This resume is for Dinesh Kumar Sarda, an electrical engineer seeking a position utilizing his technical and manufacturing experience. He has over 3 years of experience as an Assistant Manager at JAYASWAL NECO INDUSTRIES LIMITED, where he maintains electrical systems including a 69 MW power plant. His responsibilities include electrical design, installation, maintenance, and project management. He holds a B.Tech in electrical engineering and has experience with software like MS Office and operating systems like Windows.

1. RESUME
DINESH KUMAR SARDA
Permanent Address: Email ID: dsarda.rec@gmail.com
C/O Mr.Kishore Bajaj, Contact No: 7566983348
H NO:26,New Panchsheel Nagar,Civil lines,
Raipur –492001,Chhattisgarh.
Career Objective:
To work as an electrical engineer in project management and electrical designing utilising technical
engineering background and manufacturing experience contributing to company’s growth and in turn
ensuring personal growth within the organization.
Work Experience: Three years, 4 months and continuing.
Designation: Assistant Manager.
Employer: JAYASWAL NECO INDUSTRIES LIMITED(Raipur, Chhattisgarh)
One year of extensive training in captive power plant- net capacity of 69 MW (including both AFBC and
WHRB type boiler {utilizing waste heat of Direct Reduced Iron and Blast Furnace })
Part of Power Management System (PMS) project {PLC :PAC RX3i by General Electricals Intelligent
platform based on GE Proficy Machine Edition 2007 logic developer & Cimplicity (SCADA)} and currently
looking after the maintenance of Main Receiving Sub Station (220 kV and 132 kV).
Job Responsibilities:
 Reading Electrical Drawings, Planning of Projects, Erection & Maintenance.
 Short circuit calculation.
 Earth bus calculations and sizing
 Hazardous area classification.
 Sizing of Cables, Generator, Motor, Transformer, LT & HT Breaker.
 Preparation of Single Line Diagram.
 Preparation of cable route drawings.
 Preparation of technical specifications for Transformer, HT Breaker, LT panel.
 Preparation of cost estimate & bill of Material for electrical work.
 Technical Bid analysis for material & service contracts.
 Installation, testing & commissioning of LT & HT equipments like Transformer, HT Breaker,Motor,
Generator.
 Co ordination with electrical contractors during execution of electrical work.
 Relay co-ordination.
 Inspection of material at vendor’s / Manufacturer’s site.

2.  Responsible for all the switching operations and maintenance of LT and HT motors(up to 375KW),
ACB(L&T 415V),VCB(SIEMENS 6.6KV&11KV,AREVA 6.6 KV& 33KV,GEC ALSTHOM 6.6KV) and SF6
breakers(CROMPTON GREAVES 132KV, KIRLOSKAR 33KV& SIEMENS 220KV&132KV) CT&PT( both
outdoor and indoor type), UPS, Battery Bank, Isolators, Power & Distribution transformers(up to 120
MVA),Generator LAPT and NGR and AVR panel, distribution board lighting systems, cabling and control
wiring.
 Planning and conducting effective shut down and preventive maintenance, overhauling, repair schedule,
of various machineries and instrument to increase system up time and long term system reliability,as per
ISO 9001-2008 norms.
 Handling Management Information System (MIS) reports as well as maintaining spares.
 Ferruling,luging,tagging,wiring of control cables in the PLC, CONTROL DESK and H.T FEEDERS (220 Kv,132
kv,33Kv, 11Kv and 6.6Kv).Tray work, cable laying, dressing, gland termination as per the prescribed
schedule.
 Testing and installation of Analog (disk and induction type), Overload electronic relays as well as
microprocessor based relays (MICOM series- 120,122,&341,632 SIEMENS 7UT61,
7SJ61,7SJ62,7SJ8031&7SJ8011); used in generator,motor,feeder and transformer protection.
 Ensuring 100% plant load factor and housekeeping using 5S.
 Operation and maintenance of starters (DOL, R-DOL and STAR-DELTA) and its feeder wiring including
energy meters and trivector meters.
 To conduct Synchronization of generator & feeder breakers when needed.
 Calculating overall plant generation, maintaining export and import data ,energy balance report and
CAR(corrective action report).
 To conduct Fault Level Calculation for different bus bars to know the fault level current and decide the
suitable breaker ratings, as well as relay coordination.

3. CAT 2013 score: 80.28 percentile
Examination
Passed
Year of
passing
Name of Board/University
School/College
Studied
B.Tech(E.E.E) 2010
Biju Pattnaik University Of
Technology(B.P.U.T)
Raajdhani Engineering
College(Bhubaneswar)
Class XII(H.S.C) 2005 I.S.C ST.Joseph’s Convent
High School(Sambalpur) 61.20%
Class X(S.S.C) 2003 I.C.S.E ST.Joseph’s Convent
High School(Sambalpur) 64.80%
Projects done:
 Errection, Commissioning & testing of “SYNCHRONISING PANEL” for 6.6KV breaker.
Percentage Scored
7.25 CGPA
 Errection, Commissioning & testing of “33 KV BREAKER CONTROL AND RELAY PANEL CUM TAP
CHANGER” for 16 MVA TRANSFORMER.
Software Skills:
 Operating Systems : Windows 2007/XP
 Package : MS Office 2007
Strengths:
Self-confident, Optimistic with good communication skills, Determined, Patient, believe in Hard Work. I have
a quest and zeal to learn new technologies.
Hobbies:
Like to play Chess, Swimming, Cooking, listening to music, watching movies, visiting new places and
interacting with new people.