This paper presents the design of an automated braking system for electric bikes traveling uphill. The system uses a MEMS sensor to measure the bike's slope and acceleration. This data is sent to a microcontroller which controls the motor speed based on the sensor readings. When the bike reaches a certain inclination or acceleration threshold while traveling uphill, the system applies the brakes by reducing motor speed to prevent skidding and potential accidents. The system was prototyped using off-the-shelf hardware components and its effectiveness in regulating bike speed during uphill travel was demonstrated.
SPEED SYNCHRONIZATION OF MASTER –SLAVE D.C. MOTORS USING MICROCONTROLLER, FOR...Editor IJMTER
In textile industry many processes require speed synchronization of more than one motors involved in the process. Rolling of cloth should be synchronized with the speed of weaving spindle to avoid damage and motor speed synchronization is vital in conveyor belt driven by multiple motors. Abrupt load variations may cause hunting or oscillatory behavior in d. c. machines. This behavior can be detrimental to the process. The digitally controlled d. c. machines can have much aggravated phenomenon owing to poor sampling period selection. Traditionally processes are synchronized through mechanical transmission system consisting of a line shaft gears, pullers etc. Among the available software mechanisms master-slave synchronization is a widely used technique. Multi-motor applications have become very attractive field in industrial applications replacing in traditional mechanical coupling. Many textile applications involved synchronized speed motors. For example wrapping of clothes should be synchronized with the speed of weaving spindle to avoid damage and Similarly in some cases the speed of long conveyor belt driven by multiple motors is need to be constant. In such types of applications master slave technique is used as a software mechanism to synchronize the speed of different motors to avoid damage.
Speed Synchronization of Multiple Bldcmotors In Textile &Paper Mills Using Mi...IJERA Editor
Multiple motor setup has vast application in industries. The application can be in textile mills, paper mills and robotics. In these all application the synchronization is must between the motors to perform certain task. Speed synchronization is very essential in these all operation to avoid damage to the product. The synchronization is done by using microcontroller chip which controls the master slave whose speed is followed by the other motors which all have to be synchronized.
Speed Control of Induction Motor Using PLC and SCADA SystemIJERA Editor
Automation or automatic control is the use of various control systems for operating equipment such as
machinery, processes in factories, boilers and heat-treating ovens, switching in telephone networks, steering and
stabilization of ships, aircraft and other applications with minimal or reduced human intervention. Some
processes have been completely automated. The motor speed is controlled via the driver as an open loop control.
To make a more precise closed loop control of motor speed we will use a tachometer to measure the speed and
feed it back to the PLC, which compares to the desired value and take a control action, then the signal is
transferred to the motor – via driver – to increase / decrease the speed. We will measure the speed of the motor
using an incremental rotary encoder by adjusting parameters (PLC, driver) and also we need to reduce the
overall cost of the system. Our control system will be held using the available Siemens PLC. In addition, we will
monitor motor parameters via SCADA system.
The batteries used in electric and hybrid vehicles
consists of several cells with voltages between 3.6V battery and
4.2 V in series or parallel combinations of configurations for
obtaining the necessary available voltages in the operation of a
hybrid electric vehicle. How malfunction of a single cell affects
the behavior of the entire battery pack, BMS main function is to
protect individual cells against over-discharge, overload or
overheating. This is done by correct balancing of the cells. In
addition BMS estimates the battery charge status
SATELLITE DISH POSITIONING CONTROL BY DC MOTOR USING IR REMOTE CONTROL IAEME Publication
In this paper, PIC microcontroller was designed to develop a satellite dish positioning system which can be operated by using a remote control. The main point of using a dish is to receive signal from satellites and other broadcasting sources. In order to get the exact angle of position of the dish, it needs to be adjusted manually. In order to overcome the difficulty of adjusting manually, this paper helps in adjusting the position of the dish through a remote control. Remote control acts as a transmitter whose data is received by an IR receiver which is interfaced to a microcontroller of PIC 16F877A. The remote control sends coded data to the receiver whose output is then sent to the microcontroller.
SPEED SYNCHRONIZATION OF MASTER –SLAVE D.C. MOTORS USING MICROCONTROLLER, FOR...Editor IJMTER
In textile industry many processes require speed synchronization of more than one motors involved in the process. Rolling of cloth should be synchronized with the speed of weaving spindle to avoid damage and motor speed synchronization is vital in conveyor belt driven by multiple motors. Abrupt load variations may cause hunting or oscillatory behavior in d. c. machines. This behavior can be detrimental to the process. The digitally controlled d. c. machines can have much aggravated phenomenon owing to poor sampling period selection. Traditionally processes are synchronized through mechanical transmission system consisting of a line shaft gears, pullers etc. Among the available software mechanisms master-slave synchronization is a widely used technique. Multi-motor applications have become very attractive field in industrial applications replacing in traditional mechanical coupling. Many textile applications involved synchronized speed motors. For example wrapping of clothes should be synchronized with the speed of weaving spindle to avoid damage and Similarly in some cases the speed of long conveyor belt driven by multiple motors is need to be constant. In such types of applications master slave technique is used as a software mechanism to synchronize the speed of different motors to avoid damage.
Speed Synchronization of Multiple Bldcmotors In Textile &Paper Mills Using Mi...IJERA Editor
Multiple motor setup has vast application in industries. The application can be in textile mills, paper mills and robotics. In these all application the synchronization is must between the motors to perform certain task. Speed synchronization is very essential in these all operation to avoid damage to the product. The synchronization is done by using microcontroller chip which controls the master slave whose speed is followed by the other motors which all have to be synchronized.
Speed Control of Induction Motor Using PLC and SCADA SystemIJERA Editor
Automation or automatic control is the use of various control systems for operating equipment such as
machinery, processes in factories, boilers and heat-treating ovens, switching in telephone networks, steering and
stabilization of ships, aircraft and other applications with minimal or reduced human intervention. Some
processes have been completely automated. The motor speed is controlled via the driver as an open loop control.
To make a more precise closed loop control of motor speed we will use a tachometer to measure the speed and
feed it back to the PLC, which compares to the desired value and take a control action, then the signal is
transferred to the motor – via driver – to increase / decrease the speed. We will measure the speed of the motor
using an incremental rotary encoder by adjusting parameters (PLC, driver) and also we need to reduce the
overall cost of the system. Our control system will be held using the available Siemens PLC. In addition, we will
monitor motor parameters via SCADA system.
The batteries used in electric and hybrid vehicles
consists of several cells with voltages between 3.6V battery and
4.2 V in series or parallel combinations of configurations for
obtaining the necessary available voltages in the operation of a
hybrid electric vehicle. How malfunction of a single cell affects
the behavior of the entire battery pack, BMS main function is to
protect individual cells against over-discharge, overload or
overheating. This is done by correct balancing of the cells. In
addition BMS estimates the battery charge status
SATELLITE DISH POSITIONING CONTROL BY DC MOTOR USING IR REMOTE CONTROL IAEME Publication
In this paper, PIC microcontroller was designed to develop a satellite dish positioning system which can be operated by using a remote control. The main point of using a dish is to receive signal from satellites and other broadcasting sources. In order to get the exact angle of position of the dish, it needs to be adjusted manually. In order to overcome the difficulty of adjusting manually, this paper helps in adjusting the position of the dish through a remote control. Remote control acts as a transmitter whose data is received by an IR receiver which is interfaced to a microcontroller of PIC 16F877A. The remote control sends coded data to the receiver whose output is then sent to the microcontroller.
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology.
Analysis of Induction Motor Speed Control Using SCADA Based Drive Operated Sy...IJSRD
This Paper represents the analysis of induction motor speed control using VFD (Variable Frequency Drive) system operated by PLC-SCADA system. The main aim of the paper is to dealt with the concept of speed control of a three-phase induction motor with energy saving. To do so, a VFD (Variable Frequency Drive) is used for controlling the speed of a three-phase induction motor with variable load attached to the motor. It certainly leads to the best performance and high efficiency of the induction motor. Programmable Logic Controller (PLC) and Supervisory Control And Data Acquisition (SCADA) are two new systems to control a Variable Frequency Drive (VFD) whose output is given to a three-phase induction motor and driving a conveyor belt. The conveyor belt has three sensors are inputs which senses a passing object and carries out the necessary instructions programmed in ladder logic programming of the PLC through the computer (PC). The SCADA software installed in the PC in turn enables the human operator to control the entire operation away from the plant and just by using the virtual inputs designated on his computer screen.
Density based traffic signal control using microcontrollerkrity kumari
Description : This project includes controller ATmega 32A, Led (blue,red,yellow), IR sensor modules.
Specification : Power supply (12 v -1amp), frequency of controller Atmega 32A is 8 Mhz, range of IR
module is 1m and frequency of IR module is 32KHz.
Method of work : 1.Design of circuit
2. Programming in ICC AVR.
3. Simulation of design through Proteus.
Micro controller based Traffic control systemRohit Kumar
This project deals with traffic system controlled by a microcontroller.
using IR controllers instead of using old timing circuits.
This system aims to provide much better and safer way of controlling Traffic signal system.
This system of controlling will help a lot in future.
TRAFFIC SIGNAL CONTROL USING IR SENSORSKunal Kabra
The main objective of this project is to design an intelligent auto traffic signal control system.
Traffic congestion is one of the major issues to be considered. Generally Vehicular traffic
Intersects at the junctions of the road and are controlled by the traffic signals .Traffic signals
Need a good coordination and control to ensure the smooth and safe flow of the vehicular traffic.
During the rush hours, the traffic on the roads is at its peak. Also, there is a possibility for the
Emergency vehicles to stuck in the traffic jam. Therefore; there is a need for the dynamic control
of the traffic during rush hours. Hence I propose a smart traffic signal controller .The proposed
System tries to minimize the possibilities of traffic jams, caused by the traffic lights, to some
Extent by clearing the road with higher density of vehicles and also provides the clearance for the Emergency vehicle if any. The system is based on the AVR micro controller and IR sensors
Technology.
The main objective of this project is controlling speed of BLDC motors with the help of microcontroller. To make the industry automation the equipment and machineries should be controlled automatically. So control of the machineries which involving this motor can be done accurately. It displays its speed using an IR method of speed sensor mechanism.
Analysis and control of four quadrant operation of three phase brushless dc (...eSAT Publishing House
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology
This is density based traffic light control system using Programmable logic controller(PLC). Then side which have more vehicles(density) will be getting on first. This process will take place according to number of vehicles.
VEHICLE DENSITY CONTROLLED AUTOMATIC TRAFFIC LIGHT from KMP Engineering collegeHIGHVOLTEEE
ABSTRACT
The project is designed to develop a density based dynamic traffic signal
system. The signal timing changes automatically on sensing the traffic density
at the junction. Traffic congestion is a severe problem in many major cities
across the world and it has become a nightmare for the commuters in these
cities. Conventional traffic light system is based on fixed time concept allotted
to each side of the junction which cannot be varied as per varying traffic
density. Junction timings allotted are fixed. Sometimes higher traffic density at
one side of the junction demands longer green time as compared to standard
allotted time. The proposed system using a microcontroller of 8051 series duly
interfaced with sensors, changes the junction timing automatically to
accommodate movement of vehicles smoothly avoiding unnecessary waiting
time at the junction. The sensors used in this project are IR and photodiodes are
in line of sight configuration across the loads to detect the density at the traffic
signal. The density of the vehicles is measured in three zones i.e., low, medium,
high based on which timings are allotted accordingly. Further the project can
be enhanced by synchronizing all the traffic junctions in the city by establishing
a network among them. The network can be wired or wireless. This
synchronization will greatly help in reducing traffic congestion.
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology.
Analysis of Induction Motor Speed Control Using SCADA Based Drive Operated Sy...IJSRD
This Paper represents the analysis of induction motor speed control using VFD (Variable Frequency Drive) system operated by PLC-SCADA system. The main aim of the paper is to dealt with the concept of speed control of a three-phase induction motor with energy saving. To do so, a VFD (Variable Frequency Drive) is used for controlling the speed of a three-phase induction motor with variable load attached to the motor. It certainly leads to the best performance and high efficiency of the induction motor. Programmable Logic Controller (PLC) and Supervisory Control And Data Acquisition (SCADA) are two new systems to control a Variable Frequency Drive (VFD) whose output is given to a three-phase induction motor and driving a conveyor belt. The conveyor belt has three sensors are inputs which senses a passing object and carries out the necessary instructions programmed in ladder logic programming of the PLC through the computer (PC). The SCADA software installed in the PC in turn enables the human operator to control the entire operation away from the plant and just by using the virtual inputs designated on his computer screen.
Density based traffic signal control using microcontrollerkrity kumari
Description : This project includes controller ATmega 32A, Led (blue,red,yellow), IR sensor modules.
Specification : Power supply (12 v -1amp), frequency of controller Atmega 32A is 8 Mhz, range of IR
module is 1m and frequency of IR module is 32KHz.
Method of work : 1.Design of circuit
2. Programming in ICC AVR.
3. Simulation of design through Proteus.
Micro controller based Traffic control systemRohit Kumar
This project deals with traffic system controlled by a microcontroller.
using IR controllers instead of using old timing circuits.
This system aims to provide much better and safer way of controlling Traffic signal system.
This system of controlling will help a lot in future.
TRAFFIC SIGNAL CONTROL USING IR SENSORSKunal Kabra
The main objective of this project is to design an intelligent auto traffic signal control system.
Traffic congestion is one of the major issues to be considered. Generally Vehicular traffic
Intersects at the junctions of the road and are controlled by the traffic signals .Traffic signals
Need a good coordination and control to ensure the smooth and safe flow of the vehicular traffic.
During the rush hours, the traffic on the roads is at its peak. Also, there is a possibility for the
Emergency vehicles to stuck in the traffic jam. Therefore; there is a need for the dynamic control
of the traffic during rush hours. Hence I propose a smart traffic signal controller .The proposed
System tries to minimize the possibilities of traffic jams, caused by the traffic lights, to some
Extent by clearing the road with higher density of vehicles and also provides the clearance for the Emergency vehicle if any. The system is based on the AVR micro controller and IR sensors
Technology.
The main objective of this project is controlling speed of BLDC motors with the help of microcontroller. To make the industry automation the equipment and machineries should be controlled automatically. So control of the machineries which involving this motor can be done accurately. It displays its speed using an IR method of speed sensor mechanism.
Analysis and control of four quadrant operation of three phase brushless dc (...eSAT Publishing House
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology
This is density based traffic light control system using Programmable logic controller(PLC). Then side which have more vehicles(density) will be getting on first. This process will take place according to number of vehicles.
VEHICLE DENSITY CONTROLLED AUTOMATIC TRAFFIC LIGHT from KMP Engineering collegeHIGHVOLTEEE
ABSTRACT
The project is designed to develop a density based dynamic traffic signal
system. The signal timing changes automatically on sensing the traffic density
at the junction. Traffic congestion is a severe problem in many major cities
across the world and it has become a nightmare for the commuters in these
cities. Conventional traffic light system is based on fixed time concept allotted
to each side of the junction which cannot be varied as per varying traffic
density. Junction timings allotted are fixed. Sometimes higher traffic density at
one side of the junction demands longer green time as compared to standard
allotted time. The proposed system using a microcontroller of 8051 series duly
interfaced with sensors, changes the junction timing automatically to
accommodate movement of vehicles smoothly avoiding unnecessary waiting
time at the junction. The sensors used in this project are IR and photodiodes are
in line of sight configuration across the loads to detect the density at the traffic
signal. The density of the vehicles is measured in three zones i.e., low, medium,
high based on which timings are allotted accordingly. Further the project can
be enhanced by synchronizing all the traffic junctions in the city by establishing
a network among them. The network can be wired or wireless. This
synchronization will greatly help in reducing traffic congestion.
Mitsubishi ,
Catalog Thiết Bị Điện Mitsubishi , Catalog Thiết Bị Điện
Catalog Phụ Kiện Mitsubishi , Catalog Phụ Kiện,
Catalog Mitsubishi , Catalog,
https://www.dienhathe.com,
Chi tiết các sản phẩm khác của Mitsubishi tại https://dienhathe.com
Xem thêm các Catalog khác của Mitsubishi tại https://dienhathe.info
Để nhận báo giá sản phẩm Mitsubishi vui lòng gọi: 0907.764.966
IJERA (International journal of Engineering Research and Applications) is International online, ... peer reviewed journal. For more detail or submit your article, please visit www.ijera.com
Overview of the fundamental roles in Hydropower generation and the components involved in wider Electrical Engineering.
This paper presents the design and construction of hydroelectric dams from the hydrologist’s survey of the valley before construction, all aspects and involved disciplines, fluid dynamics, structural engineering, generation and mains frequency regulation to the very transmission of power through the network in the United Kingdom.
Author: Robbie Edward Sayers
Collaborators and co editors: Charlie Sims and Connor Healey.
(C) 2024 Robbie E. Sayers
Welcome to WIPAC Monthly the magazine brought to you by the LinkedIn Group Water Industry Process Automation & Control.
In this month's edition, along with this month's industry news to celebrate the 13 years since the group was created we have articles including
A case study of the used of Advanced Process Control at the Wastewater Treatment works at Lleida in Spain
A look back on an article on smart wastewater networks in order to see how the industry has measured up in the interim around the adoption of Digital Transformation in the Water Industry.
NO1 Uk best vashikaran specialist in delhi vashikaran baba near me online vas...Amil Baba Dawood bangali
Contact with Dawood Bhai Just call on +92322-6382012 and we'll help you. We'll solve all your problems within 12 to 24 hours and with 101% guarantee and with astrology systematic. If you want to take any personal or professional advice then also you can call us on +92322-6382012 , ONLINE LOVE PROBLEM & Other all types of Daily Life Problem's.Then CALL or WHATSAPP us on +92322-6382012 and Get all these problems solutions here by Amil Baba DAWOOD BANGALI
#vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore#blackmagicformarriage #aamilbaba #kalajadu #kalailam #taweez #wazifaexpert #jadumantar #vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore #blackmagicforlove #blackmagicformarriage #aamilbaba #kalajadu #kalailam #taweez #wazifaexpert #jadumantar #vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore #Amilbabainuk #amilbabainspain #amilbabaindubai #Amilbabainnorway #amilbabainkrachi #amilbabainlahore #amilbabaingujranwalan #amilbabainislamabad
Immunizing Image Classifiers Against Localized Adversary Attacksgerogepatton
This paper addresses the vulnerability of deep learning models, particularly convolutional neural networks
(CNN)s, to adversarial attacks and presents a proactive training technique designed to counter them. We
introduce a novel volumization algorithm, which transforms 2D images into 3D volumetric representations.
When combined with 3D convolution and deep curriculum learning optimization (CLO), itsignificantly improves
the immunity of models against localized universal attacks by up to 40%. We evaluate our proposed approach
using contemporary CNN architectures and the modified Canadian Institute for Advanced Research (CIFAR-10
and CIFAR-100) and ImageNet Large Scale Visual Recognition Challenge (ILSVRC12) datasets, showcasing
accuracy improvements over previous techniques. The results indicate that the combination of the volumetric
input and curriculum learning holds significant promise for mitigating adversarial attacks without necessitating
adversary training.
Industrial Training at Shahjalal Fertilizer Company Limited (SFCL)MdTanvirMahtab2
This presentation is about the working procedure of Shahjalal Fertilizer Company Limited (SFCL). A Govt. owned Company of Bangladesh Chemical Industries Corporation under Ministry of Industries.
Student information management system project report ii.pdfKamal Acharya
Our project explains about the student management. This project mainly explains the various actions related to student details. This project shows some ease in adding, editing and deleting the student details. It also provides a less time consuming process for viewing, adding, editing and deleting the marks of the students.
About
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.
Technical Specifications
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
Key Features
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface
• Compatible with MAFI CCR system
• Copatiable with IDM8000 CCR
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
Application
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.
Saudi Arabia stands as a titan in the global energy landscape, renowned for its abundant oil and gas resources. It's the largest exporter of petroleum and holds some of the world's most significant reserves. Let's delve into the top 10 oil and gas projects shaping Saudi Arabia's energy future in 2024.