Fundamentals of petroleum processing lecture 5 is a presentation that defines fuel refining processes in detail. All processes such as catalytic cracking, isomerisation, reforming, alkylation, ploymerisation, delayed corking and vis-breaking are described in full detail with well illustration flow diagrams and charts.
all process involve in petroleum to get final products from crude oil like LPG, petrol, diesel, jet fuel, kerosene,neptha, heavy neptha, coke and petroleum products
Naphtha Steam Reforming Catalyst Reduction with MethanolGerard B. Hawkins
Procedure for Naphtha Steam Reforming Catalyst Reduction with Methanol
Scope
This procedure applies to the in situ reduction of VULCAN Series steam reforming catalysts using methanol cracking to form hydrogen over the catalyst in the steam reformer.
The procedure is likely to be applied to plants using only heavier feeds (e.g.: LPG and/or naphtha) and some combination of VULCAN Series catalysts.
Introduction
A small number of steam reforming plants do not have an available source of the commonly used reducing media (e.g.: hydrogen, hydrogen-rich off-gas, natural gas). These plants will usually operate on LPG and/or naphtha feed only where cracking of this hydrocarbon is not usually advised for reduction of the steam reforming catalyst ...
Naphtha catalytic reforming process is the key process in oil refining to meet the demands of gasoline fuel specifications and hydrogen gas for hydrotreating and isomerization units. But one bottleneck of high aromatics content in gasoline may restrict the naphtha reforming process due to strict environmental regulations.
These slides are developed for a part of the undergraduate course in Petroleum Refinery Engineering. The slides are also helpful for Masters level introductory course.
all process involve in petroleum to get final products from crude oil like LPG, petrol, diesel, jet fuel, kerosene,neptha, heavy neptha, coke and petroleum products
Naphtha Steam Reforming Catalyst Reduction with MethanolGerard B. Hawkins
Procedure for Naphtha Steam Reforming Catalyst Reduction with Methanol
Scope
This procedure applies to the in situ reduction of VULCAN Series steam reforming catalysts using methanol cracking to form hydrogen over the catalyst in the steam reformer.
The procedure is likely to be applied to plants using only heavier feeds (e.g.: LPG and/or naphtha) and some combination of VULCAN Series catalysts.
Introduction
A small number of steam reforming plants do not have an available source of the commonly used reducing media (e.g.: hydrogen, hydrogen-rich off-gas, natural gas). These plants will usually operate on LPG and/or naphtha feed only where cracking of this hydrocarbon is not usually advised for reduction of the steam reforming catalyst ...
Naphtha catalytic reforming process is the key process in oil refining to meet the demands of gasoline fuel specifications and hydrogen gas for hydrotreating and isomerization units. But one bottleneck of high aromatics content in gasoline may restrict the naphtha reforming process due to strict environmental regulations.
These slides are developed for a part of the undergraduate course in Petroleum Refinery Engineering. The slides are also helpful for Masters level introductory course.
Catalytic Reforming Process is one of the most important processes in the petroleum and petrochemical industries which produce high octane number gasoline.
This presentation details out all the process in an Oil Refinery. If you are looking to have a hawk eye view of all the oil refinery process, this presentation will set you on.
Simple explained.
(HTS) High Temperature Shift Catalyst (VSG-F101) - Comprehensiev OverviewGerard B. Hawkins
The high temperature shift duty introduction and theory
HTS catalyst characteristics
developments over time
Typical HTS operational problems
Improved catalysts
VULCAN Series VSG-F101 Series
Summary
24. PRODUCER GAS CLEANING METHODS.pptxRENERGISTICS
Producer gas should be cleaned from particulate and tar components using a series of gas cleaning system, such as scrubber, elutriator, and heat exchanger. The scrubber is functioning to take the particulate matters and heavy tars (primary tars) which may condense at temperature more than 200 °C out from producer gas.
COURSE LINK:
https://www.chemicalengineeringguy.com/courses/petroleum-refining/
COURSE DESCRIPTION:
The main scope of the course is to create strong basis and fundamentals regarding the processes in the Petroleum Refining. We take a look to the Oil&Gas Industry briefly and continue directly with the Refining Process. We then make a focus in each individual unit operation in the refinery.
Learn about:
* Oil& Gas Industry
* Difference between Petroleum Refining vs. Petrochemical Industry
* Overview of the most important operations and products
* Market insight (supply/demand) as well as (production/consumption)
* Several Petroleum Refineries around the World
Unit Operations & Processes
* Refining and Fractionation
* Atmospheric Distillation Column
* Vacuum Distillation
* Hydrotreating (Hydrogenation)
* Blending
* Reforming
* Isomerization
* Alkylation
* Steam Cracking
* Fluid Catalytic Cracking
* Gas Sweetening (Hydrodesulfurization)
* Coking
Components:
* Fuel Gas / Natural Gas
* Liquified Petroleum Gases (LPG)
* Propane, Butane
* Sulfur / Hydrogen Sulfide
* Gasoline / Automotive Gas Oil
* Naphtha Cuts (Light/Heavy)
* Kerosene
* Diesel
* Gasoil
* Lubricants
* Vacuum Residues
* Asphalt
* Coke
NOTE: This course is focused for Process Simulation
At the end of the course you will feel confident in the Petroleum Refining Industry. You will know the most common Process & Unit Operations as well as their distribution, production and importance in daily life.
----
Please show the love! LIKE, SHARE and SUBSCRIBE!
More likes, sharings, suscribers: MORE VIDEOS!
-----
CONTACT ME
Chemical.Engineering.Guy@Gmail.com
www.ChemicalEngineeringGuy.com
http://facebook.com/Chemical.Engineering.Guy
You speak spanish? Visit my spanish channel -www.youtube.com/ChemEngIQA
Catalytic Reforming Process is one of the most important processes in the petroleum and petrochemical industries which produce high octane number gasoline.
This presentation details out all the process in an Oil Refinery. If you are looking to have a hawk eye view of all the oil refinery process, this presentation will set you on.
Simple explained.
(HTS) High Temperature Shift Catalyst (VSG-F101) - Comprehensiev OverviewGerard B. Hawkins
The high temperature shift duty introduction and theory
HTS catalyst characteristics
developments over time
Typical HTS operational problems
Improved catalysts
VULCAN Series VSG-F101 Series
Summary
24. PRODUCER GAS CLEANING METHODS.pptxRENERGISTICS
Producer gas should be cleaned from particulate and tar components using a series of gas cleaning system, such as scrubber, elutriator, and heat exchanger. The scrubber is functioning to take the particulate matters and heavy tars (primary tars) which may condense at temperature more than 200 °C out from producer gas.
COURSE LINK:
https://www.chemicalengineeringguy.com/courses/petroleum-refining/
COURSE DESCRIPTION:
The main scope of the course is to create strong basis and fundamentals regarding the processes in the Petroleum Refining. We take a look to the Oil&Gas Industry briefly and continue directly with the Refining Process. We then make a focus in each individual unit operation in the refinery.
Learn about:
* Oil& Gas Industry
* Difference between Petroleum Refining vs. Petrochemical Industry
* Overview of the most important operations and products
* Market insight (supply/demand) as well as (production/consumption)
* Several Petroleum Refineries around the World
Unit Operations & Processes
* Refining and Fractionation
* Atmospheric Distillation Column
* Vacuum Distillation
* Hydrotreating (Hydrogenation)
* Blending
* Reforming
* Isomerization
* Alkylation
* Steam Cracking
* Fluid Catalytic Cracking
* Gas Sweetening (Hydrodesulfurization)
* Coking
Components:
* Fuel Gas / Natural Gas
* Liquified Petroleum Gases (LPG)
* Propane, Butane
* Sulfur / Hydrogen Sulfide
* Gasoline / Automotive Gas Oil
* Naphtha Cuts (Light/Heavy)
* Kerosene
* Diesel
* Gasoil
* Lubricants
* Vacuum Residues
* Asphalt
* Coke
NOTE: This course is focused for Process Simulation
At the end of the course you will feel confident in the Petroleum Refining Industry. You will know the most common Process & Unit Operations as well as their distribution, production and importance in daily life.
----
Please show the love! LIKE, SHARE and SUBSCRIBE!
More likes, sharings, suscribers: MORE VIDEOS!
-----
CONTACT ME
Chemical.Engineering.Guy@Gmail.com
www.ChemicalEngineeringGuy.com
http://facebook.com/Chemical.Engineering.Guy
You speak spanish? Visit my spanish channel -www.youtube.com/ChemEngIQA
Project of Introduction to Petroleum and Gas Engineering and Explanation of the cracking process and types.Cracking, as the name suggests, is a process in which large hydrocarbon molecules are broken down into smaller and more useful ones,The cracking products, such as ethene, propene, buta-1,3-diene and C4 alkenes, are used to make many important chemicals. Others such as branched and cyclic alkanes are added to the gasoline fraction obtained from the distillation of crude oil to enhance the octane rating.
IJERA (International journal of Engineering Research and Applications) is International online, ... peer reviewed journal. For more detail or submit your article, please visit www.ijera.com
Conference for Catalysis Webinar 2021: "The Key Role of Catalysts and Adsorb...Dr. Meritxell Vila
Energy transition is a challenge for refineries and petrochemical plants. In this sense, the role of catalysts and adsorbents will be crucial in three areas:
New schemes of refineries: crude oil to chemicals (COTC)
Production of biofuels
Production of green hydrogen
This presentation was done at Catalysis Webinar 2021, the 24th March.
conversion of waste plastic into fuel
contents
waste to fuel
wte plants around the world
flow diagram
pyrolysis of plastic
pyrolysis principal
reaction & catalytic cracking
catalys tused
figure
condenser
nitrogen cylinder
advantge
thank u
any question
Cosmetic shop management system project report.pdfKamal Acharya
Buying new cosmetic products is difficult. It can even be scary for those who have sensitive skin and are prone to skin trouble. The information needed to alleviate this problem is on the back of each product, but it's thought to interpret those ingredient lists unless you have a background in chemistry.
Instead of buying and hoping for the best, we can use data science to help us predict which products may be good fits for us. It includes various function programs to do the above mentioned tasks.
Data file handling has been effectively used in the program.
The automated cosmetic shop management system should deal with the automation of general workflow and administration process of the shop. The main processes of the system focus on customer's request where the system is able to search the most appropriate products and deliver it to the customers. It should help the employees to quickly identify the list of cosmetic product that have reached the minimum quantity and also keep a track of expired date for each cosmetic product. It should help the employees to find the rack number in which the product is placed.It is also Faster and more efficient way.
Industrial Training at Shahjalal Fertilizer Company Limited (SFCL)MdTanvirMahtab2
This presentation is about the working procedure of Shahjalal Fertilizer Company Limited (SFCL). A Govt. owned Company of Bangladesh Chemical Industries Corporation under Ministry of Industries.
Immunizing Image Classifiers Against Localized Adversary Attacksgerogepatton
This paper addresses the vulnerability of deep learning models, particularly convolutional neural networks
(CNN)s, to adversarial attacks and presents a proactive training technique designed to counter them. We
introduce a novel volumization algorithm, which transforms 2D images into 3D volumetric representations.
When combined with 3D convolution and deep curriculum learning optimization (CLO), itsignificantly improves
the immunity of models against localized universal attacks by up to 40%. We evaluate our proposed approach
using contemporary CNN architectures and the modified Canadian Institute for Advanced Research (CIFAR-10
and CIFAR-100) and ImageNet Large Scale Visual Recognition Challenge (ILSVRC12) datasets, showcasing
accuracy improvements over previous techniques. The results indicate that the combination of the volumetric
input and curriculum learning holds significant promise for mitigating adversarial attacks without necessitating
adversary training.
NUMERICAL SIMULATIONS OF HEAT AND MASS TRANSFER IN CONDENSING HEAT EXCHANGERS...ssuser7dcef0
Power plants release a large amount of water vapor into the
atmosphere through the stack. The flue gas can be a potential
source for obtaining much needed cooling water for a power
plant. If a power plant could recover and reuse a portion of this
moisture, it could reduce its total cooling water intake
requirement. One of the most practical way to recover water
from flue gas is to use a condensing heat exchanger. The power
plant could also recover latent heat due to condensation as well
as sensible heat due to lowering the flue gas exit temperature.
Additionally, harmful acids released from the stack can be
reduced in a condensing heat exchanger by acid condensation. reduced in a condensing heat exchanger by acid condensation.
Condensation of vapors in flue gas is a complicated
phenomenon since heat and mass transfer of water vapor and
various acids simultaneously occur in the presence of noncondensable
gases such as nitrogen and oxygen. Design of a
condenser depends on the knowledge and understanding of the
heat and mass transfer processes. A computer program for
numerical simulations of water (H2O) and sulfuric acid (H2SO4)
condensation in a flue gas condensing heat exchanger was
developed using MATLAB. Governing equations based on
mass and energy balances for the system were derived to
predict variables such as flue gas exit temperature, cooling
water outlet temperature, mole fraction and condensation rates
of water and sulfuric acid vapors. The equations were solved
using an iterative solution technique with calculations of heat
and mass transfer coefficients and physical properties.
Forklift Classes Overview by Intella PartsIntella Parts
Discover the different forklift classes and their specific applications. Learn how to choose the right forklift for your needs to ensure safety, efficiency, and compliance in your operations.
For more technical information, visit our website https://intellaparts.com
Welcome to WIPAC Monthly the magazine brought to you by the LinkedIn Group Water Industry Process Automation & Control.
In this month's edition, along with this month's industry news to celebrate the 13 years since the group was created we have articles including
A case study of the used of Advanced Process Control at the Wastewater Treatment works at Lleida in Spain
A look back on an article on smart wastewater networks in order to see how the industry has measured up in the interim around the adoption of Digital Transformation in the Water Industry.
Hybrid optimization of pumped hydro system and solar- Engr. Abdul-Azeez.pdffxintegritypublishin
Advancements in technology unveil a myriad of electrical and electronic breakthroughs geared towards efficiently harnessing limited resources to meet human energy demands. The optimization of hybrid solar PV panels and pumped hydro energy supply systems plays a pivotal role in utilizing natural resources effectively. This initiative not only benefits humanity but also fosters environmental sustainability. The study investigated the design optimization of these hybrid systems, focusing on understanding solar radiation patterns, identifying geographical influences on solar radiation, formulating a mathematical model for system optimization, and determining the optimal configuration of PV panels and pumped hydro storage. Through a comparative analysis approach and eight weeks of data collection, the study addressed key research questions related to solar radiation patterns and optimal system design. The findings highlighted regions with heightened solar radiation levels, showcasing substantial potential for power generation and emphasizing the system's efficiency. Optimizing system design significantly boosted power generation, promoted renewable energy utilization, and enhanced energy storage capacity. The study underscored the benefits of optimizing hybrid solar PV panels and pumped hydro energy supply systems for sustainable energy usage. Optimizing the design of solar PV panels and pumped hydro energy supply systems as examined across diverse climatic conditions in a developing country, not only enhances power generation but also improves the integration of renewable energy sources and boosts energy storage capacities, particularly beneficial for less economically prosperous regions. Additionally, the study provides valuable insights for advancing energy research in economically viable areas. Recommendations included conducting site-specific assessments, utilizing advanced modeling tools, implementing regular maintenance protocols, and enhancing communication among system components.
6. Catalytic Cracking
6/1/2021
6
SCE 4106: Fundamentals of Petroleum Processing
Originally cracking was accomplished thermally but the catalytic process
has almost completely replaced thermal cracking because more gasoline
having a higher octane and Less heavy fuel oils and light gases are
produced;
Typically cracking involves the thermal or catalytic decomposition of
petroleum fractions having huge quantities of higher molecular weight
compounds;
In catalytic crackers, the action of heat is reinforced by use of a catalyst.
Catalytic cracking ; is the most important and widely used refinery process
for converting heavy oils into more valuable gasoline and lighter products;
7. Catalytic Cracking
6/1/2021
7
SCE 4106: Fundamentals of Petroleum Processing
Since heat is required,
typically cracking reactions
are carried out in furnaces
that are supplied with either
fuel oil or fuel gas or natural
gas or electricity as heat
source;
The light gases produced by
catalytic cracking contain
more olefins than those
produced by thermal
cracking.
Thermal Versus Catalytic Cracking Yields on Similar Topped Crude
Feed
8. Catalytic Cracking
6/4/2021
8
SCE 4106: Fundamentals of Petroleum Processing
The cracking process produces carbon (coke) which remains on the
catalyst particle and rapidly lowers its activity;
To maintain catalyst activity at a useful level, it is necessary to regenerate
the catalyst by burning off this coke with air. As a result, the catalyst is
continuously moved from reactor to regenerator and back to reactor;
o The cracking reaction is endothermic and the regeneration reaction
exothermic.
The catalytic-cracking processes in use today can all be classified as
either moving-bed;
i. Thermafor catalytic cracking process, TCC or .
ii. Fluidized-bed units (fluid catalytic cracker (FCC)).
9. Catalytic Cracking
6/1/2021
9
FCC process employs a catalyst in
the form of very fine particles (70
µm) which fluidise when aerated with
vapour;
FCCU 35%
Reformer 30%
Alkylation 20%
Isomerization 15%
SCE 4106: Fundamentals of Petroleum Processing
Most modern units now in operation use a fluid catalytic cracking (FCCU)
process, in which the feed is vaporised and makes the catalyst behave as
a fluid;
FCC is “heart” of a modern refinery. Nearly every major fuels refinery has
an FCCU;
Contributes the highest volume to the
gasoline pool (usually between 35%-
40%);
10. Catalytic Cracking
6/1/2021
10
Feedstock
SCE 4106: Fundamentals of Petroleum Processing
FCC Processes primarily gas oils i.e (both atmospheric and vacuum
coker gasoil) using catalysts to crack the carbon-carbon bonds;
o Cracking lowers the average molecular weight & produces higher yields of
fuel products.
Attractive feed for catalytic cracking should have the following
characteristics:
i. Small concentrations of contaminants
o Poisons the catalyst
ii. Small concentrations of heavy aromatics
o Cracks & deposit coke on catalyst
Products may be further alkylated to improve gasoline anti knock
properties;
11. Catalytic Cracking
6/4/2021
11
Feed not often used include:
i. Visbreaker gas oils
o Contains aromatics
ii. Delayed coker gas oils
o Contains aromatics, olefins, & sulfur
iii. Vacuum resides
o High aromatics; could be diluted with gas oils
Feeds normally limited to CCR(continuous catalyst regeneration) of
approx. 3-7 wt.% (why?);
SCE 4106: Fundamentals of Petroleum Processing
Feedstock
12. Catalytic Cracking
6/1/2021
12
Primary goal of FCC is to make gasoline(“Cat gasoline”) & diesel and
o Minimize the production of heavy fuel oil
Coke production small but very important
o Burned in regenerator & provides heat for process
Light ends contain large amounts of olefins
o Good for petrochemical feedstock
o Can recover chemical grade propylene & ethylene
o Propylene, butylene, & C5 olefins can be alkylated for higher yields of
high- octane gasoline
SCE 4106: Fundamentals of Petroleum Processing
Products from the Catalytic Cracker
13. Catalytic Cracking
5/27/2021
13
Small amount of kerosene or jet fuel
o High sulphur content
Catalytic diesel fraction
o Low centane number because of aromatics
o Lowers quality of diesel pool because of low cetane number & high
concentrations of sulphur
Bottoms
o Contains sulphur, small ring & polynuclear aromatics, & catalyst fines
SCE 4106: Fundamentals of Petroleum Processing
Products from the Catalytic Cracker
14. Catalytic Cracking
6/1/2021
14
SCE 4106: Fundamentals of Petroleum Processing
Cracking Reactions
Cracking facilitates initiation, propagation and termination reactions
amongst the hydrocarbon themselves;
The primary reactions can be represented as follows:
o Paraffin → paraffin + olefin
o Alkyl naphthene → naphthene +olefin
o Alkyl aromatic → aromatic +olefin
Using paraffin cracking mechanism: Eg. n-Octane(where R =
CH3CH2CH2CH2CH2-) , the following catalytic reactions steps take
place:
15. Catalytic Cracking
6/1/2021
15
SCE 4106: Fundamentals of Petroleum Processing
Cracking Reactions
Step 1: Mild thermal cracking initiation reaction;
Step 2: Proton shift;
Carbonium ions are formed
initially by a small amount of
thermal cracking of n-
paraffins to form olefins;
These olefins add a proton
from the catalyst to form
large carbonium ions which
decompose to form small
carbonium ions and olefins;
16. Catalytic Cracking
6/1/2021
16
SCE 4106: Fundamentals of Petroleum Processing
Cracking Reactions
Step 3: Beta scission;
Step 4: Rearrangement toward more stable structure. The order of Carbonium ion
stability is tertiary > secondary> primary;
Step 5: Hydrogen ion transfer.
Large carbonium ion decomposes to form
small carbonium ions and olefins
The small carbonium ions propagate
the chain reaction by transferring a
hydrogen ion from a n-paraffin to form
a small paraffin molecule and a new
large carbonium ion.
Thus another large carbonium ion is
formed and the chain is ready to repeat
itself.
17. Catalytic Cracking
6/1/2021
17
Commercial cracking catalysts can be divided into three classes:
1) acid-treated natural aluminosilicates;
2) amorphous synthetic silica-alumina combinations;
3) crystalline synthetic silica-alumina catalysts called zeolites or
molecular sieves;
Most catalysts used in commercial units today are either class 3 or
mixtures of classes 2 and 3 catalysts;
The advantages of the zeolite catalysts over the natural and synthetic
amorphous catalysts are:
SCE 4106: Fundamentals of Petroleum Processing
Cracking Catalyst
18. Catalytic Cracking
6/1/2021
18
The advantages of the zeolite catalysts over the natural and synthetic
amorphous catalysts are:
i. Higher gasoline yields at a given conversion
ii. Higher activity(permits short residence time cracking )
iii. Production of gasolines containing a larger percentage of paraffinic
and aromatic hydrocarbons
iv. Lower coke yield
v. Increased iso-butane Production
vi. Ability to go to higher conversions per pass without over cracking
SCE 4106: Fundamentals of Petroleum Processing
Cracking Catalyst
19. Catalytic Cracking
6/1/2021
19
SCE 4106: Fundamentals of Petroleum Processing
Cracking Catalyst
Comparison of
Amorphous and Zeolite
Catalysts:
Y Zeolite Types in
Catalyst:
20. Catalytic Cracking
6/4/2021
20
Feed is heated (260-425 oC) by
heat exchange/furnace and
injected into the reactor where it
meets hot catalyst;
The cracking reactions take place
on the catalyst as it flows up the
riser;
SCE 4106: Fundamentals of Petroleum Processing
To prevent “over cracking” which produces excessive light ends at the
expense of gasoline yield, the contact time between the oil and catalyst
is minimized (Riser contact times in the order of 250 ms);
Catalytic Cracking Process
21. Catalytic Cracking
6/1/2021
21
Flue gas leaving the regenerator contains a
large quantity of carbon monoxide which is
burned to carbon dioxide in a CO furnace to
recover the available fuel energy;
SCE 4106: Fundamentals of Petroleum Processing
At the top of the riser, the catalyst and product
are separated using cyclone separators;
By this stage the catalyst is covered with coke
and has lost most of its activity;
Stripper removes hydrocarbons from catalyst by
steam injection;
Catalytic Cracking Process
22. Catalytic Cracking
6/1/2021
22
Objective is to remove carbon deposits &
restore the activity of the catalyst to something
approaching its fresh state;
SCE 4106: Fundamentals of Petroleum Processing
The spent catalyst is sent to a regenerator where the coke is burned off in
air;
Catalytic Cracking Process
Un-regenerated (spent) catalyst flows down
through a standpipe & lifted into regenerator
dense bed;
Regenerated catalyst overflows and flows down
through a standpipe to be lifted to the reactor by
steam & fresh feed.
23. Catalytic Cracking
6/1/2021
23
1) Increasing reactor temperature increases conversion
o Catalytic cracking is an endothermic reaction
o Heat to the reactor is controlled by: catalyst circulation rate,
regenerated catalyst temperature, & feed preheat
o Increasing feed preheat reduces the need for catalyst circulation for
the same reactor temperature
2) Catalyst/Oil ratio is a primary variable controlled by changing catalyst
circulation rate
o Increasing catalyst/oil ratio increases conversion (why?)
o Raising catalyst circulation also increases catalytic cracking activity &
increases reactor temperature
SCE 4106: Fundamentals of Petroleum Processing
Catalytic Cracking Process variables
24. Catalytic Cracking
6/1/2021
24
3) Increasing catalyst activity increases conversion
o Activity is decreased by coke deposition and deposition of heavy
metals
SCE 4106: Fundamentals of Petroleum Processing
Catalytic Cracking Process variables
4) Higher pressures generally do not affect conversion but do increase
coke production
5) Increasing space velocity decreases activity & conversion
o Increasing cat/oil residence time:
6) Increasing cat/oil residence time:
o Decreases catalyst activity
o Increases conversion, vapour velocity, coke and metal deposition on
the catalyst
o Gasoline yield increases initially and then decreases
26. Reforming
5/27/2021
26
Catalytic reforming is a process whereby light petroleum distillates
(naphthas) are contacted with a platinum-containing catalyst at elevated
temperatures and hydrogen pressures for the purpose of raising the
octane number of the hydrocarbon feed stream;
The low octane, paraffin-rich naphtha feed is converted to a high-octane
liquid product (reformate) that is rich in aromatic compounds;
Reforming Improve the octane of gasolines rather than yield;
In fact yield decreases due to hydrocracking reactions which take place in
the reforming operation;
SCE 4106: Fundamentals of Petroleum Processing
27. Reforming
6/1/2021
27
The typical feedstock to catalytic reformers are:
a) heavy straight-run (HSR) gasolines and
naphthas [180–375°F (82–190°C)] and
b) heavy hydrocracker naphthas;
SCE 4106: Fundamentals of Petroleum Processing
Feedstock
Naphtha feedstock to reformers typically contain
Paraffins, Olefins, Naphthenes, and Aromatics
(PONA) with 6–12 carbon atoms;
Feed naphthas often hydrotreated to remove
metals, olefins, sulphur, and nitrogen, prior to
being fed to a reforming unit;
28. Reforming
6/1/2021
28
Catalyst used in during reforming is noble metal (platinum) & very
sensitive to sulphur & nitrogen degradation;
o Feed stocks is often hydrotreated for sulphur removal,
o Control of chloride & water also important,
SCE 4106: Fundamentals of Petroleum Processing
Choice of Feedstock
Reforming is not appropriate for Gas oil streams
o These tend to easily hydrocrack & deposit coke on the reforming
catalyst
Reforming is best applied to naphtha feeds without sulphur;
o However, not catalytic cracker naphtha,
Because it contains olefins & aromatics,
o And not delayed coking naphtha
Because it contains high levels of sulphur, olefins, & aromatics
29. Reforming
5/27/2021
29
Catalytic reformer contributes the second highest volume to the gasoline
pool;
Reformate is desirable
component for gasoline due to :
i. High octane number,
ii. low vapour pressure,
iii. very low sulphur levels &
iv. low olefins concentration
Almost every refinery in the
world has a reformer
SCE 4106: Fundamentals of Petroleum Processing
30. Reforming
6/1/2021
30
Desirable reactions in a catalytic reformer all lead to the formation of
aromatics and isoparaffins as follows:
i. Paraffins are isomerized and to some extent converted to Naphthenes;
o The Naphthenes are subsequently converted to aromatics;
ii. Olefins are saturated (hydrogenated)to form paraffins which then react
as in (i) above ;
iii. Naphthenes are converted to aromatics;
iv. Aromatics are left essentially unchanged;
SCE 4106: Fundamentals of Petroleum Processing
Reactions
31. Reforming
5/27/2021
31
There are four major reactions that take place during reforming:
i. Dehydrogenation of naphthenes to aromatics,
ii. Dehydrocyclization of paraffins to aromatics,
iii. Isomerization, and
iv. Hydrocracking,
i. Dehydrogenation of Naphthenes
Produces an aromatic from a Naphthene;
The reaction is highly endothermic (favoured by high reaction
temperature and low pressure;
Naphthene Aromatic
SCE 4106: Fundamentals of Petroleum Processing
Reactions (cont…)
32. Reforming
6/1/2021
32
ii. Isomerization of Paraffins and Naphthenes:
The reaction involves ring re-arrangement, and thus ring opening to form
paraffin is possible;
SCE 4106: Fundamentals of Petroleum Processing
Reactions (cont…)
The paraffin isomerization reaction occurs rapidly at commercial
operating temperatures;
Isomerization reactions are promoted by the acid function of the catalyst;
33. Reforming
5/27/2021
33
iii. Dehydrocyclization of Paraffins:
The most-difficult reforming reaction to promote is the
dehydrocyclization of paraffins;
This reaction consists of molecular rearrangement of paraffin to a
naphthene;
Paraffin cyclization becomes easier with increasing molecular weight of
the paraffin because the probability of ring formation increases;
Dehydrocyclization is favoured by low pressure and high temperature
and requires both the metal and acid functions of the catalyst;
SCE 4106: Fundamentals of Petroleum Processing
Reactions (cont…)
34. Reforming
6/4/2021
34
Reactions
iv. Hydrocracking
SCE 4106: Fundamentals of Petroleum Processing
Paraffin hydrocracking is favoured by high temperature and high
pressure;
Relatively slow reaction (so it occurs in the last section of the reactor);
Hydrogen is consumed.
v. Dealkylation
Dealkylation of aromatics includes both making the alkyl group (a side
chain on the aromatic ring) smaller and removing the alkyl group
completely;
35. Reforming
5/27/2021
35
iv. Dealkylation (cont…):
Examples of dealkylation reactions include:
i. conversion of ethylbenzene to toluene and
ii. converting toluene to benzene, respectively;
if the alkyl side chain is large enough, the reaction is similar to
paraffin cracking;
Dealkylation is favoured by high temperature and high pressure;
NOTE: The last two reactions; dealkylation and hydrocracking are
undesirable reaction during reforming;
SCE 4106: Fundamentals of Petroleum Processing
Reactions (cont…)
37. Alkylation
6/1/2021
37
Purpose of Alkylation:
o To make high octane gasoline from
materials that are too light;
A major constituent of alkylate is 2,2,4-
trimethyl pentane ; which is defined as 100
on the octane scale;
SCE 4106: Fundamentals of Petroleum Processing
Motor fuel alkylation in the petroleum processing industry refers to the
acid catalysed conversion of C3-C5 olefins with alkyl group( preferably
isobutene) into highly branched C5-C12 isoparaffins collectively called
alkylate;
39. Alkylation
5/27/2021
39
In the 1920s & 1930s gasoline octane was improved by:
o Tetra Ethyl Lead in Straight Run Gasoline,TEL;
o Thermal reforming of naphtha;
o Thermal polymerization of Olefinic light ends;
alkylation of olefins was later developed in early 1940s to improve the
octane of aviation gasoline;
o Vladimir Ipatieff had discovered aluminium chloride Catalysis in 1932;
Catalytic cracking significantly increased the production of light ends
which formed feedstock for alkylation unit;
High concentration of the C3, C4, & C5 isomers, both olefinic & paraffinic;
led to development of both catalytic polymerization & alkylation;
SCE 4106: Fundamentals of Petroleum Processing
40. Sulphuric Acid Alkylation
6/1/2021
40
A group of major refiners & contractors consisting of Anglo-Iranian Oil, Humble
Oil & Refining, Shell Development, Standard Oil Development, & the Texas
Company developed process with sulphuric acid as the catalyst;
SCE 4106: Fundamentals of Petroleum Processing
The first alkylation unit was placed on stream at the Humble Baytown Refinery
in 1938;
Many alkylation plants were built at the same time as the catalytic cracking
units;
o Operated during World War II for aviation gasoline production.
Sulphuric acid alkylation required access to acid regeneration on a large scale;
o Most sulphuric acid alkylation plants were located on deep water for barge
transport of spent acid to regeneration at acid plants & return of fresh acid;
41. Hydrofluoric Acid (HF) Alkylation
6/1/2021
41
Later Phillips Petroleum & UOP developed a process using hydrofluoric acid as
a catalyst
o HF could be readily regenerated in alkylation plant facilities;
o No need to transport catalyst in large quantities for regeneration;
Feed Stocks
Olefins and isobutane are used as alkylation unit feedstock;
SCE 4106: Fundamentals of Petroleum Processing
Butenes (Butylene) and propene (propylene);are common olefins used, but
pentenes (amylenes) are included in some cases.
Butylene is the preferred olefin since it produces the highest octane number &
yields; Iso-butane & iso-pentane can be reacted with the olefin;
Iso-pentane not usually used since it is a good gasoline blend stock (high
octane number & low RVP):
42. Alkylation Products
5/27/2021
42
The product streams leaving an alkylation unit are:
o LPG grade propane liquid
o Normal butane liquid
o C5+ alkylate gasoline
o Tar
Alkylate gasoline is the most desirable product for high performance
automotive fuels
o Very high octane index (R+M)/2 of 95
o Low vapour pressure
Essentially no olefins, benzene or aromatics are produced from
alkylation;
SCE 4106: Fundamentals of Petroleum Processing
43. Process Chemistry
6/2/2021
43
Propylene, butylene, & pentenes
are olefins used (butylene most
preferred)
o High octane isooctane alkylate
produced;
o Lower reactant consumption
Acid catalyzed alkylation combines isoparaffins & olefins to form alkylate,
highly branched alkanes;
The reaction is carried out in the liquid phase with an acid/reactant
emulsion maintained at moderate temperatures and high pressure;
SCE 4106: Fundamentals of Petroleum Processing
44. Process Chemistry(cont…)
5/27/2021
44
The reaction is carried out using acid catalyst at low temperature and
high enough pressure to keep the hydrocarbon in the liquid state;
The quality of the product depends on the olefin feedstock i.e Isobutylene
> butenes > propene> pentene;
High isoparaffin/Olefin ratios (4:1 to 15:1) are used to minimize
polymerization and to increase product octane;
Efficient agitation (thorough mixing)to promote contact between the acid
and hydrocarbon phases is essential to high product quality and yields;
SCE 4106: Fundamentals of Petroleum Processing
45. Primary Reactions
5/27/2021
45
The principal reactions which occur during alkylation are the
combinations of olefins with iso-paraffins as follows;
OR
SCE 4106: Fundamentals of Petroleum Processing
46. Choosing between HF and H2SO4 systems
5/27/2021
46
HF process involves both low capital and total operating costs are less
compared to H2SO4 process because of the following reasons:
o Smaller, simpler reactor design;
o Use cooling water not refrigeration;
o Smaller settler devices needed for emulsion;
o Essentially complete regeneration of HF, no disposal of spent acids;
o Flexibility of operation regarding temperature and ratio of isobutane
to olefin;
SCE 4106: Fundamentals of Petroleum Processing
47. Choosing between HF and H2SO4 systems
5/27/2021
47
H2SO4 processes counter the above arguments for HF processes with
the following:
o HF require additional equipment (HF stripper tower, HF
regeneration tower, etc.) to recover or neutralize HF in various
streams, while H2SO4, the entire effluent hydrocarbon stream is
neutralized.
o Equipment is required to dry the feed streams to a few ppm water
in HF processes which is not required for H2SO4 processes.
o HF can form a toxic, ground-hugging vapour cloud (additives can
reduce volatility).
SCE 4106: Fundamentals of Petroleum Processing
48. Process variables and their effects
6/2/2021
48
1. Type of Olefin
SCE 4106: Fundamentals of Petroleum Processing
Propylene is worse
Octane numbers are low (89-92 RON)
Propylene & acid consumption are high
Butylene is preferred
Produces the highest isooctane
o Resulting Research Octane Numbers of 93-95 (with isobutane)
o RON and MON are about equal for alkylate (sensitivity of the alkylate
is very low)
Amounts of butylene consumed per alkylate produced is the lowest
Pentene results are mixed; Side reactions frequent.
49. Process variables and their effects
6/2/2021
49
3. Isobutane/Olefin Injection & Mixing
This is more relevant in sulphuric acid systems
Provide optimal reaction conditions for the very fast reaction
Inject olefin feedstock in incremental fashion to increase
isobutane/olefin ratios;
Newer plants have multi-injection & vigorous mixing systems.
SCE 4106: Fundamentals of Petroleum Processing
2. Isobutane concentration
Excess isobutene required;
High i-C4/olefin ratio increases octane number and yield, reduces side
reactions and acid consumption
Olefins need to be surrounded by isobutene exposed to acid –if not
,olefins will polymerise instead of alkylate
50. Process variables and their effects
6/2/2021
50
SCE 4106: Fundamentals of Petroleum Processing
4. Reaction Temperature
Temperature is the most noticeable variable in both reaction systems (HF
&H2SO4).
Reaction temperature has a greater effect in sulphuric acid processes than
those using HF acid;
Therefore sulfuric acid systems run at 45 °F (max: 70 oF; min: 30 oF;
above 70 oF, significant polymerization occurs);
In sulphuric acid system, at low temperature, acid viscosity increases
thus good of the reactants and subsequent separation of emulsion
becomes difficult.
However, in HF systems increasing temperature reduces octane number;
HF systems run at 95oF (increasing temperature from 60 to 125oF
degrades the alkylate quality about three octane)
51. Process variables and their effects
6/2/2021
51
Acid strength has varying effects on alkylate quality depending on the
effectiveness of Reactor mixing and the water content of the acid;
SCE 4106: Fundamentals of Petroleum Processing
5. Acid Type & Strength
The water concentration in the acid lowers its catalytic activity about
3 to 5 times as much as hydrocarbon diluents, thus an 88% acid
containing 5% water is a much less effective catalyst than the same
strength acid containing 2% water.
In sulfuric acid alkylation, the best quality and highest yields are obtained
with acid strengths of 93 to 95% by weight of acid, 1 to 2% water and the
remainder hydrocarbon diluents.
Increasing acid strength from 89 to 93% increases alkylate quality by 1-2
octane numbers;
52. Process variables and their effects
6/2/2021
52
The poorer the mixing in a reactor, the higher the acid strength
necessary to keep acid dilution down.
In hydrofluoric acid alkylation the highest octane number alkylate is
attained in the 86 to 90% by weight acidity range. Commercial operations
usually have acid concentrations between 83 and 92% hydrofluoric acid
and contain less than 1% water.
Generally only strong acids can catalyse the alkylation reaction but
weaker acids can cause polymerization to take place;
SCE 4106: Fundamentals of Petroleum Processing
5. Acid Type & Strength