This document reviews the mechanical and tribological properties of aluminium alloys reinforced with silicon carbide (SiC) metal matrix composites. It discusses how aluminium-SiC composites have better strength, lower density, and improved wear resistance compared to other metals. The document also summarizes several studies that investigated properties like hardness, tensile strength, and wear rate of different aluminium-SiC compositions fabricated by stir casting and powder metallurgy. The studies found that reinforcement with SiC generally increased strength and hardness but decreased ductility. Properties varied with the SiC content and fabrication method.
Experimental Study of Wear Rate Coefficient of Aluminium Hybrid Composites Ma...AM Publications
In current decade, demand in material characteristics like light weight, superior strength to weight ratio, improved surface properties and enhanced wear resistance for complex engineering applications like automobile, aerospace and nuclear are researcher’s interest. However, performance of hybrid composites depends on right combination of reinforcements. Silicon carbide, silicon nitride, boron nitride and titanium carbide are few reinforcements available at present. In this work, Al356 is reinforced with SiC and B4C to enhance the mechanical properties, surface hardness and wear resistance. This hybrid composite is prepared by stir casting technique and the morphology of composite is studied using optical microscope to investigate the dispersion of reinforcements. In the present study, the wear and friction characteristics of hybrid composites are investigated using pin on disc dry wear tests by varying the load and speed and the results are tabulated for load vs mass loss, load vs wear rate and load vs wear coefficient. The results report that wear rate of hybrid composites are lower than that of binary composites. Mechanical properties, surface hardness and wear characteristics of aluminium hybrid composites are compared with that of aluminium binary composites available at present.
Aluminium Matrix Composites (AMC’s) are widely used in aerospace, automotive,
structural and marine applications due to their high strength to weight ratio, corrosion
resistance. In AMC one of constituent is aluminium or its alloy which forms a network
called as matrix phase and other constituent is embedded in matrix made of harder material
generally ceramic or non metallic material called as reinforcement. Various processing
techniques are available for manufacturing of AMC’s. Stir casting is one of the economical
and extensively used methods to enhance attractive properties of AMC’s. This paper
presents an overview of stir casing process, process parameter and preparation of AMC
using aluminium alloy as matrix phase and alumina (Al2O3) as reinforcement by varying
their proportion.
HEAT TREATMENT EFFECT ON MECHANICAL PROPERTIES AND SEM ANALYSIS OF AL6061/WC/...IAEME Publication
Recent developments in material technology help to find and fabricate new materials which may replace existing materials for various applications. Among those, composite materials play a vital role which is combination of two or more materials with different physical and chemical properties. Aluminum plays a vital role in the automotive, aerospace and marine industries this for its strength, less weight, flexibility and cost. The present study is to cast a metal matrix composite of al 6061 with the selected reinforcing materials. The reinforcing material used here are titanium (Ti), tungsten carbide (Wc), boron carbide (B4C) and chromium (Cr) in the form of particles.
Experimental Study of Wear Rate Coefficient of Aluminium Hybrid Composites Ma...AM Publications
In current decade, demand in material characteristics like light weight, superior strength to weight ratio, improved surface properties and enhanced wear resistance for complex engineering applications like automobile, aerospace and nuclear are researcher’s interest. However, performance of hybrid composites depends on right combination of reinforcements. Silicon carbide, silicon nitride, boron nitride and titanium carbide are few reinforcements available at present. In this work, Al356 is reinforced with SiC and B4C to enhance the mechanical properties, surface hardness and wear resistance. This hybrid composite is prepared by stir casting technique and the morphology of composite is studied using optical microscope to investigate the dispersion of reinforcements. In the present study, the wear and friction characteristics of hybrid composites are investigated using pin on disc dry wear tests by varying the load and speed and the results are tabulated for load vs mass loss, load vs wear rate and load vs wear coefficient. The results report that wear rate of hybrid composites are lower than that of binary composites. Mechanical properties, surface hardness and wear characteristics of aluminium hybrid composites are compared with that of aluminium binary composites available at present.
Aluminium Matrix Composites (AMC’s) are widely used in aerospace, automotive,
structural and marine applications due to their high strength to weight ratio, corrosion
resistance. In AMC one of constituent is aluminium or its alloy which forms a network
called as matrix phase and other constituent is embedded in matrix made of harder material
generally ceramic or non metallic material called as reinforcement. Various processing
techniques are available for manufacturing of AMC’s. Stir casting is one of the economical
and extensively used methods to enhance attractive properties of AMC’s. This paper
presents an overview of stir casing process, process parameter and preparation of AMC
using aluminium alloy as matrix phase and alumina (Al2O3) as reinforcement by varying
their proportion.
HEAT TREATMENT EFFECT ON MECHANICAL PROPERTIES AND SEM ANALYSIS OF AL6061/WC/...IAEME Publication
Recent developments in material technology help to find and fabricate new materials which may replace existing materials for various applications. Among those, composite materials play a vital role which is combination of two or more materials with different physical and chemical properties. Aluminum plays a vital role in the automotive, aerospace and marine industries this for its strength, less weight, flexibility and cost. The present study is to cast a metal matrix composite of al 6061 with the selected reinforcing materials. The reinforcing material used here are titanium (Ti), tungsten carbide (Wc), boron carbide (B4C) and chromium (Cr) in the form of particles.
Fabrication and evaluation of mechanical properties of al6061 IJARIIT
Metal matrix composite are widely used in automotive industries because they exhibits different mechanical properties
such as high strength and good wear resistance, high specific stiffness, low weight and high hardness etc. Due to these properties
metal matrix composite with particulate reinforcement and fabricating method has become one of the most important areas of
research. The work is mainly focus on fabrication of Al 6061 reinforced with 4% B4C (particle size 100 mesh) & 4% Cu and
method used for fabrication is stir casting method. Tensile strength, hardness, impact strength, microstructure of fabricated
composite are used to characterize it. By addition of B4C & Cu tensile strength and hardness of the fabricated composite has
increased and slightly decreased in impact strength. Scanning Electron microscopy is used to confirm the microstructure and
uniform distribution of B4C & Cu particles in metal matrix composite. The value of tensile strength increase up to 20% and
hardness increase upto15% due to addition of B4C & Cu paritcles.The physical and mechanical properties of composite are
improved so it can be used for automotive industrial applications.
A STUDY ON MECHANICAL PROPERTIES OF ALUMINUM 6063 BASED HYBRID COMPOSITESSuryamech5
1.Hybrid metal matrix composites were successfully fabricated using stir casting method.
2.Reinforcement particles such as Silicon carbide and graphite were uniformly distributed in Al matrix.
3.The hardness and tensile strength of the composite is greatly increased with increasing of graphite particles in Aluminium matrix.
4.When adding constant 5% of Sic carbide, the tensile strength is increased.
Investigation of Mechanical Behavior of Aluminium Alloys Before and After Wor...dbpublications
The ever increasing demand from aerospace industries and automotive industries to manufacture components which are lighter and stronger than conventional steel has prompted the significant usage of aluminium alloys. This research work involves the investigation of mechanical properties in aluminium alloys before and after work hardening. The alloy is work hardened using cold forging process. The major alloying elements used in the aluminium alloy are manganese, magnesium and silicon. The aluminium alloy ingots are prepared through gravity casting. After the ingots are air cooled to room temperature, they are work hardened using cold forging method where the ingots are forged at room temperature. The cold forged aluminium alloys are then subjected to tensile tests, wear tests, hardness tests and microstructure analysis using optical Scanning Electron Microscope (SEM). The material properties achieved are compared with the alloys properties that have not been subjected to work hardening. The expected outcome is to achieve a work hardened aluminium alloy that exhibits excellent mechanical properties which can be best suited for numerous industrial manufacturing requirements. Better ideal properties such as formability, weldability, increased hardness and wear resistance are expected from the cold forged alloys.
Evolution of automobile production has been driven by competitive materials. Light-weight alloys are
continuously developed as most sustainable for automotive sector. Aluminum is being used as a successful
material in automotive applications due to its low weight, higher strength, good corrosion resistance and
formability to suit different design requirements. Since aluminium has the potential to be used as replacement
of the current automotive materials like steel and cast iron, its demand has increased greatly. In a further
development aluminium metal matrix composites (MMCs) were developed and these have improved wear
resistance, high fatigue strength and better thermal stability, as compared with those of aluminum. In
automobile sector, wear is a major problem, specifically in engineering assemblies and materials used for this
purpose should have good tribological properties. To this effect Al MMCs have attracted significant attraction
since they have improved wear resistance. Metal matrix composites are usually produced with secondary
particles in the form of either continuous or discontinuous fiber or particles. From the viewpoint of good
mechanical properties aluminium matrix is generally reinforced by oxide or carbide, nitride or boride
ceramics (like Al2O3, SiC, Si3N4, TiC, TiB2. Reinforcement of the matrix with only one of these
reinforcements may not yield desired properties and the matrix may need to be augmented with other
reinforcements also. Graphite and SiC are the reinforcements used widely in automotive industries to achieve
better mechanical and tribological properties and dampen the vibrations with less operational costs.
Aluminum metal matrix composite can be produced by various methods including powder metallurgy,
conventional casting technology, etc. Among the casting methods semisolid processing of composites yields
better mechanical strength. This review deals with various manufacturing methods of metal matrix composites
processing and insight on semisolid processing and its process parameters.
Design and Fatigue Failure Analysis of hybrid fiber metal laminated Leaf SpringBharaniTharan12
A study on the fatigue strength of fiber reinforced hybrid epoxy composites was evaluated in this paper. The fiber metal laminates are hybrid composite materials are made from interlacing layers of thin metals and fiber reinforced plastics. The flexural strength of hybrid fiber metal composites was investigated from the three point bending test in accordance with ASTM D790-03 at various hybrid ratios of sequence layer in FML composites. The Glass fiber, Kevlar fiber and aluminum were taken for laminating the composite and reinforced with epoxy matrix. The adhesion property of fiber metal composites was enhanced by modified aluminium surface treatments and kevlar surface is treated with epichlorohydrin re-treatment. The interfacial fracture toughness were investigated from ASTM D5528-01. The flexural modulus and strain to failure results have been showed for various hybrid combinations, which have more effect on interlaminar strength of GARALL composites and improved fatigue life of leaf spring
Development of Aluminium Metal Matrix Composite Using Stir Casting Methodtheijes
The International Journal of Engineering & Science is aimed at providing a platform for researchers, engineers, scientists, or educators to publish their original research results, to exchange new ideas, to disseminate information in innovative designs, engineering experiences and technological skills. It is also the Journal's objective to promote engineering and technology education. All papers submitted to the Journal will be blind peer-reviewed. Only original articles will be published.
Fabrication and evaluation of mechanical properties of al6061 IJARIIT
Metal matrix composite are widely used in automotive industries because they exhibits different mechanical properties
such as high strength and good wear resistance, high specific stiffness, low weight and high hardness etc. Due to these properties
metal matrix composite with particulate reinforcement and fabricating method has become one of the most important areas of
research. The work is mainly focus on fabrication of Al 6061 reinforced with 4% B4C (particle size 100 mesh) & 4% Cu and
method used for fabrication is stir casting method. Tensile strength, hardness, impact strength, microstructure of fabricated
composite are used to characterize it. By addition of B4C & Cu tensile strength and hardness of the fabricated composite has
increased and slightly decreased in impact strength. Scanning Electron microscopy is used to confirm the microstructure and
uniform distribution of B4C & Cu particles in metal matrix composite. The value of tensile strength increase up to 20% and
hardness increase upto15% due to addition of B4C & Cu paritcles.The physical and mechanical properties of composite are
improved so it can be used for automotive industrial applications.
A STUDY ON MECHANICAL PROPERTIES OF ALUMINUM 6063 BASED HYBRID COMPOSITESSuryamech5
1.Hybrid metal matrix composites were successfully fabricated using stir casting method.
2.Reinforcement particles such as Silicon carbide and graphite were uniformly distributed in Al matrix.
3.The hardness and tensile strength of the composite is greatly increased with increasing of graphite particles in Aluminium matrix.
4.When adding constant 5% of Sic carbide, the tensile strength is increased.
Investigation of Mechanical Behavior of Aluminium Alloys Before and After Wor...dbpublications
The ever increasing demand from aerospace industries and automotive industries to manufacture components which are lighter and stronger than conventional steel has prompted the significant usage of aluminium alloys. This research work involves the investigation of mechanical properties in aluminium alloys before and after work hardening. The alloy is work hardened using cold forging process. The major alloying elements used in the aluminium alloy are manganese, magnesium and silicon. The aluminium alloy ingots are prepared through gravity casting. After the ingots are air cooled to room temperature, they are work hardened using cold forging method where the ingots are forged at room temperature. The cold forged aluminium alloys are then subjected to tensile tests, wear tests, hardness tests and microstructure analysis using optical Scanning Electron Microscope (SEM). The material properties achieved are compared with the alloys properties that have not been subjected to work hardening. The expected outcome is to achieve a work hardened aluminium alloy that exhibits excellent mechanical properties which can be best suited for numerous industrial manufacturing requirements. Better ideal properties such as formability, weldability, increased hardness and wear resistance are expected from the cold forged alloys.
Evolution of automobile production has been driven by competitive materials. Light-weight alloys are
continuously developed as most sustainable for automotive sector. Aluminum is being used as a successful
material in automotive applications due to its low weight, higher strength, good corrosion resistance and
formability to suit different design requirements. Since aluminium has the potential to be used as replacement
of the current automotive materials like steel and cast iron, its demand has increased greatly. In a further
development aluminium metal matrix composites (MMCs) were developed and these have improved wear
resistance, high fatigue strength and better thermal stability, as compared with those of aluminum. In
automobile sector, wear is a major problem, specifically in engineering assemblies and materials used for this
purpose should have good tribological properties. To this effect Al MMCs have attracted significant attraction
since they have improved wear resistance. Metal matrix composites are usually produced with secondary
particles in the form of either continuous or discontinuous fiber or particles. From the viewpoint of good
mechanical properties aluminium matrix is generally reinforced by oxide or carbide, nitride or boride
ceramics (like Al2O3, SiC, Si3N4, TiC, TiB2. Reinforcement of the matrix with only one of these
reinforcements may not yield desired properties and the matrix may need to be augmented with other
reinforcements also. Graphite and SiC are the reinforcements used widely in automotive industries to achieve
better mechanical and tribological properties and dampen the vibrations with less operational costs.
Aluminum metal matrix composite can be produced by various methods including powder metallurgy,
conventional casting technology, etc. Among the casting methods semisolid processing of composites yields
better mechanical strength. This review deals with various manufacturing methods of metal matrix composites
processing and insight on semisolid processing and its process parameters.
Design and Fatigue Failure Analysis of hybrid fiber metal laminated Leaf SpringBharaniTharan12
A study on the fatigue strength of fiber reinforced hybrid epoxy composites was evaluated in this paper. The fiber metal laminates are hybrid composite materials are made from interlacing layers of thin metals and fiber reinforced plastics. The flexural strength of hybrid fiber metal composites was investigated from the three point bending test in accordance with ASTM D790-03 at various hybrid ratios of sequence layer in FML composites. The Glass fiber, Kevlar fiber and aluminum were taken for laminating the composite and reinforced with epoxy matrix. The adhesion property of fiber metal composites was enhanced by modified aluminium surface treatments and kevlar surface is treated with epichlorohydrin re-treatment. The interfacial fracture toughness were investigated from ASTM D5528-01. The flexural modulus and strain to failure results have been showed for various hybrid combinations, which have more effect on interlaminar strength of GARALL composites and improved fatigue life of leaf spring
Development of Aluminium Metal Matrix Composite Using Stir Casting Methodtheijes
The International Journal of Engineering & Science is aimed at providing a platform for researchers, engineers, scientists, or educators to publish their original research results, to exchange new ideas, to disseminate information in innovative designs, engineering experiences and technological skills. It is also the Journal's objective to promote engineering and technology education. All papers submitted to the Journal will be blind peer-reviewed. Only original articles will be published.
WEAR STUDIES ON THE HEAT TREATED AL6061-μSIC AND AL6061-NSIC METAL MATRIX COM...IAEME Publication
Metal matrix composites (MMCs) have a potential for enhanced wear conflict in
excess of the unreinforced aluminum alloy and are the most capable in achieving
enhanced mechanical properties. In the present investigation, composites of Aluminum
6061(Al6061) matrix material is reinforced with micron size Silicon carbide (μSiC)
reinforcement with 5, 10 and 15 weight percentages (wt.%) and nano size SiC (nSiC)
with 0.5, 1.0 and 1.5 wt.% are fabricated by stir casting technique. The stir casted
composites are further heat treated and the specimens are prepared as per ASTM
standards to conduct hardness and wear tests. The fabricated and heat treated nano
composites showed enhancement in hardness and wear resistance more than the micro
composites. The microstructure of the worn out specimen are examined by scanning
electron microscope. Taking into contemplation all the factors, it can be concluded that
aluminum based composite with 1.0% by weight nano SiC reinforcement acquire
superior wear resistance properties as compared to micro SiC reinforced aluminum
metal matrix composites.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
Microstructure and Hardness of Aluminium Alloy- Fused Silica Particulate Comp...AM Publications
Aluminum matrix composites (AMCs) refer to the class of light weight high performance aluminum centric
material systems. The reinforcement in AMCs could be in the form of continuous/discontinuous fibers, whiskers or particulates,
in volume fractions. Properties of AMCs can be tailored to the demands of different industrial applications by suitable
combinations of matrix, reinforcement and processing route. This work focuses on the fabrication of aluminum alloy (LM13)
matrix composites reinforced with 9%, 12% &15% fused silica particulates using stir casting route. The microstructure and
hardness of the fabricated composite were analyzed and reported.
ER Publication,
IJETR, IJMCTR,
Journals,
International Journals,
High Impact Journals,
Monthly Journal,
Good quality Journals,
Research,
Research Papers,
Research Article,
Free Journals, Open access Journals,
erpublication.org,
Engineering Journal,
Science Journals,
REVIEW ON MECHANICAL PROPERTIES OF NON-ASBESTOS COMPOSITE MATERIAL USED IN BR...ijiert bestjournal
Metallic matrix composites are combinations of two or more different metals inter metallic compounds or second phases in which dispersed phases are embe dded within the metallic matrix. They are produced by controlling the morphologies of the constituents to achieve optimum combination of properties. Properties of the composites depend on the properti es of the constituent phases,their relative amount,and dispersed phase geometry including particle siz e,shape and orientation in the matrix. In this pap er,The mechanical properties,behaviour and micro stru ctural evolution of aluminium metal matrix metallic composites fabricated under various process conditi ons were investigated to understand their process- structure�property relations by optimization proces s. Addition of silicon carbide to aluminum has show n an increase in its mechanical properties.
Synthesis And Characterization of Aluminum –Silicon-Fly Ash Composite By Stir...IRJESJOURNAL
Abstract :- In this work aluminium 7075 as matrix and silicon carbide and fly ash as reinforcements has been used. The %wt of reinforcement are varied to study the difference in aluminium property. Following are the samples are aluminium 7075 as 100%, aluminium 7075 90% + 10% SiC, and aluminium 7075 90% + 10% fly ash. The materials are obtained by stir casting technique. During casting 300 grams of aluminium has been taken as sample 1. 270grams of aluminium has been taken with 30grams of SiC as sample 2. The third sample is the mixture of 270grams of aluminium with 30grams of fly ash. Then the materials are made in the form of cylindrical rod of 30mm diameter and max length of 70mm. The composites are analysed for the mechanical study and the results are obtained based on hardness and the work has been extended to study the micro structure of the specimen by SEM analysis and Chemical Conformation.
Similar to IRJET - An Investigation of the Mechanical and Tribological Properties of Aluminium Alloy Series with SIC Metal Matrix Composites: A Review (20)
Automobile Management System Project Report.pdfKamal Acharya
The proposed project is developed to manage the automobile in the automobile dealer company. The main module in this project is login, automobile management, customer management, sales, complaints and reports. The first module is the login. The automobile showroom owner should login to the project for usage. The username and password are verified and if it is correct, next form opens. If the username and password are not correct, it shows the error message.
When a customer search for a automobile, if the automobile is available, they will be taken to a page that shows the details of the automobile including automobile name, automobile ID, quantity, price etc. “Automobile Management System” is useful for maintaining automobiles, customers effectively and hence helps for establishing good relation between customer and automobile organization. It contains various customized modules for effectively maintaining automobiles and stock information accurately and safely.
When the automobile is sold to the customer, stock will be reduced automatically. When a new purchase is made, stock will be increased automatically. While selecting automobiles for sale, the proposed software will automatically check for total number of available stock of that particular item, if the total stock of that particular item is less than 5, software will notify the user to purchase the particular item.
Also when the user tries to sale items which are not in stock, the system will prompt the user that the stock is not enough. Customers of this system can search for a automobile; can purchase a automobile easily by selecting fast. On the other hand the stock of automobiles can be maintained perfectly by the automobile shop manager overcoming the drawbacks of existing system.
Cosmetic shop management system project report.pdfKamal Acharya
Buying new cosmetic products is difficult. It can even be scary for those who have sensitive skin and are prone to skin trouble. The information needed to alleviate this problem is on the back of each product, but it's thought to interpret those ingredient lists unless you have a background in chemistry.
Instead of buying and hoping for the best, we can use data science to help us predict which products may be good fits for us. It includes various function programs to do the above mentioned tasks.
Data file handling has been effectively used in the program.
The automated cosmetic shop management system should deal with the automation of general workflow and administration process of the shop. The main processes of the system focus on customer's request where the system is able to search the most appropriate products and deliver it to the customers. It should help the employees to quickly identify the list of cosmetic product that have reached the minimum quantity and also keep a track of expired date for each cosmetic product. It should help the employees to find the rack number in which the product is placed.It is also Faster and more efficient way.
Courier management system project report.pdfKamal Acharya
It is now-a-days very important for the people to send or receive articles like imported furniture, electronic items, gifts, business goods and the like. People depend vastly on different transport systems which mostly use the manual way of receiving and delivering the articles. There is no way to track the articles till they are received and there is no way to let the customer know what happened in transit, once he booked some articles. In such a situation, we need a system which completely computerizes the cargo activities including time to time tracking of the articles sent. This need is fulfilled by Courier Management System software which is online software for the cargo management people that enables them to receive the goods from a source and send them to a required destination and track their status from time to time.
About
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.
Technical Specifications
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
Key Features
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface
• Compatible with MAFI CCR system
• Copatiable with IDM8000 CCR
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
Application
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.
Final project report on grocery store management system..pdfKamal Acharya
In today’s fast-changing business environment, it’s extremely important to be able to respond to client needs in the most effective and timely manner. If your customers wish to see your business online and have instant access to your products or services.
Online Grocery Store is an e-commerce website, which retails various grocery products. This project allows viewing various products available enables registered users to purchase desired products instantly using Paytm, UPI payment processor (Instant Pay) and also can place order by using Cash on Delivery (Pay Later) option. This project provides an easy access to Administrators and Managers to view orders placed using Pay Later and Instant Pay options.
In order to develop an e-commerce website, a number of Technologies must be studied and understood. These include multi-tiered architecture, server and client-side scripting techniques, implementation technologies, programming language (such as PHP, HTML, CSS, JavaScript) and MySQL relational databases. This is a project with the objective to develop a basic website where a consumer is provided with a shopping cart website and also to know about the technologies used to develop such a website.
This document will discuss each of the underlying technologies to create and implement an e- commerce website.
Welcome to WIPAC Monthly the magazine brought to you by the LinkedIn Group Water Industry Process Automation & Control.
In this month's edition, along with this month's industry news to celebrate the 13 years since the group was created we have articles including
A case study of the used of Advanced Process Control at the Wastewater Treatment works at Lleida in Spain
A look back on an article on smart wastewater networks in order to see how the industry has measured up in the interim around the adoption of Digital Transformation in the Water Industry.
Sachpazis:Terzaghi Bearing Capacity Estimation in simple terms with Calculati...Dr.Costas Sachpazis
Terzaghi's soil bearing capacity theory, developed by Karl Terzaghi, is a fundamental principle in geotechnical engineering used to determine the bearing capacity of shallow foundations. This theory provides a method to calculate the ultimate bearing capacity of soil, which is the maximum load per unit area that the soil can support without undergoing shear failure. The Calculation HTML Code included.
CFD Simulation of By-pass Flow in a HRSG module by R&R Consult.pptxR&R Consult
CFD analysis is incredibly effective at solving mysteries and improving the performance of complex systems!
Here's a great example: At a large natural gas-fired power plant, where they use waste heat to generate steam and energy, they were puzzled that their boiler wasn't producing as much steam as expected.
R&R and Tetra Engineering Group Inc. were asked to solve the issue with reduced steam production.
An inspection had shown that a significant amount of hot flue gas was bypassing the boiler tubes, where the heat was supposed to be transferred.
R&R Consult conducted a CFD analysis, which revealed that 6.3% of the flue gas was bypassing the boiler tubes without transferring heat. The analysis also showed that the flue gas was instead being directed along the sides of the boiler and between the modules that were supposed to capture the heat. This was the cause of the reduced performance.
Based on our results, Tetra Engineering installed covering plates to reduce the bypass flow. This improved the boiler's performance and increased electricity production.
It is always satisfying when we can help solve complex challenges like this. Do your systems also need a check-up or optimization? Give us a call!
Work done in cooperation with James Malloy and David Moelling from Tetra Engineering.
More examples of our work https://www.r-r-consult.dk/en/cases-en/
Saudi Arabia stands as a titan in the global energy landscape, renowned for its abundant oil and gas resources. It's the largest exporter of petroleum and holds some of the world's most significant reserves. Let's delve into the top 10 oil and gas projects shaping Saudi Arabia's energy future in 2024.
Quality defects in TMT Bars, Possible causes and Potential Solutions.PrashantGoswami42
Maintaining high-quality standards in the production of TMT bars is crucial for ensuring structural integrity in construction. Addressing common defects through careful monitoring, standardized processes, and advanced technology can significantly improve the quality of TMT bars. Continuous training and adherence to quality control measures will also play a pivotal role in minimizing these defects.