This document provides instructions for an experiment to verify the superposition theorem in electrical circuits. The experiment involves measuring current through a resistor under three conditions: when two voltage sources are connected, when only the first voltage source is connected, and when only the second voltage source is connected. The readings are then used to check if the total current equals the sum of the individual currents, which would verify the superposition theorem. The document gives the circuit diagram, component values, procedure, observation table, and conclusion.

1. Maharashtra Institute of Technology,
Aurangabad
LABORATORY MANUAL
Practical Experiment Instruction Sheet
EXPERIMENT TITLE : Verification of Superposition Theorem.
EXPERIMENT NO.9 : MIT(T)/ETC/Basic Electrical Engineering /Manual No.1
FY(All) DEPARTMENT: Electronics & Telecommunication Engineering
LABORATORY : Basic Electrical Engineering Location Part I Page 41
Aim: Verification of Superposition Theorem.
Apparatus: 1.Trainer kit 2.Patch cord etc.
Theory:
In any linear bilateral network containing two or more sources (Voltage and current sources), the
current through any branch is the algebraic summation of all the currents in the branch, produced by
each source acting alone, when all other sources are replaced by their internal resistances. While
considering one voltage source, all other voltage sources should be short circuited and current sources
should be open circuited their internal resistance in the circuit. Similarly, voltage across any conductor
is the algebraic sum of the voltages, which each EMF would have produced singly.
Experiment set-up:
Fig. 2(a) V1 and V2 both connected
Prepared By: Mr. S.S. Chate Approved By: Dr. G.S. Sable

2. Maharashtra Institute of Technology,
Aurangabad
LABORATORY MANUAL
Practical Experiment Instruction Sheet
EXPERIMENT TITLE :Verification of Superposition Theorem.
EXPERIMENT NO.9 : MIT(T)/ETC/Basic Electrical Engineering /Manual No.1
FY(All) DEPARTMENT: Electronics & Telecommunication Engineering
LABORATORY : Basic Electrical Engineering Location Part I Page 42
Fig. 2(b) When V1 acting alone
Fig.-2(c) When V2 acting alone
Prepared By: Mr. S.S. Chate Approved By: Dr. G.S. Sable

3. Maharashtra Institute of Technology,
Aurangabad
LABORATORY MANUAL
Practical Experiment Instruction Sheet
EXPERIMENT TITLE :Verification of Superposition Theorem.
EXPERIMENT NO.9 : MIT(T)/ETC/Basic Electrical Engineering /Manual No.1
FY(All) DEPARTMENT: Electronics & Telecommunication Engineering
LABORATORY : Basic Electrical Engineering Location Part I Page 43
Component values: R1 = R2 = 390Ω, R3 = 680Ω, R4 = R5 = 100Ω.
Procedure:
1. Connect the main cord to 230v, 50Hz AC supply and switch on trainer kit.
2. Connect V1 to the voltmeter and adjust voltage to read e.g. 5V DC and similarly adjust V2 e.g. 5V
DC.
3. Do the connection as shown in fig. 2(a) by using patch cords.
4. Note the value of V1, V2 and current (I) through R3.
5. Do the connection as shown in fig. 2(b) only V1 connected (with same voltage as in steps (2) and
note the readings (I’).
6. Repeat the steps (5) when only V2 connected as shown in fig.2( c ) and same value of V2 as in steps
(2) Note the ammeter reading through R3 (I”).
7. Now verify the superposition theorem. I = I’ + I”
8. Repeat the experiment for different values of V1 and V2. Record reading in observation table 1.
Refer connection diagram fig.2 (a), (b) (c). Current meter between H and I.
Prepared By: Mr. S.S. Chate Approved By: Dr. G.S. Sable

4. Maharashtra Institute of Technology,
Aurangabad
LABORATORY MANUAL
Practical Experiment Instruction Sheet
EXPERIMENT TITLE :Verification of Superposition Theorem.
EXPERIMENT NO.9 : MIT(T)/ETC/Basic Electrical Engineering /Manual No.1
FY(All) DEPARTMENT: Electronics & Telecommunication Engineering
LABORATORY : Basic Electrical Engineering Location Part I Page 44
Connection diagram for second set:
Fig-3(a) Both V1 and V2 acting alone
Fig-3(b) When V2 acting alone
Prepared By: Mr. S.S. Chate Approved By: Dr. G.S. Sable

5. Maharashtra Institute of Technology,
Aurangabad
LABORATORY MANUAL
Practical Experiment Instruction Sheet
EXPERIMENT TITLE :Verification of Superposition Theorem.
EXPERIMENT NO.9 : MIT(T)/ETC/Basic Electrical Engineering /Manual No.1
FY(All) DEPARTMENT: Electronics & Telecommunication Engineering
LABORATORY : Basic Electrical Engineering Location Part I Page 45
Fig-3(c ) When V1 acting alone
Procedure:
1. Do the connection as in fig-3(a) adjust the voltages V1, V2 and note down the readings V1, V2 and I1.
2. Note the readings when V1 acting alone I’1
3. Note the value of I”1 when V2 acting.
4. Verify the superposition theorem. I1 = I’1 + I”1
5. Repeat the experiment for different values of V1 and V2. Record your readings in observation
table-2. Refer connection diagram fig-3(a), (b) and ( c ).
Prepared By: Mr. S.S. Chate Approved By: Dr. G.S. Sable

6. Maharashtra Institute of Technology,
Aurangabad
LABORATORY MANUAL
Practical Experiment Instruction Sheet
EXPERIMENT TITLE :Verification of Superposition Theorem.
EXPERIMENT NO.9 : MIT(T)/ETC/Basic Electrical Engineering /Manual No.1
FY(All) DEPARTMENT: Electronics & Telecommunication Engineering
LABORATORY : Basic Electrical Engineering Location Part I Page 46
Observation Table:
Sr.
No.
Observations Calculations
V1
Volts
V2
Volts
I (mA) V1 & V2
Connected
I’ (mA) With
V1 acting alone
I” (mA) With V2
acting alone
I = I’ + I”
(mA)
1
2
3
4
Conclusion: As I = I’ + I”, which verify the superposition theorem. The small difference is due to
meter error, observation error and due to neglecting the internal resistance.
Prepared By: Mr. S.S. Chate Approved By: Dr. G.S. Sable