We will cover:
REVIEW: Of Mass Transfer Basics (Equilibrium VLE Diagrams, Volatility, Raoult's Law, Azeotropes, etc..)
Distillation Theory - Concepts and Principles
Application of Distillation in the Industry
Equipment for Flashing Systems such as Flash Drums
Design & Operation of Flash Drums
Material and Energy Balances for flash systems
Adiabatic and Isothermal Operation
Animations and Software Simulation for Flash Distillation Systems (ASPEN PLUS/HYSYS)
Theory + Solved Problem Approach:
All theory is taught and backed with exercises, solved problems, and proposed problems for homework/individual study.
At the end of the course:
You will be able to understand mass transfer mechanism and processes behind Flash Distillation.
You will be able to continue with Batch Distillation, Fractional Distillation, Continuous Distillation and further courses such as Multi-Component Distillation, Reactive Distillation and Azeotropic Distillation.
About your instructor:
I majored in Chemical Engineering with a minor in Industrial Engineering back in 2012.
I worked as a Process Design/Operation Engineer in INEOS Koln, mostly on the petrochemical area relating to naphtha treating.
There I designed and modeled several processes relating separation of isopentane/pentane mixtures, catalytic reactors and separation processes such as distillation columns, flash separation devices and transportation of tank-trucks of product.
FULL COURSE:
https://courses.chemicalengineeringguy.com/p/flash-distillation-in-chemical-process-engineering/
Introduction:
Binary Distillation is one of the most important Mass Transfer Operations used extensively in the Chemical industry.
Understanding the concept behind Gas-Gas, Liquid-Liquid and the Gas-Liquid mass transfer interaction will allow you to understand and model Distillation Columns, Flashes, Batch Distillator, Tray Columns and Packed column, etc...
We will cover:
REVIEW: Of Mass Transfer Basics (Equilibrium VLE Diagrams, Volatility, Raoult's Law, Azeotropes, etc..)
Distillation Theory - Concepts and Principles
Application of Distillation in the Industry
Equipment for Flashing Systems such as Flash Drums
Design & Operation of Flash Drums
Material and Energy Balances for flash systems
Adiabatic and Isothermal Operation
Animations and Software Simulation for Flash Distillation Systems (ASPEN PLUS/HYSYS)
Theory + Solved Problem Approach:
All theory is taught and backed with exercises, solved problems, and proposed problems for homework/individual study.
At the end of the course:
You will be able to understand mass transfer mechanism and processes behind Flash Distillation.
You will be able to continue with Batch Distillation, Fractional Distillation, Continuous Distillation and further courses such as Multi-Component Distillation, Reactive Distillation and Azeotropic Distillation.
About your instructor:
I majored in Chemical Engineering with a minor in Industrial Engineering back in 2012.
I worked as a Process Design/Operation Engineer in INEOS Koln, mostly on the petrochemical area relating to naphtha treating.
There I designed and modeled several processes relating separation of isopentane/pentane mixtures, catalytic reactors and separation processes such as distillation columns, flash separation devices and transportation of tank-trucks of product.
Chemical equilirium
Equilibrium constant
Statement of Le Chatelier's Principle
Factors affecting equilibrium
Concentration change
Pressure changes
Temperature changes
Addition of a noble gass
Addition of a catalyst
Applications of LeChatelier's Principle
Equilibrium in physical and chemical processes, dynamic nature of equilibrium, law of mass
action, equilibrium constant, factors affecting equilibrium ‐ Le Chatelier's principle, ionic
equilibrium‐ ionization of acids and bases, strong and weak electrolytes, degree of ionization,
ionization of poly basic acids, acid strength, concept of pH, buffer solution, solubility product,
common ion effect , Arrhenius concept, brownsted lowry concept, acidic buffer, basic buffer, dissociation constant, equilibrium constant, see saw game, equilibrium in solid, liquid and gaseous state, solubility product.
The Principles required to understand Distillation, Absorption, Stripping, Flashing, Gas Treating, Scrubbing and more!
Introduction:
This course covers all the theory required to understand the basic principles behind Unit Operations that are based on Mass Transfer. Most of these Unit Operations (Equipments) are used in Process Separation Technologies in the Industry.Common examples are Distillation, Absorption and Scrubbing.
This course is required for the following:
Flash Distillation
Gas Absorption & Stripping
Simple Distillation
Batch Distillation
Binary Distillation
Fractional Distillation
Scrubbers
Gas Treating
Sprayers / Spray Towers
Bubble Columns / Sparged Vessels
Agitation Vessels
Packed Towers
Tray Towers
We will cover:
Mass Transfer Basics
Diffusion, Convection
Flux & Fick's Law
The Concept of Equilibrium & Phases
Gibbs Phase Rule
Vapor Pressure
Equilibrium Vapor-Liquid Diagrams (T-xy, P-xy, XY)
Equilibrium Curves
Dew Point, Bubble Point
Volatility (Absolute & Relative)
K-Values
Ideal Cases vs. Real Cases
Henry's Law
Raoult's Law
Deviations of Ideal Cases (Positive and Negative)
Azeotropes
Solubility of Gases in Liquids
Interphase Mass Transfer and its Theories
Two Film Theory
Mass Transfer Coefficients (Overall vs Local)
Getting Vapor-Liquid and Solubility Data
Solved-Problem Approach:
All theory is backed with:
Exercises
Solved problems
Proposed problems
Homework
Case Studies
Individual Study
At the end of the course:
You will be able to understand the mass transfer concepts behind various Unit Operations involving Vapor - Liquid Interaction.
You will be able to apply this theory in further Unit Operations related to Mass Transfer Vapor - Liquid, which is one of the most common interactions found in the industry.
About your instructor:
I majored in Chemical Engineering with a minor in Industrial Engineering back in 2012.
I worked as a Process Design/Operation Engineer in INEOS Koln, mostly on the petrochemical area relating to naphtha treating. There I designed and modeled several processes relating separation of isopentane/pentane mixtures, catalytic reactors and separation processes such as distillation columns, flash separation devices and transportation of tank-trucks of product.
Kinetic Gas Theory including Ideal Gas Equation. Temperature, Volume, Applications
Boyle's Law, Charles' Law and Avogadro's Law. Ideal Gas Theory, Dalton's Partial Pressure
English chapter we are going to discuss about the reduction in the oxidation their heat evolution changes occurrence and about their reducing agent and oxidization
An Overview to the most common Industrial Mass Transfer Operations & Process Separation Technologies
Course Description
In this course we will cover the most basic processes involved in Mass Transfer Operations. This is an overview of what type of processes, methods and units are used in the industry. This is mostly an introductory course which will allow you to learn, understand and know the approach towards separation processes involving mass transfer phenomena.
It is an excellent course before any Mass Transfer Process or Unit Operation Course such as Distillations, Extractions, Leaching, Membranes, Absorption, etc...
This course is extremely recommended if you will continue with the following:
Flash Distillation, Simple Distillation, Batch Distillation
Gas Absorption, Desorption & Stripping
Binary Distillation, Fractional Distillation
Scrubbers, Gas Treating
Sprayers / Spray Towers
Bubble Columns / Sparged Vessels
Agitation Vessels
Packed Towers, Tray Towers
Membranes
Liquid Extraction
Dryers / Humidifiers
Adsorbers
Evaporators/Sublimators
Crystallizers
Centrifugations
And many other Separation Technology!
At the end of the Course:
You will be able to understand the mass transfer operations concepts. You will be able to identify Mass Transfer Unit Operations. You will be also able to ensure the type of method of separation technology used.
You will be able to apply this theory in further Unit Operations.
Theory-Based Course
This is a very theoretical course, some calculations and exercises are present, but overall, expect mostly theoretical concepts.
An Overview to the most common Industrial Mass Transfer Operations & Process Separation Technologies
Course Description
In this course we will cover the most basic processes involved in Mass Transfer Operations. This is an overview of what type of processes, methods and units are used in the industry. This is mostly an introductory course which will allow you to learn, understand and know the approach towards separation processes involving mass transfer phenomena.
It is an excellent course before any Mass Transfer Process or Unit Operation Course such as Distillations, Extractions, Leaching, Membranes, Absorption, etc...
This course is extremely recommended if you will continue with the following:
Flash Distillation, Simple Distillation, Batch Distillation
Gas Absorption, Desorption & Stripping
Binary Distillation, Fractional Distillation
Scrubbers, Gas Treating
Sprayers / Spray Towers
Bubble Columns / Sparged Vessels
Agitation Vessels
Packed Towers, Tray Towers
Membranes
Liquid Extraction
Dryers / Humidifiers
Adsorbers
Evaporators/Sublimators
Crystallizers
Centrifugations
And many other Separation Technology!
At the end of the Course:
You will be able to understand the mass transfer operations concepts. You will be able to identify Mass Transfer Unit Operations. You will be also able to ensure the type of method of separation technology used.
You will be able to apply this theory in further Unit Operations.
Theory-Based Course
This is a very theoretical course, some calculations and exercises are present, but overall, expect mostly theoretical concepts.
An Overview to the most common Industrial Mass Transfer Operations & Process Separation Technologies
Course Description
In this course we will cover the most basic processes involved in Mass Transfer Operations. This is an overview of what type of processes, methods and units are used in the industry. This is mostly an introductory course which will allow you to learn, understand and know the approach towards separation processes involving mass transfer phenomena.
It is an excellent course before any Mass Transfer Process or Unit Operation Course such as Distillations, Extractions, Leaching, Membranes, Absorption, etc...
This course is extremely recommended if you will continue with the following:
Flash Distillation, Simple Distillation, Batch Distillation
Gas Absorption, Desorption & Stripping
Binary Distillation, Fractional Distillation
Scrubbers, Gas Treating
Sprayers / Spray Towers
Bubble Columns / Sparged Vessels
Agitation Vessels
Packed Towers, Tray Towers
Membranes
Liquid Extraction
Dryers / Humidifiers
Adsorbers
Evaporators/Sublimators
Crystallizers
Centrifugations
And many other Separation Technology!
At the end of the Course:
You will be able to understand the mass transfer operations concepts. You will be able to identify Mass Transfer Unit Operations. You will be also able to ensure the type of method of separation technology used.
You will be able to apply this theory in further Unit Operations.
Theory-Based Course
This is a very theoretical course, some calculations and exercises are present, but overall, expect mostly theoretical concepts.
This is course on Plant Simulation will show you how to setup hypothetical compounds, oil assays, blends, and petroleum characterization using the Oil Manager of Aspen HYSYS.
You will learn about:
Hypothetical Compounds (Hypos)
Estimation of hypo compound data
Models via Chemical Structure UNIFAC Component Builder
Basis conversion/cloning of existing components
Input of Petroleum Assay and Crude Oils
Typical Bulk Properties (Molar Weight, Density, Viscosity)
Distillation curves such as TBP (Total Boiling Point)
ASTM (D86, D1160, D86-D1160, D2887)
Chromatography
Light End
Oil Characterization
Using the Petroleum Assay Manager or the Oil Manager
Importing Assays: Existing Database
Creating Assays: Manually / Model
Cutting: Pseudocomponent generation
Blending of crude oils
Installing oils into Aspen HYSYS flowsheets
Getting Results (Plots, Graphs, Tables)
Property and Composition Tables
Distribution Plot (Off Gas, Light Short Run, Naphtha, Kerosene, Light Diesel, Heavy Diesel, Gasoil, Residue)
Oil Properties
Proper
Boiling Point Curves
Viscosity, Density, Molecular Weight Curves
This is helpful for students, teachers, engineers and researchers in the area of R&D, specially those in the Oil and Gas or Petroleum Refining industry.
This is a "workshop-based" course, there is about 25% theory and about 75% work!
At the end of the course you will be able to handle crude oils for your fractionation, refining, petrochemical process simulations!
COURSE LINK:
https://www.chemicalengineeringguy.com/courses/petroleum-refining/
COURSE DESCRIPTION:
The main scope of the course is to create strong basis and fundamentals regarding the processes in the Petroleum Refining. We take a look to the Oil&Gas Industry briefly and continue directly with the Refining Process. We then make a focus in each individual unit operation in the refinery.
Learn about:
* Oil& Gas Industry
* Difference between Petroleum Refining vs. Petrochemical Industry
* Overview of the most important operations and products
* Market insight (supply/demand) as well as (production/consumption)
* Several Petroleum Refineries around the World
Unit Operations & Processes
* Refining and Fractionation
* Atmospheric Distillation Column
* Vacuum Distillation
* Hydrotreating (Hydrogenation)
* Blending
* Reforming
* Isomerization
* Alkylation
* Steam Cracking
* Fluid Catalytic Cracking
* Gas Sweetening (Hydrodesulfurization)
* Coking
Components:
* Fuel Gas / Natural Gas
* Liquified Petroleum Gases (LPG)
* Propane, Butane
* Sulfur / Hydrogen Sulfide
* Gasoline / Automotive Gas Oil
* Naphtha Cuts (Light/Heavy)
* Kerosene
* Diesel
* Gasoil
* Lubricants
* Vacuum Residues
* Asphalt
* Coke
NOTE: This course is focused for Process Simulation
At the end of the course you will feel confident in the Petroleum Refining Industry. You will know the most common Process & Unit Operations as well as their distribution, production and importance in daily life.
----
Please show the love! LIKE, SHARE and SUBSCRIBE!
More likes, sharings, suscribers: MORE VIDEOS!
-----
CONTACT ME
Chemical.Engineering.Guy@Gmail.com
www.ChemicalEngineeringGuy.com
http://facebook.com/Chemical.Engineering.Guy
You speak spanish? Visit my spanish channel -www.youtube.com/ChemEngIQA
COURSE LINK:
https://www.chemicalengineeringguy.com/courses/petroleum-refining/
COURSE DESCRIPTION:
The main scope of the course is to create strong basis and fundamentals regarding the processes in the Petroleum Refining. We take a look to the Oil&Gas Industry briefly and continue directly with the Refining Process. We then make a focus in each individual unit operation in the refinery.
Learn about:
* Oil& Gas Industry
* Difference between Petroleum Refining vs. Petrochemical Industry
* Overview of the most important operations and products
* Market insight (supply/demand) as well as (production/consumption)
* Several Petroleum Refineries around the World
Unit Operations & Processes
* Refining and Fractionation
* Atmospheric Distillation Column
* Vacuum Distillation
* Hydrotreating (Hydrogenation)
* Blending
* Reforming
* Isomerization
* Alkylation
* Steam Cracking
* Fluid Catalytic Cracking
* Gas Sweetening (Hydrodesulfurization)
* Coking
Components:
* Fuel Gas / Natural Gas
* Liquified Petroleum Gases (LPG)
* Propane, Butane
* Sulfur / Hydrogen Sulfide
* Gasoline / Automotive Gas Oil
* Naphtha Cuts (Light/Heavy)
* Kerosene
* Diesel
* Gasoil
* Lubricants
* Vacuum Residues
* Asphalt
* Coke
NOTE: This course is focused for Process Simulation
At the end of the course you will feel confident in the Petroleum Refining Industry. You will know the most common Process & Unit Operations as well as their distribution, production and importance in daily life.
----
Please show the love! LIKE, SHARE and SUBSCRIBE!
More likes, sharings, suscribers: MORE VIDEOS!
-----
CONTACT ME
Chemical.Engineering.Guy@Gmail.com
www.ChemicalEngineeringGuy.com
http://facebook.com/Chemical.Engineering.Guy
You speak spanish? Visit my spanish channel -www.youtube.com/ChemEngIQA
COURSE LINK:
https://www.chemicalengineeringguy.com/courses/petrochemicals-an-overview/
Introduction:
The course is mainly about the petrochemical industry. Talks about several chemicals and their chemical routes in order to produce in mass scale the demands of the market.
Learn about:
Petorchemical Industry
Difference between Petroleum Refining vs. Petrochemical Industry
Paraffins, Olefins, Napthenes & Aromatics
Market insight (production, consumption, prices)
Two main Petrochemical Processes: Naphtha Steam Cracking and Fluid Catalytic Cracking
The most important grouping in petrochemical products
Petrochemical physical & chemical properties. Chemical structure, naming, uses, production, etc.
Basic Gases in the industry: Ammonia, Syngas, etc…
C1 Cuts: Methane, Formaldehyde, Methanol, Formic Acid, Urea, Chloromethanes etc…
C2 Cuts: Ethane, Acetylene, Ethylene, Ethylene Dichloride, Vinyl Chloride, Ethylene Oxide, Ethanolamines, Ethanol, Acetaldehyde, Acetic Acid, Ethylene Glycols (MEG, DEG, TEG)
C3 Cuts: Propane, Propylene, Propylene Oxide, Isopropanol, Acetone, Acrylonitrile, Propediene, Allyl chloride, Acrylic acid, Propionic Acid, Propionaldehyde, Propylene Glycol
C4 Cuts: Butanes, Butylenes, Butadiene, Butanols, MTBE (Methyl Tert Butyl Ethers)
C5 cuts: Isoprene, Pentanes, Piperylene, Cyclopentadiene, Dicyclopentadiene, Isoamyl, etc…
Aromatics: Benzene, Toluene, Xylenes (BTX), Cumene, Phenol, Ethyl Benzene, Styrene, Pthalic Anhydride, Nitrobenzene, Aniline, Benzoic Acid, Chlorobenzene, etc…
At the end of the course you will feel confident in how the petrochemical industry is established. You will know the most common petrochemicals as well as their distribution, production and importance in daily life. It will help in your future process simulations by knowing the common and economical chemical pathways.
COURSE LINK:
https://www.chemicalengineeringguy.com/courses/petrochemicals-an-overview/
Introduction:
The course is mainly about the petrochemical industry. Talks about several chemicals and their chemical routes in order to produce in mass scale the demands of the market.
Learn about:
Petorchemical Industry
Difference between Petroleum Refining vs. Petrochemical Industry
Paraffins, Olefins, Napthenes & Aromatics
Market insight (production, consumption, prices)
Two main Petrochemical Processes: Naphtha Steam Cracking and Fluid Catalytic Cracking
The most important grouping in petrochemical products
Petrochemical physical & chemical properties. Chemical structure, naming, uses, production, etc.
Basic Gases in the industry: Ammonia, Syngas, etc…
C1 Cuts: Methane, Formaldehyde, Methanol, Formic Acid, Urea, Chloromethanes etc…
C2 Cuts: Ethane, Acetylene, Ethylene, Ethylene Dichloride, Vinyl Chloride, Ethylene Oxide, Ethanolamines, Ethanol, Acetaldehyde, Acetic Acid, Ethylene Glycols (MEG, DEG, TEG)
C3 Cuts: Propane, Propylene, Propylene Oxide, Isopropanol, Acetone, Acrylonitrile, Propediene, Allyl chloride, Acrylic acid, Propionic Acid, Propionaldehyde, Propylene Glycol
C4 Cuts: Butanes, Butylenes, Butadiene, Butanols, MTBE (Methyl Tert Butyl Ethers)
C5 cuts: Isoprene, Pentanes, Piperylene, Cyclopentadiene, Dicyclopentadiene, Isoamyl, etc…
Aromatics: Benzene, Toluene, Xylenes (BTX), Cumene, Phenol, Ethyl Benzene, Styrene, Pthalic Anhydride, Nitrobenzene, Aniline, Benzoic Acid, Chlorobenzene, etc…
At the end of the course you will feel confident in how the petrochemical industry is established. You will know the most common petrochemicals as well as their distribution, production and importance in daily life. It will help in your future process simulations by knowing the common and economical chemical pathways.
This is a slideshow / resource / support material of the course.
Get full access (videlectures)
https://www.chemicalengineeringguy.com/courses/aspen-plus-bootcamp-with-12-case-studies/
x-x-x
Requirements
Basic understanding of Plant Design & Operation
Strong Chemical Engineering Fundamentals
Aspen Plus V10 (at least 7.0)
Aspen Plus – Basic Process Modeling (Very Recommended)
Aspen Plus – Intermediate Process Modeling (Somewhat Recommended)
Description
This BOOTCAMP will show you how to model and simulate common industrial Chemical Processes.
It is focused on the “BOOTCAMP” idea, in which you will learn via workshops and case studies, minimizing theory to maximize learning.
You will learn about:
Better Flowsheet manipulation and techniques
Understand Property Method Selection and its effects on simulation results
More than 15 Unit Operations that can be used in any Industry
Model Analysis Tools required for process design
Reporting Relevant Results Plot relevant data
Analysis & Optimization of Chemical Plants
Economic Analysis
Dynamic Simulations
At the end of this Bootcamp, you will be able to model more industrial processes, feel confident when modeling new processes as well as applying what you have learnt to other industries.
This is a slideshow / resource / support material of the course.
Get full access (videlectures)
https://www.chemicalengineeringguy.com/courses/aspen-plus-bootcamp-with-12-case-studies/
x-x-x
Requirements
Basic understanding of Plant Design & Operation
Strong Chemical Engineering Fundamentals
Aspen Plus V10 (at least 7.0)
Aspen Plus – Basic Process Modeling (Very Recommended)
Aspen Plus – Intermediate Process Modeling (Somewhat Recommended)
Description
This BOOTCAMP will show you how to model and simulate common industrial Chemical Processes.
It is focused on the “BOOTCAMP” idea, in which you will learn via workshops and case studies, minimizing theory to maximize learning.
You will learn about:
Better Flowsheet manipulation and techniques
Understand Property Method Selection and its effects on simulation results
More than 15 Unit Operations that can be used in any Industry
Model Analysis Tools required for process design
Reporting Relevant Results Plot relevant data
Analysis & Optimization of Chemical Plants
Economic Analysis
Dynamic Simulations
At the end of this Bootcamp, you will be able to model more industrial processes, feel confident when modeling new processes as well as applying what you have learnt to other industries.
LINK:
https://www.chemicalengineeringguy.com/courses/aspen-plus-intermediate-course/
The INTERMEDIATE Aspen Plus Course will show you how to model and simulate more complex Processes
Analysis of Unit Operation will help you in order to simulate more complex chemical processes, as well as to analyse and optimize existing ones.
You will learn about:
- Better Flowsheet manipulation
- Hierarchy, Flowsheeting, Sub-flowsheet creation
- Logical Operators / Manipulators
- Understand Property Method Selection and its effects on simulation results
- Study of more rigorous unit operations
- Model Analysis Tools such as sensitivity and optimization
- Reporting Relevant Results Plot relevant data for Heaters, Columns ,Reactors, Pumps
- Temperature Profiles, Concentration Profile, Pump Curves, Heat Curves, etc…
- Up to 3 Case Studies (in-depth analysis)
All theory is backed up by more than 30 Practical Workshops!
At the end of the course you will be able to setup more complex processes, increase your simulation and flow sheeting techniques, run it and debugging, get relevant results and make a deeper analysis of the process for further optimization.
Course by Chemical Engineering Guy
Check out full course:
http://www.chemicalengineeringguy.com/courses/aspen-plus-physical-properties-course/
Ask me for special discounts, or checkout "SURPIRSE" tab in my site for special discounts.
This is course on Process Simulation will show you how to model, manipulate and report thermodynamic, transport, physical and chemical properties of substances.
You will learn about:
Physical Property Environment
Physical Property Method & Method Assistant
Fluid and Property Packages
Physical property input, modeling, estimation and regression
Thermodynamic Properties (Material/Energy balances and Thermodynamic Processes)
Transport Properties for (Mass/Heat/Momentum Transfer)
Equilibrium Properties (Vapor-Liquid, Liquid-Liquid, etc...)
Getting Results (Plots, Graphs, Tables)
This is an excellent way to get started with Aspen Plus. Understanding the physical property environment will definitively help you in the simulation and flowsheet creation!
This is a "workshop-based" course, there is about 50% theory and about 50% practice!
Get full Course here:
www.ChemicalEngineeringGuy.com/Courses
The BASIC Aspen HYSYS Course will show you how to model and simulate Processes (From Petrochemical, to Ammonia Synthesis and Polymerisation).
Analysis of Unit Operation will help you in order to optimise the Chemical Plant.
This is helpful for students, teachers, engineers and researchers in the area of R&D and Plant Design/Operation.
The course is didactic, with a lot of applied theory and Workshops/Study cases.
At the end of the course you will be able to setup a simulation, run it, get results and more important, analysis of the process for further optimization.
Chemical Engineers
Process Engineers
Students related to engineering fields
Teachers willing to learn more about process simulation
Petrochemical Engineers
The courses, subjects, labs and projects that a student must undergo in order to become a Chemical Engineer.
We divide as follows:
4 blocks:
General Engineering
Theoretical Basis
Unit Operations
Plant Design/Operation
Aspen Plus basic course for Engineers.
Introduction to Process Modeling/Simulation Software.
INDEX:
Course Objectives
Introduction to Aspen Plus
User Interface & Getting Help
Physical Properties
Introduction to Flowsheet
Unit Operation Models
Reporting Results
Case Studies I, II and III
Case Study IV
Conclusion
Applied Fluid Dynamics Course. Part 1 - Incompressible Flow
---
This is a Course Overview of Applied Fluid Dynamics Course.
The course is based in Engineering Applications
---
The course is structured in 7 Blocks
AFD1 The Mechanical Energy Equation
AFD2 Pipe, Fittings and Valves
AFD3 Energy Loss due to Friction
AFD4 Flow Measurement Equipment
AFD5 Pumps
AFD6 Incompressible Flow Applications
AFD7 Agitation and Mixing
Visit www.ChemicalEngineeringGuy.com/Courses for more information!
Explore the innovative world of trenchless pipe repair with our comprehensive guide, "The Benefits and Techniques of Trenchless Pipe Repair." This document delves into the modern methods of repairing underground pipes without the need for extensive excavation, highlighting the numerous advantages and the latest techniques used in the industry.
Learn about the cost savings, reduced environmental impact, and minimal disruption associated with trenchless technology. Discover detailed explanations of popular techniques such as pipe bursting, cured-in-place pipe (CIPP) lining, and directional drilling. Understand how these methods can be applied to various types of infrastructure, from residential plumbing to large-scale municipal systems.
Ideal for homeowners, contractors, engineers, and anyone interested in modern plumbing solutions, this guide provides valuable insights into why trenchless pipe repair is becoming the preferred choice for pipe rehabilitation. Stay informed about the latest advancements and best practices in the field.
Democratizing Fuzzing at Scale by Abhishek Aryaabh.arya
Presented at NUS: Fuzzing and Software Security Summer School 2024
This keynote talks about the democratization of fuzzing at scale, highlighting the collaboration between open source communities, academia, and industry to advance the field of fuzzing. It delves into the history of fuzzing, the development of scalable fuzzing platforms, and the empowerment of community-driven research. The talk will further discuss recent advancements leveraging AI/ML and offer insights into the future evolution of the fuzzing landscape.
Cosmetic shop management system project report.pdfKamal Acharya
Buying new cosmetic products is difficult. It can even be scary for those who have sensitive skin and are prone to skin trouble. The information needed to alleviate this problem is on the back of each product, but it's thought to interpret those ingredient lists unless you have a background in chemistry.
Instead of buying and hoping for the best, we can use data science to help us predict which products may be good fits for us. It includes various function programs to do the above mentioned tasks.
Data file handling has been effectively used in the program.
The automated cosmetic shop management system should deal with the automation of general workflow and administration process of the shop. The main processes of the system focus on customer's request where the system is able to search the most appropriate products and deliver it to the customers. It should help the employees to quickly identify the list of cosmetic product that have reached the minimum quantity and also keep a track of expired date for each cosmetic product. It should help the employees to find the rack number in which the product is placed.It is also Faster and more efficient way.
Sachpazis:Terzaghi Bearing Capacity Estimation in simple terms with Calculati...Dr.Costas Sachpazis
Terzaghi's soil bearing capacity theory, developed by Karl Terzaghi, is a fundamental principle in geotechnical engineering used to determine the bearing capacity of shallow foundations. This theory provides a method to calculate the ultimate bearing capacity of soil, which is the maximum load per unit area that the soil can support without undergoing shear failure. The Calculation HTML Code included.
Quality defects in TMT Bars, Possible causes and Potential Solutions.PrashantGoswami42
Maintaining high-quality standards in the production of TMT bars is crucial for ensuring structural integrity in construction. Addressing common defects through careful monitoring, standardized processes, and advanced technology can significantly improve the quality of TMT bars. Continuous training and adherence to quality control measures will also play a pivotal role in minimizing these defects.
Industrial Training at Shahjalal Fertilizer Company Limited (SFCL)MdTanvirMahtab2
This presentation is about the working procedure of Shahjalal Fertilizer Company Limited (SFCL). A Govt. owned Company of Bangladesh Chemical Industries Corporation under Ministry of Industries.
COLLEGE BUS MANAGEMENT SYSTEM PROJECT REPORT.pdfKamal Acharya
The College Bus Management system is completely developed by Visual Basic .NET Version. The application is connect with most secured database language MS SQL Server. The application is develop by using best combination of front-end and back-end languages. The application is totally design like flat user interface. This flat user interface is more attractive user interface in 2017. The application is gives more important to the system functionality. The application is to manage the student’s details, driver’s details, bus details, bus route details, bus fees details and more. The application has only one unit for admin. The admin can manage the entire application. The admin can login into the application by using username and password of the admin. The application is develop for big and small colleges. It is more user friendly for non-computer person. Even they can easily learn how to manage the application within hours. The application is more secure by the admin. The system will give an effective output for the VB.Net and SQL Server given as input to the system. The compiled java program given as input to the system, after scanning the program will generate different reports. The application generates the report for users. The admin can view and download the report of the data. The application deliver the excel format reports. Because, excel formatted reports is very easy to understand the income and expense of the college bus. This application is mainly develop for windows operating system users. In 2017, 73% of people enterprises are using windows operating system. So the application will easily install for all the windows operating system users. The application-developed size is very low. The application consumes very low space in disk. Therefore, the user can allocate very minimum local disk space for this application.
Forklift Classes Overview by Intella PartsIntella Parts
Discover the different forklift classes and their specific applications. Learn how to choose the right forklift for your needs to ensure safety, efficiency, and compliance in your operations.
For more technical information, visit our website https://intellaparts.com
About
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.
Technical Specifications
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
Key Features
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface
• Compatible with MAFI CCR system
• Copatiable with IDM8000 CCR
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
Application
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.
Overview of the fundamental roles in Hydropower generation and the components involved in wider Electrical Engineering.
This paper presents the design and construction of hydroelectric dams from the hydrologist’s survey of the valley before construction, all aspects and involved disciplines, fluid dynamics, structural engineering, generation and mains frequency regulation to the very transmission of power through the network in the United Kingdom.
Author: Robbie Edward Sayers
Collaborators and co editors: Charlie Sims and Connor Healey.
(C) 2024 Robbie E. Sayers
2. www.ChemicalEngineeringGuy.com
We will analyze mostly Gas-Liquid Interaction
If a certain quantity of a gaseous mixture and a non-
volatile liquid are brought into contact, some components
of the gas may dissolve into the liquid.
The resulting concentration of the dissolved gas in the
liquid is said to be the gas solubility at the prevailing
temperature and pressure.
4. www.ChemicalEngineeringGuy.com
Ammonia is very soluble in water
Some ammonia molecules will immediately travel from the gas phase into the liquid phase
Ammonia crosses the interface separating the 2 phases.
As the molecules of dissolved ammonia increases:
some of the molecules will start to escape back to the gas phase.
5. www.ChemicalEngineeringGuy.com
As more ammonia enters the liquid:
The rate of ammonia returning to the gas increases
Eventually the rate at which it enters the liquid
exactly equals that at which it leaves.
An equilibrium condition now exist between the
gas and liquid.
Although the molecules of ammonia still travel
back and forth from one phase to another
The net transfer is zero.
6. www.ChemicalEngineeringGuy.com
If additional ammonia is injected into the container,
the existing equilibrium is disturbed.
*Le Chatelier
The ammonia molecules will re-distribute themselves
until a new equilibrium is re-established
higher concentrations of ammonia in both gas phase and
liquid phase.
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
7. www.ChemicalEngineeringGuy.com
Such equilibrium relationship between the concentrations is known as the equilibrium
distribution curve or simply
the solubility curve
Most operations will involve interaction between:
Equilibrium Line
Operation Line
Mass Transfer involves the:
Operation Point reaching the Equilibrium Point
8. www.ChemicalEngineeringGuy.com
Recall from Phase Diagrams that:
X-axis mol fraction of Solute (gas) in Liquid Mixture
Y-axis mol fraction of Solute (gas) in Gas Mixture
Typically:
Set for a Given Pressure and Temperature
WHY?
9. www.ChemicalEngineeringGuy.com
The gas absorption process involves the re-distribution of
solute between
the gas phase and the liquid phase
the 2 phases must come into close contact and achieves
equilibrium condition.
The equilibrium distribution curve is the relationship
between
solute concentration in the gas phase and in the liquid phase
constant temperature and pressure
NOTE: Not same for Distillation & Absorption!
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
10. www.ChemicalEngineeringGuy.com
In Distillation:
we have seen that the equilibrium curve simply shows the equilibrium relationship
between 2 components
the more volatile and the less volatile
e.g. Water-ethanol
the points represent vapour-liquid equilibrium at different temperatures.
the solubility curve can lie anywhere in the x-y plot (or p-y plot, etc).
In gas absorption
as noted at the beginning, in the simplest case:
there will be 3 components
e.g. NH3 , air and water
The equilibrium solubility curve is plotted for a particular constant temperature
Any point on the same curve represent gas solubility at the same temperature.
12. www.ChemicalEngineeringGuy.com
Before we actually go and do a proper analysis…
Draw curves depicting the changes that will happen if:
Pressure of system increases
Pressure of system decreases
Temperature increases
Temperature decreases
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
13. www.ChemicalEngineeringGuy.com
Before we actually go and do a proper analysis…
Draw curves depicting the changes that will happen if:
Pressure of system increases
Pressure of system decreases
Temperature increases
Temperature decreases
14. www.ChemicalEngineeringGuy.com
Draw curves depicting the changes that will happen if;:
Pressure of system increases
Pressure of system decreases
Temperature increases
Temperature decreases
SOLUTION
If P increases
• Gas is more soluble in Liquid
• Expect Equilibrium Line to Shift to the Right
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
15. www.ChemicalEngineeringGuy.com
Compare:
HCl, NH3 and SO2
Temperature Effect
Compare
Diff. Species
Vapor Pressure
Relatively insoluble gas is high in concentration in the gas phase
i.e. high partial pressure at equilibrium.
16. www.ChemicalEngineeringGuy.com
High soluble gas has low partial pressure.
In many practical cases, only one component in the gas
mixture is relatively soluble in the liquid
e.g. in the NH3-Air-H2O system
since NH3 is relatively more soluble than air in water
pAir >> pNH3
17. www.ChemicalEngineeringGuy.com
When the gas mixture in equilibrium with an ideal liquid solution follows the ideal
gas behavior
When the solution is non-ideal
Raoult's Law cannot be applied
Most cases, it is more convenient to apply Henry’s Law
Models for ideal solution, real gas
Dilute solution
“ideal-dilute” case
1 1 1 Tx P y P
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
18. www.ChemicalEngineeringGuy.com
The equation for describing non-ideal solutions is the Henry's Law, which states
that (for component-A in a mixture of 2 components):
Where,
pA is the partial pressure of component-A
xA is the mole fraction of component-A in liquid
H is the Henry's Law Constant
Henry's Law is often used for describing gas solubility relationships.
19. www.ChemicalEngineeringGuy.com
Solubility of Gases in Liquids
Typically, as Pressure increases, solubility of gases increases
Henry’s Constant is dependent directly proportional to Temperature
Henry's Law:
Used to represent equilibrium solubility curves.
predicts a linear equilibrium relationship.
Still, most equilibrium relationships are actually non-linear.
Valid at low concentrations dilute.
E Line Henry’s Law
20. www.ChemicalEngineeringGuy.com
Typical Henry’s Law Constants for gases
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
24. www.ChemicalEngineeringGuy.com
Given that typically 0.348 g CO2 / 100 mL water at 0°C, P = 1.00 atm
A) Calculate Henry’s constant in (atm/M; atm/xa)
B) Calculate the solubility of CO2 in water at 0°C P = 3atm
First… Calculate molar quantities.
2
2
44 /
18 /
CO
H O
MW g mol
MW g mol
2
2
0.007909
0.348
44 /
100
5.556
18 /
CO
H O
mass g
mol
MW g mol
mass g
mol mol
MW g mol
25. www.ChemicalEngineeringGuy.com
Now, total mol:
Get molar content of CO2
2
2
0.007909
0.348
44 /
100
5.556
18 /
CO
H O
mass g
mol
MW g mol
mass g
mol mol
MW g mol
2 2
2
2
5.5630.0079 5.556 9
0.0014
.
0.0
5639
079
5
CO H O
CO
CO
mol mol mol
mol
x
mol
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
26. www.ChemicalEngineeringGuy.com
Get Molarity (mol of solute per liter of solution)
Henry’s Constant (atm/M)
0.0079
0.079
0.1
A
solvent
mol mol
M M
L L
1
0.079
A A
A
A
P HxM
P atm
H
M M
12.658atm
MH
Henry’s Constant (atm/xa)
1
0.0014
714.28 A
A
A
atm
x
P atm
H
x
27. www.ChemicalEngineeringGuy.com
B) Calculate the solubility of CO2 in water at 0°C P = 3atm
3.00
12.65
0.2371
8
A A
A
A atm
M
A
P HxM
P atm
M
M
H
M
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
28. www.ChemicalEngineeringGuy.com
1. Introduction to Mass Transfer
Fluxes & Velocities
Molecular Diffusion
Diffusion Coefficient
2. Fick’s Law
Fick’s Model
Case (A) Equimolar Counter-Diffusion (EMD)
Case (B) Unimolecular Diffusion (UMD)
29. www.ChemicalEngineeringGuy.com
(1) diffusion in a quiescent medium
Concentration Gradient from Point A to B
(2) mass transfer in laminar flow
Flow in pipes and Concentration Distribution
(3) mass transfer in the turbulent flow
Mixing in an Agitation Vessel
(4) mass exchange between phases
Gas-Liquid Absorption
Vapor-Liquid Distillation
Molecular Diffusion is STRONG
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
31. www.ChemicalEngineeringGuy.com
When a system contains two or more components whose concentrations vary from
point to point, there is a natural tendency for mass to be transferred, minimizing
the concentration differences within the system and moving it towards equilibrium.
32. www.ChemicalEngineeringGuy.com
The transport of one component from a region of higher concentration to that of a
lower concentration is called mass transfer.
In this example, flow goes from:
High Concentration to Low Concentration
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
33. www.ChemicalEngineeringGuy.com
Mass transfer plays an important role in many industrial processes.
A group of operations for separating the components of mixtures is based on the
transfer of material from one homogeneous phase to another.
These methods-covered by the term “mass transfer operations” include such
techniques as:
distillation, gas absorption, humidification, liquid extraction, adsorption, membrane
separations, and others.
34. www.ChemicalEngineeringGuy.com
The driving force for transfer in these operations is a concentration gradient.
Similar to a temperature gradient provides the driving force for heat transfer.
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
35. www.ChemicalEngineeringGuy.com
Do NOT confuse Mass Transfer with Movement of Mass!
There must be a change in concentration in order to have a Mass Transfer Phenomena
• If color is T
• If color if V
• If color if C
36. www.ChemicalEngineeringGuy.com
Molecular Diffusion
Typically occurs in stagnant conditions or laminar flow
Focuses on layer study
Studied in this Chapter
Convection Mass Transfer
Typically occurs in Turbulent flow
Aka Eddy Diffusion
Focuses in Bulk Studies
Studied in Next Chapter
Interphase Mass Transfer
Mass Transfer between two phases at least… Turbulent Flow typically
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
37. www.ChemicalEngineeringGuy.com
As early as 1815 it was observed qualitatively that whenever a gas mixture contains
two or more molecular species, whose relative concentrations vary from point to
point, an apparently natural process results which tends to diminish any inequalities
in composition.
This macroscopic transport of mass, independent of any convection effects* within
the system, is defined as molecular diffusion
Convection Effects
Due to movement or changes in
velocity/viscosities
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
40. www.ChemicalEngineeringGuy.com
Let us consider:
Non-uniform multi-component fluid mixture
Having bulk motion owing to pressure difference
The different components are moving:
At different molecular velocities as a result of diffusion.
Two types of average velocities with respect to a
stationary observer have been defined for such cases…
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
41. www.ChemicalEngineeringGuy.com
Two types of average velocities
For an n-component system, the mass average velocity in the x-direction is defined:
Another form of average velocity for the mixture is the molar average velocity defined as:
1
1
u
n
i i
i
u
1
1 n
i i
i
U c u
c
42. www.ChemicalEngineeringGuy.com
The velocities u and U:
Are approximately equal at low solute concentrations in binary systems & in nonuniform
mixtures of components having the same molecular weight.
The velocities u and U:
Are also equal in the bulk flow of a mixture with uniform concentration throughout regardless
of the relative molecular weights of the components.
43. www.ChemicalEngineeringGuy.com
Frames of reference:
are the co-ordinates on the basis of which the measurements are made.
Three frames of reference or co-ordinates are commonly used for measuring the
flux of a diffusing component
It is assumed that in a frame of reference
there is an observer who observes or
measures the velocity or flux of a component
in a mixture.
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
44. www.ChemicalEngineeringGuy.com
If the frame of reference or the observer is stationary with respect to the earth:
He notes a velocity ui of the ith component.
That guy is at
u = 1m/s
u = 1 m/s
45. www.ChemicalEngineeringGuy.com
If the observer is located in a frame of reference that moves with a mass average
velocity u of component i:
He will note a velocity (ui – u0) of the component i
This is the relative average velocity of the component with respect to the observer who
himself is moving with the velocity u in the same direction.
Now, I’m at
u = 0 m/s
u = 1 m/s
46. www.ChemicalEngineeringGuy.com
The flux is defined as the rate of transport of species i per unit area in a direction
normal to the transport.
The flux is calculated with respect to a fixed reference frame.
Another convenient expression is:
Relates Velocity + Concentration instead of Mass Flow per unit area (SAME UNITS)
ui fixed reference!
www.ChemicalEngineeringGuy.com
i mol i iN C u
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
47. www.ChemicalEngineeringGuy.com
But…
In a system, since several molecular species move with different average velocities,
a frame of moving reference must be chosen.
The important moving references are mass average, molar average and volume
average velocities.
Imagine moving a bottle inside a car…
The car is moving at 60 km/h
You move the bottle inside at 1m/s
We care the velocity of the bottle inside the car!
www.ChemicalEngineeringGuy.com
48. www.ChemicalEngineeringGuy.com
That’s why it is convenient to interpret the total flux of species “i” with respect to
an arbitrary reference frame rather than a fixed set of reference frame (typically,
the velocity of material in a pipe or equipment)
The molar flux of species i based on arbitrary reference velocity u0 is denoted by Ji-
mol which can be defined as
www.ChemicalEngineeringGuy.com
0( )i mol i iJ C u u
49. www.ChemicalEngineeringGuy.com
A gas mixture containing 65% NH3, 8% N2, 24% H2 and 3% Ar is flowing through a pipe
25 mm in diameter at a total pressure of 4.0 atm.
The velocities of the components are as follows:
Topic: Estimation of mass average, molar average velocity and volume average
velocity
A) Calculate the mass average velocity
B) the molar average velocity
C) the volume average velocity of the gas mixture.
3
2
2
0.030
0.030
0.035
0.020
m
s
m
s
m
s
m
s
NH
N
H
Ar
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
50. www.ChemicalEngineeringGuy.com
A) Calculate the mass average velocity
From the definition of velocity:
We can know that:
ti = density of ith component
t = total density of gas mix
MWi = molar weight of ith component
MW = average molar weight of the mix.
1
1 1 2 2 3 3 4 4
1
1
( )
n
i i
i
u u
u t u t u t u t u
;i
i i
p p
t MW t MW
RT RT
51. www.ChemicalEngineeringGuy.com
Substitute in the expression for mass average velocity (u)
Now, calculate the average Molecular Weight (MW)=
Calculating the “sum”
Substitute in previous equation:
4
1
1
i i i
i
u y u MW
MW
1 1 2 2 3 3 4 4
(0.65 17) (0.08 28) (0.24 2) (0.03 40) 14.97
MW y MW y MW y MW y MW
MW x x x x
4
1
(0.65 17 0.03) (0.08 28 0.03) (0.24 2 0.035) (0.03 40 0.02 0.43 5) 9i i i
i
y u MW x x x x x x x x
4
1
0.4395
1
0.02935
4.
8
97
i i i
m
i
s
y u MW
u
MW
u
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
52. www.ChemicalEngineeringGuy.com
B) Molar average velocity
From the equation “U”:
Now, substitute the values given:
1 1 2 2 3 3 4 4
1 1 2 2 3 3 4 4
1 1 2 2 3 3 4 4
1
( )
1 1 1 1
( ) ( ) ( ) ( )
U
U c u c u c u c u
c
U c u c u c u c u
c c c c
y u y u y u y u
1 1 2 2 3 3 4 4U (0.65 0.03) (0.08x 0.03) (0.24x 0.035) (0.03 0.02)
U 0.0309m
s
y u y u y u y u x x
53. www.ChemicalEngineeringGuy.com
C) the volume average velocity of the gas mixture.
In this specific case, since we are talking about ideal gases:
. . 0.0309m
sVolumeavg Velocity Molar avg Velocity
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
54. www.ChemicalEngineeringGuy.com
Molecular diffusion or molecular transport can be defined as:
transfer or movement of individual molecules through a fluid by means of random,
individual movements of the molecules.
The molecules travel only in straight lines and in the process, may collide with
other molecules in their path.
The molecules then change direction (still in a straight line) after the collision.
This is sometimes referred to as a random-walk process as shown below:
www.ChemicalEngineeringGuy.com
55. www.ChemicalEngineeringGuy.com
Movement due to thermal molecules
Kinetic theory Erratic Movement of A and B
rate of diffusion is defined the total distance travelled per unit time
Rate of Diffusion = Total Distance / total time
Increasing Temperature favors increase in thermal energy, therefore, increase in
Rate of Diffusion
Decrease in Pressure favors decrease in collisions.
If this is true, the total distance or free mean path will be higher, hence, faster rate.
www.ChemicalEngineeringGuy.com
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
57. www.ChemicalEngineeringGuy.com
Molecular diffusion in gases is caused by random
movement of molecules due to their thermal energy
and hence the kinetic theory of gases helps to
understand the mechanism of molecular diffusion in
gases.
According to this theory:
molecules of gases move with very high speed.
For instance, at 273 K temperature and 101.3 kN/m2
pressure, the mean speed of oxygen molecules is
about 462 m/s.
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
58. www.ChemicalEngineeringGuy.com
It may, therefore, be expected that the rate of molecular diffusion should be very
high.
But actually molecular diffusion is an extremely slow process since the molecules
undergo several billion collisions per second
Therefore, their velocities frequently change both in magnitude and direction, thus
making the effective velocity very low.
From now on:
Assume convective MT is faster in rate!
Convective MT is aka Eddys Diffusion
60. www.ChemicalEngineeringGuy.com
Identify:
Molecular Diffusion Phenomena
Convective MT
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
62. www.ChemicalEngineeringGuy.com
Diffusivity or Diffusion Coefficient is a measure of the capability of a substance or
energy to be diffused or to allow something to pass by diffusion.
The constant value: DAB
As you can imagine, the higher the coefficient/diffusivity, the faster the rate of
mass transfer
Diffusivity is a rate of diffusion, a measure of the rate at which particles or fluids
can spread.
63. www.ChemicalEngineeringGuy.com
Typically we would cover:
Diffusivities
Gas
Liquid
Solids
Estimation
Fullers Equations
Chapman-Enskog Equation
Wilke-Chang Equation
Experiment
Twin Bulb
Stefan Tube
Diaphragm Method
We will only cover this topic for
GAS/Vapor-Liquid Operations
64. www.ChemicalEngineeringGuy.com
In general, you will obtain diffusivity of A through B:
Reference/Bibliography/Literature or previous experimentation reported data
Estimations via correlation equations
Experimentation
Units
m2/s
cm2/s
Typical ranges
Gases
Liquids
Solids
Clearly, solids have much lower rates of diffusion… Why?
www.ChemicalEngineeringGuy.com
25
10 m
s
210
10 m
s
2 210 15
10 10m m
s sto
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
67. www.ChemicalEngineeringGuy.com
1. Fick’s Law
Fick’s Model
Case (A) Equimolar Counter-Diffusion (EMD)
Case (B) Unimolecular Diffusion (UMD)
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
68. www.ChemicalEngineeringGuy.com
Fick’s Law
commonly used in basic sciences to describe diffusion
Typically under no turbulence
Mass Transfer Coefficient
The coefficient, k takes care of several parameters which cannot be directly measured
Requires correlations commonly used in engineering
Cylinders, Heaters, Spheres, Tubes, etc.
Both the models have striking similarity with Ohm’s law.
69. www.ChemicalEngineeringGuy.com
First described the molecular diffusion in:
Isothermal, isobaric binary system of components A and B
According to his idea of molecular diffusion:
the molar flux of a species relative to an observer moving with molar average velocity is
proportional to the concentration gradient in a certain direction.
Proportionality Constant Diffusivity or Diffusivity Constant
Typically Done per Axis (Z)
www.ChemicalEngineeringGuy.com
Minus (-) Sign
Drop in concentration toward
direction of Diffusion
AdC
J
dZ
A
AB
dC
J D
dZ
B
B BA
dC
J D
dZ
A
A AB
dC
J D
dZ
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
70. www.ChemicalEngineeringGuy.com
Assumptions:
Isobaric
Isothermal
No chemical reaction
DAB is constant
One Dimension
Dilute solutions
Steady State
Minus (-) Sign
Drop in concentration toward
direction of Diffusion
A
AB
dC
J D
dZ
72. www.ChemicalEngineeringGuy.com
Fick’s Law must be applied to each individual case.
Some common applications:
Steady-State Diffusion:
Through Non-Diffusing Component in Steady-State
Through a Constant Area in Steady-State
Through Variable Area in Steady-State
Through Figures (Plane Wall, Hollow Cylinder, Spheres, Disks, etc...)
Unsteady-State Diffusion
Diffusion through Liquids & Solids
It is not our scope to account for all of the mass transfer cases
We use the most common ones of interest in engineering (Diffusion of Gases)
www.ChemicalEngineeringGuy.com
73. www.ChemicalEngineeringGuy.com
Examples:
Diffusion of component A through a stagnant layer of component B
Equimolar counter-diffusion of two components
Non-equimolal Counter-Diffusion of Two Components
Diffusion Through Moving Bulk Fluid
Case (A) - Equimolar Counter-Diffusion (EMD) in Steady-State
Case (B) - Unimolecular Diffusion (UMD) in Steady State
www.ChemicalEngineeringGuy.com
74. www.ChemicalEngineeringGuy.com
For any given case, we know that the molar flux of A is given by:
Total Molar Flux of A = Molar Flux of A due to Molecular Diffusion + Molar Flux of A due to Bulk Velocity
For a binary case:
www.ChemicalEngineeringGuy.com
A A A
A A A
N J c V
N J y N
( )A A A A BN J y N N
A BN N N
PA2
PB2A
B
Total P
Distance, z
PA1
PB1
75. www.ChemicalEngineeringGuy.com
In equimolar counter-diffusion, the molar fluxes of A and B are equal, but opposite
in direction, and the total pressure is constant throughout.
Hence we can write:
We know that Fick’s Law:
www.ChemicalEngineeringGuy.com
(0)A A A
A A
N J y
N J
PA2
PB2A
B
Total P
Distance, z
PA1
PB1
0
( )A A A B
A B
AN J
f N N
N
i
y N
N
A
A AB
dC
J D
dZ
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
76. www.ChemicalEngineeringGuy.com
For this specific Case:
www.ChemicalEngineeringGuy.com
PA2
PB2A
B
Total P
Distance, z
PA1
PB1
A
A A AB
A
AA B
dC
N J D
dZ
dC
D
dZ
N
Under equimolar counter-diffusion, the diffusivity
of A in B is the same as the diffusivity of B in A:
i.e.
Also: AB BAD D
A B
A B
N N
J J
77. www.ChemicalEngineeringGuy.com
Now, for Ideal Gas Case
We know that:
www.ChemicalEngineeringGuy.com
A A
A
A
A A
A
A
PV nRT
P V n RT
n
C
V
n P
V RT
P
C
RT
PA2
PB2A
B
Total P
Distance, z
PA1
PB1
A
ABA
d
d
N
C
D
z
A
ABA
d
d
N
C
D
z
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
78. www.ChemicalEngineeringGuy.com
The differentials
Which can be simplified to:
Solving now for the 1st Order Differential Equation
www.ChemicalEngineeringGuy.com
PA2
PB2A
B
Total P
Distance, z
PA1
PB1
A
AB B
A
A AA
P
RTN N
d
dC
D D
dZ dz
AB A
A A
P
N J
R
D
dT
d
z
AB A
AB
A
A A
P
J
RT
J
D d
dz
D
P
R
dz d
T
79. www.ChemicalEngineeringGuy.com
Integrating
Limits:
Z1 to Z2
PA1 to PA2
Further Simplification for JA:
www.ChemicalEngineeringGuy.com
2 2
1 1
A
A
A A
Pz
AB
A A
z P
AB
J P
RT
D
J dz dP
D
RT
dz d
PA2
PB2A
B
Total P
Distance, z
PA1
PB1
2 1
2 1
2 1
2 1
( ) ( )
( )
( )
AB
A A A
A AAB
A
D
J z z P P
RT
P PD
J
RT z z
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
80. www.ChemicalEngineeringGuy.com
For B is the same case, as
www.ChemicalEngineeringGuy.com
PA2
PB2A
B
Total P
Distance, z
PA1
PB1
2 1
1 2
2 1
2 1
( )
( )
( )
( )
( )
0
B B B A B
B B
B BA B
B B BA
B BBA
B
A B
B BAB
B
A B
N J y N N
N J
dC D dP
N J D
dz RT dz
P PD
J
RT z z
J J
if N N N
P PD
J
RT z z
Referencing to A
82. www.ChemicalEngineeringGuy.com
Ammonia gas (A) and nitrogen (B) are stored in 2 large storage tanks respectively.
A uniform tube 0.10 m long connects the 2 tanks
The partial pressure of A:
www.ChemicalEngineeringGuy.com
A B
L=0.1m
5
1.013 10
298
tanks
tanks
P x Pa
T K
1
2
4
4
1 1.013 10
2, 0.507 10
A
A
point is p x Pa
point p x Pa
2
3
4
0.230 10
8.314
m
sAB
m Pa
molK
D x
R
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
84. www.ChemicalEngineeringGuy.com
(a) Calculate the flux JA at steady-state.
We can assume this is equimolar since:
Moles flow from A to and B to
Total Mol flux = 0, since P, T, V are constant
Recall that:
Since these are gases, then… Assume Ideal Gas Law (Why?)
www.ChemicalEngineeringGuy.com
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
85. www.ChemicalEngineeringGuy.com
(a) Calculate the flux JA at steady-state.
From our previous equations… Get JA
Note that we have all!
www.ChemicalEngineeringGuy.com
PA1
PA2
2 1
2 1
( )
( )
A AAB
A
P PD
J
RT z z
2 1 0.10L z z m 2
3
4
0.230 10
8.314
m
sAB
m Pa
molK
D x
R
A B
L=0.1m
86. www.ChemicalEngineeringGuy.com
(a) Calculate the flux JA at steady-state.
Substitute all in equation
NOTE: Use only SI-units
www.ChemicalEngineeringGuy.com
2 1
2
3
2
2
2 1
4 4 4
4
( )
( )
(2.3 10 )(0.507 10 1.1013 10 )
8.314 (298 )(0.10 )
0.0004932
4.932 10
A AAB
A
m
s
A m Pa
molK
mol
A m s
mol
A m s
P PD
J
RT z z
x x x Pa
J
K m
J
J x
A B
L=0.1m
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
87. www.ChemicalEngineeringGuy.com
(b) Repeat for JB.
Use Dalton law of Partial Pressure to get PB1 and PB2
www.ChemicalEngineeringGuy.com
1 2
2 2
1 1
2 2
1 1
4 4
5 4 4
5 4 4
(1.013 10 ); (1.013 10 );P (0.507 10 );
(1.0132x10 0.507 10 ) 9.625 10
(1.013x10 1.1013 10 ) 9.119 10
T A B
B T A
T A A
B T A
B T A
B T A
B T A
P P P
P P P
P x Pa P x Pa x Pa
P P P
P P P
P P P x Pa x Pa
P P P x Pa x Pa
2
1
4
4
9.625 10
9.119 10
B
B
P x Pa
P x Pa
A BL=0.1m
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
89. www.ChemicalEngineeringGuy.com
Compare JA and JB
As expected… (in different directions)
Assumption of equimolar condition is correct!
www.ChemicalEngineeringGuy.com
2
2
4
4
4.9322 10
4.9322 10
mol
A m s
mol
B m s
A B
J x
J x
J J
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
90. www.ChemicalEngineeringGuy.com
Two bulbs are connected by a straight tube, 0.001m (0.1cm) in diameter and 0.15m
(15cm) in length.
Initially the bulb at End 1 contains N2 and the bulb at End 2 contains H2
Pressure and temperature are constant at 25°C and 1 atm.
At a time after diffusion starts, tf, the nitrogen content of the gas at:
End 1 of the tube is 80 mol%
End 2 is 25 mol%
Example 3.1 Separation Process
Principles, J. D. Seader, 3rd Edition
L=0.15m 21
N2 H2
91. www.ChemicalEngineeringGuy.com
If the binary diffusion coefficient is 0.784 cm2/s, determine:
(a) The rates and directions of mass transfer in mol/s
(b) The species velocities relative to stationary coordinates, in cm/s
Example 3.1 Separation Process
Principles, J. D. Seader, 3rd Edition
L=0.15m 21
N2 H2
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
92. www.ChemicalEngineeringGuy.com
(A) The rates and directions of mass transfer in mol/s
Because the gas system is closed and at constant pressure and temperature
no bulk flow occurs
mass transfer in the connecting tube is EMD
The area for mass transfer through the tube, in cm2 is given as follows:
A BN N
22 0.1
2 2
3 2
A
7.85 10
D
A x cm
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
93. www.ChemicalEngineeringGuy.com
By the ideal gas law:
Take as the reference plane End 1 of the connecting tube.
Apply the equation:
3
51
(82.06c)(298 ) 4.09 10
P
RT
atm molP
RT K cm
PV nRT C
C x
2 2
2
1 2
2 1
5
3
9
( )
(4.09 10 )(0.784)
0.80 0.25 (7.85 10 )
(15)
9.23 10 /
AB
A N N
A
A N
cD
J x x A
z z
x
J x
J J x mol s
1 2A A
2 1
(x x )
( )
AB
A
cD
J
z z
94. www.ChemicalEngineeringGuy.com
(b) The species velocities relative to stationary coordinates, in cm/s
This case is valid for EMD:
the molar-average velocity of the mixture,
Therefore, assume that:
the species velocities are equal to species diffusion velocities.
2 2
2 2
2 2
N N
N N D
N N
J n
v v
C Acx
0 /U mol s
2 2
2 2
2 2
H H
H H D
H H
J n
v v
C Acx
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
95. www.ChemicalEngineeringGuy.com
(b) The species velocities relative to stationary coordinates, in cm/s
Solving:
When End 1, xN2 = 0.80
When End 1, xN2 = 0.80
2
2
2 2 2
2 2
2
2 2
9
3 5
9.23 10 0.0287
(7.85 10 )(4.09 10 )
0.0287 0.0287
N
N
N N N
N H
H
H N
n x
v
Acx x x x x
v v
v
x x
2
2
0.0287 0.028
0
7
0.8
.035875 /
0
N
N
cm sv
x
When End 2, xN2 = 0.25
2
2
0.0287 0.0287
0.25
0.1148 /N
N
v
x
cm s
When End 2, xH2 = 0.75
2
2
0.0287 0.0287
0.75
0.03826 /H
N
v
x
cm s
2
2
0.0287 0.0287
0.20
0.1435 /H
N
v
x
cm s
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
96. www.ChemicalEngineeringGuy.com
So… when is v = 0m/s?
CASE: End 2:
Then:
When End 2, xN2 = 0.25
2
2
0.0287 0.0287
0.25
0.1148 /N
N
v
x
cm s
When End 2, xH2 = 0.75
2
2
0.0287 0.0287
0.75
0.03826 /H
N
v
x
cm s
2 2 2 2
0.1148 / ) 0.03826 / ) 0cm/ s(0.25)( (0.75)(
M N N H H
M cm s cm
v x v x
s
v
v
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
97. www.ChemicalEngineeringGuy.com
Note that we are in fact using steady state
Many questions I get:
Why if Concentration changing?
Why is Pressure changing?
Why velocities changes?
My main Answer:
changes with respect to LOCATION that is, the distance
Time is irrelevant
PA2
PB2A
B
Total P
Distance, z
PA1
PB1
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
98. www.ChemicalEngineeringGuy.com
A binary gaseous mixture of components A and B at a pressure of 1 bar and
temperature of 300 K undergoes steady-state equimolar counter-diffusion along a 1-
mm-thick diffusion path
At one end of the path the mole fraction of component A is 70%, while at the other
end it is 20%.
Under these conditions, DAB = 0.1 cm2/s.
A) Calculate the molar flux of component A.
99. www.ChemicalEngineeringGuy.com
A) Calculate the molar flux of component A.
Direct substitution into equation
1 2 1 2
1 2 1 2
3
2
A A A A
2 1 2 1
A A A A
2 1 2 1
5 2 5
3
mol
m s
(x x ) (x x )
( ) ( )
( ) ( )
( ) ( )
(1.0x10 m / s)(1.0x10 )(0.7 0.2)
8.314 300 (1.0 10 )
0.20
AB
P
ABRTAB
A
D P
RT AB
A
A m Pa
molK
A
DcD
J
z z z z
D P
J x x x x
z z RT z z
Pa
J
K x m
J
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
100. www.ChemicalEngineeringGuy.com
A mixture of He and N2 gas is contained in a pipe at:
T= 298K
P = 1 atm
Flow = constant flow throughout
Conditions:
At one end, point 1, PA1 of He = 0.6 atm
At the other end, point 2, PA2 of He = 0.2 atm
Note that the distance is 20 cm between each other.
A) Calculate the flux of He at steady state
Example 6.1-1 From Transport Processes
and Unit Operations, Geankopolis 3rd.
Molecular diffusion of he in N2
24
0.687 10 m
AB sD x
101. www.ChemicalEngineeringGuy.com
Solution
Total Pressure is constant trough time and pipe!
C must be constant as well.
Use either:
Since P is given, use “P”
; / /V nRT n V P RT C
2 1 2 1 2 1
2 1 2 1 2 1
( ) ( ) (P )
( ) ( ) ( )
A A A A A AAB
A AB AB
C C x x PD
J D cD
z z z z RT z z
102. www.ChemicalEngineeringGuy.com
Substitute in:
2 1
2
2
3
2
2 1
4
4
8
(P )
( )
(0.687 10 ) (0.6 0.2 )
(0.082 )(298K) (0.2m)
(0.687 10 ) (0.6 0.2 )x(101325Pa/ atm)
(0.2m)(8.314 )(298K)
(2.772 10 )(151987.5)
0.0
A AAB
A
m
s
A Latm
molK
m
s
A Pa m
molK
mol
A m s
A
PD
J
RT z z
x atm atm
J
x atm atm
J
J x
J
2
2
3
04214
4.2 10
mol
m s
mol
A m s
J x
103. www.ChemicalEngineeringGuy.com
Air
As the name implies, there is only a species diffusing through a stagnant medium
Typical Examples:
Evaporation of Species A through B
Quasi-steady State will be required
B
e
n
z
e
n
e
Air Flow
B
e
n
z
e
n
e
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
104. www.ChemicalEngineeringGuy.com
The general 1-Dimensional, steady state equation
And we know…
Substituting Fick’s Law and Total mol flux
www.ChemicalEngineeringGuy.com
;A
A A B
C
y N N N
C
( )
( )
A A
A AB A B
A A
A AB A
dC C
N D N N
dz C
dC C
N D N
dz C
A A A
A A A
N J c V
N J y N
Total Molar Flux of A = Molar Flux of A due to Molecular Diffusion + Molar Flux of A due to Bulk Velocity
105. www.ChemicalEngineeringGuy.com
This is our “general equation”
In a stagnant medium:
We will work these cases:
Concentrations
Partial Pressures
Molar Fractions
www.ChemicalEngineeringGuy.com
( )A A
A AB A B
dC C
N D N N
dz C
A A
A AB A
dC C
N D N
dz C
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
106. www.ChemicalEngineeringGuy.com
UMD Case – Partial Pressures
We will get from:
To:
Working:
Concentrations
A A
A AB A
dC C
N D N
dz C
2
1
A
2 1 A
C
ln
( ) C
AB
A
ccD
N
z z c
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
107. www.ChemicalEngineeringGuy.com
Since there is no diffusion of B:
Substitute in
We get
www.ChemicalEngineeringGuy.com
BN 0
( )A A
A AB A B
dC C
N D N N
dz C
( 0)
( )
A A
A AB A
A A
A AB A
dC C
N D N
dz C
dC C
N D N
dz C
Working:
Concentrations
108. www.ChemicalEngineeringGuy.com
Substitute in previous equation:
www.ChemicalEngineeringGuy.com
( )
1
1
A A
A AB A
A A
A A AB
A A
A AB
A A
A AB
A
A AB
A
A
A AB
A
dC C
N D N
dz C
C dC
N N D
C dz
C dC
N D
C dz
c C dC
N D
c dz
dCc
N D
c C dz
dC
N cD
c C dz
Working:
Concentrations
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
109. www.ChemicalEngineeringGuy.com
Substitute in previous equation:
www.ChemicalEngineeringGuy.com
2 2
1 1
2 2
1 1
1
1
1
1
A
A
A
A
A
A AB
A
A AB A
A
Cz
A AB A
Az C
Cz
A AB A
Az C
dC
N cD
c C dz
N dz cD dC
c C
N dz cD dC
c C
N dz cD dC
c C
Working:
Concentrations
2 1
1
2
1
2
2
1
2 1 A A
A
2 1
A
A
2 1 A
A
2 1 A
( ) ln( C ) ( ln( C ))
C
( ) ln
C
C
ln
( ) C
C
ln
( ) C
A AB
A AB
AB
A
AB
A
N z z cD c c
c
N z z cD
c
ccD
N
z z c
ccD
N
z z c
110. www.ChemicalEngineeringGuy.com
Our main equation:
www.ChemicalEngineeringGuy.com
Working:
Concentrations2
1
A
2 1 A
C
ln
( ) C
AB
A
ccD
N
z z c
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
111. www.ChemicalEngineeringGuy.com
UMD Case – Partial Pressures
We will get from:
To:
Working:
Partial Pressures
2
12 1
ln
( )
AAB
A
A
P PD P
N
RT z z P P
( )A A
A AB A B
dC C
N D N N
dz C
112. www.ChemicalEngineeringGuy.com
Since there is no diffusion of B:
Substitute in
We get
www.ChemicalEngineeringGuy.com
Working:
Partial PressuresBN 0
( )A A
A AB A B
dC C
N D N N
dz C
( 0)
( )
A A
A AB A
A A
A AB A
dC C
N D N
dz C
dC C
N D N
dz C
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
113. www.ChemicalEngineeringGuy.com
From ideal gas:
Substitute in all CA
Substitute in previous equation:
www.ChemicalEngineeringGuy.com
Working:
Partial Pressures
AC AP
RT
1
A
A A A
P
d
dC dP dPRT
dz dz RTdz RT dz
( )
1
( )
1
( )
A A
A AB A
A A
A AB A
A A
A AB A
dC C
N D N
dz C
dP C
N D N
RT dz C
dP C
N D N
RT dz C
114. www.ChemicalEngineeringGuy.com
Now, given that the ratios of pressure-concentration are the same
Substitute in:
And we get:
www.ChemicalEngineeringGuy.com
Working:
Partial Pressures
1
( )A A
A AB A
dP C
N D N
RT dz C
A AP C
P C
1
( )
1
( )
1
1
A A
A AB A
A A
A A AB
A A
A AB
dP P
N D N
RT dz P
P dP
N N D
P RT dz
P dP
N D
P RT dz
115. www.ChemicalEngineeringGuy.com
Solve Diff. Equation
www.ChemicalEngineeringGuy.com
Working:
Partial Pressures
2 2
1 1
2 2
1 1
1
1
1
1
1
1
1
A
A
A
A
A A
A AB
A
A AB
A
AB A
A
A
Pz
AB A
A
Az P
Pz
AB A
A
Az P
P dP
N D
P RT dz
dP
N dz D
PRT
P
D dP
N dz
PRT
P
D dP
N dz
PRT
P
D dP
N dz
PRT
P
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
116. www.ChemicalEngineeringGuy.com
Solve Diff. Equation
www.ChemicalEngineeringGuy.com
Working:
Partial Pressures2 2
1 1
2 2
1 1
2 2
1 1
2
1
2 1
1
1
1
( )
A
A
A
A
A
A
A
A
Pz
AB A
A
Az P
Pz
AB
A A
Az P
Pz
AB
A A
Az P
P
AB
A A
AP
D dP
N dz
PRT
P
D P
N dz dP
RT P P
D P
N dz dP
RT P P
D P
N z z dP
RT P P
117. www.ChemicalEngineeringGuy.com
Solve Diff. Equation
www.ChemicalEngineeringGuy.com
Working:
Partial Pressures
2
12 1
ln
( )
AAB
A
A
P PD P
N
RT z z P P
1
2
2
1
2
1
2 1
2 1
2 1
( ) ln
( ) ln
ln
( )
AAB
A
A
AAB
A
A
AAB
A
A
P PD P
N z z
RT P P
P PD P
N z z
RT P P
P PD P
N
RT z z P P
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
118. www.ChemicalEngineeringGuy.com
We get our equation:
www.ChemicalEngineeringGuy.com
Working:
Partial Pressures
2
12 1
ln
( )
AAB
A
A
P PD P
N
RT z z P P
119. www.ChemicalEngineeringGuy.com
UMD Case – Molar Fractions
We will get from:
To:
( )A A
A AB A B
dC C
N D N N
dz C
Working:
Molar Fractions
2
1
A
2 1
1
N ln
( ) 1
AAB
A
yCD
z z y
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
120. www.ChemicalEngineeringGuy.com
From our initial equation
Force yA in Fick’s Law
Get Diff. Equation
www.ChemicalEngineeringGuy.com
A
A AB A
dC
N D y N
dz
A
A AB A
dy
N cD y N
dz
A
A
N (1 )
N
(1 )
A
A A AB
A
A AB
AB A
A
dy
N y N cD
dz
dy
y cD
dz
cD dy
y dz
Working:
Molar Fractions
121. www.ChemicalEngineeringGuy.com
Solve Diff. Equation
www.ChemicalEngineeringGuy.com
2 2
1 1
2 2
1 1
A
A
A
A
N
(1 )
N
(1 )
N
(1 )
N
(1 )
A
A
A
A
AB A
A
A
AB
A
z y
A
AB
Az y
z y
A
AB
Az y
cD dy
y dz
dy
dz cD
y
dy
dz cD
y
dy
dz cD
y
Working:
Molar Fractions
122. www.ChemicalEngineeringGuy.com
Solve Diff. Equation
www.ChemicalEngineeringGuy.com
2 2
1 1
1
2
1
2
2
1
A
A 2 1
A
2 1
A
2 1
N
(1 )
1
N ( ) ln
1
1
N ln
( ) 1
1
N ln
( ) 1
A
A
z y
A
AB
Az y
A
AB
A
AAB
A
AAB
A
dy
dz cD
y
y
z z cD
y
ycD
z z y
ycD
z z y
2
1
A
2 1
1
N ln
( ) 1
AAB
A
yCD
z z y
Working:
Molar Fractions
123. www.ChemicalEngineeringGuy.com
Compare!
www.ChemicalEngineeringGuy.com
2
1
A
2 1
1
N ln
( ) 1
AAB
A
ycD
z z y
2
12 1
ln
( )
AAB
A
A
P PPD
N
RT z z P P
Working:
Molar Fractions
Working:
Partial Pressures
Working:
Concentrations
2
1
A
2 1 A
C
ln
( ) C
AB
A
ccD
N
z z c
2
12 1
ln
( )
AAB
A
A
P PcD
N
z z P P
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
124. www.ChemicalEngineeringGuy.com
Oxygen (A) is diffusing through carbon dioxide (B) under steady-state conditions,
with the CO2 non-diffusing.
www.ChemicalEngineeringGuy.com
Path
Non-Diffusion
1
2
2
5
3
4
4
5
10
273
2.0 2.0 10
1.30 10
0.65 10
1.87 10
A
A
m
AB s
P Pa
T K
L mm x m
P x Pa
P x Pa
D x
125. www.ChemicalEngineeringGuy.com
(a) Calculate the molar flux of O2 in the mixture.
Assume Unimolecular Diffusion of Oxygen
CO2 is not diffusing…
www.ChemicalEngineeringGuy.com
L=2.0mm
Non-Diffusion
5
10
273
P Pa
T K
1
4
1.30 10AP x Pa
2
4
0.65 10AP x Pa
25
1.87 10 m
AB sD x
126. www.ChemicalEngineeringGuy.com
Substitute all data:
www.ChemicalEngineeringGuy.com
L=2.0mm
Non-Diffusion
5
10
273
P Pa
T K
1
4
1.30 10AP x Pa
2
4
0.65 10AP x Pa
25
1.87 10 m
AB sD x
2
1
3
2
2
2 1
5 2 5 4 4
4 43
ln
( )
(1.87 10 / )(10 ) 10 10 0.65 10
ln
10 10 1.30 108.314 (273 )(2 10 )
0.4119 ln(1.0747)
0.02967
AAB
A
A
A Pa m
molK
mol
A m s
mol
A m s
P PD P
N
RT z z P P
x m s Pa x x
N
x xK x m
N
N
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
127. www.ChemicalEngineeringGuy.com
(a) Calculate the molar flux of O2 in the mixture.
www.ChemicalEngineeringGuy.com
2 2 2
0.02967 / 2.967 10 /AN mol m s x mol m s
L=2.0mm
Non-Diffusion
5
10
273
P Pa
T K
1
4
1.30 10AP x Pa
2
4
0.65 10AP x Pa
25
1.87 10 m
AB sD x
128. www.ChemicalEngineeringGuy.com
(b) Calculate the total moles in diffusion per unit area in 5 seconds
(c) if the spill is 0.45 m2; calculate molar flow
www.ChemicalEngineeringGuy.com
2
2
(2.967 10 / 2 )(5s)
0.14835 /
A A
A
mol N t x mol m s
mol mol m
2 2 2
(2.967 x10 mol/ m s)(0.45m )
0.01335 /
A A
A
F N A
F mol s
L=2.0mm
Non-Diffusion
5
10
273
P Pa
T K
1
4
1.30 10AP x Pa
2
4
0.65 10AP x Pa
25
1.87 10 m
AB sD x
129. www.ChemicalEngineeringGuy.com
An open beaker, 6 cm high, is filled with liquid benzene (A) at 25°C to within 0.5 cm of the top.
EXAMPLE 3.2 Evaporation from an Open
Beaker. Separation Process Principles, J.
D. Seader, 3rd Edition
Dry air (B) at 25°C and 1 atm is blown across the mouth of the
beaker so that evaporated benzene is carried away by convection
after it transfers through a stagnant air layer in the beaker.
The vapor pressure of benzene at 25°C is 0.131 atm.
Air
Liquid Benzene
6.0 cm
0.5 cm
1 atm; 25°C
130. www.ChemicalEngineeringGuy.com
The mole fraction of benzene in the air at the top of the beaker is 0.0
It can be determined by Raoult’s law at the gas–liquid interface.
Diffusion coefficient (benzene in air):
at 25°C and 1 atm
DAB = 0.0905 cm2/s.
Neglect the accumulation of benzene and air in the stagnant layer
with time as it increases in height
This is te so called Quasi-steady-state assumption
EXAMPLE 3.2 Evaporation from an Open
Beaker. Separation Process Principles, J.
D. Seader, 3rd Edition
Air
Liquid Benzene
6.0
cm
0.5
cm
1 atm;
25°C
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
131. www.ChemicalEngineeringGuy.com
Calculate:
(a) initial rate of evaporation of benzene as a molar flux in mol/cm2-s;
(b) initial mole-fraction profiles in the stagnant air layer;
(c) initial fractions of the mass-transfer fluxes due to molecular diffusion;
(d) initial diffusion velocities
EXAMPLE 3.2 Evaporation from an Open
Beaker. Separation Process Principles, J.
D. Seader, 3rd Edition
132. www.ChemicalEngineeringGuy.com
Before we start…
Since Dalton’s Law is valid
And stated that Raoult’s Law can be applied:
1 1
1 1
1 1
1 1
1 1
0.131
1
0.131
1.0; 0.131
A sat A
sat
A A
A A
A A
A A
x P y P
P
y x
P
y x
y x
x y
We use x and y interchangeably in this case
Air
Liquid Benzene
6.0
cm
0.5
cm
1 atm;
25°C
133. www.ChemicalEngineeringGuy.com
(a) initial rate of evaporation of benzene as a molar flux in mol/cm2-s;
Use UMD equation for molar fractions (WHY?)
The total vapor concentration by the ideal-gas law is:
5 3
1
82.06 298
4.09 10 /
P
C
RT
C
x
C x mol cm
2
1
A
2 1
1
N ln
( ) 1
AAB
A
yCD
z z y
First, let us calculate
C; DAB; Z2-Z1
2
1
A
2 1
1
N ln
( ) 1
AAB
A
yCD
z z y
Working:
Molar Fractions
134. www.ChemicalEngineeringGuy.com
Now, assume that z equal to the distance down from the top of the beaker:
z1 = 0.000m; at the top of beaker
z2 = 0.005m; the distance from the top of the beaker to gas–liquid interface.
Therefore, the layer will be:
We can then state the compositions of Benzene in z1 and z2
2 1 0.005-0.000=0.005m=0.50z z dz cm
1 1
2 2
( 0.00)
( 0.50)
0.131
0.000
A z
A z
x
x
Air
Liquid Benzene
6.0
cm
0.5
cm
1 atm;
25°C
z2
z1
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
135. www.ChemicalEngineeringGuy.com
Substitute in Equation
2
1
A
2 1
1
N ln
( ) 1
AAB
A
yCD
z z y
Working:
Molar Fractions
2
1
A
2 1
5
A
A
6
A
6 2
A
1
N ln
( ) 1
(4.09 10 )(0.0905) 1 0.00
N ln
(0.5 0) 1 0.131
N (0.000007402)(0.14075)
N 0.00000104195 1.04 10
N 1.04 10 /
AAB
A
yCD
z z y
x
x
x mol cm s
1 1 1
2 2 2
( 0.00)
( 0.50)
0.131
0.000
A A z
A A z
y x
y x
We use x and y
interchangeably in
this case
136. www.ChemicalEngineeringGuy.com
(b) initial mole-fraction profiles in the stagnant air layer;
Assume quasi-steady-state
No accumulation of species in time
Constant molar density
Ctotal is constant, as:
• P,T are constant
NA is constant, as:
• Quasi state
Air
B
e
n
z
e
n
e
Z2=0.50cm
Z1=0.00cm x1=0.131
x2=0.000
P
r
o
f
i
l
e
Using zx and xAx for “x any
point between z2 and z1
137. www.ChemicalEngineeringGuy.com
The integral form, solving for “xAx” the concentration
at any point “Zx”
1 1
1
1
1
6
5
2 1
( )
(1.04 10 )( 0)
(4.09 10 )(0.0905)
0.281
1
1
ln
( ) 1
1 (1 )
1 (1 0.131)
1 0.869
Ax x
A
x
A x
AB
x
x
x
x
x
xz
AB A
A Az x
AAB
A
A
N z z
cD
A A
x z
x
A
z
A
cD dx
dz
N x
xcD
N
z z x
x x e
x e
x e
Air
B
e
n
z
e
n
e
Z2=0.50cm
Z1=0.00cm x1=0.131
x2=0.000
P
r
o
f
i
l
e
Zx=x-cm xAx=?
We want to
• propose “Z” value and obtain
“X” value
138. www.ChemicalEngineeringGuy.com
The table:
These profiles are only slightly curved
In this case, you could model as straight line
0.281
1 0.869 ; 1x
x x x
z
A B Ax e x x
z (cm) xA xB
0.0 0.1310 0.8690
0.05 0.1187 0.8813
0.1 0.1062 0.8938
0.15 0.0936 0.9064
0.2 0.0808 0.9192
0.25 0.0678 0.9322
0.3 0.0546 0.9454
0.35 0.0412 0.9588
0.4 0.0276 0.9724
0.45 0.0139 0.9861
0.5 0.0000 1.0000
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
139. www.ChemicalEngineeringGuy.com
(c) initial fractions of the mass-transfer fluxes due to molecular diffusion
Bulk-Flow Flux
Molecular Diffusion Flux
For this specific case:
For the stagnant component, (Air or B) becomes
0;
0
B
B B A BA
B
B
B A BA
B
B A BA
B
B B A BA
B A
dx
N x N cD
dz
N stagnant
dx
x N cD
dz
dx
x N cD
dz
dx
J x N cD
dz
J J
140. www.ChemicalEngineeringGuy.com
(c) initial fractions of the mass-transfer fluxes due to molecular diffusion
z (cm) xA xB xA*NA xB*NA JB JA
0.00 0.1310 0.8690 1.3624E-07 9.0376E-07 9.0376E-07 -9.0376E-07
0.05 0.1187 0.8813 1.2345E-07 9.1655E-07 9.1655E-07 -9.16547E-07
0.10 0.1062 0.8938 1.1048E-07 9.2952E-07 9.2952E-07 -9.29516E-07
0.15 0.0936 0.9064 9.7332E-08 9.4267E-07 9.4267E-07 -9.42668E-07
0.20 0.0808 0.9192 8.3994E-08 9.5601E-07 9.5601E-07 -9.56006E-07
0.25 0.0678 0.9322 7.0468E-08 9.6953E-07 9.6953E-07 -9.69532E-07
0.30 0.0546 0.9454 5.675E-08 9.8325E-07 9.8325E-07 -9.8325E-07
0.35 0.0412 0.9588 4.2837E-08 9.9716E-07 9.9716E-07 -9.97163E-07
0.40 0.0276 0.9724 2.8728E-08 1.0113E-06 1.0113E-06 -1.01127E-06
0.45 0.0139 0.9861 1.442E-08 1.0256E-06 1.0256E-06 -1.02558E-06
0.50 0.0000 1.0000 0 0.00000104 0.00000104 -0.00000104
B
B B A BA
dx
J x N cD
dz
B AJ J
141. www.ChemicalEngineeringGuy.com
(d)
initial diffusion velocities
From:
;
A B
M
i i A B
iD AD BD
i i A B
i iD M
N NN
v
C C
J J J J
v v v
C x C x C x C
v v v
vM= molar average mixture velocity
viD= diffusion velocity of species “i”
Vi= velocity of species “i”
viD= diffusion velocity of species “i”
142. www.ChemicalEngineeringGuy.com
Accordingly:
z (cm) xA xB JB JA vAD vBD
0.00 0.1310 0.8690 9.0376E-07 -9.0376E-07 0.168678027 -0.025427873
0.05 0.1187 0.8813 9.16547E-07 -9.16547E-07 0.188783884 -0.025427873
0.10 0.1062 0.8938 9.29516E-07 -9.29516E-07 0.213927575 -0.025427873
0.15 0.0936 0.9064 9.42668E-07 -9.42668E-07 0.246270102 -0.025427873
0.20 0.0808 0.9192 9.56006E-07 -9.56006E-07 0.289414642 -0.025427873
0.25 0.0678 0.9322 9.69532E-07 -9.69532E-07 0.349850521 -0.025427873
0.30 0.0546 0.9454 9.8325E-07 -9.8325E-07 0.44056655 -0.025427873
0.35 0.0412 0.9588 9.97163E-07 -9.97163E-07 0.591906119 -0.025427873
0.40 0.0276 0.9724 1.01127E-06 -1.01127E-06 0.89508972 -0.025427873
0.45 0.0139 0.9861 1.02558E-06 -1.02558E-06 1.808515543 -0.025427873
0.50 0.0000 1.0000 0.00000104 -0.00000104 #DIV/0! -0.025427873
;A B
AD BD
A B
J J
v v
x C x C
C=Constant
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
143. www.ChemicalEngineeringGuy.com
Water in the bottom of a narrow metal tube is held at
constant
Temperature = 293K
The total pressure of air is P = 1 atm.
Temperature of air is also T = 293K
P°vap (20°C)= 17.54 mm Hg = 0.023 atm
Water evaporates and diffuses through air in the tube which
length = 0.1524 m
D = 0.25x10-4 m2/s
A) Calculate the rate of evaporation (kgmol/s-m-2)
EXAMPLE 6.2-2 Diffusion of Water through
stagnant, non-diffusing Air. Transport Process
& Unit Operations. Genkopolis. 3rd Ed.
144. www.ChemicalEngineeringGuy.com
Water in the bottom of a narrow metal tube is held at
constant
Temperature = 293K
The total pressure of air is P = 1 atm.
Temperature of air is also T = 293K
P°vap (20°C)= 17.54 mm Hg = 0.023 atm
Water evaporates and diffuses through air in the tube which
length = 0.1524 m
D = 0.25x10-4 m2/s
A) Calculate the rate of evaporation (kgmol/s-m-2)
EXAMPLE 6.2-2 Diffusion of Water through
stagnant, non-diffusing Air. Transport Process
& Unit Operations. Genkopolis. 3rd Ed.
Point 2
Point 1
Air
Water
Length of tube
145. www.ChemicalEngineeringGuy.com
Solution:
Since we are working mostly with pressure:
We must first calculate Partial Pressures in both ends:
2
12 1
ln
( )
AAB
A
A
P PD P
N
RT z z P P
2 1
; ;A A totalP P P
Point 2
Point 1
Air
Water
Length of tube
PT=1atm
PT=1atm
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
146. www.ChemicalEngineeringGuy.com
Note that:
Only 2 gases, 2 points
Point 1
Point 2
Point 2
Point 1
Air
Water
Length of tube
PT=1atm
1
0
1
T
water
Air
P atm
P atm
P atm
0.023
0.023 0.977
1
1
T
water vap
Air
P atm
P P atm
atm a matm tP
A B totalP P P
A B totalP P P
147. www.ChemicalEngineeringGuy.com
Substitute all data:
Point 2
Point 1
Air
Water
Length of tube
PT=1atm
1
0
1
T
water
Air
P atm
P atm
P atm
2
12 1
ln
( )
AAB
A
A
P PD P
N
RT z z P P
2
1
1 0
ln ln 0.02273
1 0.023
A
A
P P atm atm
P P atm atm
4 2
2 1
(0.25x10 / )(101325 )
0.0068232
( ) (8.314 / )(293 )(0.1524 )
ABD P m s Pa
RT z z J molK K m
4 2
7 2
0.02273 0.0068232 0.00015509
1.55 10 / m
1.55 10 / m
A
A
A
N x
N x mol s
N x kmol s
0.023
0.023 0.977
1
1
T
water vap
Air
P atm
P P atm
atm a matm tP
148. www.ChemicalEngineeringGuy.com
1. Convective Mass Transfer
2. Mass Transfer Coefficients
The MT Coefficient
Analogies
3. MT Coefficient Correlations
Correlation for Disks, Plates & Sphere
Correlation for Cylinders & Pipes
Correlation for Packed Beds & Fluidized Beds
Correlation for Tray Columns
Correlation Hollow-Fiber Membrane Modules (Shell & Tube)
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
149. www.ChemicalEngineeringGuy.com
(1) diffusion in a quiescent medium
Concentration Gradient from Point A to B
(2) mass transfer in laminar flow
Flow in pipes and Concentration Distribution
(3) mass transfer in the turbulent flow
Mixing in an Agitation Vessel
(4) mass exchange between phases
Gas-Liquid Absorption
Vapor-Liquid Distillation
Convective MT is STRONG
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
152. www.ChemicalEngineeringGuy.com
Molecular Diffusion vs. Convective Mass Transfer
Types of Models:
Detailed physical description based on Fick‘s laws and the diffusion coefficient.
Engineering approach based on the Mass Transfer Coefficient, MTC or k
153. www.ChemicalEngineeringGuy.com
Check out:
https://www.youtube.com/watch?v=BaBMXgVBQKk
Try to imagine how to model:
Fick’s Law
Eddys Diffusion
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
154. www.ChemicalEngineeringGuy.com
Convective mass transfer occurs due to:
the bulk motion of the fluid the mass transfer is faster compared to the molecular diffusion.
Convective mass transfer is of two types
forced convection mass transfer
free convection mass transfer.
Another analogy:
mass diffusion + bulk fluid motion
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
157. www.ChemicalEngineeringGuy.com
In some cases of convective mass transfer:
may be possible to calculate the rate of mass transfer by solving the
differential equations obtained from mass and momentum balance provided
the nature of the flow is properly defined.
Typical examples are:
absorption of a gas in a laminar liquid film falling down along a wall
dissolution of a solid coated on a flat plate in a liquid flowing over the plate.
158. www.ChemicalEngineeringGuy.com
BUT!
In more complex situations such as:
gas-liquid contact in a packed or plate column
dissolution of a solid in a mechanically stirred vessel
theoretical calculations for rate of mass transfer
It becomes quite difficult and may even be impossible
for the complex nature of the flow.
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
159. www.ChemicalEngineeringGuy.com
Recall Heat Transfer:
Rate of Heat transfer = (HT Coefficient)(Area)(Change in Temperature)
The coefficient, “h” depends on:
Fluid Conditions:
Temperature, Pressure, viscosity, density
Figure being used:
In this case a Pipe
Characteristic Length: Diameter
We would want to do this for MT as well!
Q h A dT
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
160. www.ChemicalEngineeringGuy.com
When a fluid if flowing outside a solid surface, such as a cylinder, sphere, plate, etc.
in forced convection (i.e. Convective MT):
We can express the rate of convective mass transfer from the surface to the fluid,
fluid to surface as follows:
An analogy:
Rate of Transfer (Q) Heat transfer vs. Mass Transfer (NA)
Driving Force Change in Temperature vs. Change in Concentration
Constant h might be the thermal equivalent to kc for mass transfer
As with Heat Transfer, kc has correlations for several figures
We will explore Kc in this section!
( )A c f iN k C C
Q h A dT
161. www.ChemicalEngineeringGuy.com
REMEMBER
Mass-transfer problems involving flowing fluids are often solved using mass-transfer coefficients,
which are analogous to heat-transfer coefficients.
For mass transfer, a composition-driving force replaces DT.
Because composition can be expressed in a number of ways:
Expect different mass-transfer coefficients
Mol fraction, mass/volume, mass/mass, volume/volume, mol/mol, etc…
partial pressure difference (only for gases), concentration difference and mole fraction difference.
If concentration (Mol per liter) is used, dCA is selected as the driving force:
Units:
the inverse of resistance to mass transfer.
( )A c f iN k C C
Note:
The gradient for heat
was Temperature
change.
There is only one way
to “show”
temperature.
mol
time area driving force
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
162. www.ChemicalEngineeringGuy.com
Let’s apply our new concept of “mass transfer coefficient” to our old friends!
EMD – Equimolar diffusion
UMD – Unimolecular diffusion
Equations are already available for predicting the rates of molecular diffusion.
Therefore, mass transfer coefficients as such are not required for cases where only
molecular diffusion is involved.
But in order to have uniformity with eddy diffusion and to develop design
equations for some complex situations:
Mass Transfer Coefficients are also used in molecular diffusion!
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
163. www.ChemicalEngineeringGuy.com
Let us consider the following transfer:
From: component A from the bulk of a gas
To: the bulk of a liquid through the gas-liquid interface.
The transfer in the bulk of gas which is in turbulent motion
is by eddy diffusion
The near we go to the interface:
is by molecular diffusion.
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
164. www.ChemicalEngineeringGuy.com
The rate of transfer for the gas section
Similarly:
the rate of transfer of A from the interface to the bulk of the
liquid may be expressed as
G iA A(p' p' )GA GN k
i LA A(c c )LA LN k
pAi
In this diagram:
L bulkA AC C
165. www.ChemicalEngineeringGuy.com
Where;
= partial pressures of component A in the bulk of the gas
= partial pressures of component A at the interface
= concentrations of component A at the interface
= concentrations of component A at the interface in the bulk of the liquid
G iA A(p' p' )GA GN k
i LA A(c c )LA LN k
G
L
mol
A time area
mol
A time area
N rateof transferof A from gas phase
N rateof transferof A fromliquid phase
Pr
G
moles
k gas phaseMT coefficient
time area d essureof i
L
moles
k liquid phaseMT coefficient
time area dConcentration
' GAp
' iAp
iAc
LAc
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
167. www.ChemicalEngineeringGuy.com
We will now try to “force” mass transfer coefficients in previous EMD & UMD Case.
Recall that here, molecular diffusion is stronger than eddy’s diffusion
The Main Goal:
Obtain an equation with:
Rate of Mass Transfer
Mass Transfer Coefficient
Driving Force
We want this for:
Bulk, interphase and liquid, gas phases
( )(d )coefficientRateof MT MT riving force
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
168. www.ChemicalEngineeringGuy.com
Try to imagine:
EMD Case:
2 1 2 1 2 1
2 1 2 1 2 1
2 1 2 1 2 1
2 1 2 1 2 1
2 1 2 1 2 1
( ) ( ) (P )
( ) ( ) ( )
( ) ( ) (P )
( ) ( ) ( )
( ) ( ) (P )
A A A A A AAB
A AB AB
AB AB AB
A A A A A A A
A C A A x A A P A A
C C x x PD
J D cD
z z z z RT z z
D cD D
J C C x x P
z z z z z z RT
N F C C F x x F P
169. www.ChemicalEngineeringGuy.com
Try to imagine:
UMD Case:
1 2
1 2
A
,
A
,
N (y y )
N ( )
G
A A
B LM
L
A A
B LM
F
y
F
x x
x
2
1
2
1
2 1
2 1
1
ln
( ) 1
1
ln
( ) 1
G
L
AAB
A
A
AAB
A
A
yD
N
RT z z y
xD
N
RT z z x
Harder to get directly the:
Rate of MT = MTC x Driving Force
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
170. www.ChemicalEngineeringGuy.com
In Equimolar Diffusion:
NA = NB (opposite directions)
No bulk-motion contribution to the flux, which facilitates the equation
Flux can be related almost linearly
A B
A A
A
A B A A
A
N N
N N
N N N N
undeffinined
2 1 2 1 2 1
2 1 2 1 2 1
( ) ( ) (P )
( ) ( ) ( )
A A A A A AAB
A A AB AB
C C x x PD
N J D cD
z z z z RT z z
A AN J
171. www.ChemicalEngineeringGuy.com
Then, if applied to a Liquid – Gas Interphase:
Where x liquid phase, y vapor phase
2 1 2 1 2 1
2 1 2 1 2 1
( ) ( ) (P )
( ) ( ) ( )
A A A A A AAB
A A AB AB
C C x x PD
N J D cD
z z z z RT z z
2 1 2 1
2 1 2 1 2 1
2 1 2 1
2 1 2 1 2 1
( ) ( )
( ) ( )
(P ) (y ) ( )
( ) ( ) ( )
L
G
A A A A
A AB AB
A A A A A AAB
A AB AB
C C x x
N D cD
z z z z
P y C CD
N cD D
RT z z z z z z
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
172. www.ChemicalEngineeringGuy.com
Then, forcing the MTC:
For the liquid phase:
For the gas phase
1 2 1 2 1 2
' ( ) ' ( ) ' ( )
G
A G A A y A A c A AN k p p k y y k c c
1 2 1 2
' ( ) ' ( )LA L A A x A AN k c c k x x
2 1 2 1
2 1 2 1 2 1
2 1 2 1
2 1 2 1 2 1
( ) ( )
( ) ( )
(P ) (y ) ( )
( ) ( ) ( )
L
G
AB AB
A A A A A
AB AB AB
A A A A A A A
D cD
N C C x x
z z z z
D cD D
N P y C C
RT z z z z z z
NOTE!
Differ form “k” and
“k’”
k’ = EMD, k = UMD
173. www.ChemicalEngineeringGuy.com
For the liquid phase:
For the gas phase
Relationship:
' ' '
' '
G G c y
L L x
P
F k p k k
RT
F k c k
1 2 1 2 1 2
' ( ) ' ( ) ' ( )
G
A G A A y A A c A AN k p p k y y k c c
1 2 1 2
' ( ) ' ( )LA L A A x A AN k c c k x x
FG and FL will be defined
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
175. www.ChemicalEngineeringGuy.com
A packed-bed distillation column is used to adiabatically separate a mixture of
methanol and water at a total pressure of 1 atm.
Methanol-the more volatile of the two component diffuses from the liquid phase
toward the vapor phase, while water diffuses in the opposite direction.
Assuming that the molar latent heat of vaporization is similar for the two
components, this process is usually modeled as one of equimolar counter diffusion.
At a point in the column, the mass-transfer coefficient is estimated as
Mole fractions of methanol:
The gas-phase methanol mole fraction at the interface is 0.707
While at the bulk of the gas it is 0.656
A) Estimate the methanol flux at that point.
Example 2.3 Mass-Transfer Coefficient in a
Packed-Bed Distillation Column. Principles
and Modern Applications of Mass Transfer
Operations, Jaime Benitez, 2nd Edition
2
5
1.62 10 kmol
kPa m s
x
176. www.ChemicalEngineeringGuy.com
Analysis:
Assume EMD is true
From the units given, it can be inferred that the coefficient given in the problem
statement is k’G
The MTC is given with Pressure units as well, therefore, gas phase
Flux will be calculate almost directly with the equation.
Non-Diluted case! No worries!
' ' '
' '
G G c y
L L x
P
F k p k k
RT
F k c k
1 2 1 2 1 2
' ( ) ' ( ) ' ( )
G
A G A A y A A c A AN k p p k y y k c c
177. www.ChemicalEngineeringGuy.com
Solution:
Equimolar counter diffusion can be assumed in this case
It will be shown in a later chapter, this is the basis of the McCabe-Thiele method of analysis of
distillation columns
Methanol diffuses from the interface towards the bulk of the gas phase; therefore
yA1 = 0.707
yA2 = 0.656.
Since they are not limited to dilute solutions:
k'-type mass-transfer coefficients may be used to estimate the methanol flux.
178. www.ChemicalEngineeringGuy.com
Recall that we have related the equations for MTC in EMD
We can either:
Use
Requires Partial Pressure calculation
Or Use
Requires k’y calculation
1 2 1 2 1 2 1 2
c
A A c A A A A G A A
' k' k'
' (p p ) k' ( ) k' ( ) F ( )
G y
y
G
A G
P
k P
RT
N k c c y y y
F
y
1 2A Ak' ( )A yN y y
1 2A A' (p p )A GN k
k' 'y Gk P
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
179. www.ChemicalEngineeringGuy.com
Let us calculate k’y
2 2
2 2
1 2
5 3
3 5
A A
k' ' (1.62 10 )(101.3 ) 1.64 10
' (y ) (1.64 10 )(0.707 0.656) 8.36 10
kmol kmol
y G kPa m s m s
kmol kmol
A y kPa m s m s
k P x kPa x
N k y x x
180. www.ChemicalEngineeringGuy.com
Recall that we have related the equations for MTC in EMD
We get
1 2 1 2 1 2 1 2
c
A A c A A A A G A A
' k' k'
' (p p ) k' ( ) k' ( ) F ( )
G y
y
G
A G
P
k P
RT
N k c c y y y
F
y
2 2
2 2
1 2
5 3
3 5
A A
k' ' (1.62 10 )(101.3 ) 1.64 10
' (y ) (1.64 10 )[101.3 (0.707 0.656)] 8.36 10
kmol kmol
y G kPa m s m s
kmol kmol
A G kPa m s m s
k P x kPa x
N k y x kPa x
2 2
2 2
1 2
5 3
3 5
A A
k' ' (1.62 10 )(101.3 ) 1.64 10
' (p p ) (1.64 10 )(0.707 0.656 ) 8.36 10
kmol kmol
y G kPa m s m s
kmol kmol
A G kPa m s m s
k P x kPa x
N k x kPa kPa x
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
181. www.ChemicalEngineeringGuy.com
In Molecular diffusion, we require “Ji” from Fick’s Law + Bulk Velocity:
Which we then obtained:
Developed:
i i i i iN J cV J y N
( )A A
A AB A AB A A B
dy dy
N cD y N cD y N N
dz dz
2
1
A
2 1
1
N ln
( ) 1
AAB
A
ycD
z z y
2
12 1
ln
( )
AAB
A
A
P PcD
N
z z P P
Working:
Molar Fractions
Working:
Partial Pressures
Working:
Concentrations
2
1
A
2 1 A
C
ln
( ) C
AB
A
ccD
N
z z c
182. www.ChemicalEngineeringGuy.com
If
Which can be translated to concentrations as well:
2 1( )
ABcD
F
z z
• Note that for any case (UMD, EMD) this expression:
• Repeats a lot…
• This is the so called “characteristic” property of molecular diffusion.
• We will replace it by F, a mass-transfer coefficient
• Technically, a “Local MTC”
2 1( )
ABcD
z z
2 2
1 1
A
2 1
1 1
N ln ln
( ) 1 1
A AAB
A A
y ycD
F
z z y y
2 2
1 1
A A
2 1 A A
C C
ln ln
( ) C C
AB
A
c ccD
N F
z z c c
2 2
1 12 1
ln ln
( )
A AAB
A
A A
P P P PcD
N F
z z P P P P
183. www.ChemicalEngineeringGuy.com
Since the surface through which the transfer takes place may not be plane
This will make that the diffusion path in the fluid may be of variable cross section
NA is defined as the flux at the phase interface or boundary where:
substance A enters or leaves the phase for which F has been defined.
2
G
1
A
1
N ln
1
A
G
A
y
F
y
2
1
A
A
C
ln
CGA G
c
N F
c
2
1
lnG
A
A G
A
P P
N F
P P
2
1
A
1
N ln
1L
A
L
A
x
F
x
2
1
A
A
C
ln
CLA L
c
N F
c
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
184. www.ChemicalEngineeringGuy.com
We can then assign coefficients to their respective phase:
Liquid Phase:
Gas Phase:
Force dY and dX
2 1
2 1
A A
A A
(x x )
(c )
II
A L
II
A L
N F
N F c
2 1
2 1
2 1
A A
A A
A A
( )
( )
(p )
II
A G
II
A G
II
A G
N F y y
N F c c
N F p
2
G
1
A
1
N ln
1
A
G
A
y
F
y
2
1
A
A
C
ln
CGA G
c
N F
c
2
1
lnG
A
A G
A
P P
N F
P P
2
1
A
1
N ln
1L
A
L
A
x
F
x
2
1
A
A
C
ln
CLA L
c
N F
c
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
185. www.ChemicalEngineeringGuy.com
In reality, this can’t be simply done, as we must algebraically manipulate the
natural logarithm differences.
But… We could use a new coefficient:
2
1
1
ln
1
A
A G
A
y
N F
y
2
1
1
ln
1
A
A L
A
x
N F
x
2 1A A
,LM
(x x )L
A
B
F
N
x
2 1A A
,LM
( )G
A
B
F
N y y
y
,LM ,LM
; GL
x y
B B
FF
k k
x y
2 1A A(x x )A xN k
2 1A A( )A yN k y y
2 1 2 2 1
12
1
2 2 1 2 1 2
1 1
,LM
,LM
1 ,LM 1 ,LM
ln
ln
1 1 (1 ) 1
ln ln
1 1
B B B B B
B
B BB
B
B B B B B B
B B B B
x x x x x
x
x xx
x
x x x x x x
x x x x
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
186. www.ChemicalEngineeringGuy.com
Note that we have many ways to model “concentrations”:
Partial Pressure
Molarity
Molar fractions
Each one will have then, its equivalent “Mass Transfer Coefficient”
2 1 2 1
2 1 2 1 2 1
A A A A
A A A A A A
(x x ) (c )
(y ) (c ) (p )
A x L
A y c G
N k k c
N k y k c k p
Note that any way you
calculate, the result must
be the same… WHY?
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website:
187. www.ChemicalEngineeringGuy.com
Proof:
Note that any way you
calculate, the result must
be the same… WHY?
,LM
L
x
B
F
k
x
,LM
G
y
B
F
k
y
2 1 2 1
2 1 2 1 2 1
A A A A
A A A A A A
(x x ) (c )
(y ) (c ) (p )
x L
y c G
k k c
k y k c k p
, ,L L B LM y B LMF k x c k x
, ,
,
B LM B LM
G G B LM c y
p p
F k p k k
RT P
188. www.ChemicalEngineeringGuy.com
Special notes:
Valid mostly for low concentration, i.e. dilute cases
Must be low mass transfer rates due to ignoring the bulk flow velocity
Do you need the Full Version?
Contact me if needed!
Contact@ChemicalEngineeringGuy.com
https://courses.chemicalengineeringguy.com/courses
You can also check out more content here:
My Youtube Channel
My Fan Page
The LinkedIn
My website: