This document describes a hardware model for generating electricity from the kinetic energy of vehicles passing over speed bumps. The model uses a rack and pinion mechanism to convert the up-and-down motion of the speed bump into rotational motion. This rotation is amplified through a system of sprockets and chains connected to a flywheel and generator. Calculations estimate that a single vehicle passing could generate approximately 3 watts of power. Over an hour and day, this setup could produce enough energy to power streetlights or other small loads. The design aims to harness wasted kinetic energy from vehicles to generate renewable electricity without dependence on other factors.
The International Journal of Engineering and Science (The IJES)theijes
The International Journal of Engineering & Science is aimed at providing a platform for researchers, engineers, scientists, or educators to publish their original research results, to exchange new ideas, to disseminate information in innovative designs, engineering experiences and technological skills. It is also the Journal's objective to promote engineering and technology education. All papers submitted to the Journal will be blind peer-reviewed. Only original articles will be published.
The papers for publication in The International Journal of Engineering& Science are selected through rigorous peer reviews to ensure originality, timeliness, relevance, and readability.
The International Journal of Engineering and Science (The IJES)theijes
The International Journal of Engineering & Science is aimed at providing a platform for researchers, engineers, scientists, or educators to publish their original research results, to exchange new ideas, to disseminate information in innovative designs, engineering experiences and technological skills. It is also the Journal's objective to promote engineering and technology education. All papers submitted to the Journal will be blind peer-reviewed. Only original articles will be published.
The papers for publication in The International Journal of Engineering& Science are selected through rigorous peer reviews to ensure originality, timeliness, relevance, and readability.
Free Powered Electric Vehicle_Designed by Pranav NavathePranavNavathe
In today’s world the rapid growth in automobile industry requested most accurate and high
performable vehicles, with pollution free and low cost in operation. The project free powered electric
vehicle is an automobile which works on the principle of generating electricity with the help of
synchronous electric motor and generator with attached fly wheel, boosting circuit which acts as a
free powering machine by restoring waste mechanical energy into useful electric work. This device
consists of one electric motor and generator with attached fly wheel in centre so that it connected
with motor and generator with belt pulleys. When an mechanical input is given to the generator with
help of stator its produces electricity later which is passed to motor as input so, motor rotates the
attached flywheel then the stored kinetic energy in the flywheel is utilized to multiply the rotations of
generator shaft to produce electricity with little effort on motor in this way cycle repeated and from
produced electricity some amount of electricity taken as output which is used for charging batteries,
accessories of the electric vehicle. Such that vehicle is propelled.
Power Generation from Speed Breaker Using Crank ShaftIJARTES
Power Generation from Speed Breaker Using
Crank Shaft
This paper attempts to show how energy can
tapped and used at a commonly used system the load speed
breaker. As the demand of electric power is increasing day-byday
for the working of various appliances. Producing
electricity from various sources is needed like from a speed
breaker is a new concept that is an undergoing research. The
number of vehicles on road is increase rapidly and if we
convert some of the kinetic energy of this vehicle into
rotational motion of roller then we can produce considerable
amount of electricity. The demand of the hour is to have some
source of green energy which can be produce with less (or) no
harmful by-products. Our project is to develop an alternative
green source of energy by moving vehicles on the road ways
While moving, the vehicles possess some kinetic energy and it is being wasted. This kinetic energy can be utilized to produce power by using a special arrangement called POWER HUMP (SPEED BREAKER
In a world where environment protection and energy conversion are growing concerns,the development of solar vehicle has taken on an accele ration pace. The dream of having commercially viable solar vehicle is becoming a rea lity. EV�s are gradually available in the market. This opportunity is taken towards design an d development of Solar two wheeler. Solar vehicle is a multi-disciplinary subject which covers broad and complex aspects. However,it has core technologies,namely propulsio n technology,energy source technology,storage and control technology. As energy source s olar panel is used and developed voltage is stored in battery and used for the drive the hub motor which is used as rare wheel of the vehicle.
Design, development and performance evaluation of solar power assisted tricycleeSAT Journals
Abstract Solar energy is the only source of renewable energy which can be a feasible alternative for fossil fuels. In this work, a solar powered cycle is fabricated by modifying a all geared bicycle. The discussion covers the design, assembly and performance evaluation of the tricycle. The selection of electric motor, solar charger and panels are dealt with. The paper highlights the advantages of dual mode of charging and economic feasibility of the tricycle. Keywords: Eco- friendly, solar charger, Brushless Motor
It shows information of new innovation technology power generation from speed breakers. for coming engineers and scientists
This file was submitted purely for presentation and knowledge sharing and gathered information from public domains mentioned in references.
@imaanbakshi
This paper discusses about design and analysis of double stator slotted rotor (DSSR) BLDC motor for electric bicycle application. Usually single stator (SS) BLDC motor is used in an electric bicycle. This type of motor has low performance and need to be charged regularly. The objective of this research is to design and analysis DSSR motor that have high torque. At starts, design specification for the electric bicycle is calculated. Next, design process for DSSR is carried out by using the desired parameter. Lastly, analysis for double stator slotted rotor is simulated using FEM. Result for average back emf, average inductance, inner stator flux density, outer stator flux density, average torque and estimate torque constant is obtained. Result for average torque from FEM archieve the requirement of motor torque for DSSR design where the maximum average torque is 16.2 Nm. This research will give benefit to mankind and society in term of environment protection and energy consumption.
Free Powered Electric Vehicle_Designed by Pranav NavathePranavNavathe
In today’s world the rapid growth in automobile industry requested most accurate and high
performable vehicles, with pollution free and low cost in operation. The project free powered electric
vehicle is an automobile which works on the principle of generating electricity with the help of
synchronous electric motor and generator with attached fly wheel, boosting circuit which acts as a
free powering machine by restoring waste mechanical energy into useful electric work. This device
consists of one electric motor and generator with attached fly wheel in centre so that it connected
with motor and generator with belt pulleys. When an mechanical input is given to the generator with
help of stator its produces electricity later which is passed to motor as input so, motor rotates the
attached flywheel then the stored kinetic energy in the flywheel is utilized to multiply the rotations of
generator shaft to produce electricity with little effort on motor in this way cycle repeated and from
produced electricity some amount of electricity taken as output which is used for charging batteries,
accessories of the electric vehicle. Such that vehicle is propelled.
Power Generation from Speed Breaker Using Crank ShaftIJARTES
Power Generation from Speed Breaker Using
Crank Shaft
This paper attempts to show how energy can
tapped and used at a commonly used system the load speed
breaker. As the demand of electric power is increasing day-byday
for the working of various appliances. Producing
electricity from various sources is needed like from a speed
breaker is a new concept that is an undergoing research. The
number of vehicles on road is increase rapidly and if we
convert some of the kinetic energy of this vehicle into
rotational motion of roller then we can produce considerable
amount of electricity. The demand of the hour is to have some
source of green energy which can be produce with less (or) no
harmful by-products. Our project is to develop an alternative
green source of energy by moving vehicles on the road ways
While moving, the vehicles possess some kinetic energy and it is being wasted. This kinetic energy can be utilized to produce power by using a special arrangement called POWER HUMP (SPEED BREAKER
In a world where environment protection and energy conversion are growing concerns,the development of solar vehicle has taken on an accele ration pace. The dream of having commercially viable solar vehicle is becoming a rea lity. EV�s are gradually available in the market. This opportunity is taken towards design an d development of Solar two wheeler. Solar vehicle is a multi-disciplinary subject which covers broad and complex aspects. However,it has core technologies,namely propulsio n technology,energy source technology,storage and control technology. As energy source s olar panel is used and developed voltage is stored in battery and used for the drive the hub motor which is used as rare wheel of the vehicle.
Design, development and performance evaluation of solar power assisted tricycleeSAT Journals
Abstract Solar energy is the only source of renewable energy which can be a feasible alternative for fossil fuels. In this work, a solar powered cycle is fabricated by modifying a all geared bicycle. The discussion covers the design, assembly and performance evaluation of the tricycle. The selection of electric motor, solar charger and panels are dealt with. The paper highlights the advantages of dual mode of charging and economic feasibility of the tricycle. Keywords: Eco- friendly, solar charger, Brushless Motor
It shows information of new innovation technology power generation from speed breakers. for coming engineers and scientists
This file was submitted purely for presentation and knowledge sharing and gathered information from public domains mentioned in references.
@imaanbakshi
This paper discusses about design and analysis of double stator slotted rotor (DSSR) BLDC motor for electric bicycle application. Usually single stator (SS) BLDC motor is used in an electric bicycle. This type of motor has low performance and need to be charged regularly. The objective of this research is to design and analysis DSSR motor that have high torque. At starts, design specification for the electric bicycle is calculated. Next, design process for DSSR is carried out by using the desired parameter. Lastly, analysis for double stator slotted rotor is simulated using FEM. Result for average back emf, average inductance, inner stator flux density, outer stator flux density, average torque and estimate torque constant is obtained. Result for average torque from FEM archieve the requirement of motor torque for DSSR design where the maximum average torque is 16.2 Nm. This research will give benefit to mankind and society in term of environment protection and energy consumption.
The International Journal of Engineering and Science (The IJES)theijes
The International Journal of Engineering & Science is aimed at providing a platform for researchers, engineers, scientists, or educators to publish their original research results, to exchange new ideas, to disseminate information in innovative designs, engineering experiences and technological skills. It is also the Journal's objective to promote engineering and technology education. All papers submitted to the Journal will be blind peer-reviewed. Only original articles will be published.
The papers for publication in The International Journal of Engineering& Science are selected through rigorous peer reviews to ensure originality, timeliness, relevance, and readability.
Generation of Electricity through Speed Breaker Mechanismtheijes
In the current scenario demand of power is increasing day by day with increasing population. On the other hand energy crisis is also a main issue of today’s life and all there is a shortage of conventional energy resources due to its large usage. So, we have to sort out this problem with a technique which will not only overcome this energy crisis but also should be eco-friendly. Many conventional resources are creating pollution so that’s why focus is towards eco-friendly solution. This project emphasizes on idea which shows that power could be generated by specially designed speed breakers. A large amount of kinetic energy is being wasted on roads on daily basis in different forms which could be use to generate power and this power can be stored in batteries. This project shows clearly how we can generate power by using rack-pinion method where basically linear motion is converted into rotary motion and then can be used to generate electricity. Large amount of electricity can be generated using this method and this method is eco-friendly.
Sachpazis:Terzaghi Bearing Capacity Estimation in simple terms with Calculati...Dr.Costas Sachpazis
Terzaghi's soil bearing capacity theory, developed by Karl Terzaghi, is a fundamental principle in geotechnical engineering used to determine the bearing capacity of shallow foundations. This theory provides a method to calculate the ultimate bearing capacity of soil, which is the maximum load per unit area that the soil can support without undergoing shear failure. The Calculation HTML Code included.
We have compiled the most important slides from each speaker's presentation. This year’s compilation, available for free, captures the key insights and contributions shared during the DfMAy 2024 conference.
6th International Conference on Machine Learning & Applications (CMLA 2024)ClaraZara1
6th International Conference on Machine Learning & Applications (CMLA 2024) will provide an excellent international forum for sharing knowledge and results in theory, methodology and applications of on Machine Learning & Applications.
Forklift Classes Overview by Intella PartsIntella Parts
Discover the different forklift classes and their specific applications. Learn how to choose the right forklift for your needs to ensure safety, efficiency, and compliance in your operations.
For more technical information, visit our website https://intellaparts.com
Immunizing Image Classifiers Against Localized Adversary Attacksgerogepatton
This paper addresses the vulnerability of deep learning models, particularly convolutional neural networks
(CNN)s, to adversarial attacks and presents a proactive training technique designed to counter them. We
introduce a novel volumization algorithm, which transforms 2D images into 3D volumetric representations.
When combined with 3D convolution and deep curriculum learning optimization (CLO), itsignificantly improves
the immunity of models against localized universal attacks by up to 40%. We evaluate our proposed approach
using contemporary CNN architectures and the modified Canadian Institute for Advanced Research (CIFAR-10
and CIFAR-100) and ImageNet Large Scale Visual Recognition Challenge (ILSVRC12) datasets, showcasing
accuracy improvements over previous techniques. The results indicate that the combination of the volumetric
input and curriculum learning holds significant promise for mitigating adversarial attacks without necessitating
adversary training.
Hierarchical Digital Twin of a Naval Power SystemKerry Sado
A hierarchical digital twin of a Naval DC power system has been developed and experimentally verified. Similar to other state-of-the-art digital twins, this technology creates a digital replica of the physical system executed in real-time or faster, which can modify hardware controls. However, its advantage stems from distributing computational efforts by utilizing a hierarchical structure composed of lower-level digital twin blocks and a higher-level system digital twin. Each digital twin block is associated with a physical subsystem of the hardware and communicates with a singular system digital twin, which creates a system-level response. By extracting information from each level of the hierarchy, power system controls of the hardware were reconfigured autonomously. This hierarchical digital twin development offers several advantages over other digital twins, particularly in the field of naval power systems. The hierarchical structure allows for greater computational efficiency and scalability while the ability to autonomously reconfigure hardware controls offers increased flexibility and responsiveness. The hierarchical decomposition and models utilized were well aligned with the physical twin, as indicated by the maximum deviations between the developed digital twin hierarchy and the hardware.