The document provides an introduction to effluent treatment for tanneries. It discusses the objectives of primary treatment, which includes screening, pumping, fine screening, equalization, chemical treatment, and settling. Biological (secondary) treatment is then covered, including the basic principles and operational parameters of aeration devices, oxidation ditches, and secondary sedimentation. Advanced (tertiary) treatment and sludge handling are also briefly discussed. The document aims to help tanners and managers understand the basic principles and methods of tannery effluent treatment.
Introduction to treatment_of_tannery_effluentssafwan patel
This document provides an introduction to effluent treatment for tanneries. It discusses the objectives and basic principles of primary, biological, and advanced treatment. Primary treatment involves screening, pumping, chemical coagulation/flocculation, and sedimentation to remove solids. Biological treatment uses aerobic bacteria to break down organic matter through aeration in sedimentation basins. Advanced tertiary treatment can further polish the effluent quality before discharge or reuse. The document emphasizes pollution prevention through cleaner production methods and stresses the importance of proper sludge handling and treatment plant management for environmental protection.
The document discusses effluent treatment plants (ETPs), which are necessary for treating wastewater from industries like textile processing that generate large amounts of pollution. It provides an overview of the various processes involved in ETPs, including primary treatment to remove solids, secondary treatment using biological processes, and tertiary treatment to further clean the water before discharge or reuse. The document outlines the key stages and treatments at both small and large scale ETPs, and addresses some common questions about effluent treatment.
Report on Effluent Treatment Plant (ETP) Operation and Maintenance of Interst...Kowshick Sen
Interstoff Apparels Ltd (IAL) comprises of the latest, most technologically advanced 100% export oriented private limited company with composite knitting, dyeing, finishing and apparel manufacturing plants situated in Chandra, Kaliyakoir, Gazipur, Bangladesh. IAL installed an Effluent Treatment Plant of 75 m3/Hr capacity which is running 24 Hr in a day. By nature, our ETP is Bio-logical with Chemical namely Bio-Chemical plant. This treatment is done by four stages such as preliminary, primary, secondary and tertiary treatment. Waste water comes from mainly dyeing and washing through a trench to equalization tank so for preliminary treatment is done by screening by using net or sieve for removal of large solids such as rags, sticks, grit and grease that may result in damage to equipment or operational problems at different stages of trench.
The document discusses a 10 KLD sewage treatment plant being built at a government college in Maharashtra. It summarizes the multi-stage sewage treatment process, including preliminary treatment to remove solids, primary treatment using sedimentation and skimming, secondary treatment using biological processes, and tertiary treatment to remove remaining contaminants. It provides details on the treatment plant components and standards for treated wastewater quality before discharge or reuse.
It is important & most useful presentation about ETP.
Created By: 131 TE-2 batch student
BGMEA University of Fashion & Technology (BUFT)
Textile Engineering Department
Course: Bangladesh Studies
This document provides an overview of a turnkey solution for water and wastewater treatment. It discusses various treatment processes including bioaugmentation, screens, primary clarification, biological processes, and sedimentation tanks. It then focuses on the activated sludge process for secondary treatment, describing the basic process, design considerations like organic loading and aeration requirements, and different aeration methods like diffused, spray, turbine, and surface aeration.
This document describes a common effluent treatment plant (CETP) designed to treat wastewater from tanneries. It first provides background on tanneries and the wastewater generation process. It then outlines the key components of the CETP, including primary treatment using screens and settling tanks, secondary treatment using aeration and clarification, and tertiary treatment using filters. It also discusses chemical dosing requirements and design parameters like retention time. The CETP is presented as an effective way to treat combined wastewater from multiple tanneries to reduce costs and help meet discharge standards.
Introduction to treatment_of_tannery_effluentssafwan patel
This document provides an introduction to effluent treatment for tanneries. It discusses the objectives and basic principles of primary, biological, and advanced treatment. Primary treatment involves screening, pumping, chemical coagulation/flocculation, and sedimentation to remove solids. Biological treatment uses aerobic bacteria to break down organic matter through aeration in sedimentation basins. Advanced tertiary treatment can further polish the effluent quality before discharge or reuse. The document emphasizes pollution prevention through cleaner production methods and stresses the importance of proper sludge handling and treatment plant management for environmental protection.
The document discusses effluent treatment plants (ETPs), which are necessary for treating wastewater from industries like textile processing that generate large amounts of pollution. It provides an overview of the various processes involved in ETPs, including primary treatment to remove solids, secondary treatment using biological processes, and tertiary treatment to further clean the water before discharge or reuse. The document outlines the key stages and treatments at both small and large scale ETPs, and addresses some common questions about effluent treatment.
Report on Effluent Treatment Plant (ETP) Operation and Maintenance of Interst...Kowshick Sen
Interstoff Apparels Ltd (IAL) comprises of the latest, most technologically advanced 100% export oriented private limited company with composite knitting, dyeing, finishing and apparel manufacturing plants situated in Chandra, Kaliyakoir, Gazipur, Bangladesh. IAL installed an Effluent Treatment Plant of 75 m3/Hr capacity which is running 24 Hr in a day. By nature, our ETP is Bio-logical with Chemical namely Bio-Chemical plant. This treatment is done by four stages such as preliminary, primary, secondary and tertiary treatment. Waste water comes from mainly dyeing and washing through a trench to equalization tank so for preliminary treatment is done by screening by using net or sieve for removal of large solids such as rags, sticks, grit and grease that may result in damage to equipment or operational problems at different stages of trench.
The document discusses a 10 KLD sewage treatment plant being built at a government college in Maharashtra. It summarizes the multi-stage sewage treatment process, including preliminary treatment to remove solids, primary treatment using sedimentation and skimming, secondary treatment using biological processes, and tertiary treatment to remove remaining contaminants. It provides details on the treatment plant components and standards for treated wastewater quality before discharge or reuse.
It is important & most useful presentation about ETP.
Created By: 131 TE-2 batch student
BGMEA University of Fashion & Technology (BUFT)
Textile Engineering Department
Course: Bangladesh Studies
This document provides an overview of a turnkey solution for water and wastewater treatment. It discusses various treatment processes including bioaugmentation, screens, primary clarification, biological processes, and sedimentation tanks. It then focuses on the activated sludge process for secondary treatment, describing the basic process, design considerations like organic loading and aeration requirements, and different aeration methods like diffused, spray, turbine, and surface aeration.
This document describes a common effluent treatment plant (CETP) designed to treat wastewater from tanneries. It first provides background on tanneries and the wastewater generation process. It then outlines the key components of the CETP, including primary treatment using screens and settling tanks, secondary treatment using aeration and clarification, and tertiary treatment using filters. It also discusses chemical dosing requirements and design parameters like retention time. The CETP is presented as an effective way to treat combined wastewater from multiple tanneries to reduce costs and help meet discharge standards.
The document discusses the treatment of industrial wastewater in an effluent treatment plant (ETP). It describes the various treatment units used in an ETP including preliminary (screens, grit chambers), primary (sedimentation tanks), secondary (activated sludge process, trickling filters), and tertiary (filtration, activated carbon) treatments. The goal of an ETP is to remove pollutants from wastewater through physical, chemical, and biological processes before discharge or reuse, in order to prevent environmental pollution and protect public health. Major pollutants removed include suspended solids, oil and grease, and organic materials that consume oxygen.
The document summarizes the characterization of textile effluent in Bangladesh. It finds that textile wastewater contains high levels of pollutants like BOD, COD, TSS, TDS, and heavy metals. While standards for effluent quality exist, many textile mills do not properly treat wastewater before discharging it. Without adequate treatment, textile effluent pollutes waterways and poses environmental and health risks. The study finds areas around Dhaka and Narayangong have particularly high pH and TDS levels in textile wastewater. Improved enforcement of wastewater treatment regulations is needed to address pollution from the textile industry in Bangladesh.
Treatment of Effluents from Petroleum RefineriesAsheesh Padiyar
A brief power point presentation on the Effluent treatment from Petroleum Refineries for a Chemical Engineer.Chemical Engineers are also involved in the water treatment , and is of huge concern with the amount of water needed / contaminated during the refinery mass transfer operations.
The document provides information about effluent treatment plants (ETPs). It discusses the need to treat effluent to prevent environmental pollution. It describes the major treatment units in ETPs, which include preliminary treatment to remove solids, primary treatment using sedimentation to remove heavier particles, and secondary treatment using biological processes like activated sludge or trickling filters to break down organic matter. The document contains detailed information about the individual processes and units used at each stage of treatment in an ETP.
This document provides information about the wastewater treatment process at Renata Limited, a pharmaceutical manufacturer in Bangladesh. Renata has water treatment plants and effluent treatment plants at each of its five manufacturing facilities. The effluent treatment plant uses a physico-chemical treatment process including equalization, coagulation, flocculation, sedimentation, sand filtration, activated carbon filtration, and aeration to treat wastewater and reduce pollutants before discharging to the municipal sewer system. Plant staff monitor influent and effluent water quality parameters regularly to evaluate the treatment system's performance.
Technologies of sulphur dioxide reduction in coal fired thermal power planIAEME Publication
This document summarizes research from the Proceedings of the 2nd International Conference on Current Trends in Engineering and Management. It discusses various methods for reducing sulphur dioxide emissions from coal-fired power plants, including coal blending, boiler modernization, flue gas desulphurization (FGD) technology, and switching to natural gas. The research focuses on evaluating SO2 reduction through FGD systems. Key findings include: (1) Maximum SO2 reduction occurs with high limestone purity and increasing flue gas flow rates through the absorber; (2) Blending high and low sulfur coals can reduce overall sulfur content and SO2 emissions; (3) Increasing the blade pitch of booster fans to control
The document summarizes the operations of a Common Effluent Treatment Plant (CETP) in Baddi, India. The CETP treats 25 million liters of industrial wastewater per day that is collected from over 300 industries through a 62km pipeline network. It categorizes the wastewater into 5 categories based on contamination levels and treats it using various tanks, instruments, and processes like bioaugmentation and chemical preparation. Key operations include equalization, sedimentation, aeration, and tertiary treatment. The CETP aims to reduce environmental pollution through centralized treatment of industrial effluent.
Lecture note of Industrial Waste Treatment (Elective -III) as per syllabus of Solapur university for BE Civil
Prepared by
Prof S S Jahagirdar,
Associate Professor,
N K ORchid College of Engg and Tech,
Solapur
This document describes a domestic wastewater treatment system that uses natural processes to treat greywater and blackwater over 60-72 hours. It uses an inspection chamber, baffle filter, planted gravel filter, and storage tank to treat wastewater from a 4 person household generating around 480 liters per day. The treated greywater from the system was used to successfully cultivate rice on a rooftop, yielding 30kg of rice 3 times per year.
This document summarizes the key steps and processes involved in sewage treatment. It first defines sewage as household liquid waste from sources like toilets and sinks that is collected in sewers, sometimes also including industrial waste. The treatment process involves preliminary, primary, and secondary stages to remove solids and organic matter through physical, chemical, and biological processes like sedimentation and activated sludge. Tertiary treatment provides a final polishing step to further improve water quality before discharge through additional filtration or nutrient removal.
Distillery Industry Waste and Its TreatmentLakhan Kumar
This document summarizes the waste generated by distillery industries and methods for treating distillery wastewater. Distilleries producing alcohol from molasses generate 60-100 liters of wastewater per liter of alcohol in the form of spent wash, spent lees, and yeast sludge. The spent wash is hot, acidic, and high in organic matter. Biological treatment methods like anaerobic digestion followed by aerobic processes like activated sludge or trickling filters are commonly used to treat the wastewater before disposal in water courses or on land. The treated effluent must meet standards for biochemical oxygen demand and total dissolved solids before disposal.
With rising crude prices and depleting quality of crude, however, the level of wastewater pollutants in petroleum wastewater is at new high. Such conditions are forcing refineries to use a more advanced water treatment, water recovery methods, and robust processes that work well under a variety of conditions and can handle the changing refinery effluent flow rates. Finally a process that is economical in overall life time cost is needed to make all of this feasible. Aquatech has experience working with these refinery effluent pollutants in the refinery market and offers the advanced petroleum wastewater treatment and recovery technology necessary for the refinery’s needs.
The document provides an introduction to industrial wastewater treatment. It discusses how industries use water for manufacturing and processing, which becomes wastewater after use. The wastewater must be treated before discharge to prevent environmental pollution and protect domestic sewage systems. Common contaminants in wastewater are discussed, along with characteristics of industrial wastewater. Finally, the main treatment technologies are described at a high level, including mechanical, physical, chemical, biological, and advanced processes.
This document summarizes the key processes involved in wastewater treatment, including primary, secondary, and tertiary treatment stages. Primary treatment involves physical processes like screening and sedimentation to remove solids. Secondary treatment uses biological processes like trickling filters, activated sludge tanks, and anaerobic digesters to break down organic matter. Tertiary treatment provides disinfection using chlorination, UV light, or ozonation to remove pathogens before wastewater is discharged.
Adequacy and Efficacy of Treatment Plant Treating Electronics Industry Wastewater with the parameters : BOD, COD, TSS, TDS, Heavy Metals, Nitrogen and Phosphate.
Waste water in USJP and water treatment MethodsTrishan Perera
Waste water in USJP and water treatment Methods
A presentation Done by the 1st Year Students (Group 5) of the Department of Forestry and Environmental Sciences, University of Sri Jayewardenepura for the Environmental Chemistry Assignment..
This document discusses economical wastewater treatment solutions for remote and unsewered areas. It proposes the development of self-sustainable wastewater treatment systems that comply with environmental regulations but are also energy efficient and low cost. It then describes the "AWWT" approach of anaerobic wastewater treatment and watershed management techniques like water recycling, zero discharge industries, and prevention of overdrafting groundwater. The document provides examples of AWWT projects and their methodology involving separation of rainwater, anaerobic digestion, and disposal of treated water for irrigation. It highlights the benefits of anaerobic pre-treatment in reducing sludge and energy requirements while producing biogas.
Introduction to treatment_of_tannery_effluentssafwan patel
The document provides an introduction to effluent treatment for tanneries. It discusses the objectives of primary treatment including screening, pumping, fine screening, equalization, and chemical treatment. It then covers biological secondary treatment using aerobic and anaerobic methods. Tertiary treatment and sludge handling are also addressed. The document aims to help tanners understand effluent treatment principles and requirements.
This document outlines depreciation rates for various assets as per the Indian Income Tax Act. It includes the following:
1. Depreciation rates are provided for various tangible assets like buildings, plants and machinery, computers, vehicles and medical equipment. Rates range from 15% to 100%.
2. Higher depreciation rates of 60-100% are given for pollution control equipment, specified machinery in textiles and other sectors, and energy efficient devices.
3. Intangible assets like know-how, copyrights and trademarks are also covered, with depreciation rate of 25%.
4. Detailed notes explain terms like commercial vehicle, computers, and applicability of rates for renovation
BeeOffice - the best office automation tool for your company!Jakub Żurek
BeeOffice is the best cloud based office automation system for your company! Typical office processes in one place: drom resource reservations and time planning till business trip settlement an dholiday planing! Check it out: www.beeoffice.com/enterprise
The document discusses the treatment of industrial wastewater in an effluent treatment plant (ETP). It describes the various treatment units used in an ETP including preliminary (screens, grit chambers), primary (sedimentation tanks), secondary (activated sludge process, trickling filters), and tertiary (filtration, activated carbon) treatments. The goal of an ETP is to remove pollutants from wastewater through physical, chemical, and biological processes before discharge or reuse, in order to prevent environmental pollution and protect public health. Major pollutants removed include suspended solids, oil and grease, and organic materials that consume oxygen.
The document summarizes the characterization of textile effluent in Bangladesh. It finds that textile wastewater contains high levels of pollutants like BOD, COD, TSS, TDS, and heavy metals. While standards for effluent quality exist, many textile mills do not properly treat wastewater before discharging it. Without adequate treatment, textile effluent pollutes waterways and poses environmental and health risks. The study finds areas around Dhaka and Narayangong have particularly high pH and TDS levels in textile wastewater. Improved enforcement of wastewater treatment regulations is needed to address pollution from the textile industry in Bangladesh.
Treatment of Effluents from Petroleum RefineriesAsheesh Padiyar
A brief power point presentation on the Effluent treatment from Petroleum Refineries for a Chemical Engineer.Chemical Engineers are also involved in the water treatment , and is of huge concern with the amount of water needed / contaminated during the refinery mass transfer operations.
The document provides information about effluent treatment plants (ETPs). It discusses the need to treat effluent to prevent environmental pollution. It describes the major treatment units in ETPs, which include preliminary treatment to remove solids, primary treatment using sedimentation to remove heavier particles, and secondary treatment using biological processes like activated sludge or trickling filters to break down organic matter. The document contains detailed information about the individual processes and units used at each stage of treatment in an ETP.
This document provides information about the wastewater treatment process at Renata Limited, a pharmaceutical manufacturer in Bangladesh. Renata has water treatment plants and effluent treatment plants at each of its five manufacturing facilities. The effluent treatment plant uses a physico-chemical treatment process including equalization, coagulation, flocculation, sedimentation, sand filtration, activated carbon filtration, and aeration to treat wastewater and reduce pollutants before discharging to the municipal sewer system. Plant staff monitor influent and effluent water quality parameters regularly to evaluate the treatment system's performance.
Technologies of sulphur dioxide reduction in coal fired thermal power planIAEME Publication
This document summarizes research from the Proceedings of the 2nd International Conference on Current Trends in Engineering and Management. It discusses various methods for reducing sulphur dioxide emissions from coal-fired power plants, including coal blending, boiler modernization, flue gas desulphurization (FGD) technology, and switching to natural gas. The research focuses on evaluating SO2 reduction through FGD systems. Key findings include: (1) Maximum SO2 reduction occurs with high limestone purity and increasing flue gas flow rates through the absorber; (2) Blending high and low sulfur coals can reduce overall sulfur content and SO2 emissions; (3) Increasing the blade pitch of booster fans to control
The document summarizes the operations of a Common Effluent Treatment Plant (CETP) in Baddi, India. The CETP treats 25 million liters of industrial wastewater per day that is collected from over 300 industries through a 62km pipeline network. It categorizes the wastewater into 5 categories based on contamination levels and treats it using various tanks, instruments, and processes like bioaugmentation and chemical preparation. Key operations include equalization, sedimentation, aeration, and tertiary treatment. The CETP aims to reduce environmental pollution through centralized treatment of industrial effluent.
Lecture note of Industrial Waste Treatment (Elective -III) as per syllabus of Solapur university for BE Civil
Prepared by
Prof S S Jahagirdar,
Associate Professor,
N K ORchid College of Engg and Tech,
Solapur
This document describes a domestic wastewater treatment system that uses natural processes to treat greywater and blackwater over 60-72 hours. It uses an inspection chamber, baffle filter, planted gravel filter, and storage tank to treat wastewater from a 4 person household generating around 480 liters per day. The treated greywater from the system was used to successfully cultivate rice on a rooftop, yielding 30kg of rice 3 times per year.
This document summarizes the key steps and processes involved in sewage treatment. It first defines sewage as household liquid waste from sources like toilets and sinks that is collected in sewers, sometimes also including industrial waste. The treatment process involves preliminary, primary, and secondary stages to remove solids and organic matter through physical, chemical, and biological processes like sedimentation and activated sludge. Tertiary treatment provides a final polishing step to further improve water quality before discharge through additional filtration or nutrient removal.
Distillery Industry Waste and Its TreatmentLakhan Kumar
This document summarizes the waste generated by distillery industries and methods for treating distillery wastewater. Distilleries producing alcohol from molasses generate 60-100 liters of wastewater per liter of alcohol in the form of spent wash, spent lees, and yeast sludge. The spent wash is hot, acidic, and high in organic matter. Biological treatment methods like anaerobic digestion followed by aerobic processes like activated sludge or trickling filters are commonly used to treat the wastewater before disposal in water courses or on land. The treated effluent must meet standards for biochemical oxygen demand and total dissolved solids before disposal.
With rising crude prices and depleting quality of crude, however, the level of wastewater pollutants in petroleum wastewater is at new high. Such conditions are forcing refineries to use a more advanced water treatment, water recovery methods, and robust processes that work well under a variety of conditions and can handle the changing refinery effluent flow rates. Finally a process that is economical in overall life time cost is needed to make all of this feasible. Aquatech has experience working with these refinery effluent pollutants in the refinery market and offers the advanced petroleum wastewater treatment and recovery technology necessary for the refinery’s needs.
The document provides an introduction to industrial wastewater treatment. It discusses how industries use water for manufacturing and processing, which becomes wastewater after use. The wastewater must be treated before discharge to prevent environmental pollution and protect domestic sewage systems. Common contaminants in wastewater are discussed, along with characteristics of industrial wastewater. Finally, the main treatment technologies are described at a high level, including mechanical, physical, chemical, biological, and advanced processes.
This document summarizes the key processes involved in wastewater treatment, including primary, secondary, and tertiary treatment stages. Primary treatment involves physical processes like screening and sedimentation to remove solids. Secondary treatment uses biological processes like trickling filters, activated sludge tanks, and anaerobic digesters to break down organic matter. Tertiary treatment provides disinfection using chlorination, UV light, or ozonation to remove pathogens before wastewater is discharged.
Adequacy and Efficacy of Treatment Plant Treating Electronics Industry Wastewater with the parameters : BOD, COD, TSS, TDS, Heavy Metals, Nitrogen and Phosphate.
Waste water in USJP and water treatment MethodsTrishan Perera
Waste water in USJP and water treatment Methods
A presentation Done by the 1st Year Students (Group 5) of the Department of Forestry and Environmental Sciences, University of Sri Jayewardenepura for the Environmental Chemistry Assignment..
This document discusses economical wastewater treatment solutions for remote and unsewered areas. It proposes the development of self-sustainable wastewater treatment systems that comply with environmental regulations but are also energy efficient and low cost. It then describes the "AWWT" approach of anaerobic wastewater treatment and watershed management techniques like water recycling, zero discharge industries, and prevention of overdrafting groundwater. The document provides examples of AWWT projects and their methodology involving separation of rainwater, anaerobic digestion, and disposal of treated water for irrigation. It highlights the benefits of anaerobic pre-treatment in reducing sludge and energy requirements while producing biogas.
Introduction to treatment_of_tannery_effluentssafwan patel
The document provides an introduction to effluent treatment for tanneries. It discusses the objectives of primary treatment including screening, pumping, fine screening, equalization, and chemical treatment. It then covers biological secondary treatment using aerobic and anaerobic methods. Tertiary treatment and sludge handling are also addressed. The document aims to help tanners understand effluent treatment principles and requirements.
This document outlines depreciation rates for various assets as per the Indian Income Tax Act. It includes the following:
1. Depreciation rates are provided for various tangible assets like buildings, plants and machinery, computers, vehicles and medical equipment. Rates range from 15% to 100%.
2. Higher depreciation rates of 60-100% are given for pollution control equipment, specified machinery in textiles and other sectors, and energy efficient devices.
3. Intangible assets like know-how, copyrights and trademarks are also covered, with depreciation rate of 25%.
4. Detailed notes explain terms like commercial vehicle, computers, and applicability of rates for renovation
BeeOffice - the best office automation tool for your company!Jakub Żurek
BeeOffice is the best cloud based office automation system for your company! Typical office processes in one place: drom resource reservations and time planning till business trip settlement an dholiday planing! Check it out: www.beeoffice.com/enterprise
This document provides an overview of reverse osmosis technology. It discusses how reverse osmosis was first used commercially in 1970 by Texas Instruments to treat water for electronics manufacturing. It then summarizes growth in global reverse osmosis capacity from 880,000 gallons per day in 1970 to over 500 million gallons per day in 1984. The document also reviews key applications of reverse osmosis including industrial, municipal, power, and military uses.
The Prayer of St. Francis asks God to make the speaker a channel of peace who brings love where there is hatred, pardon where there is injury, and faith where there is doubt. It also asks to understand rather than be understood, to love rather than be loved, and to console rather than be consoled, so that in pardoning others the speaker is pardoned, in giving to others they receive, and in dying they are born to eternal life.
The document summarizes the multi-step process used to treat sewage at the Mangere treatment plant in New Zealand. Sewage undergoes pretreatment to remove large solids, primary treatment to separate out grit, suspended solids, and scum, and secondary treatment where the solid and liquid components are further processed. Solids are digested and decomposed, while liquids undergo additional treatment including biological breakdown before final release into the harbor. Testing at various stages ensures the effluent meets purity standards.
This document discusses the history and applications of reverse osmosis technology. It notes that:
- The first large industrial reverse osmosis system was installed in 1970 at a Texas Instruments plant, where it increased manufacturing yields enough to pay for itself in two weeks.
- By the end of 1984, global reverse osmosis operating capacity was 524 million gallons per day, with the largest uses being municipal water supplies (38%), industrial process water (31.5%), and power plant water (11%).
- Reverse osmosis transforms unusable water into a usable resource by applying pressure greater than the osmotic pressure to force water molecules through a semi-permeable membrane, leaving dissolved ions behind.
This document provides an overview of sewage/wastewater treatment and the history and evolution of treatment methods. It defines sewage/wastewater and explains why treatment is necessary before disposal due to environmental and public health impacts. It then discusses the historical development of sewage treatment from the late 1800s onwards in response to health concerns. The document outlines various unit operations and processes used in treatment including physical, chemical and biological methods. It categorizes treatment levels from preliminary to primary, secondary and tertiary/advanced. Finally, it discusses factors that influence the selection and design of treatment systems such as engineering, environmental, process and cost considerations.
The document provides an overview of organic substances that occur in effluents from domestic wastewater treatment plants. It discusses the wastewater treatment process and the principles of removing organic components. Many different micro pollutants can be found in effluent, and while removal efficiencies are often high, they are not always sufficient for complete removal. The document evaluates the occurrence and removal efficiency of several classes of contaminants, such as pharmaceuticals, personal care products, and industrial chemicals. It concludes that the quality of surface waters is not sufficient to allow simple drinking water treatment.
This document discusses options for upgrading the wastewater treatment system in a small Swedish village called Vadsbro. It outlines a planning process for evaluating alternatives that considers requirements around disease prevention, environmental protection of local water bodies, and nutrient recycling. Five treatment options are described that could meet these requirements, including use of energy forests, stabilization ponds, biofilter ditches, crop-wetland rotation, sand filters, or a package treatment plant. The local situation in Vadsbro and economics are also discussed. A decision will be made by the municipality on the best system to implement.
The document discusses the pH scale and how it is used to indicate the acidity or basicity of aqueous solutions. It defines pH as the negative logarithm of the hydronium ion concentration and explains that solutions have an acidic pH below 7, a basic pH above 7, and a neutral pH of 7. The text provides examples of calculating the pH from the hydronium ion concentration and vice versa using logarithmic calculations and rules for significant figures. It also gives sample problems identifying solutions as acidic, basic, or neutral based on their given pH or hydronium ion concentration values.
Wastewater treatment involves several stages to manage water discharged from homes, businesses, and industries. These stages include pre-treatment, preliminary treatment, primary treatment, secondary treatment, and sludge disposal. The goal is to reduce threats to water pollution by removing solid materials, decomposing organic matter with bacteria and algae, and further separating solids from treated water which is then discharged. Sludge is stabilized and applied to agricultural fields. The wastewater treatment plant laboratory conducts tests to monitor the effectiveness of the treatment process.
Wastewater treatment involves several stages to manage water discharged from homes, businesses, and industries. These stages include pre-treatment, preliminary treatment, primary treatment, secondary treatment, and sludge disposal. The goal is to reduce water pollution by decreasing levels of suspended solids and biochemical oxygen demand through physical and biological processes before water is discharged or sludge is land applied.
T cells can be categorized into several subsets including helper T cells, cytotoxic T cells, memory T cells, and regulatory T cells. Helper T cells assist other immune cells, cytotoxic T cells destroy infected and tumor cells, memory T cells provide faster responses upon reexposure to pathogens, and regulatory T cells suppress immune activation and prevent autoimmunity. Understanding regulatory T cells in HIV-1 could lead to new immunotherapy or vaccine strategies, but their exact role in HIV-1 pathogenesis requires further study.
The blood-brain barrier (BBB) is a membrane that controls the passage of substances from the blood into the central nervous system. It is a physical barrier between blood vessels and the central nervous system that stops many substances from passing through. The BBB is permeable to alcohol and some heavy metals but blocks most molecules that are larger than 500 Daltons from entering the brain. It protects the brain from common infections by preventing antibodies from crossing over. The BBB can be broken down by factors like hypertension, development, radiation exposure, infection, or trauma.
Introduction to treatment_of_tannery_effluentssafwan patel
This document provides an introduction to effluent treatment for tanneries. It discusses the objectives and methods for primary treatment, including screening, pumping, grit removal, equalization, chemical coagulation/flocculation, and primary sedimentation. It also covers secondary (biological) treatment using aerobic processes, advanced tertiary treatment options, sludge handling, odor control, and overall effluent treatment plant management. The goal is to help tanners understand wastewater treatment principles and regulations to reduce treatment costs and environmental impacts.
This document provides an overview of water treatment technologies from an Indian perspective. It discusses the objectives of water treatment, which include managing water discharge to reduce pollution and allow for reuse. It outlines various water quality parameters that are tested and regulated. It then describes common water treatment systems like ETPs and STPs, as well as the treatment processes involved in STPs, including pre-treatment, primary treatment, and secondary treatment. Key components of treatment systems like clarifiers, aeration tanks, and filters are illustrated. Advanced processes like reverse osmosis and desalination are also summarized. The document concludes by referencing several sources on water treatment practices.
Plan an ETP with detail process discussion following the instructionsMd Fahimuzzaman
Effluent is the stream of excess chemical liquor from an industry after using in original operation. For example, the excess dye liquor extracted from the textile industry after dyeing is an effluent of that dyeing industry. Effluent Treatment Plant or ETP is a waste water treatment method which is particularly designed to purify industrial waste water for its reuse and it’s aim is to release safe water to environment from the harmful effect caused by the effluent. Textile industry uses numerous hazardous chemicals during processing such as heavy metals, salts, surfactants, sulphite, and formaldehyde, which can cause major pollution in the effluents’ receiving waters. Since textile waste water contains a diversity of impurities and therefore specific treatment technology called ETP is required. The ETP Plant works at various levels and involves various physical, chemical, biological and membrane processes to treat waste water from different industrial sectors like chemicals, drugs, pharmaceutical, refineries, dairy, ready mix plants & textile etc.
Advanced tailing separation process - Minewaste 2010 -Peter Godwin
The document discusses methods for improving tailings treatment processes to generate additional profits through more complete material separation and water recycling. It presents a plant concept for treating coal tailings ponds that uses classification, flotation, filtration and drying to recover 80% of solids as a valuable product. Hyperbaric filtration is proposed as an alternative to vacuum filtration and drying to further reduce waste volumes and improve economics.
1) The document discusses cleaning needs for printed circuit boards (PCBs) and how they have evolved with trends like miniaturization and lead-free soldering. It evaluates different cleaning methods and products.
2) Key parameters that affect cleaning performance are solvent power, surface tension, temperature, agitation type, and process duration. The best performers are found to be co-solvent vapor degreasing processes using formulated hydrocarbons and hydrofluoroethers with ultrasonic or jet agitation.
3) Testing of various cleaning methods on sample PCBs found that co-solvent vapor degreasing using formulated hydrocarbons and hydrofluoroethers with ultrasonic agitation provided the
This document provides details on an environmental management plan project conducted in 1999-2000 for the CIB Refinery of ECOPETROL in Colombia. The project developed an environmental impact study and instructions to improve the refinery's environmental performance from 2000-2010. It involved assessing waste management practices and developing recommendations to align them with national and international standards. The author was contracted to build an environmental index to monitor waste disposal management at the refinery.
Performance Evaluation of Dairy Wastewater Treatment PlantIRJET Journal
1) The document analyzes the performance of a dairy wastewater treatment plant in Jaipur, India.
2) It evaluates various water quality parameters (BOD, COD, TSS, oil/grease) at the plant's inlet and outlet to assess the plant's ability to treat wastewater to regulatory standards.
3) The results show that the plant significantly reduces all parameters measured (BOD reduced from 1477 mg/L to 12 mg/L) and meets regulatory limits for treated water discharge.
The document provides an overview of membrane contactor technology from Membrana-Charlotte. It discusses the company and its products, including microporous membranes and membrane contactors. It describes how membrane contactors work using gas transfer principles and can be used for applications like gas absorption, degasification, and carbonation. Performance examples for oxygen and carbon dioxide removal are also presented.
This document summarizes testing of a new gas phase advanced oxidation (GPAO) system called Climatic for controlling pollution from foundries. Laboratory tests showed the system can remove common pollutants like benzene with removal rates varying based on reaction rate constants. An initial field test at a foundry effectively removed benzene but performance was impacted by varying pollution levels. A second larger field test effectively removed amines and tetraethyl silicate, achieving over 90% removal rates. The system uses UV light to generate hydroxyl radicals to oxidize pollutants in a fast and efficient manner suitable for treating large exhaust air flows.
Mobile sources of air pollution such as vehicles can be improved through cleaner fuels, fuel additives, and emission control devices. Two-way catalytic converters oxidize carbon monoxide and unburnt hydrocarbons, while three-way catalytic converters also reduce nitrogen oxides. Stationary sources use pre-combustion, combustion, and post-combustion controls. Particulate matter is controlled through gravitational settling chambers, cyclones, fabric filters, electrostatic precipitators, and wet collectors. The design and operation of these control devices depends on factors like particle size and concentration.
This document provides an overview of surface cleaning techniques and their role in reducing solvent emissions. It introduces improved cleaning technologies that can abate solvent use, such as enclosed cleaning machines and solvent recovery systems. Enclosed cleaning systems can reduce direct solvent emissions by over 90% compared to open systems, and solvent consumption by 60-80%. The latest generation of closed loop systems with vacuum technology achieve very low VOC emissions of under 0.1 kg/h. Adopting best practices like solvent recycling and recovery through distillation can recover up to 99.9% of solvents.
This document summarizes the characteristics and polluting effects of textile organic dyes, and procedures for separating and eliminating them from industrial effluents. It discusses that textile dyeing is a major source of organic water pollution worldwide. Textile dyes are recalcitrant and can remain in the environment for long periods. The document outlines the classification and characteristics of natural and synthetic textile dyes. It also describes common textile processing steps that generate large volumes of contaminated wastewater containing dyes, chemicals, and other pollutants. Current treatment methods aim to remove over 70% of contaminants like COD, BOD, dyes before wastewater discharge to meet environmental standards.
This document provides an overview of municipal and domestic wastewater treatment processes. It discusses the key microbial processes involved, including biodegradation, bioconversion, and removal/separation processes. Common treatment steps like primary settling, biological treatment, clarification and disinfection are outlined. Specific examples of wastewater treatment plants and processes, such as activated sludge reactors and anaerobic digestion, are also described. The document raises questions around optimizing microbial functions in wastewater treatment and recovering resources from wastewater.
Application on Semi-aerobic Landfill. Technology in in Tropical Climate: Lysi...CRL Asia
Presentation file on Application on Semi-aerobic Landfill. Technology in in Tropical Climate: Lysimeter experiment of Thailand (Created: SWGA Chart Chiemchaisri)
The document describes the S-Cube air treatment system from Active Clean Environmental Corporation. It contains details about the various components of the system and how it works to remove odors and other contaminants from air. The system uses a multi-stage approach including filters, scrubbers, plasma reactors, and ion clusters to purify air. Test results show the system can remove over 90% of malodors, volatile organic compounds, and other pollutants from industrial exhaust air.
This document discusses ozone and biologically active filtration for controlling disinfection byproducts in drinking water treatment. It provides an overview of ozone production, application, safety considerations, and operational design. Biologically active filtration is described as using the same rapid sand filtration concepts while also removing assimilable organic carbon through the establishment of biofilm. The document outlines pilot demonstrations and applications of these technologies in Ohio drinking water facilities.
Air Pollution Control Technology (Marble Industry)Saad Farooqi
This document discusses air pollution control technologies used in the marble industry. It describes how cyclones, electrostatic precipitators, fabric filters, and wet collectors work to remove particulate matter from exhaust gases. Cyclones use inertia to remove particles, electrostatic precipitators use charged plates to attract particles, fabric filters work like vacuum bags to trap particles, and wet collectors spray water to capture particles. The document compares the technologies' efficiencies at removing different sized particles and discusses controlling gaseous pollutants like sulfur dioxide and nitrogen dioxide from the marble industry.
This document provides an outline and overview of a presentation on controlling emissions of volatile organic compounds (VOCs) through biofiltration. It discusses VOCs emissions in Canada, traditional removal technologies and their limitations, and how biofiltration works as a green alternative. It then presents a case study of a commercial-scale biofiltration system used by a printed circuit board industry in Toronto to remove VOCs such as glycol and acetates from its air streams, achieving over 90% removal efficiency. The system used two biofilter units with different media that maintained effective operation even in winter.
Similar to Introduction to treatment_of_tannery_effluents (20)
Best 20 SEO Techniques To Improve Website Visibility In SERPPixlogix Infotech
Boost your website's visibility with proven SEO techniques! Our latest blog dives into essential strategies to enhance your online presence, increase traffic, and rank higher on search engines. From keyword optimization to quality content creation, learn how to make your site stand out in the crowded digital landscape. Discover actionable tips and expert insights to elevate your SEO game.
Programming Foundation Models with DSPy - Meetup SlidesZilliz
Prompting language models is hard, while programming language models is easy. In this talk, I will discuss the state-of-the-art framework DSPy for programming foundation models with its powerful optimizers and runtime constraint system.
“An Outlook of the Ongoing and Future Relationship between Blockchain Technologies and Process-aware Information Systems.” Invited talk at the joint workshop on Blockchain for Information Systems (BC4IS) and Blockchain for Trusted Data Sharing (B4TDS), co-located with with the 36th International Conference on Advanced Information Systems Engineering (CAiSE), 3 June 2024, Limassol, Cyprus.
Threats to mobile devices are more prevalent and increasing in scope and complexity. Users of mobile devices desire to take full advantage of the features
available on those devices, but many of the features provide convenience and capability but sacrifice security. This best practices guide outlines steps the users can take to better protect personal devices and information.
In his public lecture, Christian Timmerer provides insights into the fascinating history of video streaming, starting from its humble beginnings before YouTube to the groundbreaking technologies that now dominate platforms like Netflix and ORF ON. Timmerer also presents provocative contributions of his own that have significantly influenced the industry. He concludes by looking at future challenges and invites the audience to join in a discussion.
Full-RAG: A modern architecture for hyper-personalizationZilliz
Mike Del Balso, CEO & Co-Founder at Tecton, presents "Full RAG," a novel approach to AI recommendation systems, aiming to push beyond the limitations of traditional models through a deep integration of contextual insights and real-time data, leveraging the Retrieval-Augmented Generation architecture. This talk will outline Full RAG's potential to significantly enhance personalization, address engineering challenges such as data management and model training, and introduce data enrichment with reranking as a key solution. Attendees will gain crucial insights into the importance of hyperpersonalization in AI, the capabilities of Full RAG for advanced personalization, and strategies for managing complex data integrations for deploying cutting-edge AI solutions.
UiPath Test Automation using UiPath Test Suite series, part 6DianaGray10
Welcome to UiPath Test Automation using UiPath Test Suite series part 6. In this session, we will cover Test Automation with generative AI and Open AI.
UiPath Test Automation with generative AI and Open AI webinar offers an in-depth exploration of leveraging cutting-edge technologies for test automation within the UiPath platform. Attendees will delve into the integration of generative AI, a test automation solution, with Open AI advanced natural language processing capabilities.
Throughout the session, participants will discover how this synergy empowers testers to automate repetitive tasks, enhance testing accuracy, and expedite the software testing life cycle. Topics covered include the seamless integration process, practical use cases, and the benefits of harnessing AI-driven automation for UiPath testing initiatives. By attending this webinar, testers, and automation professionals can gain valuable insights into harnessing the power of AI to optimize their test automation workflows within the UiPath ecosystem, ultimately driving efficiency and quality in software development processes.
What will you get from this session?
1. Insights into integrating generative AI.
2. Understanding how this integration enhances test automation within the UiPath platform
3. Practical demonstrations
4. Exploration of real-world use cases illustrating the benefits of AI-driven test automation for UiPath
Topics covered:
What is generative AI
Test Automation with generative AI and Open AI.
UiPath integration with generative AI
Speaker:
Deepak Rai, Automation Practice Lead, Boundaryless Group and UiPath MVP
TrustArc Webinar - 2024 Global Privacy SurveyTrustArc
How does your privacy program stack up against your peers? What challenges are privacy teams tackling and prioritizing in 2024?
In the fifth annual Global Privacy Benchmarks Survey, we asked over 1,800 global privacy professionals and business executives to share their perspectives on the current state of privacy inside and outside of their organizations. This year’s report focused on emerging areas of importance for privacy and compliance professionals, including considerations and implications of Artificial Intelligence (AI) technologies, building brand trust, and different approaches for achieving higher privacy competence scores.
See how organizational priorities and strategic approaches to data security and privacy are evolving around the globe.
This webinar will review:
- The top 10 privacy insights from the fifth annual Global Privacy Benchmarks Survey
- The top challenges for privacy leaders, practitioners, and organizations in 2024
- Key themes to consider in developing and maintaining your privacy program
Unlocking Productivity: Leveraging the Potential of Copilot in Microsoft 365, a presentation by Christoforos Vlachos, Senior Solutions Manager – Modern Workplace, Uni Systems
Dr. Sean Tan, Head of Data Science, Changi Airport Group
Discover how Changi Airport Group (CAG) leverages graph technologies and generative AI to revolutionize their search capabilities. This session delves into the unique search needs of CAG’s diverse passengers and customers, showcasing how graph data structures enhance the accuracy and relevance of AI-generated search results, mitigating the risk of “hallucinations” and improving the overall customer journey.
GraphSummit Singapore | The Future of Agility: Supercharging Digital Transfor...Neo4j
Leonard Jayamohan, Partner & Generative AI Lead, Deloitte
This keynote will reveal how Deloitte leverages Neo4j’s graph power for groundbreaking digital twin solutions, achieving a staggering 100x performance boost. Discover the essential role knowledge graphs play in successful generative AI implementations. Plus, get an exclusive look at an innovative Neo4j + Generative AI solution Deloitte is developing in-house.
Why You Should Replace Windows 11 with Nitrux Linux 3.5.0 for enhanced perfor...SOFTTECHHUB
The choice of an operating system plays a pivotal role in shaping our computing experience. For decades, Microsoft's Windows has dominated the market, offering a familiar and widely adopted platform for personal and professional use. However, as technological advancements continue to push the boundaries of innovation, alternative operating systems have emerged, challenging the status quo and offering users a fresh perspective on computing.
One such alternative that has garnered significant attention and acclaim is Nitrux Linux 3.5.0, a sleek, powerful, and user-friendly Linux distribution that promises to redefine the way we interact with our devices. With its focus on performance, security, and customization, Nitrux Linux presents a compelling case for those seeking to break free from the constraints of proprietary software and embrace the freedom and flexibility of open-source computing.
Essentials of Automations: The Art of Triggers and Actions in FMESafe Software
In this second installment of our Essentials of Automations webinar series, we’ll explore the landscape of triggers and actions, guiding you through the nuances of authoring and adapting workspaces for seamless automations. Gain an understanding of the full spectrum of triggers and actions available in FME, empowering you to enhance your workspaces for efficient automation.
We’ll kick things off by showcasing the most commonly used event-based triggers, introducing you to various automation workflows like manual triggers, schedules, directory watchers, and more. Plus, see how these elements play out in real scenarios.
Whether you’re tweaking your current setup or building from the ground up, this session will arm you with the tools and insights needed to transform your FME usage into a powerhouse of productivity. Join us to discover effective strategies that simplify complex processes, enhancing your productivity and transforming your data management practices with FME. Let’s turn complexity into clarity and make your workspaces work wonders!
Building Production Ready Search Pipelines with Spark and MilvusZilliz
Spark is the widely used ETL tool for processing, indexing and ingesting data to serving stack for search. Milvus is the production-ready open-source vector database. In this talk we will show how to use Spark to process unstructured data to extract vector representations, and push the vectors to Milvus vector database for search serving.
2. Introduction to treatment
of tannery effluents
UNITED NATIONS INDUSTRIAL DEVELOPMENT ORGANIZATION
Vienna, 2011
What every tanner should know
about effluent treatment
5. Table 1. An example of mass balance in leather processing
Table 2. An example of average total pollution load
Table 3. An example of pollution load, conventional process
Table 4. Purification efficiency of treatment stages referred to raw effluent
Table 5. Characteristics of sludge dewatering equipment
Table 6. Dry matter content in sludge
Table 7. Poisoning effects of hydrogen sulphide gas (H2S)
Figure 1. Overview of the tanning industry
Figure 2. Sources and types of pollutants generated in leather processing
Figure 3. Layout of in-house segregation of streams
Figure 4. Flowchart of in-house segregation of streams
Figure 5. Rough bar screen, side view
Figure 6. Rough bar screen, operation principle
Figure 7. Simple, non-aerated grit-and-floating-matter removal chamber
Figure 8. Self-cleaning, rotary-brush screen, Parkwood type
Figure 9. Self-cleaning screen, hydrosieve type
Figure 10. Submersible pump
Figure 11. Archimedes lifting pump
Figure 12. Rotary-drum (Konica) screen, outer flow
Figure 13. Rotary-drum fine screen, inner flow
Figure 14. Schematic view of an equalization, homogenization tank
Figure 15. Venturi-type ejector often installed for mixing and aeration in the homogenization tank
Figure 16. Schematic view of the coagulation and flocculation system
Figure 17. Some simple laboratory utensils
Figure 18. Cross section of a typical circular sedimentation tank
Figure 19. Cross section of a rectangular sedimentation tank
Figure 20. Schematic view of a dissolved-air flotation (DAF) unit
Figure 21. Cross section of a progressing cavity pump for sludge transfer
Figure 22. Cross section of a gravity thickener
Figure 23. Cross section of a recessed-plate press for sludge dewatering
Figure 24. Cross section of a belt-type press for sludge dewatering
Figure 25. Cross section of a sludge dewatering centrifuge
Figure 26. Schematic views of sludge-drying beds
Figure 27. Simplified flowchart of the physical-chemical (primary) tannery effluent treatment
Figure 28. A simplified flow diagram of the activated sludge process
Figure 29. Surface (floating) aerators
Figure 30. Cross section of floating aerator
Figure 31. Forced-air, submersed turbine aerator
Figure 32. Schematic diagram of oxidation ditches
Figure 33. Simplified flowchart of the biological (secondary) tannery effluent treatment
4 Contents
7
7
9
27
37
38
44
6
8
10
10
12
13
13
14
14
15
15
16
16
17
18
19
20
21
21
22
23
23
24
25
26
27
28
30
32
33
33
35
40
Tables
Figures
6. Figure 34. Simplified flowchart of a full-fledged tannery effluent treatment plant
Figure 35. Structure of average treatment costs at selected CETPs in India in 2005
Figure 36. Distribution of average total costs at selected CETPs in Italy
Figure 37. Schematic chart of typical effluent treatment setup for clusterss in developing countries
Figure 38. Schematic chart of typical effluent treatment setup in industrialized countries
Figure 39. An example of CETP management setup
Photo 1. Coagulant/flocculant dosing station
Photo 2. "Flocs" after coagulation, flocculation
Photo 3. Sedimentation tank (empty)
Photo 4. Sedimentation tank in operation
Photo 5. Recessed-plate filter press with container for dewatered sludge
Photo 6. Belt press with transporter for dewatered sludge
Photo 7. Sludge dewatering centrifuge (the lid is up for better view)
Photo 8. Surface aerators
Photo 9. Bottom air diffuser grid with one section and fine-bubble dome diffuser
Photo 10. Fine-bubble difusers, dome and tubular type
Photo 11. Submersed turbine aerators in oxidation ditch
Photo 12. Oxidation ditch in operation
Photo 13. Containers for solid waste
Annex 1. General view of inputs and outputs in the leather sector
Annex 2. Chrome-recovery unit using NaOH
Annex 3. Classification of pumps
Annex 4. A model of rotary screening drum
Annex 5. Types of sedimentation tanks
Annex 6. Photos and cross section of a circular sedimentation tank
Annex 7. Sludge production in leather processing
Annex 8. Classification of mechanical aerators
Annex 9. Scheme of the membrane bioreactor (MBR)
Annex 10. Personal hydrogen-gas monitor
Annex 11. Reverse osmosis (RO): principle, diagram, photo of a small RO unit
Annex 12. Schematic view of constructed wetland – reed beds
Annex 13. Aerated static composting pile
Annex 14. Typical fluxogram of an ETP
Annex 15. A dialogue between a tanner and an environmental engineer
Annex 16. Basic plant monitoring and control
Annex 17. Discharge limits for treated tannery effluents in France, Italy and India
Annex 18. Typical tannery ETP auxiliary chemicals and their dosing
Annex 19. Environmental effects of the main constituents of tannery effluents
Annex 20. References
Introduction to treatment of tannery effluents 5
41
42
42
43
43
45
20
20
22
22
24
25
26
33
34
34
35
36
38
48
48
49
50
50
51
51
52
53
53
54
55
56
57
58
59
60
61
62
67
Photographs
Annexes
7. Confronted with increasing legal and social pressures, no tanner can afford the luxury of not being
familiar with the main issues and principles of environmental protection pertaining to tannery operations.
Obviously, pollution prevention, the persistent promotion of cleaner leather processing, which ultimately
leads to lower treatment costs, remains the supreme priority.
By applying industrially proven low-waste advanced methods such as the use of salt-free preserved raw
hides and skins, hair-save liming, low-ammonia or ammonia-free deliming and bating, advanced chrome
management systems, etc., it is possible to decrease significantly the pollution load, namely: COD and
BOD5 by more than 30%, sulphides by 80-90%, ammonia nitrogen by 80%, total (Kjeldahl) nitrogen by
50%, chlorides by 70%, sulphates by 65%, and chromium by up to 90%.
Yet, despite all preventive measures, there is still a considerable amount of pollution load to be dealt with
by end-of-pipe methods.
The purpose of this booklet is to help tanners and tannery managers get acquainted with basic principles
and methods of tannery effluent treatment. This knowledge should make them better equipped for a
dialogue with the factory's own environmental unit, environmental authorities and NGOs.
In order to keep it short and concise, there are many simplifications and omissions of details; therefore,
for an in-depth understanding of the complexities of dealing with effluents and solid wastes (sludge), it
is recommended to consult the extensive literature on this subject.
Finally, there is the widespread misperception that vegetable tanning is environmentally harmless (in
reality its effluents have very high, difficult to treat COD); this publication focuses on combined chrome
tanning, which is by far the most prevailing leather tanning method.
6 Why this booklet?
Figure 1. Overview of the tanning industry
Foreword: Why this booklet?
8. Cleaner technologies
The pressure to adopt cleaner technologies normally emanates from environmental imperatives such as the
need to meet specific discharge norms, reduce treatment costs or comply with occupational safety and
health standards. The typical primary targets are: lower water consumption, improved uptake of chemicals,
better quality/re-usability of solid waste, and reduced content of specific pollutants such as heavy metals
and electrolytes.
The spread of cleaner technologies and processes has been neither spontaneous nor extensive. For all the
claims about favourable cost-benefit ratios and/or environmental benefits to be derived from many of these
technologies, tanners are not quick in adopting them, be it due to inertia, higher costs or the limitations
mentioned earlier.
Pollution load
Due to variations in raw material, process, chemicals, water consumption, etc., it is small wonder that figures
about pollution load in the literature vary a lot and should be interpreted very cautiously. The tables below
and the chart on overleaf may give a general idea, the usual reference being one tonne of wet-salted hides.
Introduction to treatment of tannery effluents 7
Table 1. An example of mass balance in leather processing
Table 2. An example of average total pollution load – concentration in combined raw effluent,
conventional process, water consumption: 45 m3/tonne
9. 8 Why this booklet?
Figure 2. Sources and types of pollutants generated in leather processing
10. Introduction to treatment of tannery effluents 9
To avoid possible confusion arising due to differences in water consumption, it is practical to indicate the
amount of pollutants generated per tonne of raw-hide input. While generally lower water consumption is
very desirable (nowadays in well managed tanneries, it is below 30 m3/tonne), it obviously results in
considerably higher concentrations of pollutants.
Treatment
Before turning to treatment itself, it is important to bear in mind the following:
• The design of an effluent treatment plant (ETP) is always tailored to the requirements of a specific site;
thus, there are no two identical ETPs.
• Pollutants contained in effluent cannot disappear; they are only converted into something which is
environmentally more acceptable or easier to dispose of (sludge).
• Somewhat paradoxically, the obvious is often overlooked: the same amount of pollutants at lower water
consumption means lower hydraulic load (volume) but higher concentration – not always easy to treat.
• It is important for a tanner to understand the relation between the leather technologies applied and
wastewater treatment in order to reduce the overall cost of treatment.
Wastewater treatment is a multi-stage process to purify wastewater before it enters a body of natural water,
or it is applied to the land, or it is reused. The goal is to reduce or remove organic matter, solids, nutrients,
Cr and other pollutants since each receiving body of water can only receive certain amounts of pollutants
without suffering degradation. Therefore, each effluent treatment plant must adhere to discharge standards
– limits usually promulgated by the relevant environmental authority as allowable levels of pollutants, for
practical reasons expressed as BOD5, COD, suspended solids (SS), Cr, total dissolved solids (TDS) and
others. The three main categories of tannery wastewater, each one having very distinctive characteristics, are:
• Effluents emanating from the beam-house – liming, deliming/bating, water from fleshing and splitting
machines; they contain sulphides, their pH is high, but they are chrome-free.
• Effluents emanating from the tanyard (tanning and re-tanning, sammying) – high Cr content, acidic.
• Soaking and other general effluents, mainly from post-tanning operations (fat-liquoring, dyeing) – low
Cr content.
Table 3. An example of pollution load, conventional process
11. 10 Why this booklet?
Figure 3. Layout of in-house segregation of streams,
including chrome recycling and oxidation of sulphides in liming effluent
Figure 4. Flowchart of in-house segregation of streams,
including chrome recycling, treatment of liming effluents and pre-treatment of mixed effluent
12. Introduction to treatment of tannery effluents 11
It is very important to segregate these streams and to pre-treat them separately according to their characteri-
stics to avoid possible safety risks (formation of deadly hydrogen sulphide) and to reduce the cost of
treatment and sludge disposal (to avoid contamination of sludge with Cr). The mixing of liming and tan-
ning streams gives rise not only to the obnoxious smell typical of poorly managed tanneries; the resulting
lethally poisonous gas, hydrogen sulphide (H2S), is still by far the most frequent killer in tannery
accidents, which occur mainly in inadequately ventilated spaces, especially in pits and channels.
The volume and pollution load of sanitary wastewater in comparison with industrial wastewater is
insignificant.
Very arbitrarily and not quite consistently we speak of the following main phases of treatment:
Preliminary treatment
Typically, in the case of common effluent treatment plants (CETPs) servicing tannery clusters often found
in developing countries, it is essential to have pre-treatment units installed in individual tanneries. Their
role is to remove large particles, sand/grit and grease, but also to significantly reduce the content of chrome
and sulphides before the effluent is discharged into the collection network.
Physical-chemical treatment (primary)
The objective here is the removal of settleable organic and inorganic solids by sedimentation, and the
removal of materials that will float (scum) by skimming. Approximately 25-50% of the incoming bio-
chemical oxygen demand (BOD5), 50-70% of total suspended solids (SS), and 65% of the oil and
grease are removed during primary treatment. The effluent and sludge from primary sedimentation are
referred to as primary effluent and sludge.
Biological treatment (secondary)
In most cases, secondary treatment follows primary treatment, its goal being the removal of biodegradable
dissolved and colloidal organic matter using aerobic biological treatment processes. Aerobic biological
treatment is carried out in the presence of oxygen by aerobic micro-organisms (principally bacteria) that
metabolize the organic matter in the wastewater, thereby producing more micro-organisms and inorganic
end products (principally CO2, NH3, and H2O). Several aerobic biological processes are used for secondary
treatment and the differences among them have to do primarily with the manner in which oxygen is
supplied to the micro-organisms and with the rate at which organisms metabolize the organic matter.
Advanced (tertiary) treatment
Tertiary or advanced wastewater treatment is employed to reduce residual COD load and/or when specific
wastewater constituents are not removed by previous treatment stages.
Sludge handling and disposal
Effluent treatment plants produce treated, “cleaned” effluent and sludge because inherently the primary
aim of wastewater treatment is the removal of solids and some potentially hazardous substances from the
wastewater. Furthermore, biologically degradable organic substances are converted into bacterial cells,
and the latter are removed from the wastewater.
13. 12 Primary treatment
Figure 5. Rough bar screen, side view
1.1 Objectives
• To eliminate the coarse material normally present in the raw wastewater that could clog/block pumps,
pipes and possibly sewer lines.
• To mix and balance well different tannery streams and thus produce homogenized “raw material” that
can be treated in a consistent manner.
• To adjust pH and eliminate toxic substances (sulphides) and avoid shock loads that can negatively affect
the rather sensitive biological treatment.
• To significantly decrease the BOD/COD load and thus simplify the biological treatment phase and reduce
its cost.
To summarize, the purpose is to eliminate the coarse matter, remove almost completely Cr and sulphides,
remove the major part of suspended solids, and considerably reduce the BOD and COD content.
Basic steps:
Screening (bar, self-cleaning)1
Pumping/lifting
Fine screening
Equalization and sulphide oxidation
Chemical treatment (coagulation, flocculation)
Settling
Sludge dewatering2
1.2 Screening
1.2.1 Bar screening, removal of larger solids
1Quite often a grease-and-sand trap is also included, usually before fine screening and pumping.
2 Primary and secondary sludge are handled/dewatered together; however, since some ETPs have only primary treatment
and the main part of sludge is generated during that stage, sludge dewatering is covered here.
1. Primary treatment
14. Introduction to treatment of tannery effluents 13
Figure 7. Simple, non-aerated grit-and-floating-matter removal chamber
Figure 6. Rough bar screen, operation principle
1.2.2 Removal of grit and floating matter
A simple, non-aerated grit-and-floating-matter removal chamber is usually placed in a horizontal
gravity channel immediately after the rough screen.
Large ETPs require more sophisticated, aerated systems for the removal of grit and floating matter.
15. 14 Primary treatment
Figure 8. Self-cleaning, rotary-brush screen, Parkwood type
Figure 9. Self-cleaning screen, hydrosieve type
1.2.3 Self-cleaning screens
1.3 Pumping/lifting
It is not possible to transfer effluents throughout the ETP by gravity only; at least one, often more
pumping/lifting stations are needed, the first typically located before the rotary screen. Depending on specific
requirements (capacity/flow), different types of pumps are used. For medium-scale ETPs, submersible pumps
are generally used for this purpose, for large-volume ones, screw (Archimedes) pumps are preferred.
16. Introduction to treatment of tannery effluents 15
Figure 11. Schematic view of an Archimedes-type lifting pump
Figure 10. Submersible pump
The scheme of submersible pump positioning (usually with a stand-by pump) is shown below:
1.3.1 Submersible pump
1.3.2 Screw (Archimedes) pump
17. 16 Primary treatment
Figure 12. Rotary-drum (Konica) screen, outer flow
Figure 13. Rotary-drum fine screen, inner flow
1.4. Fine screening
Fine screening should drastically reduce the amount of fine suspended solids. The figures below show
rotary-drum screens with outer and inner flow.
18. Introduction to treatment of tannery effluents 17
Figure 14. Schematic view of an equalization, homogenization tank
1.5 Equalization – homogenization – sulphide oxidation
The main aims here are:
• homogenization of the effluent (quantity and quality); and
• sulphide elimination, mostly by catalytic oxidation.
It is very important to keep all particulate matters in suspension, i.e., to avoid settling of solids. This is
achieved by using mixing-cum-aeration devices such as diffused-air systems (preferred),Venturi ejectors, and
fixed or floating aerators (lately avoided due to lower efficiency and the problem of aerosols). In practice, to
play it safe, the volume of the equalization tank corresponds to the total daily effluent discharge.
Approximately 1 kg of O2 is needed to oxidize 1 kg of S2- to thiosulphate, whereas the oxygen transfer
efficiency is about 1.5 kg O2/kWh (simplified approximation: 1 kg S2- = 1 kg O2 = 1kWh). Again, in
practice, attention is focused on the energy required to keep the solids in suspension (some 50 W/m3),
which is then sufficient for sulphide oxidation; the amount of catalyst, MnSO4 · 4 H2O, industrial purity,
is about 20 g per cubic meter of tank capacity.
Whichever the mixing/aeration system chosen, it is necessary to be possible to remove the mixing device
without stopping the treatment process. The inlet and the outlet of the equalization tank should be as far
away from each other as possible to allow proper mixing (and no short-circuiting).
19. 18 Primary treatment
Figure 15. Venturi-type ejector often installed for mixing and aeration in the homogenization tank
A typical equalization tank will have transfer pumps for equalized effluent. The capacity of the pumps is
based on tank capacity, transfer time and head. One pump of cast iron with inside parts of stainless steel and
one stand-by pump are sufficient unless effluent volume is very high (say 1,500 m3/d or more). The pumping
line(s) are also a good place to set an electro-magnetic flow meter.
1.6 Chemical treatment (coagulation, flocculation)
Chemicals are added in order to improve and accelerate the settling of suspended solids, especially of fine
and colloidal matter.
In wastewater treatment operations, the processes of coagulation and flocculation are employed to separate
suspended solids from water. These terms are often used interchangeably, or the single term – be it “coagu-
lation” or “flocculation” – is used to describe both; sometimes “flocculation” is understood as the second
stage of “coagulation”. In fact, they are two distinct processes usually carried out in sequence as a combina-
tion of physical and chemical procedures. Finely dispersed solids (colloids) suspended in wastewater are
stabilized by negative electric charges on their surfaces, causing them to repel each other. Since this prevents
these charged particles from colliding to form larger masses, called flocs, they do not settle.
Coagulation is the destabilization of colloids by neutralizing the forces that keep them apart. Cationic
coagulants provide positive electric charges to reduce the negative charge (zeta potential) of the colloids. As
a result, the particles collide to form larger particles (flocs). Rapid mixing is required to disperse the
coagulant throughout the liquid. Care must be taken not to overdose the coagulants as this can cause
a complete charge reversal and thus re-stabilize the colloid complex.
20. Introduction to treatment of tannery effluents 19
Figure 16. Schematic view of the coagulation and flocculation system
Flocculation is the action of polymers to form bridges between flocs and bind particles into large
agglomerates or clumps. In this process it is essential that the flocculating agent be added by slow and gentle
mixing to allow for contact between the small flocs and to agglomerate them into larger particles. The newly
formed agglomerated particles are quite fragile and can be broken apart by shear forces during mixing. Care
must also be taken not to overdose the polymer as doing so will cause settling/clarification problems.
Once suspended particles are flocculated into larger particles, they can usually be removed from the
liquid by sedimentation, filtration, straining or floatation. The flocculation reaction not only increases
the size of floc particles in order to settle them faster, but also affects the physical nature of flocs
making them less gelatinous and thereby easier to dewater.
The inorganic coagulants are compounds that break colloidal suspensions and help floc forming. The
most frequently used coagulants in tannery effluent treatment are:
- alum: industrial aluminium sulphate Al2(SO4)3 · 18H2O
- iron sulphate: industrial FeSO4 · 7H2O
- iron chloride: industrial FeCl3 · 6H2O
- lime: industrial calcium hydroxide Ca(OH)2
Coagulant aid – flocculants – are water-soluble organic (anionic) polyelectrolytes that support agglomeration
of colloidal and very fine suspended matter thus enhancing the impact of coagulation.
21. 20 Primary treatment
Figure 17. Some simple laboratory utensils
Photo 1. Coagulant/flocculant dosing station Photo 2. “Flocs” after coagulation-flocculation
For optimal results, appropriate dosing is essential; it should not be overlooked that, in addition to costs,
these chemicals also influence not only pH (acidification) but also TDS. On-the-spot investigation – jar
tests using either sophisticated apparatus or simple tools (shown below) – is a must.
Chemicals (pre)dissolved in small tanks with stirrers are usually added in the flash mixers – special “boxes”
for rapid mixing placed before the primary settling tank. The contact time in the flash mixer is about 5
minutes for coagulation and some 20 minutes for flocculation; in the latter case, slow mixing to avoid floc
shearing is essential. Hence, for example, if the capacity of the equalized effluent transfer pump is 60 m3/h,
the usable volume of the coagulation and flocculation tank respectively should be 60 · 1/12 = 5 m3 and
60 · 1/3 = 20 m3.
Ideally, two tanks should be available for the preparation of each chemical – one for solution preparation,
the other for feeding the solution to the effluent. By having two tanks, levels of chemical dosing can be
better controlled. The feeding of chemicals is done by dosing pumps.
22. Introduction to treatment of tannery effluents 21
Figure 18. Cross section of a typical circular sedimentation tank
Figure 19. Cross section of a rectangular sedimentation tank
with travelling bridge shown in two positions
1.7 Settling – primary sedimentation
The main objective at this stage is the removal of suspended solids; however, various constituents such as
fats, waxes, mineral oils, floating non-fatty materials, etc. (“grease”), not already removed in the grit-and-
oil chamber (usually positioned between screening and equalization), are also separated here.
Primary settling tanks (clarifiers) are either circular (more commonly used) or rectangular with continuous
grease (scum) removal at the top and sludge removal at the bottom. The key design parameters are:
• detention time – usually 1 to 2 hours (vertical clarifiers of the Dortmund type);
• surface hydraulic loading, expressed in m3/m2 of tank surface per hour or m/h, typically 1 to 2
m3/m2 per hour;
• surface solids rate, expressed in kg/m2 and indicating the quantity of SS crossing the surface area
of the tank over a certain time span (hour, day).
The surface solids rate is most frequently used in the design of sludge thickeners but, due to the quantity
(4-6 g/l) and flocculent nature of tannery effluent solids, it is useful in controlling the primary sedimenta-
tion as well. Circular tanks are generally preferred as recirculation is easier. A mechanical device (scraper)
is necessary in larger settling tanks.
23. 22 Primary treatment
Figure 20. Schematic view of a dissolved-air flotation (DAF) unit
Photo 3. Sedimentation tank (empty) Photo 4. Sedimentation tank in operation
In some cases, mainly due to space shortage, solids are removed by flotation, usually by the dissolved-air
flotation (DAF) system.
1.8 Sludge dewatering
The sludge drawn from the bottom of the tank is in the form of slurry with a dry-solid (DS) content of only
2-4%. For its evacuation, special pumps – usually of the Mohno type – are used.
24. Introduction to treatment of tannery effluents 23
Figure 21. Cross section of a progressing cavity pump for sludge transfer
Figure 22. Cross section of a gravity thickener
For further handling and disposal of sludge, it is necessary to reduce drastically the water content. This is
usually achieved by: (i) thickening in sludge thickeners (very much like circular clarifiers); (ii) mechanical
dewatering in filter presses, belt-filter presses or decanters (centrifuges); (iii) natural drying in sludge-drying
beds. In addition to power and chemical requirements, the key parameter for equipment selection is the
achievable dry matter content in the dewatered sludge.
1.8.1 Sludge thickener
The construction of the sludge thickener is in practice identical with that of the sedimentator although in
some cases the Dortmund type with self-desludging slopes is also used.
25. 24 Primary treatment
Figure 23. Cross section of a recessed-plate press for sludge dewatering
Photo 5. Recessed-plate filter press with container for dewatered sludge
26. Introduction to treatment of tannery effluents 25
Photo 6. Belt press with transporter for dewatered sludge
Figure 24. Cross section of a belt-type press for sludge dewatering
1.8.2 Belt-filter press
27. 26 Primary treatment
Figure 25. Cross section of a sludge dewatering centrifuge
Photo 7. Sludge dewatering centrifuge (the lid is up for a better view)
1.8.3 Centrifuge
By increasing dewatering level, improving wear and tear resistance (especially in the case of sludge
containing fine sand) as well as by lowering irritating noise, centrifuges have succeeded in conquering
a lot of ground in the treatment of tannery effluents.
Mechanical dewatering effects are nowadays from 30 to 40% DS, depending on initial concentration,
chemical preconditioning and equipment make.
28. Introduction to treatment of tannery effluents 27
Figure 26. Schematic views of sludge-drying beds
Table 4. Purification efficiency of treatment stages referred to raw effluent
1.8.4 Sludge-drying beds
Easily constructed with locally available materials, drying beds were perceived as the best solution for tan-
neries in hot-climate developing countries. However, they require a lot of area, the output during rainy
seasons drops considerably, there is the problem of malodour, they are not easy to clean and made ready for
the next batch, etc. For these reasons, sludge-drying beds are still used mainly by small tanneries not close to
residential areas and/or as fall-back units used during breakdowns of mechanical dewatering equipment.
The products of primary treatment are: (i) primary treated effluent – overflow from the primary settling tank –
with only residual amounts of chrome and sulphide and significantly reduced BOD, COD and SS content; and
(ii) dewatered sludge – with approximately 40% DS; its chrome content depends on the type and efficiency
of the chrome management system applied.
For the fortunate tanneries coupled to the sewage system, on-site treatment ends here – the biological treat-
ment takes place together with urban wastewater in large WWWs. Usually, industrial effluents are only a
small fraction of the total volume so that the salinity (TDS) they bring along does not represent a problem.
* Approximately at the load level of 0.30 kg BOD5/kg MLSS, oxygen requirement of 2.0 kg O2/kg BOD5 and MLSS 3300 g/m3
30. Introduction to treatment of tannery effluents 29
2.1 Objective and basic principles
The main objective at this stage is to further reduce the amount of organic (expressed as BOD and
COD)3 and other substances still present in the effluent after the primary treatment and thereby satisfy
the standards/limits for discharge into surface waters (rivers, lakes).
The biological treatment duplicates processes that take place in nature, but under controlled conditions
and, especially, at a highly accelerated pace; however, the efficiency of this treatment largely depends
on the biodegradability of the polluting substrate, i.e., its inherent capacity to decompose by biological
processes. The remaining suspended and colloidal solids are removed by flocculation and adsorption.
While biological treatment may be aerobic, facultative or anaerobic (or some combination thereof), in
practice, almost only aerobic systems are used; exceptionally, in countries with a hot climate and
where a lot of land is available, facultative (preferably aerated/facultative) lagoons are also used.
Due to the inherent characteristics of tannery effluents, primarily their sulphide/sulphate content, in
practice, anaerobic treatment is used only in sludge digestion.
Among many variations of the aerobic process, the most widely used method is (complete-mix) activated
sludge treatment with extended aeration; despite some very interesting features, membrane bioreactors
(MBRs) have not made significant inroads in the tanning sector.
The activated sludge process is an aerobic, biological process, which uses the metabolism of micro-
organisms to remove substances causing oxygen demand. The qualitative biochemical reaction taking
place in the organic matter stabilization process can be summarized in the following manner:
Inert matter + organic matter + oxygen + nutrients + micro-organisms
new micro-organisms + CO2 + H2O + additional inert matter
Simply said, we stimulate micro-organisms to convert (eat and digest) harmful, oxygen-demanding organic
compounds into an environmentally more acceptable form (micro-organisms) and low-energy, stable com-
pounds like water and carbon dioxide.
The microbial community that does that job comprises various species of bacteria, fungi, protozoa,
sometimes rotifers (multicellular animals only found in very stable activated sludge with long retention
times), even nematodes, the composition of the population depending on a plethora of factors.
3 Let us recall that BOD is defined as the quantity of oxygen required during the stabilization
of decomposable organic and oxidizable inorganic matter by aerobic biological action under standard conditions,
usually over only five days instead of 20. The manometric method is even faster but less accurate and reliable.
COD is the quantity of oxygen consumed for the total oxidation of the oxidizable matter (organic and inorganic)
with dichromate as the oxidizing agent. The COD is always greater than its BOD.
2. Biological (secondary) treatment
31. 30 Secondary treatment
Figure 28. A simplified flow diagram of the activated sludge process
Generally, the biological stage is the most complex part of the overall effluent treatment process, with
highest investment and operational costs, its day-to-day running requiring considerable skills and
experience.
2.2 Main operational parameters
The main operational parameters – expressions important to understanding the process – are:
• Total influent volume, Q: volume of treated effluent (m3/day)
• Tank volume, V: aeration tank volume (m3)
• Organic loading, F: total BOD5 applied (kg/day)
F = (f x Q)/1,000
where f is the BOD5 of the influent (mg/l)
• Mixed liquor suspended solids, M:
M = (MLSS x V)/1000
where MLSS is the concentration of SS
in mixed liquor in the aeration tank (mg/l)
• Loading factor, F/M: BOD5 kg per day per kg of mixed liquor suspended
solids (MLSS) in the aeration tank (mg/l)
• Hydraulic retention time, T:
T = (V/Q) x 24
where V is aeration tank volume (m3)
A uniform inlet flow over the entire day provides optimum conditions for absorbing the effect of possible
peaks of organic load or toxic substances (shock loads) and enhancing the efficiency of secondary
sedimentation.
The BOD here is in practice taken to represent the amount of food provided to the micro-organisms
contained in the system. Due to the difficulty of obtaining reliable BOD5 values, COD is sometimes used.
32. Introduction to treatment of tannery effluents 31
Hydraulic retention time is actually the average time (in hours) the influent spends passing through the
aeration tank; the extended aeration process, typical for tannery effluents, is usually longer than 24
hours.
Extended aeration plants are characterized by the introduction of wastewater directly into the reactor
basin, long aeration, high sludge return ratio, low sludge wastage and high MLSS: the F/M (kg BOD/kg
MLSS per day) ratio is only ≤ 0.05 – 0.1 in contrast to the conventional (0.15-0.4) or high-load type (0.4-1.0).
The F/M, the food to biomass (floc) ratio is a parameter crucial for operational conditions and the per-
formance of the biological process; regrettably, it cannot be determined quickly, on-the-spot.
2.3 Other operational parameters
Quite important are also parameters like the sludge age expressed as the mean cell-residence time
(MCRT), generally not less that 20 days, and the return activated sludge (RAS) – the volume of settled bio-
logical sludge recycled to the aeration tank as a percentage of the influent volume Q; in the extended aera-
tion process, it is about 80-100%.
The following parameters are, in particular, regularly monitored:
Dissolved oxygen (DO) is the content of molecular oxygen in the aeration tank (mg/l); it is one of the
most important factors determining the efficiency/performance of wastewater biological treatment.
Extended aeration units are usually operated in such a way as to keep the DO of the mixed liquor at
about 2 mg/l.
pH. The optimum pH range for aerobic processes is between 7.0 and 7.5 with an effective process
range of 6-9. In alkaline wastes, the reaction with CO2 produced by respiration neutralizes the excess
alkali, making addition of acid unnecessary. Adjustment with lime or other alkali becomes necessary
only if pH drops below 6.
Temperature affects the metabolic and growth rates of the organisms responsible for the biological pro-
cesses. Generally, as the temperature is raised 10-30°C, the growth rate increases. However, higher
temperature negatively affects the water solubility of oxygen and the oxygen transfer rate (solubility
decreases with a rise in temperature). For this reason, an increase of the aeration rate becomes neces-
sary during the hot season.
Nutrients. The nutritional balance of an aerobic system is primarily based upon satisfying the requirements
of the cell structure produced by the removal of BOD from waste. Efficient and successful biological oxi-
dation requires a minimal quantity of nitrogen and phosphorus. A BOD : N : P ratio of 100 : 5 : 1 in the
waste usually insures adequate nutrition. Tannery effluent is very rich in nitrogen and sometimes poor in
phosphorus.
33. 32 Secondary treatment
Figure 29. Surface (floating) aerators
Sludge volume index (SVI) is the volume occupied by 1 g of activated sludge after settling the aerated
mixed liquor in a 1,000 ml graduated cylinder or Imhoff cone for 30 minutes. It provides a good indi-
cation of sludge compacting characteristics, very helpful in controlling the activated sludge process,
especially in determining return sludge pumping requirements to maintain different mixed-liquor
concentrations.
Well settleable and mineralized sludges have SVI <100.
2.4 Aeration devices
Water (effluent) aeration is important business that employs a wide range of equipment. In addition
to cost, reliability, etc., the key criterion is the amount of air (oxygen) transfer per kW installed. Here
is one – rather arbitrary – classification:
a. Surface aerators
Radial flow, low speed, 20-60 rpm
Axial flow, high speed, 300-1200 rpm
Brush rotor (oxidation ditch)
b. Submerged turbines
c. Diffusers
Bubblers – porous and non-porous diffusers
Tubular
Jets (developed from Venturi ejectors)
34. Figure 30. Cross section of floating aerator
Photo 8. Surface aerators
Figure 31. Forced-air, submersed turbine aerator
Introduction to treatment of tannery effluents 33
35. 34 Secondary treatment
Photo 10. Fine-bubble difusers, dome and tubular type
Photo 9. Bottom air diffuser grid with one section and fine-bubble dome diffuser
2.5 Aeration basins, oxidation ditch
The possibly best biological treatment of tannery effluents is the oxidation ditch (OD) and its various
derivatives – a circular aeration basin (racetrack-shaped), with rotary-brush or vertical-rotor (carrousel)
aerators that extend across the width of the ditch.
36. Introduction to treatment of tannery effluents 35
Photo 11. Submersed turbine aerators in oxidation ditch
Figure 32. Schematic diagram of oxidation ditches with BOD removal, nitrification and denitrification
In addition to its simple construction and easy maintenance, the main advantage of the OD is its resilience
to variations in flow, pollution load, including shock loads. It is even possible to combine several ovals
and maintain different aeration regimes suitable for nitrification and denitrification.
37. 36 Secondary treatment
Photo 12. Oxidation ditch in operation
2.6 Secondary sedimentators
Their design is very similar to those of primary sedimentators, but the operational conditions are dif-
ferent. Also, the (excess – wastage) sludge evacuated at the tank bottom is normally bulkier and more
difficult to dewater.
Surface hydraulic loading – or surface overflow rate (SOR) – is the vertical velocity of the influent in
the secondary sedimentation tank (m3/m2 of tank surface per hour, m/h).
SOR of approximately 0.5 m3/m2 per hour is generally used for secondary sedimentation of tannery
effluents, i.e., less than for primary clarifiers.
Surface solid rate (SSR) is the quantity per hour of MLSS (kg) crossing the surface area of the secondary
sedimentation tank (kg/m2 of tank surface per hour) (see primary sedimentation).
SSR values between 2.0 and 3.0 kg/m2 per hour are generally used for secondary sedimentation of tan-
nery effluents.
The overflow from the secondary clarifiers represents the fully treated effluent usually fit for discharge
into a final recipient.
In order to satisfy the legal limits for nitrogen (ammonia and TKN), very often nitrification and denitri-
fication stages need to be introduced into the biological system. Nitrification requires extensive aera-
tion as well as a low F : M ratio (< 0,1) to facilitate conversion of nitrogen containing organic matter
into nitrate and nitrite salts. During the denitrification stage, which for operational reasons can take
place either at the very beginning or at the end of the biological treatment, these salts are converted
under anoxic conditions into neutral nitrogen gas (N2) and water.
38. Introduction to treatment of tannery effluents 37
Table 5. Characteristics of sludge dewatering equipment
2.7 Anaerobic biological treatment
As mentioned earlier, despite its high performance, comparatively lower costs and wide use in other
industries, anaerobic treatment has failed to make inroads in the tanning industry. The main reason is
that tannery effluent treatment leads to the development of a highly toxic, corrosive and flammable
gas, hydrogen sulphide (H2S); difficulties and risks in dealing with this gas prevail over other, positive
features of anaerobic treatment.
In certain cases, despite extensive physical-chemical and biological treatment in a well designed ETP, the
quality of the final effluent does not meet the promulgated discharge limits. The usual culprit is the
recalcitrant COD, i.e., compounds that the micro-organisms present in the floc are unable to decompose.
In such cases, it is necessary to resort to additional, usually more sophisticated and rather expensive
treatments such as mineralization of organic compounds by oxidation with H2O2 in the presence of
ferrous sulphate (Fenton process and its derivatives). Ozonation is sometimes included not so much to
kill potentially harmful micro-organisms but to destroy part of the residual COD.
4.1 Mechanical sludge dewatering
The main purpose of sludge dewatering is not only to reduce the volume and weight of material to be
transported but also to attain the dry matter content required for disposal at landfills.
The equipment used for this purpose – recessed-plate filters, belt presses and decanter centrifuges –
was already described earlier. Here is a short comparative overview of the main characteristics and
efficiencies of the various systems as well as changes in DS content throughout the treatment process.
(1) Polyelectrolyte (usually cationic): 2-4 g/kg of DS.
(2) Sludge conditioning with inorganic chemicals (iron salts and lime) is not strictly necessary,
but recommendable for enhancing filtration rate and general performance.
(3) About 10 m3/h of clean water at 4 bars per meter of belt width are required for continuous belt washing.
(4) Periodical cleaning of filtering cloth is required (at least once per week).
3. Advanced (tertiary) treatment
4. Sludge handling
39. 38 Sludge handling
Table 6. Dry matter content in sludge depending on process stage
and/or type of dewatering equipment
Photo 13. Containers for solid waste
4.2 Utilization and disposal
In comparison with sanitary sludges, tannery sludge has greater inorganic matter content, greater heavy
metal content, especially chromium and greater sulfur compound content. However, the main stumbling
block is the chromium content, with legislation and practice varying a lot from country to country.
A number of solutions for utilization and/or safe disposal of tannery sludge have been proposed, practiced,
tested, and applied at pilot and industrial scale: landfill, land application, composting, anaerobic digestion,
thermal treatment, vitrification, pyrolisys, brick making, etc., none of them proving satisfactory enough.
There is certainly no universal solution for sludge utilization/application. Each ETP produces sludge of
specific characteristics and different regions and countries have quite different regulations regarding
sludge utilization. Therefore, prior to any ETP construction, a detailed assessment of options should be
prepared and the most suitable application proposed.
In any case, handling, storage and transport of sludge and solid wastes from PTPs and ETPs should also
be safe and not contaminate the surroundings; thus, for example, the collection points should be pro-
tected against bad weather (rain, for example).
* Average values for mixed (primary + secondary) tannery sludges
40. Introduction to treatment of tannery effluents 39
Odours associated with wastewater are difficult to quantify because they are caused by a wide variety of
compounds and they are a nuisance that is more qualitative than quantitative – sensitive persons easily
detect very low concentrations of odoriferous substances in the air (sulphides/other sulphur compounds,
ammonia, amines, etc.). Local geographic and climatic conditions such as wind direction, land shape, air
humidity, ground and air temperature, etc. play an important role. Along the treatment line, the main
sources of bad smell are:
• equalization and sulphide oxidation;
• sludge thickening;
• biological aeration;
• in-plant storage of dewatered sludge;
• (temporary) sludge disposal site.
Yet, the main source of bad smell remains the stripping of hydrogen sulphide; it is not the concentra-
tion of sulphide per se, but the lowering of pH: the not disassociated H2S is present only at pH below
10. Thus, it is crucial to control pH and, if needed, alkalis like NaOH or lime are added to achieve pH
> 9.5-10. More extensive, uninterrupted aeration may help, but sometimes rigorous (and expensive)
methods such as adding hydrogen peroxide or pure oxygen are necessary. Nowadays, in some places,
nearly the entire ETP is covered and the air is purified.
5. The issue of bad odour
42. Introduction to treatment of tannery effluents 41
Figure34.Simplifiedflowchartofafull-fledgedtanneryeffluenttreatmentplant
43. 42 Monitoring, costs, OSH, management
Figure 35. Structure of average treatment costs at selected CETPs in India in 2005
Figure 36. Distribution of average total costs at selected CETPs in Italy
The extent of monitoring activities largely depends on local legal requirements and ETP size and it
includes a wide range of parameters: effluent volume(s), peak loads, pollution loads, chemical dosing,
dissolved oxygen (DO), sludge volume index (SVI), etc.
The costs of treatment vary a lot, depending on the local costs of:
• power;
• chemicals;
• financing;
• labour;
• sludge utilization and disposal options, etc.
In developing countries, the largest component is power, while sludge handling and disposal costs are com-
paratively low. If the reverse osmosis (RO) stage for desalination is installed, the cost of energy escalates further.
In industrialized countries, the largest cost component is dewatering and safe disposal of solids (sludge).
6. Monitoring, costs, OSH, management
44. Introduction to treatment of tannery effluents 43
Figure 38. Schematic chart of typical effluent treatment setup in industrialized countries
Figure 37. Schematic chart of typical effluent treatment setup for clusters in developing countries
While working out the costs of an ETP at an individual tannery is quite straightforward, different
methods are applied to compute the distribution of CETP operation costs among individual tanneries.
The key parameters used are typically the following:
• water consumption, m3/day;
• production capacity, tonnes of wet-salted hides/day;
• actual pollution load in terms of COD, suspended solids, sulphides and Cr;
• production output, m2/day of wet blue, crust or finished leather.
In developing countries, cost calculation methods for CETPs are usually very simple, being based solely
on effluent volume and type of tanning, whereas in Italy, for example, these methods are very sophisticated
and are based on many factors measured on-/off-line or estimated.
45. 44 Monitoring, costs, OSH, management
Table 7. Poisoning effects of hydrogen sulphide gas (H2S)
When it comes to occupational safety and health at work (OSH) in (C)ETPs, the main focus is on hydrogen
sulphide gas. As mentioned earlier, hydrogen sulphide is an extremely toxic and irritating gas. It has a
strong odour of rotten eggs but, paradoxically, it is perceived only at lower concentrations. This
explains the numerous accidents despite its known toxicity.
New toxicological data have led authorities in some countries to start reducing the recommended chronic-
exposure limits to hydrogen sulphide – the 8-hour time-weighted average of the threshold limit value (TLV-
TWA8) for H2S came down from 10 ppm to 1 ppm, and the short-term exposure limit (TLV-STEL) from 15
ppm to 5 ppm; as a result, even confirming compliance with the new standards will be a challenge.
Instruments used to detect and monitor H2S exposure can be either fixed or portable, whereas personal
detectors are worn by employees and typically sound an alarm at levels between 10 ppm and 15 ppm.
Due to this nearly permanent life threatening hazard, H2S meters are always positioned at critical points
and/or carried by staff. Also, certain activities such as entering pits can be carried out only in the presence
of skilled supervisors (the worker performing such an operation must also wear a safety harness).
Otherwise, general and specific measures concerning equipment and chemicals also apply to ETPs.
Nowadays it is taken for granted that in a well managed tannery there is a person of appropriate competence
and at an appropriate level of seniority who deals exclusively with increasingly complex environmental
issues, especially those related to effluent treatment; in some countries, this is a legal requirement.
ppm = parts per million
47. 46 Conclusions
The treatment of tannery effluents is by now a well established technology, and modular common effluent
treatment plants servicing traditional tannery clusters or newly created leather industry zones is a widely
accepted approach. However, two issues still pose serious challenges:
• High TDS (salinity) content, unaffected by treatment. This problem is especially pronounced in
developing countries where mixing tannery effluent with domestic sewage or its discharge into the
sea is not feasible, and the raw hides and skins are still preserved by salting. Relocation of tanneries
to the seaside is often not feasible, and desalination of treated effluent by reverse osmosis is very
expensive.
• Utilization or safe disposal of sludge.
Cost-effective solutions to both of these problems are still eagerly awaited.
7. Conclusions
51. 50 Annexes
Annex 4. A model of rotary screening drum
Annex 5. Types of sedimentation tanks
52. Introduction to treatment of tannery effluents 51
Annex 7. Sludge production in leather processing
Annex 6. Photos and cross section of a circular sedimentation tank
54. Introduction to treatment of tannery effluents 53
Annex 10. Personal hydrogen-gas monitor
Annex 9. Scheme of the membrane bioreactor (MBR)
Note: This is one of many brands in the market.
55. 54 Annexes
Annex 11. Reverse osmosis (RO): principle, diagram, photo of a small RO unit
56. Introduction to treatment of tannery effluents 55
Annex 12. Schematic view of constructed wetland – reed beds
58. Annex 14. Typical fluxogram of an ETP
Introduction to treatment of tannery effluents 57
It can be approximated that:
The volume of raw effluent = influent to biological treatment = volume of treated effluent.
59. 58 Annexes
Annex 15. A dialogue between a tanner and an environmental engineer
Information to be provided by the tanner:
• Production: daily input and types of raw material (hides, skins; fresh/wet-salted), processing stage
(wet blue, crust, finished), working days (per week/year, any closure periods), number of employees.
• Process – present, plans for the future: biocides used, hair-save unhairing, deliming on low dose of
ammonium salts, any degreasing, chrome management (direct recycling, high exhaustion, recovery).
• Effluent emissions:
– industrial (beamhouse, tanyard, general), segregation, total/peak/average flow, discharge
distribution over the day;
– rainwater – separate drainage, not mixed with industrial effluent;
– sanitary effluents – separate drainage, not mixed with industrial effluent.
• Raw effluent quality – detailed laboratory analysis of each of the three industrial streams
and/or combined effluent: BOD5, COD, SS, Cr, TKN, NH3-N, chlorides, sulphates (TDS).
• Nature of the recipient of treated effluent: sewage, open water body (river, lake).
• Officially (locally) prescribed quality of treated effluent – discharge limits.
• Area available for the ETP.
• Distance to residential areas.
• Any local solution for utilization and/or disposal of (chrome-containing) sludge.
Information about the local climate (temperatures, precipitations, wind directions), unit cost of electricity
and chemicals, primarily polyelectrolytes, as well as labour costs should also be required if necessary.
Questions a tanner should ask:
In addition to obvious questions concerning investment and operation costs, the tanner should specifically
focus the discussion on:
• A detailed explanation regarding the logic of the overall technical concept.
• A comparative evaluation of technical alternatives, e.g., bottom diffusers vs. Venturi ejectors for aera-
tion, conventional tank vs. oxidation ditch for biology, frame-filter press vs. decanter centrifuge, etc.
• The rate of purification for each treatment stage.
• Emergency procedures – back-up arrangements in case of the failure of parts or larger components
of the treatment system (e.g., collapse of the biological treatment).
• Occupational safety and health measures, including personal protection equipment (PPE).
• A concise overview of on- and off-line monitoring and control parameters, including the expected
value ranges at critical points (presence of H2S, COD, DO, settleability, DS content, etc.).
• Performance guarantee – warranty concerning the quality of the treated effluent in conformity with
local legislation (discharge limits).
• “If scenarios“ – provisions/buffers/safety margins/retrofitting/upgrades in case of failure to meet
(additional) norms.
60. Introduction to treatment of tannery effluents 59
Annex 16. Basic plant monitoring and control
Local legal requirements are crucial in determining the extent and frequency of tests conducted to
monitor and control ETP performance to satisfy discharge limits. Obviously, for that purpose, full laboratory
tests in accordance with (international) standardized procedures are required. However, regular monitoring
of key parameters is also important for optimizing the treatment process and reducing operation costs.
It is also assumed that recording of some parameters like effluent volumes is automated and that H2S
meters are always positioned at critical points and/or carried by staff in accordance with Occupational
Safety and Health (OSH) norms and procedures.
61. 60 Annexes
Annex 17. Discharge limits for treated tannery effluents in France, Italy and India
Note: The data in the table above refer to the year 2002.
* Special limits permitted by the regional authorities to certain CETPs located close to the sea
or if the effluent is mixed with sanitary wastewater:
- at Santa Croce, CuoioDepur and Fuccechino – chlorides: 5,000 mg/l; sulphates: 1,800 mg/l;
- at Arzignano – chlorides: 900 mg/l; sulphates: 1,800 mg/l;
- at Solofra – chlorides: 3,500 mg/l; sulphates: 1,500 mg/l.
** In Tamil Nadu, India – TDS limit: 2,100 mg/l; chlorides: 1,000 mg/l; sulphates: 1,000 mg/l, for discharge
in surface water and sewer. Previously, up to 7,500 mg/l TDS were tolerated by the authorities.
*** In France, no discharge limits pertaining to chlorides, sulphates and TDS have been prescribed
except in special cases. (The authorities do not insist on norms relating to COD and nitrogen, if the effluent
is treated alongside with domestic sewage in a combined treatment plant. This relates exclusively
to effluent discharged in a sewer).
1As phenolic compounds (as C6 H5 OH).
62. Introduction to treatment of tannery effluents 61
Annex 18. Typical tannery ETP auxiliary chemicals and their dosing*
* Always in solution.
63. 62 Annexes
Annex 19. Environmental effects of the main constituents of tannery effluents
Solids
1. Suspended solids
Suspended solids present in effluents are defined as the quantity of insoluble matter contained in the
wastewater. These insoluble materials cause a variety of problems when discharged; essentially, there are
two types of solids distinguished by significantly different characteristics.
a. Solids with a rapid settling rate (settleable solids)
If wastewaters are to be treated in sewage works or to undergo traditional effluent treatment, the main
problems that arise are due to the large volume of sludge that forms as the solids settle. Sludge often
contains up to 97% water, giving rise to huge quantities of “light” sludge. Even viscous sludge has a
water content of about 93% and can easily block sumps, sludge pumps and pipes. All this sludge has
to be removed, transported, dewatered, dried and deposited, thus placing an inordinate strain on plant,
equipment and resources.
Even a thin layer of settled sludge can become a blanket that deprives sections of the river or lake bed of
oxygen. As a result, aquatic life dies and decomposition sets in.
b. Semi-colloidal solids
Semi-colloidal solids are very fine solids that, for all practical purposes, will not settle out even if the
effluent is left to stand for a considerable period of time. Semi-colloidal solids will not directly cause a
sludge problem. They can be broken down over an extended period by bacterial digestion and produce
solids, which will eventually settle.
2. Gross solids
Gross solids are larger than those a sampling machine can handle; hence they are not measured. Their
presence, however, is clear to see and the dangers they pose are fully recognized. The waste components
that give rise to this problem are often large pieces of leather cuttings, trimmings and gross shavings, fleshing
residues, solid hair debris and remnants of paper bags. They can be easily removed by means of coarse
bar screens set in the wastewater flow. However, if they emerge from the factory, they settle out very rapidly.
Major problems can develop if these materials settle in the pipes since they lead to blockages. The
problems can be very serious when blockages occur in inaccessible piping. The cost of replacing burned-out
motors or broken rotors is high. If discharged into gullies, ditches or water courses, the debris rapidly
accumulates causing blockages and leading to stagnation.
Oxygen demand
Many effluent components are broken down by bacterial action into simpler components. Oxygen is
required for both the survival of these (aerobic) bacteria and the breakdown of the components.
Depending on effluent composition, this breakdown can be quite rapid or may take a very long time.
If effluent with a high oxygen demand is discharged directly into surface water, the sensitive balance
64. Introduction to treatment of tannery effluents 63
maintained in the water becomes overloaded. Oxygen is stripped from the water causing oxygen-
dependent plants, bacteria, fish – as well as the river or stream itself – to die.
The outcome is an environment populated by anaerobic bacteria (which are not oxygen-dependent) leading
to toxic water conditions. A healthy river can tolerate substances with low levels of oxygen demand. The load
created by tanneries, however, is often excessive, and the effluent requires treatment prior to discharge. In
order to assess the impact of effluent discharge on surface waters or determine the cost of treatment, oxygen
demand needs to be determined. This can be done in two different ways:
1. Biochemical oxygen demand (BOD5)
The BOD5 analysis, generally called BOD, is widely used to assess the environmental demands of waste-
water. It should also be noted that, while BOD is a measure of the oxygen requirements of bacteria under
controlled conditions, many effluent components take longer than the period of analysis to break down.
Some chemicals will only be partially broken down, while others may not be significantly affected. Typically,
vegetable tanning wastes have a long breakdown period, often quoted as being up to 20 days. These longer
digestion periods can apply to a variety of chemicals used in manufacturing leather, including certain re-tan-
ning agents, some synthetic fat liquors, dyes, and residual proteins from hair solubilization.
This longer breakdown period means that the environmental impact is spread over a larger area as waste-
water components are carried over greater distances before breaking down.
2. Chemical oxygen demand (COD)
This method measures the oxygen required to oxidize the effluent sample entirely. It sets a value for the
materials that would normally be digested in the BOD5 analysis, the longer-term biodegradable products, as
well as the chemicals that remain unaffected by bacterial activity.
The semi-colloidal material in suspended solids is also included in the BOD and COD determinations.
Normally 1 mg/l of suspended solids will generate a COD increase of approximately 1.5 mg/l.
Nitrogen
Nitrogen is contained in several tannery effluent components. Sometimes, these sources have to be dif-
ferentiated.
Total Kjeldahl nitrogen (TKN)
Several tannery effluent components contain nitrogen as part of their chemical structure. The most common
chemicals are ammonia (from deliming materials) and the nitrogen contained in proteinaceous materials
(from liming/unhairing operations).
These sources of nitrogen pose two direct problems:
a. Plants require nitrogen in order to grow, but the high levels released by substances containing nitrogen
over-stimulate growth. Water-based plants and algae grow too rapidly, whereupon waterways become
clogged and their flow is impaired. As the plants die, a disproportionately high amount of organic matter has
to be broken down. If the load outstrips the natural supply of oxygen from the river, plants, fish and aerobic
bacteria die and ultimately anaerobic conditions develop.
65. 64 Annexes
b. The nitrogen released through protein breakdown and the deliming process is in the form of ammonia.
Bacteria can convert the latter over several stages into water and nitrogen gas, which is ultimately released
into the atmosphere. Both of these breakdown products are non-toxic, yet large amounts of oxygen are
needed in the process. If oxygen demand is greater than the level supplied naturally by the body of water,
toxic anaerobic conditions can rapidly develop.
Combining intensive aerobic and anoxic biological treatment can break down the nitrogenous com-
pounds. The oxygen demand is very high, thus leading to correspondingly high operational and energy
costs. Calculations show that, with typical tannery effluent, some 40% of oxygen requirements are spent
on removing the nitrogen component.
Sulphides (S2-)
The sulphide content in tannery effluent results from the use of sodium sulphide and sodium hydrosulphide
and the breakdown of hair in the unhairing process. Sulphides pose many problems. Under alkaline
conditions, sulphides remain largely in solution. When the pH of the effluent drops below 9.5, hydrogen
sulphide evolves from the effluent: the lower the pH, the higher the rate of evolution. Characterized
by a smell of rotten eggs, a severe odour problem occurs.
In its toxicity, hydrogen sulphide is comparable to hydrogen cyanide; even a low level of exposure to the
gas induces headaches and nausea, as well as possible eye damage. At higher levels, death can rapidly set
in, and countless deaths attributable to the build-up of sulphide in sewage systems have been recorded.
Hydrogen sulphide gas is also soluble. When absorbed, weak acids can form and cause corrosion. This
weakens metal roofing, girders and building supports. In sewers, major problems can arise as metal fit-
tings, structural reinforcements and piping corrode.
If discharged into surface water, even low concentrations pose toxic hazards. Sulphides can be oxidized
into non-toxic compounds by certain bacteria in rivers; however, this creates oxygen demand that, if
excessive, can harm aquatic life.
Neutral salts
Two common types of salts are to be found in tannery effluent:
1. Sulphates (SO4)2-
Sulphates are a component of tannery effluent which emanates from the use of sulphuric acid or products
with a high (sodium) sulphate content. Many auxiliary chemicals contain sodium sulphate as a by-product
of their manufacture. For example, chrome tanning powders contain high levels of sodium sulphate, as do
many synthetic re-tanning agents.
Removing the sulphide component from effluent by aeration creates an additional source, since the
oxidation process produces a whole range of substances, including sodium sulphate. Sulphates can be
66. Introduction to treatment of tannery effluents 65
precipitated by calcium-containing compounds to form calcium sulphate that has a low level of solubility.
Problems arise with soluble sulphates, however, for two main reasons:
a. Sulphates cannot be removed completely from a solution by chemical means. Under certain biological
conditions, it is possible to remove sulphate from a solution and bind the sulphur into micro-organisms.
Generally, however, the sulphate either remains as sulphate or is broken down by anaerobic bacteria to
produce malodorous hydrogen sulphide. This process occurs very rapidly in effluent treatment plants,
sewage systems and water courses, if effluents remain static. This bacterial conversion to hydrogen sulphide
in sewage systems results in the corrosion of metal parts, and unless it is sulphate-resistant, concrete will
gradually erode.
b. If no breakdown occurs, there is the risk of increasing the total concentration of salts in surface waters
and groundwater.
2. Chlorides (Cl-)
Chloride is introduced into tannery effluents as sodium chloride usually on account of the large quantities
of common salt used in hide and skin preservation or the pickling process. Being highly soluble and stable, it
is not affected by effluent treatment and nature, thus remaining as a burden on the environment.
Considerable quantities of salt are produced by industry and levels can rapidly rise to the maximum level
acceptable for drinking water. Increased salt content in groundwater, especially in areas of high industrial
density, is now becoming a serious environmental hazard.
Chlorides inhibit the growth of plants, bacteria and fish in surface waters; high levels can lead to break-
downs in cell structure. If the water is used for irrigation purposes, surface salinity increases through
evaporation and crop yields fall. When flushed from the soil by rain, chlorides re-enter the eco-system and
may ultimately end up in the groundwater.
Oils and grease
In leather manufacture, natural oils and grease are released from within the skin structure. If fat liquor
exhaustion is poor, some fatty substances may be produced through inter-reaction when wastewaters mingle.
Floating grease and fatty particles agglomerate to form “mats,” which then bind other materials, thus
causing a potential blockage problem especially in effluent treatment systems. If the surface waters are
contaminated with grease or thin layers of oil, oxygen transfer from the atmosphere is reduced. If these
fatty substances emulgate, they create a very high oxygen demand on account of their bio-degradability.
pH value
Acceptable limits for the discharge of wastewaters into both surface waters and sewers vary, ranging from
pH 5.5 to pH 10.0. Although stricter limits are often set, greater tolerance is shown towards higher pH
values since carbon dioxide from the atmosphere or from biological processes in healthy surface water
systems tends to lower pH levels very effectively to neutral conditions. If the surface water pH shifts too
far either way from the pH range of 6.5-7.5, sensitive fish and plant life may be lost.
67. 66 Annexes
Municipal and common treatment plants prefer discharges to be more alkaline to reduce the corrosive
effect on concrete. Metals tend to remain insoluble and more inert, and hydrogen sulphide evolution is
minimized. When biological processes are included in the treatment, the pH is lowered to more neutral
conditions by carbon dioxide.
Chromium compounds
Metal compounds are not biodegradable. They can thus be regarded as long-term environmental features.
Since they can also have accumulative properties, they are the subject of close attention. Two forms of
chrome are associated with the tanning industry, and their properties are often confused.
1. Chrome 3+ (trivalent chrome, chrome III)
Chromium is mainly found in waste from the chrome tanning process; it occurs as part of the re-tanning
system and is displaced from leathers during re-tanning and dyeing processes. This chrome is discharged
in soluble form; however, when mixed with tannery wastewaters from other processes (especially if
proteins are present), the reaction is very rapid. Precipitates are formed, mainly protein-chrome, which
add to sludge generation.
Very fine colloids are also formed which are then stabilized by the chrome – in effect, the protein has been
partially tanned. The components are thus highly resistant to biological breakdown, and the biological
process in both surface waters and treatment plants is inhibited.
Once successfully broken down, chromium hydroxide precipitates and persists in the ecosystem for an
extended period of time. If chrome discharges are excessive, the chromium might remain in the solution.
Even in low concentrations, it has a toxic effect upon daphnia, thus disrupting the food chain for fish life
and possibly inhibiting photosynthesis.
2. Chrome 6+ (hexavalent chrome, chrome VI)
Dichromates are toxic to fish life since they swiftly penetrate cell walls. They are mainly absorbed
through the gills and the effect is accumulative. However, tannery effluents are unlikely to contain
chromium in this form.
68. Future Trends in the Leather and Leather Products Industry and Trade 67
Annex 20. References
1. Mass balance in leather processing, J. Buljan, J. Ludvik, G. Reich, IULTCS Congress, 1997.
2. Pollutants in tannery effluents: Definitions and environmental impact, limits for discharge into water
bodies and sewers, M. Bosnic, J. Buljan, R.P. Daniels.
3. Selection of equipment for laboratories monitoring pollution in the tanning industry, M. Aloy,
(English, French, Spanish, Chinese).
4. Safety handbook: How to deal with hydrogen sulphide gas in tanneries and effluent treatment
plants, J. Hannak, G. Jayaraj.
5. Tanneries and the environment: A technical guide, UNEP-UNIDO, 1991.
6. Occupational safety and health aspects of leather manufacture (OSH manual), J. Hannak, J. Buljan,
A. Sahasranaman & CTC.
7. Manual on landfill for tannery sludge, V. Post, R. Swaminathan, M. Aloy, T. Poncet.
8. Some considerations about the problem of salinity of tannery effluents, J. Buljan, LGR, Germany,
March 2004.
9. Costs of tannery waste treatment, J. Buljan, UNIDO Leather Industry Panel meeting, León, Mexico,
September 2005.
10. Benchmarking in the tanning industry, J. Buljan, UNIDO Leather Industry Panel meeting, Gramado,
Rio Grande do Sul, Brazil, May 2007.
11. Ökologische Probleme der Lederindustrie, Lieselotte Feikes, Bibliothek des Leders, Band 8, 2. Auflage,
1990.
12. http://www.fao.org/docrep/t0551e/t0551e05.htm
13. http://www.waterspecialists.biz/html/about_coagulation_flocculati.html
http://www.unep.or.jp/ietc/publications/freshwater/sb_summary/10.asp
69. Printed in Austria
UUNNIITTEEDD NNAATTIIOONNSS IINNDDUUSSTTRRIIAALL DDEEVVEELLOOPPMMEENNTT OORRGGAANNIIZZAATTIIOONN
Vienna International Centre, P.O. Box 300, 1400 Vienna, Austria.
Telephone: (+43-1) 26026-0. Fax: (+43-1) 26926-69.
E-mail: unido@unido.org Internet: http://www.unido.org