Major project
•Download as PPTX, PDF•
0 likes•12 views
This document describes a home automation system that uses GSM technology and DTMF signaling to control devices remotely using a mobile phone. The system includes a DTMF decoder, logic ICs, transistors, and relays. Pressing buttons on the mobile phone generates DTMF tones that are decoded then used by the logic ICs to activate the relays and control electrical loads such as appliances and robots wirelessly from a distance without needing a separate remote controller.
Report
Share
Report
Share
Recommended
Tele Remote Switch
This document describes a tele remote switch circuit that can remotely control up to 4 devices connected to relay outputs using a telephone's DTMF tones. The circuit uses an AT89C52 microcontroller and MT8870 DTMF decoder chip to detect and decode tones and control the relay outputs. A timer circuit is also described that can be used to set a countdown time to control for how long a connected device remains turned on.
Gsm based home automation
This document describes a GSM based home automation system using DTMF signals. It involves a DTMF decoder, microcontroller, and relays. The system allows controlling electrical devices via mobile phone by sending DTMF tones. When a button on the phone is pressed, the corresponding DTMF tone is decoded by the microcontroller. The microcontroller then activates the necessary relays to control the electrical loads. This allows remote control of appliances and robots through the mobile phone network without needing a separate remote controller.
Intelligent road roller
This document describes an intelligent road roller that uses IR sensors to detect pits in the road. It has two main components:
1. Robo 1 uses IR sensors, a comparator, Arduino, H-bridge and encoder to detect pit holes and transmit the signals via RF link to Robo 2.
2. Robo 2 receives the signals via an RF receiver and decoder connected to a servo motor, DC motor and buzzer. The system allows for real-time monitoring of pit detection on the road surface.
cell phone based device control
This document describes a cell phone based device control project developed under the guidance of Ms. G. Susmitha. The objective is to turn appliances on and off using a cell phone as a remote control. The system allows controlling up to 6 devices and provides voice status updates. It uses components like a microcontroller, DTMF receiver, relay driver, and other basic electronic components. The circuit diagram and working are explained, including interfacing techniques. Advantages, limitations, software used, and future scope are discussed.
cellphone based control of electrical equipment
This document describes a DTMF (Dual Tone Multi-Frequency) based remote control system using a mobile phone. It consists of a DTMF decoder, microcontroller, relays, and appliances. The system allows controlling up to 4 appliances by pressing number keys on the mobile phone. When a key is pressed, the DTMF decoder converts the tones to digital signals for the microcontroller. The microcontroller then activates the corresponding relay to turn the appliance on or off. The system offers remote control of appliances with advantages of quick response, easy operation, and low cost.
DTMF Based speed control of induction motor
This Project presented a method to control speed of induction motor using mobile phone and DTMF decoder. From the convenience of a simple cell phone, a user is able to control and monitor virtually any electrical device. This will be essential because of the wide range of technical knowledge that homeowners have. The popularity and availability of the mobile and mobile network makes this kind of control very useful and powerful. The main advantages of the proposed system are its reliability, low cost, and wide area coverage.
dtmf based mobile control robot
The document summarizes a student project report on developing a remote controlled robotic vehicle using Dual-Tone Multi-Frequency (DTMF) technology. It provides details on the technology used, including the DTMF system and keypad frequencies. It includes circuit diagrams and component lists. It then discusses applications of remote controlled vehicles in scientific research, military, search and rescue, and recreation. It concludes by describing additional features that could be added to improve obstacle detection and security and increase the robot's range of operation.
Remote accident report system for highways using rf
This document describes a remote accident reporting system for highways that uses RF technology. The system aims to monitor accidents on highways and report them. It uses a microcontroller, RF transmitter and receiver, LCD, buzzer, and other components. When an accident is detected by a sensor, the transmitter sends a signal via RF to the receiver. The receiver is connected to a buzzer and LCD to alert authorities and display accident details remotely. The system allows for remote monitoring and control of vehicle accidents on highways.
Recommended
Tele Remote Switch
This document describes a tele remote switch circuit that can remotely control up to 4 devices connected to relay outputs using a telephone's DTMF tones. The circuit uses an AT89C52 microcontroller and MT8870 DTMF decoder chip to detect and decode tones and control the relay outputs. A timer circuit is also described that can be used to set a countdown time to control for how long a connected device remains turned on.
Gsm based home automation
This document describes a GSM based home automation system using DTMF signals. It involves a DTMF decoder, microcontroller, and relays. The system allows controlling electrical devices via mobile phone by sending DTMF tones. When a button on the phone is pressed, the corresponding DTMF tone is decoded by the microcontroller. The microcontroller then activates the necessary relays to control the electrical loads. This allows remote control of appliances and robots through the mobile phone network without needing a separate remote controller.
Intelligent road roller
This document describes an intelligent road roller that uses IR sensors to detect pits in the road. It has two main components:
1. Robo 1 uses IR sensors, a comparator, Arduino, H-bridge and encoder to detect pit holes and transmit the signals via RF link to Robo 2.
2. Robo 2 receives the signals via an RF receiver and decoder connected to a servo motor, DC motor and buzzer. The system allows for real-time monitoring of pit detection on the road surface.
cell phone based device control
This document describes a cell phone based device control project developed under the guidance of Ms. G. Susmitha. The objective is to turn appliances on and off using a cell phone as a remote control. The system allows controlling up to 6 devices and provides voice status updates. It uses components like a microcontroller, DTMF receiver, relay driver, and other basic electronic components. The circuit diagram and working are explained, including interfacing techniques. Advantages, limitations, software used, and future scope are discussed.
cellphone based control of electrical equipment
This document describes a DTMF (Dual Tone Multi-Frequency) based remote control system using a mobile phone. It consists of a DTMF decoder, microcontroller, relays, and appliances. The system allows controlling up to 4 appliances by pressing number keys on the mobile phone. When a key is pressed, the DTMF decoder converts the tones to digital signals for the microcontroller. The microcontroller then activates the corresponding relay to turn the appliance on or off. The system offers remote control of appliances with advantages of quick response, easy operation, and low cost.
DTMF Based speed control of induction motor
This Project presented a method to control speed of induction motor using mobile phone and DTMF decoder. From the convenience of a simple cell phone, a user is able to control and monitor virtually any electrical device. This will be essential because of the wide range of technical knowledge that homeowners have. The popularity and availability of the mobile and mobile network makes this kind of control very useful and powerful. The main advantages of the proposed system are its reliability, low cost, and wide area coverage.
dtmf based mobile control robot
The document summarizes a student project report on developing a remote controlled robotic vehicle using Dual-Tone Multi-Frequency (DTMF) technology. It provides details on the technology used, including the DTMF system and keypad frequencies. It includes circuit diagrams and component lists. It then discusses applications of remote controlled vehicles in scientific research, military, search and rescue, and recreation. It concludes by describing additional features that could be added to improve obstacle detection and security and increase the robot's range of operation.
Remote accident report system for highways using rf
This document describes a remote accident reporting system for highways that uses RF technology. The system aims to monitor accidents on highways and report them. It uses a microcontroller, RF transmitter and receiver, LCD, buzzer, and other components. When an accident is detected by a sensor, the transmitter sends a signal via RF to the receiver. The receiver is connected to a buzzer and LCD to alert authorities and display accident details remotely. The system allows for remote monitoring and control of vehicle accidents on highways.
DTMF based Different Load control
This document describes a DTMF (Dual Tone Multi Frequency) based load control system. The system uses a DTMF decoder interfaced with a microcontroller to receive DTMF tones from a cell phone and control loads remotely. When a key is pressed on the cell phone, the corresponding DTMF tones are received by the decoder and converted to digital codes. The microcontroller then turns relays on/off to actuate loads according to the received commands, allowing remote control of industrial and agricultural equipment or household devices spread over a large area.
Microcontroller remote controlling project
This project aims to remotely control home appliances using a mobile phone. A caller can control appliances by pressing buttons on their phone, generating DTMF tones. These tones are decoded by a microcontroller which then activates relays connected to appliances. The microcontroller was programmed in C to activate relays corresponding to different DTMF tone combinations. This allows remote control of appliances from any phone.
DTMF Mobile Operated Robot using Atmega16
This presentation shows Dual tone multi frequency mobile operated robot.
CVAVR code is also provided....
Project ppt
This document describes a TV remote jammer circuit designed using a Timer IC 555. The circuit works by emitting infrared signals at 38kHz, the operating frequency of most TV remotes, which confuses the TV receiver and prevents the remote from changing channels. The circuit uses components like IR LEDs, a diode, IC 555, potentiometer, battery, resistors and capacitors. The IC 555 is used in astable mode to generate a continuous pulse waveform that drives the IR LEDs. The potentiometer allows tuning the circuit frequency to exactly match the remote. The jammer can block remote control of TV volume and channels but must be tuned correctly to 38kHz.
cellphone based device control
This project involves developing a system to remotely control home appliances using a cellular phone. The system uses a microcontroller and DTMF tones. A caller uses their mobile phone to call a receiver phone located at the control unit. When the call is answered, the caller presses keys to send DTMF tones corresponding to devices they want to control. The tones are decoded and sent to the microcontroller to control appliances. The project was successfully completed and provides a low-cost way to remotely control devices using a mobile phone.
Rutherford 9RCT4331 Data Sheet
Buy the Rutherford 9RCT4331 at JMAC Supply.
https://www.jmac.com/Rutherford_Controls_9RCT4331_p/rutherford-9rct4331.htm?=slideshare
Ppt2 (1)
This document describes a mobile spy robot that uses a wireless webcam. The robot has a pair of laser guns that can be fired remotely, and a wireless camera that sends real-time video and audio to a remote monitor. It uses an ARM processor for control and includes motors, a wireless webcam, DTMF decoder, and other controlled devices. The robot can be controlled remotely to observe an area and take action such as firing lasers as needed.
Hardware required to build a basic Robot
This document provides information about hardware components used in a microcontroller project including an ATmega16 microcontroller, L293D motor driver IC, 7805 voltage regulator, and an AVR development board. It describes the ATmega16 architecture and pin configuration, the functions of the L293D for driving motors, specifications of the 7805 voltage regulator for providing 5V power, and briefly mentions the AVR development board.
Cataloge ge 3.control and_automation_dienhathe.com-4_05_vat300_e_c2-4_rev_b
1) The document provides instructions for wiring the control signal terminal block of a VAT300 drive. Separate the main circuit wiring from other wires and route them separately.
2) Use 0.13 to 0.8mm2 wire for wiring to the control circuit. Tighten terminals TB1 and TB2 with 0.6N·m torque and TB3 with 0.25N·m torque. Keep sequence input/output wires under 30m.
3) The document includes a diagram labeling the terminals of TB1, TB2, TB3, and CN2 as well as notes on dip switch and EL-BIT settings for changing functions like analog input ranges and logic levels.
Ppt2
This document describes a mobile spy robot using a wireless webcam. The robot has a pair of laser guns that can fire remotely and a wireless camera that sends real-time video and audio to a remote monitor. The aim is to capture images from dangerous or difficult to access areas. The hardware includes an ARM microcontroller, DTMF decoder, wireless camera, laser guns, motors, and other components. The robot can be used by the army to identify and attack enemies remotely, allowing human lives to be saved. While expensive and less reliable than humans, it allows combat from a distance.
Traffic signal
Digital Computer Logic Project. Traffic signal using 555 timer and 741790 decade counter IC along with display.
Major
This document summarizes a student project to build a touch-tone telephone robot. It includes sections describing the components used like resistors, capacitors, oscillators, ICs, and a microcontroller. Software tools like ExpressPCB and Keil were used. Potential applications are in scientific, military, and search and rescue operations. The future could include adding a camera, IR sensors, password protection, or an alarm phone dialer. The conclusion is that the project will be beneficial for various purposes.
Vechicle accident prevention using eye bilnk sensor ppt
This document describes a vehicle accident prevention system using an eye blink sensor. The system uses an IR sensor to detect a driver's eye blinks and a microcontroller to process the sensor data. If no eye blinks are detected for a period of time, indicating potential drowsiness, the system will stop the vehicle and trigger an alarm to prevent accidents. The system could also be expanded in the future to detect alcohol and stop the vehicle if the driver is intoxicated.
Home automation control system using dtmf technology
Using This Project we can control our electrical and electronic equipment using mobile phone from any remote location
MICROCONTROLLER BASED IR FOR HOME APPLICATION
This document describes a microcontroller-based infrared (IR) remote control signal decoder designed for home automation applications. It decodes signals from an IR remote to control a fan regulator and power supply switch remotely up to 10 meters away. The device consists of an IR transmitter, IR receiver, microcontroller decoder, and driver circuits. The IR signals are converted to electrical pulses which the microcontroller decodes to control the fan speed or switch power on/off.
DTMF BASED MOBILE CONTROLL ROBOT SYSTEM
This document describes a robot that can be controlled via DTMF tones sent from a mobile phone. The robot has a mobile phone attached that can receive DTMF tones corresponding to buttons pressed on the calling phone. A microcontroller on the robot decodes the tones and controls motors via an H-bridge motor driver to move the robot in different directions. The system allows remote robotic control over large areas using existing mobile networks without interference from other controllers.
Digital electronics
This presentation discusses topics in digital electronics including encoders, half-subtractors, full-subtractors, decoders, multiplexers, de-multiplexers, SR flip-flops, latches and their implementations. It is presented by 6 students whose member IDs are listed. The presentation will cover the differences between encoders and decoders and discuss de-multiplexers as circuits with one input and multiple outputs that can steer any input to a selected output using a control signal.
IEEE PROJECTS ABSTRACT FOR GPS&GSM-Bus automation system using gsm and gps
This project involves automating a bus using GSM and GPS. The bus monitoring system displays the engine temperature, fuel level, and bus location on a centralized display unit. It can also detect accidents using a vibration sensor and send an emergency alert message. The system uses a dsPIC30F4013 microcontroller, GSM modem, GPS receiver, sensors, and other components. It allows the bus to identify its location via GPS and provide stop alerts to passengers.
Advanced motion controls bd40a20
The document describes the BD30A series of brushless servo amplifiers made by Electromate. It provides specifications for four models including peak and continuous current limits, voltage ratings, size, and connector pin functions. The amplifiers are designed to drive brushless DC motors and include protections from overvoltage, overcurrent, and overheating. They interface with digital controllers using PWM and direction inputs.
Advanced motion controls bd40a8
The document describes the BD30A series of brushless servo amplifiers made by Electromate. It provides specifications for four models including peak and continuous current limits, voltage ratings, size, and connector pin functions. The amplifiers are designed to drive brushless DC motors and include protections from overvoltage, overcurrent, and overheating. Current limit and monitoring can be adjusted via DIP switches.
Remote Operated Spy Robot Circuit
The document describes the design and components of a remote-controlled spy robot. It has two main sections: 1) the remote control section, which uses an HT12E encoder and HT12D decoder to control the robot via radio signals from a wireless remote controller. 2) The video transmission section uses a wireless CCD camera powered by a 12V battery to capture video that is transmitted to a remote receiver via radio signals. The robot can be controlled remotely to move forward, backward, left, or right using two 12V gear motors and an L293D motor driver circuit.
DTMF base Mobile controlled appliances control
This document describes a circuit that allows controlling electrical appliances via a mobile phone using DTMF tones. The circuit uses a DTMF decoder IC to decode the tones from the phone's microphone into digital outputs. These outputs control a relay circuit that can power appliances. When a key is pressed on the phone, the DTMF IC detects the tone and triggers a flip-flop that energizes the relay and the appliance. This allows remote control of devices from a phone without needing an internet connection.
More Related Content
What's hot
DTMF based Different Load control
This document describes a DTMF (Dual Tone Multi Frequency) based load control system. The system uses a DTMF decoder interfaced with a microcontroller to receive DTMF tones from a cell phone and control loads remotely. When a key is pressed on the cell phone, the corresponding DTMF tones are received by the decoder and converted to digital codes. The microcontroller then turns relays on/off to actuate loads according to the received commands, allowing remote control of industrial and agricultural equipment or household devices spread over a large area.
Microcontroller remote controlling project
This project aims to remotely control home appliances using a mobile phone. A caller can control appliances by pressing buttons on their phone, generating DTMF tones. These tones are decoded by a microcontroller which then activates relays connected to appliances. The microcontroller was programmed in C to activate relays corresponding to different DTMF tone combinations. This allows remote control of appliances from any phone.
DTMF Mobile Operated Robot using Atmega16
This presentation shows Dual tone multi frequency mobile operated robot.
CVAVR code is also provided....
Project ppt
This document describes a TV remote jammer circuit designed using a Timer IC 555. The circuit works by emitting infrared signals at 38kHz, the operating frequency of most TV remotes, which confuses the TV receiver and prevents the remote from changing channels. The circuit uses components like IR LEDs, a diode, IC 555, potentiometer, battery, resistors and capacitors. The IC 555 is used in astable mode to generate a continuous pulse waveform that drives the IR LEDs. The potentiometer allows tuning the circuit frequency to exactly match the remote. The jammer can block remote control of TV volume and channels but must be tuned correctly to 38kHz.
cellphone based device control
This project involves developing a system to remotely control home appliances using a cellular phone. The system uses a microcontroller and DTMF tones. A caller uses their mobile phone to call a receiver phone located at the control unit. When the call is answered, the caller presses keys to send DTMF tones corresponding to devices they want to control. The tones are decoded and sent to the microcontroller to control appliances. The project was successfully completed and provides a low-cost way to remotely control devices using a mobile phone.
Rutherford 9RCT4331 Data Sheet
Buy the Rutherford 9RCT4331 at JMAC Supply.
https://www.jmac.com/Rutherford_Controls_9RCT4331_p/rutherford-9rct4331.htm?=slideshare
Ppt2 (1)
This document describes a mobile spy robot that uses a wireless webcam. The robot has a pair of laser guns that can be fired remotely, and a wireless camera that sends real-time video and audio to a remote monitor. It uses an ARM processor for control and includes motors, a wireless webcam, DTMF decoder, and other controlled devices. The robot can be controlled remotely to observe an area and take action such as firing lasers as needed.
Hardware required to build a basic Robot
This document provides information about hardware components used in a microcontroller project including an ATmega16 microcontroller, L293D motor driver IC, 7805 voltage regulator, and an AVR development board. It describes the ATmega16 architecture and pin configuration, the functions of the L293D for driving motors, specifications of the 7805 voltage regulator for providing 5V power, and briefly mentions the AVR development board.
Cataloge ge 3.control and_automation_dienhathe.com-4_05_vat300_e_c2-4_rev_b
1) The document provides instructions for wiring the control signal terminal block of a VAT300 drive. Separate the main circuit wiring from other wires and route them separately.
2) Use 0.13 to 0.8mm2 wire for wiring to the control circuit. Tighten terminals TB1 and TB2 with 0.6N·m torque and TB3 with 0.25N·m torque. Keep sequence input/output wires under 30m.
3) The document includes a diagram labeling the terminals of TB1, TB2, TB3, and CN2 as well as notes on dip switch and EL-BIT settings for changing functions like analog input ranges and logic levels.
Ppt2
This document describes a mobile spy robot using a wireless webcam. The robot has a pair of laser guns that can fire remotely and a wireless camera that sends real-time video and audio to a remote monitor. The aim is to capture images from dangerous or difficult to access areas. The hardware includes an ARM microcontroller, DTMF decoder, wireless camera, laser guns, motors, and other components. The robot can be used by the army to identify and attack enemies remotely, allowing human lives to be saved. While expensive and less reliable than humans, it allows combat from a distance.
Traffic signal
Digital Computer Logic Project. Traffic signal using 555 timer and 741790 decade counter IC along with display.
Major
This document summarizes a student project to build a touch-tone telephone robot. It includes sections describing the components used like resistors, capacitors, oscillators, ICs, and a microcontroller. Software tools like ExpressPCB and Keil were used. Potential applications are in scientific, military, and search and rescue operations. The future could include adding a camera, IR sensors, password protection, or an alarm phone dialer. The conclusion is that the project will be beneficial for various purposes.
Vechicle accident prevention using eye bilnk sensor ppt
This document describes a vehicle accident prevention system using an eye blink sensor. The system uses an IR sensor to detect a driver's eye blinks and a microcontroller to process the sensor data. If no eye blinks are detected for a period of time, indicating potential drowsiness, the system will stop the vehicle and trigger an alarm to prevent accidents. The system could also be expanded in the future to detect alcohol and stop the vehicle if the driver is intoxicated.
Home automation control system using dtmf technology
Using This Project we can control our electrical and electronic equipment using mobile phone from any remote location
MICROCONTROLLER BASED IR FOR HOME APPLICATION
This document describes a microcontroller-based infrared (IR) remote control signal decoder designed for home automation applications. It decodes signals from an IR remote to control a fan regulator and power supply switch remotely up to 10 meters away. The device consists of an IR transmitter, IR receiver, microcontroller decoder, and driver circuits. The IR signals are converted to electrical pulses which the microcontroller decodes to control the fan speed or switch power on/off.
DTMF BASED MOBILE CONTROLL ROBOT SYSTEM
This document describes a robot that can be controlled via DTMF tones sent from a mobile phone. The robot has a mobile phone attached that can receive DTMF tones corresponding to buttons pressed on the calling phone. A microcontroller on the robot decodes the tones and controls motors via an H-bridge motor driver to move the robot in different directions. The system allows remote robotic control over large areas using existing mobile networks without interference from other controllers.
Digital electronics
This presentation discusses topics in digital electronics including encoders, half-subtractors, full-subtractors, decoders, multiplexers, de-multiplexers, SR flip-flops, latches and their implementations. It is presented by 6 students whose member IDs are listed. The presentation will cover the differences between encoders and decoders and discuss de-multiplexers as circuits with one input and multiple outputs that can steer any input to a selected output using a control signal.
IEEE PROJECTS ABSTRACT FOR GPS&GSM-Bus automation system using gsm and gps
This project involves automating a bus using GSM and GPS. The bus monitoring system displays the engine temperature, fuel level, and bus location on a centralized display unit. It can also detect accidents using a vibration sensor and send an emergency alert message. The system uses a dsPIC30F4013 microcontroller, GSM modem, GPS receiver, sensors, and other components. It allows the bus to identify its location via GPS and provide stop alerts to passengers.
Advanced motion controls bd40a20
The document describes the BD30A series of brushless servo amplifiers made by Electromate. It provides specifications for four models including peak and continuous current limits, voltage ratings, size, and connector pin functions. The amplifiers are designed to drive brushless DC motors and include protections from overvoltage, overcurrent, and overheating. They interface with digital controllers using PWM and direction inputs.
Advanced motion controls bd40a8
The document describes the BD30A series of brushless servo amplifiers made by Electromate. It provides specifications for four models including peak and continuous current limits, voltage ratings, size, and connector pin functions. The amplifiers are designed to drive brushless DC motors and include protections from overvoltage, overcurrent, and overheating. Current limit and monitoring can be adjusted via DIP switches.
What's hot (20)
Cataloge ge 3.control and_automation_dienhathe.com-4_05_vat300_e_c2-4_rev_b
Cataloge ge 3.control and_automation_dienhathe.com-4_05_vat300_e_c2-4_rev_b
Vechicle accident prevention using eye bilnk sensor ppt
Vechicle accident prevention using eye bilnk sensor ppt
Home automation control system using dtmf technology
Home automation control system using dtmf technology
IEEE PROJECTS ABSTRACT FOR GPS&GSM-Bus automation system using gsm and gps
IEEE PROJECTS ABSTRACT FOR GPS&GSM-Bus automation system using gsm and gps
Similar to Major project
Remote Operated Spy Robot Circuit
The document describes the design and components of a remote-controlled spy robot. It has two main sections: 1) the remote control section, which uses an HT12E encoder and HT12D decoder to control the robot via radio signals from a wireless remote controller. 2) The video transmission section uses a wireless CCD camera powered by a 12V battery to capture video that is transmitted to a remote receiver via radio signals. The robot can be controlled remotely to move forward, backward, left, or right using two 12V gear motors and an L293D motor driver circuit.
DTMF base Mobile controlled appliances control
This document describes a circuit that allows controlling electrical appliances via a mobile phone using DTMF tones. The circuit uses a DTMF decoder IC to decode the tones from the phone's microphone into digital outputs. These outputs control a relay circuit that can power appliances. When a key is pressed on the phone, the DTMF IC detects the tone and triggers a flip-flop that energizes the relay and the appliance. This allows remote control of devices from a phone without needing an internet connection.
home appliance control using gsm
This document describes a student project to create a remote home appliance control system using a microcontroller, GSM modem, and SMS messages. The system allows users to control devices like lights and fans from anywhere via a mobile phone. It aims to provide a low-cost alternative to existing wireless home automation technologies. The document outlines the project objectives, hardware components, software, applications, advantages, and conclusions.
Auto dial-er Home security
This document is a project report submitted to Rajasthan Technical University for a Bachelor of Technology degree. It outlines the design of an auto dialer home security system using a microcontroller, GSM modem, and sensors. The system is designed to detect intruders or fires using infrared and fire sensors, and then send an SMS alert to a user's phone number through the GSM modem. The report describes the basic design criteria, components used including the AT89C2051 microcontroller and GSM modem interface, and sensor modules for infrared and fire detection.
GSM CONTROL OF ELECTRICAL APPLIANCES
- This paper shows an approach for designing a
system which implement a microcontroller-based control module
that receives its instructions and commands from a cellular phone
over the GSM (Global system for mobile communication)
network. The microcontroller then will carry out the issued
commands and then communicate the status of a given appliance
or device back to the cellular phone.This device allows a user to
remotely control and monitor multiple home/office appliances
using a cellular phone. This system will be a powerful and flexible
tool that will offer this service at any time, and from anywhere
that has network coverage. Due to the fact that the combination
and sequential logic circuits have more components soldered
together, inflexible, more difficult to the user, and not
programmable, the 8951 micro controller was chosen because it
can be written to and read from and also has an internal memory
which makes it to be versatile in application and user
friendly. Apart from the micro controller, other electrical /
electronic components used include: resistors, filters, voltage
regulator, transformer, rectifiers, capacitors, DTMF (Dual Tone
Multi Frequency) Integrated circuit etc.
final ppt2.pptx
This document describes a project to remotely control a land rover vehicle using DTMF tones generated from a mobile phone. DTMF signals from the phone are decoded using an 8870 IC and sent to an AT89S52 microcontroller. The microcontroller then controls an L293D motor driver and four motors on the rover to move it forward, backward, left and right. Potential applications include remote control vehicles for scientific, military, and search and rescue purposes. Further improvements could involve adding sensors to detect obstacles and a camera for beyond line-of-sight control.
DTMF based home automation with ADRUINO
This document provides an overview of a project to develop a home automation system using Dual Tone Multi Frequency (DTMF) technology paired with wireless communication. Chapter 1 introduces DTMF technology and its use in telephone signaling. Chapter 2 discusses implementing the system using an Arduino Uno microcontroller and a DTMF decoder chip. It also describes using relays and a relay driver chip to control appliances. Chapter 3 states the problem is to allow remote control and monitoring of home appliances by cellular phone from anywhere.
DTMF CONTROLLED ROBOT
This document describes a wireless controlled robot using DTMF tones and a microcontroller. The robot can be controlled from a mobile phone by pressing buttons which are decoded by a DTMF receiver and sent to the microcontroller. The microcontroller then controls the motor driver and motors to move the robot in the corresponding directions. Potential applications include military, law enforcement, search and rescue, and home automation. The design could be improved in the future by adding sensors, password protection, camera, and alarm functions.
cellphone detector
What it is: This is a circuit for a mobile transmission detector which can detect use of a mobile phone within the range of 1.5 meters. Whenever usage of mobile phone is detected such as calling or texting a beep alarm starts sounding and a led blinks.
Why it is: This handy, pocket-size mobile transmission detector can sense the presence of an activated mobile phone from a distance of one and a-half meters.
Where it is used: it can be used to prevent use of mobile phones in examination halls, confidential rooms, etc. It is also useful for detecting the use of mobile phone for spying and unauthorized video transmission.
mobile bug
This document describes a circuit for detecting mobile phone transmissions within a range of 1.5 meters. The circuit uses a 0.22uF capacitor to capture radio frequency signals from an activated mobile phone. The captured signals are converted to a voltage by an op-amp IC, triggering a buzzer and LED to alert of phone usage. The circuit can detect calls, texts and video transmissions from phones, even on silent mode. It has potential applications to prevent phone use in secure areas like exam halls. Future work could aim to increase the detection range.
Electricity theft control
GSM based electricity theft control system that intimates through message when slightest action for theft is made and also sends us message about the unit consumed.
Electricity theft control
GSM based electricity theft contol system, it also intimates the concernded person when theft is happening. It sends messages about the unit consumed too.
Voice recognition based home automation system for paralyzed people
Automation is a trending topic in 21st century making an important role in our daily lives. Automation reduces the human labor, time, effort and some human errors. The key objective of our project is to design a system for physically handicapped persons to control and operate home appliances and their own wheel chair by their own voice. Both these qualities are present in our project which has the capability to replace existing technologies. the design of the low cost voice recognition based home automation system for the physically challenged people suffering from quadriplegia or paraplegia (who cannot move their limbs but can speak and listen) to control the various home appliances just by his/her voice commands according to their need and comfort. We also implemented a messaging concept. In this whenever the patient or the person needs a help, if he/she pronounce as help a message will be sent to their respective represented family member. The resultant system can provide a great assistance to the physically handicapped people without any need of third person.
Gps vehicle theft identification and tracking and control
This document describes a microcontroller-based GPS and GSM tracking system. It includes a block diagram showing the main components: a microcontroller, GPS modem, GSM modem, LCD display, sensor, ADC and power supply. It provides details on the 8051 microcontroller, MEMS sensors, and the importance of GPS and GSM networks for location tracking. It also lists advantages like security, remote access and applications in vehicles, ships and tracking systems.
QSFP28-100G-LR4-T01#111004.pdf
This document specifies the technical details of a 100G LR4 1310nm 10km QSFP28 transceiver module made by Guilin GLsun Science and Tech Group Co., LTD. It includes details on the product features, optical and electrical characteristics, pin descriptions, mechanical specifications, EEPROM memory map, digital diagnostic monitoring interface, and ordering information. The transceiver module supports 4 independent full-duplex channels up to 25Gbps per wavelength and has a link length up to 10km. It complies with various industry standards and has features such as hot-pluggability and a QSFP28 footprint.
qsfp28-100g-lr4-1310nm-10km-transceiver-module-111004.pdf
This document specifies the technical details of a 100G LR4 1310nm 10km QSFP28 transceiver module made by Guilin GLsun Science and Tech Group Co., LTD. It includes details on the product features, optical and electrical characteristics, pin descriptions, mechanical specifications, EEPROM memory map, digital diagnostic monitoring interface, and ordering information. The transceiver module supports 4 independent full-duplex channels up to 25Gbps per wavelength and has a link length up to 10km. It complies with various industry standards and has features such as hot-pluggability and a QSFP28 footprint.
QSFP28-100G-LR4-T01#111004.pdf
This document specifies the technical details of a 100G LR4 1310nm 10km QSFP28 transceiver module made by Guilin GLsun Science and Tech Group Co., LTD. It includes details on the product features, optical and electrical characteristics, pin descriptions, mechanical specifications, EEPROM memory map, digital diagnostic monitoring interface, and ordering information. The transceiver module supports 4 independent full-duplex channels up to 25Gbps per wavelength and has a link length up to 10km. It complies with various industry standards and has features such as hot-pluggability and a QSFP28 footprint.
fault detection of transformer using GSM,,,,by YASASWINI.KAGITHALA
This document describes a project to design a fault recognition protection system for AC transmission lines using GSM technology. The system monitors the output of a step-down transformer using a microcontroller and fault indicator circuit. If a fault is detected, a relay is activated and a message is sent via GSM modem to notify the user. The system is powered by a regulated 5V supply and includes components like a LCD to display the power line status, buzzer to sound on fault, and MAX232 for serial communication between the microcontroller and GSM modem. The aim is to remotely monitor transformer faults without needing to check relays on site.
KAGITHALA YASASWINI
This document describes a project to design a fault recognition protection system for AC transmission lines using GSM technology. The system monitors the output of a step-down transformer using a microcontroller and fault indicator circuit. If a fault is detected, a relay is activated and a message is sent via GSM modem to notify the user. The system provides remote monitoring of power grids to reduce outage times and notify maintenance crews immediately in case of a fault. Key components include a power supply, fault indicator, microcontroller, LCD display, relay, buzzer, GSM modem and supporting circuits.
Smart agriculture system using IOT
This document describes an IoT project using an Arduino Uno, GSM shield, and relay to remotely control a water pump via mobile phone. The system allows farmers to turn a water pump on and off from anywhere using an AT command text message to the GSM shield. Key hardware includes the Arduino for control logic, GSM shield for cellular connectivity, and relay to switch the water pump power. The system aims to help farmers remotely operate water pumps for irrigation from off-site locations using a mobile phone.
Similar to Major project (20)
Voice recognition based home automation system for paralyzed people
Voice recognition based home automation system for paralyzed people
Gps vehicle theft identification and tracking and control
Gps vehicle theft identification and tracking and control
qsfp28-100g-lr4-1310nm-10km-transceiver-module-111004.pdf
qsfp28-100g-lr4-1310nm-10km-transceiver-module-111004.pdf
fault detection of transformer using GSM,,,,by YASASWINI.KAGITHALA
fault detection of transformer using GSM,,,,by YASASWINI.KAGITHALA
Recently uploaded
官方认证美国密歇根州立大学毕业证学位证书原版一模一样
原版一模一样【微信：741003700 】【美国密歇根州立大学毕业证学位证书】【微信：741003700 】学位证，留信认证（真实可查，永久存档）offer、雅思、外壳等材料/诚信可靠,可直接看成品样本，帮您解决无法毕业带来的各种难题！外壳，原版制作，诚信可靠，可直接看成品样本。行业标杆！精益求精，诚心合作，真诚制作！多年品质 ,按需精细制作，24小时接单,全套进口原装设备。十五年致力于帮助留学生解决难题，包您满意。
本公司拥有海外各大学样板无数，能完美还原海外各大学 Bachelor Diploma degree, Master Degree Diploma
1:1完美还原海外各大学毕业材料上的工艺：水印，阴影底纹，钢印LOGO烫金烫银，LOGO烫金烫银复合重叠。文字图案浮雕、激光镭射、紫外荧光、温感、复印防伪等防伪工艺。材料咨询办理、认证咨询办理请加学历顾问Q/微741003700
留信网认证的作用:
1:该专业认证可证明留学生真实身份
2:同时对留学生所学专业登记给予评定
3:国家专业人才认证中心颁发入库证书
4:这个认证书并且可以归档倒地方
5:凡事获得留信网入网的信息将会逐步更新到个人身份内，将在公安局网内查询个人身份证信息后，同步读取人才网入库信息
6:个人职称评审加20分
7:个人信誉贷款加10分
8:在国家人才网主办的国家网络招聘大会中纳入资料，供国家高端企业选择人才
一比一原版(CalArts毕业证)加利福尼亚艺术学院毕业证如何办理
CalArts毕业证学历书【微信95270640】CalArts毕业证’圣力嘉学院毕业证《Q微信95270640》办理CalArts毕业证√文凭学历制作{CalArts文凭}购买学历学位证书本科硕士,CalArts毕业证学历学位证【实体公司】办毕业证、成绩单、学历认证、学位证、文凭认证、办留信网认证、（网上可查，实体公司，专业可靠）
(诚招代理)办理国外高校毕业证成绩单文凭学位证,真实使馆公证（留学回国人员证明）真实留信网认证国外学历学位认证雅思代考国外学校代申请名校保录开请假条改GPA改成绩ID卡
1.高仿业务:【本科硕士】毕业证,成绩单（GPA修改）,学历认证（教育部认证）,大学Offer,,ID,留信认证,使馆认证,雅思,语言证书等高仿类证书；
2.认证服务: 学历认证（教育部认证）,大使馆认证（回国人员证明）,留信认证（可查有编号证书）,大学保录取,雅思保分成绩单。
3.技术服务：钢印水印烫金激光防伪凹凸版设计印刷激凸温感光标底纹镭射速度快。
办理加利福尼亚艺术学院加利福尼亚艺术学院毕业证文凭证书流程：
1客户提供办理信息：姓名生日专业学位毕业时间等（如信息不确定可以咨询顾问：我们有专业老师帮你查询）；
2开始安排制作毕业证成绩单电子图；
3毕业证成绩单电子版做好以后发送给您确认；
4毕业证成绩单电子版您确认信息无误之后安排制作成品；
5成品做好拍照或者视频给您确认；
6快递给客户（国内顺丰国外DHLUPS等快读邮寄）
-办理真实使馆公证（即留学回国人员证明）
-办理各国各大学文凭（世界名校一对一专业服务,可全程监控跟踪进度）
-全套服务：毕业证成绩单真实使馆公证真实教育部认证。让您回国发展信心十足！
（详情请加一下 文凭顾问+微信:95270640）欢迎咨询！子小伍玩小伍比山娃小一岁虎头虎脑的很霸气父亲让山娃跟小伍去夏令营听课山娃很高兴夏令营就设在附近一所小学山娃发现那所小学比自己的学校更大更美操场上还铺有塑胶跑道呢里面很多小朋友一班一班的快快乐乐原来城里娃都藏这儿来了怪不得平时见不到他们山娃恍然大悟起来吹拉弹唱琴棋书画山娃都不懂却什么都想学山娃怨自己太笨什么都不会斟酌再三山娃终于选定了学美术当听说每月要交元时父亲犹豫了山娃也说爸算了吧咱学校一学期才转
Applications of artificial Intelligence in Mechanical Engineering.pdf
Historically, mechanical engineering has relied heavily on human expertise and empirical methods to solve complex problems. With the introduction of computer-aided design (CAD) and finite element analysis (FEA), the field took its first steps towards digitization. These tools allowed engineers to simulate and analyze mechanical systems with greater accuracy and efficiency. However, the sheer volume of data generated by modern engineering systems and the increasing complexity of these systems have necessitated more advanced analytical tools, paving the way for AI.
AI offers the capability to process vast amounts of data, identify patterns, and make predictions with a level of speed and accuracy unattainable by traditional methods. This has profound implications for mechanical engineering, enabling more efficient design processes, predictive maintenance strategies, and optimized manufacturing operations. AI-driven tools can learn from historical data, adapt to new information, and continuously improve their performance, making them invaluable in tackling the multifaceted challenges of modern mechanical engineering.
原版制作(Humboldt毕业证书)柏林大学毕业证学位证一模一样
原件一模一样【微信：bwp0011】《(Humboldt毕业证书)柏林大学毕业证学位证》【微信：bwp0011】学位证，留信认证（真实可查，永久存档）原件一模一样纸张工艺/offer、雅思、外壳等材料/诚信可靠,可直接看成品样本，帮您解决无法毕业带来的各种难题！外壳，原版制作，诚信可靠，可直接看成品样本。行业标杆！精益求精，诚心合作，真诚制作！多年品质 ,按需精细制作，24小时接单,全套进口原装设备。十五年致力于帮助留学生解决难题，包您满意。
本公司拥有海外各大学样板无数，能完美还原。
1:1完美还原海外各大学毕业材料上的工艺：水印，阴影底纹，钢印LOGO烫金烫银，LOGO烫金烫银复合重叠。文字图案浮雕、激光镭射、紫外荧光、温感、复印防伪等防伪工艺。材料咨询办理、认证咨询办理请加学历顾问微bwp0011
【主营项目】
一.毕业证【微bwp0011】成绩单、使馆认证、教育部认证、雅思托福成绩单、学生卡等！
二.真实使馆公证(即留学回国人员证明,不成功不收费)
三.真实教育部学历学位认证（教育部存档！教育部留服网站永久可查）
四.办理各国各大学文凭(一对一专业服务,可全程监控跟踪进度)
如果您处于以下几种情况：
◇在校期间，因各种原因未能顺利毕业……拿不到官方毕业证【微bwp0011】
◇面对父母的压力，希望尽快拿到；
◇不清楚认证流程以及材料该如何准备；
◇回国时间很长，忘记办理；
◇回国马上就要找工作，办给用人单位看；
◇企事业单位必须要求办理的
◇需要报考公务员、购买免税车、落转户口
◇申请留学生创业基金
留信网认证的作用:
1:该专业认证可证明留学生真实身份
2:同时对留学生所学专业登记给予评定
3:国家专业人才认证中心颁发入库证书
4:这个认证书并且可以归档倒地方
5:凡事获得留信网入网的信息将会逐步更新到个人身份内，将在公安局网内查询个人身份证信息后，同步读取人才网入库信息
6:个人职称评审加20分
7:个人信誉贷款加10分
8:在国家人才网主办的国家网络招聘大会中纳入资料，供国家高端企业选择人才
Mechanical Engineering on AAI Summer Training Report-003.pdf
Mechanical Engineering PROJECT REPORT ON SUMMER VOCATIONAL TRAINING
AT MBB AIRPORT
22CYT12-Unit-V-E Waste and its Management.ppt
Introduction- e - waste – definition - sources of e-waste– hazardous substances in e-waste - effects of e-waste on environment and human health- need for e-waste management– e-waste handling rules - waste minimization techniques for managing e-waste – recycling of e-waste - disposal treatment methods of e- waste – mechanism of extraction of precious metal from leaching solution-global Scenario of E-waste – E-waste in India- case studies.
学校原版美国波士顿大学毕业证学历学位证书原版一模一样
原版一模一样【微信：741003700 】【美国波士顿大学毕业证学历学位证书】【微信：741003700 】学位证，留信认证（真实可查，永久存档）offer、雅思、外壳等材料/诚信可靠,可直接看成品样本，帮您解决无法毕业带来的各种难题！外壳，原版制作，诚信可靠，可直接看成品样本。行业标杆！精益求精，诚心合作，真诚制作！多年品质 ,按需精细制作，24小时接单,全套进口原装设备。十五年致力于帮助留学生解决难题，包您满意。
本公司拥有海外各大学样板无数，能完美还原海外各大学 Bachelor Diploma degree, Master Degree Diploma
1:1完美还原海外各大学毕业材料上的工艺：水印，阴影底纹，钢印LOGO烫金烫银，LOGO烫金烫银复合重叠。文字图案浮雕、激光镭射、紫外荧光、温感、复印防伪等防伪工艺。材料咨询办理、认证咨询办理请加学历顾问Q/微741003700
留信网认证的作用:
1:该专业认证可证明留学生真实身份
2:同时对留学生所学专业登记给予评定
3:国家专业人才认证中心颁发入库证书
4:这个认证书并且可以归档倒地方
5:凡事获得留信网入网的信息将会逐步更新到个人身份内，将在公安局网内查询个人身份证信息后，同步读取人才网入库信息
6:个人职称评审加20分
7:个人信誉贷款加10分
8:在国家人才网主办的国家网络招聘大会中纳入资料，供国家高端企业选择人才
Electric vehicle and photovoltaic advanced roles in enhancing the financial p...
Climate change's impact on the planet forced the United Nations and governments to promote green energies and electric transportation. The deployments of photovoltaic (PV) and electric vehicle (EV) systems gained stronger momentum due to their numerous advantages over fossil fuel types. The advantages go beyond sustainability to reach financial support and stability. The work in this paper introduces the hybrid system between PV and EV to support industrial and commercial plants. This paper covers the theoretical framework of the proposed hybrid system including the required equation to complete the cost analysis when PV and EV are present. In addition, the proposed design diagram which sets the priorities and requirements of the system is presented. The proposed approach allows setup to advance their power stability, especially during power outages. The presented information supports researchers and plant owners to complete the necessary analysis while promoting the deployment of clean energy. The result of a case study that represents a dairy milk farmer supports the theoretical works and highlights its advanced benefits to existing plants. The short return on investment of the proposed approach supports the paper's novelty approach for the sustainable electrical system. In addition, the proposed system allows for an isolated power setup without the need for a transmission line which enhances the safety of the electrical network
Rainfall intensity duration frequency curve statistical analysis and modeling...
Using data from 41 years in Patna’ India’ the study’s goal is to analyze the trends of how often it rains on a weekly, seasonal, and annual basis (1981−2020). First, utilizing the intensity-duration-frequency (IDF) curve and the relationship by statistically analyzing rainfall’ the historical rainfall data set for Patna’ India’ during a 41 year period (1981−2020), was evaluated for its quality. Changes in the hydrologic cycle as a result of increased greenhouse gas emissions are expected to induce variations in the intensity, length, and frequency of precipitation events. One strategy to lessen vulnerability is to quantify probable changes and adapt to them. Techniques such as log-normal, normal, and Gumbel are used (EV-I). Distributions were created with durations of 1, 2, 3, 6, and 24 h and return times of 2, 5, 10, 25, and 100 years. There were also mathematical correlations discovered between rainfall and recurrence interval.
Findings: Based on findings, the Gumbel approach produced the highest intensity values, whereas the other approaches produced values that were close to each other. The data indicates that 461.9 mm of rain fell during the monsoon season’s 301st week. However, it was found that the 29th week had the greatest average rainfall, 92.6 mm. With 952.6 mm on average, the monsoon season saw the highest rainfall. Calculations revealed that the yearly rainfall averaged 1171.1 mm. Using Weibull’s method, the study was subsequently expanded to examine rainfall distribution at different recurrence intervals of 2, 5, 10, and 25 years. Rainfall and recurrence interval mathematical correlations were also developed. Further regression analysis revealed that short wave irrigation, wind direction, wind speed, pressure, relative humidity, and temperature all had a substantial influence on rainfall.
Originality and value: The results of the rainfall IDF curves can provide useful information to policymakers in making appropriate decisions in managing and minimizing floods in the study area.
Recently uploaded (20)
Manufacturing Process of molasses based distillery ppt.pptx
Manufacturing Process of molasses based distillery ppt.pptx
Engineering Drawings Lecture Detail Drawings 2014.pdf
Engineering Drawings Lecture Detail Drawings 2014.pdf
Applications of artificial Intelligence in Mechanical Engineering.pdf
Applications of artificial Intelligence in Mechanical Engineering.pdf
Mechanical Engineering on AAI Summer Training Report-003.pdf
Mechanical Engineering on AAI Summer Training Report-003.pdf
Generative AI leverages algorithms to create various forms of content
Generative AI leverages algorithms to create various forms of content
Electric vehicle and photovoltaic advanced roles in enhancing the financial p...
Electric vehicle and photovoltaic advanced roles in enhancing the financial p...
Rainfall intensity duration frequency curve statistical analysis and modeling...
Rainfall intensity duration frequency curve statistical analysis and modeling...
Major project
- 1. GSM based Home Automation PRIYANKA SHARMA- 1301214063 MONIKA KUMARI - 1301214083 NIRAJ KUMAR - 1301214178 1
- 2. GSM DTMF DTMF DECODER LOGIC IC(AND & NOT) TRANSISTORS RELAYS COMPLETE CIRCUIT 2
- 3. Now a days , GSM services easily available to everyone . And You need not to carry a different remote controller . Mobile Stations are already a multipurpose devices , so why not to incorporate one more 3
- 4. Dual-tone multi-frequency signalling (DTMF) is used for telecommunication signalling Between telephone handsets and other communications devices and the switching centre . 4 1209 Hz 1336 Hz 1477 Hz 697 Hz 1 2 3 770 Hz 4 5 6 852 Hz 7 8 9 941 Hz * 0 #
- 5. 5
- 7. 7 4 input AND Gate 4 input AND Gate 4 input AND Gate Latch 1 Latch 2 Latch 3 Load A Load B Load C A A B B C C D D Logic Parallel Lines MT8870 DTMF Decoder
- 8. 8
- 9. Problem : The output of Logic IC is of very low power highly insufficient to operate electrical loads . So we use relays for controlling electrical heavy loads through Logic IC . 9
- 10. 10 AC POWER
- 12. Remote controlled ROBOTS and APPLICANCES 12
- 13. No feedback GSM connection for the operation 13
- 14. 14