1) What is the difference between CSMA/CD and CSMA/CA
2) Which of the following is a form of Ethernet that is transmitted over Fiber Optics
3) You’re setting up a network at an engineering office where very large files are going to move back and forth over the network all day long, day in and day out. Which of the following devices is more likely to avoid a lot of network congestion?
4) A router operates at the ____________ layer of the OSI model.
5) Which of the OSI layers interprets an IP address?
6) How does Exponential backoff work.
7) A collision on an Ethernet network occurs when ______________.
8) In the above illustrated IP address, if this were a Class B address, which of the four octets would be part of the network address?
9) Describe how CSMA/CD works.
10) RIP is a form of _______________ protocol.
11) You have a Class C TCP/IP network. You are using the default subnet mask. What is the maximum number of hosts you can have on your network?
12) Which Networking hardware protocol utilizes CSMA/CD media access methods?
1) FDDI uses a ___________ topology
2) 15.46.86.101 is a ________________ IP address.
3) What is the difference between RTZ and AMI signaling.
4) Which network topology requires that a terminator be installed at both ends of the network?
1) IPX/SPX uses a ____________ -bit network address.
2) The proper default subnet mask for a Class A network is 255.255.0.0.
1) Why is CRC a better error detection method than checksum
2) Which of the following is NOT something DHCP can automaticall configure.
3) The HTTP protocol uses port 80 on a typical Windows machine
4) TCP/IP Version 6 uses a _____________ -bit address.
5) Which of the following OSI layers breaks the user data down into smaller chunks for transmission onto the network?
1) The protocol that is used for outgoing email messages is usually _____________.
...
Đề tieng anh thpt 2024 danh cho cac ban hoc sinh
1) What is the difference between CSMACD and CSMACA2) Which .docx
1. 1) What is the difference between CSMA/CD and CSMA/CA
2) Which of the following is a form of Ethernet that is
transmitted over Fiber Optics
3) You’re setting up a network at an engineering office where
very large files are going to move back and forth over the
network all day long, day in and day out. Which of the
following devices is more likely to avoid a lot of network
congestion?
4) A router operates at the ____________ layer of the OSI
model.
5) Which of the OSI layers interprets an IP address?
6) How does Exponential backoff work.
7) A collision on an Ethernet network occurs when
______________.
8) In the above illustrated IP address, if this were a Class B
address, which of the four octets would be part of the network
address?
9) Describe how CSMA/CD works.
10) RIP is a form of _______________ protocol.
11) You have a Class C TCP/IP network. You are using the
default subnet mask. What is the maximum number of hosts you
can have on your network?
12) Which Networking hardware protocol utilizes CSMA/CD
media access methods?
1) FDDI uses a ___________ topology
2) 15.46.86.101 is a ________________ IP address.
3) What is the difference between RTZ and AMI signaling.
4) Which network topology requires that a terminator be
installed at both ends of the network?
1) IPX/SPX uses a ____________ -bit network address.
2) The proper default subnet mask for a Class A network is
2. 255.255.0.0.
1) Why is CRC a better error detection method than checksum
2) Which of the following is NOT something DHCP can
automaticall configure.
3) The HTTP protocol uses port 80 on a typical Windows
machine
4) TCP/IP Version 6 uses a _____________ -bit address.
5) Which of the following OSI layers breaks the user data down
into smaller chunks for transmission onto the network?
1) The protocol that is used for outgoing email messages is
usually _____________.
