This document discusses multiphase power converters. It begins by defining multiphase converters as those with more than three phases, which are an extension of three-phase converters with additional legs. Multiphase converters are used in applications involving AC to DC, DC to AC, AC to AC, and DC to DC conversion. They provide advantages like enhanced torque density, lower torque pulsation, higher frequency ripple, lower per-leg current rating, greater fault tolerance, and lower harmonic losses. The document goes on to describe types of multiphase converters and their applications in areas like adjustable speed drives, renewable energy systems, and electric vehicles.
IRJET- Variable Frequency Drive Used in TreadmillIRJET Journal
This document summarizes the use of variable frequency drives in treadmills. It discusses how most treadmills previously used DC brush motors but these had issues like high failure rates and maintenance costs. The document then explores how using an AC motor with a variable frequency drive can improve on the limitations of DC motors. It provides details on how variable frequency drives work, including discussing the rectifier, DC bus, inverter and control circuit components. It also explains techniques like pulse width modulation and flux vector control that are used to control the speed of AC motors. The objectives of using a variable frequency drive in a treadmill are listed as energy savings, increased life of components, reduced noise and vibration, lower thermal and mechanical stresses, and
Variable-frequency drives (VFDs) control AC motor speed and torque by varying motor input frequency and voltage. VFDs are used widely in industrial applications ranging from small appliances to large compressors and mills. They provide significant energy savings potential since around 25% of global electrical energy is used by electric motors. VFDs reduce costs and improve performance through advances in power electronics and control techniques. The main components of a VFD system are the AC motor, VFD controller, and operator interface. The controller converts AC power to variable frequency AC power to control the motor. Operators can start, stop and adjust motor speed using the interface. VFDs allow motors to operate across multiple speed and torque quadrants depending on
In the proposed approach,instead of a conventional 3- Phase inverter a component minimized single pha se inverter is utilized which reduces the cost of the inverter,th e switching losses,and the complexity of interface circuits to generate logic signals. A performance comparison of the prop osed inverter fed drive with a conventional 3Phase inverter fed drive is also mode in terms of speed response and t otal harmonic distortion (THD) of the stator curren t. The proposed inverter fed IM drive is found acceptable consideri ng its cost reduction and other advantageous featur es. A general pulse width modulation (PWM) method for c ontrol of 1-phase inverters is presented. The vecto r PWM offers a simple method to select three or four vectors tha t effectively synthesize the desired output voltage,even in presence of voltage oscillations across the two dc-link capacit ors. The influence of different switching patterns on output voltage symmetry,current waveform,switching frequency and common mode voltage can be examined. The paper als o discusses how the use of the wye and delta connecti ons of the motor windings affects the implementatio n of the pulse width modulator.
This document discusses different types of converters that can be used in switched reluctance motors (SRMs) to reduce torque ripple. It begins by outlining the requirements of SRM converters, including allowing phase overlap control and modulating phase voltage. It then describes six converter types - dump converters (R-dump and C-dump), asymmetric, bifilar, auxiliary, and high demagnetization converters. For each type, it provides a circuit diagram and overview of how it dissipates energy during phase commutation. It also models and simulates the performance of SRM drives using the different converter types in MATLAB. The document concludes that asymmetric converters are well-suited for high-speed SRM drives due to their fast current
Harmonic Analysis of Seven and Nine Level Cascade Multilevel Inverter using M...IAES-IJPEDS
The use of multilevel inverters has become popular in recent years for high- power applications. Multilevel Inverters are power converter systems composed by an array of power semiconductor sources that when properly connected and controlled can generate a multistep voltage waveform with variable and controllable frequency, phase and amplitude. This study deals with the comparison of a 7-level inverter with a 9-level inverter system; the voltage source inverters (VSI) are modelled and simulated using MATLAB Simulink and the results are presented. The test results verify the effectiveness of the proposed strategy in terms of computational efficiency as well as the capability of the inverter to produce very low distorted voltage with low-switching losses. This research aims to extend the knowledge about the performance of different clamped multilevel inverter through harmonic analysis. Simulations results validate up to the mark performance of the mentioned topologies.
Regeneration in Variable Frequency Drives and Energy Saving MethodsIRJET Journal
This document discusses methods for regenerating energy from variable frequency drives to save costs. When an induction motor decelerates, it generates electricity that is normally wasted as heat through braking resistors. Regenerative converters can return this energy to the grid instead. Three types are described: regenerative converters use PWM to feed energy back through the supply line; sinusoidal PWM converters regulate voltage while improving power quality; and matrix converters directly convert AC to AC with minimal components. Matrix converters integrate regeneration and driving but have limited voltage transfer. Regenerative converters provide significant utility cost savings, especially for applications with frequent braking like cranes or elevators.
A Modified C-Dump Converter for BLDC Machine Used in a Flywheel Energy Storag...IJERA Editor
This paper presents a modified C-dump converter for brushless DC (BLDC) machine used in the flywheel energy storage system. The converter can realize the energy bidirectional flowing and has the capability to recover the energy extracted from the turnoff phase of the BLDC machine. The principle of operation, modeling, and control strategy of the system has been investigated in the paper. Simulation and experimental results of the proposed system are also presented and discussed.
International Journal of Engineering Research and DevelopmentIJERD Editor
Electrical, Electronics and Computer Engineering,
Information Engineering and Technology,
Mechanical, Industrial and Manufacturing Engineering,
Automation and Mechatronics Engineering,
Material and Chemical Engineering,
Civil and Architecture Engineering,
Biotechnology and Bio Engineering,
Environmental Engineering,
Petroleum and Mining Engineering,
Marine and Agriculture engineering,
Aerospace Engineering.
IRJET- Variable Frequency Drive Used in TreadmillIRJET Journal
This document summarizes the use of variable frequency drives in treadmills. It discusses how most treadmills previously used DC brush motors but these had issues like high failure rates and maintenance costs. The document then explores how using an AC motor with a variable frequency drive can improve on the limitations of DC motors. It provides details on how variable frequency drives work, including discussing the rectifier, DC bus, inverter and control circuit components. It also explains techniques like pulse width modulation and flux vector control that are used to control the speed of AC motors. The objectives of using a variable frequency drive in a treadmill are listed as energy savings, increased life of components, reduced noise and vibration, lower thermal and mechanical stresses, and
Variable-frequency drives (VFDs) control AC motor speed and torque by varying motor input frequency and voltage. VFDs are used widely in industrial applications ranging from small appliances to large compressors and mills. They provide significant energy savings potential since around 25% of global electrical energy is used by electric motors. VFDs reduce costs and improve performance through advances in power electronics and control techniques. The main components of a VFD system are the AC motor, VFD controller, and operator interface. The controller converts AC power to variable frequency AC power to control the motor. Operators can start, stop and adjust motor speed using the interface. VFDs allow motors to operate across multiple speed and torque quadrants depending on
In the proposed approach,instead of a conventional 3- Phase inverter a component minimized single pha se inverter is utilized which reduces the cost of the inverter,th e switching losses,and the complexity of interface circuits to generate logic signals. A performance comparison of the prop osed inverter fed drive with a conventional 3Phase inverter fed drive is also mode in terms of speed response and t otal harmonic distortion (THD) of the stator curren t. The proposed inverter fed IM drive is found acceptable consideri ng its cost reduction and other advantageous featur es. A general pulse width modulation (PWM) method for c ontrol of 1-phase inverters is presented. The vecto r PWM offers a simple method to select three or four vectors tha t effectively synthesize the desired output voltage,even in presence of voltage oscillations across the two dc-link capacit ors. The influence of different switching patterns on output voltage symmetry,current waveform,switching frequency and common mode voltage can be examined. The paper als o discusses how the use of the wye and delta connecti ons of the motor windings affects the implementatio n of the pulse width modulator.
This document discusses different types of converters that can be used in switched reluctance motors (SRMs) to reduce torque ripple. It begins by outlining the requirements of SRM converters, including allowing phase overlap control and modulating phase voltage. It then describes six converter types - dump converters (R-dump and C-dump), asymmetric, bifilar, auxiliary, and high demagnetization converters. For each type, it provides a circuit diagram and overview of how it dissipates energy during phase commutation. It also models and simulates the performance of SRM drives using the different converter types in MATLAB. The document concludes that asymmetric converters are well-suited for high-speed SRM drives due to their fast current
Harmonic Analysis of Seven and Nine Level Cascade Multilevel Inverter using M...IAES-IJPEDS
The use of multilevel inverters has become popular in recent years for high- power applications. Multilevel Inverters are power converter systems composed by an array of power semiconductor sources that when properly connected and controlled can generate a multistep voltage waveform with variable and controllable frequency, phase and amplitude. This study deals with the comparison of a 7-level inverter with a 9-level inverter system; the voltage source inverters (VSI) are modelled and simulated using MATLAB Simulink and the results are presented. The test results verify the effectiveness of the proposed strategy in terms of computational efficiency as well as the capability of the inverter to produce very low distorted voltage with low-switching losses. This research aims to extend the knowledge about the performance of different clamped multilevel inverter through harmonic analysis. Simulations results validate up to the mark performance of the mentioned topologies.
Regeneration in Variable Frequency Drives and Energy Saving MethodsIRJET Journal
This document discusses methods for regenerating energy from variable frequency drives to save costs. When an induction motor decelerates, it generates electricity that is normally wasted as heat through braking resistors. Regenerative converters can return this energy to the grid instead. Three types are described: regenerative converters use PWM to feed energy back through the supply line; sinusoidal PWM converters regulate voltage while improving power quality; and matrix converters directly convert AC to AC with minimal components. Matrix converters integrate regeneration and driving but have limited voltage transfer. Regenerative converters provide significant utility cost savings, especially for applications with frequent braking like cranes or elevators.
A Modified C-Dump Converter for BLDC Machine Used in a Flywheel Energy Storag...IJERA Editor
This paper presents a modified C-dump converter for brushless DC (BLDC) machine used in the flywheel energy storage system. The converter can realize the energy bidirectional flowing and has the capability to recover the energy extracted from the turnoff phase of the BLDC machine. The principle of operation, modeling, and control strategy of the system has been investigated in the paper. Simulation and experimental results of the proposed system are also presented and discussed.
International Journal of Engineering Research and DevelopmentIJERD Editor
Electrical, Electronics and Computer Engineering,
Information Engineering and Technology,
Mechanical, Industrial and Manufacturing Engineering,
Automation and Mechatronics Engineering,
Material and Chemical Engineering,
Civil and Architecture Engineering,
Biotechnology and Bio Engineering,
Environmental Engineering,
Petroleum and Mining Engineering,
Marine and Agriculture engineering,
Aerospace Engineering.
MODELING, ANALYSIS AND SIMULATION OF POLY-PHASE BOOST CONVERTERijsrd.com
The objective of this paper is to design Poly-phase boost converter which overcomes the problem of high input ripple current and output ripple voltage Digital control is more convenient for such a topology on account of the requirement of synchronization , phase shift operation , current balancing etc. This paper deals on analysis and implementation of four phase boost converter, each is a 35W unit and switched at 100 KHz. The waveforms are observed using MATLAB Simulink.
The document summarizes a study on improving the performance of a two-leg inverter fed brushless DC motor (BLDCM) drive. Key points:
1) A two-leg inverter fed BLDCM drive is proposed that uses only four switches and two current sensors, compared to a conventional three-leg inverter that uses six switches and three current sensors. This reduces switching losses and cost.
2) A MATLAB/Simulink model of the proposed two-leg inverter fed BLDCM drive with two DC input sources is developed.
3) Simulation results show the proposed drive has reduced torque ripple, lower voltage stress, lower current total harmonic distortion, and faster dynamic performance
Design of High-Speed Dynamic Double-Tail ComparatorIJERDJOURNAL
ABSTRACT:- The analog-to-digital converters which are of ultra low-power, area efficient, and high speed converters are made of dynamic regenerative comparators. These comparators can maximize speed and power efficiency. The delay and power dissipation of dynamic comparators are analyzed in this paper. The delays and tradeoff can be explored. The circuit of a conventional double tail comparator in this analysis is modified for fast operation even in different supply voltages. By using power gating technique and adding few transistors, the positive feedback during the regeneration is strengthened in the proposed comparator structure. The delay time can be reduced by providing positive feedback instead of adding few transistors. The analysis results are going to be confirmed on the basis of 0.25-µm CMOS technology. The power consumption and delay time can be significantly reduced based on this analysis. All the simulation are made using TANNER TOOLS, Generic 250nm. The schematic are drawn in the T-SPICE schematic editor.
International Journal of Engineering Research and DevelopmentIJERD Editor
Electrical, Electronics and Computer Engineering,
Information Engineering and Technology,
Mechanical, Industrial and Manufacturing Engineering,
Automation and Mechatronics Engineering,
Material and Chemical Engineering,
Civil and Architecture Engineering,
Biotechnology and Bio Engineering,
Environmental Engineering,
Petroleum and Mining Engineering,
Marine and Agriculture engineering,
Aerospace Engineering.
Variable Speed Operation of Brushless Doubly-Fed Reluctance Machine Drive usi...KiranSinha29
This document discusses model predictive current control (MPCC) for a brushless doubly-fed reluctance machine (BDFRM) drive. MPCC offers a straightforward solution for current control by replacing inner current PI controllers and pulse-width modulator of field oriented control with an optimization-based predictive current controller. Extensive simulations and experimental validations show the proposed MPCC scheme achieves accurate current control and has better performance than field oriented control for the BDFRM drive.
space vector PWM (SVPWM), permanent magnetic synchronous motor(PMSM), field-o...IJERA Editor
Induction Motor are named as workhouse of Industries. Three phase induction motors are widely used in Industrial drives because of their ruggedness, reliability and simplicity in construction. The Induction Motor is fed by a cascaded H-Bridge 7 Level MLI and is controlled by Indirect Field Oriented Control (IFOC) technique. In the current paper, Multi Carrier PWM techniques like PD, POD and APOD are used for switching of multilevel inverters due to their simplicity, flexibility and reduced computational requirements compared to Space Vector Modulation (SVPWM). Dynamic performance of the Induction Motor is analyzed for various carrier based PWM methods. Mathematical model of Pump Load is designed and the performance of the Induction Motor Drive with Pump Load is analyzed using simulation results obtained.
Power Quality Analysis Using Active NPC Multilevel inverter in PV sourced sta...IRJET Journal
This document summarizes a research paper that analyzes power quality in a stand-alone microgrid system using an Active Neutral Point Clamped (ANPC) multilevel inverter sourced by a photovoltaic (PV) system. The document provides background on multilevel inverters and their benefits over traditional inverters. It then describes the proposed ANPC 5-level inverter topology and the simulation of the system in MATLAB/Simulink. The results show that the ANPC multilevel inverter produces lower harmonic distortion than a conventional inverter when used in the microgrid system. Key aspects like switching states, sinusoidal pulse width modulation, and total harmonic distortion are also discussed.
Power Quality Analysis Using Active NPC Multilevel inverter in PV sourced sta...IRJET Journal
This document summarizes a research paper that analyzes power quality in a stand-alone microgrid system using an Active Neutral Point Clamped (ANPC) multilevel inverter sourced by a photovoltaic (PV) system. The document provides background on multilevel inverters and their benefits over traditional inverters. It then describes the proposed ANPC 5-level inverter topology and the simulation of the system in MATLAB/Simulink. The results show that the ANPC multilevel inverter produces lower harmonic distortion than a conventional inverter when used in the microgrid system. Key aspects like switching states, sinusoidal pulse width modulation, and total harmonic distortion are also discussed.
Closed Loop Speed Control of a BLDC Motor Drive Using Adaptive Fuzzy Tuned PI...IJERA Editor
Brushless DC Motors are widely used for many industrial applications because of their high efficiency, high
torque and low volume. This paper proposed an improved Adaptive Fuzzy PI controller to control the speed of
BLDC motor. This paper provides an overview of different tuning methods of PID Controller applied to control
the speed of the transfer function model of the BLDC motor drive and then to the mathematical model of the
BLDC motor drive. It is difficult to tune the parameters and get satisfied control characteristics by using normal
conventional PI controller. The experimental results verify that Adaptive Fuzzy PI controller has better control
performance than the conventional PI controller. The modeling, control and simulation of the BLDC motor have
been done using the MATLAB/SIMULINK software. Also, the dynamic characteristics of the BLDC motor (i.e.
speed and torque) as well as currents and voltages of the inverter components are observed by using the
developed model.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
IRJET- Phase Conversion of VFD based Induction MotorIRJET Journal
This document discusses using a variable frequency drive (VFD) to control the speed of a three-phase induction motor. A VFD allows the motor to operate at variable speeds, which can provide energy savings compared to operating at a single rated speed. The VFD converts incoming single-phase power to three-phase power using a rectifier to produce DC power, then an inverter uses pulse width modulation to generate a three-phase AC output that can be varied in frequency to control motor speed. This setup allows flexible control of the induction motor's speed while improving efficiency over constant speed operation.
Design & Simulation Of 3-Phase, 15-Level Inverter with Reverse Voltage TopologyIJERA Editor
This document describes the design and simulation of a 15-level three-phase inverter with a reverse voltage topology. A new topology is proposed that requires fewer components than existing inverters, particularly at higher voltage levels. This reduces complexity. The 15-level inverter is modeled and simulated in MATLAB. Simulation results show the output voltage waveform, total harmonic distortion within reasonable limits, and voltage and current waveforms. The proposed inverter provides high voltage output with reduced harmonic distortion and lower component count.
IRJET- Simulation of a Doubly Fed Induction Generator based Wind Energy C...IRJET Journal
This document discusses the simulation of a doubly fed induction generator (DFIG) based wind energy conversion system using MATLAB. Key points:
- DFIGs are commonly used in wind energy systems due to advantages like improved efficiency, active and reactive power control, and reduced converter costs.
- In a DFIG system, the stator is directly connected to the grid while the rotor is connected via power electronic converters. Field oriented control is used to control the DFIG.
- The paper presents the mathematical modeling of a DFIG and simulations run in MATLAB, showing outputs like stator current, rotor current, and output power.
- A floating capacitor bridge topology is proposed to control the voltage across the capacitor
Mitigation of Power Quality Issues by Nine Switches UPQC Using PI & ANN with ...IJERA Editor
A nine-switch power converter having two sets of output terminals was recently proposed in place of the traditional back-to-back power converter that uses 12 switches in total. The nine-switch converter has already been proven to have certain advantages, in addition to its component saving topological feature. Despite these advantages, the nine-switch converter has so far found limited applications due to its many perceived performance tradeoffs like requiring an oversized dc-link capacitor, limited amplitude sharing, and constrained phase shift between its two sets of output terminals. Instead of accepting these tradeoffs as limitations, a nine-switch power conditioner is proposed here that virtually ―converts‖ most of these topological short comings into interesting performance advantages. Aiming further to reduce its switching losses, Harmonics, Voltage Sag & Swell an appropriate discontinuous modulation scheme is proposed and studied here in detail to doubly ensure that maximal reduction of commutations is achieved. With an appropriately designed control scheme with PI and ANN with Hysteresis controller then incorporated, the nine-switch converter is shown to favorably raise the overall power quality in Simulation, hence justifying its role as a power conditioner at a reduced cost.
a single stage photovoltaic system for a dual-inverter-fed open-end winding i...Yashwanth kumar
This document presents a single-stage photovoltaic system for driving an open-end winding induction motor for pumping applications. The key aspects are:
1) The system uses a dual-inverter to achieve three-level inversion with a low dc bus voltage, reducing the voltage rating requirements.
2) An integrated control strategy achieves maximum power point tracking from the PV panels and V/f motor speed control.
3) Analytical modeling, simulations, and experimental results are presented to validate the performance of the system under different environmental conditions.
Modeling and Simulation for Transformer Ratio Controlled Slip Power Recovery ...IRJET Journal
This document discusses modeling and simulation of a transformer ratio controlled slip power recovery scheme for an induction motor. Slip power recovery schemes aim to harness the reactive slip power from the motor's rotor circuit that is normally wasted, and feed it back to the main power supply to improve overall system efficiency. The proposed scheme uses a variable ratio transformer to control the rotor speed by changing the amount of voltage fed back to the main bus. Simulation results show that increasing the transformer ratio decreases motor speed linearly while increasing the feedback active power. Reactive power requirements also increase with transformer ratio, reducing the overall system power factor.
IRJET- Designing and Simulation of Multilevel STATCOM on Cascaded TopologyIRJET Journal
This document summarizes the design and simulation of a cascaded multilevel STATCOM topology. It first discusses the need for reactive power compensation and control of power systems. It then describes the cascaded H-bridge multilevel inverter topology used for the STATCOM, noting its advantages over other multilevel inverter types. The document outlines the methodology, discussing control of the STATCOM using pulse width modulation techniques. It also reviews prior implementations of STATCOMs and issues with earlier converter configurations.
The document analyzes different order models for modeling doubly fed induction generators (DFIGs) used in wind turbines, including fifth order, third order, and simplified models. A fifth order model includes stator and rotor dynamics but requires complex calculations. Simplified models exclude elements to reduce computational requirements but lack accuracy. The paper reviews assumptions made in different order models and simulations showing the impact of modeling choices. Simulation results demonstrate that higher order fifth order models capture stator transient behaviors that third order models omit during faults. Accounting for flux saturation provides a more accurate representation of generator behavior.
1) The document describes a system for controlling the speed of a CUK converter-fed BLDC motor using a PI controller.
2) A CUK converter is used to provide power to the BLDC motor and PI control is applied to regulate the output voltage of the CUK converter in order to control the motor speed.
3) Simulation results show that the proposed PI controller is able to effectively control the motor speed while maintaining low current ripple and reducing torque ripples.
A Novel Three Phase Multilevel Inverter with Single DC Link for Induction Mot...IJECEIAES
1) The document presents two configurations of a novel three-phase eleven-level multilevel inverter with a reduced number of switches for induction motor drive applications.
2) Configuration 1 uses separate DC sources for each phase, requiring 24 switches total. Configuration 2 uses a single common DC source for all three phases, also requiring 24 switches.
3) Both configurations are simulated in Matlab/Simulink. Results show the inverter produces a three-phase voltage of 600V peak-to-peak and supplies 50A to an induction motor, driving it at 1400rpm with 10N-m of torque.
This document discusses issues related to integrating distributed energy resources (DER) into electric power grids. It provides background on DER definitions and classifications. It addresses grid integration and interconnection standards, including requirements for steady state and transient operations, protection, and islanding detection. The document outlines considerations for DER protection and control requirements to safely interconnect DER while maintaining grid reliability. It also presents examples of DER installations and research on advanced relay techniques for islanding detection.
This document discusses unintentional islanding of power systems with distributed resources like solar PV. It defines intentional and unintentional islands, and issues with unintentional islands like safety hazards, overvoltages, and loss of protection. Methods to detect unintentional islands are described, like reverse power relays and active techniques. Simulation results show one technique detecting an island within 0.5 cycles. Guidelines for assessing islanding risk are provided, and the future of anti-islanding techniques discussed, like the potential need for multiple active methods with reduced grid stiffness.
MODELING, ANALYSIS AND SIMULATION OF POLY-PHASE BOOST CONVERTERijsrd.com
The objective of this paper is to design Poly-phase boost converter which overcomes the problem of high input ripple current and output ripple voltage Digital control is more convenient for such a topology on account of the requirement of synchronization , phase shift operation , current balancing etc. This paper deals on analysis and implementation of four phase boost converter, each is a 35W unit and switched at 100 KHz. The waveforms are observed using MATLAB Simulink.
The document summarizes a study on improving the performance of a two-leg inverter fed brushless DC motor (BLDCM) drive. Key points:
1) A two-leg inverter fed BLDCM drive is proposed that uses only four switches and two current sensors, compared to a conventional three-leg inverter that uses six switches and three current sensors. This reduces switching losses and cost.
2) A MATLAB/Simulink model of the proposed two-leg inverter fed BLDCM drive with two DC input sources is developed.
3) Simulation results show the proposed drive has reduced torque ripple, lower voltage stress, lower current total harmonic distortion, and faster dynamic performance
Design of High-Speed Dynamic Double-Tail ComparatorIJERDJOURNAL
ABSTRACT:- The analog-to-digital converters which are of ultra low-power, area efficient, and high speed converters are made of dynamic regenerative comparators. These comparators can maximize speed and power efficiency. The delay and power dissipation of dynamic comparators are analyzed in this paper. The delays and tradeoff can be explored. The circuit of a conventional double tail comparator in this analysis is modified for fast operation even in different supply voltages. By using power gating technique and adding few transistors, the positive feedback during the regeneration is strengthened in the proposed comparator structure. The delay time can be reduced by providing positive feedback instead of adding few transistors. The analysis results are going to be confirmed on the basis of 0.25-µm CMOS technology. The power consumption and delay time can be significantly reduced based on this analysis. All the simulation are made using TANNER TOOLS, Generic 250nm. The schematic are drawn in the T-SPICE schematic editor.
International Journal of Engineering Research and DevelopmentIJERD Editor
Electrical, Electronics and Computer Engineering,
Information Engineering and Technology,
Mechanical, Industrial and Manufacturing Engineering,
Automation and Mechatronics Engineering,
Material and Chemical Engineering,
Civil and Architecture Engineering,
Biotechnology and Bio Engineering,
Environmental Engineering,
Petroleum and Mining Engineering,
Marine and Agriculture engineering,
Aerospace Engineering.
Variable Speed Operation of Brushless Doubly-Fed Reluctance Machine Drive usi...KiranSinha29
This document discusses model predictive current control (MPCC) for a brushless doubly-fed reluctance machine (BDFRM) drive. MPCC offers a straightforward solution for current control by replacing inner current PI controllers and pulse-width modulator of field oriented control with an optimization-based predictive current controller. Extensive simulations and experimental validations show the proposed MPCC scheme achieves accurate current control and has better performance than field oriented control for the BDFRM drive.
space vector PWM (SVPWM), permanent magnetic synchronous motor(PMSM), field-o...IJERA Editor
Induction Motor are named as workhouse of Industries. Three phase induction motors are widely used in Industrial drives because of their ruggedness, reliability and simplicity in construction. The Induction Motor is fed by a cascaded H-Bridge 7 Level MLI and is controlled by Indirect Field Oriented Control (IFOC) technique. In the current paper, Multi Carrier PWM techniques like PD, POD and APOD are used for switching of multilevel inverters due to their simplicity, flexibility and reduced computational requirements compared to Space Vector Modulation (SVPWM). Dynamic performance of the Induction Motor is analyzed for various carrier based PWM methods. Mathematical model of Pump Load is designed and the performance of the Induction Motor Drive with Pump Load is analyzed using simulation results obtained.
Power Quality Analysis Using Active NPC Multilevel inverter in PV sourced sta...IRJET Journal
This document summarizes a research paper that analyzes power quality in a stand-alone microgrid system using an Active Neutral Point Clamped (ANPC) multilevel inverter sourced by a photovoltaic (PV) system. The document provides background on multilevel inverters and their benefits over traditional inverters. It then describes the proposed ANPC 5-level inverter topology and the simulation of the system in MATLAB/Simulink. The results show that the ANPC multilevel inverter produces lower harmonic distortion than a conventional inverter when used in the microgrid system. Key aspects like switching states, sinusoidal pulse width modulation, and total harmonic distortion are also discussed.
Power Quality Analysis Using Active NPC Multilevel inverter in PV sourced sta...IRJET Journal
This document summarizes a research paper that analyzes power quality in a stand-alone microgrid system using an Active Neutral Point Clamped (ANPC) multilevel inverter sourced by a photovoltaic (PV) system. The document provides background on multilevel inverters and their benefits over traditional inverters. It then describes the proposed ANPC 5-level inverter topology and the simulation of the system in MATLAB/Simulink. The results show that the ANPC multilevel inverter produces lower harmonic distortion than a conventional inverter when used in the microgrid system. Key aspects like switching states, sinusoidal pulse width modulation, and total harmonic distortion are also discussed.
Closed Loop Speed Control of a BLDC Motor Drive Using Adaptive Fuzzy Tuned PI...IJERA Editor
Brushless DC Motors are widely used for many industrial applications because of their high efficiency, high
torque and low volume. This paper proposed an improved Adaptive Fuzzy PI controller to control the speed of
BLDC motor. This paper provides an overview of different tuning methods of PID Controller applied to control
the speed of the transfer function model of the BLDC motor drive and then to the mathematical model of the
BLDC motor drive. It is difficult to tune the parameters and get satisfied control characteristics by using normal
conventional PI controller. The experimental results verify that Adaptive Fuzzy PI controller has better control
performance than the conventional PI controller. The modeling, control and simulation of the BLDC motor have
been done using the MATLAB/SIMULINK software. Also, the dynamic characteristics of the BLDC motor (i.e.
speed and torque) as well as currents and voltages of the inverter components are observed by using the
developed model.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
IRJET- Phase Conversion of VFD based Induction MotorIRJET Journal
This document discusses using a variable frequency drive (VFD) to control the speed of a three-phase induction motor. A VFD allows the motor to operate at variable speeds, which can provide energy savings compared to operating at a single rated speed. The VFD converts incoming single-phase power to three-phase power using a rectifier to produce DC power, then an inverter uses pulse width modulation to generate a three-phase AC output that can be varied in frequency to control motor speed. This setup allows flexible control of the induction motor's speed while improving efficiency over constant speed operation.
Design & Simulation Of 3-Phase, 15-Level Inverter with Reverse Voltage TopologyIJERA Editor
This document describes the design and simulation of a 15-level three-phase inverter with a reverse voltage topology. A new topology is proposed that requires fewer components than existing inverters, particularly at higher voltage levels. This reduces complexity. The 15-level inverter is modeled and simulated in MATLAB. Simulation results show the output voltage waveform, total harmonic distortion within reasonable limits, and voltage and current waveforms. The proposed inverter provides high voltage output with reduced harmonic distortion and lower component count.
IRJET- Simulation of a Doubly Fed Induction Generator based Wind Energy C...IRJET Journal
This document discusses the simulation of a doubly fed induction generator (DFIG) based wind energy conversion system using MATLAB. Key points:
- DFIGs are commonly used in wind energy systems due to advantages like improved efficiency, active and reactive power control, and reduced converter costs.
- In a DFIG system, the stator is directly connected to the grid while the rotor is connected via power electronic converters. Field oriented control is used to control the DFIG.
- The paper presents the mathematical modeling of a DFIG and simulations run in MATLAB, showing outputs like stator current, rotor current, and output power.
- A floating capacitor bridge topology is proposed to control the voltage across the capacitor
Mitigation of Power Quality Issues by Nine Switches UPQC Using PI & ANN with ...IJERA Editor
A nine-switch power converter having two sets of output terminals was recently proposed in place of the traditional back-to-back power converter that uses 12 switches in total. The nine-switch converter has already been proven to have certain advantages, in addition to its component saving topological feature. Despite these advantages, the nine-switch converter has so far found limited applications due to its many perceived performance tradeoffs like requiring an oversized dc-link capacitor, limited amplitude sharing, and constrained phase shift between its two sets of output terminals. Instead of accepting these tradeoffs as limitations, a nine-switch power conditioner is proposed here that virtually ―converts‖ most of these topological short comings into interesting performance advantages. Aiming further to reduce its switching losses, Harmonics, Voltage Sag & Swell an appropriate discontinuous modulation scheme is proposed and studied here in detail to doubly ensure that maximal reduction of commutations is achieved. With an appropriately designed control scheme with PI and ANN with Hysteresis controller then incorporated, the nine-switch converter is shown to favorably raise the overall power quality in Simulation, hence justifying its role as a power conditioner at a reduced cost.
a single stage photovoltaic system for a dual-inverter-fed open-end winding i...Yashwanth kumar
This document presents a single-stage photovoltaic system for driving an open-end winding induction motor for pumping applications. The key aspects are:
1) The system uses a dual-inverter to achieve three-level inversion with a low dc bus voltage, reducing the voltage rating requirements.
2) An integrated control strategy achieves maximum power point tracking from the PV panels and V/f motor speed control.
3) Analytical modeling, simulations, and experimental results are presented to validate the performance of the system under different environmental conditions.
Modeling and Simulation for Transformer Ratio Controlled Slip Power Recovery ...IRJET Journal
This document discusses modeling and simulation of a transformer ratio controlled slip power recovery scheme for an induction motor. Slip power recovery schemes aim to harness the reactive slip power from the motor's rotor circuit that is normally wasted, and feed it back to the main power supply to improve overall system efficiency. The proposed scheme uses a variable ratio transformer to control the rotor speed by changing the amount of voltage fed back to the main bus. Simulation results show that increasing the transformer ratio decreases motor speed linearly while increasing the feedback active power. Reactive power requirements also increase with transformer ratio, reducing the overall system power factor.
IRJET- Designing and Simulation of Multilevel STATCOM on Cascaded TopologyIRJET Journal
This document summarizes the design and simulation of a cascaded multilevel STATCOM topology. It first discusses the need for reactive power compensation and control of power systems. It then describes the cascaded H-bridge multilevel inverter topology used for the STATCOM, noting its advantages over other multilevel inverter types. The document outlines the methodology, discussing control of the STATCOM using pulse width modulation techniques. It also reviews prior implementations of STATCOMs and issues with earlier converter configurations.
The document analyzes different order models for modeling doubly fed induction generators (DFIGs) used in wind turbines, including fifth order, third order, and simplified models. A fifth order model includes stator and rotor dynamics but requires complex calculations. Simplified models exclude elements to reduce computational requirements but lack accuracy. The paper reviews assumptions made in different order models and simulations showing the impact of modeling choices. Simulation results demonstrate that higher order fifth order models capture stator transient behaviors that third order models omit during faults. Accounting for flux saturation provides a more accurate representation of generator behavior.
1) The document describes a system for controlling the speed of a CUK converter-fed BLDC motor using a PI controller.
2) A CUK converter is used to provide power to the BLDC motor and PI control is applied to regulate the output voltage of the CUK converter in order to control the motor speed.
3) Simulation results show that the proposed PI controller is able to effectively control the motor speed while maintaining low current ripple and reducing torque ripples.
A Novel Three Phase Multilevel Inverter with Single DC Link for Induction Mot...IJECEIAES
1) The document presents two configurations of a novel three-phase eleven-level multilevel inverter with a reduced number of switches for induction motor drive applications.
2) Configuration 1 uses separate DC sources for each phase, requiring 24 switches total. Configuration 2 uses a single common DC source for all three phases, also requiring 24 switches.
3) Both configurations are simulated in Matlab/Simulink. Results show the inverter produces a three-phase voltage of 600V peak-to-peak and supplies 50A to an induction motor, driving it at 1400rpm with 10N-m of torque.
This document discusses issues related to integrating distributed energy resources (DER) into electric power grids. It provides background on DER definitions and classifications. It addresses grid integration and interconnection standards, including requirements for steady state and transient operations, protection, and islanding detection. The document outlines considerations for DER protection and control requirements to safely interconnect DER while maintaining grid reliability. It also presents examples of DER installations and research on advanced relay techniques for islanding detection.
This document discusses unintentional islanding of power systems with distributed resources like solar PV. It defines intentional and unintentional islands, and issues with unintentional islands like safety hazards, overvoltages, and loss of protection. Methods to detect unintentional islands are described, like reverse power relays and active techniques. Simulation results show one technique detecting an island within 0.5 cycles. Guidelines for assessing islanding risk are provided, and the future of anti-islanding techniques discussed, like the potential need for multiple active methods with reduced grid stiffness.
The document discusses several methods for detecting power islands in grid-connected distributed generation systems. Passive detection schemes have a large non-detection zone while active methods can degrade power quality. Intelligent methods that use artificial intelligence techniques like neural networks, fuzzy logic, genetic algorithms and expert systems show promise for quickly and accurately detecting and classifying islanding conditions. The key advantages of these methods are their ability to learn adaptively and generalize while accurately detecting islanding conditions.
This document provides an overview of a course on power generation systems. The course covers conventional power sources like thermal and hydroelectric plants as well as non-conventional renewable sources like solar and wind. It discusses different methods of power generation including using steam to turn turbines, using the kinetic energy of moving water or wind, and exploiting nuclear reactions. The document compares various energy sources based on their initial costs, running costs, limitations, and sustainability. Students will learn about electrical power generation and the key players and sources that make up Pakistan's power sector.
This document discusses the implications of distributed generation islanding on power system dynamics. It begins by defining islanding as the phenomenon where a distributed generator continues to power a location even after that location is electrically isolated from the central distribution network. If unintentional islanding occurs, it can pose safety hazards and damage equipment if the distributed generator's voltage and frequency are not properly regulated. The document also discusses out-of-phase reclosing, which produces high transient currents that can damage equipment. It then examines various active anti-islanding methods and notes their dynamic impacts, such as unnecessary tripping from undervoltage events. While anti-islanding protection prevents problems now, the document warns its effects could degrade power quality and stability as distributed
The document provides installation instructions and specifications for capacitors, including that a minimum 50mm gap is required between capacitors, the air temperature must not exceed 65 degrees Celsius, and the bottom of copper bars should be at least 180mm above capacitor terminals to avoid magnetic interference. It also lists technical parameters for the capacitors such as voltage, frequency, amps, weight, and individual kvar and MFD specifications for 5 capacitors along with an internal wiring diagram and date.
This document discusses the construction and operation of synchronous machines. It describes how synchronous generators have rotors that produce a rotating magnetic field from DC current in field windings. Synchronous motors have stators that produce a rotating magnetic field to turn the rotor. Large generators use brushless exciters to supply DC current to rotor windings without mechanical contact. Equivalent circuits are presented showing how armature reaction affects the relationship between internally generated and terminal voltages. Phasor diagrams illustrate voltage and current relationships for different power factors.
This document provides an overview of a lecture on DC motors. It begins with preliminary notes stating that DC motors have applications in automobiles, aircraft and portable electronics due to their ability to easily control speed. It then discusses the simplest DC machine, which consists of a single rotating loop of wire. The document explains how a voltage is induced in the rotating loop and how a commutator can be added to convert the alternating voltage to a direct voltage. It further discusses how this simplest machine demonstrates the basic principles of induced voltage, torque, and commutation that apply to real DC machines.
Synchronous motors and generators operate by synchronizing the rotation of the rotor's magnetic field with the rotating magnetic field produced by the stator windings. Synchronous motors are used for constant-speed applications like propulsion for large ships. They work by locking the rotor's magnetic field to the rotating stator field. Synchronous generators can be produced by transitioning a synchronous motor driven by a turbine from motor to generator operation as the power angle shifts from negative to positive.
Basic Power Electronics Concepts_Ozipineci_ORNL.pdfgulie
This document provides an introduction to power electronics. It defines power electronics as technology used to change the characteristics of electrical power to suit applications. The document outlines the history and types of power semiconductor devices like diodes, thyristors, MOSFETs and IGBTs. It also describes different types of power converters including rectifiers, inverters, and DC-DC converters. Thermal management of power devices is also discussed.
Electrical Engineering Objective Type Questions.pdfgulie
This document contains a list of objective type questions for the Electrical Engineering department at Government College of Engineering in Bargur, prepared by assistant professor V. Arivumani. It includes 875 total questions organized under various topics related to electrical engineering, such as DC generators, DC motors, transformers, induction motors, synchronous motors, transmission and distribution, and cables. The questions cover concepts like generator construction, winding types, armature reaction, commutation, and parallel operation of generators. Sample questions and answers are provided for the topic of DC generators.
This document provides job hunting techniques for those seeking employment in the United Arab Emirates (UAE). It outlines steps such as defining one's career interests, obtaining necessary documents like a passport and degree attestation, creating a strong resume and cover letter, applying for jobs online from home country or during a visit to UAE, and preparing for interviews. Useful online resources and job sites are also listed to facilitate the job searching process in UAE.
This document presents a fractional order PID controller (FOPID)-Toolbox to design robust fractional PID controllers. The toolbox uses nonsmooth optimization techniques to optimize the parameters of fractional PIαDβ and (PID)n controllers to achieve a desired crossover frequency and phase margin. The goal is to develop a systematic method to optimize the parameters of these fractional order controllers based on expressing the control problem and requirements in terms of a desired open-loop response and using a loop shaping configuration. An algorithm is proposed that initializes the fractional orders, computes the gradient with respect to the orders, and iteratively updates the orders using steepest descent until convergence.
This document describes research into using a fractional order PID (FOPID) controller to control voltage fluctuations in an islanded microgrid with a single power source. The proposed FOPID controller has more tuning parameters than a standard PID controller, allowing it to better regulate the microgrid's output voltage under different load conditions and uncertainties. The controller is designed using an optimization technique to maximize system performance. Simulation results show the FOPID controller is effective at reducing voltage fluctuations and provides a fast, robust response for the microgrid system.
This document discusses unintentional islands in power systems with distributed resources and methods to prevent them. It defines types of islands and issues they can cause. It outlines standard testing and requirements for distributed resources to detect and cease energizing an unintentional island within 2 seconds. Various passive, active and communication-based anti-islanding protection methods are described to meet this requirement.
SVM-plus-Phase-Shift Modulation Strategy for Single-Stage.pdfgulie
This document proposes a new modulation strategy called SVM-plus-phase-shift (SVM-PS) modulation for a single-stage three-phase resonant AC-DC matrix converter with an LCL resonant tank. The strategy aims to achieve unity power factor and flexible control of active and reactive power transfer. It derives the relationship between switch states and line-frequency phase currents based on the fundamental component of the tank current. This allows simple control of current amplitude and phase via modulation of the AC and DC side switches based on voltage and current references. Simulation results show the proposed strategy reduces current distortion and ripple compared to conventional SVM.
Grid Converters for Photovoltaic and Wind Power Systems - 2010 - Teodorescu -...gulie
This document summarizes space vector transformations of three-phase systems. It discusses symmetrical components analysis in the frequency and time domains, which allows decomposition of an unbalanced three-phase system into positive, negative, and zero sequence components. It also describes Clarke's transformation to a stationary αβ0 reference frame, which defines three independent real components from the complex positive and negative sequence components.
This document discusses space vector pulse width modulation (SVPWM) techniques for multilevel inverters. It begins by introducing SVPWM and explaining that it provides advantages over sinusoidal PWM, including better fundamental output voltage and improved harmonic performance. It then defines two-dimensional and three-dimensional space vectors and discusses how SVPWM can be implemented in both 2D and 3D. The document focuses on SVPWM for three-leg voltage source inverters, describing the voltage space vectors and how SVPWM can be used to synthesize the required output voltage vector through PWM of the switching state vectors.
This document provides an introduction to using the ATP/EMTP software for simulating electrical systems transients. It discusses how to create data files for simulations using either ATPDraw, a graphical preprocessor, or by directly editing text files. It also describes running simulations and viewing results. The document is intended to introduce beginners to the ATP/EMTP software by following existing manuals on its usage and capabilities. It emphasizes that expertise requires experience working with the software and suggests consulting manuals and experts for in-depth knowledge of complex simulations.
Electric vehicle and photovoltaic advanced roles in enhancing the financial p...IJECEIAES
Climate change's impact on the planet forced the United Nations and governments to promote green energies and electric transportation. The deployments of photovoltaic (PV) and electric vehicle (EV) systems gained stronger momentum due to their numerous advantages over fossil fuel types. The advantages go beyond sustainability to reach financial support and stability. The work in this paper introduces the hybrid system between PV and EV to support industrial and commercial plants. This paper covers the theoretical framework of the proposed hybrid system including the required equation to complete the cost analysis when PV and EV are present. In addition, the proposed design diagram which sets the priorities and requirements of the system is presented. The proposed approach allows setup to advance their power stability, especially during power outages. The presented information supports researchers and plant owners to complete the necessary analysis while promoting the deployment of clean energy. The result of a case study that represents a dairy milk farmer supports the theoretical works and highlights its advanced benefits to existing plants. The short return on investment of the proposed approach supports the paper's novelty approach for the sustainable electrical system. In addition, the proposed system allows for an isolated power setup without the need for a transmission line which enhances the safety of the electrical network
Using recycled concrete aggregates (RCA) for pavements is crucial to achieving sustainability. Implementing RCA for new pavement can minimize carbon footprint, conserve natural resources, reduce harmful emissions, and lower life cycle costs. Compared to natural aggregate (NA), RCA pavement has fewer comprehensive studies and sustainability assessments.
Embedded machine learning-based road conditions and driving behavior monitoringIJECEIAES
Car accident rates have increased in recent years, resulting in losses in human lives, properties, and other financial costs. An embedded machine learning-based system is developed to address this critical issue. The system can monitor road conditions, detect driving patterns, and identify aggressive driving behaviors. The system is based on neural networks trained on a comprehensive dataset of driving events, driving styles, and road conditions. The system effectively detects potential risks and helps mitigate the frequency and impact of accidents. The primary goal is to ensure the safety of drivers and vehicles. Collecting data involved gathering information on three key road events: normal street and normal drive, speed bumps, circular yellow speed bumps, and three aggressive driving actions: sudden start, sudden stop, and sudden entry. The gathered data is processed and analyzed using a machine learning system designed for limited power and memory devices. The developed system resulted in 91.9% accuracy, 93.6% precision, and 92% recall. The achieved inference time on an Arduino Nano 33 BLE Sense with a 32-bit CPU running at 64 MHz is 34 ms and requires 2.6 kB peak RAM and 139.9 kB program flash memory, making it suitable for resource-constrained embedded systems.
ACEP Magazine edition 4th launched on 05.06.2024Rahul
This document provides information about the third edition of the magazine "Sthapatya" published by the Association of Civil Engineers (Practicing) Aurangabad. It includes messages from current and past presidents of ACEP, memories and photos from past ACEP events, information on life time achievement awards given by ACEP, and a technical article on concrete maintenance, repairs and strengthening. The document highlights activities of ACEP and provides a technical educational article for members.
A SYSTEMATIC RISK ASSESSMENT APPROACH FOR SECURING THE SMART IRRIGATION SYSTEMSIJNSA Journal
The smart irrigation system represents an innovative approach to optimize water usage in agricultural and landscaping practices. The integration of cutting-edge technologies, including sensors, actuators, and data analysis, empowers this system to provide accurate monitoring and control of irrigation processes by leveraging real-time environmental conditions. The main objective of a smart irrigation system is to optimize water efficiency, minimize expenses, and foster the adoption of sustainable water management methods. This paper conducts a systematic risk assessment by exploring the key components/assets and their functionalities in the smart irrigation system. The crucial role of sensors in gathering data on soil moisture, weather patterns, and plant well-being is emphasized in this system. These sensors enable intelligent decision-making in irrigation scheduling and water distribution, leading to enhanced water efficiency and sustainable water management practices. Actuators enable automated control of irrigation devices, ensuring precise and targeted water delivery to plants. Additionally, the paper addresses the potential threat and vulnerabilities associated with smart irrigation systems. It discusses limitations of the system, such as power constraints and computational capabilities, and calculates the potential security risks. The paper suggests possible risk treatment methods for effective secure system operation. In conclusion, the paper emphasizes the significant benefits of implementing smart irrigation systems, including improved water conservation, increased crop yield, and reduced environmental impact. Additionally, based on the security analysis conducted, the paper recommends the implementation of countermeasures and security approaches to address vulnerabilities and ensure the integrity and reliability of the system. By incorporating these measures, smart irrigation technology can revolutionize water management practices in agriculture, promoting sustainability, resource efficiency, and safeguarding against potential security threats.
International Conference on NLP, Artificial Intelligence, Machine Learning an...gerogepatton
International Conference on NLP, Artificial Intelligence, Machine Learning and Applications (NLAIM 2024) offers a premier global platform for exchanging insights and findings in the theory, methodology, and applications of NLP, Artificial Intelligence, Machine Learning, and their applications. The conference seeks substantial contributions across all key domains of NLP, Artificial Intelligence, Machine Learning, and their practical applications, aiming to foster both theoretical advancements and real-world implementations. With a focus on facilitating collaboration between researchers and practitioners from academia and industry, the conference serves as a nexus for sharing the latest developments in the field.
Using recycled concrete aggregates (RCA) for pavements is crucial to achieving sustainability. Implementing RCA for new pavement can minimize carbon footprint, conserve natural resources, reduce harmful emissions, and lower life cycle costs. Compared to natural aggregate (NA), RCA pavement has fewer comprehensive studies and sustainability assessments.
2. in six-step mode. In a five-phase drive the most dominant
pulsating torque is a 10th harmonic and as such for n-phase
it is 2nth harmonic torque. Other advantages are lower
per-leg current rating for the same voltage rating (due to lower
current rating series and parallel switch combination is not
required and hence cheaper solution is achieved), greater fault
tolerance (machine can start and run even with loss of one or
more phase supply), lower dc link current harmonics and lower
harmonic losses.
Multiphase electric machines are becoming more popular in
the range of medium- and high-power applications [1–5]. Con-
sidering an inverter-fed high-power electric motor with power
rating exceeding the available rating of power semiconductor
switches, the designer has to increase the number of feeding
inverters. This implies higher number of phases on the stator
of the electric motor as well. Two solutions can be sought for
segmenting the power, either increase the number of phases
in multiple of three (parallel-connected multiple three-phase
inverters) or increase the number of legs of inverter with each
leg handling a power of P/n (P is the total power, and n is the
number of phases). The design solutions are shown in Fig. 15.1.
The solutions given in Fig. 15.1B have n number of parallel-
connected three-phase inverters each carrying power of P/n.
The supplied motor has multiple three-phase windings with
separate neutral points. The major advantage of these off-
the-shelf standard three-phase inverters is to supply the motor
with each inverter handling lower amount of power. However,
the major issue of this drive topology is the circulating current
due to the voltage mismatch of each three-phase inverter. The
electric motor in this case is called asymmetrical or split-phase
motor. This solution is preferred and most widely used in
industries because of the fact that the three-phase system solu-
tion is well proved and a mature technology:
Solution of Fig. 15.1C, in contrast to the previous solution,
works with a single inverter of n-phases supplying electric
motor of n-phase. Each phase or leg now handles P/n power,
and the circulating current is absent. The electric motor in this
case is called symmetrical n-phase motor. This solution is also
employed in high-power marine drive applications [6].
Reliability and fault tolerance are other driving forces leading
to the development of multiphase system. Due to high phase
number, fault tolerance is inherently guaranteed, which is of
high importance in safety critical applications such as ship pro-
pulsion, more electric aircrafts, electric vehicles, and industrial
setup where production loss is critical such as oil and gas plants
and military. The multiphase motor drive guarantees continu-
ous operation, however, with degraded performance under
fault conditions. The higher the phase number, the better is
the performance during faults. This make them highly attrac-
tive in applications mentioned above [7,8].
According to classical electric machine theory, the air-gap
flux harmonic content improves and becomes close to sinusoi-
dal with the increase in the number of phases. The improved
flux density waveform leads to: (i) reduced rotor losses due
to flux pulsation and eddy currents (this has importance for
high-speed permanent magnet machines since the eddy current
losses are very high at high speed in such kind of machines) and
(ii) improved torque quality with reduced amplitude of torque
pulsation that occurs at higher frequency (this is very impor-
tant when machine is subjected to high distorted current,
and limits are enforced on the maximum allowable torque
pulsation).
Multiphase generators, specially five phases and more, have
started to find a slot in the market due to their advantages over
three-phase counterpart [9,10]. This multiphase system could
be more suitable for direct drive wind energy, microturbines,
and electric vehicle applications since the need for gears can
be minimized. Multipulse rectifiers are employed, which have
Three-phase
Motor
Three-phase
DC/
AC converter
P
V
DC
(A)
n-Phase motor
(n=multiple
of 3)
Three-phase
DC/
AC converter
P/n
V
DC
Three-phase
DC/
AC converter
V
DC
Three-phase
DC/
AC converter
V
DC
P/n
P/n
(B)
n-Phase motor
n-Phase DC/AC
converter
P/n-per phase
V
DC
(C)
FIG. 15.1 (A) Three-phase drive, (B) multiple three-phase drive, and
(C) multiphase drive.
458 A. Iqbal et al.
3. the ability to reduce the line current harmonic distortion and
normally do not require any LC filters or power factor improve-
ment devices. Multipulse DC can be obtained either by increas-
ing the number of phases of the converter or by the use of
phase-shifting transformer along with special secondary wind-
ing connections in the conventional six-pulse rectifiers. In drive
application, the use of phase-shifting transformer provides an
effective means to block common-mode voltages generated by
the rectifier and inverter, which would otherwise appear on
motor terminals, leading to a premature failure of machine
winding insulation. Normally AC-DC converters are classified
into power factor control rectifiers operated at high switching
frequency and line-commutated rectifiers (uncontrolled or con-
trolled) operated at power frequency or generated frequency.
The multiphase line-commutated converter normally offers
simple control, simple construction, and low cost but suffers
from poor input power factor, low input current THD, and uni-
directional current flow. The shortcoming of line-commutated
rectifiers is overcome by the use of high-switching-frequency
PWM rectifiers, voltage-source rectifiers, or current-source rec-
tifiers, but the switch current and voltage limitation may restrict
the use of PWM rectifiers in high-power applications.
Multiphase DC-AC voltage-source inverter is obtained from
three-phase voltage-source inverter by adding extra legs (each
leg has two switches in two-level inverter and a higher number
of switches for multilevel inverter). The two switches of the
same leg are complimentary in operation (i.e., when upper
switch is on, the lower switch must be off and vice versa).
The power switches can assume only two states, that is, on
(called level 1) or off (called level 0). Hence, as such for n-phase
inverter, there can be 2n
number of switching states. Consider-
ing a three-phase inverter, the number of switching states are 8,
and, for example, for a nine-phase inverter, the number of
switching states are 29
¼512 [5]. It is seen that the number of
switching states increases significantly with the increase in
the number of phases or legs. Higher numbers of switching
states offer flexibility in devising control techniques. Thus, mul-
tiphase inverter control has several degrees of flexibility in con-
trol. Multiphase inverter can be controlled using different
PWM techniques such as carrier-based sinusoidal PWM, har-
monic injection PWM, selective harmonic PWM, hybrid PWM,
and space-vector PWM. Each method can produce different
output magnitudes. Simple carrier-based PWM for multiphase
inverters works exactly the same as for three-phase inverters.
The maximum possible output phase-to-neutral voltage is
0.5 VDC, where VDC is DC-link voltage magnitude for multi-
phase inverter [1]. However, the output phase-to-neutral volt-
age magnitude varies for different phase numbers when using
space-vector PWM. Nevertheless, the output phase-to-neutral
voltage of multiphase inverters is less than that of a three-phase
inverter. Multiphase inverter space vectors are transformed into
multiple orthogonal planes, and control is implemented in
order to regulate each plane vectors. In multiphase variable-
speed drives (with distributed winding multiphase machine),
torque is controlled only from one plane vector (d-q), and
the rest of the plane vectors produce distortion and hence need
to be minimized using PWM techniques. When concentrated
winding multiphase machines are supplied using multiphase
voltage-source inverters, all plane vectors are used to enhance
the torque production. This is a unique feature of concentrated
winding multiphase machine not available in three-phase
machines. When implementing high-performance control such
as vector control and direct torque control, higher control flex-
ibility is available, and different solutions can be implemented.
Multiphase AC-AC converter more popularly known as mul-
tiphase matrix converter (MPMC) is also formulated by adding
extra legs in three-phase matrix converter configuration. They
are classified as direct matrix converters (DMC) and indirect
matrix converters (IMC). Each converter leg has three bidirec-
tional power switches each connected to one phase of the utility
grid system, and at the output, load is connected. The input is
fixed voltage and fixed frequency supply, while the output is of
variable voltage and variable frequency. There are configura-
tions where the number of input phases is three while the output
phase are more than three and vice versa [4,5]. The multiphase
matrix converter encompasses the advantages of three-phase
matrix converters and multiphase systems. The major applica-
tion areas are envisaged in multiphase wind energy system.
A matrix converter can be seen as an array of mn bidirec-
tional power semiconductor switches that can transform
m-phase fixed voltage and fixed frequency input to n-phase var-
iable voltage and variable frequency output without intermedi-
ate DC conversion stage. The input side of a matrix converter is
voltage fed, while the output side is current fed, and hence, an
inductive filter is required at the output side, and a capacitive
filter is used at the input side. As the load is itself of inductive
nature, the requirement of output filter diminishes. The size of
the input filter used in matrix converter is significantly smaller
than an equivalent voltage-source inverter.
Considering an mn matrix converter, the number of
switching states is 2mn
. Large numbers of switching states
are produced; however, not all of them are useful. Due to the
nature of input (being voltage source) and output (being cur-
rent source), the input should not short-circuited, and the out-
put should not be open-circuited. As a consequence, only one
switch in each leg conducts at one instant of time, and hence, a
usable number of switching states are mn
. In matrix converter,
the output (sinusoidal) is formed from input (sinusoidal),
and hence, output can assume any level depending upon the
instantaneous value of the input. This makes the switching
logic of matrix converter quite complex. The output voltage
of a three-phase input and three-phase output matrix converter
is 86.6% of the input voltage. The output-voltage magnitude
reduces for higher phase number of outputs; for example,
for a three-phase input and five-phase output matrix con-
verter, it is 78.86% [11], and this value decreases further with
increase in the output number of phases. The output voltage
becomes higher than the input for mn matrix converter
459
15 Multiphase Converters
4. for mn; for example, for a five-phase input and three-phase
output, it is 104.4%, and this value further increases as m is
increased [4,12].
Multiphase matrix converters are constructed from bidirec-
tional power switches that are realized in the same way as a
three-phase matrix converter. The modulation strategies are
complex and can be built upon the concept of three-phase
matrix converter. However, significant challenges exist in
obtaining proper modulation technique for a multiphase matrix
converter. Some modulation strategies discussed in the litera-
ture are carrier-based PWM, space-vector PWM, and direct-
duty-ratio-based PWM [13–19].
Multiphase matrix converters find its application in wind
energy generation [20], power system [21,22], and ship propul-
sion [23]. When used in multiphase energy generation, usually
the input side of the matrix converter is of higher phase, and
the output side is three-phase connected to either utility grid
or feeding isolated load. A 27-phase input and 3-phase output
matrixconverterof100 MWpower rating ispresented in[24,25].
Present-day advancement in powering processors invariably
uses multiphase buck converter topology because of higher out-
put current and low-voltage requirement. Single-phase buck
converter works well for low-voltage applications with currents
up to 25 A. Higher filtering requirement and efficiency issue
limits the use of single-phase topology in applications such
as voltage regulator module (VRM). Interleaving as technically
known reduces ripple currents at the input and output.
A multiphase buck converter reduces considerably the i2
R cur-
rent power dissipation in the controlled switches and inductors.
The distribution of current in various paths in a multiphase
converter reduces the current magnitude through the switches,
thereby reducing the switching losses. The output filter require-
ment decreases in a multiphase implementation due to the
higher frequency of ripple current as a result of ripple current
cancelation in the power stage for each phase. The single-phase
implementation has much higher ripple content. Load tran-
sient performance is also better because of the reduction in
energy stored in each output inductor. The lower the ripple cur-
rent is, the less the perturbation will be. The input capacitors
supply all the input current to the buck converter if the input
wire to the converter is inductive. Improvement in multiphase
topologies and their control strategies promise improved per-
formance compared to the conventional multiphase buck
converter.
This chapter is organized into five different sections covering
the topologies, operation, and control of different types of
multiphase power converters. Section 15.2 describes the types
and classifications of different multiphase power converters.
Section 15.3 is dedicated to AC-DC converters considering
multiphase and multipulse output. Section 15.4 is devoted
to DC-AC converters especially focusing on five-phase and
seven-phase voltage-source inverter. Section 15.5 covers the
description of multiphase AC-AC converters, and multiphase
DC-DC converters are discussed in Section 15.6.
15.2 Types and Topologies of Multiphase
Converters
The requirements for the current and voltage continue to
increase with an increase in power level, and systems become
more and more complex. The amount of current/voltage of
power source to meet such requirements usually needs a com-
bination of several power controllers to improve the thermal
stress of the individual power components. The driving mech-
anism for this combination leaves one with two choices: single
phase or multiphase.
Multiphase converters reduce the input and output current
ripples by interleaving the two or more stages of power con-
verters. By increasing the phase number, the output-voltage
ripple and the input capacitor size can be curtailed without
increasing the switching frequency of the power devices. Load
dynamic performance is significantly improved during tran-
sients due to lower-output-voltage ripple and smaller output
inductors. The low switching losses and driver circuit losses
of power semiconductor devices at relatively low switching fre-
quency and the reduced power losses due to equivalent series
resistance (ESR) of the capacitors help achieve overall high effi-
ciency of converters. For multioutput applications, multiphase
converters may also provide the benefit of smaller input side
capacitors.
Single-phase versus multiphase converters are as follows:
(1) Single-phase converters work well for low voltages and
up to certain amount of current say about 25 A, but
power dissipation and efficiency start to become an
issue at higher currents. One suitable approach is to
develop multiphase converters [26].
(2) The output filter requirements decrease in multiphase
implementation due to the reduced current in the power
stage for each phase. Compared with single-phase
approach, the inductance and inductor size are drasti-
cally reduced because of lower average current and
lower saturation current.
(3) Ripplecurrentcancelationinthe outputfilterstageresults
in a reduced ripple voltage across the output capacitor
compared with single-phase approach. This is another
reason why a multiphase converter is preferred.
(4) Load transient performance is improved due to the
reduction of energy stored in each output inductor.
The reduction in ripple voltage as a result of current
cancelation contributes to minimal output-voltage over-
shoot and undershoots because many cycles will pass
before the loop responds. The lower the ripple current
is, the less the perturbation will be.
Like single-phase or three-phase converters, multiphase con-
verters are classified as AC-DC, DC-AC, DC-DC, and AC-AC
converters. Multiphase converters are simple extension of
three-phase converters. As far as hardware is concerned, there
460 A. Iqbal et al.
5. is not much difference. However, the control complexity
increases manyfold with the increase in the number of phases.
There are further classifications in these converters. The classi-
fication of multiphase converters is shown in respective section.
15.2.1 Multiphase AC-DC Converters
A significant amount of work is done on developing novel
topologies of multipulse AC-DC converters since they have
huge potential applications for unidirectional and bidirectional
power flow starting from six pulses to a large number of pulses.
The major advantage of adopting a higher pulse number is the
current ripple reduction.
The novel configurations in multiphase AC-DC converter
were developed of unidirectional and bidirectional topologies
with three or more number of phases. Classification of multi-
phase AC-DC converters is shown in Fig. 15.2, which is based
on power flow, number of pulse used, isolated and nonisolated
topologies, and various techniques used to improve AC current
profile and output DC voltage waveform [27]. Based on the
application and requirements, some systems require unidirec-
tional power flow, and some require bidirectional power flow.
Unidirectional systems use diode rectifiers and transformer
circuit configurations in isolated and nonisolated topologies.
The unidirectional topologies have configurations of six pulses
and its multiple. If the voltage difference is more between input
and output, then isolated configuration is useful, and if the
difference is less, nonisolated topologies are used. However,
these are further classified as bridge and full-wave rectifiers.
These types of full-wave multipulse converters (MPC) can also
be further classified whether it uses double star or tapped poly-
gon transformer secondary to create twelve phases to feed full-
wave diode rectifiers. Both configurations have their own merits
and demerits, but both MPC configurations show the same per-
formance in terms of device and transformer utilization.
On the other hand, the bidirectional AC-DC converters have
the power flow from AC mains to DC output or vice versa and
normally use thyristors with phase angle control to obtain wide
varying DC output voltages. These MPCs use multiple winding
transformers to generate higher number of the phases. Like
unidirectional, these MPCs are also divided as isolated and
nonisolated. These are mainly used to feed DC motor drives
and synchronous motor drives.
15.2.2 Multiphase DC-DC Converters
Multiphase topologies can be configured as a step-down
(buck), step-up (boost), buck boost, and even forward con-
verter. A multiphase DC/DC converter according to the pre-
sent invention includes a plurality of DC/DC converters
whose outputs are connected in common to supply electric
power to a load and a load state detection portion that detects
a state of the load connected to the plurality of DC/DC con-
verters and outputs a detection result. Multiphase DC-DC
converters classification is shown in Fig. 15.3.
15.2.3 Multiphase DC-AC Converters
Multiphase DC-AC converters are the main source of multi-
phase adjustable-speed drives. The major driving force behind
the adoption of multiphase motor drive is due to the power
segmentation in large number of converter legs. The power
switching devices have limited voltage- and current-handling
capabilities. Hence, when used in high-power application,
series-and parallel combination of devices are required. This
is cumbersome solution because of dynamic voltage sharing
problem among the series-/parallel-connected power switching
devices. Better solution is obtained when the power per phase
or per leg is reduced by increasing the number of phases or
number of legs, and this is termed as multiphase DC-AC
Multiphase AC-DC
converters
Diode rectifiers
(uncontrolled)
Single way Isolated
SCRs/IGBTs
(controlled)
Non isolated Isolated Non isolated
Bridge type Full wave Bridge type Full wave 6/12/18/24 pulse
converters
6/12/18/24 pulse
converters
6/12/18/24 pulse
converters
12/18 pulse
converters
6/12/24 pulse
converters
6/12/18/24 pulse
converters
FIG. 15.2 Multiphase AC-DC converter classification.
461
15 Multiphase Converters
6. inverters. Multiphase DC-AC inverters are simple in design as
they are simple extension of three-phase DC-AC inverter.
However, they offer large degree of switching redundancies
and hence great flexibility in control. Although control
becomes complex, the performance is improved manifold.
Multiphase DC-AC inverters can be built in the same topolo-
gies as that of their three-phase counterparts and hence have
the same calcifications and types. Multiphase AC-DC con-
verters normally classified as shown in Fig. 15.4.
First version of multiphase inverter technology is five-phase
VSI fed to star-connected five-phase load. Five-phase VSI
configuration found application for five-phase induction
machine and synchronous machine drives. Six-phase inverter
configuration was built with two two-level standard three-
phase VSIs, with two separate DC sources fed to dual three-
phase induction motor. Seven-phase VSI fed to star-connected
seven-phase load based on multiple space-vector modulation
and seven-phase VSI configuration found applications for
seven-phase permanent magnet synchronous and synchronous
reluctance motor drives. Fig. 15.5 shows simple five-phase
induction motor drive.
Multiphase inverters are also classified as cascaded H-bridge,
diode clamped, and flying capacitor topologies. They can also
be built in hybrid configuration. Multiphase impedance-source
inverters (ZSI) and quasi impedance-source inverters (qZSI)
are also reported in the literature [28]. ZSI and qZSI are special
inverters that have the capability of boosting the source voltage
and inverting DC to AC simultaneously. The boosting can be as
high as 200%–300%. They are popular in solar PV applications
since boosting and inversion is done in a single stage. Multi-
phase ZSI/qZSI is used to feed multiphase motor drives.
15.2.4 Multiphase AC-AC Converters
MultiphaseAC-AC converters are generallyclassified asACvolt-
age controllers, matrix converters, and cycloconverters. Fig. 15.6
shows various topologies of multiphase AC-AC converters. AC
voltage regulators are further classified as phase-controlled con-
verters and fully controlled voltage converters.
Three-phase cycloconverters are of several types. For example,
there are the 3-pulse cycloconverters, 6-pulse cycloconverters,
and 12-pulse cycloconverters. Typically, the three-pulse con-
verter is built with the three single, and the six-pulse converter
is generally the combination of two three-pulse converters and
Multiphase DC-DC
converters
Multiphase
buck converter
Multiphase
boost converter
Multiphase Buck
boost converter
Unidirectional
converter
Bidirectional
converter
Unidirectional
converter
Bidirectional
converter
Unidirectional
converter
Bidirectional
converter
FIG. 15.3 Multiphase DC-DC converter classification.
5-phase
motor
Cell-1
AC/DC
converter
1-phase AC 5-phase AC
van
ven
Cell-2
AC/DC
converter
FIG. 15.5 Simplified five-phase drive.
Multiphase DC-AC
converters
Two level
5-Phase
Multilevel
Flying
capacitor
3-Phase n-Phase
6-Phase
Cascaded
H-Bridge
Diode
clamped
FIG. 15.4 Multiphase DC-AC converter classifications.
462 A. Iqbal et al.
7. so on. The 12-pulse converter is obtained by connecting two six-
pulse configurations in series and appropriate transformer con-
nections for the required phase shifted. Multiphase AC-AC
converter classification is shown in Fig. 15.6. By using the knowl-
edge of constructing a DC-modulated single-stage AC/AC
converter, a multistage AC/AC converter can be easily obtained.
Examples with complex structures are Luo converter, superlift
Luo converter, and multistage cascaded boost converter. Using
the same technique, one can construct DC-modulated multi-
phase AC/AC converters where they are classified as multiphase
AC/AC buck, boost, and buck-boost converter.
Cycloconverters are broadly classified as naturally commu-
tated and forced commutated. The later one is also known as
matrix converter. Multiphase matrix converters are in study
and are being studied in detail [4]. Fig. 15.7 shows some of
the possible configurations of frequency changers. The one
Multiphase AC-AC
converters
AC-AC voltage
regulator converters
Multiphase
phase controlled
AC voltage converter
Fully controlled
multiphase AC
voltage controller
Cycloconverters
With DC
energy storage
Without DC
energy storage
Hybrid
3-phase 3-pulse
converter
3-phase 6-pulse qud
converters
Matrix
converters
DC modulated multiphase
AC to AC converter
Buck converter
Boost
converter
Buck boost
converter
FIG. 15.6 Multiphase AC-AC converter classification.
Multiphase frequency
converters
With DC-link
VSR-VSI CSR-CSI
Without DC-link
(MPMC)
Direct
(DMMC)
Indirect
(IMMC)
Sparse MC
(SMC)
Ultra sparse MC
(USMC)
Multilevel
DMMC
Impedance-source MPMC
Possible topologies for
research
FIG. 15.7 Multiphase frequency changers. VSR, voltage source rectifier; VSI, voltage source inverter; CSR, current source rectifier; CSI, current source
inverter; MPMC, multiphase matrix converter; DMMC, direct multiphase matrix converter; IMMC, indirect multiphase matrix converter; SMC, sparse
matrix converter; USMC, ultra sparse matrix converter.
463
15 Multiphase Converters
8. with a DC link is also commonly known as back-to-back (B2B)
topology. Although B2B converter does the AC-AC conversion,
it is sort of a paradigm to classify the topologies without the
DC link under AC-AC converters. Also, the figure shows
the possibility of research in the field of multiphase matrix
converters.
15.3 Multiphase Multipulse AC-DC
Converters
Solid-state AC-DC converters are widely used in a number
of applications such as adjustable-speed drives (ASDs),
high-voltage DC (HVDC) transmission, and electrochemical
processes such as electroplating, telecommunication power sup-
plies, battery charging, uninterruptible power supplies (UPS),
high-capacity magnet power supplies, high-power induction
heating equipment, aircraft converter systems, plasma power
supplies, and converters for renewable energy conversion sys-
tems. These converters, which are also known as rectifiers,
are generally fed from three-phase AC supply in power rating
above few kilowatts. They exhibit the problems of power quality
in terms of injected harmonics, resulting in poor power factor,
AC voltage distortion, and rippled DC outputs. Because of these
problems in AC-DC conversion, several standards and guide-
lines are laid down, which are to be referred by designers, man-
ufacturers, and users. Therefore, various methods are used to
mitigate these problems in AC-DC converters. Normally, filters
are recommended in already existing installations, which may
be passive, active, or hybrid types depending upon rating and
economic considerations. These filters have been developed
from small to large power ratings to reduce the power quality
problems of AC-DC converters. However, in some cases, the
ratings of these filters are close to the converter rating, which
not only increases the cost but also increases the losses and com-
ponent count, resulting in reduced reliability of the system.
However, in future installations, it is preferred to modify the
converter structure at design stage either using active or passive
(magnetic) wave shaping of input currents or using multipulse
AC-DC converters by using multiphase system or different con-
nections of standard three-phase six-pulse AC-DC converters.
At higher power level, generally, multiphase system is preferred.
It reduces the ripples in the line current and load voltages dras-
tically, and thus, EMI reduces, and the harmonic filter require-
ments also become very nominal.
15.3.1 Five Phase Uncontrolled Full Wave Bridge
Rectifier
The circuit diagram of a simplified five-phase (ten pulses)
uncontrolled rectifier consisting of 10 diodes (D1–D10) is
shown in Fig. 15.8, where van, vbn, vcn, vdn, and ven are the supply
phase voltages having peak value of Vm given by Eq (15.1):
van ¼ Vm sin ωt
ð Þ
vbn ¼ Vm sin ωt 2π=5
ð Þ
vcn ¼ Vm sin ωt 4π=5
ð Þ
vdn ¼ Vm sin ωt 6π=5
ð Þ
van ¼ Vm sin ωt 8π=5
ð Þ
(15.1)
The diodes are assumed ideal and are numbered according
to their conduction sequence 1,2- ,3- 3,4- 4,5- 5,6- 6,7- 7,8-
8,9- 9,1.
The line voltages for adjacent phases will be different from
that of nonadjacent phases. The line voltages for adjacent
and nonadjacent phases can be obtained from the respective
phasor diagrams shown in Figs. 15.9 and 15.10, respectively,
as follows:
For adjacent phases,
vab ¼ van vbn
vab ¼ Vm sin ωt
ð ÞVm sin ωt 2π=5
ð Þ
vab ¼ 2Vm sin π=5
ð Þ cos ωt π=5
ð Þ
∵sin α sin β ¼ 2 cos
α + β
2
sin
αβ
2
vab ¼ 1:1755Vm sin ωt + 3π=10
ð Þ
(15.2)
D1 D3 D5 D7 D9
D6 D8 D10 D2 D4
ven
n
IDC
p
q
ia
ib
ic
id
ie
ia
wt
L
o
a
d
72
degrees
vdn
vcn
vbn
van
van
vbn
vcn
vdn
ven
FIG. 15.8 Five-phase full-wave uncontrolled rectifier circuit.
van
vbn
vcn
vdn
ven
–vbn
72 degrees
54 degrees
vab
FIG. 15.9 Phasor diagram of the line voltages of adjacent phases.
464 A. Iqbal et al.
9. For nonadjacent phases,
vad ¼ van vdn
¼ Vm sin ωt
ð ÞVm sin ωt 6π=5
ð Þ
¼ 2Vm sin 3π=5
ð Þ cos ωt 6π=10
ð Þ
vad ¼ 1:9021Vm sin ωt π=10
ð Þ
(15.3)
Fig. 15.11A shows the waveforms of the maximum and mini-
mum value of phase voltage in different intervals. The maxi-
mum phase voltage Vpn and minimum phase voltage Vqn
described by Eq (15.4) will appear at the output terminals p
and q. Both the diodes in the same leg never conduct simulta-
neously, which avoids direct short circuit in the leg. In the
upper leg, the diodes (odd numbered) having its anode con-
nected with phase voltage of highest value among phases will
conduct. Similarly, in the bottom leg, the diodes (even num-
bered) having its cathode connected with lowest phase voltage
will conduct at any instant of time:
Vpn ¼ max van, vbn, vcn, vdn, ven
ð Þ
Vqn ¼ min van, vbn, vcn, vdn, ven
ð Þ
(15.4)
The output-voltage waveform shown in Fig. 15.11B is a
10-pulse waveform appearing across the load. For a purely
resistive load, the waveform of the line current ia shown in
Fig. 15.11C has two humps per half cycle of the supply fre-
quency. The other four line currents, ib, ic, id, and ie, have
the same waveform as ia but lag from ia by 2π/5, 4π/5, 6π/5,
and 8π/5 radians, respectively. The average and rms value of
output voltage at load can be calculated as
VDC ¼
1
2π=10
ð
7π
10
π
2
1:902Vm sin ωt π=10
ð Þd ωt
ð Þ
VDC ¼ 1:87087Vm
(15.5)
Vrms ¼
ffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi
1
2π=10
ð
7π
10
π
2
1:902Vm sin ωt π=10
ð Þ
½ 2
d ωt
ð Þ
v
u
u
u
u
t
Vrms ¼ 1:87107Vm
(15.6)
For a resistive load, the harmonics of the output voltage can be
found by using Fourier series analysis. To find the Fourier coef-
ficients, we integrate vbe from π/10 to +π/10. Considering the
van
vbn
vcn
vdn
ven
−vdn
18 degrees
vad
72
degrees
FIG. 15.10 Phasor diagram for the addition of nonadjacent phases.
−0.5
0
0.5
+Vm
D9
D10
van vbn vcn vdn
ven
ven
veb vec vac vad vbd vbe vce vca vda vdb veb
−ncn
D2
−ndn
D4
−nen
D6
−nan
D8
−nbn
wt
wt
wt
wt
−Vm
0
Vm
0.5Vm
1.5Vm
1.9Vm
v
vo
VDC
ia
iD1
0
0
D1 D3 D5 D7 D9
(A)
(B)
(C)
(D)
π/5 2π/5 3π/5 4π/5 6π/5 7π/5 8π/5 9π/5 2π
π
p/10 5p/10
3p/10 7p/10 11p/10 15p/10 2p
3p/10 7p/10 11p/10 15p/10 2p
13p/10 17p/10 2p
9p/10
FIG. 15.11 (A) Phase voltages w.r.t p and q points, (B) output voltage
across the load, (C) phase “a” current, and (D) diode current.
465
15 Multiphase Converters
10. half-wave symmetry, the Fourier coefficients will be calculated
as follows:
bn ¼ 0 (15.7)
an ¼
1
π=10
ð
π
10
π
10
1:9021Vm cos ωt
ð Þ cos nωt
ð Þd ωt
ð Þ
¼ 6:067Vm
n + 1
ð Þ sin n1
ð Þ
π
10
h i
+ n1
ð Þ sin n + 1
ð Þ
π
10
h i
n2 1
ð Þ
8
:
9
=
;
an ¼
12:134Vm
n2 1
ð Þ
n sin
nπ
10
cos
π
10
cos
nπ
10
sin
π
10
n o
(15.8)
If the frequency of the source voltage is f, the output voltage has
harmonics at 10f, 20f, 30f …etc. Eq. (15.8) is simplified as
an ¼
12:134Vm
n2 1
ð Þ
cos
nπ
10
sin
π
10
n o
an ¼
3:75Vm
n2 1
ð Þ
cos
nπ
10
(15.9)
The DC component is found by putting n¼0 in Eq. (15.9), and
its value is
VDC ¼
a0
2
¼ 1:87Vm (15.10)
This is the same value as calculated in Eq. (15.5). The Fourier
series of the load voltage can be written as
vL t
ð Þ ¼
a0
2
+
X
∞
n¼10,20,⋯
an cos nωt
ð Þ (15.11)
After substituting the values of the coefficients, we obtain
vL t
ð Þ ¼ 1:87Vm 1
X
∞
n¼10,20,⋯
2
n2 1
ð Þ
cos
nπ
10
cos nωt
!
(15.12)
vL t
ð Þ ¼ 1:87Vm 1 +
2
99
cos 10ωt
2
399
cos 20ωt + ⋯
(15.13)
Fig. 15.12 shows the load voltage harmonics profile. Since each
diode conducts one fifth of the time, the average diode current
is given by Eq. (15.14).
ID,avg: ¼
1
2π
ð
7π
10
3π
10
IDCd ωt
ð Þ
2
6
4
3
7
5 ¼ 0:2IDC (15.14)
Eq. (15.14) indicates that a five-phase rectifier will have
switches with lower ratings as compared with the three-phase
counterpart, provided that both are feeding the same load as
average value of switch current in three-phase system is
33.33% and in this case it is 20% [9,10]. The input phase current
can be expressed as
is ¼
X
∞
n¼1,3,5....
4IDC
nπ
sin
nπ
5
sin nωt
ð Þ (15.15)
The fundamental component of input current is
is1 ¼ 0:7484IDC sin ωt
ð Þ (15.16)
The rms value of the fundamental component of input current is
Is ¼
ffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi
1
π
ð
7π
10
3π
10
I2
DCdωt
v
u
u
u
u
t ¼
ffiffiffi
2
5
r
IDC (15.17)
PROBLEM 15.1 A five-phase bridge rectifier delivers
60 A current at a voltage of 317.5 V to a purely resistive
load. If the frequency of the source is 60 Hz, determine
the following:
(a) Efficiency of rectification
(b) Form factor
(c) Ripple factor
(d) Peak inverse voltage (PIV) of each diode
(e) Peak current through a diode
10 20 30 40 50 60 70
0
Harmonics order
Harmonics
magnitude
2.02%
0.5%
0.22%
0.13%
100%
0.08% 0.05% 0.04%
1
2
1.5
0.5
FIG. 15.12 Harmonics profile of output voltage.
466 A. Iqbal et al.
11. SOLUTION Since VDC ¼1.87087Vm and Vrms ¼
1.87101Vm and also IDC ¼VDC/R and Irms ¼Vrms/R,
(a) Efficiency of rectification η ¼
Pac
PDC
¼
Vrms
2
R
VDC
2
R
¼
1:87107
ð Þ2
1:87087
ð Þ2 ¼ 99:97%
(b) Form factor FF ¼
Vrms
VDC
¼
1:87107
187087
¼ 100:011%
(c) Ripple factor RF ¼
ffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi
FF2 1
p
¼
ffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi
1:00011
ð Þ2
1
q
¼
1:483%
(d) Peak inverse voltage of each diode¼1.902Vm
Also, since VDC ¼1.87087 Vm and peak value of
phase voltage, Vm ¼
VDC
1:87087
¼
317:5
1:87087
¼ 169:70V
Hence, PIV ¼ 1:902169:70 ¼ 322:78V
(e) The average DC current through each diode is
IDC Diode
ð Þ ¼
IDC
5
¼
60
5
¼ 12A
Also, IDC Diode
ð Þ ¼ 4
π
ð
π
10
0
Im cos ωtdωt
IDC ¼ 0:19673Im
Im ¼
IDC
0:19673
¼
12
0:19673
¼ 61A
15.3.2 Five-Phase Controlled Full Wave Bridge
Rectifier
Whenever a diode is in forward-biased condition, it conducts,
but a thyristor (or controlled switch) requires a triggering signal
for its conduction. If all the diodes of a 10-pulse full-wave
uncontrolled converter are replaced by controlled switches (thy-
ristors), it becomes a controlled converter. Fig. 15.13 shows the
basic power circuit of a fully controlled 10-pulse 5-phase
AC-DC converter. In this case, the thyristors are switched at
an interval of 36 degrees sequentially as shown in Table 15.1.
When T1 and T2 are conducting van and vbn voltages with
respect to neutral appear at the load, that is, vad ¼van vdn,
which is the line voltage VL (vad ¼ 1:9021Vm sin ωt
ð π=10Þ).
At ωt¼π/2+α, T1 is commutated, as on this instant of time
vbn van, and the load current is transferred from T1 to T3.
There are 10 voltage pulses, and the instantaneous output volt-
age may become negative for an RL load, but the Vdc will always
have positive value, except for an active (RLE) load. It should be
noted that the line voltage corresponding to the nonadjacent
phase voltages is only appearing across the load. AC voltages
applied to the rectifier is given by Eq. (15.1).
The delay angle reference is taken from the point the thyris-
tor would begin to conduct if it were a diode. Thus, the delay
angle is an interval from the thyristor being forward-biased and
till the gate signal is applied. The corresponding waveforms are
shown in Fig. 15.14A–H [9,10]. Since each voltage pulse corre-
sponds to the line voltage and it appears for 1/10th period of the
cycle 2π/10, the average output voltage corresponding to vad
shown in Table (15.1) is given by
VDC ¼
1
2π
10
ð
7π
10 + α
5π
10 + α
1:902Vm sin ωt π=10
ð Þd ωt
ð Þ
VDC ¼
51:902Vm
π
cos ωt π=10
ð Þ
½
7π
10 + α
5π
10 + α
VDC ¼ 1:87Vm cos α
(15.18)
T1 T3 T5 T7 T9
T6 T8 T10 T2 T4
van ia
ia
ib
ic
id
ie
vbn
vcn
vdn
ven
n
IDC
p
q
wt
L
o
a
d
van
vbn
vcn
vdn
ven
72
degrees
FIG. 15.13 Five-phase full-wave bridge rectifier basic circuit.
TABLE 15.1 Thyristor firing instants and output voltage across the load
Time interval Thyristor fired Conducting thyristor Output voltages across load
[π/10+α, 3π/10+α] T10 T9 and T10 vo ¼ vec ¼ 1:902Vm sin ωt + 3π=10
ð Þ
[3π/10+α, 5π/10+α] T1 T10 and T1 vo ¼ vac ¼ 1:902Vm sin ωt + π=10
ð Þ
[5π/10+α, 7π/10+α] T2 T1 and T2 vo ¼ vad ¼ 1:902Vm sin ωt π=10
ð Þ
[7π/10+α, 9π/10+α] T3 T2 and T3 vo ¼ vbd ¼ 1:902Vm sin ωt 3π=10
ð Þ
[9π/10+α, 1π/10+α] T4 T3 and T4 vo ¼ vbe ¼ 1:902Vm sin ωt π=2
ð Þ
[11π/10+α, 13π/10+α] T5 T4 and T5 vo ¼ vce ¼ 1:902Vm sin ωt 7π=10
ð Þ
[13π/10+α, 15π/10+α] T6 T5 and T6 vo ¼ vca ¼ 1:902Vm sin ωt 9π=10
ð Þ
[15π/10+α, 17π/10+α] T7 T6 and T7 vo ¼ vda ¼ 1:902Vm sin ωt + 9π=10
ð Þ
[17π/10+α, 19π/10+α] T8 T7 and T8 vo ¼ vdb ¼ 1:902Vm sin ωt + 7π=10
ð Þ
[19π/10+α, 21π/10+α] T9 T8 and T9 vo ¼ veb ¼ 1:902Vm sin ωt + 5π=10
ð Þ
467
15 Multiphase Converters
12. The rms output voltage is
Vrms ¼
ffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi
1
2π=10
ð
7π
10 + α
5π
10 + α
1:902Vm sin ωt π=10
ð Þ
ð Þ2
v
u
u
u
u
u
t
Vrms ¼
ffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi
51:9022
V2
m
π
ð
7π
10 + α
5π
10 + α
1 cos 2 ωt π
10
2
v
u
u
u
u
u
t
d ωt
ð Þ
Vrms ¼
ffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi
51:9022
V2
m
2π
ωt
1
2
sin 2 ωt
π
10
7π
10 + α
5π
10 + α
v
u
u
t
Vrms ¼ 1:902Vm
ffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi
1
2
+
5
2π
sin π=5
ð Þ cos 2α
r
(15.19)
It is evident from Fig. 15.14D that the instantaneous output
voltage is continuous for απ/5; therefore, for any passive
load, the load current will be continuous. For 3π/10απ/5,
the continuity of load current depends on the phase angle
of load (φ) and discontinuous for purely resistive load
(φ¼0). For α3π/10, the load current will be always discon-
tinuous for the passive load (Vdc 0), whereas for active load
(RLE), there will be fourth-quadrant operation (Vdc 0 and
Idc 0).
Fig. 15.14E shows the input phase current, which is a quasis-
quare wave. Since the instantaneous value of load current is
assumed to be constant, so the phase current will be +IDC in
the interval (3π/10+α and 7π/10+α) and IDC in the interval
(13π/10+α and 17π/10+α). Also, each phase currents will be
displaced from each other by 2π/5, irrespective of thyristor
firing angles. The input phase current ia can be expressed in
Fourier series as
ia ¼ IDC +
X
∞
n¼1,2,3,…
an cos nωt + bn sin nωt
ð Þ
ia ¼ IDC +
X
∞
n¼1,2,3,…
ffiffiffi
2
p
In sin nωt + φn
ð Þ
(15.20)
where In is the rms value of nth harmonic component of the
input current and is given by
In ¼
1
ffiffiffi
2
p a2
n + b2
n
1
2 (15.21)
The φn is the nth harmonic phase shift and is given by
φn ¼ tan1 an
bn
(15.22)
Also, due to the symmetry of waveform,
IDC ¼
1
2π
ð
2π
0
i ωt
ð Þdωt ¼ 0 (15.23)
0
ve
a
va
vpn 72 degrees
vb vc vd
-vb -vc -vd -ve -va -vb
0
Vm
0.5Vm
Vdb Veb Vec Vac Vad Vbd Vbe Vce Vca Vda Vdb
p/10 3p/10
−IDC
T7,T8 T8,T9 T9,T10 T10,T1 T1,T2 T2,T3 T3,T4 T4,T5 T5,T6 T6,T7 T7,T8
1.5Vm
1.902Vm
g1 g3 g5 g7
g9
g2 g4 g6 g8
g10
IDC
iL
iT1
ia
vT1
vL
wt
wt
wt
wt
wt
wt
wt
wt
vqn
Vm
−Vm
v
0.5Vm
(A)
(B)
(C)
(D)
(E)
(F)
(G)
(H)
+IDC
+IDC
5p/10 7p/10 p9/10 11p/10 13p/10 15p/10 17p/10 19p/10 21p/10
p/5 3p/5 p 7p/5 9p/5 2p
FIG. 15.14 (A) Supply voltage with positive and negative waveforms,
(B) gate pulses for firing upper-leg switches, (C) gate pulses for firing
lower-leg switches, (D) output-voltage waveform, (E) supply current of
phase a, (F) switch 1 current, (G) load current, and (H) voltage across
switch 1.
468 A. Iqbal et al.
13. an ¼
1
π
ð
2π
0
ia cosnωt dωt
an ¼
1
π
ð
7π
10 + α
3π
10 + α
IDC cosnωt dωt
ð
17π
10 + α
13π
10 + α
IDC cosnωt dωt
2
6
6
4
3
7
7
5
an ¼
4IDC
nπ
sin
nπ
5
sinnα, n ¼ 1,3,5,… (15.24)
Similarly,
bn ¼
1
π
ð
2π
0
ia sin nωtdωt
bn ¼
1
π
ð
7π
10 + α
3π
10 + α
IDC sin nωtdωt
ð
17π
10 + α
13π
10 + α
IDC sin nωtdωt
2
6
6
4
3
7
7
5
bn ¼
4IDC
nπ
sin
nπ
5
cos nα, n ¼ 1,3,5,… (15.25)
Therefore, the rms value of nth harmonics current will be
given by
In ¼
1
ffiffiffi
2
p a2
n + b2
n
1
2 ¼
2
ffiffiffi
2
p
nπ
IDC sin
nπ
5
(15.26)
and
φn ¼ tan1 an
bn
¼ nα (15.27)
n¼1 will give the rms value of fundamental component of the
input current:
I1 ¼
2
ffiffiffi
2
p
π
IDC sin
π
5
¼ 0:529IDC (15.28)
Hence, the input current can be given by
is ¼
X
∞
n¼1,3,5,…
4IDC
nπ
sin
nπ
5
sin nωt nα
ð Þ (15.29)
The fundamental input current, (substituting, n¼1), is
is1 ¼
4IDC
π
sin
π
5
sin ωt α
ð Þ ¼ 0:7484IDC sin ωt α
ð Þ (15.30)
The rms value of the input current can be calculated as
Irms ¼
1
2π
ð
2π
0
i2
dωt
2
4
3
5
1
2
¼
2
2π
ð
7π
10 + α
3π
10 + α
I2
DCdωt
2
6
6
4
3
7
7
5
1
2
¼
ffiffiffi
2
5
r
IDC ¼ 0:6324IDC
(15.31)
The total harmonic distortion (THD) is given by
THD ¼
ffiffiffiffiffiffiffiffiffiffiffi
I2
I2
1
1
s
¼
ffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi
0:634IDC
ð Þ2
0:529IDC
ð Þ2 1
s
¼ 65:5% (15.32)
Displacement factor
DF ¼ cos φ1
ð Þ ¼ cos α
ð Þ ¼ cos α (15.33)
Power factor
PF ¼
cos α
ffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi
1 + THD2
p ¼
I1
I
cos α ¼
0:529IDC
0:634IDC
cos α ¼ 0:8365 cos α
(15.34)
The load current is constant as the load is considered highly
inductive; from Fig. 15.14F, it is clear that each switch operates
for 2π/5 period of time in one cycle; accordingly, the switch
average current can be calculated as
Isw_avg: ¼
1
2π
ð
7π
10 + α
3π
10 + α
IDCdωt
2
6
6
4
3
7
7
5 ¼ 0:2IDC (15.35)
When calculated, the switch current is only 20% of DC-link
current [10]. The harmonic factor (HFn) is defined as the nor-
malized harmonic current of the supply with respect to the fun-
damental component (In/I1) and is calculated using Eq. (6.36):
HFn ¼
ffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi
In
I
2
1
s
(15.36)
PROBLEM 15.2 A five-phase full-wave bridge-controlled
rectifier has an AC input of 120 V rms at 60 Hz and
100 Ω load resistor. The delay angle is α¼π/12 radians.
Determine the following:
(a) Average current in the load
(b) Power absorbed by the load
469
15 Multiphase Converters
14. (c) Efficiency of the rectifier
(d) The expression for the input current
(e) THD
(f ) Power factor of the rectifier
(g) Form factor and ripple factor
SOLUTION
(a) Average load voltage VDC ¼ 1:87Vm cos α ¼ 1:87
ffiffiffi
2
p
120 cos π=12
ð Þ ¼ 306:53V
Average load current IDC ¼
VDC
R
¼
306:53
100
¼ 3:06A
(b) Power absorbed by the load PDC ¼ VDC IDC ¼
306:533:06 ¼ 938W
(c) The rms value of the output voltage Vrms ¼
1:902Vm
ffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi
1
2 + 5
2π sin π
5
cos 2α
q
Vrms ¼ 1:902120
ffiffiffi
2
p
ffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi
1
2
+
5
2π
sin
π
5
cos 2
π
12
r
Vrms ¼ 307:08V
and Irms ¼
Vrms
R
¼
307:08
100
¼ 3:071A
Therefore, efficiency η ¼
PDC
Pac
¼
VDCIDC
VrmsIrms
¼
306:533:06
307:083:071
¼ 99:46%
(d) The expression for the input current is ¼
X
∞
n¼1,3,5,…
4IDC
nπ
sin
nπ
5
sin nωt nα
ð Þ
is ¼
X
∞
n¼1,3,5,…
3:9
n
sin
nπ
5
sin nωt nπ=12
ð Þ
(e) The rms value of the input current I ¼
ffiffi
2
5
q
IDC ¼
ffiffi
2
5
q
3:06 ¼ 1:935A
The rms value of fundamental component of the
input current
I1 ¼
2
ffiffiffi
2
p
π
sin
π
5
IDC ¼ 0:5293:06 ¼ 1:6187
THD ¼
ffiffiffiffiffiffiffiffiffiffiffi
I2
I2
1
1
s
¼
ffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi
1:935
ð Þ2
1:6187
ð Þ2 1
s
¼ 65:5%
(f ) The power factor PF ¼
cos α
ffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi
1 + THD2
p ¼
cos π=15
ð Þ
ffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi
1 + 0:655
ð Þ2
q ¼
0:818
(g) Form factor FF ¼
Vrms
VDC
¼
307:08
306:53
¼ 1:0018 ¼ 100:18%
Ripple factor RF ¼
ffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi
FF2 1
p
¼
ffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi
1:0018
ð Þ2
1
q
¼
0:06 ¼ 6%
15.3.3 Multipulse Rectifiers
The multipulse uncontrolled rectifiers are suitable for VSI-fed
drives, while the controlled rectifiers are employed for CSI
drives. As the number of pulses per cycle increases, the output
waveform gets improved. There are identical multipulse recti-
fiers connected in either parallel, series, or separate modes to
achieve higher pulses in the output. Fig. 15.15 shows general
layout of 12-, 18-, and 24-pulse rectifier circuits [29,30]. If
we employ 10-pulse rectifiers, then we can obtain 20, 30, and
40 pulses in the output.
Six pulse
rectifier
Six pulse
rectifier
Phase shifting
transformer
VDC1
+
−
VDC2
+
−
VDC1
+
−
VDC2
+
−
VDC3
+
−
VDC1
+
−
VDC2
+
−
VDC3
+
−
VDC4
+
−
FIG. 15.15 Multipulse uncontrolled/controlled rectifier’s arrangement.
470 A. Iqbal et al.
15. 15.3.3.1 12-Pulse Series Type Controlled Rectifier
Two six-pulse controlled rectifiers are powered by a phase-
shifting transformer with two secondary windings in delta
and star connections. Therefore, the phase angle between both
secondary windings shifts 30 degrees each. In this case with
12 pulses per cycle, the quality of output-voltage waveform
would definitely be improved with low ripple content [29].
Fig. 15.15 shows circuit configuration of a 12-pulse series-
type controlled rectifier. A three-phase transformer with two
secondary and one delta-connected primary feeds the two
identical six-pulse controlled rectifiers. The upper three-phase
bridge is fed from Y-connected secondary winding while lower
with Δ-connected secondary winding. Therefore, this arrange-
ment will result in the phase angle shifts between both second-
ary windings by 30 degrees. The outputs of the two six-pulse
rectifiers are connected in series, and the conduction period
of the line current for each converter is 120 degrees.
Consider an idealized 12-pulse rectifier where the line induc-
tance Ls and the total leakage inductance Llk of the transformer
are assumed to be zero and the magnitude of the current is con-
stant (ripple-free) [29]. In practical case, the ripple in the DC
current will be relatively low due to the series connection of
the two six-pulse rectifiers, where the leakage inductances of
the secondary windings can be considered in series.
For the purpose of eliminating the dominate lower-order har-
monics in the line current ia, the line-to-line voltage va1b1 of the
Y-connected secondary winding (N2 turns) is in phase with the
primary winding (N1 turns) voltage vab, while the Δ-connected
secondary winding (N3 turns) voltage va2b2 leads vab by [29]:
δ ¼ ∠va2b2
∠vab ¼ 30 degrees (15.37)
For the sake of simplicity, let N1 ¼ N,N2 ¼ N=2 and
N3 ¼
ffiffiffi
3
p
=2N (i.e., N1-N2-N3 ¼1:0.5:0.866).
Therefore, the rms line-to-line voltage of each secondary
winding will become
Va1b1 ¼ Va2b2 ¼ Vab=2 (15.38)
Since the two rectifiers are series-connected, net output, or
load, voltage Vdc ¼Vdc1 +Vdc2 ; since the waveforms of Vdc1
and Vdc2 are phase shifted from each other by 30 degrees ,
therefore, the waveform of output voltage Vdc consists of
12 pulses per cycle of supply voltage. The current waveforms
are illustrated in Fig. 15.16, where ia1 and ic2a2 are the phase
currents of secondary Y and Δ windings, respectively, and i
0
a1
and i
0
c2a2 are the currents referred from secondary side to the
primary side. The waveforms of reflected current to primary
side of secondary Y-connected winding i
0
a1 will be identical
to that of ia1 except that the magnitude is changed in ratio of
the number of turns of the two windings. However, when ia2
is referred to the primary side, the reflected waveform does
not keep the same waveform and magnitude. This is due to
phase displacements of the harmonic current when they are
referred from Δ-Y windings. This phase displacement is advan-
tageous as it will lead to the cancelation of low-order predom-
inant fifth and seventh harmonics from the currents of
transformer primary winding and does not appear in the line
current, which is given by Eq. (15.39):
ia ¼ i’
a1 + i’
a2 (15.39)
The secondary (Y-connected) line current ia1 can be expressed
by Eq. (15.40):
L
o
a
d
IDC
c
vcn
n
N1
vab
va2b2
ia2
ic2a2
ib2c2
ia = i′a1+i′a2c2
d= 30 degrees
d = 0
ia2b2
ib
a2
b2
c2
a1
b1
c1
ia1
ib1
ic1
b
vbn
a
van
ic
N2
N3
ib2
ic2
FIG. 15.16 Twelve-pulse series-type controlled rectifier connection circuit.
471
15 Multiphase Converters
16. ia1 ¼
2
ffiffiffi
3
p
π
Idc
sin ωt
1
5
sin 5ωt
1
7
sin 7ωt +
1
11
sin 11ωt
+
1
13
sin 13ωt
1
17
sin 17ωt
1
19
sin 19ωt + …
2
6
6
4
3
7
7
5
(15.40)
Since the waveform of current ia1 is of half-wave symmetry, it
does not contain any even-order harmonics. Current ia does
not contain any triple harmonics either due to the consider-
ation of balanced three-phase system. The line current in
Δ-connected secondary winding such as ia2 leads ia1 by
30 degrees, and the Fourier expression of current ia2 is given
by Eq. (15.41):
ia2 ¼
2
ffiffiffi
3
p
π
Idc
sin ωt + 30degrees
ð Þ
1
5
sin 5 ωt + 30degrees
ð Þ
1
7
sin 7 ωt + 30degrees
ð Þ
+
1
11
sin 11 ωt + 30degrees
ð Þ
+
1
13
sin 13 ωt + 30degrees
ð Þ
1
17
sin 17 ωt + 30degrees
ð Þ
1
19
sin 19 ωt + 30degrees
ð Þ + …
2
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
4
3
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
5
(15.41)
Similar equations for ib2 and ic2 can be obtained. The current
i0
a1, which is identical to ia1 in wave shape, can be expressed
in Fourier series by Eq. (15.42):
i’
a1 ¼
ffiffiffi
3
p
π
Idc sin ωt
1
5
sin 5ωt
1
7
sin 7ωt
+
1
11
sin 11ωt +
1
13
sin 13ωt…
(15.42)
The phase currents in the Δ-connected secondary windings
ia2b2, ib2c2, and ic2a2 can be obtained from its line currents using
the transformation given in Eq. (15.43):
ia2b2
ib2c2
ic2a2
2
6
6
4
3
7
7
5 ¼
1
3
1 1 0
0 1 1
1 0 1
2
6
6
4
3
7
7
5
ia2
ib2
ic2
2
6
6
4
3
7
7
5 (15.43)
The phase currents in the Δ-connected secondary winding
ia2b2, ib2c2, and ic2a2 have a stepped waveform, each step being
of 60 degrees in width whereas Id/3 and 2Id/3 the heights. The
expression for phase current in the Δ-connected secondary
winding can be written as Eq. (15.44).
ic2a2 ¼
2
π
ffiffiffi
3
p Idc
sin ωt + 30degrees
ð Þ
1
5
sin 5 ωt + 30degrees
ð Þ
1
7
sin 7 ωt + 30degrees
ð Þ
+
1
11
sin 11 ωt + 30degrees
ð Þ + ⋯
sin ωt + 150degrees
ð Þ
+
1
5
sin 5 ωt + 150degrees
ð Þ
+
1
7
sin 7 ωt + 150degrees
ð Þ
1
11
sin 11 ωt + 150degrees
ð Þ ⋯
2
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
4
3
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
5
(15.44)
On simplification of Eq. (15.44), we have
ic2a2 ¼
2
π
Idc
sin ωt +
1
5
sin 5ωt +
1
7
sin 7ωt +
1
11
sin 11ωt
+
1
17
sin 17ωt +
1
19
sin 19ωt + ⋯
2
6
4
3
7
5
(15.45)
Similarly, the expressions for the currents ia2b2 and ib2c2 can be
obtained. The corresponding reflected current to the primary
side can be obtained from Eq. (15.45); by multiplying with turn
ratio (N3 : N1 ¼
ffiffiffi
3
p
: 2), we can obtain Eq. (15.46) [31]:
i’
c2a2 ¼
ffiffiffi
3
p
π
Idc
sin ωt +
1
5
sin 5ωt +
1
7
sin 7ωt +
1
11
sin 11ωt
+
1
13
sin 13ωt +
1
17
sin 17ωt +
1
19
sin 19ωt
+
1
23
sin 23ωt +
1
25
sin 25ωt + ⋯
2
6
6
6
6
6
4
3
7
7
7
7
7
5
(15.46)
Therefore, the line current ia ¼ i’
a1 + i’
c2a2 can be written as given
in Eq. (15.47):
ia ¼
2
ffiffiffi
3
p
π
Idc
sin ωt +
1
11
sin 11ωt +
1
13
sin 13ωt
+
1
23
sin 23ωt +
1
25
sin 25ωt + ⋯
2
6
4
3
7
5 (15.47)
Different current waveforms are shown in Fig. 15.17. It is evi-
dent from Eq. (15.47) that the two dominant harmonics, 5th
and 7th, are absent along with 17th and 19th, which improves
the THD of this type of converter configuration drastically.
15.3.3.2 Pulse Parallel-Type Controlled Rectifier
In this case, the outputs of the two six-pulse rectifiers are con-
nected in parallel. Fig. 15.18 shows circuit configuration of a
12-pulse parallel-type controlled rectifier. The circuit in the fig-
ure simply uses an isolation transformer with a Δ-connected
primary, a Y-connected secondary, and a second Δ-connected
secondary to obtain 30 degrees (electrical degrees) phase shift.
Since the instantaneous outputs of the two rectifiers are not
472 A. Iqbal et al.
17. equal, an interphase reactor is necessary to support the differ-
ence in instantaneous rectifier output voltages and permit each
rectifier to operate independently [29]. The line current in pri-
mary winding of the transformer is the sum of reflected cur-
rents from the two secondary windings, and it becomes
stepped due to 30 degrees phase shift in two secondary currents
as discussed in Section 15.3.3.1. Therefore, the harmonics and
requirement of filter circuit parameters are reduced. Theoreti-
cally, input current harmonics for rectifier circuit is a function
of pulse number and can be expressed as
H ¼ Np 1
(15.48)
where N¼1, 2, 3… and p is pulse number.
For example, in a three-phase six-pulse rectifier, the input
current will have harmonic components at 5, 7, 11, 13, 17,
19, 23, 25, 29, 31, etc. multiples of the fundamental frequency.
For the 12-pulse system shown in Fig. 15.16, the input current
will have theoretical harmonic components at 11, 13, 23, 25, 35,
37, etc. multiples of the fundamental frequency as derived and
discussed in Section 15.3.3.1. Since the magnitude of each har-
monic is proportional to the reciprocal of the harmonic order,
the 12-pulse system naturally has a lower harmonic distortion
in input current.
The problem with the parallel connection of the rectifiers is
that thetworectifiersmustshare exactlyequalcurrenttoachieve
the desired reduction in harmonics. This would be achieved if
output voltages of both secondary windings matches exactly.
Because of the differences in the transformer secondary imped-
ances and open-circuit output voltages, this can be practically
accomplished for a given fixed load (typically rated load), but
not for loads varying over a range. This is the main problem
of the parallel 12-pulse configuration connection. Whereas in
the case of series connection of two rectifiers, the problems asso-
ciated with current sharing are avoided, and an interphase reac-
tor is not required. Parallel connections are normally preferred
for applications where high current ratings rather than har-
monics are the issue [32]. Generally, series connection of recti-
fiers is much simpler to implement than the parallel connection.
L
o
a
d
N1
a2
b2
c2
a1
b1
c1
N2
N3
FIG. 15.18 Twelve-pulse parallel-type controlled rectifier connection
circuit.
p/2 p 3p/2 2p
wt
wt
wt
wt
wt
wt
i′c2a2
i′a1
ia
3
2IDC
2
IDC
3
2
IDC
2
IDC
3
2
IDC
3
2
IDC
3
IDC
3
IDC
3
1
2
1
IDC
7p/6
5p/6 11p/6 2p
p 5p/3
2p/3
p/2
p/3
p/6 4p/3 3p/2
ia1
0
ia2
ic2a2
IDC
IDC
(A)
(B)
(C)
(D)
(E)
(F)
FIG. 15.17 Current waveforms of the 12-pulse series-connected con-
trolled rectifier (Ls¼Llk¼0). (A) Output line/phase current in star-
connected secondary winding. (B) Output line current in delta-connected
secondary winding. (C) Output phase current in delta-connected second-
ary winding. (D) Delta-connected secondary winding phase current
reflected to primary side. (E) Star-connected secondary winding phase
current reflected to primary side. (F) Total current in the primary side.
473
15 Multiphase Converters
18. 15.3.4 Single-Way Multiphase Systems
Topologies
The structure of single-way, m-phase rectifier is shown in
Fig. 15.19. In single-way structures, only one diode conducts
for single stage, and the remaining diodes are blocked. Due
to this, single-way structures are more convenient while
increasing the number of phases. In an m-phase, the diodes
used in the rectifier circuits are divided into a number of groups
in star connection. Each group will have three diodes, that is,
for a six-diode rectifier, there will be two groups, and for a
12-diode rectifier, there will be four groups [31]. In a normal
connection, the star points will be connected together. But in
this circuit, each group will have its all secondary windings,
and instead of a direct connection, the star points will be con-
nected through an interphase transformer. The common neu-
tral point serves as the negative terminal of the DC output
circuit.
For single-way topologies, the number of output pulses is
equal to the number of phases, that is, p¼m, and the number
of diodes are equal to m. Each diode is conducting for 2π/m
electric radians. Fig. 15.19 shows few pulses of output-voltage
waveform for m-phase half-wave uncontrolled rectifier. In gen-
eral, for an m-phase system, the average and rms value of the
output voltage is expressed by Eqs. (15.49) and (15.50),
respectively:
VDC ¼
Vm
2π=m
ð
π
m
π
m
cos ωt d ωt
ð Þ¼
Vm sin
π
m
π=m
(15.49)
rms voltage Vrms ¼
ffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi
1
2π=m
ð
π
m
π
m
Vm cos ωt dωt
ð Þ2
v
u
u
u
u
t
Vrms ¼ Vm
ffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi
ffi
1
2
1 +
sin
2π
m
2π
m
2
6
6
4
3
7
7
5
v
u
u
u
u
u
t (15.50)
The form factor and ripple factors are expressed by Eqs. (15.51)
and (15.52), respectively. From these equations, it is evident
that if m ! ∞ ) FF ! 1 and RF ! 0,
FF ¼
Vrms
VDC
¼
ffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi
ffi
1
2
1 +
sin
2π
m
2π
m
2
6
6
4
3
7
7
5
v
u
u
u
u
u
t
sin
π
m
π
m
(15.51)
RF ¼
ffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi
1 FF
ð Þ2
q
(15.52)
which implies that by increasing the number of phases in a
multiphase, single-way rectifier, the output voltage is
improved, that is, it becomes smoother. By connecting to a con-
ventional three-phase mains distribution, it is possible to
increase the number of “phases” by using transformers with
m separated secondary coils. The secondary coils can be con-
nected in a large number of ways. Also, by increasing the num-
ber of phases (as stated before, in single-way topologies, m¼p),
the ripple frequency increases, and its amplitude decreases.
This fact simplifies the filter design to reduce the ripple in
the load [31,32]. The output waveform for m-phase half-wave
diode rectifier is shown in Fig. 15.20. For highly inductive load,
the output DC current may be considered as constant (IDC).
The diode average current, rms current, and form factor can
be obtained by Eqs. (15.53)–(15.55):
ID avg:
ð Þ ¼
IDC
m
(15.53)
ID rms
ð Þ ¼
IDC
ffiffiffiffi
m
p (15.54)
Kf ¼
ID rms
ð Þ
ID avg
ð Þ
¼
ffiffiffiffi
m
p
(15.55)
L
o
a
d
vs1
vs2
vs3
vsm
D3
D1
D2
Dm
VDC
IDC
FIG. 15.19 m-Phase, single-way rectifier.
2p/m
Vm
vs3
vs2
vs1
iL
FIG. 15.20 Output waveform for m-phase half-wave diode rectifier.
474 A. Iqbal et al.
19. The values for VDC and some of the parameters have been cal-
culated for m¼6, m¼12, and m¼24 and are reported in
Fig. 15.21. It is clear from the figure (A)–(C) that the frequency
of the ripple on the output is p times the mains frequency.
As can be seen, passing from 6 to 12 pulses, one gets a 3.5%
improvement in the rectified voltage, while passing from
12 to 24 pulses this improvement is less than 1%.
In practice, for single-way connections, the maximum num-
ber of pulses is normally limited to 12 because of the growing
complexity of the connections of the transformer’s secondary
windings. Higher number of pulses can be obtained by using
the combination of bridge structures. The best transformer uti-
lization factor (TUF) that can be achieved with a single-way
connection is 0.79, while with a bridge configuration it is pos-
sible to reach higher values, up to 0.955.
15.3.5 Six-Phase AC to DC Converters
Six-phase half-wave rectifiers generally have two configura-
tions, namely, six phase with a neutral line circuit and double
antistar with a balance-choke circuit.
15.3.5.1 Six-Phase Half Wave With a Neutral Line
Circuit
The power supply of a six-phase balanced voltage source
is given by Eq. (15.56), and the waveform is shown in
Fig. 15.22; in this case, each phase is shifted by 60 degrees:
van ¼ Vm sin ωt
vbn ¼ Vm sin ωt π=3
ð Þ
vcn ¼ Vm sin ωt 2π=3
ð Þ
vdn ¼ Vm sin ωt π
ð Þ
ven ¼ Vm sin ωt 4π=3
ð Þ
vbn ¼ Vm sin ωt 5π=3
ð Þ
(15.56)
The six-phase half-wave rectifiers are shown in Fig. 15.23. The
first circuit is called a Y-Y circuit, and the second circuit is
called a Δ/Y circuit. Each diode conducts for 60 degrees in a
cycle.
VDC ¼
1
π=3
ð
2π
3
π
3
Vm sin ωtdωt ¼
3Vm
π
(15.57)
Vrms ¼
ffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi
1
π=3
ð
2π
3
π
3
Vm sin ωt
ð Þ2
dωt
2
6
4
3
7
5
v
u
u
u
u
t ¼ Vm
ffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi
1
2
+
3
ffiffiffi
3
p
4π
s
(15.58)
FF ¼
Vrms
Vdc
¼ 1:0008 (15.59)
RF ¼
ffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi
1:00082
12
p
¼ 0:04 (15.60)
PF ¼ 0:55 (15.61)
6 10 14 18 22
0.96
0.97
0.98
0.99
1
Number of phases (m)
(A)
(B)
Efficiency
8 12 16 20
6 10 14 18 22 24
Number of phases (m)
8 12 16 20
(C)
6 10 14 18 22 24
Number of phases (m)
8 12 16 20
1
1.0002
1.0004
1.0006
1.0008
1.001
Form
factor
0.005
0.015
0.025
0.035
0.045
Ripple
factor
FIG. 15.21 Characteristics of the number of phases versus (A) efficiency,
(B) form factor, and (C) ripple factor.
–Vm
0
Vm
p/6 p/3 p/2 2p/3 5p/6 p 7p/6 4p/3 3p/2 4p/511p/6 2p
wt
van vbn vcn vdn ven
vfn
FIG. 15.22 Six-phase supply waveforms.
475
15 Multiphase Converters
20. 15.3.5.2 Six-Phase Double-Bridge Full-Wave
Uncontrolled Rectifiers
Two circuits of the six-phase bridge full-wave diode rectifiers
are shown in Fig. 15.24 and are called as a six-phase bridge cir-
cuit and hexagon bridge circuit [31]. In this case, each diode
conducts for 60 degrees in a cycle. The average output voltage
is given by Eq. (15.62):
VDC ¼
2
π=3
ð
2π
3
π
3
Vm sin ωtdωt ¼
6Vm
π
(15.62)
15.3.5.3 Six-Phase Half-Wave Controlled Rectifiers
The six-phase half-wave controlled rectifiers are shown in
Fig. 15.25 [31]. Each thyristor conducts for π/3 radians in a
cycle. The firing angle α¼ωtπ/3 in the range of 0–2π/3.
The average output voltage is
VDC ¼
1
π=3
ð
2π
3 + α
π
3 + α
Vm sin ωtdωt ¼
3Vm
π
cos α (15.63)
Load
Vm
Idc
VDC
Vm
Load
Vm
IDC
VDC
3Vm
(A) (B)
FIG. 15.23 Six-phase half-wave diode rectifiers: (A) Y/Y circuit and (B) Δ/Y circuit.
Load
Va
3Vm
VDC
IDC
Neutral line may or
may not be connected
Load
VDC IDC
3Vm
3Vm
Vm
(B)
(A)
FIG. 15.24 Six-phase full-wave uncontrolled rectifiers: (A) six-phase bridge circuit and (B) six-phase hexagon bridge circuit.
476 A. Iqbal et al.
21. Vrms ¼
ffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi
1
π=3
ð
2π
3 + α
π
3 + α
Vm sin ωt
ð Þ2
dωt
2
6
6
4
3
7
7
5
v
u
u
u
u
u
t
¼ Vm
ffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi
ffi
1
2
+
3
ffiffiffi
3
p
4π
cos α
s
(15.64)
FF ¼
Vrms
Vdc
¼ 1:0008 (15.65)
RF ¼
ffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi
1:00082
12
p
¼ 0:042 (15.66)
PF ¼ 0:956 (15.67)
From Eq. (15.63), it is clear that the output voltage can have
positive (απ/2) and negative (απ/2) values. When απ/
2, the output current is (IDC ¼VDC/R), and when the firing
angle α is π/2, the output voltage can have negative values,
but the output current can only have positive values.
15.4 Multiphase DC-AC Converters
15.4.1 Modeling and Control of a Five-Phase
Voltage Source Inverter
This section is devoted to the development of a comprehensive
model of a five-phase voltage-source inverter based on space-
vector theory [32,33]. Proper modeling of voltage-source
inverters is important in devising appropriate control algo-
rithm. The complete model is broadly classified into two
groups, namely, square-wave and PWM modes based on the
operation of the inverter. The leg voltages and line voltages
along with phase voltages are illustrated. The Fourier analysis
of output phase-to-neutral voltages and nonadjacent voltages is
performed for square-wave mode. The output phase-to-neutral
voltage is shown to be essentially identical to those obtainable
with a three-phase voltage-source inverter. At each step, simu-
lation results are provided to support the analytic approach
results. The relationship between the phase and line voltages
for a five-phase system is also established.
For high-power application, stepped operation of inverter is
preferred over PWM mode to avoid switching losses. Square-
wave mode of operation is elaborated for 180 degrees conduction
mode, and the performance is evaluated in terms of harmonic
content of phase-to-neutral voltages.
15.4.1.1 Modeling of a Five-Phase VSI
Power circuit topology of a five-phase VSI is shown in
Fig. 15.26. Each switch in the circuit consists of two power semi-
conductor devices, connected in antiparallel. One of these is a
fully controllable semiconductor, such as a bipolar transistor,
MOSFET, or IGBT, while the second one is a diode. The input
of the inverter is a DC voltage, which is regarded further on as
being constant. The inverter outputs are denoted in Fig. 15.26
with lowercase symbols (a, b, c, d, and e), while the points of
connection of the outputs to inverter legs have symbols in cap-
ital letters (A,B,C,D,E). The basic operating principles of the
five-phase VSI are developed in what follows assuming the ideal
commutation and zero forward voltage drops.
15.4.1.2 Square Wave Mode of Operation
Discrete switching of power switches in an inverter leads to
stepped wave output termed as square-wave operation of the
inverter. Conventionally, 180 degrees conduction mode is con-
sidered leading to 10-step output phase voltages from the
inverter. Each switch conducts for half of the fundamental cycle,
Vm
IDC
VDC
Vm
Load Load
Vm
IDC
VDC
3Vm
(A) (B)
FIG. 15.25 Six-phase half-wave controlled rectifiers: (A) Y/Y circuit and (B) Δ/Y circuit.
477
15 Multiphase Converters
22. that is, 180 degrees. The operation of upper and lower switches is
complimentary in operation, that is, when upper switch is on, the
lower switch is off and vice versa. In real-time application, a dead
time isprovided between the turning onoflower switch and turn-
ing offofupperswitch andviceversa.The incoming powerswitch
cannot be turned on unless the outgoing switch is completely
turned off. There is a finite time for complete turnoff of a power
switching device, and hence, a dead time is to be provided. This is
done in order to avoid short circuit of the source side.
180 degrees conduction mode
Each switch is assumed to conduct for 180 degrees(half of the
fundamental cycle), and the phase delay between firing of two
switches in any subsequent two phases is equal to 360/5
degrees¼72 degrees. The driving control gate/base signals
for the 10 switches of the inverter in Fig. 15.26 are illustrated
in Fig. 15.27. One complete cycle of operation of the inverter
can be divided into 10 distinct modes indicated in Fig. 15.27
and summarized in Table 15.2. It follows from these that at
any instant in time there are five switches that are “ON” and
five switches that are “OFF.” In the 10-step mode of operation,
there are two conducting switches from the upper five and
three from the lower five or vice versa.
Space vector of phase voltages in stationary reference frame
is defined, using power variant transformation [33]:
v ¼
2
5
va + avb + a2
vc + a2
vd + a
ve
(15.68)
where a¼exp(j2π/5), a2
¼exp(j4π/5), a*¼exp(j2π/5),
a*2
¼exp(j4π/5), and * stands for a complex conjugate.
Leg voltages (i.e., voltages between points A,B,C,D, and E and
the negative rail of the DC bus N in Fig. 15.26) are considered
first. The leg voltages from Fig. 15.27 are substituted in expres-
sion (15.68) to obtain their corresponding space vectors given
as in Eq. (15.69):
v1leg
!
v2leg
!
v3leg
!
v4leg
!
v5leg
!
v6leg
!
v7leg
!
v8leg
!
v9leg
!
v10leg
!
2
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
4
3
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
5
¼
2
5
VDC 2 cos
π
5
ej0
ejπ=5
ej2π=5
ej3π=5
ej4π=5
ejπ
ej6π=5
ej7π=5
ej8π=5
ej9π=5
2
6
6
6
6
6
6
6
6
6
6
6
6
6
6
4
3
7
7
7
7
7
7
7
7
7
7
7
7
7
7
5
(15.69)
TABLE 15.2 Modes of operation of the five-phase voltage-source inverter
(10-step operation)
Mode Switches ON Terminal polarity
1 9,10,1,2,3 A+
B+
C
D
E+
2 10,1,2,3,4 A+
B+
C
D
E
3 1,2,3,4,5 A+
B+
C+
D
E
4 2,3,4,5,6 A
B+
C+
D
E
5 3,4,5,6,7 A
B+
C+
D+
E
6 4,5,6,7,8 A
B
C+
D+
E
7 5,6,7,8,9 A
B
C+
D+
E+
8 6,7,8,9,10 A
B
C
D+
E+
9 1,7,8,9,10 A+
B
C
D+
E+
10 8,9,10,1,2 A+
B
C
D
E+
5 5
5
5
2p 6p 7p 8p 9p
4p
3p
2p
0
p
p
S1
S2
S3
S4
S5
S6
S7
S8
S9
S10
1 2 3 4 5 6
Modes
5 5 5 5
8
7
10
9
FIG. 15.27 Gating signals of a five-phase voltage-source inverter in
square-wave mode.
P
N
1
6 8 10 2 4
3 5 7 9
A B C D E
a b c d e
n
Load
FIG. 15.26 Five-phase voltage-source inverter power circuit.
478 A. Iqbal et al.
23. It is seen that the leg voltages have magnitude of 2
5VDC2
cos π=5
ð Þ and are 36 degrees apart forming a decagon. There
are in total 25
¼32 switching states (base is taken as 2 because
the switching states can only assume two values either 0 (indi-
cate off state) or 1 (indicate on state)). The first 10 states are
described above, and the remaining 22 switching states are dis-
cussed in the next section.
Phase-to-neutral voltages are discussed next. Phase-to-
neutral voltages of the star-connected load are most easily
found by defining a voltage difference between the star point
n of the load and the negative rail of the DC bus N. The follow-
ing correlation then holds true:
vA ¼ va + vnN
vB ¼ vb + vnN
vC ¼ vc + vnN
vD ¼ vd + vnN
vE ¼ ve + vnN
(15.70)
Since the phase voltages in a star-connected load sum to zero
(sum of five-phase sine wave at one instant of time is zero),
the summation of Eq. (15.70) produces
vnN ¼ 1=5
ð Þ vA + vB + vC + vD + vE
ð Þ (15.71)
Substitution of (15.71) into (15.70) produces phase-to-neutral
voltages of the load in the following form:
va ¼ 4=5
ð ÞvA 1=5
ð Þ vB + vC + vD + vE
ð Þ
vb ¼ 4=5
ð ÞvB 1=5
ð Þ vA + vC + vD + vE
ð Þ
vc ¼ 4=5
ð ÞvC 1=5
ð Þ vA + vB + vD + vE
ð Þ
vd ¼ 4=5
ð ÞvD 1=5
ð Þ vA + vB + vC + vE
ð Þ
ve ¼ 4=5
ð ÞvE 1=5
ð Þ vA + vB + vC + vD
ð Þ
(15.72)
The phase voltages in different modes are obtained by substitut-
ing leg voltages into Eq. (15.72), and their space vectors are
determined using Eq. (15.68). The space vectors of phase-to-
neutral voltage are identical to the leg voltage space vectors.
The phase-to-neutral voltages for various modes are given in
Fig. 15.28.
Fourier analysis of the voltage waveforms, which relates DC
link voltage of the inverter with the output, is elaborated.
Using the definition of the Fourier series for a periodic
waveform,
v t
ð Þ ¼ Vo +
X
∞
n¼1
An cos nωt + Bn sin nωt
ð Þ (15.73)
where the coefficients of the Fourier series are given with
Vo ¼
1
T
ð
T
0
v t
ð Þdt ¼
1
2π
ð
2π
0
v θ
ð Þdθ
An ¼
2
T
ð
T
0
v t
ð Þ cos nωtdt ¼
1
π
ð
2π
0
v θ
ð Þ cos nθdθ
Bn ¼
2
T
ð
T
0
v t
ð Þ sin nωtdt ¼
1
π
ð
2π
0
v θ
ð Þ sin nθdθ
(15.74)
Observing that the waveforms possess quarter-wave symmetry
and can be conveniently taken as odd functions, one can rep-
resent phase-to-neutral voltages with the following expressions:
v t
ð Þ ¼
X
∞
n¼1
B2n1 sin 2n1
ð Þωt where B2n1
¼
4
π
ð
π
2
0
v θ
ð Þ sin 2n1
ð Þθdθ and n ¼ 1,2,3,… (15.75)
In the case of the phase-to-neutral voltage vb, shown in
Fig. 15.28, one further has for the coefficients of the Fourier
series:
B2n1 ¼
8VDC
5π 2n1
ð Þ
1 + cos 2n1
ð Þ
3π
5
cos 2n1
ð Þ
4π
5
where k ¼ 1,2,3,… (15.76)
5
p
p
5
6p
5
4p
5
2p
2p
0
Va
5
3p
5
7p
5
8p
5
9p
Vb
Vc
Vd
Ve
VDC
VDC
5
3
5
2
FIG. 15.28 Phase-to-neutral voltages of the five-phase VSI in the square-
wave mode of operation.
479
15 Multiphase Converters
24. The expression in brackets of Eq. (15.76) equals zero for all the
harmonics whose order is divisible by five. For all the other har-
monics, it equals 2.5. Hence, one can write the Fourier series of
the phase-to-neutral voltage as
v t
ð Þ ¼
2
π
VDC
sin ωt +
1
3
sin 3ωt +
1
7
sin 7ωt +
1
9
sin 9ωt +
1
11
sin 11ωt +
1
13
sin 13ωt + …
2
6
4
3
7
5
(15.77)
From (15.77), it follows that the fundamental component of the
output phase-to-neutral voltage has an rms value equal to
V1 ¼
ffiffiffi
2
p
π
VDC ¼ 0:45VDC (15.78)
From Fig. 15.28, mean square value is determined as
Mean square value ¼
1
π
2
5
VDC
2
3π
5
+
3
5
VDC
2
2π
5
#
¼
6
25
V2
DC (15.79)
Vrms ¼
ffiffiffi
6
p
5
VDC (15.80)
Total harmonic rms voltage (per unit) is given by
VHrms ¼
ffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi
Vrms
ð Þ2
V1
ð Þ2
q
¼
ffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi
ffiffiffi
6
p
5
2
ffiffiffi
2
p
π
2
s
¼ 0:193281227 (15.81)
Hence, total harmonic distortion is
THD ¼
r:m:s: total harmonic voltage
r:m:s: total voltage
¼
0:193281227
ffiffiffi
6
p
=5
¼ 0:3945336525 or 39:45%
(15.82)
This is the same voltage as obtainable with a three-phase VSI
operating in six-step mode. It is important to note at this stage
that the space vectors described by (15.68) provides mapping
of inverter voltages into a two-dimensional space. However,
since five-phase inverter essentially requires description in a
five-dimensional space, not all the harmonics contained in
(15.77) will be encompassed by the space vector of (15.68). In
particular, space vectors calculated using (15.68) will only rep-
resent harmonics of the order 10k1, k ¼ 0,1,2,3…, that is, the
first, the ninth, the eleventh, and so on. Harmonics of the order
5k, k ¼ 1,2,3… cannot appear due to the isolated neutral point.
However, harmonics of the order 5k2, k ¼ 1,3,5… are pre-
sent in (15.77) but are not encompassed by the space-vector def-
inition of (15.68). These harmonics in essence appear in the
second two-dimensional space, which requires introduction
of the second space vector for the five-phase system.
Simulation is performed to obtain the harmonic spectrum of
inverter phase voltage in 10-step mode of operation, shown in
Fig. 15.29. The DC voltage is kept at 1 p.u. The harmonic spec-
trum is in compliance with the expression (15.77) and (15.78).
The fundamental component is equal to 0.4504 pu, which
is the same as what is obtainable with a three-phase VSI. The
subharmonic components are third and seventh in Fig. 15.29,
and their magnitudes are 33.33% and 14.3%, respectively. These
0.02 0.03 0.04 0.05 0.06 0.07 0.08
–1
–0.5
0
0.5
1
Inverter
phase
'a'
voltage
(p.u.)
Time (s)
0 100 200 300 400 500 600 700 800 900 1000
0
0.2
0.4
Inverter
phase
'a'
voltage
spectrum
RMS
(p.u.)
Frequency (Hz)
FIG. 15.29 Inverter phase “a” voltage time-domain waveform and its harmonic spectrum in frequency domain (fundamental frequency is 50 Hz, fun-
damental voltage 0.4504 (pu)).
480 A. Iqbal et al.
25. subharmonics will appear in the x-y plane and will cause distor-
tion in the stator currents and consequently increase the losses
in the machine. The lowest harmonic appearing on d-q plane
are 9th and 11th with their magnitude as 11.1% and 9.1%,
respectively. These harmonic will further add to the losses in
addition to 10th-harmonic pulsating torque under steady-state
conditions.
The line-to-line voltages are expanded next. There are two
systems of line-to-line voltage, adjacent and nonadjacent, in
contrast to a three-phase system where only one line-to-line
voltage is defined. The adjacent line-to-line voltages at the
output of the five-phase inverter are defined in Fig. 15.30,
for a fictitious load. Since each line-to-line voltage is a differ-
ence of corresponding two leg voltages, the values of nonad-
jacent line-to-line voltages will produce higher magnitude
compared with the adjacent line voltages; hence, only former
case is taken up in the thesis and later is omitted from further
consideration.
There are two sets of nonadjacent line-to-line voltages. Due
to symmetry, these two sets lead to the same values of the line-
to-line voltage space vectors, with a different phase order.
Only the set vac,vbd,vce,vda,veb is analyzed for this reason.
Table 15.3 lists the states and the values for these line-to-line
voltages.
Space vectors of nonadjacent line-to-line voltages are deter-
mined once more using the defining expression (15.68) and are
summarized as
v1ll
v2ll
v3ll
v4ll
v5ll
v6ll
v7ll
v8ll
v9ll
v10ll
2
6
6
6
6
6
6
6
6
6
6
6
6
6
6
4
3
7
7
7
7
7
7
7
7
7
7
7
7
7
7
5
¼
8
5
VDC cos
π
5
cos
π
10
ejπ=10
ej3π=10
ejπ=2
ej7π=10
ej9π=10
e11π=10
ej13π=10
ej15π=10
ej17π=10
ej19π=10
2
6
6
6
6
6
6
6
6
6
6
6
6
6
6
4
3
7
7
7
7
7
7
7
7
7
7
7
7
7
7
5
(15.83)
Time-domain waveforms of nonadjacent line-to-line voltages
are illustrated in Fig. 15.31.
The Fourier analysis is further carried out for nonadjacent
line-to-line voltage following the same procedure outlined in
conjunction with Fourier analysis of phase voltages. The non-
adjacent line voltages waveform possess quarter-wave odd
symmetry; hence, the Fourier coefficient can be evaluated as
B2n1 ¼
4VDC
2n1
ð Þπ
cos 2n1
ð Þ
π
10
where n ¼ 1,2,3,…
vea
a vab b vbc c vcd d vde e
va vc vd ve
n
vb
FIG. 15.30 Adjacent line-to-line voltages of a five-phase star-
connected load.
vac
vbd
vce
vda
veb
0 p/5 p
2p/5 2p
wt
3p/5 4p/5 6p/5 7p/5 8p/5 9p/5
VDC
FIG. 15.31 Nonadjacent line-to-line voltages for 10-step operation of a
five-phase VSI.
TABLE 15.3 Nonadjacent line-to-line voltages for 180 degrees conduction mode
Switching state Switches ON Space vector vac vbd vce vda veb
1 9,10,1,2,3 v1ll VDC VDC VDC VDC 0
2 10,1,2,3,4 v2ll VDC VDC 0 VDC VDC
3 1,2,3,4,5 v3ll 0 VDC VDC VDC VDC
4 2,3,4,5,6 v4ll VDC VDC VDC 0 VDC
5 3,4,5,6,7 v5ll VDC 0 VDC VDC VDC
6 4,5,6,7,8 v6ll VDC VDC VDC VDC 0
7 5,6,7,8,9 v7ll VDC VDC 0 VDC VDC
8 6,7,8,9,10 v8ll 0 VDC VDC VDC VDC
9 7,8,9,10,1 v9ll VDC VDC VDC 0 VDC
10 8,9,10,1,2 v10ll VDC 0 VDC VDC VDC
481
15 Multiphase Converters
26. And the Fourier series of nonadjacent line-to-line voltage can
be written as
vll t
ð Þ ¼
4
π
VDC
cos
π
10
sin ωt
ð Þ +
1
3
cos
3π
10
sin 3ωt
ð Þ
+
1
7
cos
7π
10
sin 7ωt
ð Þ + …
2
6
6
4
3
7
7
5
(15.84)
Thus, the peak of the fundamental is
Vll ¼
4
π
VDC cos
π
10
¼ 1:211VDC (15.85)
From Fig. 15.31, mean square value is determined as
Mean square value ¼
1
π
VDC
ð Þ2
4π
5
¼
4
5
V2
DC (15.86)
Vrms ¼
2
ffiffiffi
5
p VDC ¼ 0:894427191VDC (15.87)
Total harmonic rms voltage (pu) is given by
VHrms ¼
ffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi
Vrms
ð Þ2
V1
ð Þ2
q
¼
ffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi
2
ffiffiffi
5
p
2
2
ffiffiffi
2
p
π
cos
π
10
2
s
¼ 0:2585208456 (15.88)
Hence, total harmonic distortion is
THD ¼
r:m:s: totalharmonic voltage
r:m:s: total voltage
¼
0:2585208456
2=
ffiffiffi
5
p
¼ 0:2890350922 or 28:9% Or 28:9035%
(15.89)
15.4.1.3 Pulse Width Modulation Mode of Operation
If a five-phase voltage-source inverter is operated in PWM
mode, apart from the already described 10 states, there are addi-
tional 22 switching states. These remaining 22 switching states
encompass three possible situations: all the states when four
switches from upper (or lower) half and one from the lower
(or upper) half of the inverter are on (states 11–20), two states
when either all the five upper (or lower) switches are “on” (states
31 and 32), and the remaining states with three switches from
the upper (lower) half and two switches from the lower (upper)
half in conduction mode (states 21–30). The corresponding
space vectors for 11–30 are obtained using Eq. (15.68), and it
is seen that the total of 32 space vectors, available in the
PWM operation, fall into four distinct categories regarding
the magnitude of the available output phase voltages. The phase
voltage space vectors are summarized in Table 15.4 for all
32 switching states and are shown in Fig. 15.32.
Since adjacent line voltage yields lower output value, only
nonadjacent line voltages are elaborated as well:
v11ll
!
v12ll
!
v13ll
!
v14ll
!
v15ll
!
v16ll
!
v17ll
!
v18ll
!
v19ll
!
v20ll
!
2
6
6
6
6
6
6
6
6
6
6
6
6
6
6
4
3
7
7
7
7
7
7
7
7
7
7
7
7
7
7
5
¼
2
5
VDC2 cos
π
10
ejπ=10
ej3π=10
ej5π=10
ej7π=10
ej9π=10
ej11π=10
ej13π=10
ej15π=10
ej17π=10
ej19π=10
2
6
6
6
6
6
6
6
6
6
6
6
6
6
6
4
3
7
7
7
7
7
7
7
7
7
7
7
7
7
7
5
(15.90)
v21ll
!
v22ll
!
v23ll
!
v24ll
!
v25ll
!
v26ll
!
v27ll
!
v28ll
!
v29ll
!
v30ll
!
2
6
6
6
6
6
6
6
6
6
6
6
6
6
6
4
3
7
7
7
7
7
7
7
7
7
7
7
7
7
7
5
¼
2
5
VDC2 cos
3π
10
ejπ=10
ej3π=10
ej5π=10
ej7π=10
ej9π=10
ej11π=10
ej13π=10
ej15π=10
ej17π=10
ej19π=10
2
6
6
6
6
6
6
6
6
6
6
6
6
6
6
4
3
7
7
7
7
7
7
7
7
7
7
7
7
7
7
5
(15.91)
TABLE 15.4 Phase-to-neutral voltage space vectors for states 1–32
Space vectors Value of the space vectors
v1phase to v10phase 2=5VDC2 cos π=5
ð Þexp jkπ=5
ð Þ for k ¼ 0,1,2…9
v11phase to v20phase 2=5VDC exp jkπ=5
ð Þ for k ¼ 0,1,2…9
v21phase to v30phase 2=5VDC2 cos 2π=5
ð Þexp jkπ=5
ð Þ for k ¼ 0,1,2…9
v31phase to v32phase 0
d
q
v1
v2
v3
v4
v5
v6
v7
v8 v9
v10
v11
v20
v19
v18
v17
v16
v15
v14
v13
v12
v21
v24
v25
v26
v27
v28
v29
v30
v22
v23
5
p
FIG. 15.32 Phase-to-neutral voltage space vectors for states 1–32 (states
31–32 are at origin) in d-q plane.
482 A. Iqbal et al.
27. 15.4.1.4 Model Transformation Using Decoupling
Matrix
Since the system under discussion is a five-phase one, the com-
plete model can be only be elaborated in five-dimensional
space. The first two-dimensional spaces are d-q, the second
one is named as x-y, and the last is zero-sequence components
that are absent due to the assumption of isolated neutral.
On the basis of the general decoupling transformation matrix
for an n-phase system, inverter voltage space vectors in the
second two-dimensional subspace (x-y) are determined with
Eq. (15.92):
vINV
xy ¼
2
5
va + a2
vb + a4
vc + avd + a3
ve
(15.92)
Thus, 32 space vectors of phase-to-neutral voltage in the x-y
plane are obtained using Eq. (15.92) and are demonstrated in
Fig. 15.33.
It can be seen from Figs. 15.32 and 15.33 that the outer deca-
gon space vectors of the d q plane map into the innermost
decagon of the x-y plane, the innermost decagon of d-q plane
forms the outer decagon of x-y plane while the middle decagon
space vector map into the same region. Further, it is observed
from the above mapping that the phase sequence a,b,c,d,e of
d q plane corresponds to a,c,e,b,d in x-y that are basically
the third harmonic voltages.
15.4.1.5 Hardware Implementation of a Five-Phase
VSI in 180 Conduction Mode
Hardware can be developed to implement the square-wave
operation of a five-phase voltage-source inverter. The hardware
can be developed using available power switch modules from
different manufacturers such as Semikron, Mitsubishi, and
Fairchild. The power switches are available in discrete form
to implement inverter system. The gate driver circuit is also
available from different manufacturers. The control can be
implemented using microcontroller, digital signal processors
(DSP), dSpace, and field-programmable gate arrays (FPGA).
The control codes can be written in C/C++. Some of the DSPs
and FPGAs are compatible with Matlab/Simulink, and hence,
control codes can be implemented directly. In FPGA, system
generator is used for writing the control code. System generator
is a library in Matlab/Simulink software. The coding is done in
the form of drag and drop in system generator.
15.4.1.6 Hardware Set-up
The control of inverter can be implemented using sophisticated
controllers such as microcontroller, digital signal processors
(DSP), dSpace, and field-programmable gate arrays (FPGA).
The output voltages from these controllers are generally
3.3 V that is not enough for turning on the IGBTs/MOS-
FETs/BJT. Further to turn off the power switching devices,
the gate capacitors are to be fully and rapidly discharged. Gate
drive circuit is thus required to match the voltage level require-
ment of turning on the power switches (about 15 V), and a dis-
charge path for the gate capacitor is needed. Hence, a gate drive
circuit is needed to successfully turn on and turn off the power
devices. The following section describes the implementation of
the control, gate drive, and power circuit using analog devices.
The complete block diagram is shown in Fig. 15.34.
Power supply is obtained from a single-phase grid and is
converted to 9-0-9 V using a transformer. The converted volt-
age of (9-0-9 V) is fed to the phase-shifting circuit shown in
Fig. 15.35, to provide appropriate phase shift for operation at
various conduction angle (the conduction angle refers to the
conduction modes of inverter, e.g., 180, 144, and 108 degrees).
The phase-shifted signal is then fed to the inverting/noninvert-
ing Schmitt trigger circuit and wave-shaping circuit (Figs. 15.36
and 15.37). The processed signal is then fed to the isolation and
driver circuit shown in Fig. 15.38. This is then finally given to
the gate of IGBTs. There are two separate circuits for upper and
lower legs of the inverter.
The power circuit is made up of IGBT SGW20N60 having a
rating of 20 A and 600 V DC, with snubber circuit consisting of
the series combination of a resistance and a capacitor with a
diode in parallel with the resistance.
15.4.1.7 Hardware Results
Experiment can be conducted for stepped operation of inverter
with 180 degrees conduction modes for star-connected five-
phase resistive load. A single-phase supply can be given to
the control circuit through the phase-shifting network. The
output of the phase-shifting circuit provides the required
five-phase output voltage by appropriately tuning it. These
five-phase signals are then further processed to generate the
gate drive circuit.
v7
5
p
x
y
v1
v2
v3
v4
v5
v6
v7
v8
v9
v10
v11
v20
v19
v18
v17
v16
v15
v14
v13
v12
v21
v22
v23
v24
v25
v26
v27
v28
v29
v30
FIG. 15.33 Phase-to-neutral voltage space vectors for states 1–32 (states
31–32 are at origin) in x-y plane.
483
15 Multiphase Converters
28. 15.4.1.8 Results of 180 Degrees Conduction Mode
The output from the Schmitt trigger circuit is presented in
Fig. 15.39. The driving control gate/base signals for the
10-step mode for legs A–B of the inverter are illustrated in
Fig. 15.40. The corresponding phase voltage thus obtained is
shown in Fig. 15.41, keeping the DC-link voltage at
60 V. The output phase voltage is called 10 step in one funda-
mental cycle (1/5Vdc, 2/5Vdc, 1/5Vdc, 2/5Vdc, 1/5Vdc, 1/5Vdc,
2/5Vdc, 1/5Vdc, 2/5Vdc, and 1/5Vdc).
Nonadjacent line voltage obtained is shown in Fig. 15.42. All
currents are measured using AC/DC current probe giving the
output of 100 mV/A.
The AC side input current is also measured and is depicted
in Fig. 15.43. The analysis is presented in the last subsection.
15.4.1.9 DSP Implementation of Step Mode
of Operation
The results obtained in Section 15.4.1.9 are verified using
implementation through TMS320F2812 DSP under the same
operating conditions. Control code is written in C++ and
run in PC. It is transferred to the DSP using serial communi-
cation cable RS232. The DSP generate 10 gating signals that
are fed to the power module of the inverter. The detail exper-
imental setup is provided in Section 15.4.1.10. All the three
conduction angles are implemented. The developed algorithm
230V
50Hz
a b
n
n–1
To Schmitt
trigger circuit
C1
C2
Cn–1 Cn
R1
R2
Rn–1
Rn
9-0-9V
FIG. 15.35 Phase-shifting circuit (PSC).
Phase
shifting
circuit
230V
50Hz
9-0-9V
Leg-voltages
Non inv. Sh. tr. and
wave shaping
ckt-1
To gates of P-bank
IGBTs
Isolation and driver
circuit P-nth
Non inv. Sh. tr. and
wave shaping
ckt-n
Inverting Sh. tr. and
wave shaping
ckt-1
Isolation and driver
circuit P-1st
Inverting Sh. tr. and
wave shaping
ckt-n
Isolation and driver
circuit N-1st
Isolation and driver
circuit P-nth
To gates of N-bank
IGBTs
FIG. 15.34 Block diagram of the control circuit.
+
7
6
4
3
2
+Vcc
–Vcc
+Vcc
a-input
from
P
.S.C.
+Vcc
741
OA79
BC547
Noninverting Schmitt trigger and wave shaping circuit
To ‘P’
isolation
and driver
circuit
For
Adj. of
dead
time
1k
10k
1k
1k
1k
FIG. 15.36 Noninverting Schmitt trigger and wave-shaping circuit.
484 A. Iqbal et al.
29. +
7
6
4
3
2
+Vcc
–Vcc
–Vcc
a-input
from
P
.S.C.
+Vcc
741
OA79
Inverting Schmitt trigger and wave shaping circuit
To ‘N’
isolation
and driver
circuit
For
adj. of
dead
time
BC547
1k
1k
1k
1k
10k
FIG. 15.37 Inverting Schmitt trigger and wave-shaping circuit.
Q1 To gate of ‘P’ bank of Mosfet
1
2
4
5
1
2
4
5
To source of ‘P’ bank of Mosfet
To gate of ‘N’ bank of Mosfet
To source of ‘N’ Mosfet
From ‘P’
waveshaping
circuit
From ‘N’
waveshaping
circuit
1
2
2
1
5
5
4
4
Q4
Q3
Q2
+Vcc-B
+Vcc-A
OC1
OC3
OC2
OC4
R3
R4
R2
R2
R1
R1
R3
R4
FIG. 15.38 Gate driver circuit.
FIG. 15.39 Output of wave-shaping circuit for 180 degrees conduction
mode for leg A–B.
FIG. 15.40 Gate drive signals for legs A–B for 180 degrees conduction
mode.
485
15 Multiphase Converters
30. is verified using a star-connected resistive load and a five-phase
induction machine.
15.4.1.10 180 Degrees Conduction Mode
The inverter is operated in 180 degrees conduction mode, and a
five-phase star-connected resistive load is connected across the
output terminal. The resulting phase voltage, nonadjacent line
voltages are illustrated in Figs. 15.44 and 15.45, respectively.
It is observed that the phase voltage generated using cheap
analog-circuit-based inverter shown in Fig. 15.41 is identical
to the one obtained using DSP as shown in Fig. 15.44. Similarly,
the nonadjacent line voltage of Fig. 15.42 is identical to the one
shown in Fig. 15.45. This verifies the correct design of the
analog-based inverter and also verifies the DSP code. The same
study is carried out using a five-phase induction motor as a
load. The resulting voltage and stator current waveforms are
presented in Fig. 15.46. The waveform is typical for such load.
15.4.2 Carrier-Based PWM
15.4.2.1 With Zero Sequence Signal
Carrier-based sinusoidal PWM is the most popular and widely
used PWM technique because of their simple implementation
in both analog and digital realization [32,34]. The principle of
carrier-based PWM true for a three-phase VSI is also applicable
to a multiphase VSI. The PWM signal is generated by comparing
a sinusoidal modulating signal with a triangular (double edge) or
a saw-tooth (single edge) carrier signal. The frequency of the
carrier is normally kept much higher compared to the
FIG. 15.41 Output phase “a–d” voltages for 180 degrees
conduction mode.
FIG. 15.42 Nonadjacent line voltage for 180 degrees conduction mode
with DC-link voltage equal to 180 V.
FIG. 15.43 AC side input current for 180 degrees conduction mode.
FIG. 15.44 Output phase voltage for 180 degrees conduction mode.
486 A. Iqbal et al.
31. modulating signal. The principle of operation of a carrier-based
PWM modulator is shown in Fig. 15.47, and generation of PWM
waveform is illustrated in Fig. 15.48. Modulation signals are
obtained using five fundamental sinusoidal signals (displaced
in time by α ¼ 2π=5), which are summed with an appropriate
zero-sequence signal. These modulation signals are compared
with high-frequency carrier signal (saw-tooth or triangular
shape), and all five switching functions for inverter legs are
obtained directly. In general, modulation signal can be expressed
as
vi t
ð Þ ¼ v∗
i t
ð Þ + vnN t
ð Þ (15.93)
where i ¼ a,b,c,d,e and vnN represents zero-sequence signal
and vi* is fundamental sinusoidal signals. Zero-sequence signal
represents a degree of freedom that exits in the structure of a
carrier-based modulator, and it is used to modify modulation
signal waveforms and thus to obtain different modulation
schemes. Continuous PWM schemes are characterized by the
presence of switching activity in each of the inverter legs over
the carrier signal period, as long as peak value of the modula-
tion signal does not exceed the carrier magnitude.
The following relationship holds true in Fig. 15.48:
t +
n t
n ¼ vnts (15.94)
where
t +
n ¼
1
2
+ vn
ts (15.95)
0
–0.5Vdc
t = nts t = (n + 1)ts
PWM
wave
Modulating
signal
Carrier
ts
vn
0.5V
DC
0.5V
DC
0.5t–
n 0.5t–
n
t+
n
FIG. 15.48 PWM waveform generation in carrier-based sinusoidal
method.
FIG. 15.46 Nonadjacent line voltage and stator current.
Carrier signal
m*
a
m*
b
m*
c
m*
d
m*
e
Calculation of Zero
sequence signal
ma
mb
mc
md
me
S1
S6
S3
S8
S5
S10
S7
S2
S9
S4
FIG. 15.47 Principle of carrier-based PWM technique.
FIG. 15.45 Nonadjacent line voltage for 180 degrees conduction mode.
487
15 Multiphase Converters