This document provides standards for hollow and solid lightweight concrete blocks used in construction. It specifies:
1) Two grades (A and B) for load-bearing blocks based on intended use and weather protection.
2) Nominal dimensions for blocks ranging from 100-600mm in length, 50-300mm in width, and 100-200mm in height.
3) Tolerances of +/-5mm for length and +/-3mm for height and width.
4) Requirements for block density, compressive strength, water absorption, and drying shrinkage that vary based on grade.
This document provides the specification for concrete masonry units including hollow and solid concrete blocks. It defines key terms, specifies dimensions and tolerances for blocks, and classifies blocks into different grades based on their density and compressive strength. The standard aims to promote the use of concrete masonry in construction by specifying requirements for different types of blocks to allow for load-bearing and non-load-bearing walls as well as other applications.
This document is the Indian Standard Specification for Concrete Masonry Units Part I: Hollow and Solid Concrete Blocks. It outlines specifications for the production of hollow and solid concrete blocks used in load-bearing and non-load-bearing walls. The standard specifies dimensions, tolerances, classifications based on density and compressive strength, and physical properties for the blocks. It provides requirements for hollow and solid concrete blocks to ensure quality, durability and structural integrity in masonry construction.
This document provides the code of practice for constructing hollow concrete block masonry walls in India. It outlines the materials used such as hollow concrete blocks, cement, lime, sand and water. It provides specifications for mortar mixes and concrete fills. It also covers design considerations such as the thickness of load-bearing versus non-load-bearing walls. The code is intended to guide builders on the proper construction techniques and details to ensure successful performance of hollow concrete block masonry.
This document provides the specifications for concrete porous pipes used for under drainage. It outlines the materials, shapes and dimensions, manufacturing requirements, and testing procedures for such pipes. Key points include:
- Cement must conform to Indian Standards IS 269 or IS 455, or high alumina cement if required. Aggregates must pass a 20mm sieve and be retained on a 4.75mm sieve.
- Pipes can have uniform diameters and thicknesses with butt ends, or rebated/ogee ends for joints. Dimensions and tolerances are provided in tables.
- Manufacturing must result in accurate dimensions. Non-porous inverts may be included.
- Tests include a load
The document describes Indian Standard code IS:2911 (Part I/Sec I) - 1979 which provides guidelines for the design and construction of driven cast in-situ concrete pile foundations. It covers necessary considerations for pile type, size, installation depth, load testing, and other factors based on site conditions and project requirements. Subsurface investigation data on soil properties, groundwater levels, and chemical testing is required to properly design and install pile foundations. The standard has been revised to incorporate recent developments and separate pile foundation types into distinct sections for ease of use.
This document provides information on Indian Standard IS:2911 regarding the design and construction of pile foundations. It outlines the necessary members of the committee working on revising the standard. The standard covers driven precast concrete piles, providing guidance on pile design, construction methods, site investigation needs, and other relevant details. It aims to incorporate recent developments in pile foundation engineering practices in India.
Enhancing Resistance Capacity of Soft Storey Building by Means of Shearwall I...IRJET Journal
This document presents a study on enhancing the seismic resistance of soft-storey buildings through the use of shear walls. A parametric study was conducted on buildings with different ground floor heights, soil types, and lateral load resisting systems (ordinary moment frames, frames with shear walls, frames with masonry infill modeled as equivalent struts). Static analysis found that shear walls and struts reduced lateral drift, and stiffer soils reduced base shear. Pushover analysis determined that steel shear walls performed best but were too costly, while composite walls provided an economical improvement in strength over concrete shear walls. The inclusion of masonry infill struts further improved strength by up to 12.7%. In conclusion, composite shear walls with
The document discusses steel formwork used for constructing concrete structures. Steel formwork consists of panels made from steel plates reinforced with steel angles. It has advantages over wooden formwork like strength, durability, and producing a smooth concrete surface. The time required to remove formwork depends on factors like cement type and weather conditions. Steel formwork requires maintenance like leveling plates but can be reused numerous times on projects.
This document provides the specification for concrete masonry units including hollow and solid concrete blocks. It defines key terms, specifies dimensions and tolerances for blocks, and classifies blocks into different grades based on their density and compressive strength. The standard aims to promote the use of concrete masonry in construction by specifying requirements for different types of blocks to allow for load-bearing and non-load-bearing walls as well as other applications.
This document is the Indian Standard Specification for Concrete Masonry Units Part I: Hollow and Solid Concrete Blocks. It outlines specifications for the production of hollow and solid concrete blocks used in load-bearing and non-load-bearing walls. The standard specifies dimensions, tolerances, classifications based on density and compressive strength, and physical properties for the blocks. It provides requirements for hollow and solid concrete blocks to ensure quality, durability and structural integrity in masonry construction.
This document provides the code of practice for constructing hollow concrete block masonry walls in India. It outlines the materials used such as hollow concrete blocks, cement, lime, sand and water. It provides specifications for mortar mixes and concrete fills. It also covers design considerations such as the thickness of load-bearing versus non-load-bearing walls. The code is intended to guide builders on the proper construction techniques and details to ensure successful performance of hollow concrete block masonry.
This document provides the specifications for concrete porous pipes used for under drainage. It outlines the materials, shapes and dimensions, manufacturing requirements, and testing procedures for such pipes. Key points include:
- Cement must conform to Indian Standards IS 269 or IS 455, or high alumina cement if required. Aggregates must pass a 20mm sieve and be retained on a 4.75mm sieve.
- Pipes can have uniform diameters and thicknesses with butt ends, or rebated/ogee ends for joints. Dimensions and tolerances are provided in tables.
- Manufacturing must result in accurate dimensions. Non-porous inverts may be included.
- Tests include a load
The document describes Indian Standard code IS:2911 (Part I/Sec I) - 1979 which provides guidelines for the design and construction of driven cast in-situ concrete pile foundations. It covers necessary considerations for pile type, size, installation depth, load testing, and other factors based on site conditions and project requirements. Subsurface investigation data on soil properties, groundwater levels, and chemical testing is required to properly design and install pile foundations. The standard has been revised to incorporate recent developments and separate pile foundation types into distinct sections for ease of use.
This document provides information on Indian Standard IS:2911 regarding the design and construction of pile foundations. It outlines the necessary members of the committee working on revising the standard. The standard covers driven precast concrete piles, providing guidance on pile design, construction methods, site investigation needs, and other relevant details. It aims to incorporate recent developments in pile foundation engineering practices in India.
Enhancing Resistance Capacity of Soft Storey Building by Means of Shearwall I...IRJET Journal
This document presents a study on enhancing the seismic resistance of soft-storey buildings through the use of shear walls. A parametric study was conducted on buildings with different ground floor heights, soil types, and lateral load resisting systems (ordinary moment frames, frames with shear walls, frames with masonry infill modeled as equivalent struts). Static analysis found that shear walls and struts reduced lateral drift, and stiffer soils reduced base shear. Pushover analysis determined that steel shear walls performed best but were too costly, while composite walls provided an economical improvement in strength over concrete shear walls. The inclusion of masonry infill struts further improved strength by up to 12.7%. In conclusion, composite shear walls with
The document discusses steel formwork used for constructing concrete structures. Steel formwork consists of panels made from steel plates reinforced with steel angles. It has advantages over wooden formwork like strength, durability, and producing a smooth concrete surface. The time required to remove formwork depends on factors like cement type and weather conditions. Steel formwork requires maintenance like leveling plates but can be reused numerous times on projects.
Design principles in prefabricated structures unit iii ce6016 pfsPrakash Kumar Sekar
CE6016 PREFABRICATED STRUCTURES - Design principles in prefabricated structures unit iii ce6016 pfs - Disuniting of structures- Design of cross section based on the efficiency of material used – Problems in design because of joint flexibility ---- Allowance for joint deformation
This document provides an analysis and design of the structural elements for a multi-storey residential building, including slabs, columns, shear walls, and foundations. It discusses the objectives, general approach, types of buildings and concrete mixtures used. The structural elements are then analyzed and designed according to the given specifications and loadings, with reinforcement details provided for slabs, columns, shear walls, and pile caps.
Building Construction 8. formworks and scaffoldingsHamdija Velagic
This document provides information about formwork, scaffolding, shoring, and underpinning. It defines each construction technique and describes the typical components and uses. Formwork supports wet concrete until it cures and is used for foundations, walls, columns, slabs, beams, and stairs. Scaffolding provides temporary work platforms at different heights using standards, ledgers, and boards. Shoring supports unsafe structures using horizontal, vertical, or inclined bracing. Underpinning strengthens foundations by installing supports beneath them.
It is the presentation based on precast concrete construction which includes each and every point and scope which may be useful to civil engineering students
This document discusses various civil engineering applications of composite materials. It provides examples of composite materials being used for new bridge structures, enclosures, bonding steel plates, bonding carbon laminates and fiber fabrics, cables, ropes, tendons, rods, and anchors. It also discusses research and manufacturing related to composites. Specific projects where composites were used are described, such as footbridges in the UK, a bascule bridge, bridge soffit enclosures, and bridges where steel plates or carbon laminates were bonded for strengthening. Advantages of composites include high strength, low weight, versatility in design, durability, and reduced need for maintenance compared to steel.
This document provides guidelines for laying and finishing cement concrete flooring tiles. It discusses materials used, design considerations, necessary preparatory work, bedding, and grinding and polishing of tiles. The document specifies requirements for sand, cement, lime, tiles, pigments and water to be used. It also outlines information needed for planning tile work, time scheduling, and facilities required, such as completion of preceding work and protection against dampness.
IRJET- Comparative Study on the Seismic Behaviour of RCC and Steel-Concrete C...IRJET Journal
This document presents a comparative study on the seismic behavior of reinforced concrete concrete (RCC) frame structures and steel-concrete composite frame structures. Five 20-story building models are analyzed: one RCC structure and four composite structures with different column and beam configurations. Parameters like time period, story displacement, drift ratio, base shear, etc. are extracted and compared for the structures under equivalent static and response spectrum analysis for seismic zones II and V. The results show that composite structures have higher time periods and displacements but lower drift ratios and base shears compared to the RCC structure. In particular, composite model 3 with rectangular concrete filled steel columns performed better with smaller displacements and drift ratios.
This document provides information on formwork used for constructing concrete structures. It discusses the different types of formwork including wooden, plywood, steel and combined forms. It also describes requirements for proper formwork like being waterproof and strong enough to support loads. Common formwork systems are described for columns, beams, slabs, stairs and walls. Standards for stripping formwork from concrete structures are also outlined according to the Indian Standard code.
this slide about new Technics design sefl compecting concrete. it dose not required for compaction. its best to apply where compaction is not possible or critical.
Fibre reinforced and ferrocement car park pavers by R Sri RavindrarajahSriravindrarajah Rasiah
Published at the Proceedings of the X International Symposium on Ferrocement and Thin Reinforced Cement Composites (FERRO 10),held in Havana, Cuba in Oct. 2012
This lecture discusses precast concrete construction. It differentiates between architectural and structural precast concrete. Total precast construction uses only precast concrete for all building elements, while mixed precast combines precast with other materials. Joints and connections between precast elements are crucial and include slab to slab, slab to beam, and column to column connections. The construction process for precast buildings is similar to steel construction, with elements connected by welding or bolting after being lifted into place by crane.
Long-life concrete pavements in several countries were studied to identify techniques for achieving longer-lasting concrete pavements in the US. Key findings included the use of standard catalog designs optimized for 30+ year service lives, higher strength concrete mixtures with up to 4 aggregate size bins, and exposed aggregate surfaces for lower noise. Construction practices like two-lift paving allowed for recycling and provided durable surfaces, while maintenance was minimal due to the long design lives before rehabilitation. The scan identified opportunities to adapt proven international techniques to improve pavement performance and extend the life of US infrastructure.
Self-compacting concrete (SCC) was developed in Japan in the 1980s to solve issues with inadequate concrete compaction. SCC is highly flowable under its own weight and fills formwork without vibration. It was pioneered by Professor Hajime Okamura and has seen increasing use globally since 2000. The document discusses the constituents, properties, testing, and advantages of SCC compared to traditional vibrated concrete.
Concrete is a widely used construction material consisting of cement, water, and aggregates. The strength of concrete is specified using its 28-day cube strength in N/sq.mm. Formwork is used to mold wet concrete into desired shapes and allow it to cure. Formwork design involves choosing traditional or systematic approaches using wood or steel components like props, beams, sheathing to form columns, walls, and beams until the concrete gains sufficient strength. Proper formwork is important for quality concrete finish and structural integrity.
This document summarizes the design of untopped precast concrete diaphragms for two 5-story masonry buildings located in Birmingham, Alabama and New York City. It describes using 8-inch hollow core precast concrete planks for the floor and roof diaphragms. Design parameters are provided from another example. Forces are calculated based on standard equations, with the maximum force used for design. Connection details are from references, using shear friction with a coefficient of 1.0 due to intentionally roughened surfaces.
Reinforced concrete uses steel reinforcement bars embedded in concrete to resist tensile stresses that concrete cannot withstand on its own. The document discusses the composition, properties, and uses of plain cement concrete (PCC) and reinforced cement concrete (RCC). It explains that PCC is a mixture of cement, sand, aggregate and water, while RCC includes steel reinforcement to improve the concrete's tensile strength. The document also covers reinforcement techniques, types of reinforcing steel, mix proportions, characteristics of concrete structures, and ready-mix concrete.
Composite construction by Er. SURESH RAOAjit Sabnis
Presentation is a part of Structural Engg. series by ACCE(I) Institutes. Deals with details of Composite Structures-Design and Construction with case studies
Proposal defence slide on Analysis & Design of Multistoreylochan Shrestha
The document presents a structural analysis and comparison of design codes for a proposed 5.5 story reinforced concrete frame hospital building in Kathmandu, Nepal. It describes the building location, dimensions, structural system and objectives of analyzing the building using SAP2000 software and designing it according to Nepal's NBC and India's IS seismic codes. It also provides background on building analysis and design methods, factors of safety, load combinations specified in the two codes and their provisions for seismic analysis using the seismic coefficient and response spectrum methods.
This document provides information about different types of concrete materials used in construction. It discusses prestressed concrete, precast concrete, reinforced concrete, ready mix concrete, terrazzo concrete, and urbanite concrete. For each type, it provides definitions, general information, properties, applications, advantages and disadvantages. It includes images and illustrations to enhance understanding of the different concretes. The document is a research report on various building materials for a university assignment.
This document discusses composite construction and cambering of steel beams. It provides information on:
1) The composite construction process including use of composite metal decking, shear connectors, and concrete pouring to create a composite floor system that is stronger and stiffer than steel alone.
2) The advantages of composite construction such as reduced steel needs, lighter weight, and increased spans.
3) The cambering process of inducing a slight curvature in steel beams to compensate for deflection under loads in order to achieve a level floor slab.
4) When cambering is appropriate such as for filler beams, and when it is not such as for moment connected beams. Alternative methods to cambering like
This document describes test methods for determining the soundness of aggregates used in concrete. Specifically, it outlines procedures to test resistance to disintegration when aggregates are immersed in saturated solutions of sodium sulfate or magnesium sulfate. The test involves immersing aggregate samples in the solutions and observing for changes after a specified time period. This provides information about how aggregates may hold up against weathering effects from sulfate salts. The document specifies equipment, reagents, sample sizes and procedures needed to properly conduct the soundness test for both fine and coarse aggregates.
This document provides methods for determining the concentration of water soluble chlorides in concrete admixtures. It outlines three methods: volumetric, gravimetric, and turbidimetric. The volumetric and gravimetric methods are appropriate for higher chloride concentrations above 1% and 2.5% respectively. The turbidimetric method can detect lower concentrations down to 2 ppm. The document specifies reagents and procedures for each method.
Design principles in prefabricated structures unit iii ce6016 pfsPrakash Kumar Sekar
CE6016 PREFABRICATED STRUCTURES - Design principles in prefabricated structures unit iii ce6016 pfs - Disuniting of structures- Design of cross section based on the efficiency of material used – Problems in design because of joint flexibility ---- Allowance for joint deformation
This document provides an analysis and design of the structural elements for a multi-storey residential building, including slabs, columns, shear walls, and foundations. It discusses the objectives, general approach, types of buildings and concrete mixtures used. The structural elements are then analyzed and designed according to the given specifications and loadings, with reinforcement details provided for slabs, columns, shear walls, and pile caps.
Building Construction 8. formworks and scaffoldingsHamdija Velagic
This document provides information about formwork, scaffolding, shoring, and underpinning. It defines each construction technique and describes the typical components and uses. Formwork supports wet concrete until it cures and is used for foundations, walls, columns, slabs, beams, and stairs. Scaffolding provides temporary work platforms at different heights using standards, ledgers, and boards. Shoring supports unsafe structures using horizontal, vertical, or inclined bracing. Underpinning strengthens foundations by installing supports beneath them.
It is the presentation based on precast concrete construction which includes each and every point and scope which may be useful to civil engineering students
This document discusses various civil engineering applications of composite materials. It provides examples of composite materials being used for new bridge structures, enclosures, bonding steel plates, bonding carbon laminates and fiber fabrics, cables, ropes, tendons, rods, and anchors. It also discusses research and manufacturing related to composites. Specific projects where composites were used are described, such as footbridges in the UK, a bascule bridge, bridge soffit enclosures, and bridges where steel plates or carbon laminates were bonded for strengthening. Advantages of composites include high strength, low weight, versatility in design, durability, and reduced need for maintenance compared to steel.
This document provides guidelines for laying and finishing cement concrete flooring tiles. It discusses materials used, design considerations, necessary preparatory work, bedding, and grinding and polishing of tiles. The document specifies requirements for sand, cement, lime, tiles, pigments and water to be used. It also outlines information needed for planning tile work, time scheduling, and facilities required, such as completion of preceding work and protection against dampness.
IRJET- Comparative Study on the Seismic Behaviour of RCC and Steel-Concrete C...IRJET Journal
This document presents a comparative study on the seismic behavior of reinforced concrete concrete (RCC) frame structures and steel-concrete composite frame structures. Five 20-story building models are analyzed: one RCC structure and four composite structures with different column and beam configurations. Parameters like time period, story displacement, drift ratio, base shear, etc. are extracted and compared for the structures under equivalent static and response spectrum analysis for seismic zones II and V. The results show that composite structures have higher time periods and displacements but lower drift ratios and base shears compared to the RCC structure. In particular, composite model 3 with rectangular concrete filled steel columns performed better with smaller displacements and drift ratios.
This document provides information on formwork used for constructing concrete structures. It discusses the different types of formwork including wooden, plywood, steel and combined forms. It also describes requirements for proper formwork like being waterproof and strong enough to support loads. Common formwork systems are described for columns, beams, slabs, stairs and walls. Standards for stripping formwork from concrete structures are also outlined according to the Indian Standard code.
this slide about new Technics design sefl compecting concrete. it dose not required for compaction. its best to apply where compaction is not possible or critical.
Fibre reinforced and ferrocement car park pavers by R Sri RavindrarajahSriravindrarajah Rasiah
Published at the Proceedings of the X International Symposium on Ferrocement and Thin Reinforced Cement Composites (FERRO 10),held in Havana, Cuba in Oct. 2012
This lecture discusses precast concrete construction. It differentiates between architectural and structural precast concrete. Total precast construction uses only precast concrete for all building elements, while mixed precast combines precast with other materials. Joints and connections between precast elements are crucial and include slab to slab, slab to beam, and column to column connections. The construction process for precast buildings is similar to steel construction, with elements connected by welding or bolting after being lifted into place by crane.
Long-life concrete pavements in several countries were studied to identify techniques for achieving longer-lasting concrete pavements in the US. Key findings included the use of standard catalog designs optimized for 30+ year service lives, higher strength concrete mixtures with up to 4 aggregate size bins, and exposed aggregate surfaces for lower noise. Construction practices like two-lift paving allowed for recycling and provided durable surfaces, while maintenance was minimal due to the long design lives before rehabilitation. The scan identified opportunities to adapt proven international techniques to improve pavement performance and extend the life of US infrastructure.
Self-compacting concrete (SCC) was developed in Japan in the 1980s to solve issues with inadequate concrete compaction. SCC is highly flowable under its own weight and fills formwork without vibration. It was pioneered by Professor Hajime Okamura and has seen increasing use globally since 2000. The document discusses the constituents, properties, testing, and advantages of SCC compared to traditional vibrated concrete.
Concrete is a widely used construction material consisting of cement, water, and aggregates. The strength of concrete is specified using its 28-day cube strength in N/sq.mm. Formwork is used to mold wet concrete into desired shapes and allow it to cure. Formwork design involves choosing traditional or systematic approaches using wood or steel components like props, beams, sheathing to form columns, walls, and beams until the concrete gains sufficient strength. Proper formwork is important for quality concrete finish and structural integrity.
This document summarizes the design of untopped precast concrete diaphragms for two 5-story masonry buildings located in Birmingham, Alabama and New York City. It describes using 8-inch hollow core precast concrete planks for the floor and roof diaphragms. Design parameters are provided from another example. Forces are calculated based on standard equations, with the maximum force used for design. Connection details are from references, using shear friction with a coefficient of 1.0 due to intentionally roughened surfaces.
Reinforced concrete uses steel reinforcement bars embedded in concrete to resist tensile stresses that concrete cannot withstand on its own. The document discusses the composition, properties, and uses of plain cement concrete (PCC) and reinforced cement concrete (RCC). It explains that PCC is a mixture of cement, sand, aggregate and water, while RCC includes steel reinforcement to improve the concrete's tensile strength. The document also covers reinforcement techniques, types of reinforcing steel, mix proportions, characteristics of concrete structures, and ready-mix concrete.
Composite construction by Er. SURESH RAOAjit Sabnis
Presentation is a part of Structural Engg. series by ACCE(I) Institutes. Deals with details of Composite Structures-Design and Construction with case studies
Proposal defence slide on Analysis & Design of Multistoreylochan Shrestha
The document presents a structural analysis and comparison of design codes for a proposed 5.5 story reinforced concrete frame hospital building in Kathmandu, Nepal. It describes the building location, dimensions, structural system and objectives of analyzing the building using SAP2000 software and designing it according to Nepal's NBC and India's IS seismic codes. It also provides background on building analysis and design methods, factors of safety, load combinations specified in the two codes and their provisions for seismic analysis using the seismic coefficient and response spectrum methods.
This document provides information about different types of concrete materials used in construction. It discusses prestressed concrete, precast concrete, reinforced concrete, ready mix concrete, terrazzo concrete, and urbanite concrete. For each type, it provides definitions, general information, properties, applications, advantages and disadvantages. It includes images and illustrations to enhance understanding of the different concretes. The document is a research report on various building materials for a university assignment.
This document discusses composite construction and cambering of steel beams. It provides information on:
1) The composite construction process including use of composite metal decking, shear connectors, and concrete pouring to create a composite floor system that is stronger and stiffer than steel alone.
2) The advantages of composite construction such as reduced steel needs, lighter weight, and increased spans.
3) The cambering process of inducing a slight curvature in steel beams to compensate for deflection under loads in order to achieve a level floor slab.
4) When cambering is appropriate such as for filler beams, and when it is not such as for moment connected beams. Alternative methods to cambering like
This document describes test methods for determining the soundness of aggregates used in concrete. Specifically, it outlines procedures to test resistance to disintegration when aggregates are immersed in saturated solutions of sodium sulfate or magnesium sulfate. The test involves immersing aggregate samples in the solutions and observing for changes after a specified time period. This provides information about how aggregates may hold up against weathering effects from sulfate salts. The document specifies equipment, reagents, sample sizes and procedures needed to properly conduct the soundness test for both fine and coarse aggregates.
This document provides methods for determining the concentration of water soluble chlorides in concrete admixtures. It outlines three methods: volumetric, gravimetric, and turbidimetric. The volumetric and gravimetric methods are appropriate for higher chloride concentrations above 1% and 2.5% respectively. The turbidimetric method can detect lower concentrations down to 2 ppm. The document specifies reagents and procedures for each method.
This document provides specifications for concrete pavers. It outlines requirements for the materials, size, construction, capacity, and performance of concrete pavers. Some key points:
1) Concrete pavers are self-contained, self-propelled machines used to distribute concrete for road and runway construction.
2) Common paver sizes are 800 and 1000 liters, with non-tilting concrete mixers and booms that can place concrete from 0.65 to 3 meters above ground level.
3) Specifications include requirements for chassis, mixers, booms, buckets, operator stations, steering, power units, transmissions, controls, maintenance accessibility, interchangeability of parts, and finishing/painting
This document provides guidelines for the design and construction of bored precast concrete piles used for foundations. It outlines necessary site investigation information needed, equipment used, and design considerations. Bored precast piles involve boring holes and lowering precast concrete piles that are then grouted in place. Proper site data on soil conditions, groundwater levels, and structural loading is required. Equipment for boring, handling, and grouting the piles must be selected based on subsoil properties. Pile design should ensure loads are safely transmitted to the soil without failure or excessive settlement.
This document provides guidelines for welding mild steel plain and deformed bars used for reinforced concrete construction. It specifies various welding processes that can be used, including flash butt welding, manual metal-arc welding, oxy-acetylene welding, gas pressure welding, and thermit welding. It also provides requirements for welding equipment, electrodes, filler rods, welder qualifications, joint preparation, and inspection of welds. The guidelines are intended to help ensure welds meet minimum strength requirements for reinforced concrete applications.
This document outlines standards for the design and construction of machine foundations, specifically for impact type machines (hammers). It provides definitions for key terms related to hammer foundations, such as anvil, foundation block, impact force, and coefficient of restitution. It lists necessary data required for the design of hammer foundations, including hammer details, cushion pad details, soil data obtained through other Indian Standards, and information about the hammer location. The design criteria specify that hammer foundations must limit vibration transmission to adjacent foundations and withstand impact forces without damage.
This document outlines Indian Standard IS 1200 (Part 28) regarding the measurement of sound insulation work in building and civil engineering projects. It provides definitions and guidelines for measuring various types of sound insulation treatments. Measurements are to be taken in decimal units and recorded to two decimal places. Specific instructions are given for measuring insulation work on ceilings, floors, walls, curved surfaces, and at different heights. The standard aims to promote uniform and accurate measurement of sound insulation across different construction agencies and projects in India.
This document provides guidance on using epoxy injection to repair cracks in concrete structures. The method involves drilling holes along cracks, injecting epoxy under pressure, and allowing it to seep into the cracks. It can repair cracks as small as 0.002 inches. Epoxy injection requires skilled workers and specialized equipment. While it can effectively repair cracks temporarily, the underlying issues causing the cracks may remain if not addressed.
This document provides guidelines for the design and construction of raft foundations. It discusses different types of raft foundations and factors to consider in the design such as allowable bearing pressure, depth of foundation, subsoil water pressure, properties of the supporting soil, rigidity of the foundation and superstructure, and methods of analysis. The main methods of analysis described are the conventional or rigid foundation method based on linear distribution of contact pressure, and simplified flexible foundation methods. Design parameters like modulus of elasticity and subgrade reaction are also addressed.
This document provides specifications for autoclaved cellular (aerated) concrete blocks as part 3 of the Indian Standard for concrete masonry units. It outlines the classification of blocks into two grades based on compressive strength and corresponding density and thermal conductivity. Dimensional tolerances for the blocks are defined, with the maximum variation in length being 5mm and 3mm for height and width. The document also lists acceptable cement standards and provides context for the use of autoclaved cellular concrete blocks in construction.
This document provides a code of practice for the construction of autoclaved cellular concrete block masonry. It outlines materials and design considerations for constructing load-bearing and non-load bearing walls using these blocks. The document discusses block requirements, mortar mixes, wall thickness, bracing, and modular coordination. It aims to help builders properly use this type of masonry and ensure structural safety and avoidance of cracks.
This document provides the specification for precast reinforced concrete door and window frames. It outlines the requirements for the shape and dimensions of frames, acceptable materials, manufacturing process, and curing. Frames can be single-piece or assembled from separate vertical and horizontal members. Reinforcement is required and specifications are provided for concrete mix design, aggregates, and curing. Tolerances and options for decorative finishes are also included. The specification is intended to provide guidance for manufacturers and users of precast concrete door and window frames.
This document outlines specifications for precast concrete coping blocks. It specifies requirements for materials used in manufacturing coping blocks such as cement, aggregates, additives, and concrete strength. It also provides dimensions and tolerances for the cross-section and length of coping blocks. The specifications are intended to ensure coping blocks effectively prevent water penetration, direct water away from walls, resist displacement forces, allow for movement, and provide durability.
This document provides the specification for reinforced concrete fence posts according to Indian Standard IS:4996-1984. It outlines the materials, manufacturing process, shape and dimensions, and fixing of fencing wires for reinforced concrete fence posts. Some key points include:
- Cement, water, aggregates and reinforcement materials must meet standards specified.
- Posts are to be manufactured through mixing, placing and compacting concrete to be dense and free of voids.
- Reinforcement is to be properly positioned and anchored with minimum concrete cover requirements.
- Posts must cure for a minimum of 7 days and achieve a strength threshold before handling.
- Dimensions and tolerances are provided, with recommendations for line, strainer
This document is the Indian Standard (Part IX) from 1973 on the glossary of terms relating to cement concrete, focusing on structural aspects. It defines various structural terms used in cement and concrete technology to standardize terminology and avoid ambiguity. The definitions provided relate to elements like columns, beams, slabs, footings and their structural properties. The standard was developed with international coordination to harmonize with practices in other countries.
This document provides the summary of an Indian Standard code of practice for the design and construction of pile foundations. It specifically focuses on Section 2 which covers bored cast-in-situ concrete piles. Key points include:
1) It establishes terminology for bored cast-in-situ piles which are formed by excavating a hole in the ground and filling it with concrete, with or without a temporary casing.
2) It provides scope and covers the design and construction of bored concrete piles up to 2,500mm in diameter that transmit structural loads through end-bearing and/or shaft friction.
3) The standard references other related Indian Standards and international codes that were consulted in developing this practice.
The document is an Indian Standard code of practice for installing joints in concrete pavements. It provides definitions for different types of joints and pavements. It outlines design considerations for the layout and details of transverse and longitudinal joints. It specifies requirements for materials used in joints like joint filler, sealing compounds, and dowel bars. It describes the purpose and details of transverse expansion joints, contraction joints, and construction joints. The code aims to provide guidance on installing joints to control cracking and allow for movement in concrete pavements.
This document provides specifications for precast concrete kerbs, channels, edgings, quadrants, and gutter aprons. It outlines materials requirements including cement, aggregates, and concrete strength. It describes standard section dimensions and tolerances. Finish and color can be specified by the purchaser, with natural being default. The document aims to incorporate revisions from updated related standards to align with current Indian precast concrete industry practices.
This document provides the specifications for precast reinforced concrete street lighting poles. It outlines the materials, design considerations, testing requirements and more. Some key points:
- Poles must be a minimum of 5.2m in length, with mounting heights of at least 4m and planting depths of at least 1.2m.
- Concrete grade shall be at minimum M20. Reinforcement can be mild steel, medium tensile steel or deformed steel bars.
- Poles shall be designed to resist a maximum bending moment from loads like wind pressure and the weight of fixtures applied 600mm below the light source.
- Testing includes determining the ultimate transverse load at which the pole fails under a load
This document is the Indian Standard specification for coarse and fine aggregates from natural sources for use in concrete. It outlines various requirements for aggregates including limits on deleterious materials, aggregate crushing value, impact value, abrasion value, and soundness. It defines terms related to aggregates and specifies four grading zones for fine aggregates of different particle sizes. The standard is intended to ensure aggregates are suitable for producing durable concrete structures.
This document is the Indian Standard specification for coarse and fine aggregates from natural sources for use in concrete. It outlines the requirements and limits for quality parameters like deleterious materials, aggregate crushing value, impact value, abrasion value and soundness. It defines terms related to aggregates and specifies four grading zones for fine aggregates of progressively finer sizes. The standard is intended to cover aggregates commonly available in India for general structural and mass concrete construction.
This document provides guidelines for the structural design of concrete lining in rock tunnels. It discusses key considerations like studying the geology of the rock mass and characteristics, assessing rock loads on the lining and internal water pressure transmission. It recommends reinforcement be provided where needed to resist external loads from unstable ground or water pressures. Pressure tunnels should be reinforced if cover is less than internal pressure head. Reinforcement complicates construction so should be minimized where possible.
This document is Part IV of the Indian Standard Glossary of Terms Relating to Cement Concrete. It defines various types of concrete, including aerated concrete, autoclaved concrete, cast-in-place concrete, castable refractory, cellular concrete, and shotcrete/gunite. The definitions provided are intended to standardize terminology used in cement and concrete technology in India. The glossary was developed by the Cement and Concrete Sectional Committee of the Indian Standards Institution.
This document provides design tables for concrete structures used to store liquids. It includes tables for moment coefficients, shear coefficients, and other structural design values for rectangular and cylindrical concrete tanks. The tables are intended to aid engineers in quickly designing these types of structures. Rectangular tank tables cover individual wall panels and continuous walls, while cylindrical tank tables are also provided. Considerations for underground tanks subjected to earth pressures are discussed.
This document provides details on the design and construction of floors and roofs using precast reinforced or prestressed concrete ribbed or cored slab units. It specifies dimensions for the precast units, including widths up to 3000mm for ribbed units and 2100mm for cored units. It also provides requirements for material strengths, structural design considerations, and loads to be accounted for in design according to other relevant Indian Standards.
This document provides an overview of Indian Standard IS: 3370 (Part II) - 1965, which establishes guidelines for reinforced concrete structures used for liquid storage. It discusses the code's scope and general requirements. Key points include:
- The code provides uniform design and construction standards for liquid storage structures built with reinforced concrete.
- It addresses the assessment of loads, stresses, and statical equilibrium to ensure structural safety and prevent overturning.
- Design provisions are given for resistance to cracking and adequate strength based on permissible concrete and steel stresses.
- The code specifies stress limits for reinforced concrete elements in direct contact with stored liquids.
The document is the Indian Standard Specification for High Strength Deformed Steel Bars and Wires for Concrete Reinforcement. It outlines the requirements and testing procedures for steel reinforcement bars in three strength grades (Fe 415, Fe 500, Fe 550). Key points include:
- The standard covers manufacturing process, chemical composition limits, mechanical properties, and surface characteristics/deformations required for adequate bond with concrete.
- Steel bars must meet requirements for carbon, sulfur, phosphorus and mechanical properties depending on the specified strength grade.
- Deformations on the bar surface are specified as a minimum projected rib area to ensure adequate bond capacity.
- Bars can be manufactured by hot rolling followed by optional cooling/cold working
This document provides specifications for precast concrete cable covers. It classifies cable covers based on whether they are reinforced or unreinforced, and whether they have a peaked or flat design. Reinforced concrete covers with a peaked design are recommended for high voltage cables of 22kV and above. Unreinforced peaked covers are for voltages above 1kV but below 22kV. Unreinforced flat covers are used for cables up to and including 1kV. The document specifies requirements for materials, dimensions, reinforcement, and markings for the different types and classes of precast concrete cable covers.
This document provides the code of practice for the design and construction of conical and hyperbolic paraboloidal shell foundations. It discusses the preliminary design considerations for shell foundations, including determining the soil design to proportion the foundation dimensions based on allowable bearing pressure and net loading intensity, as well as the structural design of the shell. It also provides figures illustrating reinforcement details for conical and hyperbolic paraboloidal shell foundations. The code covers the relevant terminology and information needed for design, and notes the membrane analysis approach is commonly used for structural design of shell foundations.
28-5.21 Company Profile of Pyrmaid structural consultant.pptxBoopathi Yoganathan
Pyramid Structural Consultant provides structural design, building approval, and construction services. They have a team of experienced engineers and workers who use software like AutoCAD and STAAD to complete structural designs for RCC and steel buildings. Notable projects include the design of a G+1 residential building in Namakkal. They are located in Puduchatram, Namakkal and can be found on LinkedIn and Facebook.
This document provides a bonafide certificate for a project report on the study of mechanical properties of eco-friendly economic concrete. It certifies that the project was conducted by three students, M.Vineeth, Y.Boopathi, and P.Murali, in partial fulfillment of their Bachelor of Engineering degree from Kongu Engineering College. The project investigated replacing natural aggregates with steel slag aggregates and M-sand to produce more sustainable concrete. Tests were conducted to determine the compressive strength, split tensile strength, modulus of rupture, and modulus of elasticity of concrete mixes with varying replacement levels.
The document describes an experimental investigation into the properties of concrete with different replacement percentages of natural aggregates with manufactured sand and steel slag. The methodology involves collecting cement, fine aggregates (natural sand and m-sand), coarse aggregates, and steel slag. The mix design for M20 grade concrete is calculated and concrete specimens are cast. The specimens are cured and then tested to determine their mechanical properties. The results are compared to those of conventional concrete to evaluate the suitability of manufactured sand and steel slag as partial replacements for natural aggregates in concrete.
The document discusses two methods for mesh refinement - the p-method and h-method. The p-method increases the order of the polynomial used in the finite element model, allowing for more accurate results without changing the mesh. The h-method reduces the size of elements to create a finer mesh, better approximating the real solution in areas of high stress gradients. Both methods aim to improve the accuracy of finite element analysis results, with the p-method doing so without requiring changes to the mesh.
An embedded system is a dedicated computer system that performs specific tasks. An important application of embedded systems is anti-lock braking systems (ABS) in automobiles. ABS uses sensors and electronic control modules to monitor wheel speed and automatically modulate brake pressure to prevent wheel lockup and maintain steering control during emergency braking. By preventing skidding, ABS can help drivers stop more safely and shorten stopping distances on wet or slippery surfaces compared to standard brakes. ABS works by pulsing the brakes rapidly when it detects a wheel is about to lock up, which allows the wheel to continue turning and maintaining traction with the road.
This document discusses past earthquakes in India and retrofitting techniques for masonry structures. It summarizes the 2004 Indian Ocean earthquake and tsunami, which had a magnitude of 9.1-9.3 making it one of the largest ever recorded. Over 230,000 people were killed across 14 countries by the resulting tsunamis. The document then discusses failure modes of confined masonry walls and retrofitting techniques to improve seismic resistance, including adding horizontal reinforcement, improving wall density and tie columns. Key factors for seismic resistance of confined masonry structures are also summarized.
The document provides guidelines for selecting, splicing, installing, and protecting open cable ends for resistance-type measuring devices in concrete and masonry dams. It discusses cable specifications, approved splicing methods including vulcanized rubber splices, rubber sleeve covering, and self-bonding tape. It also covers cable and conduit selection, including choosing the proper conduit size based on the number and size of cables to be run. Proper installation techniques are outlined to protect cable runs within concrete structures.
This document provides information on an Indian Standard (IS) for a unified nomenclature of workmen for civil engineering. It was adopted in 1982 by the Indian Standards Institution Construction Management Sectional Committee. The standard aims to unify the different names used for workmen engaged in civil engineering works across India. It then lists the unified nomenclature for various types of workmen and for carts/animals commonly used in civil engineering works.
This document provides definitions for key terms related to concrete monolith structures used in port and harbour construction. It defines elements like the bottom plug, cutting edge, deck slab, dewatering, fascia wall, filling, kentledge, kerb, and monolith. A monolith is a large hollow rectangular or circular foundation sunk as an open caisson through various soil strata until reaching the desired founding level, at which point the bottom is plugged with concrete.
The document provides specifications for an apparatus used to measure the length change of hardened cement paste, mortar, and concrete. It describes the construction, dimensions, materials, and markings required for a length comparator, which uses a micrometer to measure the change in length of specimens against a reference bar. The length comparator consists of an adjustable frame that holds either a screw or dial micrometer and allows measurement of specimens of different lengths.
This document provides guidelines for designing drainage systems for earth and rockfill dams. It discusses key considerations like controlling pore pressures, internal erosion, and piping. The guidelines cover selecting appropriate drainage features based on the dam type and materials. Features discussed include inclined/vertical filters, horizontal filters, longitudinal and cross drains, transition zones, rock toes, and toe drains. Filter material criteria and design procedures are also outlined.
This document provides recommendations for welding cold-worked steel bars used for reinforced concrete construction according to Indian Standard IS 9417. It summarizes the key welding processes that can be used including flash butt welding, shielded metal arc welding, and gas pressure welding. For each process, it outlines preparation of the bars, selection of electrodes, welding procedures, and safety requirements. Diagrams are provided to illustrate edge preparation and sequences for multi-run butt welding and lap welding joints.
This document provides guidelines for lime concrete lining of canals. It discusses materials used for lime concrete lining such as lime, sand, coarse aggregate and water. It also discusses preparation of subgrade for different soil types including expansive soils, rock and earth. Compaction methods are provided for different soil types. The document also discusses laying of concrete lining and provides specifications for lime concrete mix such as minimum compressive and flexural strength.
This document provides guidelines for structural design of cut and cover concrete conduits meant for transporting water. It outlines various installation conditions for underground conduits and describes how to calculate design loads from backfill pressure, internal/external water pressure, and concentrated surface loads. Design loads include vertical and lateral pressure from backfill based on fill material properties, hydrostatic pressure from water surcharge, and dispersed point loads accounting for fill height and conduit geometry. The conduit is to be designed for the most unfavorable combination of these loads. Recommended fill material properties and methods for load and stress analysis are also provided.
This document provides guidelines for installing and observing cross arms to measure internal vertical movement in earth dams. It describes the components of the mechanical cross arm installation including the base extension, cross arm units, spacer sections, and top section. It provides details on installing each component as the dam is constructed in rock-free or rocky soils. Observation involves using a measuring torpedo attached to a steel tape or cable to take settlement readings from the installed cross arm system.
This document provides guidelines for instrumentation of concrete and masonry dams. It outlines obligatory and optional measurements for dams, including uplift pressure, seepage, temperature, and displacement. Obligatory measurements include uplift pressure, seepage, temperature inside the dam, and displacement measurements using plumb lines or other methods. Optional measurements that may provide additional insights include stress, strain, pore pressure, and seismicity measurements. The document describes different types of measurements in detail and how they can be used to monitor dam performance and safety over time.
This document provides guidelines for selecting measurement instruments and their locations for monitoring earth and rockfill dams. It describes various types of measurements needed, including pore pressure, movements, seepage, strains/stresses, and dynamic loads from earthquakes. Planning the instrumentation system is important to ensure required data is obtained during construction and the dam's lifetime. The document discusses different instruments for measuring vertical and horizontal movements, such as surface markers, cross-arm installations, hydraulic devices, magnetic probes, and inclinometers.
This document outlines specifications for concrete finishers used in construction. It specifies requirements for materials, size, construction, capacity, and performance. Key aspects include:
- Concrete finishers are used after spreaders to finish concrete laid by pavers.
- Materials must meet relevant Indian standards. Common sizes are 3-4.5m and 6-7.5m widths.
- Construction includes a steel frame, traction wheels, steering, adjustable screeds, vibrator attachment, drives, controls, and a diesel or petrol power unit.
- Performance requirements ensure the finisher can operate under different conditions to finish concrete slabs within specifications.
This document provides recommendations for using table vibrators to consolidate concrete. It discusses general considerations like the suitability of table vibrators, power units, handling the vibrator, and performance and sizing of vibrators. It also covers concrete mix design, formwork design, and testing of vibrating tables according to relevant Indian Standards. The key points are that table vibrators are well-suited for precast concrete elements, proper power units and maintenance are important, and concrete mix workability and form rigidity affect vibration effectiveness.
This document provides specifications for concrete spreaders. It outlines various types of concrete spreaders, including reciprocating-blade, screw, and trough-hopper types. It specifies requirements for the size, construction, materials, and performance of concrete spreaders. The construction section describes requirements for the chassis, wheels, scrappers, and operator's station. Tolerances for adjustments to the operating width are also specified.
How to Build a Module in Odoo 17 Using the Scaffold MethodCeline George
Odoo provides an option for creating a module by using a single line command. By using this command the user can make a whole structure of a module. It is very easy for a beginner to make a module. There is no need to make each file manually. This slide will show how to create a module using the scaffold method.
How to Make a Field Mandatory in Odoo 17Celine George
In Odoo, making a field required can be done through both Python code and XML views. When you set the required attribute to True in Python code, it makes the field required across all views where it's used. Conversely, when you set the required attribute in XML views, it makes the field required only in the context of that particular view.
Exploiting Artificial Intelligence for Empowering Researchers and Faculty, In...Dr. Vinod Kumar Kanvaria
Exploiting Artificial Intelligence for Empowering Researchers and Faculty,
International FDP on Fundamentals of Research in Social Sciences
at Integral University, Lucknow, 06.06.2024
By Dr. Vinod Kumar Kanvaria
A workshop hosted by the South African Journal of Science aimed at postgraduate students and early career researchers with little or no experience in writing and publishing journal articles.
This presentation was provided by Steph Pollock of The American Psychological Association’s Journals Program, and Damita Snow, of The American Society of Civil Engineers (ASCE), for the initial session of NISO's 2024 Training Series "DEIA in the Scholarly Landscape." Session One: 'Setting Expectations: a DEIA Primer,' was held June 6, 2024.
How to Manage Your Lost Opportunities in Odoo 17 CRMCeline George
Odoo 17 CRM allows us to track why we lose sales opportunities with "Lost Reasons." This helps analyze our sales process and identify areas for improvement. Here's how to configure lost reasons in Odoo 17 CRM
How to Add Chatter in the odoo 17 ERP ModuleCeline George
In Odoo, the chatter is like a chat tool that helps you work together on records. You can leave notes and track things, making it easier to talk with your team and partners. Inside chatter, all communication history, activity, and changes will be displayed.
1. IS:2185(Partll)-1983
( Superseding IS : 3590 - 1996 )
( Reaffirmed 1989 )
SPECIFICATION FOR
CONCRETE MASONRY UNITS
PART II HOLLOW AND SOLID LIGHTWEIGHT
CONCRETE BLOCKS
Third Reprint DECEMBER 1996
UDC 691.327-43V-478 : 666.973.6
Q Copyight 1983
BUREAU OF INDIAN STANDARDS
MANAK BHAVAN, 9 BAIiAbUR SHAH ZAPAR MARG
NEW DELHI 110002
Gr6 September 1983
2. IS : 2185( Part II ) - 1983
('SaperseedingIS:3590-1966)
Indian Standard
SPECIFICATION FOR
CONCRETE MASONRY UNITS
PART II HOLLOW AND SOLID LIGHTWEIGHT
CONCRETE BLOCKS
( First Revision )
Cement and Concrete Sectional Committee, BDC 2
Chairman
DR H. C. VISVESVARAYA
Members
Representing
Cement Research Institute of India, New Delhi
ADDITIONAL DIRECTOR, STAX- Research, Designs 8t Standards Organization
DARDS ( B 82 S )
DEPUTY DIRECTOR, STAN-
( Ministry of Railways )
DAKDS ( B & S ) ( Alternate )
SHRI K. P. BANERJEE Larsen & Toubro Ltd, Bombay
SHRI HARISH N. MALANI ( Alternate )
Smtr S. K. BANERJEE National Test House, Calcutta
SHRI R. N. BANSAL
DR N. S. BHAL
Beas Designs Organization, Nangal Township
Structural Engineering Research Centre ( CSIR I,
Roorkee
SHRI V. K. GHANEKAR (Alternate)
GRIEF EN~INEEXI( DESIGNS ) Central Public Works Department
EXECUTIVE EN~~NEEI~( DESI-
ON9 )-III ( Ahcrna;e )
CHIEF ENOINNER( PROJECTS) Irrigation Department, Government of Punjab,
DIRECTOR ( IPRI ) ( Alternate )
Chandigarh
DR S. K. CHOPRA Cement Research Institute of India, New Delhi
DR A. K. MULLICK (Alternate)
DIRECTOR Central Soil and Materials Research Station,
New Delhi
DEPUTY DIRGCTOR ( Alternate )
DIRECYOR ( C & MDD )-I Central Water Commission, New Delhi
DEPUTY DIRECTOR
( C & MDD-II ) ( Alternate )
SHRI T. A. E. D’Sa The Concrete Association of India, Eombay
SHEI R. N. GREEN ( Alternate )
( Continued on page 2 )
@ Copyright 1983
BUREAU OF INDIAN STANDARDS
This publication is protected under the Indian Copy@t Act ( XIV of 1937 ) and
reproduction in whole or in part by any means except with written permission of the
publisher shall be deemed to be an infringement of copyright under the said Act. I
3. IS : 2185( Part II ) - 1983
( Continued from page I )
Members Representing
SHRI V.K. GUPTA
SHRI S. N. PANDE ( Alternate )
Engineer-in-Chief ‘.s Branch, Army Headquarters
SHRI A. K. GUPTA Hyderabad Asbestos Cement Product Ltd,
DR IQBAL ALI
SHRI P. J. Jnous
SHRI N. G. JOSHI
SHRI S. R K~LKARNI
Sam S. K. LAHA
Hyderabad
Engineering Research Laboratories, Hvderabad
The Associated Cement Companies Ltd, Bombay
Indian Hume Pipe Company Ltd, Bombay
M. N. Dastur & Co Pvt Ltd, Calcutta
The Institution of Engineers ( India ), Calcutta
SHRI B. T. UNWALLA ( Alternate )
DR MOHAN RAI Central Building Research Institute . ( CSIR ),
Roorkee
DR S. S. RAH~I ( Alternaie )
SHRI K. K. NAMBIAR In personal capacity ( ‘Ramanalaya’, 11 First Crescent
Park Road, Gandhinagar, Adyar, Madras )
SERI H. S. PASRICHA Hindustan Prefab Ltd, New Delhi
SERI C. S. MISHRA ( Alternufe)
SHRI Y. R. PHULL Indian Roads Congress, New Delhi
SHRI Y. R. PHuLL Central Road Research Institute ( CSIR ),
New Delhi
SERI M.R. CHATTERJEE ( Alternate I )
SERI K. L. SETHI ( Alternate II )
DR M. RAMAIAH Struc$;;JasEngineering Researh Centre ( CSIR ),
DR A. G. MADRAVA RAO ( Alternate )
SHRI A. V. RAMANA Dalmia Cement ( Bharath ) Ltd, New Delhi
SARI G. RAMDAS Directorate General of Supplies and Disposals,
New Delhi
DR A. V. R. RAO National Buildings Organization, New Delhi
SHRI J. SEN GUPTA ( Alternate )
SH~I R. V. CHALAPATHI RAO Geological Survey of India, Calcutta
SERI S. ROY ( Alternate )
SERI T. N. S. RAO Gammon India Ltd, Bombay
SHRI S. A. REDDI ( Alternate )
SHIZIARSUN IZIJHSIN~HASI Cement Corporation of India, New Delhi
SHRI K. VITEAL RAO ( Alternate )
SHRI S. SEETHARAXAN Roads Wing ( Ministry of Shipping and Transport >
SERI N. SIVA~URU ( Alternate )
SECRETARY Central Board of Irrigation and Power, New Delhi
DEPUTY SECRETARY(I) ( Allernafe )
SERI K. A. SU~RAMANIAM The India Cements Ltd, Madras
SHRI P. S. RAMACHANDARAN ( Altnnufe )
SUPERINTENDING E~~C+INEERPublic Works Department, Government of
( DESIGNS) Tamil Nadu, Madras
EXECUTIVEENC+~EER( SM&R
DIVISION ) ( Alternate )
SHRI L. SWAROOP
SHRI G. RAMAN,
Director ( Civ Engg )
Orissa Cement Ltd, New Delhi
Director General, IS1 ( Ex-O&O Memh )
Secretary
SERI M. N. NEELAKANDEAX?
Assistant Director ( Civ Engg ), IS1 *
( Cotstint& ea paga 23 )
2
4. IS : 2185 ( Part II ) - 1983
Indian Standard
SPECIFICATION FOR
CONCRETE JMASONRY UNITS
PART II HOLLOW AND SOLID LIGHTWEIGHT
CONCRETE BLOCKS
( First Revision )
0. FOREWORD
0.1 This Indian Standard ( Part II ) ( First Revision ) was adopted by
the Indian Standards Institution on 28 February 1983, after the draft
finalized by the Cement and Concrete Sectional Committee had been
approved by the Civil Engineering Division Council.
0.2 This standard was first published in 1966 as ‘ IS : 35cO-1966
Specification for load bearing lightweight concrete blocks’. The first
revision is being issued under the modified title ‘ Specification for con-
crete masonry units: Part II Hollow and solid lightweight concrete blocks’
and supercedes IS : 3590-1966. Part I of this standard covers hollow
and solid concrete blocks of normal weight. This modification in title
is intended for facilitating the co-ordination of requirements of various
types of concrete masonry units, covered under various Indian Standards.
0.2.1 This standard incorporates significant modifications especially
with regard to the classification of the blocks and physical requirements
such as dimensions, compressive strength values, water absorption and
drying shrinkage. Also this revision covers hollow blocks of close-’
cavity type apart from hollow blocks of open cavity. The requiremen.;
of load bearing and non-load bearing blocks have been separately given
in this standard to the extent possible.
0.3 Concrete masonry, already extensively used in building construction
abroad, is likely to make very considerable headway in this country
because of the many advantages, such as durability, strength and struc-
tural stability, fire resistance, insulatton, and sound absorption it possesses.
Concrete masonry construction is also economical because of the follow-
ing aspects:
a) the units are relatively large and true in size and shape. This
insures rapid construction so that more wall is laid per man-hour
than in other types of wall construction;
3
5. IS : 21S5( Part II ) - 1983
b) fewer joints result in a considerable saving in mortar as compared
to hormal masonry construction; and
c) the true plane surface obtained does not require plaster. Even
when plaster is used for any reason, the quantity required for
satisfactory coverage is significantly small.
0.3.1 Concrete masonry has an attractive appearance and is readily
adaptable to any style of architecture. It lends itself to a wide
variety of surface finishes for both exterior and interior walls. It may
also be finished with cement plaster, gauged with lime or a plasticizer.
Concrete masonry units provide a strong mechanical key, uniting the
concrete masonry backing and the plaster finish in a strong permanent
bond.
0.4 Concrete masonry units are used for both load-bearing and non-load
bearing walls, for partitions and panel walls, as backing for other types
of facing material, for piers; pilasters and columns, for retaining walls,
garden walls, chimneys and fire places, as fillers in concrete joist floor
construction, and as shuttering for beams and lintels.
0.4.1 Concrete masonry units manufactured from lightweight aggre-
gate concrete are used for both load bearing and non-load bearing
internal wails, partition and panel walls, inner leaf of cavity walls or as
backing to brick masonry and for external load bearing walls as well as
panel walls in steel or reinforced concrete frame construction when
protected from weather hy rendering or by some other efficient treatment.
0.5 For the purpose of. deciding whether + particular requirement of
this standard is complied with, the final value, observed or calculated,
expressing the result of a test or analysis, shall be rounded off in accor-
dance with IS : 2-1960+. The number of significant places retained in
the rounded off value should be the same as that of the specified value
in this standard.
1. SCOPE
1.1 This standard ( Part II ) covers the following lightweight’ concrete
masonry building units which are used in the construction of load-bear-
ring and non-load bearing walls:
a) Hollow ( open and closed cavity ) load bearing concrete blocks,
b) Hollow ( open and closed cavity ) non-load bearing concrete
blocks,
*Rulesfor roundingoff numericalvalues( r&red) .
4
6. lSt21S5( Part u )--1983
c) Solid load-bearing concrete blocks, and
d) Solid non-load bearing concrete blocks.
NOTE- The requirements of cellular ( aerated ) concrete blocks are covered
in IS : 5482-1969*.
2. TERMINOLOGY
2.0 For the purpose
apply.
of this standard, the following definitions shall
2.1 Block - A concrete masonry unit, either hollow ( open or closed
cavity ), or solid or cellular ( other than units used for bonding, such as
a half block ), any one of the external dimensions of which is greater
than the corresponding dimension of a brick as specified in IS : 3952-1978t;
I and of such size and mass as to permit it to be handled by one man.
Furthermore, to avoid confusion with slabs and panels, the height of the
block shall not exceed either its length or six times its width.
2.2 Block Density - The density calculated by dividing the mass of a
block by the overall volume, including holes or cavities and end recesses.
2.3 Drying Shrinkage - The difference between the length of speci-
men which has been immersed in water and subsequently dried to
constant length, all under specified conditions; expressed as a percentage
of the dry length of the specimen.
2.4 Face Shells - The two outer plates of the hollow concrete block.
These are connected together by webs.
2.5 Gross Area - The total area occupied by a block on its bedding
face, including areas of cores and end recesses.
2.6 Height - The vertical dimension of the exposed face of a block,
excluding any tongue or other device designed to provide. mechanical
keying.
2.7 Hollow ( Open or Closed Cavity ) Concrete Block - A block
having one or more large holes or cavities which either pass through the
block ( open cavity ) or do not effectively pass through the block ( closed
cavity ) and having the solid material between 50 and 75 percent of the
total volume of the block calculated from the overall dimensions.
2.8 Length - The horizontal dimension of the exposed face of block,
excluding any tongue or other device designed to provide mechanical
keying.
*Specification for autoclaved cellular concrete blocks.
tSpecification for burnt clay hollow blocks for walls and partitions (jirstrsaision ).
5
7. IS L2185 ( Part II ) - 1983
2.9 Moisture Movement - The difference between the length of
the specimen when dried to constant length and when subsequently
immersed in water, all under specified conditions, expressed as a per-
centage of the dry length of the specimen.
2.10 Solid Block - A block which has solid material not less than
75 percent of the total volume of the block calculated from the overall
dimensions.
2.11 Webs - The solid sections of the hollow concrete blocks which
connect the face shells.
2.12 Width - The external dimension of a block at the bedding plane,
measured at right angles to the length and height of the block.
3. DIMENSIONS AND TOLERANCES
3.1 Concrete masonry building units shall be made in sixes and shapes
to fit different construction needs. They include stretcher, corner,
double corner or pier, jamb, header, bull nose, and partition block, and
concrete floor units.
3.2 Concrete Block -’ Concrete block, hollow ( open or closed cavity )
or solid shall be referred to by its nominal dimensions. The term
‘ nominal ‘, means that the dimension includes the thickness of the mortar
joint. Actual dimensions shall be 10 mm short of the nornina dimen-
sions ( or 6 mm short in special caies where finer jointing is specified ).
3.2.1 The nominal dimensions of concrete block shall be as follows:
Length 400,500 or 600 mm
Height 100 or 200 mm
Width 50,75, 100, 150,200,250 or 300 mm
In addition, block shall be manufactured in half lengths of 200, 250
or 300 mm to correspond to the full lengths.
The nominal dimensions of the units are so designed that taking
account of the thickness of mortar joints, they will produce wall lengths
and heights which will conform to the principles of modular co-ordma-
t ion.
3.2.2 Blocks of nominal dimensions other than those specified in 3.2.1
may also be used by mutal agreement between purchaser and supplier.
In the case of special concrete masonry units such as jallie or screen wall
block and ornamental block, the specified sizes shall not necessariIy apply.
3.2.3 The maximum variation in the length of units shall not be more
than + 5 mm and maximum variation in height and width of unit, n 01
more than f. 3 mm.
6
8. 4.1 Load bearing lightweight concrete masonry units hollow ( open and
closed cavity ) or solid shall conform to the following two grades:
4
b)
Grade A - These are used below and above ground level in damp-
proof course, in exterior walls that may or may not be treated
with a suitable weather-protective coating and for interior walls.
Grade B-These are used above ground level in damp-proof course,
in exterior walls that are treated with a suitable weather-protec-
tive coating and for internal walls.
IS : 2185 ( Part II ) - 1983
3.2.4 Hollow concrete blocks shall be made either with two cores or
three cores. Stretchers in the 200,250 and 300 mm widths shall generally
have concave ends, each end flange being grooved or plain. All 100 and
150 mm wide units shall generally be made with plain ends.
3.2.5 Face shells and webs shall increase in thickness from the bottom
to the top of the unit. Depending upon the core moulds used, the face
shells and webs shall be flared and tapered or straight tapered, the
former providing a wider surface for mortar. The minimum thickness
of the face shell and web shall be not less than 20 mm. However, for the
top face shell of the closed cavity units, the minimum thickness may be
less ,than 20 mm, but not less than 1.5 mm.
3.3 Subject to the tolerances specified in 3.2.3 and the provisions of 3.4
the faces of masonry units shall be flat and rectangular, opposite faces
shall be parallel, and all arises shall be square. The bedding surfaces
’ shall be at ri_ght angles to the fac.es of the blocks.
3.4 Blocks with Special Faces - Blocks with special faces shall be
manufactured aud supplied as agreed upon between the supplier and the
purchaser.
4. CLASSIFICATION
4.2 Non-load bearing lightweight concrete masonry units, hollow ( open
and closed cavity ) or solid shall be used in interior walls, partitions,
panels and for exterior panel walls in steel or reinforced concrete frame
construction when protected from weather by rendering or by some
other efbcient treatment.
5. MATERIALS
5.1 Cement - Cement complying with any of the following Indian
Standards may be used at the discretion of the manufacturer:
IS : 269-i976 Specification for ordinary and low heat Portland
cement ( third revision )
IS : 455-1976 Specification for Portland slag cement ( third revision )
7
9. IS 82185 ( Part II ) - 1983
1s : 1489-1976 Specification for Portland pozzolana cement ( second
revision )
IS : 6909- 1973 Specification for supersulphated cement
IS : 8041-1978 Specification for rapid hardening Portland cement
(Jir.~t revision )
IS : 8042-1978 Specification for white Portland cement (jrstrevision )
IS : 8043-1978 Specification for hydrophobic Portland cement (jir~t
revision )
5.1.1 When cement conforming to IS : 269-1976* is used, replacement
of cement by fly ash conforming to IS : 3812-1981t may be permitted up
to a limit of 20 percent. However, it shall be ensured that blending of
fly ash with cement is as intimate as possible, to achieve maximum
uniformity.
5.2 Lightweight Aggregates
5.2.1 The lightweight aggregates shall conform to IS : 9142-1979:.
The type of aggregate shall’ be approved by the purchaser. The
purchaser may also specify the use of a particular aggregate or a parti-
cular combination of aggregates.
5.2.2 The dry loose bulk density of the lightweight aggregates shall
be as follows:
Fine aggregate 1120 kg/m3, max
Coarse aggregate 880 kg/ms, max
Combined aggregate 1100 kg/ms, malr
5.3 Water - The water used in the manufacture of concrete masonry
units ihall be free from matter harmful to concrete or reinforcement, or
matter likely to cause efflorescence in the units. It shall conform to 4.3
of IS : 456-1978s.
5.4 Additives or Admixtures - Additives or admixtures may be
added either as additives to the cement during manufacture, or as admix-
tures to the concrete mix. Additives or admixtures used in the manufac-
ture of copcrete masonry units may be:
a) accelerating, water-reducing and air-entraining admixtures con-
forming to IS : 9103-197911,
b) colouring pigments,
*Specification for ordinary and low heat.Portland cement ( third retision ).
tspecification for flyash for use as pozzolana and admixture (Jirst revision ).
*Specification for artificial lightweight aggregates for concrete masonry units.
@ode of practice for plain and reinforced concrete ( third revision ).
IlSpecification for admixtures for concrete.
8
10. 15:2185(PartII)-1983
c) fly ash conforming to IS : 3812-1981*, and
d) waterproofing agents conforming to IS : 2645-1975t
Where no Indian Standards apply, the additives or admixtures shall
be shown by test or experience to be not deterimental to the durability
of the concrete.
6. MANUFACTURE
6.1 Mix - The concrete mix used for blocks shall not be richer than
one part by volume of cement to 6 parts of combined fine and coarse
aggregates as specified in 5.2. Allowance shall be made for bulking of
materials, if necessary.
6.2 Mixing - Concrete shall normally be mixed in a mechanical
mixer.
6.2.1 Mixing shall be continued until there is a uniform distribution of
the materials, and the mass is uniform in colour and consistency.
6.2.2 When hand mixing is permitted by the engineer-in-charge, it
shall be carried out on a water-tight platform and care shall be taken to
ensure that mixing is continued until the mass is uniform in colour and
consistency.
6.3 Placing and Compaction
6.3.1 In the case of hand-operated machine, the mixture shall be
placed into the mould in layers of about 50 to 75 mm and each layer
thoroughly tamped with suitable tampers until the whole mould is filled
up and struck off level with a trowel.
6.3.2 In the case of mechanically operated machine, the mould shall
be filled up to a height above the mould.appropriate to the machine
used, vibrated or mechanically tamped and struck off level.
6.3.3 Immediately the block is made, it shall be released from the
mould and removed with the pallet to a covered shed, to protect it
against sun and strong winds. The blocks shall be stored in the shed
until they are sufficiently hardeued to permit handling without damage
but in no case shall this period be less than 12 hours.
6.4 Curing
6.4.1 The blocks hardened in accordance with 6.3.3 shall then be
removed from the pallets and placed in a curing water tank or taken to
the curing yard ( see Note ), where these shall be kept continuously
-
*Specification for fly ash for use as pozzolana and admixture (Jrst reukion ).
tspecification for integral cement waterproofing compounds (first revision ).
9
11. IS : 2185 ( Part II ) - 1983
moist for at Ieast 21 days. When the blocks are cured in an immersion
tank, the water of the rank shall be changed at least every 4 days.
Nova - The curing yard is a paved yard subdivided by shallow drains into 4 to 5 m
square platforms which are provided with water fountains in the centre. The blocks
are stacked on the platforms around the fountains, which work continuously. The
fountains are connected to an elevated water storage tank.
6.4.2 St&am curing of blocks hardened in accordance with 6.3.3 may
be adopted instead of method specified in 6.4.1 provided the require-
ments of pressure or non-pressure steam curing are fulfilled. For non-
pressure steam curing, the blocks shall be subjected to the action of
thoroughly saturated steam at a temperature of 38” to 54°C for a period
of not less than 24 hours; or when necessary, for such additional time as
may be necessary to enable the blocks to meet the physical requirements
specified in this standard.
6.5 Drying - After curing the blocks shall be dried under shade for a
period of 4 weeks before being used on the work. They shall be stacked
with voids horizontal to facilita’te through passage of air. The blocks
shall be allowed to complete their initial shrinkage before they are laid
in a wall.
7. SURlJ.ACE TEXTURE AND FJ&ISH
7.1 Concrete masonry building units can be given a variety of surface
textures ranging from a very fine close texture to a coarse open texture
by proper selection, grading and proportioning of the aggregates at the
time of manufacture. Textures may also be developed by treating the
face of the units while still green by wire brushing or combing, by
slightly eroding the surface by playing a fine spray of water upon it,
and by splitting ( split block ). Colour may be introduced by. incorpo-
rating non-fading mineral pigments in the facing concrete, or by
applying a coloured Portland cement grout or paint to the face of the
units soon after they are removed from the moulds. Selected coloured
aggregates may also be used in the facing and exposed by washing with
water or dilute hydrochloric acid.
7.2 Concrete masonry units used in constructing exposed walls shall be
free from stains and discolouration, blemishes or defects which detract
the desired appearance of the finished wall.
8. PHYSICAL REQUIREMENTS
8.1 General - All units shall be sound and free of cracks or other
defects which interfere with the proper placing of the unit or impair the
strength or performance of the construction. Minor chipping resulting
from the customary methods of handling during delivery, shall not be
deemed grounds for rejection.
10
12. IS : 2185 ( Part II ) - 1983
8.1.1 Whereunits are to be used in exposed wall construction, the face
or faces that are to be exposed shall be free of chips, cracks, or other
imperfections, except that if not more than 5 percent of a consignment
contains slight cracks or small chippings not larger than 25 mm, this
shall not be deemed grounds for rejection.
8.2 Dimensions - The overall dimensions of the units when measured
as given in Appendix A shall be in accordance with 3 subject to the
tolerances mentioned therein.
8.3 Block Density - The block density, when determined as in
Appendix B, shall not exceed 1 600 kg/ma.
8.4 Compressive Strength - The minimum compressive strength,
being the average of eight units, and the minimum compressive strength
’
of individual units, when tested in the manner described in Appendix C,
shall be as prescribed in Table 1.
5.8 Water Absorption - The water absorption, being the average of
three units, when determined in the manner prescribed in Appendix D,
shall be as prescribed in Table 1.
TARLE 1 PHYSICAL REQUIREMENTS
TYPE AND GRADE
Hollow, load bearing
Grade A
Grade B
Hollow, non-load bear-
ing
Solid, load-bearing
Grade A
Grade B
MINIMUM COMPRESSIVE MAXIMUM AVERAGE WATER
STRENQTE ABSORPTIO~~,WITHOVEN-
DRY MASS OF CONCBETE
C_--_-h-___? __--*_-w-y
Average of Individual Less than Less than
8 units; Min unit, Min 1360 1600
(2) (3) (4) (5)
N/mm* N]mmz kg/m’ kg/m’
7’0 5.5 290
5.0 4.0 320 -
40 3.5 - i
12.5 1@8 - 290
8.5 7.0 320 -
8.6 Drying Shrinkage - The drying shrinkage of the units when
unrestrained being the average of three units, shall be determined in the
manner described in Appendix E, and shall be as follows:
a) Load-bearing light-weight concrete masonry units, hollow ( open
or closed cavity ) or solid,
11
13. IS I 2185 ( Part II ) - 1983
Grade A - 0’08 percent, max; and
Grade B - 0.09 percent, max
b> Non-load bearing Jigbt weight-O’09 percent, maxI
concrete masonry umtS
8.7 Moisture Movement - The moisture movement of the dried
blocks on immersion in water, being the average of three units, when
determined in the manner described in Appendix F, shall be less than
the drying shrinkage specified in 8.6 by at least 0.01.
9. TESTS
9.1 Tests as described in Appendix A to F shall be conducted on
samples of units selected according to the sampling procedure given in
10 to ensure conformity with the physical requirements laid down
in 8.
10. SAMPLING
10.1 The blocks required for carrying out the tests laid down in this
standard shall be taken by one of the methods given in 10.2 and 10.3.
In either case, a sample of 20 blocks shall be taken from every consign-
ment .of 5 008 blocks or part thereof of the same size and same hatch of
manufacture. From these samples, the blocks shall be taken at random
for conducting the tests.
10.2 Sampling Blocks in Motion - Whenever practicable, samples
of blocks shall be taken when the blocks are being moved as in the case
of loading, unloading, etc. The batch from where samples are to be
drawn shall be divided into a number of convenient portions such that
when one sample is drawn from each of these portions the minimum
number of blocks specified under 10.1 is provided.
10.3 Sampling Blocks from a Stack - The number of blocks
required for *he test shall be taken at random from across the top of
the stacks, the sides accessible and from the interior of the stacks by
opening trenches from the top.
10.4 Number of Tests
10.4.1 Ah the 20 blocks shall he checked for dimensions and inspected
for visual defects ( see8.1 and 8.2 ).
10.4.2 Out of the 20 blocks, 3 blocks shall be subjected to the test for
blocks density ( see 8.3 ), 8 blocks to the test for compressive strength
( see8.4 ), 3 blocks to the test for water absorption ( see8.3) and 3 blocks
to the test for drying shrinkage ( see8.6 ) and later to the test for moisture
movement. The remaining 3 bIocks shall be reserved for retest for
drying shrinkage and moisture movement if a need arises.
12
14. IS:2185(PartII)-1983
11. CRITERIA FOR CONFORMI-
11.1 The lot shell be considered as conforming to the requirements of
the specification if the conditions mentioned in 11.2 to Il.5 are satisfied.
11.2 The number of blocks with dimensions outside the tolerance limit
and/or with visual defects, among these inspected shall be not more than
two.
11.3 For block density, the mean value determined shall not be greater
than the maximum limit specified in 8.3.
11.4 For compressive strength, the mean value determined shall be
greater than or equal to the minimum limit s+zcified in 8.4
11.5 For drying shrinkage and moisture movement, all the test
specimens shall satisfy the requirements of the test. If one or more
specimens fail to satisfy the requirements, the remaining 3 blocks shall be
subjected to these tests. All these blocks shall satisfy the requirements.
11.6 For water absorption, the mean value determined shall be equal or
less than maximum limit specified in 8.5.
12. MANUFACTURER’8 CERTIFICATE
12.1 The manufacturer shall satisfy himself that the masonry units
conform to the requirements of this specification and, if requested, shall
supply a certificate to this effect to the purchaser or his representative.
13. INDEPENDENT TESTS
13.1 If the purchaser or his representative requires independent tests,
the samples shall be taken before or immediately after delivery, at the
option of the purchaser or his representative and the tests shall be carried
out in accordance with this specification.
13.2 The manufacturers shall supply free of charge the units required
for testing.
13.3 Cost of Testing - Unless otherwise specified in the enquiry 01
order, the cost of the tests shall be borne as follows:
a) By the manufacturer in the event of the results showing that the
blocks do not conform to this specification, or
b) By the purchaser in the event of the results showing that the
blocks conform to this specification.
13
15. IS.: 2185 ( Part II ) - 1983
14. MARKING
14.1 Concrete masonry units manufactured in accordance with this
specification shall be marked permanently with the following informa-
tion:
a) The identification of the manufacturer;
b) The grade of the unit; and
c) The year of manufacture, if required by the purchaser.
14.1.1 Each block may also be marked with the IS1 Ceriification
Mark.
NOTE - The use of the IS1 Certification Mark is governed by the provirions of the
Indian Standards Institution ( Certification Marks ) Act and the Rules and Regu-
lations made thereunder. The IS1 Mark on products covered by an Indian Standard
conveyr the assurance that they have been produced to comply with the require-
menta of that standard under a welldefined system of inspection, testing and quality
control which.ir devised and supervised by IS1 and operated by the producer. IS1
marked products are also continuously checked by ISI for conformity to that
standard 4 a further sa&guard. Details of conditions under which a licence for the
use of the IS1 Certi6cation Mark may be granted to manufacturers or procemors,
may be obtained from the Indian Standards Institution.
APPENDIX A
( Clauses 8.2 and 9.1 )
mASURElbf.ENT OF DIMENSIONS
A-l. APPARATUS
A-l.1 Overall dimensions shall be measured with a steel scale graduated
in 1 mm divisions. Face shell and web thickness shall be measured with
a caliper rule graduated in 0’5 mm divisions and having parallel jaw$
not less than 15 mm nor more than 25 mm in length.
A-2. SPECIMENS
A-2.1 Twenty full size units shall be measured for length, width and
height. Cored units shall also be measured for minimum thickness ef
face shells and webs.
NOTE - These specimens shall be used for other tests also.
A-3. MEASUREMENTS AND REPORT
A-3.1 Individual measurements of the dimensions of each unit shall be
read to the nearest division of the scale or caliper and the average
recorded.
14
16. IS : 2185( Part II ) - 1983
A-3.2 Length shall be measured on the longitudinal centre line of each
face, width across the top and bottom bearing surfaces at midlength,
and height on both faces at midlength. Face-shell thickness and web
thickness shall be measured at the thinnest point of each such element
15 mm above the mortar-bed plane. Where opposite face shells differ
in thickness by less than 3 mm, their measurements shall be averaged.
Sash grooves, dummy joints, and similar details shall be disregarded
in the measurements.
A-3.3 The report shall show the average length, width, and height of
each specimen, and the minimum face-shell and web thickness and total
web thickness in 200 mm length of walling per course as an average for
the 20 specimens.
APPENDIX B
( Clauses8.3 and 9.1 )
R4ETHODFOR THE DETERMINATION OF BLOCK DENSITY
B-l. PROCEDURE
B-l.1 Three blocks taken at random from the samples selected in
accordance with 10,shall be dried to a constant mass in a suitable oven
heated to approximately 100°C. After cooling the blocks to room
temperature, the dimensions of each block shall be measured in centi-
metres ( to the nearest millimetre ) and the overall volume computed
in cubic centimetres. The blocks shall then be weighed in kilograms
( to the nearest 10 g ) and the density of each block calculated as
follows:
Mass of block in kg
Density = -
Volume of specimen in cm<
x 10s kg/ma
B-1.2 The average for the three blocks shall be taken as the average
density.
APPENDIX C
( Clauses8.4 and 9.1 )
METHOD FOR THE DETERMINATION OF COMPRESSIVE
STRENGTH
C-l. APPARATUS
C-l.1 Testing Machine - The testing machine shall be equipped
with two steel bearing blocks ( see Note ) one of which is a spherically
15
17. IS : 2185 ( Part II ) - 1983
seated block that will transmit load to the upper surface of the masonry
specimen, and the other a plane rigid block on which the specimen will
rest. When the bearing area of the steel blocks is not sufficient to cover
the bearing area of the masonry specimen, steel bearing plates meeting
the requirements of C-I.2 shall be placed between the bearing blocks
and the capped specimen after the centroid of the masonry bearing
surface has been aligned with the centre of thrust of the bearing blocks
( seeC-41 ).
NOTE- It is desirable that the bearing faces of blocks and plates used fur comprer-
siontestingof concrete masonry have a hardness of not less than 60 ( HRC ).
c-1.2 Steel Bearing Blocks and Plates - The surfaces of the steel
bearing blocks and plates shall not depart from a plane by more than
O-025 mm in any 15 mm dimension. The centre of the sphere of the
spherically seated upper bearing block shall coincide with the centre of its
bearing face. If a bearing plate is used, the centre of the sphere of the
spherically seated bearing block shall lie on a line passing vertically
through the centroid of the specimen bearing face. The spherically
seated block shall be held closely in its seat, but shall be free to turn in
any direction. The diameter of the face of the bearing blocks shall be
at least 15 cm. When steel plates are employed between the steel bear-
ing blocks and the masonry specimen ( seeC-4.1 ) the plates shall have a
thickness equal to at least one-third of the distance from the edge of the
bearing block to the most distant corner of the specimen. In no case shall
the plate thickness be less than 12 mm.
C-2. TEST SPECIMENS
C-2.1 Eight full size units shall be tested within 72 hours after delivery
to the laboratory, during which time they shall be stored continuously
in normal room air.
C-2.2 Units of unusual size, shape, or strength may be sawed into
segments, some or all of which shall be tested individually in the same
manner as prescribed for full-size units. The strength of the full-size
units shall be considered as that which is calculated from the average
measured strength of the segments.
C-2.3 For the purpose of acceptance, age of testing the specimens shall
be 28 days. The age shall be reckoned from the time of the addition of
water to the dry ingredients.
C-3. CAPPING TEST SPECIMEN
C-3.0 Bearing surfaces of units shall be capped by one of the methods
described in C-3.1 and C-3.2.
C-3.1 Sulphur and Granular Materials - Proprietary or laboratory
prepared mixtures of 40 to 60 percent sulphur ( by mass ), the remainder
16
18. IS : 2185 ( Part g ) - 1983
being ground fire clay or other suitable inert material passing 150-micron
IS sieve with or without a plasticizer, shall be spread evenly on a non-
aborbent surface that has been lightly coated with oil ( seeNote ). The
sulphur mixture shall be heated in a thermostatically controlled heating
pot to a _temperature sufficient to maintain fluidity for a reasonable
period of time after contact with the capping surface. Care shall be
exercised to prevent overheating, and the liquid shall be stirred in the
pot just before use. The capping surface shall be plane within O-075 mm
in 40 cm and shall be sufficiently rigid and so supported as not to be
measurably deflected during the capping operation. Four 25 mm
square steel bars shall be placed on the surface plate to form a rectan-
gular mould approximately 12 mm greater in either inside dimension
than the masonry unit. The mould shall l+~ filled _to a depth of
6 mm with molten sulphur inaterial. The- surface of the unit to be
capped shall quickly be brought into contact with the liquid, and the
specimen, held so that its axis is at right angles to the surface of -the
capping liquid, shall be inserted. The unit shall be allowed to remain
undisturbed until solidification is complete. The caps shall be allowed
to cool for a minimum of 2 hours before the specimens are tested.
Patching of caps, shall not be permitted. Imperfect caps shall be
removed and replaced with new ones.
NOTE- The use of oil on capping plates may be omitted if it .i.i found that plate
and unit can be separated without damaging the cap.
C-33 Gypsum Plaster Capping - A neat paste of special high-
strength plaster ( see Note under C-4.1 ) and water shall be spread evenly
on a non-absorbent surface that has been lightly coated with oil. Such
gypsum plaster; when gauged with water & the capping consistency,
shall have a comnressive strength at a 2-liour age of not less than
25 N/mma, when iested as 50 mm cubes. The coat&g surface plate shall
conform to the requirements described in C-3.1. The surface of the unit
to be capped shall be brought into contact with the capping paste; the
specimen which is held with its axis at right angles to the capping
surface, shall be firmly pressed down with a single motion. The average
thickness of the cap shall be not more than 3 mm. Patching of caps shall
not be permitted. Imperfect caps shall be removed and replaced with
new ones. The caps shall be aged for at least 2 hours before the
specimens ate tested.
C-4. PROCEDURE
C-4.1 Position of Specimens - Specimens shall be tested with the
centroid of their bearing surfaces aligned vertically with the centre of
thrust of the spherically seated steel bearing block of the testing machine
( see Note ). Except for special units intended for use with their cores
in a horizontal direction, all hollow concrete masonry units shall be tested
with their cores in vertical direction. Masonry units that are 100
17
19. IS : 2185 (Pmt II ). - 1908
percent solid and special hollow units intended for use with their hollow
cores in a horizontal direction may he tested in the same direction as in
W!rvice.
NOTE- For homogenous materials. the centroid of the bearing surface shall be
considered w be vertically above the centre of gravity of the maronry unit.
C-4.2 Speed of Tehng -The load up to one-half of the expected
maximum load may be applied at any convenient rate, after which the
control of the machine shall be adjusted as required to give a uniform
rate of travel of the moving head such that the remaining load is applied
in not less than one nor more than two minutes.
C-5. CALCULATION AND REPORT
C-5.1 The compressive strength of a concrete masonry unit shall be taken
as the maximum load in Newtons divided by the gross cross-sectional
area of the unit in square millimetres. The gross area of a unit is the
total area of B section perpendicular to the direction of the load, includ-
ing dreas within cells and withiii re-entrant spaces unless these spaces
are to be occupied in the masonry by portions of adjacent masonry.
C-5.2 Report the results to the nearest 0-I N/mm8 separately for each
unit and as the average for the 8 units.
APPENDIX D
( Clauses8.5 and 9.1 )
METHOD FOR TEEE30~BEIIIIATION OF WATER
D-l. APPARATUS
D-1.1 The balance used shall be sensitive to within 0.5 percent of the
mass of the smalkst specimen tested.
D-1.2 Three full-size units shall be used.
D-2. PROCEDURE
D-2.1 Saturation - The test specimens shall be completely immersed
in water at room temperature for 24 hours. The specimens shall then
be weighed, while suspended by a metal wire and completely submerged
in water. . They shall be removed from the water and allowed to draifi
for one minute by placing them on a 10 mm or coarser wire mesh,
visible surface water being removed with a damp cloth, and immediately
weighed.
18
20. IS : 2185( Part II ) - 1983
D-2.2 Drying - Subsequent to saturation, all specimens shall be dried
in a ventilated oven at 100 to 115°C for not less than 24 hours and until
two successive weighings at intervals of 2 hours show an increment of
loss not greater than 0’2 percent of the last previously determined mass
of the specimen.
D-3. CALCULATION AND REPORT
D-3.1 Absorption - Calculate the absorption as follows:
A-B
Absorption, kg/m3 = A-_C x 1 000
Absorption, percent = LQE x 100
where
A,= wet mass of unit’in kg,
B = dry mass of unit in kg, and
C - suspended immersed mass of unit in kg.
D-3.2 Report - Report the results as the average for the three units.
APPENDIX E
( C2au.w 8.6 and 9.1 )
METHOD FOR THE DETERMiNATION OF DRYING
SHRINKAGE
E-l. NUMBER OF TESTS
E-l.1 Of the samples selected in accordance with 10, three shall be tested
for drying shrinkage. Three more blocks shall be set aside and stored
in air-tight containers at normal room temperature so as to be available
for duplicate tests if they are required at a later stage (see Note ).
NOTE - In order to facilitate storage, instead of blocks, sections cut from these
additional blocks may be stored until necessary in separate air-tight containers at
normal room temperature.
E-2. APPARATUS
E-2.1 Measuring Apparatus - A measuring apparatus shall be used
which incorporates a micrometer gauge or a suitable dial gauge reading
accurately to 0’002 5 mm. This gauge shall be rigidly mounted in a
19
21. IS : 2185 ( Part II ) - 1983
measuring frame and have a recessed end which may be located upon
a 5-mm diameter ball or other reference point cemented on the specimens.
The other end of the frame shall have a similar recessed seating which
may be locared upon the other .ball or reference point in the specimen. An
Invar steel rod of suitable length with 5-mm diameter hemispherical
ends or with 5-mm diameter steel balls mounted on the ends, shall be
used as a standard of length against which readings of the’ gauge may
be checked, thus enabling corrections to be made for any change in the
dimensions of the apparatus between successive measurements of a test
specimen. The apparatus shall preferably be adjusted for specimens of
different lengths and Invar rod of lengths near to those of the spejmens
to be tested shall be available.
E-2.2 Drying Oven - The drying oven shall comply with the following
requirements:
4
b)
It shall have an internal volume equivalent to not less than 8
Iitres per specimen, with a minimum total volume of 50 litres.
It shall be reasonably air-tight and shall be provided with a fan
to keep the air circulating effectively during the drying of the
specimen.
It shall be capable of maintaining a constant temperature of
50 f 1°C.
The relative humidity of the air in the oven shall be controlled
at approximately 17 percent by means of saturated calcium
chloride solution. Suitable dishes or trays containing this
solution shall be provided to give an exposed area of solution
not less than 10 cm2 for each litre of volume of the oven. The
dishes or trays shall contain sufficient solid calciuin chloride
to show above the surface of the solution throughout the test.
E-3. PREPARATION OF SPECIMENS
E-3.1 One sample shall be cut from each of the blocks such that the
length of each specimen is not less than 15 cm and the.cross-section is as
near to 7.5 x 7’5 cm as practicable in the case of solid blocks and
7.5 cm x thickness of the wall in the caseef other blocks. Two reference
points consisting of 5 mm diameter steel balls or dther suitable reference
points providing a hemispherical bearing shall be cemented with neat
rapid-hardening Portland cement or other suitable cementing material
at the centre of each end of each specimen after drilling or cutting a
shallow depression. After fixing, the surface of the steel balls shall be
wiped clean of cement, and dried and coated with lubricating grease to
prevent corrosion. The specimens shall then be’completely immersed in
water for 4 days, the temperature being.maintained at 27 f 2’C at least
for the last 4 hours.
20
22. IS : 2185 ( Part II ) - 1983
E-4. PROCEDURE FOR TESTING
E-4.1 Immediately after removal of the specimens from the water, the
grease shall be wiped from the steel balls and the length of each speci-
men measured to an accuracy of 0902 5 mm by the apparatus described
in E-2.1. This shall be taken as the original wet measurement.
NOTE - The instrument reading required is not the absolute length of the specimen
but the defference in length between the specimens and an Invar rod of approxima-
tely the same length.
E-4.2 The specimens shall then be dried for at least 44 hours in an oven
of the type described in E-2.2, at the specified temperature and humidity.
The specimens shall then be removed from the oven and cooled for at
least 4 hours in a desiccator containing solid calcium chloride or a
saturated solution of calcium chloride. Each specimen shall then be
measured as described in E-4.1, at a temperature of 27 & 2’C.
E-4.3 The cycle of drying, cooling and measuring shall be repeated until
constant length is attained, that is, when the difference between consecu-
tive readings separated by a period of drying of at least 44 hours followed
by cooling for at least 4 hours, is less than 0905 mm for a 15 cm
specimen and pro rata for a larger specimen. The final reading shall be
taken as the dry measurement.
E-4.4 During the above drying process further wet specimen shall not
be placed in the same oven and there shall be free access of air to all
surfaces of the specimen.
E-4.5 After the dry measurement has been taken, the length of the
specimen shall be measured, adjacent to the steel balls, to the nearest
millimetre and this shall be taken as the ‘dry length’.
E-5. CALCULATION OF RESULTS
E-5.1 The ‘drying shrinkage’ shall be calculated for each specimen as the
difference between the ‘original wet measurement’ and the ‘dry measure-
ment’ expressed as a percentage of the ‘dry length’.
E-5.2 Report all results separately for each unit.
21
23. IS : 2185 ( Part II ) - 1983
APPENDIX F
( Clauses 8.7 and 9.1 >
METHOD FOR THE DETERMINATION OF MOISTURE
MOVEMENT
F-I. PROCEDURE
F-l.1 The specimens which have previously been used for the drying
shrinkage test ( see Appendix E ) shall after the completion of that test,
be immersed in water for 4 days, the temperature being maintained at
27 f 2°C for at least 4 hours prior to the removal of the specimens and
the wet length measured. The moisture movement shall be determined
as the difference between the dry and wet lengths and expressed as a
percentage of the dry length for each specimen.
F-1.2 Should the value obtained with any one of the three specimens
tested be greater than the limit specified in 8.7, the test shall be repeated
on the further three blocks which were set aside. In repeating the
moisture movement test, the drying shrinkage test shall be repeated if the
previous speoimens have failed on that test also; otherwise, the drying
shrinkage test may be omitted. The three new specimens, in that
event, shall be dried to constant length at 50 f 1°C measured after
cooling and the moisture movement test carried out as described
in F-1.1.
22
24. IS : 2185 ( Part II ) - 1983
1 Continued from page 2 )
Precast Concrete Products Subcommittee, BDC 2 : 9
Convener
SRRI G. K. MAJUMDAR
Members
Representing
Hindustan Prefab Ltd, New Delhi
DEPUTY DIRECTOR, STANDARDS Research_, Designs & Standards Organization,
(B&S) ( Ministry of Railways )
ASSISTANT DIRECTOR, STAN-
DARDS ( B & S ) II ( Alternate )
DIRECTOR Central Soil & Materials Research Station,
New Delhi
DEPUTY DIRECTOR ( Alternate )
SHRI Z. GEORGE Structural Engineering Research Centre ( CSIR ),
Madras
DR A. G. MlDHAVA R-40 ( Alternate )
SIIRI V. G. GOKHALE Bombay Chemicals Pvt Ltd, Bombay
SHRI B. K. JINDAL Central Building Research Institute ( CSIR ),
Roorkee
DR S. S. REHSI f Alternate 1
’
I
SHRI L. C. LA1
SHRI S. NAIIEREY
In personal capacity ( B/17, West l&d, New Delhi )
Engineering Construction Corporation Ltd. Madras
S~rirr A. RAWAKRISHXA ( Alternate-) -
SHRID. B. NAIK
SHRI S~CHA SINCI~( Alternate)
Engineer-in-Cheif’s Branch, Army Headquarters
SHHI K. K. NA~~BIAR In personal capacity ( ‘Ramanalaya , I1 First Crescent
SHRI B. V. B. PA1
Park Road, Gandhinagar, Adyar, Madras )
The Concrete Association of India, Bombay
SHRI P. SRINIVASAN ( Alternate )
SERI H. S. PASRICHA Hindustan Prefab Ltd, New Delhi
DR N. RAOHAVENDRA Cement Research Institute of India, New Delhi
SHRI V. RAMALINQAM Neyveli Lignite Corporation Ltd, Neyveli
SHRI K. A. RAMABRADRAN ( Alternate )
DRA.V.R.RAO National Buildings Organization, New Delhi
SHRI J. SEN GUPTA ( Alternate )
SHRI B. G. SHIRKE B. G. Shirke & Co Pvt Ltd. Pune
SHRI U. S. DURGAKERI ( Alternate )
SHRI C. N. SRINIVASAN C. R. Narayana Rao, Madras
SHRI C. N. RA~HAVENDRAN ( Alternate )
SUP~XINTENDIN~ ENGINEER Tamil Nadu Hotsing Board, Madras
(P&S)
PROJECT OFFICER ( Alternate )
SCPERINTENDI~Q SURVEYOR OF Central Public Works Department
Wonlis ( NZ )
SURVEYOR OF WORKS ( NZ ) ( Alhwxzfe )
23