The document provides an overview of the total textile finishing process. It discusses various finishing machines and their functions, including squeezers, slitting machines, stenter machines, tube compactors, open width compactors, and raising machines. It also covers different types of finishing processes like softening, stiffening, antimicrobial finishing, UV protection, fireproofing, and nano-finishing. The document includes machine parameters, process flow charts, and development points for quality control.
(Over Dyeing) to dye for a second or third time with a different color. Over dyeing is such a rewarding way of rescuing an ugly or unsatisfactory colored cloth. It gives uneven look. sometimes over dyeing doesn’t mean all-time dyeing the garment which is previously dyed. Over dyeing may be normal dyeing or piece dyeing process.
The term finishing, in a broad sense it covers all the processes of making the fabric good looking, good hand feeling, luster and of course for buyer requirement. It is done after dying and before delivery to market. Various types of parameters are controlled during finishing section considering buyer requirement. The term also includes bleaching, dyeing, mercerizing etc. But normally the term is restricted to the final stage in the sequence of treatment of Knit fabrics after bleaching and dyeing. However, fabrics which are neither bleached nor dyed are also finished.
(Over Dyeing) to dye for a second or third time with a different color. Over dyeing is such a rewarding way of rescuing an ugly or unsatisfactory colored cloth. It gives uneven look. sometimes over dyeing doesn’t mean all-time dyeing the garment which is previously dyed. Over dyeing may be normal dyeing or piece dyeing process.
The term finishing, in a broad sense it covers all the processes of making the fabric good looking, good hand feeling, luster and of course for buyer requirement. It is done after dying and before delivery to market. Various types of parameters are controlled during finishing section considering buyer requirement. The term also includes bleaching, dyeing, mercerizing etc. But normally the term is restricted to the final stage in the sequence of treatment of Knit fabrics after bleaching and dyeing. However, fabrics which are neither bleached nor dyed are also finished.
A machine or apparatus for stretching or stentering fabrics. The purpose of the Stenter machine is to bringing the length and width to pre determine dimensions and also for heat setting and it is used for applying finishing chemicals and also shade variation is adjusted. The main function of the Stenter is to stretch the fabric widthwise and to recover the uniform width.
Fabric Compacting Process and Compacting MachinesRakin Rasheed
A small presentation on Compacting Process which is the most important mechanical finishing process for knitted fabric to control GSM, width, shrinkage etc according to the buyer requirement.
A machine or apparatus for stretching or stentering fabrics. The purpose of the Stenter machine is to bringing the length and width to pre determine dimensions and also for heat setting and it is used for applying finishing chemicals and also shade variation is adjusted. The main function of the Stenter is to stretch the fabric widthwise and to recover the uniform width.
Fabric Compacting Process and Compacting MachinesRakin Rasheed
A small presentation on Compacting Process which is the most important mechanical finishing process for knitted fabric to control GSM, width, shrinkage etc according to the buyer requirement.
Now Knit RMG (Ready made garment) is the highest foreign currency earning sector of Bangladesh. For knit fabric processing its involves many chemical process, so drying is an important operation. The production of various mechanical finishes on knitted fabric involve conditioning of the material to a certain moisture content and then drying by different means.
This presentation is my graduation internship presentation at BSL (LNJ group) Bhilwara (Rajasthan).
In this presentation I describe BSL company profile, Process significance, all steps which use for fibre to fabric in textile.
A Strategic Approach: GenAI in EducationPeter Windle
Artificial Intelligence (AI) technologies such as Generative AI, Image Generators and Large Language Models have had a dramatic impact on teaching, learning and assessment over the past 18 months. The most immediate threat AI posed was to Academic Integrity with Higher Education Institutes (HEIs) focusing their efforts on combating the use of GenAI in assessment. Guidelines were developed for staff and students, policies put in place too. Innovative educators have forged paths in the use of Generative AI for teaching, learning and assessments leading to pockets of transformation springing up across HEIs, often with little or no top-down guidance, support or direction.
This Gasta posits a strategic approach to integrating AI into HEIs to prepare staff, students and the curriculum for an evolving world and workplace. We will highlight the advantages of working with these technologies beyond the realm of teaching, learning and assessment by considering prompt engineering skills, industry impact, curriculum changes, and the need for staff upskilling. In contrast, not engaging strategically with Generative AI poses risks, including falling behind peers, missed opportunities and failing to ensure our graduates remain employable. The rapid evolution of AI technologies necessitates a proactive and strategic approach if we are to remain relevant.
How to Make a Field invisible in Odoo 17Celine George
It is possible to hide or invisible some fields in odoo. Commonly using “invisible” attribute in the field definition to invisible the fields. This slide will show how to make a field invisible in odoo 17.
Macroeconomics- Movie Location
This will be used as part of your Personal Professional Portfolio once graded.
Objective:
Prepare a presentation or a paper using research, basic comparative analysis, data organization and application of economic information. You will make an informed assessment of an economic climate outside of the United States to accomplish an entertainment industry objective.
June 3, 2024 Anti-Semitism Letter Sent to MIT President Kornbluth and MIT Cor...Levi Shapiro
Letter from the Congress of the United States regarding Anti-Semitism sent June 3rd to MIT President Sally Kornbluth, MIT Corp Chair, Mark Gorenberg
Dear Dr. Kornbluth and Mr. Gorenberg,
The US House of Representatives is deeply concerned by ongoing and pervasive acts of antisemitic
harassment and intimidation at the Massachusetts Institute of Technology (MIT). Failing to act decisively to ensure a safe learning environment for all students would be a grave dereliction of your responsibilities as President of MIT and Chair of the MIT Corporation.
This Congress will not stand idly by and allow an environment hostile to Jewish students to persist. The House believes that your institution is in violation of Title VI of the Civil Rights Act, and the inability or
unwillingness to rectify this violation through action requires accountability.
Postsecondary education is a unique opportunity for students to learn and have their ideas and beliefs challenged. However, universities receiving hundreds of millions of federal funds annually have denied
students that opportunity and have been hijacked to become venues for the promotion of terrorism, antisemitic harassment and intimidation, unlawful encampments, and in some cases, assaults and riots.
The House of Representatives will not countenance the use of federal funds to indoctrinate students into hateful, antisemitic, anti-American supporters of terrorism. Investigations into campus antisemitism by the Committee on Education and the Workforce and the Committee on Ways and Means have been expanded into a Congress-wide probe across all relevant jurisdictions to address this national crisis. The undersigned Committees will conduct oversight into the use of federal funds at MIT and its learning environment under authorities granted to each Committee.
• The Committee on Education and the Workforce has been investigating your institution since December 7, 2023. The Committee has broad jurisdiction over postsecondary education, including its compliance with Title VI of the Civil Rights Act, campus safety concerns over disruptions to the learning environment, and the awarding of federal student aid under the Higher Education Act.
• The Committee on Oversight and Accountability is investigating the sources of funding and other support flowing to groups espousing pro-Hamas propaganda and engaged in antisemitic harassment and intimidation of students. The Committee on Oversight and Accountability is the principal oversight committee of the US House of Representatives and has broad authority to investigate “any matter” at “any time” under House Rule X.
• The Committee on Ways and Means has been investigating several universities since November 15, 2023, when the Committee held a hearing entitled From Ivory Towers to Dark Corners: Investigating the Nexus Between Antisemitism, Tax-Exempt Universities, and Terror Financing. The Committee followed the hearing with letters to those institutions on January 10, 202
Honest Reviews of Tim Han LMA Course Program.pptxtimhan337
Personal development courses are widely available today, with each one promising life-changing outcomes. Tim Han’s Life Mastery Achievers (LMA) Course has drawn a lot of interest. In addition to offering my frank assessment of Success Insider’s LMA Course, this piece examines the course’s effects via a variety of Tim Han LMA course reviews and Success Insider comments.
Unit 8 - Information and Communication Technology (Paper I).pdfThiyagu K
This slides describes the basic concepts of ICT, basics of Email, Emerging Technology and Digital Initiatives in Education. This presentations aligns with the UGC Paper I syllabus.
Introduction to AI for Nonprofits with Tapp NetworkTechSoup
Dive into the world of AI! Experts Jon Hill and Tareq Monaur will guide you through AI's role in enhancing nonprofit websites and basic marketing strategies, making it easy to understand and apply.
The French Revolution, which began in 1789, was a period of radical social and political upheaval in France. It marked the decline of absolute monarchies, the rise of secular and democratic republics, and the eventual rise of Napoleon Bonaparte. This revolutionary period is crucial in understanding the transition from feudalism to modernity in Europe.
For more information, visit-www.vavaclasses.com
Francesca Gottschalk - How can education support child empowerment.pptxEduSkills OECD
Francesca Gottschalk from the OECD’s Centre for Educational Research and Innovation presents at the Ask an Expert Webinar: How can education support child empowerment?
Palestine last event orientationfvgnh .pptxRaedMohamed3
An EFL lesson about the current events in Palestine. It is intended to be for intermediate students who wish to increase their listening skills through a short lesson in power point.
3. Finishing is a general term which usually refers to treatment on textile fabrics
after dyeing or printing.
It increase life and durability of the fabric.
By finishing we can maintain fabric shape and size.
Finishing accentuate or inhibiti some characteristic of fabric.
Impart new characteristic or properties.
Finishes may be done by chemically or mechanically.
To get good finished quality we should maintain machine parameter or proper
chemical recipe.
We can improve finished product quality by developing machine parameter or
create new and appropriate chemical recipe.
4. •To improve the appearance of the fabric.
•To improve the feel of the fabric by softening, stiffening, etc.
•To cover faults in the original fabric.
•To increase weight of the cloth.
•Special properties required for particular uses .
5. Types of finishing
The most common classifications:
Aesthetic finishes
Functional finishes
Finishes also classifies:
8. After dyeing process from the dyeing machine then the fabrics are ready for de-watering. This is the
process to remove the water from the fabrics partially by squeezing.
Process flow chart:
Fig: Crossectional view of Bianco Tube Squeezer.
Basic function of the squeezing m/c:
To remove the water from the fabric.
To control the width of the fabric.
To control the length of the fabric.
To control the spirality of the fabric.
To control the over feeding system.
To increase the softness of the fabric.
To remove the crease mark of the fabric.
9. • The slitting machine is used in processing fabrics in the open line in the finishing section.
Main Parts:
*Turn table; *Beater; *Rope; *De- twister; *Centering unit; *Slitting unit
*Pulley drive *Squeezing
Process flow chart:
Figure: Passage Diagram of Slitting Machine of Brueckner
Machine Functions:
•To slit the tube fabric by the knife for opening of the fabric and ready for stentering.
•Delivered fabric is crease free state.
•Before squeezing balloon is formed with the help of compressed air passing by a nozzle or air
sprayer.
•It can control the diameter of fabric and GSM and shrinkage by over feeding mechanism.
•Soften the fabric by applying the softeners.
10. •The machine is used for removing the residual water contained in the fabric after squeezing by applying
heat on the fabric in the machine.
•the fabric is feed on the drying net at low over feed speed and the humidity is continuously measured.
•Drying is done by applying heat through burner nozzles.
Main parts:
•Heating chamber
•Blower
•Synthetic blanket as a conveyor
•Folder
•Exhaust fan
•Steam valve
•Conveyer roller
•Tension roller
Machine Functions:
•To dry the fabric with help of steam
•To control the shrinkage
•To prepare for next subsequent process
•To dry tubular and open width fabric without tension.
•To remove residual water containing in the fabric.
11. Stenter
Machine:•Stenter is used for open form fabric. It is the heart of open knit finishing sector.
Main Parts & Zones:
Back Zone:
#Guider ; #Two Baths & Padder or Squeezer; #Auto centering
Middle Zone:
#Over feed regions; #Bianco or Mahlo arrangement; #Chain & clip system;
#Chambers (Contains blower, heater, recovery)
Front Zone:
#Over feed zone ; #Plaiting; #Static electricity remover
Figure : Passage Diagram of Stenter
Machine Functions:
•To control the shrinkage
•To control the required GSM by overfeed
•To control the required dia.
•Heat setting
•For straighten the fabric
•To control bowing & bias (spirality)
•For uniform moisture content
•Finishing chemical application
•Selvedge gumming & cutting
12. •The treatment of knit fabrics in tubular form on the TUBULAR COMPACTOR meets the exacting
standards set by customers
Main Machine Parts:
•Feed section: Tension control & Metal detector.
•Shape: Set according to the dia. of fabric
•Steam zone
•Take out & Plaiter zone
•Compacting Zone: It’s a roller & shoe arrangement & the most important zone which consists of two
rollers, the Feed roller (Recarter roller) & the Retard roller. They are heated by Shoe, into which hot
thermo-oil runs through.
Fig: Cross sectional View of Tube Compactor Machine
Basic functions of the Tube compactor machine:
•To control the GSM. (Increase & decrease).
•To control the dia.
•To control the shrinkage. (Increase & decrease).
•Width control through a stepless adjustable special tubular fabric spreader driven by variable speed
motor for distortion-free fabric guidance.
•Steamping with a condensate-free steam box which is easily operated and completely made from
stainless stell.
•Compacting through two Nomex felt belts.
•Calendaring while passing between the felt belt and the heated shrinking rollers.
13. •Open Width Compactor is suitable for open width knit fabrics to achieve exact dimensional stability and a
soft feel.
Main Parts of the Machine:
•Heating chamber
•Blower (2, one at the entry chain zone for uncurling and another at the entry of compacting zone)
•ynthetic blanket as a conveyor,
•Folder
•Exhaust fan
•Unpinning cylinder (-40% (+-)40%)
•Belt cylinder (-40% ( +-)40%)
•Uncurling device at entry of compacting zone.
•Sensor
•Brush roller
Figure: Passage diagram of Corino Open Compactor
Machine Function:
•To compact the fabric
•To control the shrinkage
•To maintain proper width and G.S.M
•To make the fabric surface smooth
14. •During raising, the fabric surface is treated with sharp teeth to lift the surface fibres, thereby imparting
hairiness, softness and warmth, as in flannelette.
Main parts:
•Return drag roller
•Pile
•Counter pile
•Front drag roller
•Suction pump
•Drum
•Plaiter roller
Feed
Delivery
Pile
Counter
pile
Front drag
Roller
Rear drag
Roller
Return drag
roller
Plaiter
roller
Figure : Cross-sectional view of Raising Brush machine
Machine Functions:
•To obtain a lofty handle effect on fabric.
•To obtain fleece appearance.
•To create pile on fabric surface.
•To produce a heavier surface made of fibers.
15.
16. •Softening treatment is one of the most important chemical after treatments in the textile industry.
•By softening treatment textile can achieve not only soft handle but also:
Some smoothness.
More flexibility.
Drape and Pliability.
Antistatic properties.
Luster.
Soft handle.
Types of
softeners:
17. Advantages:
•Resins have a profound effect on and cause changes in the hand (feel), drapability and physical
characteristics of textiles.
•They add stiffness to fabrics and are thus used as stiffening agents or to create a firm hand.
•Yarns in fabric will be stabilized and will resist shrinkage in laundering.
•This finish imparts luster to the cotton.
•Increases cotton strength by nearly 25% and improves dye affinity.
•It is a method of thickening woollen material to make it more water-resistant
18.
19. •Nanotechnology is an umbrella term covering a wide range of technologies concerned with
structures and processes on the nanometric scale.
•. Nanotechnology deals with the science and technology at dimensions of roughly 1 to 100
nanometers (1 Billion Nanotechnology = 1metre), although 100 nanometers presently is the
practically attainable dimension for textile products and applications.
•The Nanotechnology can be used in engineering desired textiles attributes, such as fabric
softness, namely, water repellency, fire retardancy, antimicrobial resistance etc in fibers,
yarns and fabrics.
•Enhancement of textile materials by nanotechnology is expected to become a trillion dollar
industry in the next decade, with tremendous economic and ecology benefits.
•With the advent of nanotechnology, a new area has developed in the realm of textile
finishing.
20. Antimicrobial Finish:
• It is a well-known fact that the growth of bacteria and microorganisms in food or water is
prevented hen stored in silver vessels due to its antibacterial properties.
• The antibacterial properties of silver are now scientifically recognized.
• Silver ions have been spectrum of antimicrobial activities.
• The method of producing durable silver containing antimicrobial finish is to encapsulate silver
compound or nano particle with a fiber reactive polymer like poly (styrene-maleric anhydride).
• Products which are commonly applied are brominated phenols, quaternary ammonium
compounds, organo-silver and tin compounds, which can be applied as solutions or
dispersions.
• They can also be incorporated in a polymeric film deposited on the surface to achieve
controlled release.
• The rays in the wavelength region of 150 to 400nm are known as ultraviolet radiations.
•ultraviolet absorber finish of a fabric is present that absorbs ultraviolet radiation and blocks
its transmission through a fabric to the skin.
•Metal oxides like ZnO as UV-blocker are more stable when compared to organic UV-
blocking agents.
•Hence, nano ZnO will really enhance the UV-blocking property due to their increase
surface area and intense absorption in the UV region.
22. • Nano-processed garments have protective coating, which is water and
beverage repellent.
• Their protective layer is difficult to detect with the naked eye.
• Saving time and laundering cost.
• This technology embraces environment friendly properties.
• The crease resistant feature keeps clothing neat.
• Nano- processed products are toxic free.
• Garments stay bright, fresh looking and are more durable than ordinary
materials.
• Manufacturing cost is low, adding value to the products.
23.
24. •Parameter:
•Padder (1): 4-5 bar ; Padder (2): 3.5- 4 bar
Fabric type Fabric speed (m/min) Over feed %
Single jersey (Viscose) 50-70 30
Single jersey(Cotton/Lycra) 60-80 22
Single jersey(Cotton) 60-80 10-11
1x1 Rib 20-30 11
Interlock 20-30 14-15
terry 40-50 5-9
Single jersey- 180GSM (exp.) 70 25%
Checking point:
Diameter; Fabric speed; Overfeeds; Padder pressure
Development:
Wet Squeezer Marks
Softener Mark
25. Parameter:
Fabric type Speed
m/min
Over feed
%
Padder
Pressure 1
Padder pressure2
Single jersey 60-80 2.5-3 1.5 bar (chemical)- 2bar
(normal)
3 bar (chemical)- 4bar
(normal)
1×1 rib 30-40 2.5-3 1.25 bar (chemical) -3bar
(normal)
2.5 bar (chemical)-
3 bar (normal)
2×2 rib 20-30 2.5-3 1.25 bar (chemical) -3bar
(normal)
2.5bar (chemical)-
3 bar (normal)
Loop back 20-30 2.5-3 1.5 bar (chemical)- 2bar
(normal)
3 bar (chemical)- 4bar
(normal)
Single jersey
(160GSM) EXP
75 2.8 1.5 bar 3 bar
Checking point:
Needle line; machine speed.
Development:
Softener spot
Improper slitting
26. Fabric
type
Color Speed Over feed Temperature
(°C)
Stretch
(%)
s/j White 10 15-20 120 35
Dyed 8-10 15-20 120-130 35
PK White 12-15 30 120 50
Dyed 15 30 120-140 50
1×1 rib White 7-8 10 120-140 20
Dyed 7-8 10 130-140 20
2×2 rib White 7-8 20 120 25
Dyed 7-8 20 120-130 25
s/j (160 GSM) EXP. White 10 20 130 35
Parameter:
Checking point:
Speed; Temperature.
Development:
Overheating and Shade Variation.
27. Parameter:
Fabric
Parameter
Single jersey l-Rib PK Fleece/ terry Single jersey
EXP.
Required Dia (cm) 88 80 54 80 190
Actual Dia (cm) 90.5 88 67 84 208
Required GSM 160 240 210 240 260
Actual GSM 148 218 185 232 240
Temperature (°C) 170 170 170 170 160
Overfeed 60 45 60 40 40
Machine Speed 20 18 18 16 20
Controlling point:
Temperature ; Width setting; Overfeed; Speed.
Development:
Spirality problem
GSM variation & width variation for lycra fabric.
Wrong and narrow width
Startch stains and white lines on finished cloth
28. Parameter:
Over-feed ratio: Edge drive zone – 1.0-1.5
Retard roller – 0.80-0.85
Take-out zone – 0.85-0.90
Conveyor belt – 1.0-1.05
Plaiter – 0.80-0.85
Shoe pressure: S/J – large dia. – avg. 30 psi
S/J – smaller dia. – 10-15 psi
Rib – 10-20 psi
Lycra - <10 psi
Types of
fabric
Buyer Color Over
feed
Reqd.
GSM
Finished
GSM
M/C
dia.
(cm)
Reqd.
Dia.
Finished
dia.
Temp
0
C
RP
M
Single jersey Name IT Black 60% 180 178 115 100 98 1100
C 15
J &J Navy 60% 190 207 195 64″ 71″ 1100
C 18
1×1 Rib Pimkie 0350 60% 210 205 210 74″ 75″ 1000
C 18
2×2 Rib
(lycra)
Russel Black 60% 180 180 180 64″ 68″ 1100
C 18
Interlock Kappa Khaki 60% 260 300 200 75″ 72″ 1100
C 18
Polyester
fabric
Rex &
Holm
Khaki 60% 190 185 190 64″ 67″ 1100
C 20
Fleece Kappa Blue 60% 260 228 210 74″ 77.5″ 1100
C 18
Interlock EXP. Blue 60% 330 288 224 222 1150
C 20
Development:
Folding Marks
GSM Variation
29. Conclusion
•We all have tried our level best in accomplishing the project.
•Lack of presentation time we skip some topic which we include ours
presentation book.
•We are greatly thankful to the management and staffs of the companies namely
“GMS Composite Knitting IND. Ltd.”, “ Raiyan Knit Composite Ltd ” .Without
their constant support it could not have been possible
•. In our project we came up mainly with different kinds of knit finishing parameter
& development in different machines.
•In the project of us we included the each machines in the finishing lines, their
working mechanism, their technical data, machine specification, ways of
controlling different important parameters, faults and remedies.
•We express our heartiest thanks to our project supervisor and honorable
teacher, Najmul Ehsan, Lecturer of the Department of Textile Engineering for his
logical guidelines, constant inspirations, necessary instructions and proper
supervision
31. Abstract:
We have tried to present all types of finishing processes. Most of the finishing
processes are not conduct in Bangladesh. In our country function finishing
process is done mostly. Aesthetic finishing are more expensive than functional.
We tried hard to give accurate parameter and solve the fault of finishing
process. That’s how we can develop finishing process and give more
production. Due to limitation our knowledge we did not all finishing processes.
We think that our internship and project paper based on finishing will increase
our knowledge in many sides.