This paper presents a current mode Pulse Width Modulation (PWM) controlled Flyback converter using UC3842 for Electrical Discharge Machining current generator control circuit. Circuit simplicity and high efficiency can be achieved by a Flyback converter with current mode PWM controller. The behaviors of the system's operation is analyzed and discussed by varying the load resistance. Matlab sofware is used to simulate the Flyback converter where a prototype has been built and tested to verify its performance.
Analysis of Multilevel Inverter using Bipolar and Unipolar Switching Schemes ...ijsrd.com
Cascaded H-bridge Multilevel Inverter (MLI) is most efficient topology for medium and high voltage DC-AC conversion, having less output harmonics and less commutation losses. Disadvantages are their complexity, more number of power devices, passive components and a complex control circuitry. Here a Cascaded Hybrid Multilevel Inverter is used to produce a three phase 9-level output voltages. Now a day inverter is also know as a DC-AC converter, is one of the most popular part of electrical device. This proposed inverter widely used in industries application such as speed control of induction motor. This thesis focus on three phase 9-level bipolar and unipolar switching inverter with characteristics like output voltage boosting ability and also we discus about the bipolar and unipolar switching scheme along with capacitor voltage control. The modified topology uses Cascaded H-bridge (CHB) with bidirectional and unidirectional switches producing boost up output voltage. Here a hybrid Pulse Width Modulation (PWM) technique is applied to control the power devices. This modulation technique uses a sine wave and a repeating wave, these waves are combined and a complete reference wave is generated. There is comparative study between CHB and modified topology between number of power devices used and Total Harmonic Distortions (THD). THD of modified topology is reduced and analyzed by FFT window. The results are observed by MATLAB/SIMULINK software.
This paper presents combinations of level shifted pulse-width modulation algorithm with conventional discontinuous pulse-width modulation methods for cascaded multilevel inverters. In the proposed DPWM a zero sequence signal is injected in sinusoidal reference signal to generate various modulators with easier implementation. The analysis four various control strategies namely Common Carrier (CC), Inverted Carrier (IC), Phase Shifted (PS) and Inverted Phase Shift (IPS) for cascaded multilevel inverter fed induction motor drive has been illustrated. To validate the proposed work experimental tests has been carried out using dSPACE controller. Experimental study proves that using proposed algorithms reduction in common-mode voltage with fewer harmonics along with reduced switching loss for a cascaded multilevel inverter fed motor drive has been achieved.
Fuzzy logic Control & Minimizing Commutation Torque Ripple for Brushless DC M...Editor IJMTER
Brushless dc motor still suffers from commutation torque ripple, which mainly depends
on speed and transient line current in the commutation interval. This paper presents a novel circuit
topology and a dc link voltage control strategy to keep incoming and outgoing phase currents
changing at the same rate during commutation. A dc–dc single-ended primary inductor converter
(SEPIC) and a switch selection circuit are employed in front of the inverter. The desired
commutation voltage is accomplished by the SEPIC converter. The dc link voltage control strategy is
carried out by the switch selection circuit to separate two procedures, adjusting the SEPIC converter
and regulating speed. The cause of commutation ripple is analyzed, and the way to obtain the desired
dc link voltage is introduced in detail. Finally, simulation and experimental results show that,
compared with the dc–dc converter, the proposed method can obtain the desired voltage much faster
and minimize commutation torque ripple more efficiently at both high and low speeds and the closed
loop control is achieved by Fuzzy logic control.
Analysis of Multilevel Inverter using Bipolar and Unipolar Switching Schemes ...ijsrd.com
Cascaded H-bridge Multilevel Inverter (MLI) is most efficient topology for medium and high voltage DC-AC conversion, having less output harmonics and less commutation losses. Disadvantages are their complexity, more number of power devices, passive components and a complex control circuitry. Here a Cascaded Hybrid Multilevel Inverter is used to produce a three phase 9-level output voltages. Now a day inverter is also know as a DC-AC converter, is one of the most popular part of electrical device. This proposed inverter widely used in industries application such as speed control of induction motor. This thesis focus on three phase 9-level bipolar and unipolar switching inverter with characteristics like output voltage boosting ability and also we discus about the bipolar and unipolar switching scheme along with capacitor voltage control. The modified topology uses Cascaded H-bridge (CHB) with bidirectional and unidirectional switches producing boost up output voltage. Here a hybrid Pulse Width Modulation (PWM) technique is applied to control the power devices. This modulation technique uses a sine wave and a repeating wave, these waves are combined and a complete reference wave is generated. There is comparative study between CHB and modified topology between number of power devices used and Total Harmonic Distortions (THD). THD of modified topology is reduced and analyzed by FFT window. The results are observed by MATLAB/SIMULINK software.
This paper presents combinations of level shifted pulse-width modulation algorithm with conventional discontinuous pulse-width modulation methods for cascaded multilevel inverters. In the proposed DPWM a zero sequence signal is injected in sinusoidal reference signal to generate various modulators with easier implementation. The analysis four various control strategies namely Common Carrier (CC), Inverted Carrier (IC), Phase Shifted (PS) and Inverted Phase Shift (IPS) for cascaded multilevel inverter fed induction motor drive has been illustrated. To validate the proposed work experimental tests has been carried out using dSPACE controller. Experimental study proves that using proposed algorithms reduction in common-mode voltage with fewer harmonics along with reduced switching loss for a cascaded multilevel inverter fed motor drive has been achieved.
Fuzzy logic Control & Minimizing Commutation Torque Ripple for Brushless DC M...Editor IJMTER
Brushless dc motor still suffers from commutation torque ripple, which mainly depends
on speed and transient line current in the commutation interval. This paper presents a novel circuit
topology and a dc link voltage control strategy to keep incoming and outgoing phase currents
changing at the same rate during commutation. A dc–dc single-ended primary inductor converter
(SEPIC) and a switch selection circuit are employed in front of the inverter. The desired
commutation voltage is accomplished by the SEPIC converter. The dc link voltage control strategy is
carried out by the switch selection circuit to separate two procedures, adjusting the SEPIC converter
and regulating speed. The cause of commutation ripple is analyzed, and the way to obtain the desired
dc link voltage is introduced in detail. Finally, simulation and experimental results show that,
compared with the dc–dc converter, the proposed method can obtain the desired voltage much faster
and minimize commutation torque ripple more efficiently at both high and low speeds and the closed
loop control is achieved by Fuzzy logic control.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
Implementation for Controller to Unified Single Phase Power Flow Using Digita...IJERA Editor
Presenting in his paper, Digital signal processor (DSP)-based implementation of a single phase unified power flow controller (UPFC). For shunt side and series side An efficient UPFC control algorithm is achieved. Discussing the laboratory experimental results using DC source are taken as an UPFC linked by two ll-bridge PWM voltage source converters.
Direct Torque Control of Induction Motor Drive Fed from a Photovoltaic Multil...IJERA Editor
This paper presents Direct Torque Control (DTC) using Space Vector Modulation (SVM) for an induction motor drive fed from a photovoltaic multilevel inverter (PV-MLI). The system consists of two main parts PV DC power supply (PVDC) and MLI. The PVDC is used to generate DC isolated sources with certain ratios suitable for the adopted MLI. Beside the hardware system, the control system which uses the torque and speed estimation to control the load angle and to obtain the appropriate flux vector trajectory from which the voltage vector is directly derived based on direct torque control methods. The voltage vector is then generated by a hybrid multilevel inverter by employing space vector modulation (SVM). The inverter high quality output voltage which leads to a high quality IM performances. Besides, the MLI switching losses is very low due to most of the power cell switches are operating at nearly fundamental frequency. Some selected simulation results are presented for system validation.
International Journal of Engineering Research and DevelopmentIJERD Editor
Electrical, Electronics and Computer Engineering,
Information Engineering and Technology,
Mechanical, Industrial and Manufacturing Engineering,
Automation and Mechatronics Engineering,
Material and Chemical Engineering,
Civil and Architecture Engineering,
Biotechnology and Bio Engineering,
Environmental Engineering,
Petroleum and Mining Engineering,
Marine and Agriculture engineering,
Aerospace Engineering.
Unified Power Quality Conditioner Model Based with Series and Shunt FiltersIAES-IJPEDS
With the increase of the complexion in the power distribution system, it is very possible that several kinds of power quality disturbances are happened in a power distribution system simultaneously.This paper proposes a unified power quality conditioner (UPQC) including a series and a shunt active power filter (APF) to compensate harmonics in both the distorted supply voltage and nonlinear load current. In the series APF control scheme, a proportional-integral (PI) controller, meanwhile a PI controller and are designed in the shunt APF control scheme to relieve harmonic currents produced by nonlinear loads. The DC voltage is maintained constant using Two degree of freedom proportional integral voltage controller (2DoFPI). The performance of the proposed UPQC is significantly improved compared to the conventional control strategy. The feasibility of the proposed UPQC control scheme is validated through the simulations.
The International Journal of Engineering & Science is aimed at providing a platform for researchers, engineers, scientists, or educators to publish their original research results, to exchange new ideas, to disseminate information in innovative designs, engineering experiences and technological skills. It is also the Journal's objective to promote engineering and technology education. All papers submitted to the Journal will be blind peer-reviewed. Only original articles will be published.
The papers for publication in The International Journal of Engineering& Science are selected through rigorous peer reviews to ensure originality, timeliness, relevance, and readability.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
Fuzzy Logic Controller Based High Frequency Link AC-AC Converter For Voltage ...IJTET Journal
Abstract—In this paper, an advanced high frequency link AC-AC Push-pull cycloconverter for the voltage compensation is proposed in order to maintain the power quality in electric grid. The proposed methodology can be achieve arbitrary output voltage without using large energy storage elements. So that the system is more steadfast and less costly compared with the conventional inverter topology. Additionally, the proposed converter does not contain any line frequency transformer, which reduces the cost further. The control scheme for the push pull cycloconverter employs the fuzzy logic controller based sinusoidal pulse width modulation (SPWM) to accomplish better performance on voltage compensation, like unbalanced voltage harmonics elimination. The simulation results are given to show the effectiveness of the proposed high frequency link AC-AC converter and fuzzy logic controller based SPWM technology
Small Signal Modeling Of Controller For Statcom Used In Distribution System F...IJERA Editor
In this paper non-linear model of the STATCOM is linearized and the following strategies have been adopted .
Hence, a small signal model is adopted here. Here, the grid voltage lags the fundamental component of the
STATCOM converter terminal voltage with a phase angle difference
' '
. Small signal modeling of the phase
angle
' '
and modulation index
' m '
is also done. A single PI-controller for the reactive component current of
the STATCOM has been designed. In this model, the DC-link capacitor voltage is held constant without using a
separate controller. The STATCOM are designed using SVPWM technique. Through adjustment of the
modulation index, fast modulation of the STATCOM reactive power output can be achieved due to high
sensitivity of the same with respect to the output voltage of the STATCOM VSC. The model, with PI controllers
has been simulated in MATLAB/SIMULINK environment with variation of the pre-charge voltage on the DClink
capacitor with linear loads (inductive). Improvement of the power factor of the grid current is achieved for
linear loads.
Research on High Frequency PI Section Control of Electrochemical DC Power Supplyiosrjce
The relatively stable voltage output DC power supply is often required in electrolytic plating
electrochemical reactions. Based on the analysis of several circuit structures, full-bridge configuration
electromagnetic isolation has advantages in efficiency and pressure range. The entire system using voltage
feedback loop PI control method of segmentation and the pressure range is divided into multiple parts
separately controlled. Finally, MATLAB simulation comparison, it was verified that this control method can not
only improve the voltage regulator circuit output voltage range and can reduce the amount of ripple output
voltage waveform
Harmonic Minimization In Multilevel Inverters By Using PSOIDES Editor
Harmonic Elimination in a multilevel inverters is
an optimization problem which is solved by applying particle
swarm optimization (PSO) technique. The derived equation
for the computation of total harmonic distortion (THD) of the
output voltage of the multilevel inverter is used as the objective
function in PSO algorithm. The objective function used is to
reduce the THD of the multilevel inverter and obtain the
corresponding switching angles with the elimination of
possible lower order harmonics. In this paper a pseudo code
based algorithm is proposed to deal with inequality constraints
which will helps in accelerating the optimization process. The
proposed method is applied for seven level cascade inverter to
eliminate the 5th and 7th order harmonics to reduce the total
harmonic distortion .This proposed PSO algorithm is effective
in reducing the total harmonic distortion corresponding the
range of modulation index. The simulation results shows that
the proposed PSO method is indeed capable of obtaining
higher quality of solutions to eliminate 5th and 7th order
harmonics and to reduce the total harmonic distortion of 7-
level cascade inverter
Modified Bidirectional Converter with Current Fed InverterIJPEDS-IAES
A bidirectional dc-dc converter with multiple outputs are concatenated with a
high frequency current source parallel resonant push pull inverter is
presented in this paper. The two outputs are added together and it is taken as
the input source for the inverter. The current source parallel resonant push
pull inverter implemented here with high frequency applications like
induction heating, Fluorescent lighting, Digital signal processing sonar. This
paper proposes a simple photovoltaic power system consists of a
bidirectional converter and a current fed inverter for regulating the load
variations. Solar power is used as the input source for the system. Simulation
of the proposed system is carried out in PSIM software and experimentally
verified the results.
The International Journal of Engineering & Science is aimed at providing a platform for researchers, engineers, scientists, or educators to publish their original research results, to exchange new ideas, to disseminate information in innovative designs, engineering experiences and technological skills. It is also the Journal's objective to promote engineering and technology education. All papers submitted to the Journal will be blind peer-reviewed. Only original articles will be published.
The papers for publication in The International Journal of Engineering& Science are selected through rigorous peer reviews to ensure originality, timeliness, relevance, and readability.
A Simplified Design and Modeling of Boost Converter for Photovoltaic Sytem IJECEIAES
The Photovoltaic standalone system is gaining its high importance mostly for rural application like pv water pumping, solar lighting, battery charging etc.Considering environmental effects and scarcity of fossil fuel the trend has developed towards the use of more and more renewable energy.In this paper a basic circuit of boost converter is designed in MATLAB/Simulink with constant dc source voltage. However a comparative study has also been done for the converter connected with pv system directly with the converter connected with mppt tracking technique. Perturb and Observance (P&O) algorithm is implemented for providing the necessary duty pulse and makes the system operate at maximum power point.The boost converter connected with PV system without mppt operates at any other point other then the maximum power point and hence the output voltage decreases.But with mppt the proposed system performs better.
Soft Switched Multi-Output Flyback Converter with Voltage DoublerIJPEDS-IAES
A novel multi-output voltage doubler circuit with resonant switching
technique is proposed in this paper. The resonant topology in the primary
side of the flyback transformer switches the device either at zero voltage or
current thus optimizing the switching devices by mitigating the losses. The
voltage doubler circuit introduced in the load side increases the voltage by
twice the value thereby increasing the load power and density. The proposed
Multi-output Isolated Converter removes the need for mutiple SMPS units
for a particular application. This reduces the size and weight of the
converters considerably leading to a greater payload. This paper aims at
optimizing the proposed converter with some design changes. The results
obtained from the hardware prototype are given in a comprehensive manner
for a 3.5W converter operating at output voltages of 5V and 3.3V at 50 kHz
switching frequency. The converter output is regulated with the PI controller
designed with SG3523 IC. The effects of load and line regulation for ±20%
variations are analyzed in detail.
Analysis of a Quasi Resonant Switch Mode Power Supply for Low Voltage Applica...IDES Editor
QRC provides efficient and regulated switch mode
power supplies for robotic and satellite applications. This paper
addresses the enhanced controller techniques for high
frequency isolation based push-pull Quasi Resonant
Converter. This technique is similar to the conventional PI
controller technique but varies only the enhancement
constants to improve the time domain response of the
converter. The proposed converter is designed for low output
voltage and power rating, characteristically 5V and 5 W, with
the comprehension of current design trends towards enhanced
performance. At the primary stage, to validate the design of
the converter, simulation is performed in PSIM for ±50% load
variations. A prototype model of this converter is developed.
The results obtained from the experimental set-up are
presented and analysed in detail. The results reveal the
superiority of the proposed method.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
Implementation for Controller to Unified Single Phase Power Flow Using Digita...IJERA Editor
Presenting in his paper, Digital signal processor (DSP)-based implementation of a single phase unified power flow controller (UPFC). For shunt side and series side An efficient UPFC control algorithm is achieved. Discussing the laboratory experimental results using DC source are taken as an UPFC linked by two ll-bridge PWM voltage source converters.
Direct Torque Control of Induction Motor Drive Fed from a Photovoltaic Multil...IJERA Editor
This paper presents Direct Torque Control (DTC) using Space Vector Modulation (SVM) for an induction motor drive fed from a photovoltaic multilevel inverter (PV-MLI). The system consists of two main parts PV DC power supply (PVDC) and MLI. The PVDC is used to generate DC isolated sources with certain ratios suitable for the adopted MLI. Beside the hardware system, the control system which uses the torque and speed estimation to control the load angle and to obtain the appropriate flux vector trajectory from which the voltage vector is directly derived based on direct torque control methods. The voltage vector is then generated by a hybrid multilevel inverter by employing space vector modulation (SVM). The inverter high quality output voltage which leads to a high quality IM performances. Besides, the MLI switching losses is very low due to most of the power cell switches are operating at nearly fundamental frequency. Some selected simulation results are presented for system validation.
International Journal of Engineering Research and DevelopmentIJERD Editor
Electrical, Electronics and Computer Engineering,
Information Engineering and Technology,
Mechanical, Industrial and Manufacturing Engineering,
Automation and Mechatronics Engineering,
Material and Chemical Engineering,
Civil and Architecture Engineering,
Biotechnology and Bio Engineering,
Environmental Engineering,
Petroleum and Mining Engineering,
Marine and Agriculture engineering,
Aerospace Engineering.
Unified Power Quality Conditioner Model Based with Series and Shunt FiltersIAES-IJPEDS
With the increase of the complexion in the power distribution system, it is very possible that several kinds of power quality disturbances are happened in a power distribution system simultaneously.This paper proposes a unified power quality conditioner (UPQC) including a series and a shunt active power filter (APF) to compensate harmonics in both the distorted supply voltage and nonlinear load current. In the series APF control scheme, a proportional-integral (PI) controller, meanwhile a PI controller and are designed in the shunt APF control scheme to relieve harmonic currents produced by nonlinear loads. The DC voltage is maintained constant using Two degree of freedom proportional integral voltage controller (2DoFPI). The performance of the proposed UPQC is significantly improved compared to the conventional control strategy. The feasibility of the proposed UPQC control scheme is validated through the simulations.
The International Journal of Engineering & Science is aimed at providing a platform for researchers, engineers, scientists, or educators to publish their original research results, to exchange new ideas, to disseminate information in innovative designs, engineering experiences and technological skills. It is also the Journal's objective to promote engineering and technology education. All papers submitted to the Journal will be blind peer-reviewed. Only original articles will be published.
The papers for publication in The International Journal of Engineering& Science are selected through rigorous peer reviews to ensure originality, timeliness, relevance, and readability.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
Fuzzy Logic Controller Based High Frequency Link AC-AC Converter For Voltage ...IJTET Journal
Abstract—In this paper, an advanced high frequency link AC-AC Push-pull cycloconverter for the voltage compensation is proposed in order to maintain the power quality in electric grid. The proposed methodology can be achieve arbitrary output voltage without using large energy storage elements. So that the system is more steadfast and less costly compared with the conventional inverter topology. Additionally, the proposed converter does not contain any line frequency transformer, which reduces the cost further. The control scheme for the push pull cycloconverter employs the fuzzy logic controller based sinusoidal pulse width modulation (SPWM) to accomplish better performance on voltage compensation, like unbalanced voltage harmonics elimination. The simulation results are given to show the effectiveness of the proposed high frequency link AC-AC converter and fuzzy logic controller based SPWM technology
Small Signal Modeling Of Controller For Statcom Used In Distribution System F...IJERA Editor
In this paper non-linear model of the STATCOM is linearized and the following strategies have been adopted .
Hence, a small signal model is adopted here. Here, the grid voltage lags the fundamental component of the
STATCOM converter terminal voltage with a phase angle difference
' '
. Small signal modeling of the phase
angle
' '
and modulation index
' m '
is also done. A single PI-controller for the reactive component current of
the STATCOM has been designed. In this model, the DC-link capacitor voltage is held constant without using a
separate controller. The STATCOM are designed using SVPWM technique. Through adjustment of the
modulation index, fast modulation of the STATCOM reactive power output can be achieved due to high
sensitivity of the same with respect to the output voltage of the STATCOM VSC. The model, with PI controllers
has been simulated in MATLAB/SIMULINK environment with variation of the pre-charge voltage on the DClink
capacitor with linear loads (inductive). Improvement of the power factor of the grid current is achieved for
linear loads.
Research on High Frequency PI Section Control of Electrochemical DC Power Supplyiosrjce
The relatively stable voltage output DC power supply is often required in electrolytic plating
electrochemical reactions. Based on the analysis of several circuit structures, full-bridge configuration
electromagnetic isolation has advantages in efficiency and pressure range. The entire system using voltage
feedback loop PI control method of segmentation and the pressure range is divided into multiple parts
separately controlled. Finally, MATLAB simulation comparison, it was verified that this control method can not
only improve the voltage regulator circuit output voltage range and can reduce the amount of ripple output
voltage waveform
Harmonic Minimization In Multilevel Inverters By Using PSOIDES Editor
Harmonic Elimination in a multilevel inverters is
an optimization problem which is solved by applying particle
swarm optimization (PSO) technique. The derived equation
for the computation of total harmonic distortion (THD) of the
output voltage of the multilevel inverter is used as the objective
function in PSO algorithm. The objective function used is to
reduce the THD of the multilevel inverter and obtain the
corresponding switching angles with the elimination of
possible lower order harmonics. In this paper a pseudo code
based algorithm is proposed to deal with inequality constraints
which will helps in accelerating the optimization process. The
proposed method is applied for seven level cascade inverter to
eliminate the 5th and 7th order harmonics to reduce the total
harmonic distortion .This proposed PSO algorithm is effective
in reducing the total harmonic distortion corresponding the
range of modulation index. The simulation results shows that
the proposed PSO method is indeed capable of obtaining
higher quality of solutions to eliminate 5th and 7th order
harmonics and to reduce the total harmonic distortion of 7-
level cascade inverter
Harmonic Minimization In Multilevel Inverters By Using PSO
Similar to Electrical Discharge Machining Flyback Converter using UC3842 Current Mode PWM ControllerElectrical Discharge Machining Flyback Converter using UC3842 Current Mode PWM Controller
Modified Bidirectional Converter with Current Fed InverterIJPEDS-IAES
A bidirectional dc-dc converter with multiple outputs are concatenated with a
high frequency current source parallel resonant push pull inverter is
presented in this paper. The two outputs are added together and it is taken as
the input source for the inverter. The current source parallel resonant push
pull inverter implemented here with high frequency applications like
induction heating, Fluorescent lighting, Digital signal processing sonar. This
paper proposes a simple photovoltaic power system consists of a
bidirectional converter and a current fed inverter for regulating the load
variations. Solar power is used as the input source for the system. Simulation
of the proposed system is carried out in PSIM software and experimentally
verified the results.
The International Journal of Engineering & Science is aimed at providing a platform for researchers, engineers, scientists, or educators to publish their original research results, to exchange new ideas, to disseminate information in innovative designs, engineering experiences and technological skills. It is also the Journal's objective to promote engineering and technology education. All papers submitted to the Journal will be blind peer-reviewed. Only original articles will be published.
The papers for publication in The International Journal of Engineering& Science are selected through rigorous peer reviews to ensure originality, timeliness, relevance, and readability.
A Simplified Design and Modeling of Boost Converter for Photovoltaic Sytem IJECEIAES
The Photovoltaic standalone system is gaining its high importance mostly for rural application like pv water pumping, solar lighting, battery charging etc.Considering environmental effects and scarcity of fossil fuel the trend has developed towards the use of more and more renewable energy.In this paper a basic circuit of boost converter is designed in MATLAB/Simulink with constant dc source voltage. However a comparative study has also been done for the converter connected with pv system directly with the converter connected with mppt tracking technique. Perturb and Observance (P&O) algorithm is implemented for providing the necessary duty pulse and makes the system operate at maximum power point.The boost converter connected with PV system without mppt operates at any other point other then the maximum power point and hence the output voltage decreases.But with mppt the proposed system performs better.
Soft Switched Multi-Output Flyback Converter with Voltage DoublerIJPEDS-IAES
A novel multi-output voltage doubler circuit with resonant switching
technique is proposed in this paper. The resonant topology in the primary
side of the flyback transformer switches the device either at zero voltage or
current thus optimizing the switching devices by mitigating the losses. The
voltage doubler circuit introduced in the load side increases the voltage by
twice the value thereby increasing the load power and density. The proposed
Multi-output Isolated Converter removes the need for mutiple SMPS units
for a particular application. This reduces the size and weight of the
converters considerably leading to a greater payload. This paper aims at
optimizing the proposed converter with some design changes. The results
obtained from the hardware prototype are given in a comprehensive manner
for a 3.5W converter operating at output voltages of 5V and 3.3V at 50 kHz
switching frequency. The converter output is regulated with the PI controller
designed with SG3523 IC. The effects of load and line regulation for ±20%
variations are analyzed in detail.
Analysis of a Quasi Resonant Switch Mode Power Supply for Low Voltage Applica...IDES Editor
QRC provides efficient and regulated switch mode
power supplies for robotic and satellite applications. This paper
addresses the enhanced controller techniques for high
frequency isolation based push-pull Quasi Resonant
Converter. This technique is similar to the conventional PI
controller technique but varies only the enhancement
constants to improve the time domain response of the
converter. The proposed converter is designed for low output
voltage and power rating, characteristically 5V and 5 W, with
the comprehension of current design trends towards enhanced
performance. At the primary stage, to validate the design of
the converter, simulation is performed in PSIM for ±50% load
variations. A prototype model of this converter is developed.
The results obtained from the experimental set-up are
presented and analysed in detail. The results reveal the
superiority of the proposed method.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
Closed Loop Analysis of Bridgeless SEPIC Converter for Drive ApplicationIJPEDS-IAES
In this paper closed loop analysis of Single phase AC-DC Bridgeless Single
Ended Primary Inductance Converter (SEPIC) for Power Factor Correction
(PFC) rectifier is analyzed. In this topology the absence of an input diode
bridge and the due to presence of two semiconductor switches in the current
flowing path during each switching cycle which will results in lesser
conduction losses and improved thermal management compared to the
conventional converters. In this paper the operational principles, Frequency
analysis, and design equations of the proposed converter are described in
detail. Performance of the proposed SEPIC PFC rectifier is carried out using
Matlab Simulink software and results are presented.
Transformer Less Voltage Quadrupler Based DC-DC Converter with Coupled Induct...IJPEDS-IAES
In this paper a voltage quadrupler dc-dc converter with coupled inductor
and π filter is presented. The use of the coupled inductor reduces the high
leakage inductance which is present in a transformer enabled converter.
The output ripples in the converter is reduced by providing a π filter.
The interleaved voltage quadrupler is used in this system in order to boost the
output voltage. The voltage multiplier improves the output voltage gain.
The main advantage of this system is more voltage gain when compared with
the transformer eneabled circuit and the overall efficiency of the system is
improved. The circuit is simple to control. As a final point of this research,
the simulation and the hardware investigational results are presented to
demonstrate the effectiveness of this proposed converter.
DESIGN, SIMULATION, IMPLEMENTATION AND CONTROL OF PLC BASED INTEGRAL CYCLE CO...IAEME Publication
The Class of ac power controllers consists of Solid State Power Controller (SSPC) which connects and disconnects the load to the supply according to the required power. Two important voltage control techniques are commonly used for heating power control in ac power controller are Phase Control Switching and Integral Cycle Control. In case that a PCS is used for the resistive load, it can produce higher order harmonics and heavy inrush current while switching on in a cold start. In the proposed method, a disadvantage of phase controlled is removed. In this paper authors have reported simulated results, design methodology, implementation and Control of PLC Based Integral Cycle Control (ICC) method for Resistance Spot Welding (RSW).
This paper proposes an alternative topology of an inverter to the existing topologies available in the market. A prototype is intended with the purpose of investigates the possibility of designing an inverter using two Boost Converters. This project initialized with a series of simulations using Matlab in order to determine the feasibility of the proposed topology. The next step is the design and development of the proposed prototype where suitable electronics components are chosen based on the simulation result. A PIC microcontroller is used to control the proposed prototype where a control scheme is created based on the programming in the microcontroller. The performance of the proposed prototype has been verified to be optimum by several practical testing using different values of capacitor, inductor and duty cycle. Lastly, data and analysis are presented in a proper mannered way. In the end, this project intends to produce stepped-up square wave output voltage waveform by proper controlling of two Boost Converters.
Model of Pulsed Electrical Discharge Machining (EDM) using RL CircuitIJPEDS-IAES
This article presents a model of pulsed Electrical Discharge Machining (EDM) using RL circuit. There are several mathematical models have been successfully developed based on the initial, ignition and discharge phase of current and voltage gap. According to these models, the circuit schematic of transistor pulse power generator has been designed using electrical model in Matlab Simulink software to identify the profile of voltage and current during machining process. Then, the simulation results are compared with the experimental results.
Bridgeless CUK Power Factor Corrector with Regulated Output Voltagepaperpublications3
Abstract:A single-phase, bridgeless Cuk AC/DC power factor correction (PFC) rectifier with regulated positive output voltage is proposed in this work. For low output voltage product applications, the rectifier is designed to convert high input voltage to low output voltage. This work presents bridgeless single-phase AC-DC power factor correction (PFC) rectifier based on Cuk topology. The topology does not possess input diode bridge and have only single semiconductor switches in the current owing path during each interval of the switching cycle, which resulting in less conduction losses and better thermal management. This topology is designed to work in discontinuous conduction mode (DCM). The advantages of Cuk converter are also available when bridgeless circuit topology is introduced. The operation is symmetrical in two half-line cycles of input voltage. In conventional, output voltage varies according to input voltage. A closed loop control technique is designed to regulate the output voltage in the desired level. Performance and applicability of this converter is presented on the basis of simulation in MATLAB/SIMULINK.
Design and Development of Power Electronic Controller for Grid-connected PV A...IJAPEJOURNAL
Design and simulation of a simple power electronic interface for grid-connected PV array has been proposed using boost converter and line-commutated inverter with maximum power point tracking (MPPT) controller. The output of PV array varies with irradiation, and hence the duty cycle of the PI controller is adjusted automatically to supply a constant DC voltage to the inverter circuit, the output of which is directly connected to the grid. The MPPT controller extracts maximum power from the solar array and feeds it to the single-phase utility grid. The proposed scheme has been modeled in the MATLAB 7.1 software and the complete system has been simulated for open loop and closed loop configurations. The active power fed to the grid is taken for different firing angles in open loop mode and the firing angle for maximum power has been determined. This is compared with the firing angle obtained from the closed loop mode and found that both results agree with each other.
A Integrated Technique of SIDO PFC Fly back Converter in power systemIJMTST Journal
Energy saving is the major international efforts to control down the global warming .Power electronics based devices has being improving day by day for saving the electrical energy in the power grids. The govt. of India is also contributing several projects based on energy conservation. The Designing of a single-inductor dual output (SIDO) fly-back power factor correction (PFC) converter is proposed, in which the PFC and power conversion are done at the same time, multiplexing of a single-inductor is implemented through which each output can be regulated independently. The converter will be operating under in critical conduction mode (CRM). A SIDO PFC converter is a system of dual efficient DC output obtained from the AC source, it can also be replaced by solar panel and our system is capable of running a dc motor also, fly back converter can be used in both ac-dc and dc-dc conversion process. The efficiency along with power factor, total harmonic distortion (THD), settling time and output accuracy of this converter will be improved by implementing the neural network as controllers in the system
International Journal of Engineering Research and DevelopmentIJERD Editor
International Journal of Engineering Research and Development
Similar to Electrical Discharge Machining Flyback Converter using UC3842 Current Mode PWM ControllerElectrical Discharge Machining Flyback Converter using UC3842 Current Mode PWM Controller (20)
Inter-Area Oscillation Damping using an STATCOM Based Hybrid Shunt Compensati...IJPEDS-IAES
FACTS devices are one of the latest technologies which have been used to
improve power system dynamic and stability during recent years. However,
widespread adoption of this technology has been hampered by high cost
and reliability concerns. In this paper an economical phase imbalanced shunt
reactive compensation concept has been introduced and its ability for power
system dynamic enhancement and inter-area oscillation damping are
investigated. A hybrid phase imbalanced scheme is a shunt capacitive
compensation scheme, where two phases are compensated by fixed shunt
capacitor (C) and the third phase is compensated by a Static Synchronous
Compensator (STATCOM) in shunt with a fixed capacitor (CC). The power
system dynamic stability enhancement would be achieved by adding
a conventional Wide Area Damping Controller (WADC) to the main control
loop of the single phase STATCOM. Two different control methodologies
are proposed: a non-optimized conventional damping controller
and a conventional damping controller with optomised parameters that are
added to the main control loop of the unbalanced compensator in order to
damp the inter area oscillations. The proposed arrangement would, certainly,
be economically attractive when compared with a full three-phase
STATCOM. The proposed scheme is prosperously applied in a 13-bus
six-machine test system and various case studies are conducted to
demonstrate its ability in damping inter-area oscillations and power system
dynamic enhancement.
Fuzzy Gain-Scheduling Proportional–Integral Control for Improving the Speed B...IJPEDS-IAES
In this article, we have set up a vector control law of induction machine
where we tried different type of speed controllers. Our control strategy is of
type Field Orientated Control (FOC). In this structure we designed a Fuzzy
Gain-Scheduling Proportional–Integral (Pi) controller to obtain best result
regarding the speed of induction machine. At the beginning we designed a Pi
controller with fixed parameters. We came up to these parameters by
identifying the transfer function of this controller to that of Broïda (second
order transfer function). Then we designed a fuzzy logic (FL) controller.
Based on simulation results, we highlight the performances of each
controller. To improve the speed behaviour of the induction machine, we
have designend a controller called “Fuzzy Gain-Scheduling Proportional–
Integral controller” (FGS-PI controller) which inherited the pros of the
aforementioned controllers. The simulation result of this controller will
strengthen its performances.
Advance Technology in Application of Four Leg Inverters to UPQCIJPEDS-IAES
This article presents a novel application of four leg inverter with
conventional Sinusoidal Pulse Width Modulation (SPWM) Scheme to
Unified Power Quality Conditioner (UPQC). The Power Quality problem
became burning issues since the starting of high voltage AC transmission
system. Hence, in this article it has been discussed to mitigate the PQ issues
in high voltage AC systems through a three phase Unified Power Quality
Conditioner (UPQC) under various conditions, such as harmonic mitigation
scheme, non linear loads, sag and swell conditions as well. Also, it proposes
to control harmoincs with various artificial intelligent techniques. Thus
application of these control technique such as Neural Networks (ANN)
Fuzzy Logic makes the system performance in par with the standards
and also compared with existing system. The simulation results based on
MATLAB/Simulink are discussed in detail to support the concept developed
in the paper.
Modified SVPWM Algorithm for 3-Level Inverter Fed DTC Induction Motor DriveIJPEDS-IAES
In this paper, a modified space vector pulse width modulation (MSVPWM)
algorithm is developed for 3-level inverter fed direct torque controlled
induction motor drive (DTC-IMD). MSVPWM algorithm simplifies
conventional space vector pulse width modulation (CSVPWM) algorithm for
multilevel inverter (MLI), whose complexity lies in sector/subsector/subsubsector
identification; which will commensurate with number of levels. In
the proposed algorithm sectors are identified as in two level inverter
and subsectors/sub-subsectors are identified by shifting the original reference
vector to sector 1 (S1). This is valid due to the fact that a three level space
vector plane is a composition of six two level space planes, and are
symmetrical with reference to six pivot states. Switching state/sequence
selection is also very important while dealing with SVPWM strategy for
MLI. In the proposed algorithm out of 27 available switching states apt
switching state is selected based on sector and subsector number, such that
voltage ripple is considerably less. To validate the proposed algorithm, it is
tested on a three level neutral point clamped (NPC) inverter fed DTC-IMD.
The performance of the MSVPWM algorithm is analyzed by comparing no
load stator current ripple of the three level DTC-IMD with two level
DTC-IMD. Significant reduction in steady state torque and flux ripple is
observed. Hence, reduced acoustic noise is a distinctive facet of the proposed
method.
Modelling of a 3-Phase Induction Motor under Open-Phase Fault Using Matlab/Si...IJPEDS-IAES
The d-q model of Induction Motors (IMs) has been effectively used as an
efficient method to analyze the performance of the induction machines. This
study presents a step by step Matlab/Simulink implementation
of a star-connected 3-phase IM under open-phase fault (faulty 3-phase IM)
using d-q model. The presented technique in this paper can be simply
implemented in one block and can be made available for control purposes.
The simulated results provide to show the behavior of the star-connected 3-phase IM under open-phase fault condition.
Performance Characteristics of Induction Motor with FielIJPEDS-IAES
With development of power electronics and control Theories, the AC motor
control becomes easier. So the AC motors are used instead of the DC motor
in the drive applications. With this development, a several methods of control
are invented. The field oriented control and direct torque control are from the
best methods to control the drive systems. This paper is compared between
the field oriented control and direct torque control to show the advantages
and disadvantages of these methods of controls. This study discussed the
effects of these methods of control on the total harmonic distortion of the
current and torque ripples. This occurs through study the performance
characteristics of the AC motor. The motor used in this study is an induction
motor. This study is simulated through the MATLAB program.
A Novel Modified Turn-on Angle Control Scheme for Torque- Ripple Reduction in...IJPEDS-IAES
In recent years, Switched Reluctance Motors (SRM) have been dramatically
considered with both researchers and industries. SRMs not only have a
simple and reliable structure, but also have low cost production process.
However, discrete torque production of SRM along with intensive magnetic
saturation in stator and rotor cores are the major drawbacks of utilizing in
variety of industrial applications and also causes the inappropriate torque
ripples. In this paper, a modified logical-rule-based Torque Sharing Function
(TSF) method is proposed considering turn-on angle control. The optimized
turn-on angle for conducting each phase is achieved by estimating the
inductance curve in the vicinity of unaligned position and based on an
analytical solution for each phase voltage equation. Simulation results on a
four-phase switched reluctance motor and comparison with the conventional
methods validates the effectiveness of the proposed method.
Modeling and Simulation of Induction Motor based on Finite Element AnalysisIJPEDS-IAES
This paper presents the development of a co-simulation platform of induction
motor (IM). For the simulation, a coupled model is introduced which
contains the control, the power electronics and also the induction machine.
Each of these components is simulated in different software environments.
So, this study provides an advanced modeling and simulation tools for IM
which integrate all the components into one common simulation platform
environment. In this work, the IM is created using Ansys-Maxwell based on
Finite Element Analysis (FEA), whereas the power electronic converter is
developed in Ansys-Simplorer and the control scheme is build in MATLABSimulink
environment. Such structure can be useful for accurate design
and allows coupling analysis for more realistic simulation. This platform is
exploited to analyze the system models with faults caused by failures of
different drive’s components. Here, two studies cases are presented: the first
is the effects of a faulty device of the PWM inverter, and the second case is
the influence of the short circuit of two stator phases. In order to study the
performance of the control drive of the IM under fault conditions,
a co-simulation of the global dynamic model has been proposed to analyze
the IM behavior and control drives. In this work, the co-simulation has been
performed; furthermore the simulation results of scalar control allowed
verifying the precision of the proposed FEM platform.
Comparative Performance Study for Closed Loop Operation of an Adjustable Spee...IJPEDS-IAES
In this paper an extensive comparative study is carried out between PI
and PID controlled closed loop model of an adjustable speed Permanent
Magnet Synchronous Motor (PMSM) drive. The incorporation of Sinusoidal
Pulse Width Modulation (SPWM) strategy establishes near sinusoidal
armature phase currents and comparatively less torque ripples without
sacrificing torque/weight ratio. In this closed loop model of PMSM drive, the
information about reference speed is provided to a speed controller, to ensure
that actual drive speed tracks the reference speed with ideally zero steady
state speed error. The entire model of PMSM closed loop drive is divided
into two loops, inner loop current and outer loop speed. By taking the
different combinations of two classical controllers (PI & PID) related with
two loop control structure, different approximations are carried out. Hence a
typical comparative study is introduced to familiar with the different
performance indices of the system corresponding to time domain and
frequency domain specifications. Therefore overall performance of closed
loop PMSM drive is tested and effectiveness of controllers will be
determined for different combinations.
Novel Discrete Components Based Speed Controller for Induction MotorIJPEDS-IAES
This paper presents an electronic design based on general purpose discrete
components for speed control of a single phase induction motor drive. The
MOSFETs inverter switching is controlled using Sampled Sinusoidal Pulse
Width Modulation (SPWM) techniques with V/F method based on Voltage
Controlled Oscillator (VCO). The load power is also controlled by a novel
design to produce a suitable SPWM pulse. The proposed electronic system
has ability to control the output frequency with flexible setting of lower limit
to less than 1 Hz and to higher frequency limits to 55 Hz. Moreover, the
proposed controller able to control the value of load voltage to frequency
ratio, which plays a major parameter in the function of IM speed control.
Furthermore, the designed system is characterized by easy manufacturing
and maintenance, high speed response, low cost, and does not need to
program steps as compared to other systems based on Microcontroller
and digital signal processor (DSP) units. The complete proposed electronic
design is made by the software of NI Multisim version 11.0 and all the
internal sub-designs are shown in this paper. Simulation results show the
effectiveness of electronic design for a promising of a high performance IM
PWM drive.
Sensorless Control of a Fault Tolerant PMSM Drives in Case of Single-Phase Op...IJPEDS-IAES
This paper introduces a sensorless-speed-controlled PMSM motor fed by a
four-leg inverter in case of a single phase open circuit fault regardless in
which phase is the fault. To minimize the system performance degradation
due to a single phase open circuit fault, a fault tolerant control strategy that
includes taking appropriate actions to control the two remaining healthy
currents is used in addition to use the fourth leg of the inverter. Tracking the
saliency is done through measuring the dynamic current responses of the
healthy phases of the PMSM motor due the IGBT switching actions using the
fundamental PWM method without introducing any modification to the
operation of the fourth leg of the inverter. Simulation results are provided to
verify the effectiveness of the proposed strategy for sensorless controlling of
a PMSM motor driven by a fault-tolerant four-phase inverter over a wide
speed ranges under the case of a single phase open circuit.
Improved Stator Flux Estimation for Direct Torque Control of Induction Motor ...IJPEDS-IAES
Stator flux estimation using voltage model is basically the integration of the
induced stator back electromotive force (emf) signal. In practical
implementation the pure integration is replaced by a low pass filter to avoid
the DC drift and saturation problems at the integrator output because of the
initial condition error and the inevitable DC components in the back emf
signal. However, the low pass filter introduces errors in the estimated stator
flux which are significant at frequencies near or lower than the cutoff
frequency. Also the DC components in the back emf signal are amplified at
the low pass filter output by a factor equals to . Therefore, different
integration algorithms have been proposed to improve the stator flux
estimation at steady state and transient conditions. In this paper a new
algorithm for stator flux estimation is proposed for direct torque control
(DTC) of induction motor drives. The proposed algorithm is composed of a
second order high pass filter and an integrator which can effectively
eliminates the effect of the error initial condition and the DC components.
The amplitude and phase errors compensation algorithm is selected such that
the steady state frequency response amplitude and phase angle are equivalent
to that of the pure integrator and the multiplication and division by stator
frequency are avoided. Also the cutoff frequency selection is improved; even
small value can filter out the DC components in the back emf signal. The
simulation results show the improved performance of the induction motor
direct torque control drive with the proposed stator flux estimation algorithm.
The simulation results are verified by the experimental results.
Minimization of Starting Energy Loss of Three Phase Induction Motors Based on...IJPEDS-IAES
The purpose of this paper is to minimize energy losses consumed by three
phase induction motors during starting with wide range of load torque from
no load to full load. This will limit the temperature rise and allows for more
numbers of starting during a definite time. Starting energy losses
minimization is achieved by controlling the rate of increasing voltage
and frequency to start induction motor under certain load torque within a
definite starting time. Optimal voltage and frequency are obtained by particle
swarm optimization (PSO) tool according to load torque. Then, outputs of the
PSO are used to design a neuro-fuzzy controller to control the output voltage
and frequency of the inverter during starting for each load torque. The
starting characteristics using proposed method are compared to that of direct
on line and V/F methods. A complete model of the system is developed using
SIMULINK/MATLAB.
Hardware Implementation of Solar Based Boost to SEPIC Converter Fed Nine Leve...IJPEDS-IAES
Multi level inverters are widely used in high power applications because of
low harmonic distortion. This paper deals with the simulation
and implementation of PV based boost to SEPIC converter with multilevel
inverter. The output of PV system is stepped up using boost to sepic
converter and it is converted into AC using a multilevel inverter.
The simulation and experimental results with the R load is presented in this
paper. The FFT analysis is done and the THD values are compared. Boost to
SEPIC converter is proposed to step up the voltage to the required value. The
experimental results are compared with the simulation results. The results
indicate that nine level inverter system has better performance than seven
level inverter system.
IRAMY Inverter Control for Solar Electric VehicleIJPEDS-IAES
Solar Electric Vehicles (SEV) are considered the future vehicles to solve the issues of air pollution, global warming, and the rapid decreases of the petroleum resources facing the current transportation technology. However, SEV are still facing important technical obstacles to overcome. They include batteries energy storage capacity, charging times, efficiency of the solar panels and electrical propulsion systems. Solving any of those problems and electric vehicles will compete-complement the internal combustion engines vehicles. In the present work, we propose an electrical propulsion system based on three phase induction motor in order to obtain the desired speed and torque with less power loss. Because of the need to lightweight nature, small volume, low cost, less maintenance and high efficiency system, a three phase squirrel cage induction motor (IM) is selected in the electrical propulsion system. The IM is fed from three phase inverter operated by a constant V/F control method and Space Vector Pulse Width Modulation (SVPWM) algorithm. The proposed control strategy has been implemented on the texas instruments TM320F2812 Digital Signal Processor (DSP) to generate SVPWM signal needed to trigger the gates of IGBT based inverter. The inverter used in this work is a three phase inverter IRAMY20UP60B type. The experimental results show the ability of the proposed control strategy to generate a three-phase sine wave signal with desired frequency. The proposed control strategy is experimented on a locally manufactured EV prototype. The results show that the EV prototype can be propelled to speed up to 60km/h under different road conditions.
Design and Implementation of Single Phase AC-DC Buck-Boost Converter for Powe...IJPEDS-IAES
This paper discusses the Power Factor Correction (PFC) for single phase AC-DC Buck-Boost Converter (BBC) operated in Continuous Conduction Mode (CCM) using inductor average current mode control. The proposed control technique employs Proportional-Integral (PI) controller in the outer voltage loop and the Inductor Average Current Mode Control (IACMC) in the inner current loop for PFC BBC. The IACMC has advantages such as robustness when there are large variations in line voltage and output load. The PI controller is developed by using state space average model of BBC. The simulation of the proposed system with its control circuit is implemented in MatLab/Simulink. The simulation results show a nearly unity power factor can be attained and there is almost no change in power factor when the line frequency is at various ranges. Experimental results are provided to show its validity and feasibility.
Improvement of Wind farm with PMSG using STATCOMIJPEDS-IAES
This paper studies about the dynamic performance of the Permanent Magnet Synchronous Generator with Static Synchronous Compensator (STATCOM) for Wind farm integration. A whole dynamic model of wind energy conversion system (WECS) with PMSG and STATCOM are established in a MATLAB environment. With this model the dynamic behaviour of the generator and the overall system has been studied to determine the performance of them with and without STATCOM. Final results portrays that the WECS based PMSG with STATCOM improves the transient response of the wind farm when the system is in fault.
Modeling and Control of a Doubly-Fed Induction Generator for Wind Turbine-Gen...IJPEDS-IAES
This paper presents a vector control direct (FOC) of double fed induction generator intended to control the generated stator powers. This device is intended to be implemented in a variable-speed wind-energy conversion system connected to the grid. In order to control the active and reactive power exchanged between the machine stator and the grid, the rotor is fed by a bi-directional converter. The DFIG is controlled by standard relay controllers. Details of the control strategy and system simulation were performed using Simulink and the results are presented in this here to show the effectiveness of the proposed control strategy.
A Review on Design and Development of high Reliable Hybrid Energy Systems wit...IJPEDS-IAES
Hybrid Energy system is a combination of two or more different types of energy resources. Now a day this hybrid energy system plays key role in various remote area power applications. Hybrid energy system is more reliable than single energy system. This paper deals with high reliable hybrid energy system with solar, wind and micro hydro resources. The proposed hybrid system cable of multi mode operation and high reliable due to non communicated based controllers (Droop Characteristic Control) are used for optimal power sharing. Size of battery can be reduced because hydro used as back up source and Maximum power point Tracking also applied to solar and wind energy systems.
Fuzzy Sliding Mode Control for Photovoltaic SystemIJPEDS-IAES
In this study, a fuzzy sliding mode control (FSMC) based maximum power point tracking strategy has been applied for photovoltaic (PV) system. The key idea of the proposed technique is to combine the performances of the fuzzy logic and the sliding mode control in order to improve the generated power for a given set of climatic conditions. Different from traditional sliding mode control, the developed FSMC integrates two parts. The first part uses a fuzzy logic controller with two inputs and 25 rules as an equivalent controller while the second part is designed for an online adjusting of the switching controller’s gain using a fuzzy tuner with one input and one output. Simulation results showed the effectiveness of the proposed approach achieving maximum power point. The fuzzy sliding mode (FSM) controller takes less time to track the maximum power point, reduced the oscillation around the operating point and also removed the chattering phenomena that could lead to decrease the efficiency of the photovoltaic system.
Sachpazis:Terzaghi Bearing Capacity Estimation in simple terms with Calculati...Dr.Costas Sachpazis
Terzaghi's soil bearing capacity theory, developed by Karl Terzaghi, is a fundamental principle in geotechnical engineering used to determine the bearing capacity of shallow foundations. This theory provides a method to calculate the ultimate bearing capacity of soil, which is the maximum load per unit area that the soil can support without undergoing shear failure. The Calculation HTML Code included.
Courier management system project report.pdfKamal Acharya
It is now-a-days very important for the people to send or receive articles like imported furniture, electronic items, gifts, business goods and the like. People depend vastly on different transport systems which mostly use the manual way of receiving and delivering the articles. There is no way to track the articles till they are received and there is no way to let the customer know what happened in transit, once he booked some articles. In such a situation, we need a system which completely computerizes the cargo activities including time to time tracking of the articles sent. This need is fulfilled by Courier Management System software which is online software for the cargo management people that enables them to receive the goods from a source and send them to a required destination and track their status from time to time.
Hybrid optimization of pumped hydro system and solar- Engr. Abdul-Azeez.pdffxintegritypublishin
Advancements in technology unveil a myriad of electrical and electronic breakthroughs geared towards efficiently harnessing limited resources to meet human energy demands. The optimization of hybrid solar PV panels and pumped hydro energy supply systems plays a pivotal role in utilizing natural resources effectively. This initiative not only benefits humanity but also fosters environmental sustainability. The study investigated the design optimization of these hybrid systems, focusing on understanding solar radiation patterns, identifying geographical influences on solar radiation, formulating a mathematical model for system optimization, and determining the optimal configuration of PV panels and pumped hydro storage. Through a comparative analysis approach and eight weeks of data collection, the study addressed key research questions related to solar radiation patterns and optimal system design. The findings highlighted regions with heightened solar radiation levels, showcasing substantial potential for power generation and emphasizing the system's efficiency. Optimizing system design significantly boosted power generation, promoted renewable energy utilization, and enhanced energy storage capacity. The study underscored the benefits of optimizing hybrid solar PV panels and pumped hydro energy supply systems for sustainable energy usage. Optimizing the design of solar PV panels and pumped hydro energy supply systems as examined across diverse climatic conditions in a developing country, not only enhances power generation but also improves the integration of renewable energy sources and boosts energy storage capacities, particularly beneficial for less economically prosperous regions. Additionally, the study provides valuable insights for advancing energy research in economically viable areas. Recommendations included conducting site-specific assessments, utilizing advanced modeling tools, implementing regular maintenance protocols, and enhancing communication among system components.
Water scarcity is the lack of fresh water resources to meet the standard water demand. There are two type of water scarcity. One is physical. The other is economic water scarcity.
Vaccine management system project report documentation..pdfKamal Acharya
The Division of Vaccine and Immunization is facing increasing difficulty monitoring vaccines and other commodities distribution once they have been distributed from the national stores. With the introduction of new vaccines, more challenges have been anticipated with this additions posing serious threat to the already over strained vaccine supply chain system in Kenya.
Quality defects in TMT Bars, Possible causes and Potential Solutions.PrashantGoswami42
Maintaining high-quality standards in the production of TMT bars is crucial for ensuring structural integrity in construction. Addressing common defects through careful monitoring, standardized processes, and advanced technology can significantly improve the quality of TMT bars. Continuous training and adherence to quality control measures will also play a pivotal role in minimizing these defects.
Overview of the fundamental roles in Hydropower generation and the components involved in wider Electrical Engineering.
This paper presents the design and construction of hydroelectric dams from the hydrologist’s survey of the valley before construction, all aspects and involved disciplines, fluid dynamics, structural engineering, generation and mains frequency regulation to the very transmission of power through the network in the United Kingdom.
Author: Robbie Edward Sayers
Collaborators and co editors: Charlie Sims and Connor Healey.
(C) 2024 Robbie E. Sayers
Forklift Classes Overview by Intella PartsIntella Parts
Discover the different forklift classes and their specific applications. Learn how to choose the right forklift for your needs to ensure safety, efficiency, and compliance in your operations.
For more technical information, visit our website https://intellaparts.com
Student information management system project report ii.pdfKamal Acharya
Our project explains about the student management. This project mainly explains the various actions related to student details. This project shows some ease in adding, editing and deleting the student details. It also provides a less time consuming process for viewing, adding, editing and deleting the marks of the students.
2. ISSN: 2088-8694
IJPEDS Vol. 5, No. 2, October 2014 : 261 – 267
262
Current mode control is implemented through two control loops, namely current control loop and a
voltage loop. Current control loop monitor the inductor or transformer primary current information, creates
the voltage controlled current source. Voltage control loop monitors the converters output voltage (flyback
converter), and constantly program the controlled current controller (UC3842) to regulate the output voltage
at a given set point.
UC3842 has been proposed as the integrated Pulse Width Modulation (PWM) for EDM because it
provides an inexpensive controller with good electrical performance of current mode operation. In addition,
UC3842 is optimized for efficient power sequencing of DC to DC converter which is implemented in this
paper.
This paper covers a closed loop current mode controlled flyback converter. MOSFET is used as the
switching element where UC3842 is used as the current mode PWM controller. MATLAB software is
adopted to simulate the behaviors of the converter.
2. PROPOSED CIRCUIT
Fig. 1 shows the poroposed circuit for EDM power generator. It is composed of Flyback converter
circuit with voltage control circuit and current mode PWM controller using UC3842. All components are
assumed to be ideal. The working principle of flyback differs from other SMPS topology structure. The
output voltage and current can be adjusted by altering the duty cycle of the main switch through the feedback
control circuit [8]. UC3842 has been implemented to generate PWM in the proposed circuit.
Figure 1. Circuit diagram of current mode controlled flyback converter
2.1. Flyback Converter Topology
Figure 2 and 3 shows the equivalent circuit of Mode 1 and Mode 2 operation corresponding to the
Switch either in the on or off state respectively.
Figure 2. Mode 1; when Switch on Figure 3. Mode 2; when Switch off
Figure 2 [9] shows a parasitic-elements-free flyback when switch (SW) is closed. The primary of the
transformer is directly connected to the input voltage. Thus, the voltage across the primary inductor Lp is
equal to the input voltage. During this time, there is no current flowing in the secondary side inductor. During
the on time, the diode anode swing negative, thus blocking the current from circulating in the secondary side.
The output capacitor supplies energy to the output load.
3. IJPEDS ISSN: 2088-8694
Electrical Discharge Machining Flyback Converter using UC3842 Current Mode… (Nazriah Mahmud)
263
Figure 3 [9] shows a parasitic-elements-free flyback when switch (SW) is opened. When the switch
is turned off, the voltage across the primary inductor reverses, in an attempt to keep the ampere-turns
constant. However, as the secondary diode now senses a positive voltage on its anode, allowing current to
flow from the transformer. The secondary-side-transformer terminal is now biased to the output voltage, Vout,
by neglecting the diode forward drop. The energy from the transformer core recharges the capacitor and
supplies the load.
2.2. UC3842 Structure
Figure 4 [10] shows the structural block diagram of UC3842. The structure consist of 6 main blocks.
Fully compensated Error Amplifier is provided (A) with access to inverting input and output. The non-
inverting input is internally fixed at the reference voltage of 2.5V and not pinned out. The under-voltage
lockout (B) ensure that Vcc is adequate to make UC3842 fully operate before enabling the output stage. The
oscillator (C) frequency is fixed by external timing capacitor, CT and timing resistor, RT. The oscillator
converts the triangle waveform into rectangular pulse train controlling the operating conditions of the digital
circuit forming the shape of the output pulses (E). The circuit consist of RS flip-flop and logic gate. The
current sense comparator (D) ensures only a single pulse appears at the output during any given oscillator
cycle. The output continues until the voltage at the current sense exceeds the voltage value at the comparator
inverting input. The UC3842 PWM (F) has a single totem-pole output which can be operated to ± 1 A peak
for driving a MOSFET.
Figure 4. UC3842 block diagram
2.3. Working Principle of the Feedback Control Circuit
There are two loop implemented by using UC3842 namely voltage feedback loop and current
feedback loop. Voltage feedback loop consist of reference voltage of 2.5 V and error amplifier. It is
connected with peripheral components by COMP and FB pin where the gain and bandwidth of the error
amplifier can be adjusted. Reference voltage of current comparator is the acquired voltage from partial
voltage of R resistance after output voltage of error amplifier passes through 2R.
Current feedback loop consist of peripheral current sampling circuit and internal current comparator
where reference voltage is acquired from partial voltage of output voltage of error amplifier. Output pulse
will be cut off if comparing the voltage with DC feedback voltage directly. Width of output pulse can be
reached by changing gain of error amplifier of parameters of current feedback sampling circuit.
The control circuit consist of following component as shown in Figure 5.
1) Resistance Rs is used as the current sensor. When SW turn on, the current flow through the Rs;
once the voltage at pin 3 reaches the threshold value, current limiting occur.
2) Oscillator timing capacitor, Ct is charged by Vref through Rt and discharged by an internal current
source where Fs = 1.72/RtCt. Rt and Ct determine both oscillator frequency and maximum duty cycle.
B
FE
B
B
A
4. ISSN: 2088-8694
IJPEDS Vol. 5, No. 2, October 2014 : 261 – 267
264
Figure 5. Control circuit
3. RESULTS AND ANALYSIS
The results is divided into simulation result and experimental result. Both are discussed in the sub-
section below.
3.1. Simulation Result
In this section, simulation results of the proposed circuit are presented and discussed. The simulation
have been done using MATLAB/SIMULINK as shown in Figure 6. Entire control circuit is replaced by error
comparator for voltage feedback loop and PWM generator subsystem for PWM controller. In this study, the
analysis is done by varying the load resistor in order to study the consistency of the output voltage obtain
before an experiment conducted. The load resistor varied from 92.1 Ω to 1014.5 Ω.
Figure 6. Matlab circuit for flyback converter
Figure 7 illustrated the waveform of output voltage during simulation. The output voltage regulated
in between 98 V to 99 V which is the required voltage.
Table 1 discussed the average of output voltage and output current respectively. Since output
voltage has been stabilized, the output current can be adjusted by varying the load resistor without changing
the voltage. Thus, the voltage can stays in the required range in order to obtain required discharge current.
5. IJPEDS ISSN: 2088-8694
Electrical Discharge Machining Flyback Converter using UC3842 Current Mode… (Nazriah Mahmud)
265
Figure 7. Output voltage during simulation
Table 1. Variation of output current and output voltage during simulation
Resistance
(Ω)
Output Current
(A)
Output Voltage
(V)
92.1 1.0740 98.82
122.9 0.8073 99.04
155.0 0.6414 99.20
184.3 0.5402 99.29
312.3 0.3200 99.49
379.2 0.2639 99.54
477.1 0.2102 99.60
1014.5 0.0998 99.69
3.2. Experimental Result
Since simulation using Matlab shows positive response, thus experiment is conducted to verify the
performance of the flyback converter as illustrated in Figure 8. The UC3842 now is implemented as
switching module for flyback converter.
Figure 9 illustrates the Pulse Width Modulation (PWM) waveform measured from the output pin
(Pin 6) of UC3842. The measured frequency is 21.8 kHz.
Figure 8. Experimental set up Figure 9. Pulse Width Modulation (PWM) waveform
The output voltage and output current measured from the experiment are tabulated in Table 2. The
voltage varied in the range of 91 V to 111 V, which is still in the required range.
6. ISSN: 2088-8694
IJPEDS Vol. 5, No. 2, October 2014 : 261 – 267
266
Table 2. Variation of output current and output voltage during experiment
Resistance
(Ω)
Output Current
(A)
Output Voltage
(V)
92.1 0.99 91.2
122.9 0.75 92.2
155.0 0.60 93.0
184.3 0.51 94.0
312.3 0.31 96.8
379.2 0.26 98.6
477.1 0.21 100.2
1014.5 0.11 111.6
4. CONCLUSION
The performance of flyback converter has been simulated using MATLAB and the corresponding
outputs are tabulated. The results highlighted the significant of current mode control which consist of two
feedback loop namely current feedback loop and voltage feedback loop along with a controller UC3842 for
obtaining regulated output of 100V. The hardware model has been constructed. The pulses generated from
the controller UC3842 which uses Pulse Width Modulation technique, drive the gate of the MOSFET to work
as the switch. The output voltage during simulation and experiment is found to be constant and stable.
ACKNOWLEDGEMENTS
The authors would like to acknowledge the financial support of Research Management Centre
(RMC) Universiti Teknologi Malaysia.
REFERENCES
[1] M Gostimirovic, P Kovac, B Skoric, M Sekulic. Effect of electrical pulse parameters on the machining performance
in EDM. Indian Journal of Engineering & Materials Sciences. 2012; 18: 411-415.
[2] O Eyercioglu, MV Cakir, K Gov. Influence of machining parameters on the surface integrity in small-hole electrical
discharge machining. Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering
Manufacture. 2014; 228: 51-61.
[3] K Sandeep. Current Research Trends in Electrical Discharge Machining: A Review. Research Journal of
Engineering Sciences. 2013; 2: 56-60.
[4] YC Lin, YF Chen, YS Chang. Machining characteristics of titanium alloy (Ti–6Al–4V) using a combination process
of EDM with USM. Journal of Materials Processing Technology. 2000; 104: 171-177.
[5] CH Che Haron, BMd Deros, A Ginting, M Fauziah. Investigation on the influence of machining parameters when
machining tool steel using EDM. Journal of Materials Processing Technology. 2001; 116: 84-87.
[6] CMF Odulio, LG Sison, MT Escoto. Regenerative clamp as reset winding in flyback converters for EDM
applications. in Industrial Technology. IEEE ICIT '04. 2004 IEEE International Conference on. 2004.
[7] CMF Odulio, LG Sison, MT Escoto. Energy-saving Flyback Converter for EDM Applications. TENCON 2005 2005
IEEE Region 10. 2005.
[8] J Yang, S Yi, F Yang, C Jiang, X Wang, F Yang. Fly-back Mode Constant Current LED Driver. Applied Mechanics
and Materials. 2014; 530-531: 1093-1099.
[9] C Basso. Simulations and Practical Designs of Flyback Converter. 2008.
[10] UC3842/3/4/5 Provides Low-Cost Current-Mode Control. 1999, Texas Instruments Incorporated.
BIOGRAPHIES OF AUTHORS
Nazriah Mahmud is a graduate student of Universiti Teknologi Malaysia, Malaysia. She holds
a degree in Biomedical Engineering in 2011. She is currently pursuing her doctorate study in
Biomedical Engineering at Universiti Teknologi Malaysia since September 2011 until now.
Her current research areas include Electrical Discharge Machining (EDM), Power Supply
design and Micro-pitting.
7. IJPEDS ISSN: 2088-8694
Electrical Discharge Machining Flyback Converter using UC3842 Current Mode… (Nazriah Mahmud)
267
Azli Yahya is a senior lecturer in Universiti Teknologi Malaysia since 1998 until now. He
holds a degree in Electro Mechanical Power System and Master’s Degree in Electronic
Production from Glamorgan University, UK. He is a doctorate of Loughborough University,
UK specializing in Electronic and Electrical Engineering. His areas of researches are
Analog/Digital Circuit Design, Electrical Discharge Machining and Power Supply Design.
Trias Andromeda is a lecturer in Diponegoro University, Semarang, Indonesia Since 1999. He
graduated from Gadjah Mada University, Yogyakarta, Indonesia. He holds Degree in control
electronics and Master in electronics signal. He is currently pursuing his doctorate study in
Electrical Engineering at Universiti Teknologi Malaysia since June 2008. His current research
areas include Electrical Discharge Machining (EDM), Power Supply design, artificial
intelligence control and modeling.