In this paper closed loop analysis of Single phase AC-DC Bridgeless Single
Ended Primary Inductance Converter (SEPIC) for Power Factor Correction
(PFC) rectifier is analyzed. In this topology the absence of an input diode
bridge and the due to presence of two semiconductor switches in the current
flowing path during each switching cycle which will results in lesser
conduction losses and improved thermal management compared to the
conventional converters. In this paper the operational principles, Frequency
analysis, and design equations of the proposed converter are described in
detail. Performance of the proposed SEPIC PFC rectifier is carried out using
Matlab Simulink software and results are presented.
A Single-Stage High-Frequency Isolated Secondary- Side Controlled AC-DC Conve...IDES Editor
This paper presents a new single-stage highfrequency
isolated ac-dc converter that uses a simple control
circuit. It is well suitable for wide input variation power
sources. The circuit configuration combines a diode rectifier,
boost converter and half-bridge dc-dc resonant converter. A
high power factor is achieved by discontinuous current mode
(DCM) operation of the front-end integrated power factor
correction circuit. The output voltage is regulated by fixedfrequency,
secondary-side phase-shift active rectifier. Softswitching
operation is achieved for all the switches. This
converter operates in three modes, which is classified
according to conduction of different switches and diodes. The
intervals of operation and steady-state analysis are presented
in detail. Design example of a 100 W proposed converter is
given together with its simulation and experiment results for
wide variation in input voltage.
Simulation of Power Electronic Converter Circuits Using COM3LAB Learning Soft...ijtsrd
Power electronics concepts are difficult to explain using conventional teaching tools. Use of COMB3LAB software in teaching provides additional support forvisual representations of power converter circuits operation and waveforms. Models of different power electronics converters are prepared on COMB3LAB software and generate simulation waveforms. This paper is helpful for the faculty of electrical engineering to find the various applications of COM3LAB software in teaching Khin Myo Aye"Simulation of Power Electronic Converter Circuits Using COM3LAB Learning Software in Teaching: A Case Study" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-2 | Issue-5 , August 2018, URL: http://www.ijtsrd.com/papers/ijtsrd15780.pdf http://www.ijtsrd.com/engineering/electronics-and-communication-engineering/15780/simulation-of-power-electronic-converter-circuits-using-com3lab-learning-software-in-teaching-a-case-study/khin-myo-aye
A bridgeless bhb zvs pwm ac-ac converter for high-frequency induction heating...LeMeniz Infotech
A bridgeless bhb zvs pwm ac-ac converter for high-frequency induction heating applications
Do Your Projects With Technology Experts...
To Get this projects Call : 9566355386 / 99625 88976
Visit : www.lemenizinfotech.com / www.ieeemaster.com
Mail : projects@lemenizinfotech.com
A Single-Stage High-Frequency Isolated Secondary- Side Controlled AC-DC Conve...IDES Editor
This paper presents a new single-stage highfrequency
isolated ac-dc converter that uses a simple control
circuit. It is well suitable for wide input variation power
sources. The circuit configuration combines a diode rectifier,
boost converter and half-bridge dc-dc resonant converter. A
high power factor is achieved by discontinuous current mode
(DCM) operation of the front-end integrated power factor
correction circuit. The output voltage is regulated by fixedfrequency,
secondary-side phase-shift active rectifier. Softswitching
operation is achieved for all the switches. This
converter operates in three modes, which is classified
according to conduction of different switches and diodes. The
intervals of operation and steady-state analysis are presented
in detail. Design example of a 100 W proposed converter is
given together with its simulation and experiment results for
wide variation in input voltage.
Simulation of Power Electronic Converter Circuits Using COM3LAB Learning Soft...ijtsrd
Power electronics concepts are difficult to explain using conventional teaching tools. Use of COMB3LAB software in teaching provides additional support forvisual representations of power converter circuits operation and waveforms. Models of different power electronics converters are prepared on COMB3LAB software and generate simulation waveforms. This paper is helpful for the faculty of electrical engineering to find the various applications of COM3LAB software in teaching Khin Myo Aye"Simulation of Power Electronic Converter Circuits Using COM3LAB Learning Software in Teaching: A Case Study" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-2 | Issue-5 , August 2018, URL: http://www.ijtsrd.com/papers/ijtsrd15780.pdf http://www.ijtsrd.com/engineering/electronics-and-communication-engineering/15780/simulation-of-power-electronic-converter-circuits-using-com3lab-learning-software-in-teaching-a-case-study/khin-myo-aye
A bridgeless bhb zvs pwm ac-ac converter for high-frequency induction heating...LeMeniz Infotech
A bridgeless bhb zvs pwm ac-ac converter for high-frequency induction heating applications
Do Your Projects With Technology Experts...
To Get this projects Call : 9566355386 / 99625 88976
Visit : www.lemenizinfotech.com / www.ieeemaster.com
Mail : projects@lemenizinfotech.com
This is B.E Lab for 3rd Semester Computer Science Branch. Its involve semiconductor CRO and DSO. It consist of 10 experiment which is necessary to perform during semester.
ADCMT Products Selection Guide
Digital Electrometers
System
Digital Multimeters
Optical Measuring Instruments
DC Voltage Current Source/Monitors
Modular & Multifunction Instrument
https://www.n-denkei.com/singapore/inquiry/
IjEVOLUTION OF POWER SUPPLY AND ITS APPLICATION TO ELECTRICAL AND ELECTRONIC ...IAEME Publication
Electricity can be produced using chemical effect where the movement of ions constitutes a flow of current through the electrolyte. Electrochemical cells are used as storage cells where chemical energy can be converted into electrical energy. The most efficient and widely used method for the generation of electricity is based on the laws of Electromagnetic Induction. According to this law electromotive force is induced in a conductor whenever the conductor cuts across magnetic lines of flux. The invention of the Diode Valve in 1904 and the invention of the triode valve in 1906 and their largescale production from 1920 onwards helped to manufacture electronic products and instruments. The invention of the galena-based Cat’s whisker detector in 1906 was the milestone of manufacturing crystal radio receivers. Cuprous oxide rectifier was invented in 1926 and was used for the rectification of power supply frequencies. Selenium rectifier was invented in 1933 and it was also used for the rectification of power frequencies but selenium rectifier was more efficient and was best in low-voltage, heavy current applications. Commercial manufacturing of germanium crystal diode was started in 1946. Then invention of the bipolar junction transistor in 1948 had replaced the valves because of low power, low cost, small size and long-lasting. Electrical products are generally operated from the mains power supply. But electronic products are operated by D.C supply and nowadays most of the communication devices are designed to be operated by the low-watt power supply. Scientists and researchers are developing low power, low heat dissipation, low dropout, miniature and energy harvesting efficient power supply.
Power quality improvement using impedance network based invertereSAT Publishing House
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology.
Three Phase Single Stage Isolated Cuk based PFC ConverterAsoka Technologies
In this paper, analysis and design of a three phase isolated Cuk based power factor correction (PFC) converter has been proposed. The proposed converter is operated in discontinuous output inductor current mode (DOICM) to achieve PFC at ac input. This avoids the inner current control loop which further eliminates the sensing of current. This makes the system more reliable and robust. The converter requires only one simple voltage control loop for output voltage regulation and all the power switches are driven by the same gate signal which simplifies the gate driver circuit. The detailed operation of the converter and design calculations are presented. And also a small signal model of the converter by using CIECE approach is presented to aid the controller design. The experimental results from a 2-kW laboratory prototype with 208-V line-to-line input voltage, 400-V output voltage are presented to confirm the operation of the proposed converter. An input power factor of 0.999, an input current total harmonic distortion of as low as 4.06% and a high conversion efficiency of 95.1% are achieved from laboratory prototype.
42 30 nA Comparative Study of Power Semiconductor Devices for Industrial PWM ...IAES-IJPEDS
The growing demand of energy translates into efficiency requirements of
energy conversion systems and electric drives. Both these systems are based
on Pulse Width Modulation (PWM) Inverter. In this paper we firstly present
the state of art of the main types of semiconductors devices for Industrial
PWM Inverter. In particular we examine the last generations of Silicon
Carbide (SiC) MOSFETs and Insulated Gate Bipolar Transistors (IGBTs)
and we present a comparison between these devices, obtained by SPICE
simulations, both for static characteristics at different temperatures and for
dynamic ones at different gate resistance, in order to identify the one which
makes the PWM inverter more efficient.
Research Inventy : International Journal of Engineering and Science is published by the group of young academic and industrial researchers with 12 Issues per year. It is an online as well as print version open access journal that provides rapid publication (monthly) of articles in all areas of the subject such as: civil, mechanical, chemical, electronic and computer engineering as well as production and information technology. The Journal welcomes the submission of manuscripts that meet the general criteria of significance and scientific excellence. Papers will be published by rapid process within 20 days after acceptance and peer review process takes only 7 days. All articles published in Research Inventy will be peer-reviewed.
Simulation of Bridgeless SEPIC Converter with Modified Switching PulseIJMER
In this paper, a new bridgeless single-ended primary inductance converter(SEPIC) power-factor-correction(PFC) rectifier is introduced. The proposed circuit provides lower conduction losses with reduced components simultaneously. In conventional PFC converters(continuous-conduction-mode boost converter), a voltage loop and a current loop are required for PFC.Simulation is done on bridgeless SEPIC and full bridge SEPIC and found that by working both in DCM conduction losses is less for bridgeless. In the proposed converter, the control circuit is simplified, and no current loop is required while the converter operates in discontinuous conduction mode.
Analysis of a Quasi Resonant Switch Mode Power Supply for Low Voltage Applica...IDES Editor
QRC provides efficient and regulated switch mode
power supplies for robotic and satellite applications. This paper
addresses the enhanced controller techniques for high
frequency isolation based push-pull Quasi Resonant
Converter. This technique is similar to the conventional PI
controller technique but varies only the enhancement
constants to improve the time domain response of the
converter. The proposed converter is designed for low output
voltage and power rating, characteristically 5V and 5 W, with
the comprehension of current design trends towards enhanced
performance. At the primary stage, to validate the design of
the converter, simulation is performed in PSIM for ±50% load
variations. A prototype model of this converter is developed.
The results obtained from the experimental set-up are
presented and analysed in detail. The results reveal the
superiority of the proposed method.
Now day’s the power factor has become a major problem in power system to improve the power quality of the grid, as power factor is affected on the grid due to the nonlinear loads connected to it. Single phase bridgeless AC/DC power factor correction (PFC) topology to improve the power factor as well as the total harmonic distortion (THD) of the utility grid is proposed. By removing the input bridge in conventional PFC converters, the control circuit is simplified; the total harmonics distortion (THD) and power factor (PF) are improved. The PI controller operates in two loops one is the outer control loop which calculates the reference current through LC filter and signal processing. Inner current loop generates PWM switching signals through the PI controller. The output of the proposed PFC topology is verified for prototype using MATLAB circuit simulations. The experimental system is developed, and the simulation results are obtained.
Maximum PowerPoint Tracking of PV System Based on a SEPIC Converter Using Fuz...IJERA Editor
This paper presents the MPPT (Maximum power point tracking) operation of PV (Photovoltaic) system based
on a SEPIC (Single Ended Primary Inverter Converter) converter using fuzzy logic controller. MPPT method
such as Incremental conductance base on FLC (Fuzzy Logic Controller) is used to extract maximum output
power of the PV system. PV energy is the most essential energy resources since it is pollution free, clean and
endless. The FLC proposed scheme is interface with the MPPT to generate the PWM (Pulse Width Modulation)
for the SEPIC controller for maximum power point tracking operation.FLChas used Mamdani’s method for
convergent and divergent of membership function. FLC is used for more efficient performance under the
variation in different atmosphere. The fuzzy logic controller with SEPIC for MPPT scheme extract the
maximum power point tracking without any change in the voltage at the inverter at different load condition. The
behavior of the converter and controller tested in simulation at different operating conditions. Proposed scheme
is used for accurately tracking maximum point and also send the smooth, error free signal to the inverter.
Maximum PowerPoint Tracking of PV System Based on a SEPIC Converter Using Fuz...IJERA Editor
This paper presents the MPPT (Maximum power point tracking) operation of PV (Photovoltaic) system based
on a SEPIC (Single Ended Primary Inverter Converter) converter using fuzzy logic controller. MPPT method
such as Incremental conductance base on FLC (Fuzzy Logic Controller) is used to extract maximum output
power of the PV system. PV energy is the most essential energy resources since it is pollution free, clean and
endless. The FLC proposed scheme is interface with the MPPT to generate the PWM (Pulse Width Modulation)
for the SEPIC controller for maximum power point tracking operation.FLChas used Mamdani’s method for
convergent and divergent of membership function. FLC is used for more efficient performance under the
variation in different atmosphere. The fuzzy logic controller with SEPIC for MPPT scheme extract the
maximum power point tracking without any change in the voltage at the inverter at different load condition. The
behavior of the converter and controller tested in simulation at different operating conditions. Proposed scheme
is used for accurately tracking maximum point and also send the smooth, error free signal to the inverter
Efficient bridgeless SEPIC converter fed PMBLDC motor using artificial neural...IJECEIAES
In this paper, a new design of Bridgeless SEPIC (Single Ended Primary Inductance converter) with Artificial neural network (ANN) fed PMBLDC Motor drive is proposed to improve Power Factor. The proposed converter has single switching device of MOSFET, so the switching losses is reduced.ANN is used to achieve the higher power factor and fixed dc link voltage. Also the ANN methodology the time taken for computation is less since there is no mathematical model. The output voltage depends on the switching frequency of the MOSFET. The BLSEPIC act as a buck operation in continuous conduction mode. Detailed converter analysis, equivalent circuit and closed-loop analysis are presented for 36V, 120W, 1500rpm BLDC Motor drive. This proposed converter produces low conduction loss, low total harmonic reduction, low settling time and high power factor reaching near-unity. All the simulation work is verified with MATLAB – Simulink.
This is B.E Lab for 3rd Semester Computer Science Branch. Its involve semiconductor CRO and DSO. It consist of 10 experiment which is necessary to perform during semester.
ADCMT Products Selection Guide
Digital Electrometers
System
Digital Multimeters
Optical Measuring Instruments
DC Voltage Current Source/Monitors
Modular & Multifunction Instrument
https://www.n-denkei.com/singapore/inquiry/
IjEVOLUTION OF POWER SUPPLY AND ITS APPLICATION TO ELECTRICAL AND ELECTRONIC ...IAEME Publication
Electricity can be produced using chemical effect where the movement of ions constitutes a flow of current through the electrolyte. Electrochemical cells are used as storage cells where chemical energy can be converted into electrical energy. The most efficient and widely used method for the generation of electricity is based on the laws of Electromagnetic Induction. According to this law electromotive force is induced in a conductor whenever the conductor cuts across magnetic lines of flux. The invention of the Diode Valve in 1904 and the invention of the triode valve in 1906 and their largescale production from 1920 onwards helped to manufacture electronic products and instruments. The invention of the galena-based Cat’s whisker detector in 1906 was the milestone of manufacturing crystal radio receivers. Cuprous oxide rectifier was invented in 1926 and was used for the rectification of power supply frequencies. Selenium rectifier was invented in 1933 and it was also used for the rectification of power frequencies but selenium rectifier was more efficient and was best in low-voltage, heavy current applications. Commercial manufacturing of germanium crystal diode was started in 1946. Then invention of the bipolar junction transistor in 1948 had replaced the valves because of low power, low cost, small size and long-lasting. Electrical products are generally operated from the mains power supply. But electronic products are operated by D.C supply and nowadays most of the communication devices are designed to be operated by the low-watt power supply. Scientists and researchers are developing low power, low heat dissipation, low dropout, miniature and energy harvesting efficient power supply.
Power quality improvement using impedance network based invertereSAT Publishing House
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology.
Three Phase Single Stage Isolated Cuk based PFC ConverterAsoka Technologies
In this paper, analysis and design of a three phase isolated Cuk based power factor correction (PFC) converter has been proposed. The proposed converter is operated in discontinuous output inductor current mode (DOICM) to achieve PFC at ac input. This avoids the inner current control loop which further eliminates the sensing of current. This makes the system more reliable and robust. The converter requires only one simple voltage control loop for output voltage regulation and all the power switches are driven by the same gate signal which simplifies the gate driver circuit. The detailed operation of the converter and design calculations are presented. And also a small signal model of the converter by using CIECE approach is presented to aid the controller design. The experimental results from a 2-kW laboratory prototype with 208-V line-to-line input voltage, 400-V output voltage are presented to confirm the operation of the proposed converter. An input power factor of 0.999, an input current total harmonic distortion of as low as 4.06% and a high conversion efficiency of 95.1% are achieved from laboratory prototype.
42 30 nA Comparative Study of Power Semiconductor Devices for Industrial PWM ...IAES-IJPEDS
The growing demand of energy translates into efficiency requirements of
energy conversion systems and electric drives. Both these systems are based
on Pulse Width Modulation (PWM) Inverter. In this paper we firstly present
the state of art of the main types of semiconductors devices for Industrial
PWM Inverter. In particular we examine the last generations of Silicon
Carbide (SiC) MOSFETs and Insulated Gate Bipolar Transistors (IGBTs)
and we present a comparison between these devices, obtained by SPICE
simulations, both for static characteristics at different temperatures and for
dynamic ones at different gate resistance, in order to identify the one which
makes the PWM inverter more efficient.
Research Inventy : International Journal of Engineering and Science is published by the group of young academic and industrial researchers with 12 Issues per year. It is an online as well as print version open access journal that provides rapid publication (monthly) of articles in all areas of the subject such as: civil, mechanical, chemical, electronic and computer engineering as well as production and information technology. The Journal welcomes the submission of manuscripts that meet the general criteria of significance and scientific excellence. Papers will be published by rapid process within 20 days after acceptance and peer review process takes only 7 days. All articles published in Research Inventy will be peer-reviewed.
Simulation of Bridgeless SEPIC Converter with Modified Switching PulseIJMER
In this paper, a new bridgeless single-ended primary inductance converter(SEPIC) power-factor-correction(PFC) rectifier is introduced. The proposed circuit provides lower conduction losses with reduced components simultaneously. In conventional PFC converters(continuous-conduction-mode boost converter), a voltage loop and a current loop are required for PFC.Simulation is done on bridgeless SEPIC and full bridge SEPIC and found that by working both in DCM conduction losses is less for bridgeless. In the proposed converter, the control circuit is simplified, and no current loop is required while the converter operates in discontinuous conduction mode.
Analysis of a Quasi Resonant Switch Mode Power Supply for Low Voltage Applica...IDES Editor
QRC provides efficient and regulated switch mode
power supplies for robotic and satellite applications. This paper
addresses the enhanced controller techniques for high
frequency isolation based push-pull Quasi Resonant
Converter. This technique is similar to the conventional PI
controller technique but varies only the enhancement
constants to improve the time domain response of the
converter. The proposed converter is designed for low output
voltage and power rating, characteristically 5V and 5 W, with
the comprehension of current design trends towards enhanced
performance. At the primary stage, to validate the design of
the converter, simulation is performed in PSIM for ±50% load
variations. A prototype model of this converter is developed.
The results obtained from the experimental set-up are
presented and analysed in detail. The results reveal the
superiority of the proposed method.
Now day’s the power factor has become a major problem in power system to improve the power quality of the grid, as power factor is affected on the grid due to the nonlinear loads connected to it. Single phase bridgeless AC/DC power factor correction (PFC) topology to improve the power factor as well as the total harmonic distortion (THD) of the utility grid is proposed. By removing the input bridge in conventional PFC converters, the control circuit is simplified; the total harmonics distortion (THD) and power factor (PF) are improved. The PI controller operates in two loops one is the outer control loop which calculates the reference current through LC filter and signal processing. Inner current loop generates PWM switching signals through the PI controller. The output of the proposed PFC topology is verified for prototype using MATLAB circuit simulations. The experimental system is developed, and the simulation results are obtained.
Maximum PowerPoint Tracking of PV System Based on a SEPIC Converter Using Fuz...IJERA Editor
This paper presents the MPPT (Maximum power point tracking) operation of PV (Photovoltaic) system based
on a SEPIC (Single Ended Primary Inverter Converter) converter using fuzzy logic controller. MPPT method
such as Incremental conductance base on FLC (Fuzzy Logic Controller) is used to extract maximum output
power of the PV system. PV energy is the most essential energy resources since it is pollution free, clean and
endless. The FLC proposed scheme is interface with the MPPT to generate the PWM (Pulse Width Modulation)
for the SEPIC controller for maximum power point tracking operation.FLChas used Mamdani’s method for
convergent and divergent of membership function. FLC is used for more efficient performance under the
variation in different atmosphere. The fuzzy logic controller with SEPIC for MPPT scheme extract the
maximum power point tracking without any change in the voltage at the inverter at different load condition. The
behavior of the converter and controller tested in simulation at different operating conditions. Proposed scheme
is used for accurately tracking maximum point and also send the smooth, error free signal to the inverter.
Maximum PowerPoint Tracking of PV System Based on a SEPIC Converter Using Fuz...IJERA Editor
This paper presents the MPPT (Maximum power point tracking) operation of PV (Photovoltaic) system based
on a SEPIC (Single Ended Primary Inverter Converter) converter using fuzzy logic controller. MPPT method
such as Incremental conductance base on FLC (Fuzzy Logic Controller) is used to extract maximum output
power of the PV system. PV energy is the most essential energy resources since it is pollution free, clean and
endless. The FLC proposed scheme is interface with the MPPT to generate the PWM (Pulse Width Modulation)
for the SEPIC controller for maximum power point tracking operation.FLChas used Mamdani’s method for
convergent and divergent of membership function. FLC is used for more efficient performance under the
variation in different atmosphere. The fuzzy logic controller with SEPIC for MPPT scheme extract the
maximum power point tracking without any change in the voltage at the inverter at different load condition. The
behavior of the converter and controller tested in simulation at different operating conditions. Proposed scheme
is used for accurately tracking maximum point and also send the smooth, error free signal to the inverter
Efficient bridgeless SEPIC converter fed PMBLDC motor using artificial neural...IJECEIAES
In this paper, a new design of Bridgeless SEPIC (Single Ended Primary Inductance converter) with Artificial neural network (ANN) fed PMBLDC Motor drive is proposed to improve Power Factor. The proposed converter has single switching device of MOSFET, so the switching losses is reduced.ANN is used to achieve the higher power factor and fixed dc link voltage. Also the ANN methodology the time taken for computation is less since there is no mathematical model. The output voltage depends on the switching frequency of the MOSFET. The BLSEPIC act as a buck operation in continuous conduction mode. Detailed converter analysis, equivalent circuit and closed-loop analysis are presented for 36V, 120W, 1500rpm BLDC Motor drive. This proposed converter produces low conduction loss, low total harmonic reduction, low settling time and high power factor reaching near-unity. All the simulation work is verified with MATLAB – Simulink.
International Journal of Engineering Research and Development (IJERD)IJERD Editor
journal publishing, how to publish research paper, Call For research paper, international journal, publishing a paper, IJERD, journal of science and technology, how to get a research paper published, publishing a paper, publishing of journal, publishing of research paper, reserach and review articles, IJERD Journal, How to publish your research paper, publish research paper, open access engineering journal, Engineering journal, Mathemetics journal, Physics journal, Chemistry journal, Computer Engineering, Computer Science journal, how to submit your paper, peer reviw journal, indexed journal, reserach and review articles, engineering journal, www.ijerd.com, research journals,
yahoo journals, bing journals, International Journal of Engineering Research and Development, google journals, hard copy of journal
International Journal of Engineering Research and Development (IJERD)IJERD Editor
journal publishing, how to publish research paper, Call For research paper, international journal, publishing a paper, IJERD, journal of science and technology, how to get a research paper published, publishing a paper, publishing of journal, publishing of research paper, reserach and review articles, IJERD Journal, How to publish your research paper, publish research paper, open access engineering journal, Engineering journal, Mathemetics journal, Physics journal, Chemistry journal, Computer Engineering, Computer Science journal, how to submit your paper, peer reviw journal, indexed journal, reserach and review articles, engineering journal, www.ijerd.com, research journals,
yahoo journals, bing journals, International Journal of Engineering Research and Development, google journals, hard copy of journal,
Electrical Discharge Machining Flyback Converter using UC3842 Current Mode PW...IJPEDS-IAES
This paper presents a current mode Pulse Width Modulation (PWM) controlled Flyback converter using UC3842 for Electrical Discharge Machining current generator control circuit. Circuit simplicity and high efficiency can be achieved by a Flyback converter with current mode PWM controller. The behaviors of the system's operation is analyzed and discussed by varying the load resistance. Matlab sofware is used to simulate the Flyback converter where a prototype has been built and tested to verify its performance.
Transformer Less Voltage Quadrupler Based DC-DC Converter with Coupled Induct...IJPEDS-IAES
In this paper a voltage quadrupler dc-dc converter with coupled inductor
and π filter is presented. The use of the coupled inductor reduces the high
leakage inductance which is present in a transformer enabled converter.
The output ripples in the converter is reduced by providing a π filter.
The interleaved voltage quadrupler is used in this system in order to boost the
output voltage. The voltage multiplier improves the output voltage gain.
The main advantage of this system is more voltage gain when compared with
the transformer eneabled circuit and the overall efficiency of the system is
improved. The circuit is simple to control. As a final point of this research,
the simulation and the hardware investigational results are presented to
demonstrate the effectiveness of this proposed converter.
This manuscript deals with the simulation of AC - DC Zeta converter for high power drive application with greater efficiency, lesser losses and power factor correction. It involves simpler control circuitry with less external components. The explanation of Fundamental function of Zeta converter is given in this paper. To condense the harmonic content the PI, PID and Fuzzy Logic controller are used. The operation of Zeta converter in open loop, closed loop is obtained. Closed loop system of zeta converter proves better performance over open loop system. Open and closed loop circuits are simulated by using MATLAB simulink. By giving disturbance in closed loop and open loop systems, feat of Zeta converter is compared.
This paper presents the improved single phase AC-DC super lift Luo converter for enhancing quality of power by mitigating the issues. The proposed converter is used for output voltage control, power factor improvement and reduced source current harmonics at supply side. The main intention of this work is to design appropriate closed loop controllers for this AC-DC super lift Luo converter to achieve unity power factor in the source end. The designed control system comprises of two control loops, voltage control in outer loop and the current controller is devised in the inner loop. Fuzzy controller is used for current controller whereas PI controller as voltage controller. In the MATLAB/SIMULINK platform, simulation of the proposed AC-DC super lift Luo converter is done. It is clear from the simulation results that PI integrated fuzzy controller for voltage and control is proven to be better than classical PI with hysteresis controllers. The proposed system is able to achieve high input power factor along with supply current harmonic distortions of less than 5%.
The International Journal of Engineering & Science is aimed at providing a platform for researchers, engineers, scientists, or educators to publish their original research results, to exchange new ideas, to disseminate information in innovative designs, engineering experiences and technological skills. It is also the Journal's objective to promote engineering and technology education. All papers submitted to the Journal will be blind peer-reviewed. Only original articles will be published.
The papers for publication in The International Journal of Engineering& Science are selected through rigorous peer reviews to ensure originality, timeliness, relevance, and readability.
Comparison of PI and PID Controlled Bidirectional DC-DC Converter SystemsIJPEDS-IAES
This paper deals with comparison of responses of the PI and the PID
controlled bidirectional DC-DC converter systems. A coupled inductor is
used in the present work to produce high gain. Open loop and closed loop
controlled systems with PI and PID controllers are designed and simulated
using Matlab tool. The principles of operation and simulation case studies are
discussed in detail. The comparison is made in terms of rise time, fall time,
peak overshoot and steady state error.
Implementation of Buck-Boost Converter as Low Voltage Stabilizer at 15 VIJECEIAES
This paper presents the implementation of the buck-boost converter design which is a power electronics applications that can stabilize voltage, even though the input voltage changes. Regulator to stabilize the voltage using PWM pulse that triger pin 2 on XL6009. In this design of buck-boost converter is implemented using the XL6009, LM7815 and TIP2955. LM7815 as output voltage regulator at 15V with 1A output current, while TIP2955 is able to overcome output current up to 5A. When the LM7815 and TIP2955 are connected in parallel, the converter can increase the output current to 6A.. Testing is done using varied voltage sources that can be set. The results obtained from this design can be applied to PV (Photovoltaic) and WP (Wind Power), with changes in input voltage between 3-21V dc can produce output voltage 15V.
Phase-Shifted Full-Bridge Zero Voltage Switching DC-DC Converter Design with ...IJECEIAES
Design of phase-shifted full bridge zero voltage switching DC-DC converter has been very challenging due to circuit parasitic effect on the system dynamics. This paper presents steady-state analysis and iterative approach for the systemic design of phase-shifted full bridge DC-DC converter with improved dynamic performance and satisfactory operational requirement in terms of zero-voltage switching range, operating switching frequency and switching resonance. A 3 kW DC-DC converter is designed using the iterative design approach and the system dynamics performance was investigated in the MATLAB/Simulink environment. The converter zerovoltage switching simulation results were satisfactory with 90% efficiency under full load condition.
A Low Cost Single-Switch Bridgeless Boost PFC ConverterIJPEDS-IAES
This paper proposes the single-switch bridgeless boost power factor correction (PFC) converter to achieve high efficiency in low cost. The proposed converter utilizes only one active switching device forPFC operation as well as expecting higher efficiency than typical boost PFC converters. On the other hand, the implementation cost is less than traditional bridgeless boost PFC converters, in where two active switching deivces are necessary. The operational principle, the modeling, and the control scheme of the proposed converter arediscussed in detail. In order to verify the operation of the proposed converter, a 500W switching model is built in PSIM software package. The simulation results show that the proposed converter perfectly achieves PFC operation with only a single active switch.
Similar to Closed Loop Analysis of Bridgeless SEPIC Converter for Drive Application (20)
Inter-Area Oscillation Damping using an STATCOM Based Hybrid Shunt Compensati...IJPEDS-IAES
FACTS devices are one of the latest technologies which have been used to
improve power system dynamic and stability during recent years. However,
widespread adoption of this technology has been hampered by high cost
and reliability concerns. In this paper an economical phase imbalanced shunt
reactive compensation concept has been introduced and its ability for power
system dynamic enhancement and inter-area oscillation damping are
investigated. A hybrid phase imbalanced scheme is a shunt capacitive
compensation scheme, where two phases are compensated by fixed shunt
capacitor (C) and the third phase is compensated by a Static Synchronous
Compensator (STATCOM) in shunt with a fixed capacitor (CC). The power
system dynamic stability enhancement would be achieved by adding
a conventional Wide Area Damping Controller (WADC) to the main control
loop of the single phase STATCOM. Two different control methodologies
are proposed: a non-optimized conventional damping controller
and a conventional damping controller with optomised parameters that are
added to the main control loop of the unbalanced compensator in order to
damp the inter area oscillations. The proposed arrangement would, certainly,
be economically attractive when compared with a full three-phase
STATCOM. The proposed scheme is prosperously applied in a 13-bus
six-machine test system and various case studies are conducted to
demonstrate its ability in damping inter-area oscillations and power system
dynamic enhancement.
Fuzzy Gain-Scheduling Proportional–Integral Control for Improving the Speed B...IJPEDS-IAES
In this article, we have set up a vector control law of induction machine
where we tried different type of speed controllers. Our control strategy is of
type Field Orientated Control (FOC). In this structure we designed a Fuzzy
Gain-Scheduling Proportional–Integral (Pi) controller to obtain best result
regarding the speed of induction machine. At the beginning we designed a Pi
controller with fixed parameters. We came up to these parameters by
identifying the transfer function of this controller to that of Broïda (second
order transfer function). Then we designed a fuzzy logic (FL) controller.
Based on simulation results, we highlight the performances of each
controller. To improve the speed behaviour of the induction machine, we
have designend a controller called “Fuzzy Gain-Scheduling Proportional–
Integral controller” (FGS-PI controller) which inherited the pros of the
aforementioned controllers. The simulation result of this controller will
strengthen its performances.
Advance Technology in Application of Four Leg Inverters to UPQCIJPEDS-IAES
This article presents a novel application of four leg inverter with
conventional Sinusoidal Pulse Width Modulation (SPWM) Scheme to
Unified Power Quality Conditioner (UPQC). The Power Quality problem
became burning issues since the starting of high voltage AC transmission
system. Hence, in this article it has been discussed to mitigate the PQ issues
in high voltage AC systems through a three phase Unified Power Quality
Conditioner (UPQC) under various conditions, such as harmonic mitigation
scheme, non linear loads, sag and swell conditions as well. Also, it proposes
to control harmoincs with various artificial intelligent techniques. Thus
application of these control technique such as Neural Networks (ANN)
Fuzzy Logic makes the system performance in par with the standards
and also compared with existing system. The simulation results based on
MATLAB/Simulink are discussed in detail to support the concept developed
in the paper.
Modified SVPWM Algorithm for 3-Level Inverter Fed DTC Induction Motor DriveIJPEDS-IAES
In this paper, a modified space vector pulse width modulation (MSVPWM)
algorithm is developed for 3-level inverter fed direct torque controlled
induction motor drive (DTC-IMD). MSVPWM algorithm simplifies
conventional space vector pulse width modulation (CSVPWM) algorithm for
multilevel inverter (MLI), whose complexity lies in sector/subsector/subsubsector
identification; which will commensurate with number of levels. In
the proposed algorithm sectors are identified as in two level inverter
and subsectors/sub-subsectors are identified by shifting the original reference
vector to sector 1 (S1). This is valid due to the fact that a three level space
vector plane is a composition of six two level space planes, and are
symmetrical with reference to six pivot states. Switching state/sequence
selection is also very important while dealing with SVPWM strategy for
MLI. In the proposed algorithm out of 27 available switching states apt
switching state is selected based on sector and subsector number, such that
voltage ripple is considerably less. To validate the proposed algorithm, it is
tested on a three level neutral point clamped (NPC) inverter fed DTC-IMD.
The performance of the MSVPWM algorithm is analyzed by comparing no
load stator current ripple of the three level DTC-IMD with two level
DTC-IMD. Significant reduction in steady state torque and flux ripple is
observed. Hence, reduced acoustic noise is a distinctive facet of the proposed
method.
Modelling of a 3-Phase Induction Motor under Open-Phase Fault Using Matlab/Si...IJPEDS-IAES
The d-q model of Induction Motors (IMs) has been effectively used as an
efficient method to analyze the performance of the induction machines. This
study presents a step by step Matlab/Simulink implementation
of a star-connected 3-phase IM under open-phase fault (faulty 3-phase IM)
using d-q model. The presented technique in this paper can be simply
implemented in one block and can be made available for control purposes.
The simulated results provide to show the behavior of the star-connected 3-phase IM under open-phase fault condition.
Performance Characteristics of Induction Motor with FielIJPEDS-IAES
With development of power electronics and control Theories, the AC motor
control becomes easier. So the AC motors are used instead of the DC motor
in the drive applications. With this development, a several methods of control
are invented. The field oriented control and direct torque control are from the
best methods to control the drive systems. This paper is compared between
the field oriented control and direct torque control to show the advantages
and disadvantages of these methods of controls. This study discussed the
effects of these methods of control on the total harmonic distortion of the
current and torque ripples. This occurs through study the performance
characteristics of the AC motor. The motor used in this study is an induction
motor. This study is simulated through the MATLAB program.
A Novel Modified Turn-on Angle Control Scheme for Torque- Ripple Reduction in...IJPEDS-IAES
In recent years, Switched Reluctance Motors (SRM) have been dramatically
considered with both researchers and industries. SRMs not only have a
simple and reliable structure, but also have low cost production process.
However, discrete torque production of SRM along with intensive magnetic
saturation in stator and rotor cores are the major drawbacks of utilizing in
variety of industrial applications and also causes the inappropriate torque
ripples. In this paper, a modified logical-rule-based Torque Sharing Function
(TSF) method is proposed considering turn-on angle control. The optimized
turn-on angle for conducting each phase is achieved by estimating the
inductance curve in the vicinity of unaligned position and based on an
analytical solution for each phase voltage equation. Simulation results on a
four-phase switched reluctance motor and comparison with the conventional
methods validates the effectiveness of the proposed method.
Modeling and Simulation of Induction Motor based on Finite Element AnalysisIJPEDS-IAES
This paper presents the development of a co-simulation platform of induction
motor (IM). For the simulation, a coupled model is introduced which
contains the control, the power electronics and also the induction machine.
Each of these components is simulated in different software environments.
So, this study provides an advanced modeling and simulation tools for IM
which integrate all the components into one common simulation platform
environment. In this work, the IM is created using Ansys-Maxwell based on
Finite Element Analysis (FEA), whereas the power electronic converter is
developed in Ansys-Simplorer and the control scheme is build in MATLABSimulink
environment. Such structure can be useful for accurate design
and allows coupling analysis for more realistic simulation. This platform is
exploited to analyze the system models with faults caused by failures of
different drive’s components. Here, two studies cases are presented: the first
is the effects of a faulty device of the PWM inverter, and the second case is
the influence of the short circuit of two stator phases. In order to study the
performance of the control drive of the IM under fault conditions,
a co-simulation of the global dynamic model has been proposed to analyze
the IM behavior and control drives. In this work, the co-simulation has been
performed; furthermore the simulation results of scalar control allowed
verifying the precision of the proposed FEM platform.
Comparative Performance Study for Closed Loop Operation of an Adjustable Spee...IJPEDS-IAES
In this paper an extensive comparative study is carried out between PI
and PID controlled closed loop model of an adjustable speed Permanent
Magnet Synchronous Motor (PMSM) drive. The incorporation of Sinusoidal
Pulse Width Modulation (SPWM) strategy establishes near sinusoidal
armature phase currents and comparatively less torque ripples without
sacrificing torque/weight ratio. In this closed loop model of PMSM drive, the
information about reference speed is provided to a speed controller, to ensure
that actual drive speed tracks the reference speed with ideally zero steady
state speed error. The entire model of PMSM closed loop drive is divided
into two loops, inner loop current and outer loop speed. By taking the
different combinations of two classical controllers (PI & PID) related with
two loop control structure, different approximations are carried out. Hence a
typical comparative study is introduced to familiar with the different
performance indices of the system corresponding to time domain and
frequency domain specifications. Therefore overall performance of closed
loop PMSM drive is tested and effectiveness of controllers will be
determined for different combinations.
Novel Discrete Components Based Speed Controller for Induction MotorIJPEDS-IAES
This paper presents an electronic design based on general purpose discrete
components for speed control of a single phase induction motor drive. The
MOSFETs inverter switching is controlled using Sampled Sinusoidal Pulse
Width Modulation (SPWM) techniques with V/F method based on Voltage
Controlled Oscillator (VCO). The load power is also controlled by a novel
design to produce a suitable SPWM pulse. The proposed electronic system
has ability to control the output frequency with flexible setting of lower limit
to less than 1 Hz and to higher frequency limits to 55 Hz. Moreover, the
proposed controller able to control the value of load voltage to frequency
ratio, which plays a major parameter in the function of IM speed control.
Furthermore, the designed system is characterized by easy manufacturing
and maintenance, high speed response, low cost, and does not need to
program steps as compared to other systems based on Microcontroller
and digital signal processor (DSP) units. The complete proposed electronic
design is made by the software of NI Multisim version 11.0 and all the
internal sub-designs are shown in this paper. Simulation results show the
effectiveness of electronic design for a promising of a high performance IM
PWM drive.
Sensorless Control of a Fault Tolerant PMSM Drives in Case of Single-Phase Op...IJPEDS-IAES
This paper introduces a sensorless-speed-controlled PMSM motor fed by a
four-leg inverter in case of a single phase open circuit fault regardless in
which phase is the fault. To minimize the system performance degradation
due to a single phase open circuit fault, a fault tolerant control strategy that
includes taking appropriate actions to control the two remaining healthy
currents is used in addition to use the fourth leg of the inverter. Tracking the
saliency is done through measuring the dynamic current responses of the
healthy phases of the PMSM motor due the IGBT switching actions using the
fundamental PWM method without introducing any modification to the
operation of the fourth leg of the inverter. Simulation results are provided to
verify the effectiveness of the proposed strategy for sensorless controlling of
a PMSM motor driven by a fault-tolerant four-phase inverter over a wide
speed ranges under the case of a single phase open circuit.
Improved Stator Flux Estimation for Direct Torque Control of Induction Motor ...IJPEDS-IAES
Stator flux estimation using voltage model is basically the integration of the
induced stator back electromotive force (emf) signal. In practical
implementation the pure integration is replaced by a low pass filter to avoid
the DC drift and saturation problems at the integrator output because of the
initial condition error and the inevitable DC components in the back emf
signal. However, the low pass filter introduces errors in the estimated stator
flux which are significant at frequencies near or lower than the cutoff
frequency. Also the DC components in the back emf signal are amplified at
the low pass filter output by a factor equals to . Therefore, different
integration algorithms have been proposed to improve the stator flux
estimation at steady state and transient conditions. In this paper a new
algorithm for stator flux estimation is proposed for direct torque control
(DTC) of induction motor drives. The proposed algorithm is composed of a
second order high pass filter and an integrator which can effectively
eliminates the effect of the error initial condition and the DC components.
The amplitude and phase errors compensation algorithm is selected such that
the steady state frequency response amplitude and phase angle are equivalent
to that of the pure integrator and the multiplication and division by stator
frequency are avoided. Also the cutoff frequency selection is improved; even
small value can filter out the DC components in the back emf signal. The
simulation results show the improved performance of the induction motor
direct torque control drive with the proposed stator flux estimation algorithm.
The simulation results are verified by the experimental results.
Minimization of Starting Energy Loss of Three Phase Induction Motors Based on...IJPEDS-IAES
The purpose of this paper is to minimize energy losses consumed by three
phase induction motors during starting with wide range of load torque from
no load to full load. This will limit the temperature rise and allows for more
numbers of starting during a definite time. Starting energy losses
minimization is achieved by controlling the rate of increasing voltage
and frequency to start induction motor under certain load torque within a
definite starting time. Optimal voltage and frequency are obtained by particle
swarm optimization (PSO) tool according to load torque. Then, outputs of the
PSO are used to design a neuro-fuzzy controller to control the output voltage
and frequency of the inverter during starting for each load torque. The
starting characteristics using proposed method are compared to that of direct
on line and V/F methods. A complete model of the system is developed using
SIMULINK/MATLAB.
Hardware Implementation of Solar Based Boost to SEPIC Converter Fed Nine Leve...IJPEDS-IAES
Multi level inverters are widely used in high power applications because of
low harmonic distortion. This paper deals with the simulation
and implementation of PV based boost to SEPIC converter with multilevel
inverter. The output of PV system is stepped up using boost to sepic
converter and it is converted into AC using a multilevel inverter.
The simulation and experimental results with the R load is presented in this
paper. The FFT analysis is done and the THD values are compared. Boost to
SEPIC converter is proposed to step up the voltage to the required value. The
experimental results are compared with the simulation results. The results
indicate that nine level inverter system has better performance than seven
level inverter system.
IRAMY Inverter Control for Solar Electric VehicleIJPEDS-IAES
Solar Electric Vehicles (SEV) are considered the future vehicles to solve the issues of air pollution, global warming, and the rapid decreases of the petroleum resources facing the current transportation technology. However, SEV are still facing important technical obstacles to overcome. They include batteries energy storage capacity, charging times, efficiency of the solar panels and electrical propulsion systems. Solving any of those problems and electric vehicles will compete-complement the internal combustion engines vehicles. In the present work, we propose an electrical propulsion system based on three phase induction motor in order to obtain the desired speed and torque with less power loss. Because of the need to lightweight nature, small volume, low cost, less maintenance and high efficiency system, a three phase squirrel cage induction motor (IM) is selected in the electrical propulsion system. The IM is fed from three phase inverter operated by a constant V/F control method and Space Vector Pulse Width Modulation (SVPWM) algorithm. The proposed control strategy has been implemented on the texas instruments TM320F2812 Digital Signal Processor (DSP) to generate SVPWM signal needed to trigger the gates of IGBT based inverter. The inverter used in this work is a three phase inverter IRAMY20UP60B type. The experimental results show the ability of the proposed control strategy to generate a three-phase sine wave signal with desired frequency. The proposed control strategy is experimented on a locally manufactured EV prototype. The results show that the EV prototype can be propelled to speed up to 60km/h under different road conditions.
Design and Implementation of Single Phase AC-DC Buck-Boost Converter for Powe...IJPEDS-IAES
This paper discusses the Power Factor Correction (PFC) for single phase AC-DC Buck-Boost Converter (BBC) operated in Continuous Conduction Mode (CCM) using inductor average current mode control. The proposed control technique employs Proportional-Integral (PI) controller in the outer voltage loop and the Inductor Average Current Mode Control (IACMC) in the inner current loop for PFC BBC. The IACMC has advantages such as robustness when there are large variations in line voltage and output load. The PI controller is developed by using state space average model of BBC. The simulation of the proposed system with its control circuit is implemented in MatLab/Simulink. The simulation results show a nearly unity power factor can be attained and there is almost no change in power factor when the line frequency is at various ranges. Experimental results are provided to show its validity and feasibility.
Improvement of Wind farm with PMSG using STATCOMIJPEDS-IAES
This paper studies about the dynamic performance of the Permanent Magnet Synchronous Generator with Static Synchronous Compensator (STATCOM) for Wind farm integration. A whole dynamic model of wind energy conversion system (WECS) with PMSG and STATCOM are established in a MATLAB environment. With this model the dynamic behaviour of the generator and the overall system has been studied to determine the performance of them with and without STATCOM. Final results portrays that the WECS based PMSG with STATCOM improves the transient response of the wind farm when the system is in fault.
Modeling and Control of a Doubly-Fed Induction Generator for Wind Turbine-Gen...IJPEDS-IAES
This paper presents a vector control direct (FOC) of double fed induction generator intended to control the generated stator powers. This device is intended to be implemented in a variable-speed wind-energy conversion system connected to the grid. In order to control the active and reactive power exchanged between the machine stator and the grid, the rotor is fed by a bi-directional converter. The DFIG is controlled by standard relay controllers. Details of the control strategy and system simulation were performed using Simulink and the results are presented in this here to show the effectiveness of the proposed control strategy.
A Review on Design and Development of high Reliable Hybrid Energy Systems wit...IJPEDS-IAES
Hybrid Energy system is a combination of two or more different types of energy resources. Now a day this hybrid energy system plays key role in various remote area power applications. Hybrid energy system is more reliable than single energy system. This paper deals with high reliable hybrid energy system with solar, wind and micro hydro resources. The proposed hybrid system cable of multi mode operation and high reliable due to non communicated based controllers (Droop Characteristic Control) are used for optimal power sharing. Size of battery can be reduced because hydro used as back up source and Maximum power point Tracking also applied to solar and wind energy systems.
Fuzzy Sliding Mode Control for Photovoltaic SystemIJPEDS-IAES
In this study, a fuzzy sliding mode control (FSMC) based maximum power point tracking strategy has been applied for photovoltaic (PV) system. The key idea of the proposed technique is to combine the performances of the fuzzy logic and the sliding mode control in order to improve the generated power for a given set of climatic conditions. Different from traditional sliding mode control, the developed FSMC integrates two parts. The first part uses a fuzzy logic controller with two inputs and 25 rules as an equivalent controller while the second part is designed for an online adjusting of the switching controller’s gain using a fuzzy tuner with one input and one output. Simulation results showed the effectiveness of the proposed approach achieving maximum power point. The fuzzy sliding mode (FSM) controller takes less time to track the maximum power point, reduced the oscillation around the operating point and also removed the chattering phenomena that could lead to decrease the efficiency of the photovoltaic system.
Saudi Arabia stands as a titan in the global energy landscape, renowned for its abundant oil and gas resources. It's the largest exporter of petroleum and holds some of the world's most significant reserves. Let's delve into the top 10 oil and gas projects shaping Saudi Arabia's energy future in 2024.
TECHNICAL TRAINING MANUAL GENERAL FAMILIARIZATION COURSEDuvanRamosGarzon1
AIRCRAFT GENERAL
The Single Aisle is the most advanced family aircraft in service today, with fly-by-wire flight controls.
The A318, A319, A320 and A321 are twin-engine subsonic medium range aircraft.
The family offers a choice of engines
About
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.
Technical Specifications
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
Key Features
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface
• Compatible with MAFI CCR system
• Copatiable with IDM8000 CCR
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
Application
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.
Industrial Training at Shahjalal Fertilizer Company Limited (SFCL)MdTanvirMahtab2
This presentation is about the working procedure of Shahjalal Fertilizer Company Limited (SFCL). A Govt. owned Company of Bangladesh Chemical Industries Corporation under Ministry of Industries.
Sachpazis:Terzaghi Bearing Capacity Estimation in simple terms with Calculati...Dr.Costas Sachpazis
Terzaghi's soil bearing capacity theory, developed by Karl Terzaghi, is a fundamental principle in geotechnical engineering used to determine the bearing capacity of shallow foundations. This theory provides a method to calculate the ultimate bearing capacity of soil, which is the maximum load per unit area that the soil can support without undergoing shear failure. The Calculation HTML Code included.
Water scarcity is the lack of fresh water resources to meet the standard water demand. There are two type of water scarcity. One is physical. The other is economic water scarcity.
Forklift Classes Overview by Intella PartsIntella Parts
Discover the different forklift classes and their specific applications. Learn how to choose the right forklift for your needs to ensure safety, efficiency, and compliance in your operations.
For more technical information, visit our website https://intellaparts.com
CFD Simulation of By-pass Flow in a HRSG module by R&R Consult.pptxR&R Consult
CFD analysis is incredibly effective at solving mysteries and improving the performance of complex systems!
Here's a great example: At a large natural gas-fired power plant, where they use waste heat to generate steam and energy, they were puzzled that their boiler wasn't producing as much steam as expected.
R&R and Tetra Engineering Group Inc. were asked to solve the issue with reduced steam production.
An inspection had shown that a significant amount of hot flue gas was bypassing the boiler tubes, where the heat was supposed to be transferred.
R&R Consult conducted a CFD analysis, which revealed that 6.3% of the flue gas was bypassing the boiler tubes without transferring heat. The analysis also showed that the flue gas was instead being directed along the sides of the boiler and between the modules that were supposed to capture the heat. This was the cause of the reduced performance.
Based on our results, Tetra Engineering installed covering plates to reduce the bypass flow. This improved the boiler's performance and increased electricity production.
It is always satisfying when we can help solve complex challenges like this. Do your systems also need a check-up or optimization? Give us a call!
Work done in cooperation with James Malloy and David Moelling from Tetra Engineering.
More examples of our work https://www.r-r-consult.dk/en/cases-en/
Student information management system project report ii.pdfKamal Acharya
Our project explains about the student management. This project mainly explains the various actions related to student details. This project shows some ease in adding, editing and deleting the student details. It also provides a less time consuming process for viewing, adding, editing and deleting the marks of the students.
Final project report on grocery store management system..pdfKamal Acharya
In today’s fast-changing business environment, it’s extremely important to be able to respond to client needs in the most effective and timely manner. If your customers wish to see your business online and have instant access to your products or services.
Online Grocery Store is an e-commerce website, which retails various grocery products. This project allows viewing various products available enables registered users to purchase desired products instantly using Paytm, UPI payment processor (Instant Pay) and also can place order by using Cash on Delivery (Pay Later) option. This project provides an easy access to Administrators and Managers to view orders placed using Pay Later and Instant Pay options.
In order to develop an e-commerce website, a number of Technologies must be studied and understood. These include multi-tiered architecture, server and client-side scripting techniques, implementation technologies, programming language (such as PHP, HTML, CSS, JavaScript) and MySQL relational databases. This is a project with the objective to develop a basic website where a consumer is provided with a shopping cart website and also to know about the technologies used to develop such a website.
This document will discuss each of the underlying technologies to create and implement an e- commerce website.
Quality defects in TMT Bars, Possible causes and Potential Solutions.PrashantGoswami42
Maintaining high-quality standards in the production of TMT bars is crucial for ensuring structural integrity in construction. Addressing common defects through careful monitoring, standardized processes, and advanced technology can significantly improve the quality of TMT bars. Continuous training and adherence to quality control measures will also play a pivotal role in minimizing these defects.
Explore the innovative world of trenchless pipe repair with our comprehensive guide, "The Benefits and Techniques of Trenchless Pipe Repair." This document delves into the modern methods of repairing underground pipes without the need for extensive excavation, highlighting the numerous advantages and the latest techniques used in the industry.
Learn about the cost savings, reduced environmental impact, and minimal disruption associated with trenchless technology. Discover detailed explanations of popular techniques such as pipe bursting, cured-in-place pipe (CIPP) lining, and directional drilling. Understand how these methods can be applied to various types of infrastructure, from residential plumbing to large-scale municipal systems.
Ideal for homeowners, contractors, engineers, and anyone interested in modern plumbing solutions, this guide provides valuable insights into why trenchless pipe repair is becoming the preferred choice for pipe rehabilitation. Stay informed about the latest advancements and best practices in the field.
2. ISSN: 2088-8694
IJPEDS Vol. 6, No. 2, June 2015 : 253 – 259
254
through diode Dp, which is connecting the input ac source to the output ground. During the negative half-line
cycle, the second part of circuit, L2- Q2- C2- L3- Do, is active through diode Dn, which is connecting the
input ac source to the output ground. Generally it is sufficient to analyze the circuit only during the positive
half of the input voltage. Apart from that, the operation of the proposed rectifiers will be briefly described by
assuming that the three inductors are operating in DCM. Because of this several advantages can be gained.
These advantages include the following: there is approximate near-unity power factor, the power switches are
turned on at zero current, and the output diode Do is turned off at zero current. Thus, the losses due to the
turn-on switching and the reverse recovery of the output diode are considerably reduced. Due to filter circuit
across the output DC is ripple free. Coupled inductors are also used to reduce the ripple content in the circuit.
Similarly the Efficiency of the proposed converter can be improved.
Figure 1. Proposed SEPIC Converter
2.2. Efficiency Improvement
The efficiency of the proposed converter can be improved by i). The voltage drop of a MOSFET is
ignored, ii). The power dissipation of the reduced components is theoretically calculated. This is done with
the assum ption that the forward voltage drops of all diodes are 0.5 V.
1
2 (1)
∆ / (2)
In this case when the proposed gate signals are applied to the converter, one diode of a rectifier,
including the intrinsic body diode, is omitted in a switching period. So, the efficiency improvement of the
proposed converter is obtained.
2.3. Frequency Response Analysis
The power stage specifications of the bridgeless SEPIC PFC converter are designed with following
power stage parameters like Input voltage, Output voltage, Output power, Switching frequency, Power
Factor. According to the design specification parameters, the state vectors for both switching intervals (in the
equation 3 & 4) and a quasi-state assumption, following the numerical expression of the control-to-inductor
current transfer function is obtained assuming an input voltage.
1
0 0 0 0
0 0 0 0
0
1
1
0 0
0 0 0 1/ 0
(3)
3. IJPEDS ISSN: 2088-8694
Closed Loop Analysis of Bridgeless SEPIC Converter for Drive Application (M. Gopinath)
255
B1
0
0
(4)
3 2 3.96
4 3 2 1 3.49
(5)
1 / 1 1 (6)
Figure 2 shows the frequency response of the derived control-to-inductor model. As there are 2
resonance locations, and one among them has very high Q-factor. In addition, from the state-matrix and the
transfer function with the characterized parameters, the locations of resonance points are determined as
shown in equation-6. Those locations are related to the main passive components and the duty cycle that
presents the relation between the input voltage and the output voltage.
Figure 2. Frequency response of input voltage
3. SIMULATION ANALYSIS
The performance of the proposed modeled is evaluated Using Matlab-Simulink environment, and it
is extended to drive applications. The simulation of bridgeless SEPIC converter is shown in Figure 3, which
gives a low conduction loss and switching loss during switch turn on and turn off condition. Figure 4 shows
the input voltage and current waveform. This circuit also used to improve power factor during conversion of
ac-dc. Here three identical inductors are used to reduce the ripple current. The output voltage measures 59
volts and current measures 1.4 amps from the Figure 5
4. ISSN: 2088-8694
IJPEDS Vol. 6, No. 2, June 2015 : 253 – 259
256
Figure 3. Simulation of Proposed Circuit
Figure 4. Measured Input Voltage and Current Figure 5. O/P Voltage= 59 v, Current=1.4 A
Figure 6 depicts the closed loop simulation circuit using PI controller, where input side voltage
disturbances are created at a specified time. During open loop system output voltage of open loop with
disturbance remains constant till the time of disturbance given by PI controller.
Figure 6. Closed loop Analysis of Proposed Converter
5. IJPEDS ISSN: 2088-8694
Closed Loop Analysis of Bridgeless SEPIC Converter for Drive Application (M. Gopinath)
257
The input voltage disturbance is done using PI controller and it gets reflected in the output side, leading to
reduction in the output voltage. During this time the closed loop PI circuit with PWM controller helps in
reducing the overshoot caused due to open loop.
The output voltage is continuously compared with a reference voltage using a differential amplifier.
The differential signal is amplified and fed to comparator. The comparator output is fed to one of the
MOSFET switches. Another triangular wave is phase shifted by 180º is compared with the same differential
amplifier output and the output of the second comparator is fed to the other MOSFET. Thus changes in the
output voltage are reflected in the differential amplifier output and in turn in the comparator output. Figure 7
gives the output DC voltage of the closed loop circuit. Figure 8 shows the step change in the torque at 1 sec
and from Figure 9, the speed attains its steady state instantly after the step change in the load torque.
From Figure 10, the THD mains current of the proposed PFC SEPIC converter fed DC drive is
observed under 5%, which is the requirement of power quality.
Figure 7. DC Output Voltage Figure 8. Change in load torque at time t= 1 sec
Figure 9. Speed response of close loop system Figure 10. THD Value of Proposed Converter
6. ISSN: 2088-8694
IJPEDS Vol. 6, No. 2, June 2015 : 253 – 259
258
4. EXPERIMENTAL ANALYSIS OF SEPIC CONVERTER
Figure 11 shows the hardware board with top side for main switches and bottom side for controller.
The output voltage is regulated and the input current tracks the input voltage. Under full-load condition, the
power factor and the harmonic distortion result can be analyzed from Figure 12. Harmonic components are
shown in Table 1. The major objective of the analysis is to compensate the power stage with proper damping
and to ensure the stable operation of converter. Bridgeless SEPIC PFC topologies can further improve the
conversion efficiency. To maintain same efficiency, the improved circuits could operate with higher
switching frequency.
Figure 11. Hardware of Proposed Converter Figure 12. Input AC and output DC signals of
proposed converter
Table 1. Harmonic components
Fundamental 3 5 7 9
1.448A 0.067A 0.097A 0.044A 0.009A
5. CONCLUSION
In order to improve the efficiency, bridgeless SEPIC converter has been proposed. Performance of the proposed
SEPIC PFC rectifier is carried out using Matlab Simulink software. The frequency response of the derived control-to-
inductor model is analyzed for the proposed converter. In our analysis Bridgeless SEPIC PFC rectifier suffers a step input
voltage change and thereby it attains the steady state. Besides in improving the circuit topology the performance can be
further reduce in rectifier size could be realized by integrating the three inductors. The simulation results are presented to
verify the controller design. The experiment results indicate that the harmonic contents are well below the limits. It is
verified that a well-designed damping circuit reduces the high risk of system instability. Simulation and hardware results
show high performance in terms of high power factor and efficiency.
REFERENCES
[1] Garcia, O., Cobos, J.A., Prieto R., Alou P., Uceda, J., “Single Phase Power Factor Correction : A Survey”, IEEE
Transactions on Power Electronics, vol. 18, no. 3, pp. 749-755, May 2003.
[2] Lazaro A., Barrado A., Sanz M., Salas V., Olias E., “New Power Factor Correction AC-DC Converter with
Reduced Storage Capacitor Voltage”, IEEE Transactions on Industrial Electronics, vol. 54, no. 1, pp.384-397, Feb.
2007.
[3] Liang T.J., Yang L.S., Chen J.F., “Analysis and design of a single-phase AC/DC step-down converter for universal
input voltage”, IET Electric Power Applications, vol. 1, no. 5, pp. 778-784, Sept. 2007.
[4] B. Su and Z. Lu, “An interleaved totem-pole boost bridgeless rectifier with reduced reverse-recovery problems for
power factor correction”, IEEE Trans. Power Electron., vol. 25, no. 6, pp. 1406-1415, Jun. 2010.
[5] H.Y. Tsai, T.H. Hsia, and D. Chen, “A family of zero-voltage-transition bridgeless power-factor-correction circuits
with a zero-current-switching auxiliary switch”, IEEE Trans. Ind. Electron., vol. 58, no. 5, pp. 1848-1855, May
2011.
[6] J.P.R. Balestero, F.L. Tofoli, R.C. Fernandes, G.V. Torrico-Bascope, and F.J.M. de Seixas, “Power factor
correction boost converter based on the three-state switching cell”, IEEE Trans. Ind. Electron., vol. 59, no. 3, pp.
1565-1577, Mar. 2012.
7. IJPEDS ISSN: 2088-8694
Closed Loop Analysis of Bridgeless SEPIC Converter for Drive Application (M. Gopinath)
259
[7] L. Huber, Y. Jang, “Performance of evaluation for bridgeless PFC buck rectifier”, IEEE Trans. Power Electron.,
vol. 23, no. 3, pp. 1381, May 2008.
[8] W. Wei, L. Hongpeng, J. Ahigong, and X. Ianguo, “A novel bridgeless buck-boost PFC converter”, in Proc. IEEE
Power Electron. Spec. Conf., 2008, pp. 1304-1308.
[9] W. Wei, L. Hongpeng, J. Shigong, and X. Dianguo, “A novel bridgeless buck-boost PFC converter”, in Proc. IEEE
Power Electron. Spec. Conf., 2008, pp. 1304-130.
[10] E.H. Ismail, “Bridgeless SEPIC rectifier with unity power factor and reduced conduction loss
[11] D.S.L. Simonetti, J. Sebastian, and J. Uceda, “The discontinuous conduction mode Sepic and Cuk power factor
preregulators: Analysis and design”, IEEE Trans. Ind. Electron., vol. 44, no. 5, pp. 630-637, Oct. 1997.
[12] D.M. Mitchell, “AC-DC Converter having an improved power factor”, U.S. Patent 4,412,277, Oct. 25, 1983.
[13] Younghoon Cho, “A Low Cost Single-Switch Bridgeless Boost PFC Converter”, in International Journal of Power
Electronics and Drive System. Vol. 4, No. 2, June 2014.
[14] Laxmi Devi Sahu, Satya Prakash Dubey, “ANN based Hybrid Active Power Filter for Harmonics Elimination with
Distorted Mains”, in International Journal of Power Electronics and Drive System, Vol. 2, No. 3, September 2012,
pp. 241~248.
BIBLIOGRAPHIES OF AUTHORS
GOPINATH MANI has obtained his B.E degree from Bharathiar University, Coimbatore in the
year 2002. He obtained his M-Tech degree from Vellore Institute of Technology; Vellore in the
year 2004. He obtained is Doctorate from Bharath University, Chennai. He is working as a
Professor/EEE, at Dr.N.G.P Institute of Technology, Coimbatore, India. His Area of interest is
Power Electronics. He is professional member of IEEE, ISTE, IETE, IAENG, and IACSIT. He
has received best performer award in the year 2010.
G. GOPU has obtained his B.E degree from Annamalai University, Chidambaram in the year
1996. He obtained his Master degree in Biomedical Signal Processing and Instrumentation in the
year 2002 from SASTRA University, Thanjavur and completed his Ph.D in Biomedical
Engineering at P.S.G College of Technology, Coimbatore under Anna University, Chennai. At
present he is working as a Professor and Head/Biomedical, at Sri Ramakrishna Engg College,
Coimbatore, India. His Area of interest is Medical Instrumentation, Power Electronics. He is
professional member of IEEE, ISTE, BMESI