1) Four engineering students designed and built a low-cost, efficient, and easy to operate three-wheeled electric scooter called a Segway.
2) The Segway is powered by batteries and a motor and controller and is intended for indoor use on large campuses to reduce travel time compared to walking.
3) The students researched parts, created a 3D design, manufactured components as needed, and assembled the Segway to prove it is possible to build such a vehicle at a low cost with high performance for limited-distance transportation.
Development and Performance of Electro Hydraulic ExcavatorYogeshIJTSRD
The heavy earth moving machineries HEMM like hydraulic excavators play a major role in the construction and mining industries. In an industry of mining and construction, a hydraulic excavator plays a major role in action to perform a carry an heavy load. Employing the technology of automation, an alternative solution is made to replace the manual operation. By addressing the concept of automation in construction, the inevitable usage of embedded is accumulated to introduce in earthmovers. In a mass production or construction site, unplanned work would lead to time consuming and fault. To overcome the major disadvantage of time consuming, so implementation of automation is made on excavators. This could be made workers do other work sequentially with half monitoring the working process of excavator. This also favors the firm or industry to increase the work capability with an adequate number of laborers. K. S Mohan Raj | A Arun Negemiya | C Sangeevi "Development and Performance of Electro-Hydraulic Excavator" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-5 | Issue-5 , August 2021, URL: https://www.ijtsrd.com/papers/ijtsrd44966.pdf Paper URL: https://www.ijtsrd.com/engineering/mechanical-engineering/44966/development-and-performance-of-electrohydraulic-excavator/k-s-mohan-raj
Harvesting Renewable Energy by Using Human Foot StepYogeshIJTSRD
Man has used tremendous amount of energy for his daily needs. Due to this a lot of energy resources have been exhausted and wasted. Proposal for the utilization of waste energy of foot power with human locomotion is very much relevant and important for highly populated countries like India where the railway station, temples etc., are overcrowded all round the clock. In this paper the force energy is produced by human footsteps and the force energy is converted into mechanical energy by rack and pinion mechanism, electricity is produced by dc generator. And this power source has many applications as in agriculture, home application and street lighting and as energy source for sensors in remote locations. This thesis is all about generating electricity when people walk on the Floor. Think about the forces you exert which is wasted when a person walks by. The idea is to convert the weight energy to electrical energy The Power generating floor intends to translate the kinetic energy to the electrical power. Energy Crisis is the main issue of world these days. The motto of this research work is to face this crisis somehow. Though it won’t meet the requirement of electricity but as a matter of fact if we are able to design a power generating floor that can produce 100W on just 12 steps, then for 120 steps we can produce 1000 Watt and if we install such type of 100 floors with this system then it can produce 1MegaWatt. Which itself is an achievement to make it significant. Vinod Kumar Jaiswal | H. P. S. Kang "Harvesting Renewable Energy by Using Human Foot Step" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-5 | Issue-5 , August 2021, URL: https://www.ijtsrd.com/papers/ijtsrd44983.pdf Paper URL: https://www.ijtsrd.com/engineering/mechanical-engineering/44983/harvesting-renewable-energy-by-using-human-foot-step/vinod-kumar-jaiswal
Analysis of factors for enhancing energy conservation in indian railway works...eSAT Publishing House
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology
Development and Performance of Electro Hydraulic ExcavatorYogeshIJTSRD
The heavy earth moving machineries HEMM like hydraulic excavators play a major role in the construction and mining industries. In an industry of mining and construction, a hydraulic excavator plays a major role in action to perform a carry an heavy load. Employing the technology of automation, an alternative solution is made to replace the manual operation. By addressing the concept of automation in construction, the inevitable usage of embedded is accumulated to introduce in earthmovers. In a mass production or construction site, unplanned work would lead to time consuming and fault. To overcome the major disadvantage of time consuming, so implementation of automation is made on excavators. This could be made workers do other work sequentially with half monitoring the working process of excavator. This also favors the firm or industry to increase the work capability with an adequate number of laborers. K. S Mohan Raj | A Arun Negemiya | C Sangeevi "Development and Performance of Electro-Hydraulic Excavator" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-5 | Issue-5 , August 2021, URL: https://www.ijtsrd.com/papers/ijtsrd44966.pdf Paper URL: https://www.ijtsrd.com/engineering/mechanical-engineering/44966/development-and-performance-of-electrohydraulic-excavator/k-s-mohan-raj
Harvesting Renewable Energy by Using Human Foot StepYogeshIJTSRD
Man has used tremendous amount of energy for his daily needs. Due to this a lot of energy resources have been exhausted and wasted. Proposal for the utilization of waste energy of foot power with human locomotion is very much relevant and important for highly populated countries like India where the railway station, temples etc., are overcrowded all round the clock. In this paper the force energy is produced by human footsteps and the force energy is converted into mechanical energy by rack and pinion mechanism, electricity is produced by dc generator. And this power source has many applications as in agriculture, home application and street lighting and as energy source for sensors in remote locations. This thesis is all about generating electricity when people walk on the Floor. Think about the forces you exert which is wasted when a person walks by. The idea is to convert the weight energy to electrical energy The Power generating floor intends to translate the kinetic energy to the electrical power. Energy Crisis is the main issue of world these days. The motto of this research work is to face this crisis somehow. Though it won’t meet the requirement of electricity but as a matter of fact if we are able to design a power generating floor that can produce 100W on just 12 steps, then for 120 steps we can produce 1000 Watt and if we install such type of 100 floors with this system then it can produce 1MegaWatt. Which itself is an achievement to make it significant. Vinod Kumar Jaiswal | H. P. S. Kang "Harvesting Renewable Energy by Using Human Foot Step" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-5 | Issue-5 , August 2021, URL: https://www.ijtsrd.com/papers/ijtsrd44983.pdf Paper URL: https://www.ijtsrd.com/engineering/mechanical-engineering/44983/harvesting-renewable-energy-by-using-human-foot-step/vinod-kumar-jaiswal
Analysis of factors for enhancing energy conservation in indian railway works...eSAT Publishing House
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology
Module price trend has declined with the increased solar PV demand & competition among the industry. The trend has been studied & forecast has been evaluated by Gensol for the modules supplied from South East Asia especially China to India from September 2013 to January 2019. The following points are highlighted:
1) Global & India Solar PV Installations & Forecast (GW)
2) Solar PV System Cost Trend Global & India 2014-2018
3) Module Price Trend (2014- 2018) & Forecast (2019 -2026)
4) Quarterly Variation in Module Price Trend YoY in %
5) Solar PV Demand in India 2017 Vs 2018
Review: Composite Flywheel for High Speed ApplicationAM Publications
Flywheel is a device to smoothen the cyclic fluctuation of speed change when delivering constant output
power from the engine. It has no influence on the mean speed of the prime mover. It has no influence on the varying
load demand on the prime mover or the delivered power from the prime mover. In the forgoing discussion, it is
observed that turning moment diagrams for the cycle show period during which torque is in excess of the mean torque
responsible for the constant power output and also periods during which the torque is less than the mean torque. Thus
the speed of the flywheel would increase during period of excess of torque during the cycle and the speed will fall
during the period of the deficit torque during the cycle. Thus a flywheel stores energy and releases energy during the
cycle without affecting mean energy output. Thus a properly designed flywheel has to ensure the cyclic fluctuations of
speed within prescribed limits preferably as small as possible. The main objective of our project is to reduce weight of
automobile by using composite material. In this Project Work taking Flywheel as an Automobile component and
applying FEA analysis using ANSYS to optimize weight and strength of flywheel. Here Performing Analysis on metal
flywheel, carbon fiber flywheel and composite i.e. metal and carbon fiber flywheel. By using ANSYS stresses obtained
& compared with analytical calculations, also weight is compared. Composite flywheel made from steel rim & carbon
fiber body will be safe for automobile applications like F1 car. From analysis & analytical results composite flywheel
for automobile can be selected.
MOST VIEWED ARTICLE FOR A YEAR IN ACADEMIA FOR MSEJmsejjournal
This paper presents a low speed permanent magnetic based generator which is suitable for supplying generating power from bicycle motion and application in providing energy for bicycle front and rear lightsor electronics devices. The dynamo have a hub axel, a hub housing rotatable mounted around the hub axel with bearing, a planetary drive that increases the rotational speed of the permanent magnet, and the power generating mechanism with coil fitted to hub axel that has connected to the output connector. In such a hub dynamo, the magnet rotates faster than the bicycle wheel so that power output is high even at the normal bicycle speeds.
Module price trend has declined with the increased solar PV demand & competition among the industry. The trend has been studied & forecast has been evaluated by Gensol for the modules supplied from South East Asia especially China to India from September 2013 to January 2019. The following points are highlighted:
1) Global & India Solar PV Installations & Forecast (GW)
2) Solar PV System Cost Trend Global & India 2014-2018
3) Module Price Trend (2014- 2018) & Forecast (2019 -2026)
4) Quarterly Variation in Module Price Trend YoY in %
5) Solar PV Demand in India 2017 Vs 2018
Review: Composite Flywheel for High Speed ApplicationAM Publications
Flywheel is a device to smoothen the cyclic fluctuation of speed change when delivering constant output
power from the engine. It has no influence on the mean speed of the prime mover. It has no influence on the varying
load demand on the prime mover or the delivered power from the prime mover. In the forgoing discussion, it is
observed that turning moment diagrams for the cycle show period during which torque is in excess of the mean torque
responsible for the constant power output and also periods during which the torque is less than the mean torque. Thus
the speed of the flywheel would increase during period of excess of torque during the cycle and the speed will fall
during the period of the deficit torque during the cycle. Thus a flywheel stores energy and releases energy during the
cycle without affecting mean energy output. Thus a properly designed flywheel has to ensure the cyclic fluctuations of
speed within prescribed limits preferably as small as possible. The main objective of our project is to reduce weight of
automobile by using composite material. In this Project Work taking Flywheel as an Automobile component and
applying FEA analysis using ANSYS to optimize weight and strength of flywheel. Here Performing Analysis on metal
flywheel, carbon fiber flywheel and composite i.e. metal and carbon fiber flywheel. By using ANSYS stresses obtained
& compared with analytical calculations, also weight is compared. Composite flywheel made from steel rim & carbon
fiber body will be safe for automobile applications like F1 car. From analysis & analytical results composite flywheel
for automobile can be selected.
MOST VIEWED ARTICLE FOR A YEAR IN ACADEMIA FOR MSEJmsejjournal
This paper presents a low speed permanent magnetic based generator which is suitable for supplying generating power from bicycle motion and application in providing energy for bicycle front and rear lightsor electronics devices. The dynamo have a hub axel, a hub housing rotatable mounted around the hub axel with bearing, a planetary drive that increases the rotational speed of the permanent magnet, and the power generating mechanism with coil fitted to hub axel that has connected to the output connector. In such a hub dynamo, the magnet rotates faster than the bicycle wheel so that power output is high even at the normal bicycle speeds.
In a world where environment protection and energy conversion are growing concerns,the development of solar vehicle has taken on an accele ration pace. The dream of having commercially viable solar vehicle is becoming a rea lity. EV�s are gradually available in the market. This opportunity is taken towards design an d development of Solar two wheeler. Solar vehicle is a multi-disciplinary subject which covers broad and complex aspects. However,it has core technologies,namely propulsio n technology,energy source technology,storage and control technology. As energy source s olar panel is used and developed voltage is stored in battery and used for the drive the hub motor which is used as rare wheel of the vehicle.
Water scarcity is the lack of fresh water resources to meet the standard water demand. There are two type of water scarcity. One is physical. The other is economic water scarcity.
Sachpazis:Terzaghi Bearing Capacity Estimation in simple terms with Calculati...Dr.Costas Sachpazis
Terzaghi's soil bearing capacity theory, developed by Karl Terzaghi, is a fundamental principle in geotechnical engineering used to determine the bearing capacity of shallow foundations. This theory provides a method to calculate the ultimate bearing capacity of soil, which is the maximum load per unit area that the soil can support without undergoing shear failure. The Calculation HTML Code included.
TECHNICAL TRAINING MANUAL GENERAL FAMILIARIZATION COURSEDuvanRamosGarzon1
AIRCRAFT GENERAL
The Single Aisle is the most advanced family aircraft in service today, with fly-by-wire flight controls.
The A318, A319, A320 and A321 are twin-engine subsonic medium range aircraft.
The family offers a choice of engines
Overview of the fundamental roles in Hydropower generation and the components involved in wider Electrical Engineering.
This paper presents the design and construction of hydroelectric dams from the hydrologist’s survey of the valley before construction, all aspects and involved disciplines, fluid dynamics, structural engineering, generation and mains frequency regulation to the very transmission of power through the network in the United Kingdom.
Author: Robbie Edward Sayers
Collaborators and co editors: Charlie Sims and Connor Healey.
(C) 2024 Robbie E. Sayers
Welcome to WIPAC Monthly the magazine brought to you by the LinkedIn Group Water Industry Process Automation & Control.
In this month's edition, along with this month's industry news to celebrate the 13 years since the group was created we have articles including
A case study of the used of Advanced Process Control at the Wastewater Treatment works at Lleida in Spain
A look back on an article on smart wastewater networks in order to see how the industry has measured up in the interim around the adoption of Digital Transformation in the Water Industry.
Event Management System Vb Net Project Report.pdfKamal Acharya
In present era, the scopes of information technology growing with a very fast .We do not see any are untouched from this industry. The scope of information technology has become wider includes: Business and industry. Household Business, Communication, Education, Entertainment, Science, Medicine, Engineering, Distance Learning, Weather Forecasting. Carrier Searching and so on.
My project named “Event Management System” is software that store and maintained all events coordinated in college. It also helpful to print related reports. My project will help to record the events coordinated by faculties with their Name, Event subject, date & details in an efficient & effective ways.
In my system we have to make a system by which a user can record all events coordinated by a particular faculty. In our proposed system some more featured are added which differs it from the existing system such as security.
Forklift Classes Overview by Intella PartsIntella Parts
Discover the different forklift classes and their specific applications. Learn how to choose the right forklift for your needs to ensure safety, efficiency, and compliance in your operations.
For more technical information, visit our website https://intellaparts.com