This document discusses alternative water supply technologies for areas of Bangladesh where conventional shallow and deep tube wells are not suitable due to high salinity in groundwater. It describes several alternative technologies including shallow and very shallow shrouded tube wells, deep tube wells, dug wells, pond sand filters, household filters, infiltration galleries, and rainwater harvesting. For each technology, it provides details on how it works and its advantages and limitations. The document is authored by Priodeep Chowdhury, a lecturer in the Department of Civil and Environmental Engineering at Uttara University.
The characteristics, quantities, volume and composition of solid waste generated may differ from one country to another and between urban and rural areas.
It depends mainly upon the customs, climate, living conditions and economic standard of the area. As a consequence, if solid waste management is to be accomplished in an efficient and orderly manner, the fundamental aspects and relationships involved must be identified, adjusted for uniformity of data, and understood clearly. This section deals about :Solid Waste Generation ; Solid Waste Handling, Storage and Processing at the Source.
The characteristics, quantities, volume and composition of solid waste generated may differ from one country to another and between urban and rural areas.
It depends mainly upon the customs, climate, living conditions and economic standard of the area. As a consequence, if solid waste management is to be accomplished in an efficient and orderly manner, the fundamental aspects and relationships involved must be identified, adjusted for uniformity of data, and understood clearly. This section deals about :Solid Waste Generation ; Solid Waste Handling, Storage and Processing at the Source.
Key elelments, Environmental considerations- Construction Projects,. Purpose and application
2. Pre-construction planning and design
3. Environmental management plan
4. Land disturbance
5. Noise and vibration
6. Waste minimization
7. Contaminated material and wastes
8. Other environmental issues
9. Inspections, monitoring and audits
The type of handpump technology suitable for a particular area depends on the groundwater level, water quality and hydrogeological conditions. There are some areas like the costal belt in the southern part of Bangladesh, where the conventional shallow and deep tubewlls technologies are not successful due to the high salinity. Alternative water supply options are needed for those areas.
EIA for Major development projects - Mining projectsJenson Samraj
EIA is a decision making tool for developmental projects (Mining, construction of dams).
It will have environmental implication in changing the variables such as quality of air, ground water, soil in that area.
The purpose of assessment is to ensure that decision makers consider the environmental impacts to implement the project
EIA helps us to measure or predict the impact of any developmental projects on the environment. Mining refers to Extraction of valuable minerals or other geological materials from the Earth, usually from an ore body, lode, vein, seam, reef, or placer deposit.
Metals, coal, oil shale, gemstones, limestone, chalk, dimension stone, rock salt, potash, gravel, and clay. Large scale mining pollution contaminates all living organisms within the body of water
Affects environment adversely
Results in deforestation
Lecture notes of Environmental Engineering-II as per Solapur university syllabus of TE CIVIL.
Prepared by
Prof S S Jahagirdar,
Associate Professor,
N K Orchid college of Engg and Technology,
Solapur
Lecture note of Industrial Waste Treatment (Elective -III) as per syllabus of Solapur university for BE Civil
Prepared by
Prof S S Jahagirdar,
Associate Professor,
N K ORchid College of Engg and Tech,
Solapur
The Presentation includes grey water it is all wastewater that is discharged from a house, excluding black water, uses of waste water, various methods adopted to use grey water [i.g, irrigation, bathing , gardening etc.]
Key elelments, Environmental considerations- Construction Projects,. Purpose and application
2. Pre-construction planning and design
3. Environmental management plan
4. Land disturbance
5. Noise and vibration
6. Waste minimization
7. Contaminated material and wastes
8. Other environmental issues
9. Inspections, monitoring and audits
The type of handpump technology suitable for a particular area depends on the groundwater level, water quality and hydrogeological conditions. There are some areas like the costal belt in the southern part of Bangladesh, where the conventional shallow and deep tubewlls technologies are not successful due to the high salinity. Alternative water supply options are needed for those areas.
EIA for Major development projects - Mining projectsJenson Samraj
EIA is a decision making tool for developmental projects (Mining, construction of dams).
It will have environmental implication in changing the variables such as quality of air, ground water, soil in that area.
The purpose of assessment is to ensure that decision makers consider the environmental impacts to implement the project
EIA helps us to measure or predict the impact of any developmental projects on the environment. Mining refers to Extraction of valuable minerals or other geological materials from the Earth, usually from an ore body, lode, vein, seam, reef, or placer deposit.
Metals, coal, oil shale, gemstones, limestone, chalk, dimension stone, rock salt, potash, gravel, and clay. Large scale mining pollution contaminates all living organisms within the body of water
Affects environment adversely
Results in deforestation
Lecture notes of Environmental Engineering-II as per Solapur university syllabus of TE CIVIL.
Prepared by
Prof S S Jahagirdar,
Associate Professor,
N K Orchid college of Engg and Technology,
Solapur
Lecture note of Industrial Waste Treatment (Elective -III) as per syllabus of Solapur university for BE Civil
Prepared by
Prof S S Jahagirdar,
Associate Professor,
N K ORchid College of Engg and Tech,
Solapur
The Presentation includes grey water it is all wastewater that is discharged from a house, excluding black water, uses of waste water, various methods adopted to use grey water [i.g, irrigation, bathing , gardening etc.]
Water conservation by Rainwater Harvesting systems – Treatment of waste water : Physical,Chemical and
Biological methods – Root Zone treatment - Use of recycled water.
Use of Environment friendly materials, Embodied Energy of materials, Bio degradable materials. Recycling
and Reuse of steel, Aluminium and Glass.
Water to be one of four elementary substances along with Earth, Fire and Air.
Water is a precious resource and without it life is not possible on earth.
Water is a prime natural resource.
Water is essential for drinking, cooking, bathing and washing, laundering, ablution, domestic, sanitation, Agriculture and industries.
Environment management - water managementAnish Gawande
Water management is the control and movement of water resources to minimize damage to life and property and to maximize efficient beneficial use. Good water management of dams and levees reduces the risk of harm due to flooding. Irrigation water management systems make the most efficient use of limited water supplies for agriculture.
Drainage management involves water budgeting and analysis of surface and sub-surface drainage systems. Sometimes water management involves changing practices, such as groundwater withdrawal rates, or allocation of water to different purposes.
Surface and ground water sources are pinpointed, highlighting the genuine sources of public water supply. In further slides, factors governing the selection of a particular source of supply are pointed out; and finally, the necessity of water to mankind is herein.
Quality defects in TMT Bars, Possible causes and Potential Solutions.PrashantGoswami42
Maintaining high-quality standards in the production of TMT bars is crucial for ensuring structural integrity in construction. Addressing common defects through careful monitoring, standardized processes, and advanced technology can significantly improve the quality of TMT bars. Continuous training and adherence to quality control measures will also play a pivotal role in minimizing these defects.
NO1 Uk best vashikaran specialist in delhi vashikaran baba near me online vas...Amil Baba Dawood bangali
Contact with Dawood Bhai Just call on +92322-6382012 and we'll help you. We'll solve all your problems within 12 to 24 hours and with 101% guarantee and with astrology systematic. If you want to take any personal or professional advice then also you can call us on +92322-6382012 , ONLINE LOVE PROBLEM & Other all types of Daily Life Problem's.Then CALL or WHATSAPP us on +92322-6382012 and Get all these problems solutions here by Amil Baba DAWOOD BANGALI
#vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore#blackmagicformarriage #aamilbaba #kalajadu #kalailam #taweez #wazifaexpert #jadumantar #vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore #blackmagicforlove #blackmagicformarriage #aamilbaba #kalajadu #kalailam #taweez #wazifaexpert #jadumantar #vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore #Amilbabainuk #amilbabainspain #amilbabaindubai #Amilbabainnorway #amilbabainkrachi #amilbabainlahore #amilbabaingujranwalan #amilbabainislamabad
Cosmetic shop management system project report.pdfKamal Acharya
Buying new cosmetic products is difficult. It can even be scary for those who have sensitive skin and are prone to skin trouble. The information needed to alleviate this problem is on the back of each product, but it's thought to interpret those ingredient lists unless you have a background in chemistry.
Instead of buying and hoping for the best, we can use data science to help us predict which products may be good fits for us. It includes various function programs to do the above mentioned tasks.
Data file handling has been effectively used in the program.
The automated cosmetic shop management system should deal with the automation of general workflow and administration process of the shop. The main processes of the system focus on customer's request where the system is able to search the most appropriate products and deliver it to the customers. It should help the employees to quickly identify the list of cosmetic product that have reached the minimum quantity and also keep a track of expired date for each cosmetic product. It should help the employees to find the rack number in which the product is placed.It is also Faster and more efficient way.
CFD Simulation of By-pass Flow in a HRSG module by R&R Consult.pptxR&R Consult
CFD analysis is incredibly effective at solving mysteries and improving the performance of complex systems!
Here's a great example: At a large natural gas-fired power plant, where they use waste heat to generate steam and energy, they were puzzled that their boiler wasn't producing as much steam as expected.
R&R and Tetra Engineering Group Inc. were asked to solve the issue with reduced steam production.
An inspection had shown that a significant amount of hot flue gas was bypassing the boiler tubes, where the heat was supposed to be transferred.
R&R Consult conducted a CFD analysis, which revealed that 6.3% of the flue gas was bypassing the boiler tubes without transferring heat. The analysis also showed that the flue gas was instead being directed along the sides of the boiler and between the modules that were supposed to capture the heat. This was the cause of the reduced performance.
Based on our results, Tetra Engineering installed covering plates to reduce the bypass flow. This improved the boiler's performance and increased electricity production.
It is always satisfying when we can help solve complex challenges like this. Do your systems also need a check-up or optimization? Give us a call!
Work done in cooperation with James Malloy and David Moelling from Tetra Engineering.
More examples of our work https://www.r-r-consult.dk/en/cases-en/
Immunizing Image Classifiers Against Localized Adversary Attacksgerogepatton
This paper addresses the vulnerability of deep learning models, particularly convolutional neural networks
(CNN)s, to adversarial attacks and presents a proactive training technique designed to counter them. We
introduce a novel volumization algorithm, which transforms 2D images into 3D volumetric representations.
When combined with 3D convolution and deep curriculum learning optimization (CLO), itsignificantly improves
the immunity of models against localized universal attacks by up to 40%. We evaluate our proposed approach
using contemporary CNN architectures and the modified Canadian Institute for Advanced Research (CIFAR-10
and CIFAR-100) and ImageNet Large Scale Visual Recognition Challenge (ILSVRC12) datasets, showcasing
accuracy improvements over previous techniques. The results indicate that the combination of the volumetric
input and curriculum learning holds significant promise for mitigating adversarial attacks without necessitating
adversary training.
Final project report on grocery store management system..pdfKamal Acharya
In today’s fast-changing business environment, it’s extremely important to be able to respond to client needs in the most effective and timely manner. If your customers wish to see your business online and have instant access to your products or services.
Online Grocery Store is an e-commerce website, which retails various grocery products. This project allows viewing various products available enables registered users to purchase desired products instantly using Paytm, UPI payment processor (Instant Pay) and also can place order by using Cash on Delivery (Pay Later) option. This project provides an easy access to Administrators and Managers to view orders placed using Pay Later and Instant Pay options.
In order to develop an e-commerce website, a number of Technologies must be studied and understood. These include multi-tiered architecture, server and client-side scripting techniques, implementation technologies, programming language (such as PHP, HTML, CSS, JavaScript) and MySQL relational databases. This is a project with the objective to develop a basic website where a consumer is provided with a shopping cart website and also to know about the technologies used to develop such a website.
This document will discuss each of the underlying technologies to create and implement an e- commerce website.
Event Management System Vb Net Project Report.pdfKamal Acharya
In present era, the scopes of information technology growing with a very fast .We do not see any are untouched from this industry. The scope of information technology has become wider includes: Business and industry. Household Business, Communication, Education, Entertainment, Science, Medicine, Engineering, Distance Learning, Weather Forecasting. Carrier Searching and so on.
My project named “Event Management System” is software that store and maintained all events coordinated in college. It also helpful to print related reports. My project will help to record the events coordinated by faculties with their Name, Event subject, date & details in an efficient & effective ways.
In my system we have to make a system by which a user can record all events coordinated by a particular faculty. In our proposed system some more featured are added which differs it from the existing system such as security.
Vaccine management system project report documentation..pdfKamal Acharya
The Division of Vaccine and Immunization is facing increasing difficulty monitoring vaccines and other commodities distribution once they have been distributed from the national stores. With the introduction of new vaccines, more challenges have been anticipated with this additions posing serious threat to the already over strained vaccine supply chain system in Kenya.
1. Priodeep Chowdhury; Lecturer; Dept. of CEE; Uttara University.
ALTE R N AT IV E WAT E R SU PPLY TE C H N O L O G IE S
CONTENTS
Introduction
The important alternative
water supply technologies
include:
Shallow Shrouded Tube-well
(SST) and Very Shallow
Shrouded Tube-well (VSST)
Deep Tube-well
Dug Well
Pond Sand Filters
Household Filters
Infiltration Gallery
Rainwater Harvesting
INTRODUCTION
The type of hand-pump technology suitable for a particular area depends on the groundwater
level, water quality and hydrogeological conditions.
There are some areas like the costal belt in the southern part of Bangladesh, where the
conventional shallow and deep tubewlls technologies are not successful due to the high
salinity.
Alternative water supply options are needed for those areas.
The important alternative water supply technologies include:
Shallow shrouded Tube-well (SST)
Very shallow shrouded Tube-well (VSST)
Pond sand filters
Household filters
Infiltration gallery
Solar desalination
Rainwater Harvesting
2. Priodeep Chowdhury; Lecturer; Dept. of CEE; Uttara University.
Deep Tube-well
In Bangladesh two types of deep tube-wells as shown in Figure are constructed, manually
operated small diameter tube-well similar to shallow tube-wells and large diameter power
operated tube-wells called production well.
Some areas of the coastal region of Bangladesh is very suitable for construction of deep tube-
well.
Department of Public Health Engineering has sunk a total of 81,384 deep tube-well mainly in
the coastal area to provide safe water to 8.2 million people (DPHE,2000).
The identification of areas having suitable deep aquifers and a clear understanding about the
mechanism of recharge of these aquifers are needed to develop deep tube-well based water
supply systems in Bangladesh.
Dug Well
Dug well is the oldest method of groundwater withdrawal for water supplies.
The mechanism of producing water of low arsenic and other dissolved minerals concentration
by dug wells are not fully known.
Dug wells are widely used in many countries of the world for domestic water supply.
3. Priodeep Chowdhury; Lecturer; Dept. of CEE; Uttara University.
The flow in a dug wells is actuated by lowering of water table in the well due to withdrawal of
water.
Usually no special equipment or skill is required for the construction of dug wells.
For construction by manual digging, the wells should be at least Community dug wells should
be deeper to provide larger surface area for the entry of water to meet higher water demand.
Private dug wells are less that 10m deep but dug wells for communal use are usually 20-30
meters deep.1.2 meters in diameter.
Pond Sand Filters
A prospective option for development of surface water based water supply system is the
construction of community type Slow Sand Filters (SSFs) commonly known as Pond Sand
Filters (PSFs).
Slow sand filters are installed near or on the bank of a pond, which does not dry up in the dry
season. The water from the pond is pumped by a manually operated hand tube-well to feed the
filter bed, which is raised from the ground, and the treated water is collected through tap(s).
The PSF is a low-cost technology with very high efficiency in turbidity and bacterial removal.
It has received preference as an alternative water supply system for medium size settlements
in arsenic affected areas.
4. Priodeep Chowdhury; Lecturer; Dept. of CEE; Uttara University.
Although PSF has very high bacterial removal efficiency, it may not remove 100% of the
pathogens from heavily contaminated surface water.
Fig.: Pond Sand Filter for Treatment of Surface Water
5. Priodeep Chowdhury; Lecturer; Dept. of CEE; Uttara University.
The major limitations of PSF
Operation and maintenance are difficult;
Not suitable for heavily contaminated ponds;
People complained of foul taste in pond water and many resorted to using it for cooking only;
Conflicts with fish culture;
It is difficult to find an appropriate/reserve pond for installation of PSF;
Many ponds dry up in the dry season in some parts of the country;
Secondary contamination takes place due to lack of proper maintenance.
Household Filters
Surface water containing impurities can be clarified by a pitcher filter unit or a small sand
filter at the household level. It is an old method of water purification, in rural areas of
Bangladesh.
These processes of water treatment at household level have been phased out with the
introduction of tube-wells for village water supply.
Pitcher filters are constructed by stacking a number pitchers (Kalshis), one above the other,
containing different filter media.
Raw water is poured in the top Kalshi and filtered water is collected from the bottom one.
In this process, water is mainly clarified by the mechanical straining and adsorption depending
of the type of filter media used. Small household filters can be constructed by stacking about
300-450 mm thick well graded sand on a 150-225 mm thick coarse aggregate in a cylindrical
container.
The container is filled with water and the filtered water is collected from the bottom.
Full effectiveness of the filtration process is obtained if the media remain in water all the time.
The pitcher and other small household filters cannot completely remove micro-organisms if
these are present in large numbers in raw water.
6. Priodeep Chowdhury; Lecturer; Dept. of CEE; Uttara University.
The important characteristics of household filters are:
Suitable for surface water treatment;
Remove turbidity, color and micro-
organisms;
Complete removal of pathogenic micro-
organisms is not guaranteed;
Not suitable for high-turbid water;
Difficulty in cleaning and keeping the
system operational.
Infiltration Gallery
Infiltration Galleries (IG) or wells can be constructed near perennial rivers or ponds to
collect infiltrated surface waters for all domestic purposes.
Since the water infiltrate through a layer of soil/sand, it is significantly free from suspended
impurities including microorganisms usually present in surface water.
Again, surface water being the main source of water in the gallery/well, it is free from arsenic.
If the soil is impermeable, well graded sand may be placed in between the gallery and surface
water source for rapid flow of water.
Fig.: An Infiltration Gallery by the Side of a Surface Water Source
7. Priodeep Chowdhury; Lecturer; Dept. of CEE; Uttara University.
Rainwater Harvesting
Bangladesh is a tropical country and receives heavy rainfall during the rainy season.
In the coastal districts, particularly in the offshore islands of Bangladesh, rainwater harvesting
for drinking purposes is a common practice in a limited scale for long time (Chowdhury et al,
1987).
In some areas of the coastal region with high salinity problem, about 36 percent households
have been found to practice rainwater harvesting in the rainy season for drinking purpose
(Hussain and Ziauddin, 1989).
In the present context, rainwater harvesting is being seriously considered as an alternative
option for water supply in Bangladesh in the arsenic affected areas.
Advantages and disadvantages of rainwater collection system
Advantages Disadvantages
The quality of rainwater is
comparatively good.
The system is independent and therefore
suitable for scattered settlements.
Local materials and craftsmanship can
be used in construction of rainwater
system.
No energy costs are incurred in running
the system.
Ease in maintenance by the owner/user
The initial cost may prevent a family from
installing a rainwater harvesting system.
The water availability is limited by the rainfall
intensity and available roof area.
Mineral-free rainwater has a flat taste, which
may not be liked by many.
Mineral-free water may cause nutrition
deficiencies in people who are on mineral
deficient diets.
The poorer segment of the population may not
have a roof suitable for rainwater harvesting.
8. Priodeep Chowdhury; Lecturer; Dept. of CEE; Uttara University.
WWA T E RA T E R TT R E A T M E N TR E A T M E N T
Preliminary Treatment
Preliminary treatment is any physical, chemical or mechanical process used on water before it
undergoes the main treatment process.
The purpose of preliminary treatment processes is to remove any materials which will
interfere with further treatment.
Pretreatment may include screening, pre-sedimentation, chemical addition, flow measurement,
and aeration.
Preliminary Treatment / Screens
The screens are used to remove rocks, sticks, leaves, and other debris.
Very small screens can be used to screen out algae in the water.
All objects are removed by physical size separation
Screens on the outside of intakes are often cleaned by flushing water from the treatment plant
backwards
There are two primary types of screens - bar screens and wire-mesh screens.
A bar screen is used to remove large debris. The spaces between the bars are two to four
inches wide.
A wire-mesh screen is used to remove smaller debris. The gaps are about half an inch wide.
Water must be flowing slowly in order to pass through a wire-mesh screen - velocities should
be no greater than 3.5 inches per second.
• Preliminary Treatment / Pre-sedimentation - Aeration
Preliminary Treatment / Monitoring
Flow Measurement: to adjust chemical feed rates, calculate detention times, and monitor the
amount of water being treated.
It is also monitored for a variety of characteristics including pH, turbidity, total alkalinity,
temperature, and coliform bacteria.
The pH and total alkalinity of the water will influence the amount of alkali to be added and
can also influence the flocculation conditions
The level of turbidity will influence the amount of polymer (coagulant) added to the water.
Temperature is also measured since cold water does not floc as well as warm water and
requires the addition of more polymer
9. Priodeep Chowdhury; Lecturer; Dept. of CEE; Uttara University.
Primary Sedimentation
Sedimentation is a treatment process in which the velocity of the water is lowered below the
suspension velocity and the suspended particles settle out of the water due to gravity.
The process is also known as settling or clarification
Settled solids are removed as sludge, and floating solids are removed as scum
The efficiency or performance of the process is controlled by: detention time, temperature,
tank design, and condition of the equipment.
Fig.: Simple Sedimentation Tank
Notes
sedimentation may not be necessary in low turbidity water of less than 10 NTU
In this case, coagulation and flocculation are used to produce pinpoint (very small) floc which
is removed from the water in the filters
Primary Sedimentation / Location in the Treatment Process
The most common form of sedimentation follows coagulation and flocculation and precedes
filtration.
This type of sedimentation requires chemical addition (in the coagulation/flocculation step)
and removes the resulting floc from the water.
sedimentation following coagulation/flocculation is meant to remove most of the suspended
particles in the water before the water reaches the filters,
Sedimentation at this stage in the treatment process should remove 90% of the suspended
particles from the water, including bacteria.
10. Priodeep Chowdhury; Lecturer; Dept. of CEE; Uttara University.
The purpose of sedimentation here is to decrease the concentration of suspended particles in
the water, reducing the load on the filters.
Sedimentation can also occur as part of the pretreatment process, where it is known
as presedimentation.
Types of sedimentation basins
Rectangular basins: have a variety of advantages - predictability, cost-effectiveness, and low
maintenance. In addition, rectangular basins are the least likely to short-circuit, especially if
the length is at least twice the width. A disadvantage of rectangular basins is the large amount
of land area required.
Double-deck rectangular basins: This type of basin conserves land area - has higher
operation and maintenance costs.
Square or circular sedimentation basins with horizontal flow are known as clarifiers. This
type of basin is likely to have short-circuiting problems.
Solids-contact clarifiers also known as up flow solids-contact clarifiers or up flow sludge-
blanket clarifiers combine coagulation, flocculation, and sedimentation within a single basin.
found in packaged plants and in cold climates where sedimentation must occur indoors
• Sedimentation and flotation zones
All sedimentation basins have four zones - the inlet zone, the settling zone, the sludge zone,
and the outlet zone.
In a clarifier, water typically enters the basin from the center rather than from one end and
flows out to outlets located around the edges of the basin. But the four zones can still be
found within the clarifier
Filtration
After separating most floc, the water is filtered as the final step to remove remaining suspended
particles and unsettled floc
1. Rapid sand filters
Use relatively coarse sand and other granular media to remove particles and impurities that
have been trapped in a floc through the use of flocculation chemicals-typically salts
of aluminium or iron.
Water and flocs flows through the filter medium under gravity or under pumped pressure
Water moves vertically through sand which often has a layer of activated carbon or anthracite
coal (a hard, compact variety of mineral coal).
The top layer removes organic compounds
Most particles pass through surface layers but are trapped in pore spaces or adhere to sand
particles
11. Priodeep Chowdhury; Lecturer; Dept. of CEE; Uttara University.
To clean the filter, water is passed quickly upward through the filter, opposite the normal
direction (called back flushing or backwashing)
compressed air may be blown up through the bottom of the filter to break up the compacted
filter media to aid the backwashing process
Fig.: Rapid sand filters
Rapid sand filters / Advantages and disadvantages
Advantages
Much higher flow rate than a slow sand filter;
Requires relatively small land area
Less sensitive to changes in raw water quality, e.g. turbidity
requires less quantity of sand
Disadvantages
Requires greater maintenance than a slow sand filter. For this reason, it is not usually
classed as an "appropriate technology,".
Generally ineffective against taste and odour problems.
Produces large volumes of sludge for disposal.
Requires on-going investment in costly flocculation reagents.
treatment of raw water with chemicals is essential
skilled supervision is essential
cost of maintenance is more
it cannot remove bacteria
12. Priodeep Chowdhury; Lecturer; Dept. of CEE; Uttara University.
Slow sand filters
Slow "artificial" filtration (a variation of bank filtration) to the ground, Water purification
plant
The filters are carefully constructed using graded layers of sand with the coarsest sand, along
with some gravel, at the bottom and finest sand at the top.
Drains at the base convey treated water away for disinfection
effective slow sand filter may remain in service for many weeks or even months
produces water with a very low available nutrient level and low disinfectant levels
Slow sand filters are not backwashed; they are maintained by having the top layer of sand
scraped off
A 'large-scale' form of slow sand filter is the process of bank filtration in a riverbank.
Fig.: Slow sand filters
Advantages
require little or no mechanical power, chemicals or replaceable parts,
require minimal operator training and only periodic maintenance,
Often an appropriate technology for poor and isolated areas.
simple design
13. Priodeep Chowdhury; Lecturer; Dept. of CEE; Uttara University.
Disadvantages
Due to the low filtration rate, slow sand filters require extensive land area for a large
municipal system.
Many municipal systems in grown cities installed rapid sand filters, due to increased
demand for drinking water.
Membrane filtration
Is a treatment process based on the physical separation of compounds from the water phase
with the use of a semi-permeable membrane.
Most of the membranes used are synthetic membranes made of organic polymers.
Can be divided into two categories based on the pore sizes of the membrane:
micro- and ultra filtration (MF and UF) remove colloidal substances and microorganisms
Nano-filtration and reverse osmosis (NF and RO) remove colloidal substances and microor-
ganisms but also dissolved substances like micro pollutants and ions
Micro- and ultra filtration remove substances from the water phase by a sieve mechanism
Microfiltration removes bacteria and the larger viruses (to a size of 0.05 μm).
Ultra filtration also removes bacteria, but because of the smaller pore size all the larger viruses
are removed
The removal of suspended solids of MF and UF is at least 99%.
Membrane filtration
The removal of microorganisms is referred to in log units.
A removal of one log unit corresponds to a 90% removal. The removal of 4 log units cor-
responds to a 99.99% removal.
molecular weight cut-off (MWCO) can also be used as an indication of the ability of
membranes to reject compounds
MWCO is the molecular weight of spherical molecules which are 90% rejected by the
membrane’s pores.
The unit of MWCO is Dalton (1 Dalton is the mass of one hydrogen atom = 1.66x10-27
kg)
The MWCO for MF/UF is in the range of 10,000 to 500,000 Dalton (10 to 500 kD).
Aeration
Aeration is the process of bringing water and air into close contact.
14. Priodeep Chowdhury; Lecturer; Dept. of CEE; Uttara University.
Aeration is the process to remove dissolved gases, such as carbon dioxide, hydrogen sulfide,
and to oxidize dissolved metals such as iron. It can also be used to remove volatile organic
chemicals (VOC).
It happens by:
Exposing drops or thin sheets of water to the air or
Introducing small bubbles of air and letting them rise through the water.
Aeration accomplishes the desired results by:
Sweeping or scrubbing action caused by the turbulence of water and air mixing together
Oxidizing certain metals and gases
• Aeration Efficiency
CHEMICAL SUBSTANCES AFFECTED BY AERATION
The constituents that are commonly affected by aeration are:
Volatile organic chemicals, such as benzene, found in gasoline, or trichloroethylene,
dichloroethylene, and perchloroethylene, examples of solvents are used in dry cleaning or
industrial processes.
Carbon dioxide
Hydrogen sulfide (rotten-egg odor)
Methane (flammable)
Iron (will stain clothes and fixtures)
Manganese (black stains)
Various chemicals causing taste and odor
CHEMICAL SUBSTANCES AFFECTED BY AERATION
Surface waters have a low CO2 content (0 to 2 mg/l).
Deep lake or reservoir can have high CO2 content due to the respiration of microscopic
animals and lack of abundant plant growth at the lake bottom.
Aerators remove CO2 by the physical scrubbing or sweeping action caused by turbulence.
aeration can reduce the CO2 content to 4.5 mg CO2 /l
Concentration of CO2 in groundwater is usually higher than in surface water.
Water from a deep well normally contains less than 50 mg/l, but a shallow well can have a
much higher level, up to 50 to 300 mg/l.
15. Priodeep Chowdhury; Lecturer; Dept. of CEE; Uttara University.
CARBON DIOXIDE REMOVAL
The most appropriate treatment for carbon dioxide may be aeration, addition of an alkali, or
a combination of the two
CO2 gas dissolves easily in water, resulting in carbonic acid:
H2O + CO2 <===> H2CO3
CO2 is neutralized through the addition of an alkali (basic, ionic salt), such as lime (Ca(OH)2)
or soda ash (Na2CO3).
Lime reacts with carbon dioxide, removing the carbon dioxide from the water as shown
below:
CO2 + Ca(OH)2 <===> CaCO3 + H2O
CO2 above 5 to 15 mg/l in raw water can cause three operating problems:
It increases the acidity of the water, making it corrosive by forming a “weak” acid, H2CO3.
It tends to keep iron in solution, thus making iron removal more difficult.
It reacts with lime added to soften water, causing an increase in the amount of lime needed for
the softening reaction.
Taste & Odor Removal
Aeration is effective in removing tastes and odors that are caused by volatile materials
Volatile materials (e.g Methane and hydrogen sulfide) have low boiling point and will
vaporize very easily.
Many taste and odor problems in surface water could be caused by oils and by-products that
algae produce.
Since oils are much less volatile than gases, aeration is only partially effective.
Dissolved Oxygen
Oxygen is injected into water through aeration to remove the flat taste.
The amount of oxygen that the water can hold is dependent on the temp.
The colder the water, the more oxygen the water can hold.
Water that contains excessive amounts of oxygen can become very corrosive.
Excessive oxygen can cause air binding of filters.
16. Priodeep Chowdhury; Lecturer; Dept. of CEE; Uttara University.
Types of Aerators
Aerators fall into two general categories.
• Introduce air into the water or water into the air.
• The water-to-air method is designed to produce small drops of water that fall through the
air
• The air-to-water method creates small bubbles of air that are injected into the water
stream.
• All aerators are designed to create a greater amount of contact between the air and water
to enhance the transfer of the gases.
WATER INTO AIR
Cascade Aerators
• Consists of a series of steps that the water flows over.
• Aeration is accomplished in the splash zones.
• The aeration action is similar to a flowing stream.
• Splash areas are created by placing blocks across the incline.
• Cascade aerators used to oxidize iron and to partially reduce dissolved gases.
• the oldest and most common type of aerators.
Cone Aerators
Are used primarily to oxidize iron and manganese prior to filtration.
The water pumped to the top of the cones and then allowed to cascade down through the
aerator.
17. Priodeep Chowdhury; Lecturer; Dept. of CEE; Uttara University.
Slat and Coke Aerators
Similar to the cascade and cone types.
They usually consist of three-to-five stacked trays, which have spaced wooden slats in them.
The trays are filled with fist-sized pieces of coke, rock, ceramic balls, limestone, or other
materials.
The primary purpose of the materials is provide additional surface contact area between the air
and water.