This document summarizes a study on the effect of sulphuric acid in water on the strength of blended cement concrete. Concrete cubes were produced using mixing and curing water with varying concentrations of sulphuric acid from 100-900 mg/L. The compressive strengths at 28 and 90 days were evaluated and decreased with increasing acid concentration. Regression models were developed that can predict the compressive strength based on the sulphuric acid concentration in water. The setting times of the blended cement also increased significantly with concentrations over 300 mg/L. In conclusion, higher sulphuric acid concentrations in water were found to reduce the strength of blended cement concrete.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
Curing Methods and Their Effects on The Strength of ConcreteIJERA Editor
There are a lot of arguments on which method of curing concrete gives good strength. These different opinions results into this study, which aim at investigating the effects of different curing methods on the strength of concrete. Laboratory test was employed for this study. Normal concretes were prepared using specified mix ratio of 1:2:4 and 1:3:6. The cubes tested for compressive strength at 3, 7, 21, and 28 days of curing respectively using four curing methods namely immersion, sprinkling, polythene sheeting and sharp sand coating. Testing indicate that water immersion curing method as well as sprinkling (spraying ) methods of curing, provide better results than membrane (polythene sheeting) method of curing. While sharp sand gives least strength. The rate of drying was significant when the specimens were subjected to curing with polythene sheet method of curing. This thus hampered the hydration process and thus affected the compressive strength property of the hardened concrete. The overall findings of this study suggests that concrete should be cured by water immersion or spraying regularly to achieve a better compressive strength in concrete.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
Curing Methods and Their Effects on The Strength of ConcreteIJERA Editor
There are a lot of arguments on which method of curing concrete gives good strength. These different opinions results into this study, which aim at investigating the effects of different curing methods on the strength of concrete. Laboratory test was employed for this study. Normal concretes were prepared using specified mix ratio of 1:2:4 and 1:3:6. The cubes tested for compressive strength at 3, 7, 21, and 28 days of curing respectively using four curing methods namely immersion, sprinkling, polythene sheeting and sharp sand coating. Testing indicate that water immersion curing method as well as sprinkling (spraying ) methods of curing, provide better results than membrane (polythene sheeting) method of curing. While sharp sand gives least strength. The rate of drying was significant when the specimens were subjected to curing with polythene sheet method of curing. This thus hampered the hydration process and thus affected the compressive strength property of the hardened concrete. The overall findings of this study suggests that concrete should be cured by water immersion or spraying regularly to achieve a better compressive strength in concrete.
This research represents an experimental study on influence of urea on concrete through various tests on urea, cement, concrete and water. Test of finesses modulus, slump test, carbonation test, pH test, urea ingression test and increase in strength with urea percentage .This study deals to overcome three major problems in the concrete namely heat of hydration, permeability, and corrosion of steel bar embedded in concrete. Urea can generally reduce the temperature of concrete both at casting phase and during the procedure of hydration. Urea does not opposite effect the durability of reinforced concrete, except where there is an accumulation of urea crystal growth. Er. Babita | Mr. Ravi Prakash Sharma | Mr. Vikram | Dr. D. K. Gupta ""Influence of Urea on Concrete"" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-4 | Issue-2 , February 2020,
URL: https://www.ijtsrd.com/papers/ijtsrd30172.pdf
Paper Url : https://www.ijtsrd.com/engineering/civil-engineering/30172/influence-of-urea-on-concrete/er-babita
This paper presents the findings of an investigation on the compressive strength of concrete containing
Groundnut Husk Ash (GHA) blended with Rice Husk Ash (RHA) and its resistance to acid aggression, as well
as regression models of the concrete resistance in acidic environment. The GHA and RHA used were obtained
by controlled burning of groundnut husk and rice husk, respectively in a kiln to a temperature of 600 oC, and
after allowing cooling, sieved through sieve 75 µm and characterized. The compressive strength of GHA-RHAConcrete
was investigated at replacement levels of 0, 10, 20, 30 and 40 %, respectively by weight of cement. A
total of seventy five 150 mm cubes of GHA-RHA-Concrete grade 20 were tested for compressive strength at 3,
7, 28, 60 and 90 days of curing. Also, thirty 100 mm cubes were exposed to attack from 10 % concentration of
diluted solution of sulphuric acid (H2SO4) and nitric acid (HNO3), respectively and the concrete resistance was
also modeled using Minitab statistical software to establish regression models. The result of the investigations
showed that the compressive strength of the concrete decreased with increase in GHA-RHA content. However
15 % replacement with GHA-RHA was considered as optimum for structural concrete. The use of GHA
admixed with 10 % RHA in concrete improved its resistance against sulphuric and nitric acids aggression. The
average weight loss of GHA-RHA- concrete after 28 days of exposure in sulphuric acid and nitric acid were
11.6 % and 11.7 %, respectively as opposed to 22.4 % and 15.1 %, respectively for plain Portland cement
concrete. The regression models of GHA-RHA-Concrete for resistance against sulphuric and nitric acids were
developed with R2
values of 0.668 and 0.655, respectively and were adequate for prediction of the sensitivities
of pozzolanic activity of GHA-RHA in acidic environment.
EXPERIMENTAL INVESTIGATION ON USAGE OF GREY WATER IN CONCRETE PRODUCTIONAbdulRazakBH
Abstract - An experimental study has been carried out to study the workability and strength behavior of concrete made using grey water and conventional concrete both in fresh and hardened states. To conduct the study, treated water from a treatment plant at two different stages of treatment has been collected and its effect on workability and strength of a mix M20 was studied. Workability was checked by slump and compaction factor method for each set of preparation of the samples. Strength behavior was studied with reference to compression strength, split tensile strength and flexural strength of the concrete specimens by destructive methods. The result confirms that the use of secondary treated water will not alter fresh and hardened properties of the concrete significantly when compared with that prepared with potable water. The study also concludes that there may be possibilities of corrosion of reinforcement due to the organic and inorganic impurities present in the grey water. Hence concrete made using grey water is suitable for plain concrete. Key Words: Grey Water, Manufactured sand
A Review On Development Of Flyash Based High Strength Geopolymer Concretecedmmantc5411
Geopolymer concrete is the latest development in the field of concrete technology and it is still
developing. Geopolymers are inorganic, stable, hard and non-inflammable binder. The application of
geopolymer binder are in fire resistance fiber composite, sealant industry, tooling aeronautics SPF aluminium,
foundry equipment’s, radioactive toxic waste, ceramic, bricks and other precast concrete. The current review is
aims to put forward the development in geopolymer concrete for the production high strength geopolymer
concrete having strength more than 90MPa. The development of high strength concrete is aimed to reduce
structural member sizes and for economical construction in case of long span bridges and tall buildings. Also
the use flyash in concrete to reduce green gas house emission into the atmosphere by reducing cement usage
COMPRESSIVE STRENGTH AND CARBONATION OF SEA WATER CURED BLENDED CONCRETE IAEME Publication
This paper investigates the influence of sea water on pre-cast concrete containing
industrial by-product materials such as fly ash (FA) and silpozz. The mix design is targeted for
M30 grade concrete. Ten concrete mixtures were designed to have the same degree of
workability with water to cementitious material ratio of 0.43. The studied parameters include
the compressive strength of normal water curing (NWC) and sea water curing (SWC) samples
after 28 days of NWC for 7, 28, 90, 180 and 365 days curing period. The carbonation depth of
concrete samples for 28, 90, 180 and 365 days SWC after 28 days of NWC was measured. It
was found that the higher the FA content the higher is the carbonation process occurred. The
percentage increase in compressive strength for blended cement concrete in NWC is better
than the samples in SWC after 28 days of NWC
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
Effect of Replacement of Cement by Different Pozzolanic Materials on Heat of ...Agriculture Journal IJOEAR
The paper aims to focus on the possibility of using industrial by products like SF, GGBS, FA and MK. The utilization of pozzolans is well accepted because of several improvements possible in the concrete composites. The present study reports the results of experimental study conducted to evaluate Setting Time, HOH and Compression Strength of Concrete, by partially replacing cement by various percentages of silica fume (SF), ground granulated blast furnace slag (GGBS), fly ash (FA) and metakaolin (MK) (5%, 10%, 15%, & 20%). The Heat of Hydration (HOH) and Compression Strength test are done for M30 grade concrete. The effort is made towards a specific understanding of efficiency of pozzolans in concrete considering the percentage of replacement and combinations of pozzolans. The pozzolans replacement as cementitious material is characterised by high compressive strength, low heat of hydration and increased initial and final setting time of concrete.
This research represents an experimental study on influence of urea on concrete through various tests on urea, cement, concrete and water. Test of finesses modulus, slump test, carbonation test, pH test, urea ingression test and increase in strength with urea percentage .This study deals to overcome three major problems in the concrete namely heat of hydration, permeability, and corrosion of steel bar embedded in concrete. Urea can generally reduce the temperature of concrete both at casting phase and during the procedure of hydration. Urea does not opposite effect the durability of reinforced concrete, except where there is an accumulation of urea crystal growth. Er. Babita | Mr. Ravi Prakash Sharma | Mr. Vikram | Dr. D. K. Gupta ""Influence of Urea on Concrete"" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-4 | Issue-2 , February 2020,
URL: https://www.ijtsrd.com/papers/ijtsrd30172.pdf
Paper Url : https://www.ijtsrd.com/engineering/civil-engineering/30172/influence-of-urea-on-concrete/er-babita
This paper presents the findings of an investigation on the compressive strength of concrete containing
Groundnut Husk Ash (GHA) blended with Rice Husk Ash (RHA) and its resistance to acid aggression, as well
as regression models of the concrete resistance in acidic environment. The GHA and RHA used were obtained
by controlled burning of groundnut husk and rice husk, respectively in a kiln to a temperature of 600 oC, and
after allowing cooling, sieved through sieve 75 µm and characterized. The compressive strength of GHA-RHAConcrete
was investigated at replacement levels of 0, 10, 20, 30 and 40 %, respectively by weight of cement. A
total of seventy five 150 mm cubes of GHA-RHA-Concrete grade 20 were tested for compressive strength at 3,
7, 28, 60 and 90 days of curing. Also, thirty 100 mm cubes were exposed to attack from 10 % concentration of
diluted solution of sulphuric acid (H2SO4) and nitric acid (HNO3), respectively and the concrete resistance was
also modeled using Minitab statistical software to establish regression models. The result of the investigations
showed that the compressive strength of the concrete decreased with increase in GHA-RHA content. However
15 % replacement with GHA-RHA was considered as optimum for structural concrete. The use of GHA
admixed with 10 % RHA in concrete improved its resistance against sulphuric and nitric acids aggression. The
average weight loss of GHA-RHA- concrete after 28 days of exposure in sulphuric acid and nitric acid were
11.6 % and 11.7 %, respectively as opposed to 22.4 % and 15.1 %, respectively for plain Portland cement
concrete. The regression models of GHA-RHA-Concrete for resistance against sulphuric and nitric acids were
developed with R2
values of 0.668 and 0.655, respectively and were adequate for prediction of the sensitivities
of pozzolanic activity of GHA-RHA in acidic environment.
EXPERIMENTAL INVESTIGATION ON USAGE OF GREY WATER IN CONCRETE PRODUCTIONAbdulRazakBH
Abstract - An experimental study has been carried out to study the workability and strength behavior of concrete made using grey water and conventional concrete both in fresh and hardened states. To conduct the study, treated water from a treatment plant at two different stages of treatment has been collected and its effect on workability and strength of a mix M20 was studied. Workability was checked by slump and compaction factor method for each set of preparation of the samples. Strength behavior was studied with reference to compression strength, split tensile strength and flexural strength of the concrete specimens by destructive methods. The result confirms that the use of secondary treated water will not alter fresh and hardened properties of the concrete significantly when compared with that prepared with potable water. The study also concludes that there may be possibilities of corrosion of reinforcement due to the organic and inorganic impurities present in the grey water. Hence concrete made using grey water is suitable for plain concrete. Key Words: Grey Water, Manufactured sand
A Review On Development Of Flyash Based High Strength Geopolymer Concretecedmmantc5411
Geopolymer concrete is the latest development in the field of concrete technology and it is still
developing. Geopolymers are inorganic, stable, hard and non-inflammable binder. The application of
geopolymer binder are in fire resistance fiber composite, sealant industry, tooling aeronautics SPF aluminium,
foundry equipment’s, radioactive toxic waste, ceramic, bricks and other precast concrete. The current review is
aims to put forward the development in geopolymer concrete for the production high strength geopolymer
concrete having strength more than 90MPa. The development of high strength concrete is aimed to reduce
structural member sizes and for economical construction in case of long span bridges and tall buildings. Also
the use flyash in concrete to reduce green gas house emission into the atmosphere by reducing cement usage
COMPRESSIVE STRENGTH AND CARBONATION OF SEA WATER CURED BLENDED CONCRETE IAEME Publication
This paper investigates the influence of sea water on pre-cast concrete containing
industrial by-product materials such as fly ash (FA) and silpozz. The mix design is targeted for
M30 grade concrete. Ten concrete mixtures were designed to have the same degree of
workability with water to cementitious material ratio of 0.43. The studied parameters include
the compressive strength of normal water curing (NWC) and sea water curing (SWC) samples
after 28 days of NWC for 7, 28, 90, 180 and 365 days curing period. The carbonation depth of
concrete samples for 28, 90, 180 and 365 days SWC after 28 days of NWC was measured. It
was found that the higher the FA content the higher is the carbonation process occurred. The
percentage increase in compressive strength for blended cement concrete in NWC is better
than the samples in SWC after 28 days of NWC
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
Effect of Replacement of Cement by Different Pozzolanic Materials on Heat of ...Agriculture Journal IJOEAR
The paper aims to focus on the possibility of using industrial by products like SF, GGBS, FA and MK. The utilization of pozzolans is well accepted because of several improvements possible in the concrete composites. The present study reports the results of experimental study conducted to evaluate Setting Time, HOH and Compression Strength of Concrete, by partially replacing cement by various percentages of silica fume (SF), ground granulated blast furnace slag (GGBS), fly ash (FA) and metakaolin (MK) (5%, 10%, 15%, & 20%). The Heat of Hydration (HOH) and Compression Strength test are done for M30 grade concrete. The effort is made towards a specific understanding of efficiency of pozzolans in concrete considering the percentage of replacement and combinations of pozzolans. The pozzolans replacement as cementitious material is characterised by high compressive strength, low heat of hydration and increased initial and final setting time of concrete.
Евгений Павленко – практикующий инженер и эксперт по технологиям Microsoft – о начале работы с Active Directory Domain Services и том, как эта технология позволяет упростить работу сетевого администратора.
Influence of alkaline substances (carbonates and bicarbonates of sodium) in w...eSAT Journals
Abstract The impurities in water play a major role in application of concrete. This paper assesses the setting times and compressive strength of natural admixture cements and silica fume is used as an admixture. This study introduces the effect of strong alkalines (carbonates and bicarbonates of sodium) on setting time and compressive strength of natural admixture cements (PPC+SF) is assessed under laboratory conditions. The research programme included tests of soundness, setting times, compressive strength of short and long term and powdered x-ray diffraction analysis. As the experimental results show that Na2CO3 in deionised water accelerates the intial and final setting times where as the other compound NaHCO3 retards the intial and final setting times for all concentrations. Na2CO3 and NaHCO3 in deionised water increase the compressive strength at early age (3-day and 7-day) and decrease significantly from28-day, 60-day, 90-day, 180-day, 1year and 2years.Comparison of the strong alkaline substances with those of control mix levels that both carbonates decrease compressive strength. The rate of decrease is increasing with increase in concentration .The present work analyses the hydration characteristics of admixture cement using X-ray diffraction analysis (XRD) and useful conclusions are obtained regarding the influence of alkaline substances. Key words: PPC, Silica fume, setting times, strength development, X-ray diffraction
Influence of alkaline substances (carbonates and bicarbonates of sodium) in w...eSAT Publishing House
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology.
Statistical Evaluation of Mechanical Strengths of Salt-Water Concreteinventionjournals
An evaluation of the salt water from River Ovum in Ebony State, Nigeria, was carried to ascertain its suitability as mixing water for concrete production. The chemical analysis showed that the dissolved solids (1300 mg/l), alkalinity (4.1 ppm), and other impurities, are within acceptable limits for mixing water for concrete production. The salt water used as mixing water in cement paste and concrete, showed no adverse effect on the setting times. The cube compressive strength at 7 days (92 %) is above the acceptable limit of 91 %. The compressive strength ratio to flexural strength for both fresh and salt water is approximately 4 and regression models developed for both compressive and flexural strengths are statistically adequate.
STUDY ON BEHAVIOR OF ALKALI ACTIVATED FLYASH BASED GEOPOLYMER CONCRETEIAEME Publication
Objectives: This study is to identify the effect of parameter such as Activator ratio that affects the properties of alkali activated fly ash-based geopolymer concrete.
Methodology: To achieve the above objectives, the present investigation is adopted a technology that is currently in use to manufacture and to test the conventional concrete. The main aim of this activity was to facilitate promotion of new materials later on to the concrete industry. Research variable included activator ratio (1:2, 1:2.5, and 1:3). The trial mix is prepared for the molarity of 16 M. Concrete specimens were cured at room temperature. The response variables are Flexural strength, Compressive strength and Split tensile strength.
Findings: Test data are used to identify the variation of Geopolymer concrete properties which are affected by using of various activator ratios and curing period. At all ages, the activator ratio 1:3 gives maximum strength and also economical when compared to other two activator ratios. There is substantial gain in compressive strength of fly ash based geopolymer concrete with age.
Improvements: This work can be enhanced for various molarities under various temperatures and various activator ratios.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
Locally available Red soil were used for the experimental analysis to study the
effects of seawater impact in concrete structures with comparison of normal water in
terms of its strength properties and changes on the behavior of Red soil. M-20 & M-
30 concrete cubes were casted with 0.45 water-cement ratio. Casted Concrete cubes
are buried in red Soil near Costal zone to observe the Compressive strength and NDT
during 28th day and 84th day with addition of fly ash class-C of two different
proportions 20% & 30%. Totally 72 specimen were cast with normal water. The
highest value of compressive strength obtained is 35.13N/Sq.mm during 84th day for
Seawater curing in addition of fly ash class-C and lowest value is 15.57N/Sq.mm
during 84th day for seawater curing without fly ash
Fly Ash as a Partial Replacement of Cement in Concrete and Durability Study o...IJERD Editor
Cement production gives rise to CO2emissions generated by the calcinations of CaCo3 and by the
fossil, being responsible for about 5% of the Co2 emissions in the world. This can be substantially reduced if
cement replacement materials such as a fly ash are used Within the frame work of a comprehensive research
concerning this residual of coal industries, studied some durability characteristics of concretes made with Fly
ash. In this project report the results of the tests carried out on Sulphate attack on concrete cubes in water curing
along with H2SO4 solution. Also, aiming the use of fly-ash as cement replacement. The present experimental
investigation were carried on fly ash and has been chemically and physically characterized, and partially
replaced in the ratio of 0%, 5%, 10%, 15%, 20% by weight of cement in concrete. Fresh concrete tests like
compaction factor test was hardened concrete tests like compressive Strength at the age of 28 days, 60 days, 90
days was obtained and also durability aspect of fly ash concrete for sulphates attack was tested. The result
indicates that fly ash improves concrete durability.
The purpose of the present paper is to study the changes in the strength characteristics of
autoclaved aerated concrete (AAC) and also the density when different expansion agents are used. The
expansion agent so used releases air in the concrete thereby making it lighter by reducing its density. It
also increases the workability of the concrete. The various air entraining agents used for this study are
hydrogen peroxide, oleic acid and olive oil. The addition of these agents causes the concrete to rise like
cake but it reduces the strength of concrete due to the formation of air voids. The amount of agents
chosen for concrete production are 0.5%, 1%, 1.5% by weight of cement.
International Journal of Computational Engineering Research(IJCER) is an intentional online Journal in English monthly publishing journal. This Journal publish original research work that contributes significantly to further the scientific knowledge in engineering and Technology
journal publishing, how to publish research paper, Call For research paper, international journal, publishing a paper, IJERD, journal of science and technology, how to get a research paper published, publishing a paper, publishing of journal, publishing of research paper, reserach and review articles, IJERD Journal, How to publish your research paper, publish research paper, open access engineering journal, Engineering journal, Mathemetics journal, Physics journal, Chemistry journal, Computer Engineering, Computer Science journal, how to submit your paper, peer reviw journal, indexed journal, reserach and review articles, engineering journal, www.ijerd.com, research journals,
yahoo journals, bing journals, International Journal of Engineering Research and Development, google journals, hard copy of journal
Submission Deadline: 30th September 2022
Acceptance Notification: Within Three Days’ time period
Online Publication: Within 24 Hrs. time Period
Expected Date of Dispatch of Printed Journal: 5th October 2022
MODELING AND ANALYSIS OF SURFACE ROUGHNESS AND WHITE LATER THICKNESS IN WIRE-...IAEME Publication
White layer thickness (WLT) formed and surface roughness in wire electric discharge turning (WEDT) of tungsten carbide composite has been made to model through response surface methodology (RSM). A Taguchi’s standard Design of experiments involving five input variables with three levels has been employed to establish a mathematical model between input parameters and responses. Percentage of cobalt content, spindle speed, Pulse on-time, wire feed and pulse off-time were changed during the experimental tests based on the Taguchi’s orthogonal array L27 (3^13). Analysis of variance (ANOVA) revealed that the mathematical models obtained can adequately describe performance within the parameters of the factors considered. There was a good agreement between the experimental and predicted values in this study.
A STUDY ON THE REASONS FOR TRANSGENDER TO BECOME ENTREPRENEURSIAEME Publication
The study explores the reasons for a transgender to become entrepreneurs. In this study transgender entrepreneur was taken as independent variable and reasons to become as dependent variable. Data were collected through a structured questionnaire containing a five point Likert Scale. The study examined the data of 30 transgender entrepreneurs in Salem Municipal Corporation of Tamil Nadu State, India. Simple Random sampling technique was used. Garrett Ranking Technique (Percentile Position, Mean Scores) was used as the analysis for the present study to identify the top 13 stimulus factors for establishment of trans entrepreneurial venture. Economic advancement of a nation is governed upon the upshot of a resolute entrepreneurial doings. The conception of entrepreneurship has stretched and materialized to the socially deflated uncharted sections of transgender community. Presently transgenders have smashed their stereotypes and are making recent headlines of achievements in various fields of our Indian society. The trans-community is gradually being observed in a new light and has been trying to achieve prospective growth in entrepreneurship. The findings of the research revealed that the optimistic changes are taking place to change affirmative societal outlook of the transgender for entrepreneurial ventureship. It also laid emphasis on other transgenders to renovate their traditional living. The paper also highlights that legislators, supervisory body should endorse an impartial canons and reforms in Tamil Nadu Transgender Welfare Board Association.
BROAD UNEXPOSED SKILLS OF TRANSGENDER ENTREPRENEURSIAEME Publication
Since ages gender difference is always a debatable theme whether caused by nature, evolution or environment. The birth of a transgender is dreadful not only for the child but also for their parents. The pain of living in the wrong physique and treated as second class victimized citizen is outrageous and fully harboured with vicious baseless negative scruples. For so long, social exclusion had perpetuated inequality and deprivation experiencing ingrained malign stigma and besieged victims of crime or violence across their life spans. They are pushed into the murky way of life with a source of eternal disgust, bereft sexual potency and perennial fear. Although they are highly visible but very little is known about them. The common public needs to comprehend the ravaged arrogance on these insensitive souls and assist in integrating them into the mainstream by offering equal opportunity, treat with humanity and respect their dignity. Entrepreneurship in the current age is endorsing the gender fairness movement. Unstable careers and economic inadequacy had inclined one of the gender variant people called Transgender to become entrepreneurs. These tiny budding entrepreneurs resulted in economic transition by means of employment, free from the clutches of stereotype jobs, raised standard of living and handful of financial empowerment. Besides all these inhibitions, they were able to witness a platform for skill set development that ignited them to enter into entrepreneurial domain. This paper epitomizes skill sets involved in trans-entrepreneurs of Thoothukudi Municipal Corporation of Tamil Nadu State and is a groundbreaking determination to sightsee various skills incorporated and the impact on entrepreneurship.
DETERMINANTS AFFECTING THE USER'S INTENTION TO USE MOBILE BANKING APPLICATIONSIAEME Publication
The banking and financial services industries are experiencing increased technology penetration. Among them, the banking industry has made technological advancements to better serve the general populace. The economy focused on transforming the banking sector's system into a cashless, paperless, and faceless one. The researcher wants to evaluate the user's intention for utilising a mobile banking application. The study also examines the variables affecting the user's behaviour intention when selecting specific applications for financial transactions. The researcher employed a well-structured questionnaire and a descriptive study methodology to gather the respondents' primary data utilising the snowball sampling technique. The study includes variables like performance expectations, effort expectations, social impact, enabling circumstances, and perceived risk. Each of the aforementioned variables has a major impact on how users utilise mobile banking applications. The outcome will assist the service provider in comprehending the user's history with mobile banking applications.
ANALYSE THE USER PREDILECTION ON GPAY AND PHONEPE FOR DIGITAL TRANSACTIONSIAEME Publication
Technology upgradation in banking sector took the economy to view that payment mode towards online transactions using mobile applications. This system enabled connectivity between banks, Merchant and user in a convenient mode. there are various applications used for online transactions such as Google pay, Paytm, freecharge, mobikiwi, oxygen, phonepe and so on and it also includes mobile banking applications. The study aimed at evaluating the predilection of the user in adopting digital transaction. The study is descriptive in nature. The researcher used random sample techniques to collect the data. The findings reveal that mobile applications differ with the quality of service rendered by Gpay and Phonepe. The researcher suggest the Phonepe application should focus on implementing the application should be user friendly interface and Gpay on motivating the users to feel the importance of request for money and modes of payments in the application.
VOICE BASED ATM FOR VISUALLY IMPAIRED USING ARDUINOIAEME Publication
The prototype of a voice-based ATM for visually impaired using Arduino is to help people who are blind. This uses RFID cards which contain users fingerprint encrypted on it and interacts with the users through voice commands. ATM operates when sensor detects the presence of one person in the cabin. After scanning the RFID card, it will ask to select the mode like –normal or blind. User can select the respective mode through voice input, if blind mode is selected the balance check or cash withdraw can be done through voice input. Normal mode procedure is same as the existing ATM.
IMPACT OF EMOTIONAL INTELLIGENCE ON HUMAN RESOURCE MANAGEMENT PRACTICES AMONG...IAEME Publication
There is increasing acceptability of emotional intelligence as a major factor in personality assessment and effective human resource management. Emotional intelligence as the ability to build capacity, empathize, co-operate, motivate and develop others cannot be divorced from both effective performance and human resource management systems. The human person is crucial in defining organizational leadership and fortunes in terms of challenges and opportunities and walking across both multinational and bilateral relationships. The growing complexity of the business world requires a great deal of self-confidence, integrity, communication, conflict and diversity management to keep the global enterprise within the paths of productivity and sustainability. Using the exploratory research design and 255 participants the result of this original study indicates strong positive correlation between emotional intelligence and effective human resource management. The paper offers suggestions on further studies between emotional intelligence and human capital development and recommends for conflict management as an integral part of effective human resource management.
VISUALISING AGING PARENTS & THEIR CLOSE CARERS LIFE JOURNEY IN AGING ECONOMYIAEME Publication
Our life journey, in general, is closely defined by the way we understand the meaning of why we coexist and deal with its challenges. As we develop the "inspiration economy", we could say that nearly all of the challenges we have faced are opportunities that help us to discover the rest of our journey. In this note paper, we explore how being faced with the opportunity of being a close carer for an aging parent with dementia brought intangible discoveries that changed our insight of the meaning of the rest of our life journey.
A STUDY ON THE IMPACT OF ORGANIZATIONAL CULTURE ON THE EFFECTIVENESS OF PERFO...IAEME Publication
The main objective of this study is to analyze the impact of aspects of Organizational Culture on the Effectiveness of the Performance Management System (PMS) in the Health Care Organization at Thanjavur. Organizational Culture and PMS play a crucial role in present-day organizations in achieving their objectives. PMS needs employees’ cooperation to achieve its intended objectives. Employees' cooperation depends upon the organization’s culture. The present study uses exploratory research to examine the relationship between the Organization's culture and the Effectiveness of the Performance Management System. The study uses a Structured Questionnaire to collect the primary data. For this study, Thirty-six non-clinical employees were selected from twelve randomly selected Health Care organizations at Thanjavur. Thirty-two fully completed questionnaires were received.
Living in 21st century in itself reminds all of us the necessity of police and its administration. As more and more we are entering into the modern society and culture, the more we require the services of the so called ‘Khaki Worthy’ men i.e., the police personnel. Whether we talk of Indian police or the other nation’s police, they all have the same recognition as they have in India. But as already mentioned, their services and requirements are different after the like 26th November, 2008 incidents, where they without saving their own lives has sacrificed themselves without any hitch and without caring about their respective family members and wards. In other words, they are like our heroes and mentors who can guide us from the darkness of fear, militancy, corruption and other dark sides of life and so on. Now the question arises, if Gandhi would have been alive today, what would have been his reaction/opinion to the police and its functioning? Would he have some thing different in his mind now what he had been in his mind before the partition or would he be going to start some Satyagraha in the form of some improvement in the functioning of the police administration? Really these questions or rather night mares can come to any one’s mind, when there is too much confusion is prevailing in our minds, when there is too much corruption in the society and when the polices working is also in the questioning because of one or the other case throughout the India. It is matter of great concern that we have to thing over our administration and our practical approach because the police personals are also like us, they are part and parcel of our society and among one of us, so why we all are pin pointing towards them.
A STUDY ON TALENT MANAGEMENT AND ITS IMPACT ON EMPLOYEE RETENTION IN SELECTED...IAEME Publication
The goal of this study was to see how talent management affected employee retention in the selected IT organizations in Chennai. The fundamental issue was the difficulty to attract, hire, and retain talented personnel who perform well and the gap between supply and demand of talent acquisition and retaining them within the firms. The study's main goals were to determine the impact of talent management on employee retention in IT companies in Chennai, investigate talent management strategies that IT companies could use to improve talent acquisition, performance management, career planning and formulate retention strategies that the IT firms could use. The respondents were given a structured close-ended questionnaire with the 5 Point Likert Scale as part of the study's quantitative research design. The target population consisted of 289 IT professionals. The questionnaires were distributed and collected by the researcher directly. The Statistical Package for Social Sciences (SPSS) was used to collect and analyse the questionnaire responses. Hypotheses that were formulated for the various areas of the study were tested using a variety of statistical tests. The key findings of the study suggested that talent management had an impact on employee retention. The studies also found that there is a clear link between the implementation of talent management and retention measures. Management should provide enough training and development for employees, clarify job responsibilities, provide adequate remuneration packages, and recognise employees for exceptional performance.
ATTRITION IN THE IT INDUSTRY DURING COVID-19 PANDEMIC: LINKING EMOTIONAL INTE...IAEME Publication
Globally, Millions of dollars were spent by the organizations for employing skilled Information Technology (IT) professionals. It is costly to replace unskilled employees with IT professionals possessing technical skills and competencies that aid in interconnecting the business processes. The organization’s employment tactics were forced to alter by globalization along with technological innovations as they consistently diminish to remain lean, outsource to concentrate on core competencies along with restructuring/reallocate personnel to gather efficiency. As other jobs, organizations or professions have become reasonably more appropriate in a shifting employment landscape, the above alterations trigger both involuntary as well as voluntary turnover. The employee view on jobs is also afflicted by the COVID-19 pandemic along with the employee-driven labour market. So, having effective strategies is necessary to tackle the withdrawal rate of employees. By associating Emotional Intelligence (EI) along with Talent Management (TM) in the IT industry, the rise in attrition rate was analyzed in this study. Only 303 respondents were collected out of 350 participants to whom questionnaires were distributed. From the employees of IT organizations located in Bangalore (India), the data were congregated. A simple random sampling methodology was employed to congregate data as of the respondents. Generating the hypothesis along with testing is eventuated. The effect of EI and TM along with regression analysis between TM and EI was analyzed. The outcomes indicated that employee and Organizational Performance (OP) were elevated by effective EI along with TM.
INFLUENCE OF TALENT MANAGEMENT PRACTICES ON ORGANIZATIONAL PERFORMANCE A STUD...IAEME Publication
By implementing talent management strategy, organizations would have the option to retain their skilled professionals while additionally working on their overall performance. It is the course of appropriately utilizing the ideal individuals, setting them up for future top positions, exploring and dealing with their performance, and holding them back from leaving the organization. It is employee performance that determines the success of every organization. The firm quickly obtains an upper hand over its rivals in the event that its employees having particular skills that cannot be duplicated by the competitors. Thus, firms are centred on creating successful talent management practices and processes to deal with the unique human resources. Firms are additionally endeavouring to keep their top/key staff since on the off chance that they leave; the whole store of information leaves the firm's hands. The study's objective was to determine the impact of talent management on organizational performance among the selected IT organizations in Chennai. The study recommends that talent management limitedly affects performance. On the off chance that this talent is appropriately management and implemented properly, organizations might benefit as much as possible from their maintained assets to support development and productivity, both monetarily and non-monetarily.
A STUDY OF VARIOUS TYPES OF LOANS OF SELECTED PUBLIC AND PRIVATE SECTOR BANKS...IAEME Publication
Banking regulations act of India, 1949 defines banking as “acceptance of deposits for the purpose of lending or investment from the public, repayment on demand or otherwise and withdrawable through cheques, drafts order or otherwise”, the major participants of the Indian financial system are commercial banks, the financial institution encompassing term lending institutions. Investments institutions, specialized financial institution and the state level development banks, non banking financial companies (NBFC) and other market intermediaries such has the stock brokers and money lenders are among the oldest of the certain variants of NBFC and the oldest market participants. The asset quality of banks is one of the most important indicators of their financial health. The Indian banking sector has been facing severe problems of increasing Non- Performing Assets (NPAs). The NPAs growth directly and indirectly affects the quality of assets and profitability of banks. It also shows the efficiency of banks credit risk management and the recovery effectiveness. NPA do not generate any income, whereas, the bank is required to make provisions for such as assets that why is a double edge weapon. This paper outlines the concept of quality of bank loans of different types like Housing, Agriculture and MSME loans in state Haryana of selected public and private sector banks. This study is highlighting problems associated with the role of commercial bank in financing Small and Medium Scale Enterprises (SME). The overall objective of the research was to assess the effect of the financing provisions existing for the setting up and operations of MSMEs in the country and to generate recommendations for more robust financing mechanisms for successful operation of the MSMEs, in turn understanding the impact of MSME loans on financial institutions due to NPA. There are many research conducted on the topic of Non- Performing Assets (NPA) Management, concerning particular bank, comparative study of public and private banks etc. In this paper the researcher is considering the aggregate data of selected public sector and private sector banks and attempts to compare the NPA of Housing, Agriculture and MSME loans in state Haryana of public and private sector banks. The tools used in the study are average and Anova test and variance. The findings reveal that NPA is common problem for both public and private sector banks and is associated with all types of loans either that is housing loans, agriculture loans and loans to SMES. NPAs of both public and private sector banks show the increasing trend. In 2010-11 GNPA of public and private sector were at same level it was 2% but after 2010-11 it increased in many fold and at present there is GNPA in some more than 15%. It shows the dark area of Indian banking sector.
EXPERIMENTAL STUDY OF MECHANICAL AND TRIBOLOGICAL RELATION OF NYLON/BaSO4 POL...IAEME Publication
An experiment conducted in this study found that BaSO4 changed Nylon 6's mechanical properties. By changing the weight ratios, BaSO4 was used to make Nylon 6. This Researcher looked into how hard Nylon-6/BaSO4 composites are and how well they wear. Experiments were done based on Taguchi design L9. Nylon-6/BaSO4 composites can be tested for their hardness number using a Rockwell hardness testing apparatus. On Nylon/BaSO4, the wear behavior was measured by a wear monitor, pinon-disc friction by varying reinforcement, sliding speed, and sliding distance, and the microstructure of the crack surfaces was observed by SEM. This study provides significant contributions to ultimate strength by increasing BaSO4 content up to 16% in the composites, and sliding speed contributes 72.45% to the wear rate
ROLE OF SOCIAL ENTREPRENEURSHIP IN RURAL DEVELOPMENT OF INDIA - PROBLEMS AND ...IAEME Publication
The majority of the population in India lives in villages. The village is the back bone of the country. Village or rural industries play an important role in the national economy, particularly in the rural development. Developing the rural economy is one of the key indicators towards a country’s success. Whether it be the need to look after the welfare of the farmers or invest in rural infrastructure, Governments have to ensure that rural development isn’t compromised. The economic development of our country largely depends on the progress of rural areas and the standard of living of rural masses. Village or rural industries play an important role in the national economy, particularly in the rural development. Rural entrepreneurship is based on stimulating local entrepreneurial talent and the subsequent growth of indigenous enterprises. It recognizes opportunity in the rural areas and accelerates a unique blend of resources either inside or outside of agriculture. Rural entrepreneurship brings an economic value to the rural sector by creating new methods of production, new markets, new products and generate employment opportunities thereby ensuring continuous rural development. Social Entrepreneurship has the direct and primary objective of serving the society along with the earning profits. So, social entrepreneurship is different from the economic entrepreneurship as its basic objective is not to earn profits but for providing innovative solutions to meet the society needs which are not taken care by majority of the entrepreneurs as they are in the business for profit making as a sole objective. So, the Social Entrepreneurs have the huge growth potential particularly in the developing countries like India where we have huge societal disparities in terms of the financial positions of the population. Still 22 percent of the Indian population is below the poverty line and also there is disparity among the rural & urban population in terms of families living under BPL. 25.7 percent of the rural population & 13.7 percent of the urban population is under BPL which clearly shows the disparity of the poor people in the rural and urban areas. The need to develop social entrepreneurship in agriculture is dictated by a large number of social problems. Such problems include low living standards, unemployment, and social tension. The reasons that led to the emergence of the practice of social entrepreneurship are the above factors. The research problem lays upon disclosing the importance of role of social entrepreneurship in rural development of India. The paper the tendencies of social entrepreneurship in India, to present successful examples of such business for providing recommendations how to improve situation in rural areas in terms of social entrepreneurship development. Indian government has made some steps towards development of social enterprises, social entrepreneurship, and social in- novation, but a lot remains to be improved.
OPTIMAL RECONFIGURATION OF POWER DISTRIBUTION RADIAL NETWORK USING HYBRID MET...IAEME Publication
Distribution system is a critical link between the electric power distributor and the consumers. Most of the distribution networks commonly used by the electric utility is the radial distribution network. However in this type of network, it has technical issues such as enormous power losses which affect the quality of the supply. Nowadays, the introduction of Distributed Generation (DG) units in the system help improve and support the voltage profile of the network as well as the performance of the system components through power loss mitigation. In this study network reconfiguration was done using two meta-heuristic algorithms Particle Swarm Optimization and Gravitational Search Algorithm (PSO-GSA) to enhance power quality and voltage profile in the system when simultaneously applied with the DG units. Backward/Forward Sweep Method was used in the load flow analysis and simulated using the MATLAB program. Five cases were considered in the Reconfiguration based on the contribution of DG units. The proposed method was tested using IEEE 33 bus system. Based on the results, there was a voltage profile improvement in the system from 0.9038 p.u. to 0.9594 p.u.. The integration of DG in the network also reduced power losses from 210.98 kW to 69.3963 kW. Simulated results are drawn to show the performance of each case.
APPLICATION OF FRUGAL APPROACH FOR PRODUCTIVITY IMPROVEMENT - A CASE STUDY OF...IAEME Publication
Manufacturing industries have witnessed an outburst in productivity. For productivity improvement manufacturing industries are taking various initiatives by using lean tools and techniques. However, in different manufacturing industries, frugal approach is applied in product design and services as a tool for improvement. Frugal approach contributed to prove less is more and seems indirectly contributing to improve productivity. Hence, there is need to understand status of frugal approach application in manufacturing industries. All manufacturing industries are trying hard and putting continuous efforts for competitive existence. For productivity improvements, manufacturing industries are coming up with different effective and efficient solutions in manufacturing processes and operations. To overcome current challenges, manufacturing industries have started using frugal approach in product design and services. For this study, methodology adopted with both primary and secondary sources of data. For primary source interview and observation technique is used and for secondary source review has done based on available literatures in website, printed magazines, manual etc. An attempt has made for understanding application of frugal approach with the study of manufacturing industry project. Manufacturing industry selected for this project study is Mahindra and Mahindra Ltd. This paper will help researcher to find the connections between the two concepts productivity improvement and frugal approach. This paper will help to understand significance of frugal approach for productivity improvement in manufacturing industry. This will also help to understand current scenario of frugal approach in manufacturing industry. In manufacturing industries various process are involved to deliver the final product. In the process of converting input in to output through manufacturing process productivity plays very critical role. Hence this study will help to evolve status of frugal approach in productivity improvement programme. The notion of frugal can be viewed as an approach towards productivity improvement in manufacturing industries.
A MULTIPLE – CHANNEL QUEUING MODELS ON FUZZY ENVIRONMENTIAEME Publication
In this paper, we investigated a queuing model of fuzzy environment-based a multiple channel queuing model (M/M/C) ( /FCFS) and study its performance under realistic conditions. It applies a nonagonal fuzzy number to analyse the relevant performance of a multiple channel queuing model (M/M/C) ( /FCFS). Based on the sub interval average ranking method for nonagonal fuzzy number, we convert fuzzy number to crisp one. Numerical results reveal that the efficiency of this method. Intuitively, the fuzzy environment adapts well to a multiple channel queuing models (M/M/C) ( /FCFS) are very well.
Kubernetes & AI - Beauty and the Beast !?! @KCD Istanbul 2024Tobias Schneck
As AI technology is pushing into IT I was wondering myself, as an “infrastructure container kubernetes guy”, how get this fancy AI technology get managed from an infrastructure operational view? Is it possible to apply our lovely cloud native principals as well? What benefit’s both technologies could bring to each other?
Let me take this questions and provide you a short journey through existing deployment models and use cases for AI software. On practical examples, we discuss what cloud/on-premise strategy we may need for applying it to our own infrastructure to get it to work from an enterprise perspective. I want to give an overview about infrastructure requirements and technologies, what could be beneficial or limiting your AI use cases in an enterprise environment. An interactive Demo will give you some insides, what approaches I got already working for real.
Connector Corner: Automate dynamic content and events by pushing a buttonDianaGray10
Here is something new! In our next Connector Corner webinar, we will demonstrate how you can use a single workflow to:
Create a campaign using Mailchimp with merge tags/fields
Send an interactive Slack channel message (using buttons)
Have the message received by managers and peers along with a test email for review
But there’s more:
In a second workflow supporting the same use case, you’ll see:
Your campaign sent to target colleagues for approval
If the “Approve” button is clicked, a Jira/Zendesk ticket is created for the marketing design team
But—if the “Reject” button is pushed, colleagues will be alerted via Slack message
Join us to learn more about this new, human-in-the-loop capability, brought to you by Integration Service connectors.
And...
Speakers:
Akshay Agnihotri, Product Manager
Charlie Greenberg, Host
Software Delivery At the Speed of AI: Inflectra Invests In AI-Powered QualityInflectra
In this insightful webinar, Inflectra explores how artificial intelligence (AI) is transforming software development and testing. Discover how AI-powered tools are revolutionizing every stage of the software development lifecycle (SDLC), from design and prototyping to testing, deployment, and monitoring.
Learn about:
• The Future of Testing: How AI is shifting testing towards verification, analysis, and higher-level skills, while reducing repetitive tasks.
• Test Automation: How AI-powered test case generation, optimization, and self-healing tests are making testing more efficient and effective.
• Visual Testing: Explore the emerging capabilities of AI in visual testing and how it's set to revolutionize UI verification.
• Inflectra's AI Solutions: See demonstrations of Inflectra's cutting-edge AI tools like the ChatGPT plugin and Azure Open AI platform, designed to streamline your testing process.
Whether you're a developer, tester, or QA professional, this webinar will give you valuable insights into how AI is shaping the future of software delivery.
Key Trends Shaping the Future of Infrastructure.pdfCheryl Hung
Keynote at DIGIT West Expo, Glasgow on 29 May 2024.
Cheryl Hung, ochery.com
Sr Director, Infrastructure Ecosystem, Arm.
The key trends across hardware, cloud and open-source; exploring how these areas are likely to mature and develop over the short and long-term, and then considering how organisations can position themselves to adapt and thrive.
Encryption in Microsoft 365 - ExpertsLive Netherlands 2024Albert Hoitingh
In this session I delve into the encryption technology used in Microsoft 365 and Microsoft Purview. Including the concepts of Customer Key and Double Key Encryption.
Essentials of Automations: Optimizing FME Workflows with ParametersSafe Software
Are you looking to streamline your workflows and boost your projects’ efficiency? Do you find yourself searching for ways to add flexibility and control over your FME workflows? If so, you’re in the right place.
Join us for an insightful dive into the world of FME parameters, a critical element in optimizing workflow efficiency. This webinar marks the beginning of our three-part “Essentials of Automation” series. This first webinar is designed to equip you with the knowledge and skills to utilize parameters effectively: enhancing the flexibility, maintainability, and user control of your FME projects.
Here’s what you’ll gain:
- Essentials of FME Parameters: Understand the pivotal role of parameters, including Reader/Writer, Transformer, User, and FME Flow categories. Discover how they are the key to unlocking automation and optimization within your workflows.
- Practical Applications in FME Form: Delve into key user parameter types including choice, connections, and file URLs. Allow users to control how a workflow runs, making your workflows more reusable. Learn to import values and deliver the best user experience for your workflows while enhancing accuracy.
- Optimization Strategies in FME Flow: Explore the creation and strategic deployment of parameters in FME Flow, including the use of deployment and geometry parameters, to maximize workflow efficiency.
- Pro Tips for Success: Gain insights on parameterizing connections and leveraging new features like Conditional Visibility for clarity and simplicity.
We’ll wrap up with a glimpse into future webinars, followed by a Q&A session to address your specific questions surrounding this topic.
Don’t miss this opportunity to elevate your FME expertise and drive your projects to new heights of efficiency.
Neuro-symbolic is not enough, we need neuro-*semantic*Frank van Harmelen
Neuro-symbolic (NeSy) AI is on the rise. However, simply machine learning on just any symbolic structure is not sufficient to really harvest the gains of NeSy. These will only be gained when the symbolic structures have an actual semantics. I give an operational definition of semantics as “predictable inference”.
All of this illustrated with link prediction over knowledge graphs, but the argument is general.
GDG Cloud Southlake #33: Boule & Rebala: Effective AppSec in SDLC using Deplo...James Anderson
Effective Application Security in Software Delivery lifecycle using Deployment Firewall and DBOM
The modern software delivery process (or the CI/CD process) includes many tools, distributed teams, open-source code, and cloud platforms. Constant focus on speed to release software to market, along with the traditional slow and manual security checks has caused gaps in continuous security as an important piece in the software supply chain. Today organizations feel more susceptible to external and internal cyber threats due to the vast attack surface in their applications supply chain and the lack of end-to-end governance and risk management.
The software team must secure its software delivery process to avoid vulnerability and security breaches. This needs to be achieved with existing tool chains and without extensive rework of the delivery processes. This talk will present strategies and techniques for providing visibility into the true risk of the existing vulnerabilities, preventing the introduction of security issues in the software, resolving vulnerabilities in production environments quickly, and capturing the deployment bill of materials (DBOM).
Speakers:
Bob Boule
Robert Boule is a technology enthusiast with PASSION for technology and making things work along with a knack for helping others understand how things work. He comes with around 20 years of solution engineering experience in application security, software continuous delivery, and SaaS platforms. He is known for his dynamic presentations in CI/CD and application security integrated in software delivery lifecycle.
Gopinath Rebala
Gopinath Rebala is the CTO of OpsMx, where he has overall responsibility for the machine learning and data processing architectures for Secure Software Delivery. Gopi also has a strong connection with our customers, leading design and architecture for strategic implementations. Gopi is a frequent speaker and well-known leader in continuous delivery and integrating security into software delivery.
Elevating Tactical DDD Patterns Through Object CalisthenicsDorra BARTAGUIZ
After immersing yourself in the blue book and its red counterpart, attending DDD-focused conferences, and applying tactical patterns, you're left with a crucial question: How do I ensure my design is effective? Tactical patterns within Domain-Driven Design (DDD) serve as guiding principles for creating clear and manageable domain models. However, achieving success with these patterns requires additional guidance. Interestingly, we've observed that a set of constraints initially designed for training purposes remarkably aligns with effective pattern implementation, offering a more ‘mechanical’ approach. Let's explore together how Object Calisthenics can elevate the design of your tactical DDD patterns, offering concrete help for those venturing into DDD for the first time!
Securing your Kubernetes cluster_ a step-by-step guide to success !KatiaHIMEUR1
Today, after several years of existence, an extremely active community and an ultra-dynamic ecosystem, Kubernetes has established itself as the de facto standard in container orchestration. Thanks to a wide range of managed services, it has never been so easy to set up a ready-to-use Kubernetes cluster.
However, this ease of use means that the subject of security in Kubernetes is often left for later, or even neglected. This exposes companies to significant risks.
In this talk, I'll show you step-by-step how to secure your Kubernetes cluster for greater peace of mind and reliability.