In India most of the peoples are using two wheelers .In the recent days it has been found that many people are met with accidents due to several factors such as over speed, not wearing helmet, by not removing side stand, etc.,.. Accidents may happen due to the following reasons viz. 1) During after Consumption of Alcohol 2) overtaking of vehicles 3) Careless driving in speed breakers. This project will be helpful in reducing the possibility of accidents and also for antitheft system. Our Proposed system will overcome the above mentioned drawbacks. In this system, RF Sensor, REED Sensor, Ultrasonic Senor, Gas Sensors are used.

1. S.AGARAMUDHALVAN
MECHANICALENGINEERING

2. S.AGARAMUDALVAN, II ND YEAR, MECHANICAL ENGINEER.
I am pursuing II nd year mechanical Engineering in C.K COLLEGE OF ENGINEERING & TECHNOLOGY AT CUDDALORE.
I designed an intelligent two wheeled motor vehicle to save the human life.
Causes of accidents:
1. Careless driving. 2. Driving without helmet.3. Drunken drive. 4. Driving fast without knowing speed brakers.5. Driving
off the side stand and 6. Overtake.
Due to this the accidents are more and more life-threatening. I am using new a technology in two wheeled motor vehicle to prevent
such accidents.
CAN DRINK THE LIQUOR AND RUN THE INTELLIGENT TWO WHEELED MOTOR VEHICLE?
If you drink the liquor and sit in the vehicle, the vehicle will not start because i have a gas sensor. This gas sensor sense the smell of the alcohol
from the body and stop the ignition system it does not let the vehicle run.
CAN DRIVE THE INTELLIGENT TWO WHEELED MOTOR VEHICLE WITHOUT TAKING SIDE STAND ? For this case i have a
read sensor. It stop the ignition system it does not let the vehicle run.
CAN DRIVE THE INTELLIGENT TWO WHEELED MOTOR VEHICLE WITHOUT HELMET ? The vehicle cannot be run without
helmet. I have used a RF sensor frequency 420.
Can Overtake? We have RF sensor frequency 840 control the speed of vehicle when driving/overtake or high speed.
CAN DRIVE FASTER IN SPEED BREAKERS ? We have ultrasonic sensor it reduce the speed when speed breakers ahead. I have also
using smart card to start the vehicle to keep away from theft.
REPORT FOR SMART BIKE

3. In India most of the peoples are using two wheelers .In the recent days it
has been found that many people are met with accidents due to several
factors such as over speed, not wearing helmet, by not removing side
stand, etc.,.. Accidents may happen due to the following reasons viz. 1)
During after Consumption of Alcohol 2) overtaking of vehicles 3)
Careless driving in speed breakers. This project will be helpful in reducing
the possibility of accidents and also for antitheft system. Our Proposed
system will overcome the above mentioned drawbacks. In this system, RF
Sensor, REED Sensor, Ultrasonic Senor, Gas Sensors are used.
ABSTRACT

4. PIC MOTHER BOARD
 Pic mother board is a one of the brain in our smart bike project.
 This board memory capacity is high.(14kb)
 This board is fixed in IC chip. IC chip means integrated chip
 Microcontroller has a CPU, in addition with a fixed amount of RAM, ROM and other peripherals all
embedded on a single chip.
 This chip fixed on 40 connectors.
 This chip programme on C added for more specification on electronic and based on controller parts of the
system.

5. RELAY BOARD
 A relay is an electrically operated switch.
 It is the one part of heart in our smart bike.
 It supplies the power in a circuit of mother pic board.
 It supplies a power is 5v operation.
 It individual supplies for all sensors.
 Many relays use an electromagnet to mechanically operate a switch, but
other operating principles are also used, such as solid-state relays.

6. Led display(light emitting device)
 If any instruction shown on LED display.
 It is 5v operation.

7. RF ID SENSOR
 RFID sensor means radio frequency identity .
 The RF sensor shown on id card , then only ignition will be start.
 The RF id card insert the chip of the transmitter.
 RF sensor fixed in the pic mother board in receiver .
 Then goes to next step of password setting process.
 The frequency range is 300 feet to accept the card.
 5v operation.

8. KEYPAD OPERATION
 First process is going on smart card, then second process,
 Keypad process to access the code then will be go to starting on ignition.
 Then will be show on LED display.

9. Reed sensor specification
 Reed sensor is otherwise know as magnetic sensor.
 There are two pieces of reed sensor attached in the side stand one is fixed in the
stand and another one is fixed near the stand.
 The two sensors are joined the circuit will be cutoff the pic board .
 When bike will be ride then put on the stand.
 Warning Shown on the LED display , then suddenly bike will be stop.
 There is no need frequency.

10. RF SENSOR TRANSMITTER & RECEIVER
 RF signals travel in the transmitter and receiver.
 It operates at a specific frequency of 433MHz.
 5V operation.
 RF SENSOR one is placed in a helmet in a transmitter.
And one is fixed in board on receiver.
 And another process used in speed breaker mood fixed in speed breaker on RF sensor .
 Transmitter fixed on road and receiver fixed on board.
 Then only automatically applied on braking system.

11. GAS SENSOR SPECIFICATION
 This type of gas sensor is MQ7.
 Its frequency range is 1-100mega
 5V operation.
 High sensitivity to alcohol , Methane, CO Smoke, and Propane ,etc.
 Analog output varies corresponding to the gas concentration level in the air.
 Digital output is high when gas concentration is high and low when gas concentration is low.
 LEDs for output and power.
 Output sensitivity adjustable.
 Weight approximate: 12g.

12. Ultrasonic sensor
 ultrasonic sensors are a type of acoustic sensor divided into three broad categories .
 transmitters, receivers and transceivers. Transmitters convert electrical signals into ultrasound, receivers
convert ultrasound into electrical signals, and transceivers can both transmit and receive ultrasound.
 5V operation.
 Its frequency range is 1-100mega.
 Ultrasonic sensor to detect the object distance Upto 1-10 meter .
 Then detect the object suddenly shown on LED display , then brake will be apply on 12v DC wiper motor.

13.  When the bike deduct the ultrasonic to message the
pic mother board to alert the automatic braking system in
the back wheel will be push on the auto brake .
Brake is used for 12v DC wiper motor.
BRAKING SYSTEM

14. S.NO DESCRIPTION AMOUNT
1 PIC Mother Board 15000
2 Ultrasonic Sensor 500
3 Reed Sensor 250
4 Alcohol Gas Sensor 250
5 Transmitter Sensor 250
6 DC Wiper Motor (12V) 2000
7 Other Connecting Wires 2000
Total Rs.20,000/-
COST ESTIMATION

15. FINALLY FIXED ON ALL
COMPONENTS IN SINGLE BOARD

16. THANTHI NEWSPAPER AWARD

17. This project published in daily Thanthi newspaper and Telecasted in Thanthi News
channel
This project won 1stthe prize in overall Cuddalore district in the competition
conducted on Road Safety Awareness by Tamilnadu Police.
This project also Telecasted in Vasanth TV news channel (Sigaram thodu).
This project had a participation in DR.Kalam Young achiever award Competition
(World Youth Federation).
This project won 1st prize at best engineering project award at Neyveli Lignite
Corporation.
ACHIEVEMENTS

18.  This project won 1st prize at yaswanthara engineering college at Nagpur.
This project won 1st prize at ANNAUNIVERSITY at panruti campus.
This project also applied for pattern system in Tamilnadu government sector.
This project won 1st prize at Manakular vinayagar institute of technology at
puducherry. (puducherry university).
This project won 1st prize at MRK College of engineering and technology.

19.  In these days, people are met with lot of accidents.
 Consequently, we as Engineers need to take some step against this and provide the
desired way out. For the safety of the human beings some methodology is adopted.
 The persistence of such a model is to progress a system to detect fatigue symptoms in
drivers and control the fatigue of the rider.
 Progressive technology offers some confidence to avoid these accidents up to some
extent. This project involves various sensors for controlling the accidents. This project is
useful for human beings. 1) Consumption of Alcohol while driving 2) overtaking of
vehicles 3) Careless driving in speed breakers 4) not removing side stand, This project
also helpful for anti theft system. It is a good source and helpful for safety of People.
CONCLUSION

20. FUTURE ENHANCEMENT
 To improve the rescue assistance in the accident spot, image processing can be used more
effectively in order to determine the environmental factor with the exact location using GPS.
 This provides the latitude and longitude information about vehicle location through GSM.
 Vibration sensors are also fixed to measure the damage of the vehicle.
 Based on the frequency values, the damage condition of the vehicle is measured.
 If a vehicle has met with an accident, vibration sensor gives signal to the system and image is sent
to the hospital server. Based on this ambulance will be sent to defined location.

21. HYBRID VEHICLES

22. Most importantly, we are taking a huge step
towards a better future by accelerating the
transition to sustainable transportation."