The document provides information on NORDEL EPDM products from Dow, which are ethylene propylene diene monomer polymers available with a wide range of ethylene contents. The polymers offer improved performance characteristics such as yield, reduced scrap, and cleanliness. NORDEL EPDM polymers are sold in bale and pellet forms. Tables and figures provide details on properties and applications of various grades of NORDEL EPDM and how they compare in testing. The document also summarizes FDA compliance of grades.
location and identification for defect, grinding then welding build up according to repair procedure ,then flushing .
*step by step fabrication and NDE activities.
1. OBJECT
The hardness test is a mechanical test for material properties which are used in engineering
design, analysis of structures, and materials development. The principal purpose of the
hardness test is to determine the suitability of a material for a given application, or the
particular treatment to which the material has been subjected. The ease with which the
hardness test can be made has made it the most common method of inspection for metals and
alloys.
This manual covers the basic guidelines and minimum requirements for
periodic inspection of heat exchangers used in petroleum refinery.
Locations to be inspected, inspection tools, frequency of inspection &
testing, locations prone to deterioration and causes, corrosion
mitigation, inspection and testing procedures have been specified in
the manual.
Documentation of observations & history of heat exchangers,
inspection checklist and recommended practices have also been
included.
Heat exchanging equipment is used for heating or cooling a fluid.
Individual heat transfer equipment is named as per its function.
Cooler
A cooler cools the process fluid, using water or air, with no change of
phase.
Chiller
A chiller uses a refrigerant to cool process fluid to a temperature below
that obtainable with water.
Condenser
A condenser condenses a vapour or mixture of vapours using water or
air.
Exchanger
An exchanger performs two functions in that it heats a cold process
fluid by recovering heat from a hot fluid, which it cools. None of the
transferred heat is lost.
Piping components, materials, codes and standards part 1- pipeAlireza Niakani
The course is focused on four areas: piping components, pipe materials and manufacture, sizes, codes and standards. Applicable piping codes for oil and gas facilities (ISO, B31.3, B31.4, B31.8, etc.), pipe sizing calculations, pipe installation, and materials selection are an integral part of the course. The emphasis is on proper material selection and specification of piping systems.
location and identification for defect, grinding then welding build up according to repair procedure ,then flushing .
*step by step fabrication and NDE activities.
1. OBJECT
The hardness test is a mechanical test for material properties which are used in engineering
design, analysis of structures, and materials development. The principal purpose of the
hardness test is to determine the suitability of a material for a given application, or the
particular treatment to which the material has been subjected. The ease with which the
hardness test can be made has made it the most common method of inspection for metals and
alloys.
This manual covers the basic guidelines and minimum requirements for
periodic inspection of heat exchangers used in petroleum refinery.
Locations to be inspected, inspection tools, frequency of inspection &
testing, locations prone to deterioration and causes, corrosion
mitigation, inspection and testing procedures have been specified in
the manual.
Documentation of observations & history of heat exchangers,
inspection checklist and recommended practices have also been
included.
Heat exchanging equipment is used for heating or cooling a fluid.
Individual heat transfer equipment is named as per its function.
Cooler
A cooler cools the process fluid, using water or air, with no change of
phase.
Chiller
A chiller uses a refrigerant to cool process fluid to a temperature below
that obtainable with water.
Condenser
A condenser condenses a vapour or mixture of vapours using water or
air.
Exchanger
An exchanger performs two functions in that it heats a cold process
fluid by recovering heat from a hot fluid, which it cools. None of the
transferred heat is lost.
Piping components, materials, codes and standards part 1- pipeAlireza Niakani
The course is focused on four areas: piping components, pipe materials and manufacture, sizes, codes and standards. Applicable piping codes for oil and gas facilities (ISO, B31.3, B31.4, B31.8, etc.), pipe sizing calculations, pipe installation, and materials selection are an integral part of the course. The emphasis is on proper material selection and specification of piping systems.
This data sheet and properties information has been uploaded and shared by Emco Industrial Plastics. This plastics distributor, manufacturer and fabrication company has everything that you need for your engineering and tooling needs.
To purchase Delrin AF visit http://www.emcoplastics.com/materials/delrin/delrin-af-100/
Shown for the first time at the VII Moscow International Lubricant Week, Molykote® experts present a new range of lubricants developed through the use of unique patented technology.
New silicone copolymer lubricants combine the thermal stability of phenyl siloxanes with the wear resistance of fluoro siloxanes to deliver increased wear resistance even at high temperatures. The balance of phenyl and fluoro groups can be adjusted to produce the ideal solution for each tribological challenge.
With high-temperature lubricity achieved, without sacrificing low-temperature operation, these new oils and greases function effectively in a wide range of temperatures (-35°C to 220°C) – delivering superior performance against ester based lubricants. With a lower density than PFPE lubricants, they offer lower cost-per-use and their wide additive acceptance delivers additional properties such as corrosion and oxidation resistance.
See the results of the research and development along with a direct comparison against a range of silicone, PFPE and ester based lubricants.
A wide range of applications are emerging as we work with industry to launch further ranges within this group. Contact your Molykote representative now to request a development sample.
La energía eólica es la fuente de energía de mayor crecimiento en el mundo, este tipo de energía aporta a la industria y las empresas electricidad limpia y renovable.
Hoy en día, el diseño de los aerogeneradores y las turbinas de los molinos se está volviendo cada vez más complejo y sofisticado, para poder construir parques eólicos que puedan operar en condiciones altamente exigentes en lugares en alta mar y en climas fríos y / o cálidos.
Huntsman Advanced Materials es un apasionado de mejorar la calidad de vida de las personas en todo el mundo. Desde hace más de una década, la compañía se centró en apoyar la cadena de valor de la energía eólica. Los equipos de Investigación y Desarrollo, así como el equipo de asistencia técnica, han trabajado estrechamente con la industria y con todos los principales fabricantes de equipos de energía eólica para desarrollar la tecnología más avanzada que mejora los índices de resistencia / peso y los requisitos de fatiga.
What Does the Active Steering Malfunction Warning Mean for Your BMWTanner Motors
Discover the reasons why your BMW’s Active Steering malfunction warning might come on. From electrical glitches to mechanical failures and software anomalies, addressing these promptly with professional inspection and maintenance ensures continued safety and performance on the road, maintaining the integrity of your driving experience.
What Exactly Is The Common Rail Direct Injection System & How Does It WorkMotor Cars International
Learn about Common Rail Direct Injection (CRDi) - the revolutionary technology that has made diesel engines more efficient. Explore its workings, advantages like enhanced fuel efficiency and increased power output, along with drawbacks such as complexity and higher initial cost. Compare CRDi with traditional diesel engines and discover why it's the preferred choice for modern engines.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
Core technology of Hyundai Motor Group's EV platform 'E-GMP'Hyundai Motor Group
What’s the force behind Hyundai Motor Group's EV performance and quality?
Maximized driving performance and quick charging time through high-density battery pack and fast charging technology and applicable to various vehicle types!
Discover more about Hyundai Motor Group’s EV platform ‘E-GMP’!
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
Why Isn't Your BMW X5's Comfort Access Functioning Properly Find Out Here
Nordel selection guide
1. NORDEL™
EPDM
Product Selection Guide
NORDEL™ EPDM products are members of
Dow’s family of ethylene propylene diene
monomer polymers and feature the widest
range of ethylene content available in the
industry. These high-quality, ultra-low gel
polymers provide improved yield, scrap
reductions, and unparalleled polymer
cleanliness. NORDEL™ EPDM polymers
are sold in bale form, as well as free-
flowing pellets.
®
™Trademark of The Dow Chemical Company (“Dow”) or an affiliated company of Dow Dow Elastomers
40 50 60 70 80 90
MooneyViscosity,ML1+4at125°C
Ethylene Content, wt.%
NORDEL IP 3640
NORDEL IP 4760P
NORDEL IP 4640
NORDEL IP 5565
NORDEL IP 4570
NORDEL IP 4520
90
70
50
30
10
NORDEL IP 4770P
NORDEL IP 4820P
NORDEL IP 4725P
NORDEL IP 3760P
NORDEL IP 3722PNORDEL IP 3720P
NORDEL IP 3745P
Diene Level
Very Low, <1%
Medium, 1-3%
High, 3-6%
Very High, >6%
Suffix designation: P or HM = sold only as pellets; No suffix = bale form
NORDEL IP 4785HM
NORDEL™
EPDM RESINS OFFER EXCEPTIONAL POLYMER CLEANLINESS
Figure 1: Property Ranges of NORDEL™
EPDM Products
2. Table 1: Typical Properties and Applications of NORDEL™
EPDM(1)
Product Grade
Mooney Viscosity, ML 1+4
at 125°C (ASTM D1646)
Ethylene, Mass %
(ASTM D3900)
ENB, Mass %
(ASTM D6047)
MWD Characteristics
(Dow Test Method)
NORDEL™
IP 3640 40 55 1.8 Medium
NORDEL™
IP 3720P 20 70 0.6 Broad
NORDEL™
IP 3722P 18 71 0.5 Medium
NORDEL™
IP 3745P 45 70 0.5 Narrow
NORDEL™
IP 3760P 63 67 2.2 Medium
NORDEL™
IP 4520 20 50 4.9 Medium
NORDEL™
IP 4570 70 50 4.9 Medium
NORDEL™
IP 4640 40 55 4.9 Medium
NORDEL™
IP 4725P 25 70 4.9 Broad
NORDEL™
IP 4760P 60 67 4.9 Medium
NORDEL™
IP 4770P 70 70 4.9 Medium
NORDEL™
IP 4785HM 85 68 4.9 Medium
NORDEL™
IP 4820P 20 85 4.9 Narrow
NORDEL™
IP 5565 65 50 7.5 Medium
(1)
Data per tests conducted by Dow. Test protocols and additional information available upon request. Properties shown are typical, not to be construed as specifications. (continued)
DURABLE PRODUCTS FOR WEATHERSTRIPPING, SEALS, AND GASKETS PLIABLE AND WEATHER-RESISTANT FORMULATIONS FOR RESIDENTIAL AND INDUSTRIAL HOSES
2
™Trademark of The Dow Chemical Company (“Dow”) or an affiliated company of Dow
3. Table 1: Typical Properties and Applications of NORDEL™
EPDM, continued(1)
Product Grade
Density, g/cm3
(ASTM D297)
Crystallinity,
Mass%, DSC,
10°C/min (Dow
Test Method)
Tc, °C
PQ-E-005
(Dow Test
Method)
Form Applications
NORDEL™
IP 3640 0.86 4 -10 Bales Blends with butyl rubber in inner tubes, peroxide-cured belts
NORDEL™
IP 3720P 0.88 14 43 Pellets
Thermoplastic modification, electrical insulation, molded
connectors, belts, rolls (peroxide-cured)
NORDEL™
IP 3722P 0.88 15 46 Pellets
Thermoplastic modification, electrical insulation, molded
connectors (peroxide-cured)
NORDEL™
IP 3745P 0.88 12 34 Pellets Thermoplastic modification, cable bedding, sound insulation
NORDEL™
IP 3760P 0.88 12 18 Pellets Roofing, belts
NORDEL™
IP 4520 0.86 1 – Bales
Molded seals, brake diaphragms, gaskets, sealants,
weatherstrip corner molding
NORDEL™
IP 4570 0.86 1 – Bales
Extrusions, automotive and general purpose hose, profile
gaskets, weatherstripping
NORDEL™
IP 4640 0.86 4 -10 Bales
Molded automotive and industrial parts, hose and tubing,
weatherstrip, belts
NORDEL™
IP 4725P 0.88 12 36 Pellets Rolls, high hardness compounds, gaskets, extruded profiles
NORDEL™
IP 4760P 0.88 10 35 Pellets
Extrusions, automotive and general purpose hose, profile
gaskets, weatherstripping
NORDEL™
IP 4770P 0.88 13 34 Pellets
Automotive and general purpose hose, extruded profiles,
glass run channel, low voltage wire and cable
NORDEL™
IP 4785HM 0.88 8 29 Pellets Weatherstripping, extrusions, profiles
NORDEL™
IP 4820P 0.91 28 79 Pellets
Property modification of thermoplastic polyolefin
and thermoset rubber formulations – high hardness,
weatherstrip, molded goods
NORDEL™
IP 5565 0.86 1 – Bales Weatherstripping, cellular profiles
(1)
Data per tests conducted by Dow. Test protocols and additional information available upon request. Properties shown are typical, not to be construed as specifications.
3
™Trademark of The Dow Chemical Company (“Dow”) or an affiliated company of Dow
4. Table 2: Comparison of NORDEL™
EPDM Grades in Peroxide-cure Test Recipe(1, 2, 3)
Property
NORDEL™
EPDM Grades
IP 3640 IP 3720P IP 3722P IP 3745P IP 4520 IP 4570 IP 4640
Mooney Viscosity, ML 1 + 4, 100°C 50 25 27 59 32 72 50
Mooney Scorch at 125°C, Minutes to 5 pt. rise 30 30 30 30 30 13 20
MDR at 175°C, 0.5° Arc, 30 min cht
ML, dN.m 1.4 0.8 0.8 1.5 1.0 1.9 1.3
MH, dN.m 8.5 7.5 8.1 11.3 10.4 17.9 15.4
ts1, min 0.6 0.6 0.58 0.51 0.82 0.38 0.41
tc90, min 6.0 7.0 7.5 5.8 7.6 6.8 7.2
Vulcanizate Properties, Physical Properties at R.T. Press-cured: tc95+3 min at 175°C
Tensile Strength, MPa 8.1 8.0 8.1 12.2 8.5 12.5 11.1
Elongation, % 300 324 275 307 253 245 230
Modulus at 100% Elongation, MPa 1.9 3.0 3.3 3.4 2.7 3.0 3.4
Modulus at 200% Elongation, MPa 5.1 5.6 6.3 8.7 6.6 9.1 8.9
Hardness, Shore A 53 72 71 67 58 57 61
Compression Set, Method B Pellets Cured
MDR tc95+15 min
22 hr at -10°C 66 91 93 98 40 28 42
22 hr at 70°C 17 30 29 21 9 8 8
22 hr at 100°C 12 20 20 19 9 7 8
70 hr at 150°C 21 30 29 27 18 16 17
Temperature Retraction,°C
TR-10 -39 -14 -13 -18 -43 -45 -30
TR-20 -31 -1 1 -6 -36 -38 -20
TR-50 -17 14 15 9 -24 -29 23
Change in Properties Aged in Air 70 Hours at 150°C
Tensile Strength, MPa 7.9 7.7 8.1 11.4 8.3 11.0 11.9
Elongation, % 292 314 301 341 250 237 244
Elongation Change, % 2.9 -2.9 9.3 11.3 -1.3 -3.2 6.3
Modulus at 100% Elongation, MPa 2.2 3.3 3.4 3.4 2.6 3.4 3.3
Modulus Change, % 16.1 10.1 4.9 1.5 -0.8 11.7 -1.5
Hardness, Shore A 59 75 75 70 60 64 64
Hardness Change, pts 6 3 4 3 2 7 3
(1)
Data per tests conducted by Dow. Test protocols and additional information available upon request. Properties shown are typical, not to be construed as specifications. (continued)
(2)
Test Recipe: Polymer – 100 phr, N-650 Black – 115 phr, Paraffinic Oil – 70 phr, DCP-40% – 8 phr, TMQ – 1 phr, HVA #2 – 1 phr.
(3)
All components tested per standard ASTM Method.
4
™Trademark of The Dow Chemical Company (“Dow”) or an affiliated company of Dow
5. Table 2: Comparison of NORDEL™
EPDM Grades in Peroxide-cure Test Recipe(1, 2, 3)
, continued
Property
NORDEL™
EPDM Grades
IP 4725P IP 4760P IP 4770P IP 4785HM IP 4820P IP 5565
Mooney Viscosity, ML 1 + 4, 100°C 31 65 72 84 22 67
Mooney Scorch at 125°C, Minutes to 5 pt. rise 26 14 11 12 29 10
MDR at 175°C, 0.5° Arc, 30 min cht
ML, dN.m 0.9 1.6 2.2 2.0 0.3 2.0
MH, dN.m 12.8 18.2 19.6 16.0 18.9 16.4
ts1, min 0.48 0.38 0.36 0.4 0.39 0.4
tc90, min 8.2 6.7 6.6 2.6 9.0 7.1
Vulcanizate Properties, Physical Properties at R.T. Press-cured: tc95+3 min at 175°C
Tensile Strength, MPa 12.7 15.0 16.6 13.8 17.1 13.3
Elongation, % 247 254 238 296 184 214
Modulus at 100% Elongation, MPa 4.1 4.2 5.2 4.4 9.3 4.2
Modulus at 200% Elongation, MPa 9.6 11.0 13.8 9.7 – 12.7
Hardness, Shore A 72 67 71 73 90 59
Compression Set, Method B Pellets Cured
MDR tc95+15 min
22 hr at -10°C 99 80 83 – 99 21
22 hr at 70°C 15 9 8 9 77 6
22 hr at 100°C 11 8 6 9 8 5
70 hr at 150°C 21 16 15 21 16 15
Temperature Retraction,°C
TR-10 -20 -12 -4 – – -42
TR-20 -7 2 9 – – -38
TR-50 10 23 23 – – -28
Change in Properties Aged in Air 70 Hours at 150°C
Tensile Strength, MPa 12.3 15.5 16.6 12.7 16.5 12.9
Elongation, % 247 254 235 260 181 211
Elongation Change, % 0.0 -0.1 -1.3 -12.37 -1.4 -1.3
Modulus at 100% Elongation, MPa 4.5 4.3 5.2 4.6 10.2 4.0
Modulus Change, % 8.7 2.6 1.2 4.9 9.9 -4.5
Hardness, Shore A 74 69 72 77 93 62
Hardness Change, pts 2 2 1 3 3 3
(1)
Data per tests conducted by Dow. Test protocols and additional information available upon request. Properties shown are typical, not to be construed as specifications.
(2)
Test Recipe: Polymer – 100 phr, N-650 Black – 115 phr, Paraffinic Oil – 70 phr, DCP-40% – 8 phr, TMQ – 1 phr, HVA #2 – 1 phr.
(3)
All components tested per standard ASTM Method.
5
™Trademark of The Dow Chemical Company (“Dow”) or an affiliated company of Dow
6. Table 3: Summary of FDA Compliance by NORDEL™
EPDM Grade(1)
Product Grade 21 CFR 177.2600 21 CFR 177.1520(2)
21 CFR 175.105(3)
21 CFR 177.1210
NORDEL™
IP 3640 Yes Yes Yes Yes
NORDEL™
IP 3720P Yes No Yes No
NORDEL™
IP 3722P Yes No Yes No
NORDEL™
IP 3745P Yes Yes Yes Yes
NORDEL™
IP 3760P – – – –
NORDEL™
IP 4520 Yes No Yes No
NORDEL™
IP 4570 Yes Yes Yes Yes
NORDEL™
IP 4640 Yes Yes Yes Yes
NORDEL™
IP 4725P Yes No Yes No
NORDEL™
IP 4760P Yes Yes Yes Yes
NORDEL™
IP 4770P Yes Yes Yes Yes
NORDEL™
IP 4785HM Yes Yes Yes Yes
NORDEL™
IP 4820P Yes Yes(4)
Yes No
NORDEL™
IP 5565 No No Yes No
(1)
Review current Code of Federal Regulations for specific details pertaining to food contact requirements.
(2)
Can be used in contact with all foods except water in oil emulsions, high or low fat, and low moisture fats and oil.
(3)
Adhesives only.
(4)
Compliant as a blend component in compliant polymers at levels up to 25% for conditions of use E through G.
HIGH-HEAT PRODUCTS FOR AUTOMOTIVE UNDERHOOD APPLICATIONS PROTECTIVE COMPOUNDS FOR ROOFING MEMBRANES
6
™Trademark of The Dow Chemical Company (“Dow”) or an affiliated company of Dow
7. Table 4: Package Types for NORDEL™
EPDM Product Grades
Product Grade
Inclusion Bag Box
Flexible Intermediate
Bulk Container
25 kg 385 kg 408 kg 800 kg
NORDEL™
IP 3640 X – – –
NORDEL™
IP 3720P X – X –
NORDEL™
IP 3722P X – X –
NORDEL™
IP 3745P X – X –
NORDEL™
IP 3760P X – – –
NORDEL™
IP 4520 X – – –
NORDEL™
IP 4570 X – – –
NORDEL™
IP 4640 X – – –
NORDEL™
IP 4725P X – – –
NORDEL™
IP 4760P X – – X
NORDEL™
IP 4770P X X – X
NORDEL™
IP 4785HM X – – X
NORDEL™
IP 4820P X X – –
NORDEL™
IP 5565 X – – X
Bag Melting Point, °C 87 – – –
Bag Material EVA/PE – – –
7
™Trademark of The Dow Chemical Company (“Dow”) or an affiliated company of Dow