Fall11_4_13GezaJoos_IntegrationAndInterconnectionOfDistributedEnergyResources.ppt

McGill University G. Joos
1
Integration and Interconnection of
Distributed Energy Resources
Geza Joos, Professor
Electric Energy Systems Laboratory
Department of Electrical and
Computer Engineering
McGill University
4 November 2013
University of Illinois Urbana-Champaign

2
Overview and issues addressed
 Background
 Distributed generation and resources – definition and classification
 Benefits and constraints
 Grid integration issues
 Grid interconnection and relevant standards
 Distribution systems standards
 Steady state and transient operating requirements
 Protection requirements
 General requirements – types of protection
 Islanding detection
 Concluding comments
 Distributed energy resources – microgrids and isolated systems
 Future scenarios

Electrical power system – renewable generation
3
Conventional
Renewables
Transmission
Generation
Industry
Transpor-
tation
Commercial
Storage
Distribution
FACTS
Custom Power
HVDC
Residential

Future electric distribution systems – a scenario
4
(Microgrid)
(Microgrid)

5
Distributed generation – definition – classification
 A subset of Distributed Energy Resources (DER), comprising
electrical generators and electricity storage systems
 Size – from the kW (1) to the MW (10-20) range
 Energy resource
 Renewables – biomass, solar (concentrating and photovoltaic), wind,
small hydro
 Fossil fuels – microturbines, engine-generator sets
 Electrical storage – batteries (Lead-Acid, Li-Ion)
 Other – fuel cells (hydrogen source required)
 Connection
 Grid connected – distribution grid, dispersed or embedded generation,
may be connected close to the load center, voltage and frequency st by
the electric power system
 Isolated systems – voltage and frequency set by a reference generator

6
Distributed generation – definition – features
 Not centrally planned (CIGRE) – is often installed, owned and
operated by an independent power producer (IPP)
 Not centrally dispatched (CIGRE) – IPP paid for the energy
produced and may be required to provide ancillary services
(reactive power, voltage support, frequency support and regulation)
 Connection – at any point in the electric power system (IEEE)
 Interconnection studies required to determine impact on the grid
 May modify operation of the distribution grid
 Types of distributed generation
 Dispatchable (if desired) – engine-generator systems (natural gas,
biogas, small hydro)
 Non dispatchable (unless associated with electricity storage) – wind,
solar

7
Distributed generation – installations
 Typical installations, from large to small
 Industrial – Generating plants on industrial sites, high efficiency, in
combined heat and power (CHP) configurations
 Commercial
 Residential installations, typically solar panels (PV)
 Features of smaller power dispersed generation
 Can typically be deployed in a large number of units
 Not necessarily integrated in the generation dispatch, not under the
control of the power system operator (location, sizing, etc)

Distributed generation – drivers
 Promoting the use of local energy sources –
wind, solar, hydro, biomass, biogas, others
 Creating local revenue streams (electricity
sales)
 Creating employment opportunities
(manufacturing, erection, maintenance,
operation)
 Responding to public interest and concerns
about the environment – public acceptance can
be secured
 Green power – Greenhouse Gas (GHG)
reduction
8

Distributed generation – technical benefits
 Enhanced reliability – generation close to the load
 Peak load shaving – reduction of peak demand
 Infrastructure expansion deferral – local generation
 Distribution (and transmission) system loss
reduction – generation close to load centers
 Lower grid integration costs – local generation
reduces size of connection to the main grid
 Distribution voltage connection (rather than
transmission) – ease of installation and lower cost
 Voltage support of weak distribution grids
9

Distributed generation – typical installations
 Typical power plant types
 Hydraulic, 5-10 MW
 Biomass, 5-10 MW
 Biogas, 5-10 MW
 Wind, 10-25 MW
 Total installed power (2011): 61
plants, 350 MW
 Connection: MV grid (25 kV,
nominal 10 MW feeders typical
for Canadian utilities)
10
Ref: Presentation Hydro-Quebec Distribution, 2011

Hydro-Quebec – on-going projects 2011-2015
 Biomass
 4 plants
 25 MW on MV grid
 Commissioning 2012-2013
 Small hydro
 8 plants
 Wind power plants
 5 plants
11

DG connection to the grid – options
 Connection options
 Distribution network – low (LV), typically 600 V, and up to 500 kW
 Distribution network - medium voltage (MV), up to 69 kV, typically 25
kV, up to 10-20 MW
 Transmission network – aggregated units, typically 100 MW or more
 Power system impacts
 Distribution – local, typically radial systems
 Transmission – system wide, typically meshed systems
 Differing responsibilities and concerns
 Distribution – power quality (voltage), short circuit levels
 Transmission – stability, voltage support, generation dispatch
 Integration constraints – in relation to the electric power grid
 Power quality – should not be deteriorated
 Power supply reliability and security – should not be compromised
12

Integration and interconnection issues
 Integration of the generation into existing grids – constraints
 Operating constraints – maximum power (IPP paid for kWh produced),
desired operation at minimum reactive power (unity power factor)
 Dealing with variability and balancing requirements (if integrated into
generation dispatch) – characteristic of wind and solar installations
 Integration into the generation dispatch – requires monitoring, energy
production forecasting
 Interconnection into the existing grid – constraints
 Connection to legacy systems – protection coordination, transformer
and line loading, impact on system losses
 Reverse power flow – from end-user/producer to substation
 Increased short circuit current – DG contribution
 Operational issues – grid support requirements and contribution
13

Specific DG interconnection issues
 Generation power output variability
 Short term fluctuations – flicker (wind, solar)
 Long term fluctuations – voltage regulation, voltage rise at connection
 Reactive power / Voltage regulation – coordination
 Reactive compensation – interaction with switched capacitor (pf)
 Voltage regulation – impact on tap-changing transformer operation
 Impact on Volt/Var compensation – interference
 Harmonics and static power converter filter interaction
 Voltage distortion produced by power converter current harmonics
 Resonances with system compensating capacitors
 Islanding and microgrid operation
 Operation in grid connected and islanded modes – transfer
 Microgrids – possibility of islanded operation – aid to system restoration
14

DG interconnection and control requirements
 Reactive power and power factor control – required
 Voltage regulation – may be required (using reactive power)
 Synchronization – to the electric power system
 Response to voltage disturbances – steady state and transient
 Response to frequency disturbances – steady state and transient
 Anti-islanding – usually required (to avoid safety hazards)
 Fault, internal and external – overcurrent protection
 Power quality – harmonics, voltage distortion (flicker)
 Grounding, isolation
 Operation and fault monitoring
 Grid support – larger units

16
General DG standards
 Distributed resources (DR) standards
 IEEE 1547, Standard for Interconnecting Distributed Resources with
Electric Power Systems and applies to DR less than 10 MW
 Generally applicable standards for the connection of electric
equipment to the electric grid.
 IEEE in North America and IEC in Europe, cover harmonic interference
and electrical impacts on the grid.
 Most commonly used are the IEEE 519 and the IEC 61000 series.
 Utility interconnection grid codes and regulations – issued by
regional grid operators as conditions for connecting DGs to the
electric grid

Operational requirements – larger installations
 Based in part on conventional generation (synchronous) – may
apply to DGs connected to the distribution grid
 Voltage regulation – may be enabled
 Frequency regulation – may be required
 Low voltage ride through (LVRT) – may be required
 Power curtailment and external tripping control – may be required
 Control of rate of change of active power – ramp rates
 Other features – typically required for large wind farms (> 100 MW,
transmission connected), may be required for farms > 5-25 MW
 control of active power on demand
 reactive power on demand
 inertial response for short term frequency support
 Power System Stabilization functions (PSS) – special function
17

DG protection issues – general considerations
 Operational requirements
 Distribution system – must be protected from influences caused by DG
during faults and abnormal operating conditions
 DG – must be protected from faults within DG and from faults and
abnormal operating conditions caused by distribution circuits
 Specific considerations
 Impact of different DG technologies on short circuit contribution and
voltage support under faults – induction generators, synchronous
generators, static power converters (inverters)
 Impact of power flow directionality (reversal) on existing distribution
system protection
 Instantaneous reclosing following temporary faults
 Utility breaker reclosing before DG has disconnected – may lead to out-
of-phase switching – avoided by disconnecting the DG during the auto-
reclosing dead time (as low as 0.2 s)

19
Protection system – role and requirements
 Role – to detect and isolate only the faulty section of a system so
that to maintain the security and the stability of the system
 Abnormal conditions – include effect of short circuits, over-
frequency, overvoltages, unbalanced currents, over/under
frequency, etc.
 Protection system requirements
 rated adequately
 selective – will respond only to adverse events within their zones of
protection
 dependable – will operate when required
 secure – will not operate when not required
 Faults seen by the DG
 Short circuits on the feeder
 Loss of mains – feeder opening and islanding

20
Protection functions of a DG interconnection
-
cb1
~
T1 PCC -LV
bus
cb2
L1
Line1
L2
cb5
cb4
Line2 Line3
L4
cb8
T3
R7
cb7
L3
DG1 DG2
T2
R7
PCC -HV
bus
S
cb
TL
PCC - HV side PCC - LV side DG - LV side
Distance Automatic recloser Frequency (over and under frequency)
Pilot differential Fuses Voltage (over and under voltage)
Phase directional overcurrent Voltage (over and under voltage) Overcurrent (instantaneous and delayed)
Ground directional overcurrent Overcurrent (instantaneous) Loss of mains (islanding)
Automatic recloser Underfrequency Synchronization
Undervoltage Phase directional overcurrent Loss of earth (grounding)
Overvoltage Ground directional overcurrent Neutral overcurrent
Transformer differential Negative sequence (voltage, current)
Directional overcurrent Reverse power flow
Zero sequence Generator (loss of excitation, differential)
Distance relay

DG islanding detection – requirements
 Unintentional islanding defined as DG continuing to energize part of
distribution system when connection(s) with area-EPS are severed
(also referred to as “loss of mains”)
 IEEE 1547 - the DG shall cease to energize the Area EPS circuit to
which it is connected prior to reclosure by the Area EPS
 Repercussions of an island remaining energized include:
 Personnel safety at risk
 Poor power quality within the energized island
 Possibility of damage to connected equipment within the island,
including DG (due to voltage and frequency variations)
 Utility grid codes may allow islanded operation during major
outages – may help restore service in distribution system
21

Islanding detection techniques – passive
 Passive approaches
 Frequency relays (Under/Over-frequency) - use of the active power
mismatch between island load and DG production levels
 Voltage relays (Under/Over Voltage) - based on voltage variations
occurring during islanding, resulting from reactive power mismatch
 ROCOF relays (Rate Of Change Of Frequency – resulting from real
power mismatch in the case an island is created
 Reactive power rate of change – resulting from reactive power
mismatch in the case an island is created
 Other approaches
 Active protection – based on difference in area-EPS response at DG
site when islanded; injection of signature signals at specific intervals
 Communication-based protection – using a communication link
between DG and area EPS (usually at the substation level) to convey
info on loss of mains (and possibly activate a transfer-trip)
22

Alternative approach – intelligent relays
 Alternative (intelligent) proposed approach – passive, using only
measured signals (current, voltage and derived signals)
 Use of a multivariate approach to develop a data base of islanding
patterns
 Use of data mining to extract features from the running of a large
number of operating conditions (normal) and contingencies (faults)
 Use of extracted features to develop decision trees that define relay
settings
23

DG variables monitored – multivariable approach
24

Feature extraction – methodology
 Data Mining – a hierarchical procedure that has the ability to
identify the most critical DG variables for islanding pattern
detection, or protection handles
 Decision Trees – define decision nodes; every decision node uses
different DG variables to proceed with decision making on
identifying the islanding events
 Training data set – islanding (contingencies) and non-islanding
events
 Time dependent decision trees generated – extracted at different
time steps up to the maximum time considered/allowable
 Choice of decision tree for relay setting (best) – based on
Dependability (ability to detect an islanding event as such) and
Security (ability to identify a non-islanding event as such) indices
25

Performance requirements – islanding detection
 Requirements - defining maximum permissible islanding detection
time (typically 0.5 to 2 s)
 Performance indices
 Dependability and Security indices
 Speed of response, or detection time
 Existence of non detection zones
 Constraints
 accounting for Interconnection Protection response times (reclosers)
 detection of islanding and tripping before utility attempts reclosing (out
of phase reclosing may be damageable)
 Nature of relay and impact on performance requirements – short
circuit detection needs to be faster that islanding detection – allows
additional to refine the decision tree
26

Real Time Simulator set up – basic relay testing
27
Master subsystem
Slave subsystem #2
Slave subsystem #1
Islanding protection relay
Feature
Extractor
Voltage and
Current at
DG end
Decision
Tree
Tripping
Signal
Utility
SC level:
1000MVA
X/R: 10
T1
15 MVA
120k- 25kV
B-1
CB-1
B-2
L-1
B-8
L-10
T2
L-11
15 MVA
2.4kV- 25kV
CB-4
B-9
B-11
B-18
DG
10MVA
CB-2
B-10
Distribution
system
Part 1
Distribution
system
Part 2
Islanding
relay

Decision trees – typical results
28
Δf ≥ 0.16
Δf ≥ -0.1
NO
Islanding
Islanding
NO
YES
Q ≥ 0.1
YES
Non-Islanding
NO
Δf < 0
YES
Islanding
NO
Non-Islanding
YES

Comparative performance – relay settings
29
Protective Device Setting Time delay
Intelligent Decision Tree 100 ms
Under Frequency 59.7 Hz 100 ms
Over Frequency 60.5 Hz 100 ms
ROCOF 0.1,0.25,0.5 Hz/s 0ms, 50ms

Dependability indices – comparative evaluation
30

Security indices – comparative evaluation
31

Non detection zones – comparative evaluation
32

Feasibility and performance of intelligent relays
 The proposed data mining approach is capable of
 Identifying the DG variables that capture the signature of islanding
events, in any given time interval
 Recommending variables and thresholds for protection relay setting
 The islanding intelligent relay
 Operates within prescribed time requirements (or faster)
 Can be configured for delayed operation possible
 Dependability and security indices typical better than existing passive
techniques
 Offers improved performance, including smaller non detection zones
 Can be configured for different types of DG (rotating and power
converters based), multiple DG systems and mixed DG type systems
 Can also be used for short circuit detection (including high impedance
faults) and other types of faults
33

Impact of DG technology on protection design
 DG operation dependent upon the type of generator used
 Rotating converters: synchronous and induction generators
 Static power converter interfaces (inverter based): wind turbine (Type
4), solar power converters
 Mixed: doubly-fed induction generators (wind turbine, Type 3)
 Impact of the type of generator connected to the grid on protection
design
 Short circuit level – typically lower in inverter based systems (1-2 pu)
 Transients – fully controlled in inverter based systems, dependent on
controller settings
 Speed of response of real and reactive power injection – typically much
faster in inverter based systems
 Real and reactive power capability and control – independent control in
inverter based systems
34

DER integration – opportunities in microgrids
 DER integration into distribution systems
 As individual systems, either generation or storage, connected to a
feeder or in a substation
 Integrated into a self managed system, or microgrid
 Aggregated to form a Virtual Power Plant
 Microgrid definition – a distribution system featuring
 Sufficient local generation to allow operation in islanded mode
 A number of distributed generators and storage systems, including
generation based on renewable energy resources
 A local energy management system
 A single connection to the electric power system, with possibility of
islanded operation
 The controllers required to allow connection and disconnection and
interaction with the main
35

Microgrid – types and uses
 Microgrid deployment drivers – general and current
 Increasing the resiliency and reliability of critical infrastructure and
specific entities, in the context of exceptional events (storms) –
reducing dependence on central generation and the transmission grid
 Facilitating the integrating renewable energy resources – managing
variability locally
 Taking advantage of available local energy resources – renewables
and fossil fuels (shale gas)
 Reducing greenhouse gases and reliance on fossil fuels – costs
 Types, applications and loads
 Military bases – embedded or remote
 Large self managed entities – university campuses, prisons
 Industrial and commercial installations
 Communities – managing storage and generation locally
36

Isolated/autonomous grids – applying DER
37
Grid
Interface
ESS Community
loads
Wind
generator(s)
Diesel
plant
Dump
load
PCS
Photo-
voltaics
Synchronous
generator
Solar
Wind
Battery
storage
Distributed
Energy
Resources
Conventional
Generation
Isolated
Microgrid

Benefits of storage and demand response
 In conjunction with renewable DG
 Reducing power variations in variable and intermittent generation
 Ability to provide voltage support and voltage regulation
 Enabling operation of DG at peak power and efficiency
 Power quality – voltage sag and flicker mitigation
 Possibility of islanded operation – microgrid operation
 Distribution system benefits
 Ability to dispatch/store energy and manage peak demand
 Reduced line loading – managing line congestion
 Frequency regulation, black start, reactive power
 Ability to provide other ancillary services
 Ability to perform arbitrage on electricity prices – market context
38

Electrical storage technologies
39
Discharge
Period (h)
0.0001
0.0010
0.0100
0.1000
1.0000
10.000
0.001 0.01 0.1 1 10 100 1000 10000
Power Rating (MW)
CAES
Pumped
Hydro
NaS
Redox
Flow
Lead
Acid
Battery
Flywheel
Double
Layer
Capacitor SMES
Source: Fraunhofer UMSIGHT

Demand response – characteristics
 Available loads
 Electric hot water heaters – thermal storage
 Other curtailable loads – on critical
 Electric vehicle battery storage systems
 Features of loads
 Dispersed – low power, large numbers are required
 Availability – short duty cycles
 Controllability – usually only in curtailment, possibly as additional laod
 Duration of service – limited curtailment
40

Storage vs demand response – interchangeable?
 Demand response
 Benefits: instantaneous response
 Drawbacks: unavailability, discrete control, requires a large number of
loads (stochastic behavior)
 Others: no power quality issues, but discrete steps
 Operational: energy restoration time management
 Implementation, hardware: minimal
 Electrical storage
 Benefits: fully controllable, can inject energy into the system
 Drawbacks, implementation: complex, requires power electronic
converters, life expectancy, maintenance
 Other: losses (standby), energy efficiency
 Operational: recharging management
41

Distributed energy reources – scenarios 2020
 Scenario 1 – Low DG penetration (<10 %), connection mostly to the
MV grid – business as usual
 Reduction of impact on existing grid – power quality (flicker, voltage
variation)
 Source of power (MW) – limited contribution to voltage and frequency
regulation
 Islanding required in case of loss of mains
 Scenario 2 – Increase in DER penetration (> 20 %?), connection
mostly to the MV grid – individual or in microgrids
 Integration into the generation dispatch – need for monitoring and
forecasting production (wind and solar)
 Participation in ancillary services – voltage and frequency regulation
 Requirements to remain connected for temporary loss of mains – low
voltage ride through
42

Distributed energy resources – scenarios 2020
 Scenario 3 – Increase in the penetration of DER, with connection to
the MV grid and the low voltage grid – PV panels, smaller units,
controllable loads, including electric vehicles
 For MV connections, same considerations as for Scenario 2
 For low voltage connections (residential, commercial), with a large
number of units, a number of outstanding questions
 Integration in generation dispatch – included?
 Participation in ancillary services – frequency/voltage regulation?
 Role of smart grids in managing a large penetration
 Financial consideration – generation (feed-in tariffs), ancillary services
 impacts on the grid – power quality (voltage rise), distribution system
loading
43

Fall11_4_13GezaJoos_IntegrationAndInterconnectionOfDistributedEnergyResources.ppt

Recommended

Recommended

More Related Content

Similar to Fall11_4_13GezaJoos_IntegrationAndInterconnectionOfDistributedEnergyResources.ppt

Similar to Fall11_4_13GezaJoos_IntegrationAndInterconnectionOfDistributedEnergyResources.ppt (20)

More from gulie

More from gulie (20)

Recently uploaded

Recently uploaded (20)

Fall11_4_13GezaJoos_IntegrationAndInterconnectionOfDistributedEnergyResources.ppt