This file contains slides on Transient Heat conduction: Part-I
The slides were prepared while teaching Heat Transfer course to the M.Tech. students in Mechanical Engineering Dept. of St. Joseph Engineering College, Vamanjoor, Mangalore, India, during Sept. – Dec. 2010. Contents: Lumped system analysis – criteria for lumped system analysis – Biot and Fourier Numbers – Response time of a thermocouple - One-dimensional transient conduction in large plane walls, long cylinders and spheres when Bi > 0.1 – one-term approximation - Heisler and Grober charts- Problems
Lectures on Heat Transfer - Introduction - Applications - Fundamentals - Gove...tmuliya
This file contains Introduction to Heat Transfer and Fundamental laws governing heat transfer.
The slides were prepared while teaching Heat Transfer course to the M.Tech. students in Mechanical Engineering Dept. of St. Joseph Engineering College, Vamanjoor, Mangalore, India.
Heat transfer due to emission of electromagnetic waves is known as thermal radiation. Heat transfer through radiation takes place in form of electromagnetic waves mainly in the infrared region. Radiation emitted by a body is a consequence of thermal agitation of its composing molecules. The underlying mechanisms and the concepts involved are discussed in the ppt
This file contains slides on Transient Heat conduction: Part-I
The slides were prepared while teaching Heat Transfer course to the M.Tech. students in Mechanical Engineering Dept. of St. Joseph Engineering College, Vamanjoor, Mangalore, India, during Sept. – Dec. 2010. Contents: Lumped system analysis – criteria for lumped system analysis – Biot and Fourier Numbers – Response time of a thermocouple - One-dimensional transient conduction in large plane walls, long cylinders and spheres when Bi > 0.1 – one-term approximation - Heisler and Grober charts- Problems
Lectures on Heat Transfer - Introduction - Applications - Fundamentals - Gove...tmuliya
This file contains Introduction to Heat Transfer and Fundamental laws governing heat transfer.
The slides were prepared while teaching Heat Transfer course to the M.Tech. students in Mechanical Engineering Dept. of St. Joseph Engineering College, Vamanjoor, Mangalore, India.
Heat transfer due to emission of electromagnetic waves is known as thermal radiation. Heat transfer through radiation takes place in form of electromagnetic waves mainly in the infrared region. Radiation emitted by a body is a consequence of thermal agitation of its composing molecules. The underlying mechanisms and the concepts involved are discussed in the ppt
This chapter contains:-.
Analytical Methods of two dimensional steady state heat conduction
Finite difference Method application on two dimensional steady state heat conduction.
Finite difference method on irregular shape of a system
heat conduction and its mechanisms ,thermal conductivity,Fourier law,variation of thermal conductivity with temperature in metals and solids,steady and unsteady states,biot and Fourier numbers and their significance, Lumped heat analysis
Recognize numerous types of heat exchangers, and classify them.
Develop an awareness of fouling on surfaces, and determine the overall heat transfer coefficient for a heat exchanger.
Perform a general energy analysis on heat exchangers.
Obtain a relation for the logarithmic mean temperature difference for use in the LMTD method, and modify it for different types of heat exchangers using the correction factor.
Develop relations for effectiveness, and analyze heat exchangers when outlet temperatures are not known using the effectiveness-NTU method.
Know the primary considerations in the selection of heat exchangers.
Heat transfer from extended surfaces (or fins)tmuliya
This file contains slides on Heat Transfer from Extended Surfaces (FINS). The slides were prepared while teaching Heat Transfer course to the M.Tech. students in Mechanical Engineering Dept. of St. Joseph Engineering College, Vamanjoor, Mangalore, India.
Contents: Governing differential eqn – different boundary conditions – temp. distribution and heat transfer rate for: infinitely long fin, fin with insulated end, fin losing heat from its end, and fin with specified temperatures at its ends – performance of fins - ‘fin efficiency’ and ‘fin effectiveness’ – fins of non-uniform cross-section- thermal resistance and total surface efficiency of fins – estimation of error in temperature measurement - Problems
Thermal Radiation-II- View factors and Radiation energy exchange between blac...tmuliya
This file contains slides on THERMAL RADIATION-II: View factors and Radiation energy exchange between black bodies.
The slides were prepared while teaching Heat Transfer course to the M.Tech. students in Mechanical Engineering Dept. of St. Joseph Engineering College, Vamanjoor, Mangalore, India, during Sept. – Dec. 2010.
Contents: View factor – general relations – radiation energy exchange between black bodies – properties of view factor and view factor algebra – view factor formulas and graphs – Problems
Definition and Requirements
Types of Heat Exchangers
The Overall Heat Transfer Coefficient
The Convection Heat Transfer Coefficients—Forced Convection
Heat Exchanger Analysis
Heat Exchanger Design and Performance Analysis
Summary of lmtd and e ntu. The Log Mean Temperature Difference Method (LMTD) The Logarithmic Mean Temperature Difference(LMTD) is valid only for heat exchanger with one shell pass and one tube pass. For multiple number of shell and tube passes the flow pattern in a heat exchanger is neither purely co-current nor purely counter-current. The temperature difference between the hot and cold fluids varies along the heat exchanger. It is convenient to have a mean temperature difference Tm for use in the relation. s mQ UA T
3. The mean temperature difference in a heat transfer process depends on the direction of fluid flows involved in the process. The primary and secondary fluid in an heat exchanger process may flow in the same direction - parallel flow or cocurrent flow in the opposite direction - countercurrent flow or perpendicular to each other - cross flow
Numerical methods in Transient-heat-conductiontmuliya
This file contains slides on Numerical methods in Transient heat conduction.
The slides were prepared while teaching Heat Transfer course to the M.Tech. students in Mechanical Engineering Dept. of St. Joseph Engineering College, Vamanjoor, Mangalore, India, during Sept. – Dec. 2010.
Contents: Finite difference eqns. by energy balance – Explicit and Implicit methods – 1-D transient conduction in a plane wall – stability criterion – Problems - 2-D transient heat conduction – Finite diff. eqns. for interior nodes – Explicit and Implicit methods - stability criterion – difference eqns for different boundary conditions – Accuracy considerations – discretization error and round–off error - Problems
This chapter contains:-.
Analytical Methods of two dimensional steady state heat conduction
Finite difference Method application on two dimensional steady state heat conduction.
Finite difference method on irregular shape of a system
heat conduction and its mechanisms ,thermal conductivity,Fourier law,variation of thermal conductivity with temperature in metals and solids,steady and unsteady states,biot and Fourier numbers and their significance, Lumped heat analysis
Recognize numerous types of heat exchangers, and classify them.
Develop an awareness of fouling on surfaces, and determine the overall heat transfer coefficient for a heat exchanger.
Perform a general energy analysis on heat exchangers.
Obtain a relation for the logarithmic mean temperature difference for use in the LMTD method, and modify it for different types of heat exchangers using the correction factor.
Develop relations for effectiveness, and analyze heat exchangers when outlet temperatures are not known using the effectiveness-NTU method.
Know the primary considerations in the selection of heat exchangers.
Heat transfer from extended surfaces (or fins)tmuliya
This file contains slides on Heat Transfer from Extended Surfaces (FINS). The slides were prepared while teaching Heat Transfer course to the M.Tech. students in Mechanical Engineering Dept. of St. Joseph Engineering College, Vamanjoor, Mangalore, India.
Contents: Governing differential eqn – different boundary conditions – temp. distribution and heat transfer rate for: infinitely long fin, fin with insulated end, fin losing heat from its end, and fin with specified temperatures at its ends – performance of fins - ‘fin efficiency’ and ‘fin effectiveness’ – fins of non-uniform cross-section- thermal resistance and total surface efficiency of fins – estimation of error in temperature measurement - Problems
Thermal Radiation-II- View factors and Radiation energy exchange between blac...tmuliya
This file contains slides on THERMAL RADIATION-II: View factors and Radiation energy exchange between black bodies.
The slides were prepared while teaching Heat Transfer course to the M.Tech. students in Mechanical Engineering Dept. of St. Joseph Engineering College, Vamanjoor, Mangalore, India, during Sept. – Dec. 2010.
Contents: View factor – general relations – radiation energy exchange between black bodies – properties of view factor and view factor algebra – view factor formulas and graphs – Problems
Definition and Requirements
Types of Heat Exchangers
The Overall Heat Transfer Coefficient
The Convection Heat Transfer Coefficients—Forced Convection
Heat Exchanger Analysis
Heat Exchanger Design and Performance Analysis
Summary of lmtd and e ntu. The Log Mean Temperature Difference Method (LMTD) The Logarithmic Mean Temperature Difference(LMTD) is valid only for heat exchanger with one shell pass and one tube pass. For multiple number of shell and tube passes the flow pattern in a heat exchanger is neither purely co-current nor purely counter-current. The temperature difference between the hot and cold fluids varies along the heat exchanger. It is convenient to have a mean temperature difference Tm for use in the relation. s mQ UA T
3. The mean temperature difference in a heat transfer process depends on the direction of fluid flows involved in the process. The primary and secondary fluid in an heat exchanger process may flow in the same direction - parallel flow or cocurrent flow in the opposite direction - countercurrent flow or perpendicular to each other - cross flow
Numerical methods in Transient-heat-conductiontmuliya
This file contains slides on Numerical methods in Transient heat conduction.
The slides were prepared while teaching Heat Transfer course to the M.Tech. students in Mechanical Engineering Dept. of St. Joseph Engineering College, Vamanjoor, Mangalore, India, during Sept. – Dec. 2010.
Contents: Finite difference eqns. by energy balance – Explicit and Implicit methods – 1-D transient conduction in a plane wall – stability criterion – Problems - 2-D transient heat conduction – Finite diff. eqns. for interior nodes – Explicit and Implicit methods - stability criterion – difference eqns for different boundary conditions – Accuracy considerations – discretization error and round–off error - Problems
Very useful for the beginners in the field of heat and the mass transfer field. It also gives the idea about the different modes of heat transfer and the measurement of energy transfer rate.
As companies examine their total cost of operations, energy usage and heat recovery deliver cost savings through increased energy utilization and efficiency. Heat exchangers offer companies the opportunity to reuse energy generated for a specific purpose instead of venting that energy to the atmosphere. Shell and tube heat exchangers are in wide use throughout the Food, Dairy, Beverage, Pharmaceutical, Chemicals, Petroleum Refining, and Utility industries. This paper briefly explores three modes of heat transfer and basic designs found in shell and tube heat exchangers. Also included are several case studies from different industries where
Enerquip’s heat exchangers have saved the operators energy and money.
Student information management system project report ii.pdfKamal Acharya
Our project explains about the student management. This project mainly explains the various actions related to student details. This project shows some ease in adding, editing and deleting the student details. It also provides a less time consuming process for viewing, adding, editing and deleting the marks of the students.
Saudi Arabia stands as a titan in the global energy landscape, renowned for its abundant oil and gas resources. It's the largest exporter of petroleum and holds some of the world's most significant reserves. Let's delve into the top 10 oil and gas projects shaping Saudi Arabia's energy future in 2024.
Cosmetic shop management system project report.pdfKamal Acharya
Buying new cosmetic products is difficult. It can even be scary for those who have sensitive skin and are prone to skin trouble. The information needed to alleviate this problem is on the back of each product, but it's thought to interpret those ingredient lists unless you have a background in chemistry.
Instead of buying and hoping for the best, we can use data science to help us predict which products may be good fits for us. It includes various function programs to do the above mentioned tasks.
Data file handling has been effectively used in the program.
The automated cosmetic shop management system should deal with the automation of general workflow and administration process of the shop. The main processes of the system focus on customer's request where the system is able to search the most appropriate products and deliver it to the customers. It should help the employees to quickly identify the list of cosmetic product that have reached the minimum quantity and also keep a track of expired date for each cosmetic product. It should help the employees to find the rack number in which the product is placed.It is also Faster and more efficient way.
Final project report on grocery store management system..pdfKamal Acharya
In today’s fast-changing business environment, it’s extremely important to be able to respond to client needs in the most effective and timely manner. If your customers wish to see your business online and have instant access to your products or services.
Online Grocery Store is an e-commerce website, which retails various grocery products. This project allows viewing various products available enables registered users to purchase desired products instantly using Paytm, UPI payment processor (Instant Pay) and also can place order by using Cash on Delivery (Pay Later) option. This project provides an easy access to Administrators and Managers to view orders placed using Pay Later and Instant Pay options.
In order to develop an e-commerce website, a number of Technologies must be studied and understood. These include multi-tiered architecture, server and client-side scripting techniques, implementation technologies, programming language (such as PHP, HTML, CSS, JavaScript) and MySQL relational databases. This is a project with the objective to develop a basic website where a consumer is provided with a shopping cart website and also to know about the technologies used to develop such a website.
This document will discuss each of the underlying technologies to create and implement an e- commerce website.
Industrial Training at Shahjalal Fertilizer Company Limited (SFCL)MdTanvirMahtab2
This presentation is about the working procedure of Shahjalal Fertilizer Company Limited (SFCL). A Govt. owned Company of Bangladesh Chemical Industries Corporation under Ministry of Industries.
Explore the innovative world of trenchless pipe repair with our comprehensive guide, "The Benefits and Techniques of Trenchless Pipe Repair." This document delves into the modern methods of repairing underground pipes without the need for extensive excavation, highlighting the numerous advantages and the latest techniques used in the industry.
Learn about the cost savings, reduced environmental impact, and minimal disruption associated with trenchless technology. Discover detailed explanations of popular techniques such as pipe bursting, cured-in-place pipe (CIPP) lining, and directional drilling. Understand how these methods can be applied to various types of infrastructure, from residential plumbing to large-scale municipal systems.
Ideal for homeowners, contractors, engineers, and anyone interested in modern plumbing solutions, this guide provides valuable insights into why trenchless pipe repair is becoming the preferred choice for pipe rehabilitation. Stay informed about the latest advancements and best practices in the field.
Overview of the fundamental roles in Hydropower generation and the components involved in wider Electrical Engineering.
This paper presents the design and construction of hydroelectric dams from the hydrologist’s survey of the valley before construction, all aspects and involved disciplines, fluid dynamics, structural engineering, generation and mains frequency regulation to the very transmission of power through the network in the United Kingdom.
Author: Robbie Edward Sayers
Collaborators and co editors: Charlie Sims and Connor Healey.
(C) 2024 Robbie E. Sayers
About
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.
Technical Specifications
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
Key Features
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface
• Compatible with MAFI CCR system
• Copatiable with IDM8000 CCR
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
Application
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.
Immunizing Image Classifiers Against Localized Adversary Attacksgerogepatton
This paper addresses the vulnerability of deep learning models, particularly convolutional neural networks
(CNN)s, to adversarial attacks and presents a proactive training technique designed to counter them. We
introduce a novel volumization algorithm, which transforms 2D images into 3D volumetric representations.
When combined with 3D convolution and deep curriculum learning optimization (CLO), itsignificantly improves
the immunity of models against localized universal attacks by up to 40%. We evaluate our proposed approach
using contemporary CNN architectures and the modified Canadian Institute for Advanced Research (CIFAR-10
and CIFAR-100) and ImageNet Large Scale Visual Recognition Challenge (ILSVRC12) datasets, showcasing
accuracy improvements over previous techniques. The results indicate that the combination of the volumetric
input and curriculum learning holds significant promise for mitigating adversarial attacks without necessitating
adversary training.
Immunizing Image Classifiers Against Localized Adversary Attacks
Heat transfer chapter one and two
1. 11/2/2017 Heat Transfer 1
HEAT TRANSFER
(MEng 3121)
INTROUCTION
TO
HEAT TRANSFER
Chapter 1
Debre Markos University
Mechanical Engineering
Department
Prepared and presented by:
Tariku Negash
E-mail: thismuch2015@gmail.com
Lecturer at Mechanical Engineering
Department Institute of Technology, Debre
Markos University, Debre Markos, Ethiopia
2. 11/2/2017Heat Transfer
2
Mass transfer is the net movement of mass from
one location, usually meaning stream, phase,
fraction or component, to another. Or
From the region of high concentration to the
lower concentration.
Examples: Evaporation of water from a pond to the
atmosphere.
Flow of energy due solely to a temperature difference
from 2nd Law of Thermodynamics, heat flows
in direction of decreasing temperature
heat energy can be transported through a solid,
liquid, gas, or vacuum.
1.1 Definition of Heat and Mass Transfer
a. Heat Transfer
b. Mass Transfer
3. 11/2/2017Heat Transfer
3
1.2 MODES OF HEAT TRANSFER
Heat can be transferred in three different modes:
Conduction, Convection, & Radiation.
A. Conduction: The transfer of energy from the more energetic particles
of a substance to the adjacent less energetic ones as a result of
interactions between the particles.
In solids, it is due to the combination of
vibrations of the molecules in a lattice and the
energy transport by free electrons (i.e. solids
in metallic form).
In gases and liquids, conduction is due to the
collisions and diffusion of the molecules
during their random motion.
4. 11/2/2017Heat Transfer
4
The rate of heat conduction through a plane layer is proportional to
the temperature difference across the layer and the heat transfer
area, but is inversely proportional to the thickness of the layer.
Where:-
K = Thermal conductivity, : A measure of the
ability of a material to conduct heat.
dT/dx = Temperature gradient : The slope of the
temperature curve on a T-x diagram.
5. 11/2/2017Heat Transfer
5
Material Thermal conductivity
k (W.m-1.K-1)
Diamond 2450
Cu 385
Al 205
Brick 0.2
Glass 0.8
Body fat 0.2
Water 0.6
Wood 0.2
Styrofoam 0.01
Air 0.024
Thermal conductivity, k
property of the material
kdiamond very high: perfect heat
sink, e.g. for high power laser
diodes
khuman low: core temp relatively
constant (37oC)
kair very low: good insulator
* home insulation
* woolen clothing
* windows double glazing
i.e, Metals – good conductors: electrons
transfer energy from hot to cold
6. 11/2/2017Heat Transfer
6
Example:. Cold air flows above the hot copper plate.
B. Convection: The mode of energy transfer between a solid surface
and the adjacent liquid or gas that is in motion, and it involves the
combined effects of conduction and fluid motion.
Natural Convection:
Fluid motion occurs due to density variations
caused by temperature difference
Types of convection
Forced convection:
Fluid motion caused by an external agency
In the absence of any bulk fluid motion, heat transfer between a solid
surface and the adjacent fluid is by pure conduction.
7. 11/2/2017Heat Transfer
7
Newton’s law of cooling
h convection heat transfer coefficient, W/m2 · °C
As the surface area through which convection heat transfer takes place
Ts the surface temperature
T the temperature of the fluid sufficiently far from the surface
C. Radiation: The energy emitted by matter in the form of electromagnetic
waves (or photons) as a result of the changes in the electronic
configurations of the atoms or molecules.
• Unlike conduction and convection, the transfer of heat by radiation does
not require the presence of an intervening medium.
In fact, heat transfer by radiation is fastest (at
the speed of light) and it suffers no attenuation
in a vacuum.
This is how the energy of the sun reaches the
earth.
8. 11/2/2017Heat Transfer
8
In heat transfer studies we are interested in thermal radiation, which is
the form of radiation emitted by bodies because of their temperature.
All bodies at a temperature above absolute zero emit thermal radiation.
Absorption & Stefan-Boltzmann Law
Stefan–Boltzmann law
Where:-
Surface Area, A
Stefan-Boltzmann constant, σ = 5.67 x 10-8 W.m-2.K-4
Applications on radiation heat transfer
9. Think about
Why are fireplace pokers made of iron and not copper?
• Some animals have hair which is composed of solid tubular strands, while
others have hollow, air-filled tubes. Where would one more likely find the
latter animal: In cold climates, or warm?
• Two different materials at the same temperature have different emissivities.
Which one glows the brightest?
• Steel reinforcement bars add stability to concrete walls. Do they also
enhance the insulating value of concrete?
• Should you lower the blinds and draw the curtains on a hot day?
• When one steps from a shower on a cold morning, why does the tile floor
seem so much colder than the air?
• Place a wooden spoon and a metal spoon in the freezer. Which will cool
faster? After several hours, what would they feel like?
• Why do people become "flushed" when overheated?
• What is thermal energy? What is the difference between thermal energy and
heat?
11/2/2017 Heat Transfer
10. 11/2/2017 Heat Transfer 10
HEAT TRANSFER
(MEng 3121)
ONE DIMENSIONAL STEADY
STATE HEAT CONDUCTION
Chapter 2
Debre Markos University
Mechanical Engineering
Department
Prepared & presented by:
Tariku N.
Oct .2017
11. 11/2/2017Heat Transfer
11
2. ONE DIMENSIONAL STEADY STATE CONDUCTION
For example, consider the steady-state
conduction experiment.
A cylindrical rod of known material is
insulated on its lateral surface, while
its end faces are maintained at
different, with T1>T2.
2.1 The Conduction Rate Equation
The temperature difference causes conduction heat transfer in the
positive x- direction.
How qx depends on the following variables: ∆T, the temperature
difference; ∆x, the rod length; and A, the cross-sectional area.
qx = qx (∆T, ∆x, A) using a chain rule differentiate
equation : by taking one constant and two variable
12. 11/2/2017Heat Transfer
12
Proportionality may be converted to an equality by introducing a
coefficient that is a measure of the material behavior. Hence, we write
What will be qx value for metal and a plastic material for
equal values of ∆T, ∆x, and A?
qx would be smaller for the plastic than for the metal.
Why? Proportionality (∝)
Where k, the thermal conductivity (W/m.k)
Therefore, k is an important property of the material.
Evaluating this expression in the limit as ∆x→ 0, 𝑤𝑒 𝑜𝑏𝑡𝑎𝑖𝑛
For the heat rate For the heat flux
i,e, the minus sign is necessary because heat is always transferred in the
direction of decreasing temperature.
13. 11/2/2017Heat Transfer
13
Fourier's law (𝒒 𝒙
′′
): The direction of heat flow will always be normal
to a surface of constant temperature, called an isothermal surface.
The rate of heat transfer through a unit thickness of
the material per unit area per unit temperature
difference.
It depends on the physical structure of matter, atomic
and molecular, which is related to the state of the
matter.
The thermal conductivity of a material is a measure
of the ability of the material to conduct heat.
2.2.1 Thermal conductivity (K):
Fig 2.1. A simple experimental setup to determine the
thermal conductivity of a material.
2.2 Thermal Conductivity and Diffusivity
14. 11/2/2017Heat Transfer
14
A high value for thermal conductivity
indicates that the material is a good heat
conductor, and a low value indicates that
the material is a poor heat conductor or
insulator.
15. 11/2/2017Heat Transfer
15
The thermal conductivities of gases such as
air vary by a factor of 104 from those of pure
metals such as copper.
Pure crystals and metals have the highest
thermal conductivities, and gases and
insulating materials the lowest.
The mechanisms of heat conduction in different phases
of a substance.
16. 11/2/2017Heat Transfer
16
2.2.2 Thermal Diffusivity (𝜶)
In heat transfer analysis, the ratio of the thermal conductivity to the heat
capacity is an important property termed the thermal diffusivity 𝜶, which is
It measures the ability of a material to conduct thermal energy relative to its
ability to store thermal energy.
So what does it mean when materials have large and small value of 𝜶?
For a large 𝛂 will respond quickly to changes in their thermal environment, and
,For a small 𝜶 will respond more sluggishly, taking longer to reach a new
equilibrium condition.
Example: WAX
Proof its SI units and what is the similar property in fluid flow?
m2/s. This value describes how quickly a material reacts to
a change in temperature.
In order to predict cooling processes or to simulate temperature fields, the thermal
diffusivity must be known; it is a requisite for solving the Fourier Differential Equation for
unsteady heat conduction.
17. 11/2/2017Heat Transfer
17
Example 2.1: The thermal diffusivity 𝜶 is the controlling transport
property for transient conduction. Using appropriate values of k, 𝜌 , and
cp from Appendix A, (Thermophysical Properties Research Center (TPRC) at
Purdue University) show at incropera (Thermophysical Properties of Matter)
calculate for the following materials at the prescribed temperatures:
a) pure aluminum, 300 and 700 K;
b) silicon carbide, 1000 K;
c) paraffin, 300 K
19. 11/2/2017Heat Transfer
19
2.3 General Heat Conduction Equation
Heat transfer problems are also classified as being one-dimensional,
two dimensional, or three-dimensional, depending on the relative
magnitudes of heat transfer rates in different directions and the level of
accuracy desired.
In the most general case, heat transfer through a medium 3D.
That is, the temperature varies along all three primary directions within
the medium during the heat transfer process.
The temperature distribution throughout the medium at a specified
time as well as the heat transfer rate at any location, can be
described by a set of three coordinates such as the
i. Rectangular (or Cartesian) coordinate system: x, y, and z;
ii. Cylindrical coordinate system: 𝐫, 𝝓 𝑎𝑛𝑑 𝒛
iii. Spherical (or polar) coordinate system: 𝐫, 𝝓 𝑎𝑛𝑑 𝜽
20. 11/2/2017Heat Transfer
20
2.3.1 Rectangular (or Cartesian) coordinate system: x, y, and z
Consider a small rectangular element of length 𝑑x, width d y, and height dz,
and an infinitesimally small (differential) control volume, d y. 𝑑x.d z
Temperature distribution: T(x. y, z)
In the absence of motion (or with uniform
motion), there are no changes in mechanical
energy and no work being done on the system.
Only thermal forms of energy need be
considered. Specifically, if there are temperature
gradients, conduction heat transfer will occur
across each of the control surfaces.
The conduction heat rates perpendicular
to each of the control surfaces at the x-,y-,and
z- coordinate locations are indicated qx, qy,
and qz.
21. 11/2/2017Heat Transfer
21
The conduction heat rates at the opposite surfaces can
then be expressed as a Taylor series expansion where,
neglecting higher-order terms,
Within the medium there may also be an energy source term associated
with the rate of thermal energy generation. This term is represented as
q: rate at which energy is generated per unit volume (w/m3)
In addition, changes may occur in the amount of the internal thermal
energy stored by the material in the control volume.
22. 11/2/2017Heat Transfer
22
Based on applying conservation of energy to a differential control
volume through which energy transfer is exclusively by conduction.
The conduction heat rates in an isotropic material may be evaluated from
Fourier's law, Note: Isotropic material : they have the same
properties in all directions. Or, thermal
conductivity of a material to be independent of
direction.
Fibrous or composite, are some anisontropic
materials
23. 11/2/2017Heat Transfer
23
Net transfer of thermal energy into the
control volume (inflow-outflow)
p
T T T T
k k k q c
x x y y z z t
•
Thermal energy
generation
Change in thermal
energy storage
General Cartesian coordinates, of the heat diffusion equation.
In the case of constant thermal conductivity, it reduces to
Equation is called Fourier-Biot equation, and it reduces to these forms
under specified conditions:
Additional
conditions
24. 11/2/2017Heat Transfer
24
2.3.2 Cylindrical coordinate system: 𝐫, 𝝓 𝑎𝑛𝑑 𝒛
When the del operator (𝜵) of heat flux is expressed in cylindrical coordinates,
the general form of the heat flux vector and hence of Fourier's law is
Where,
25. 11/2/2017Heat Transfer
25
Differential control volume, 𝒅𝒓 ∗ 𝒓𝒅𝝓 ∗ 𝒅𝒛, for conduction analysis in
cylinderical coordinates(𝒓, 𝝓,𝒛).
After lengthy manipulations, we obtain
3.2.3 Spherical (or polar) coordinate system: 𝐫, 𝝓 𝑎𝑛𝑑 𝜽
27. 11/2/2017Heat Transfer
27
2.4 Steady Heat Conduction In Plane Walls
For one-dimensional conduction in a plane wall, temperature is a function
of the x-coordinate only and heat is transferred exclusively in this
direction.
There will be no heat transfer in a direction in which
there is no change in temperature. (isothermal).
2.4.1 Heat transfer through a plane wall: Temperature
distribution and its equivalent thermal circuit.
For steady-state conditions with no distributed source
or sink of energy within the wall, the appropriate form
of the heat equation is
No heat generation, the heat flux is a constant, independent of x. and k
is constant , the equation may be integrated twice to obtain the general
solution
(1)
(2)
28. 11/2/2017Heat Transfer
28
To obtain the constants of integration, C1 and
C2 , boundary conditions must be introduced.
x = 0 and x = L, in which case
In which, (3)
At, x = 0,
At, x = L, 𝑇𝑠,2 = 𝐶1 𝐿 + 𝐶2 = 𝐶1 𝐿+𝑇𝑠,1
𝑇𝑠,1 = 𝐶2
Therefore equ. (4) states that the temperature varies linearly with x
Substituting into equ (2) 𝑻 𝒙 = (𝑻 𝒔,𝟐−𝑻 𝒔,𝟏)
𝒙
𝑳
+ 𝑻 𝒔,𝟏 (4)
Heat rate (Fourier's law),
Equation
For the Heat Flux
(5)
(6)
Are constant,
independent
of x
29. 11/2/2017Heat Transfer
29
2.5 Thermal Resistance
Just as an electrical resistance is associated with the conduction of
electricity, a thermal resistance may be associated with the conduction of
heat.
Defining resistance as the ratio of a driving potential to the
corresponding transfer rate,
𝒂. thermal resistance for conduction in a plane wall is
For electrical conduction in the same system, Ohm's law
provides an electrical resistance of the form
b. thermal resistance for convection heat transfer at a surface. (Newton's
cooling system)
𝑅 𝑒 =
𝑉1 − 𝑉2
𝐼
30. 11/2/2017Heat Transfer
30
The equivalent thermal circuit for the plane wall with convection
surface conditions
The heat transfer rate may be determined from
separate consideration of each element in the
network.
Since qx is constant throughout the network, it
follows that
In terms of the overall temperature difference,
c. thermal resistance for radiation
and the total thermal resistance,
Rtot the heat transfer rate
31. 11/2/2017Heat Transfer
31
2.6 The Composite Wall (multilayer plane)
The composite walls that involve any number of series and parallel thermal
resistances due to layers of different materials.
2.7 Overall heat transfer coefficient (U)
With composite systems, it is often convenient to work with an overall
heat transfer coefficient U, which is defined by an expression analogous
to Newton's law of cooling. Accordingly,
𝑤ℎ𝑒𝑟𝑒 ∆T: is the overall temperature difference.(7)
32. 11/2/2017Heat Transfer
32
In general, we may write
2.7.8 Equivalent thermal circuits for a series–parallel composite wall
Draw thermal circuit for block
diagram
Or,
For case (a) it is presumed that surfaces normal to the x-direction are
isothermal, whereas for case (b) it is assumed that surfaces parallel to
the x-direction are adiabatic
33. 11/2/2017Heat Transfer
33
2.8 Thermal Contact Resistance
In the analysis of heat conduction through multilayer solids, we assumed
“perfect contact” at the interface of two layers, and thus no temperature
drop at the interface.
This would be the case when the surfaces are perfectly smooth and
they produce a perfect contact at each point.
In reality, however, even flat surfaces that appear smooth to the eye
turn out to be rather rough when examined under a microscope,
The temperature change is attributed to what is known
as the thermal contact resistance, Rt,c.
From the fig, for a unit area of the
interface, the resistance is defined as
(8) So, how Rt,c can be decrease ?
i. Increasing the joint pressure and/or reducing the
roughness of the mating surfaces.
ii. By selecting an interfacial fluid of large thermal conductivity.
34. 11/2/2017Heat Transfer
34
a. What will be occurred
if Injera baking (mitad)
is produced by mixing
clay to metal powder.
And what would be
thermal contact resistance
b/n them
b. With what material
did u recommend the clay
would mix in order
to increase thermal
Conductivity or (decrease
Rt,c)
c. Do u have any idea that
increase K of the Mitad
by using composite
materials
Think about it
35. 11/2/2017Heat Transfer
35
2.9 Radial Systems : The Cylinder
A common example is the hollow cylinder whose inner and outer surfaces
are exposed to fluids at different temperatures
For steady-state conditions with no
heat generation, the appropriate form
of the heat equation,
For Fourier's law,
where A = 2𝜋rL is the area
normal to the direction of
heat transfer.
From eq 8, the quantity (𝑘𝑟
𝑑𝑇
𝑑𝑟
= 0) is independent of r, then the conduction
heat transfer rate qr eqn 9 is constant in the radial direction. But, for the heat flux
𝑞 𝑟
′′
is dependent on radial direction
(8)
(9)
36. 11/2/2017Heat Transfer
36
Double integration for eq (8) by assuming the value of k to be
constant
To obtain the constants of integration C1 and C2 , we introduce the following
boundary conditions:
Applying these conditions to the general solution, we then obtain
Solving for C1 and C2 and substituting into the general solution, we then obtain
(10)
Now substitute eqn (10) into eqn (9) (11)
The thermal resistance for radial system: (12)
37. 11/2/2017Heat Transfer
37
For an overall heat transfer coefficient.
If U is defined in terms of the
inside area, A = 2𝜋r1L
(13)
(14)
Eqn. (13) and (14) can be yield
Arbitrary overall heat transfer coefficient
(15)
38. 11/2/2017Heat Transfer
38
2.10 The Sphere
For the differential control volume of the figure, energy conservation requires
For steady-state, one-dimensional conditions with no
heat generation. The appropriate form of Fourier's
law is
that qr=qr+dr .
Where 𝑨 = 𝟒𝝅𝒓 𝟐 is the area normal to the direction of heat transfer.
(16)
qr is constant, independent of r. eqn (16) may be expressed integral form
Assuming constant k, we then obtain
Thermal resistance for sphere
(17)
(18)
39. 11/2/2017Heat Transfer
39
2.11 Critical Thickness of Insulation : sphere and cylinder
Let us consider a layer of insulation which might
be installed around a circular pipe, (cylinder) as
shown in Figure.
The inner temperature of the insulation is fixed at
Ti, and the outer surface exposed to a
convection environment 𝑻∞.
From the thermal network the heat transfer is
Now let us manipulate this expression to determine the outer radius of
insulation 𝑟0 , which will maximize the heat transfer. The
maximization condition is
which gives the result (19)
For sphere (20)
40. 11/2/2017Heat Transfer
40
Table 2.3 One-dimensional, steady-state solutions to the heat equation with no
generation (no thermal energy generation)
Summary
41. 11/2/2017Heat Transfer
41
2.12 Conduction With Thermal Energy Generation
a. Plane wall with thermal energy Generation
Consider the Asymmetric plane wall of Figure a, in
which there is uniform energy generation per unit volume
(q is constant ) the surface is maintained at Ts,1 and Ts,2
For constant thermal conductivity k, the appropriate
form of the heat equation,
The general solution is
where C1 and C2 are the constants of integration. For the prescribed
boundary conditions,
Fig a
42. 11/2/2017Heat Transfer
42
The constants may be evaluated and are of the form
in which case the temperature distribution is
The heat flux at any point in the wall may, of course, be determined by
using Equation (21) with Fourier's law. Note, however, that with
generation the heat flux is no longer independent of x.
(21)
Fig b
For symmetric plane wall Fig b, both surfaces are
maintained at a common temperature,
𝑻 𝒔,𝟏 ≡ 𝑻 𝒔,𝟐 ≡ 𝑻 𝒔.
The temperature distribution is then symmetrical
about the mid plane, using above eqn (21)
(22)
In w/ch plane that the maximum temperature exists?
43. 11/2/2017Heat Transfer
43
The maximum temperature exists at the mid plane
in which case the temperature distribution, Equation (22) , may be
expressed as
Fig c is represented no heat transfer across the surface
(adiabatic surface at mid plane)
Fig c
Using eqn. (22), the plane walls that are perfectly
insulated on one side (x=0) and maintained at a fixed
temperature 𝑻 𝒔. on the other side (x=L).
Neglecting radiation and substituting the appropriate
rate equations, the energy balance given by Equation
Substituting from Equation 22 to obtain the temperature gradient at x = L,
it follows that Hence 𝑻 𝒔 may be computed from
knowledge of 𝑇∞. , L, and h.
(23)
(24)
44. 11/2/2017Heat Transfer
44
b. Radial system with thermal energy Generation
Heat generation may occur in a variety of radial geometries.
Consider the long, solid cylinder of figure 2a, which could represent a
current-carrying wire or a fuel element in a nuclear reactor.
For constant thermal conductivity k,
Separating variables and assuming uniform generation,
this expression may be integrated to obtain
Repeating the procedure, the general solution for the temperature distribution
becomes;
To obtain the constants of integration C1 and C2 , we apply boundary conditions:
(25)
(26)
45. 11/2/2017Heat Transfer
45
For solid cylinder the centerline is a line of symmetry (symmetry condn)
temperature distribution and the temperature gradient must be zero.
symmetrical boundary conditions (Figure b).
r = 0 and Equation 25, it is evident that C1=0
Using the surface boundary condition at r = r0 with equation 26, we then
obtain
The temperature distribution is therefore
∴ the heat rate at any radius in the cylinder may, of course, be evaluated
by using Equation (27) with Fourier's law.
(27)
Where T0 is the centerline temperature.
Evaluating Equation 27 at the centerline and dividing the result into Equation
27, we obtain the temperature distribution in non dimensional form,
(28)
46. 11/2/2017Heat Transfer
46
To relate the surface temperature, 𝑻 𝒔, to the temperature of the cold
fluid 𝑻∞, there is two methods
i. surface energy balance
ii. an overall energy balance.
Choosing the second approach, we obtain
Or, (29)
c. Sphere system with thermal energy Generation
𝟏
𝒓 𝟐
𝝏
𝝏𝒓
𝒌𝒓 𝟐
𝝏𝑻
𝝏𝒓
+
𝒒
𝒌
= 0
𝑻 𝒓 = 𝑻 𝒔 +
𝒒𝒓 𝟐
𝟐
𝟔𝒌
𝟏 −
𝒓 𝟐
𝒓 𝟐
𝟐
Eat conduction on sphere (polar) one dimension and steady state with
thermal generation
After some mathematical calculation
(30)
48. 11/2/2017Heat Transfer
48
2.13 Heat Transfer from Extended Surfaces (Fins)
Until now, we have considered heat transfer from the
boundaries of a solid to be in the same direction as
heat transfer by conduction in the solid.
In contrast, for an extended surface, the direction of
heat transfer from the boundaries is perpendicular to
the principal direction of heat transfer in the solid.
Consider a strut that connects two walls at different temperatures and
across which there is fluid flow.
With T1 >T2 temperature gradients in the x-direction sustain heat
transfer by conduction in the strut.
However, with T1 >T2 >T∞ there is concurrent heat transfer by
convection to the fluid, causing qx, and hence the magnitude of the
Temperature gradient, dT/dx, to decrease with increasing x.
49. 11/2/2017Heat Transfer
49
If T 𝒔 fixed plane wall of fig a , there are
two ways in which the heat transfer rate
may be increased.
The convection coefficient h could be increased, by
However, there are many situations for which increasing h to the maximum
possible value is either insufficient to obtain the desired heat transfer rate or
the associated costs are prohibitive (blower or pump power requirements).
i. increasing the fluid velocity, and/or the
ii. increasing fluid temperature T∞ could be reduced.
iii. by increasing the surface area across which the convection occurs on fig.
b, this may be done by employing n 𝒔 that extend from the wall into
the surrounding fluid is called fin.
a b
51. 11/2/2017Heat Transfer
51
2.13 The Fin Equation
Some typical fin configurations:
For fig a it may be of uniform cross-sectional area (A=t*w), or
Fig b its cross-sectional area may vary with the distance x from the wall.
Fig (c) an annular fin is one that is circumferentially attached to a
cylinder, and its cross section varies with radius from the wall of the
cylinder. 𝐴 𝑎 = 2𝜋𝑟
Fig (d) a pin fin, or spine, is an extended surface of circular cross
section. Pin fins may also be of uniform or non uniform cross section.
In any
A straight fin is any extended
surface that is attached to a
plane wall.
52. 11/2/2017Heat Transfer
52
It may depend on space, weight, manufacturing, and cost considerations,
as well as on the extent to which the fins reduce the surface convection
coefficient and increase the pressure drop associated with flow over the
fins.
Selection of a particular fin configuration:
i. A general form of the energy equation for a fin
Applying the conservation of energy
From Fourier's law,
Ac: the fin cross-sectional area which is vary with x
Since the conduction heat rate at x + dx may be expressed as
53. 11/2/2017Heat Transfer
53
The convection heat transfer rate may be expressed as
dAs: is the surface area of the differential element.
Or
Its solution for appropriate boundary conditions provides the temperature
distribution.
ii. Fins of Uniform Cross-Sectional Area
Each fin is attached to a base surface of
temperature T(0) = Tb and extends into a
fluid of temperature 𝑻∞
Where; P: the fin perimeter
Ac: constant the fin cross-sectional area
As : surface area = Px
(31)
Fig. Straight fins of uniform cross
section. (a) Rectangular fin. (b) Pin fin.
54. 11/2/2017Heat Transfer
54
Equation (31) reduces to
To simplify the form of this equation, we transform the dependent variable
by defining an excess temperature 𝜽 as
𝜽 𝒙 = 𝑻 𝒙 − 𝑻∞
(32)
(33)
where, since 𝑻∞ is a constant, d𝜃/𝑑𝑥 = dT/dx. Substituting Equation (33)
into Equation (32) , we then obtain
Where, 𝑚2 =
ℎ𝑃
𝐾𝐴 𝑐
Eqn. (34) is a linear, homogeneous, second-order differential
equation with constant coefficients. Its general solution is of
the form
(34)
Evaluate the constants C1 and C2 by specifying boundary conditions,
(35)
at the base of the fin (x = 0), (36)
55. 11/2/2017Heat Transfer
55
2nd condition, specified at the fin tip (x = L), may correspond to one
of four different physical situations.
Case A
Considers convection heat transfer from the fin tip.
Applying an energy balance to a control surface about this tip
Or
That is, the rate at which energy is transferred to the fluid
by convection from the tip must equal the rate at which
energy reaches the tip by conduction through the fin.
(37)
Substitute eqn. 35 in to eqn 36 and 37
And,
(37.1)
(37.2)
57. 11/2/2017Heat Transfer
57
Fin heat transfer rate qf
The amount of heat transferred from the entire fin ca be calculate with two
alternative ways, both of which involve use of the temperature
distribution.
1st The simpler procedure, and the one that we will use, involves
applying Fourier's law at the fin base. That is
Hence, knowing the temperature distribution, 𝜽 𝒙 , qf may be evaluated,
giving
(40)
2nd by using conservation of energy principles
Which is the rate at which heat is transferred by convection from the
fin must equal the rate at which it is conducted through the base of the
fin.
(39)
58. 11/2/2017Heat Transfer
58
(41)
where Af is the total, including the tip, fin
surface area.
Or, by substituting Eqn (38) in to Eqn
(41) we can get Eqn (40)
Case B: Assume when the fin tip is insulated (adiabatic)
(35)
Substituting from Equation 35 and dividing by m, we then obtain
Where,
(42)
(43)
like Eqn (35), Solving C1 and C2 by using eqn (38.1) and (43) and
substitute into eqn (35) it may be shown, after some manipulation,
(44)
Using this temperature distribution with Equation (39) , the fin heat
transfer rate is then (45)
59. 11/2/2017Heat Transfer
59
Case C: Temperature is prescribed at the fin tip
That is, the second boundary condition is 𝜽 𝑳 = 𝜽 𝑳, and the resulting
expressions are of the form
(46)
(47)
The very long fin n, is an interesting extension of
these results. In particular, as L→ ∞, 𝜽 𝑳 → 𝟎 and
it is easily verified that,
Case D: For L→ ∞
(48)
(49)
60. 11/2/2017Heat Transfer
60
Temperature distribution and heat loss for fins of uniform cross section
Summary
See A table of hyperbolic functions at Appendix B1 in your text book (Fundamentals
of Heat and Mass Transfer)
61. 11/2/2017Heat Transfer
61
2.14 Fin Performance
Recall that fins are used to increase the heat transfer from a surface by
increasing the effective surface area.
However, the fin itself represents a conduction resistance to heat
transfer from the original surface.
For this reason, there is no assurance that the heat transfer rate will
be increased through the use of fins.
Therefore, we should evaluate the fin (n) effectiveness, 𝜺 𝒇 which is,
𝜺 𝒇 =
𝒒 𝒇
𝒉𝑨 𝒄,𝒃 𝜽 𝒃
𝜺 𝒇 =
heat transfer rate with fin
heat transferexist without the fin
=
𝒒 𝒇
𝒒 𝒏𝒐𝒇
(50) Where, 𝑨 𝒄,𝒃 is the fin cross-sectional
area at the base.
By substituting eqn (49) which is at the case D
for 𝒒 𝒇 in to eqn (50) then,
𝜺 𝒇 =
𝒌𝑷
𝒉𝑨 𝒄,𝒃
(51)
62. 11/2/2017Heat Transfer
62
i. k should be as high as possible, (copper, aluminum, iron).
Aluminum is preferred: low cost and weight, resistance to corrosion.
𝒊𝒊.
𝑷
𝑨 𝒄,𝒃
should be as high as possible. (Thin plate fins and slender pin fins)
iii. Most effective in applications where h is low. (Use of fins justified if when
the medium is gas and heat transfer is by natural convection).
𝜺 𝒇 =
𝒌𝑷
𝒉𝑨 𝒄,𝒃
Increasing methods of 𝜺 𝒇 from the formula
If
𝜺 𝒇 =
𝒒 𝒇
𝒒 𝒏𝒐𝒇
Therefore, in any rational design the value of should be as large as possible,
𝜺 𝒇 ≥ 𝟐
63. 11/2/2017Heat Transfer
63
2.15 Measurement of Fin performance .
𝑹 𝒕,𝒇 =
𝜽 𝒃
𝒒 𝒇
𝒘𝒉𝒆𝒓𝒆, 𝜽 𝒃 𝒊𝒔 𝒕𝒉𝒆 𝒅𝒓𝒊𝒗𝒊𝒏𝒈 𝒑𝒐𝒕𝒆𝒏𝒕𝒊𝒂𝒍 = the d/c b/n the base
and the fluid temperature
The thermal resistance due to convection at the exposed base,
𝑹 𝒕,𝒃 =
𝟏
𝒉𝑨 𝒄,𝒃
and substituting from Equation (50) ,it follows that
𝒉𝑨 𝒄,𝒃 =
𝟏
𝑹 𝒕,𝒃
𝜺 𝒇 =
𝑹 𝒕,𝒃
𝑹 𝒕,𝒇
Hence the fin effectiveness may be interpreted as a ratio of thermal
resistances, and to increase 𝜺 𝒇 it is necessary to reduce the
conduction/convection resistance of the fin.
If the fin is to enhance heat transfer, its resistance must not exceed that of
the exposed base.
A. Fin performance in terms of a thermal resistance
(52)
(53)
(54)
64. 11/2/2017Heat Transfer
64
A. Fin performance in terms of a its efficiency (𝜼 𝒇)
𝜼 𝒇 =
Actual heat transfer rate from the fin
Ideal heat transfer rate from the fin if the entire fin were at base temperature
Case B
Case D
Where, 𝑚 =
ℎ𝑃
𝐾𝐴 𝑐
In the limiting case of zero thermal resistance or
infinite thermal conduction ( k → ∞ ) the
temperature of the fin will be uniform at the base
value of 𝑇𝑏
𝜼 𝒇 =
𝒒 𝒇
𝒒 𝒎𝒂
=
𝒒 𝒇
𝒉𝑨 𝒇 𝜽 𝒃
(55)
(56)
(57)
65. 11/2/2017Heat Transfer
65
2.16 Corrected fin length (𝑳 𝒄)
For a Case B using equation (45)
Corrected fin length of the form 𝑳 𝒄 = 𝑳 + (𝒕/𝟐)
for a rectangular fin and 𝑳 𝒄 = 𝑳 + (𝑫/𝟒) for a pin
fin.
By using equation (57)
If the width of a rectangular fin is much larger than
its thickness, w >> t, the perimeter may be
approximated as P =2w, and
Where, 𝑚 =
ℎ𝑃
𝐾𝐴 𝑐
66. 11/2/2017Heat Transfer
66
Figure 2.1 Efficiency of straight fins (rectangular, triangular, and
parabolic profiles).
(58)
Hence, as shown in Figures 2.1 and 2.2, the efficiency of a rectangular fin with tip
convection may be represented as a function of
Where,
68. 11/2/2017Heat Transfer
68
2.17 Expressions for the efficiency and surface area of several common
fin geometries are summarized in Table 2.6.
Table 2.6 Efficiency of common fin shapes
70. 11/2/2017Heat Transfer
70
2.18 Overall Surface Efficiency
In the contrast the fin efficiency 𝜼 𝒇 , which characterizes the performance of
a single fin, the overall surface efficiency 𝜼 𝟎 characterizes an array of fins
and the base surface to which they are attached
The total rate of heat transfer by convection from the fins and the prime (un finned)
surface may be expressed as
Where,
If there are N fins in the array, each of
surface area Af , and the area of the prime
h is assumed to be equivalent for the finned and prime surfaces.
𝜼 𝒇 is the efficiency of a
single fin.
surface is designated as At, the total surface area.
(59)
(60)
71. 11/2/2017Heat Transfer
71
Substituting Equation (59) into (60), it follows that
Equation (59) may be used to infer an expression for the thermal resistance
( 𝑹 𝒕,𝒇) using eqn (52) of a fin array. That is,
𝑹 𝒕,𝒇 =
𝜽 𝒃
𝒒 𝒇
(61)
(62)
Where, 𝑹 𝒕,𝟎s an effective resistance
that accounts for parallel heat flow
paths by conduction/convection in the
fins and by convection from the prime
surface.
72. 11/2/2017Heat Transfer
72
2.19 Fins attachment Methods
1st Fins are machined as
an integral part of the
wall from which they
extend more
commonly, fig a or
manufactured
separately and are
attached to the wall by
a metallurgical or
adhesive joint.
2nd By a press fit, for
which the fins are
forced into slots
machined on the wall
material. fig b
fig a
fig b
Draw thermal circuits for each array
73. 11/2/2017Heat Transfer
73
In such cases (fig b),there is a thermal contact resistance 𝑹 𝒕.𝒄, may
adversely influence overall thermal performance.
An effective circuit resistance may again be obtained, where,
with the contact resistance,
the corresponding overall surface efficiency is
Where,
In manufacturing, care must be taken to render
74. 11/2/2017Heat Transfer
74
Reference
This lecture power point adapted from
1. Yunus Cengel, Heat and Mass Transfer A Practical Approach,
3rd edition
2. Jack P. Holman, Heat Transfer, Tenth Edition.
3. Frank P. Incropera, Theodore l. Bergman, Adrienne S.
Lavine, and David P Dewitt, fundamental of Heat and Mass
Transfer, 7th edition
4. Lecture power point of heat transfer by Mehmet Kanoglu
University of Gaziantep