6710 130 ppt2
•
0 likes•529 views
This document discusses proper handling and storing of tiling materials and accessories. It covers potential injuries from improper lifting and handling, as well as common hazards. Some key points covered include how to safely lift materials by using proper form, getting help with heavy loads, and using handling aids. Safety is emphasized, including avoiding twisting motions and lifting above shoulder level.
Report
Share
Report
Share
Download to read offline
Recommended
6710 130 ppt4
The document discusses harmful substances in the workplace and how to handle and store tiling materials and accessories safely. It covers UK legislation regarding harmful substances including the Health and Safety at Work Act of 1974 and the COSHH Regulations of 2002. The document outlines how to identify, classify, and control risks from harmful substances through proper labeling, storage, exposure reduction methods, use of personal protective equipment, and following safe practices. The goal is to educate workers on protecting themselves and preventing workplace injuries and illnesses.
6710 130 ppt3
The document describes the kinetic method of lifting, which involves 6 stages: 1) Plan the route, 2) Assess the load, 3) Position feet comfortably apart with one forward, 4) Bend knees to lower body and keep back straight, 5) Take a full palm grip on the load, 6) Lift smoothly by straightening legs and moving feet rather than twisting. It emphasizes planning the lift, keeping a straight back and the load close, and moving feet instead of twisting to lift and carry safely.
6710 130 ppt1
This document outlines guidelines for safely handling and storing tiling materials and accessories. The presentation covers lifting materials properly to avoid injury, protecting work and stored materials from damage, shielding a client's property during work, and following manufacturers' instructions carefully. Learners will understand basic material handling, protecting work, and using manufacturers' specifications.
6710 130 ppt5
This document discusses risk assessments for handling and storing tiling materials and accessories. It defines hazards, harm, and risk, and outlines the five steps to complete a risk assessment: 1) look for hazards, 2) identify those affected and how, 3) evaluate risks and existing precautions, 4) record findings, and 5) review the assessment. Employers are legally required under the Management of Health and Safety at Work Regulations 1999 to conduct suitable and sufficient risk assessments.
6710 127 l1_powerpoint_4
This document summarizes several important pieces of UK health and safety legislation that affect construction sites, including the Construction (Design and Management) Regulations 2007, the Control of Substances Hazardous to Health (COSHH) Regulations 2002, the Health and Safety at Work Act 1974, the Lifting Operations and Lifting Equipment Regulations (LOLER) 1998, the Management of Health and Safety at Work Regulations 1999, the Provision and Use of Work Equipment Regulations (PUWER) 1998, and the Work at Height Regulations 2005. It outlines the main objectives and requirements of each piece of legislation.
Disposal
The document discusses proper waste management for construction projects. It emphasizes following environmental and health and safety regulations. When buying materials, considerations include ordering the right amount, packaging disposal, and material sourcing. When storing materials, checks should be made upon delivery and proper storage conditions followed. During site activities, waste should be recycled as much as possible on site to reduce transportation. Workers may receive training on waste disposal, management, and safety. Waste should be segregated into different skips like wood, plasterboard, and metal to allow for recycling.
Tools
The document discusses tools used for tiling walls and floors. It describes various hand tools like screw drivers and cutting knives. It also covers measuring tools like tape measures for laying out tile installations. Levelling equipment is important for finding level and plumb, including spirit levels and laser levels. Tools for shaping and cutting tiles include tile nippers, manual cutters, and water saws. Finishing tools include trowels for spreading adhesive and grout. Maintaining the right tools is important for safety, efficiency and completing tiling work to standard.
Unit 101 Level 1 Principles of building construction, information and communi...
This document discusses waste management in construction. It defines waste and different types of waste. It also discusses how to reduce waste in construction, including proper disposal and recycling of materials. Methods of managing waste on construction sites are outlined, such as using separate skips for different materials and following safety procedures for waste disposal. Enforcement of waste management regulations is discussed.
Recommended
6710 130 ppt4
The document discusses harmful substances in the workplace and how to handle and store tiling materials and accessories safely. It covers UK legislation regarding harmful substances including the Health and Safety at Work Act of 1974 and the COSHH Regulations of 2002. The document outlines how to identify, classify, and control risks from harmful substances through proper labeling, storage, exposure reduction methods, use of personal protective equipment, and following safe practices. The goal is to educate workers on protecting themselves and preventing workplace injuries and illnesses.
6710 130 ppt3
The document describes the kinetic method of lifting, which involves 6 stages: 1) Plan the route, 2) Assess the load, 3) Position feet comfortably apart with one forward, 4) Bend knees to lower body and keep back straight, 5) Take a full palm grip on the load, 6) Lift smoothly by straightening legs and moving feet rather than twisting. It emphasizes planning the lift, keeping a straight back and the load close, and moving feet instead of twisting to lift and carry safely.
6710 130 ppt1
This document outlines guidelines for safely handling and storing tiling materials and accessories. The presentation covers lifting materials properly to avoid injury, protecting work and stored materials from damage, shielding a client's property during work, and following manufacturers' instructions carefully. Learners will understand basic material handling, protecting work, and using manufacturers' specifications.
6710 130 ppt5
This document discusses risk assessments for handling and storing tiling materials and accessories. It defines hazards, harm, and risk, and outlines the five steps to complete a risk assessment: 1) look for hazards, 2) identify those affected and how, 3) evaluate risks and existing precautions, 4) record findings, and 5) review the assessment. Employers are legally required under the Management of Health and Safety at Work Regulations 1999 to conduct suitable and sufficient risk assessments.
6710 127 l1_powerpoint_4
This document summarizes several important pieces of UK health and safety legislation that affect construction sites, including the Construction (Design and Management) Regulations 2007, the Control of Substances Hazardous to Health (COSHH) Regulations 2002, the Health and Safety at Work Act 1974, the Lifting Operations and Lifting Equipment Regulations (LOLER) 1998, the Management of Health and Safety at Work Regulations 1999, the Provision and Use of Work Equipment Regulations (PUWER) 1998, and the Work at Height Regulations 2005. It outlines the main objectives and requirements of each piece of legislation.
Disposal
The document discusses proper waste management for construction projects. It emphasizes following environmental and health and safety regulations. When buying materials, considerations include ordering the right amount, packaging disposal, and material sourcing. When storing materials, checks should be made upon delivery and proper storage conditions followed. During site activities, waste should be recycled as much as possible on site to reduce transportation. Workers may receive training on waste disposal, management, and safety. Waste should be segregated into different skips like wood, plasterboard, and metal to allow for recycling.
Tools
The document discusses tools used for tiling walls and floors. It describes various hand tools like screw drivers and cutting knives. It also covers measuring tools like tape measures for laying out tile installations. Levelling equipment is important for finding level and plumb, including spirit levels and laser levels. Tools for shaping and cutting tiles include tile nippers, manual cutters, and water saws. Finishing tools include trowels for spreading adhesive and grout. Maintaining the right tools is important for safety, efficiency and completing tiling work to standard.
Unit 101 Level 1 Principles of building construction, information and communi...
This document discusses waste management in construction. It defines waste and different types of waste. It also discusses how to reduce waste in construction, including proper disposal and recycling of materials. Methods of managing waste on construction sites are outlined, such as using separate skips for different materials and following safety procedures for waste disposal. Enforcement of waste management regulations is discussed.
6710 128 power_point 1_
The document provides instructions for setting out and laying tiles on a kitchen floor. It describes establishing datum lines along focal points and width points for layout. Tilers are instructed to dry lay tiles first to measure cuts, adjust lines as needed, and ensure full tiles along lines with even spacing for cuts. The process involves first fixing full tiles along datum lines, then cutting and fixing edge tiles around obstacles before grouting.
6710 126 powerpoint_1
The document discusses risk assessment for wall and floor tiling. It defines risk assessment as identifying all hazards associated with a task and evaluating the risks. It outlines the key stages of risk assessment as identifying hazards and people at risk, evaluating risk, selecting controls, providing training, keeping records, and monitoring. It also explains how to evaluate risks based on likelihood and severity of harm and how to rate and address risks.
6710 126 powerpoint_5
The document provides instructions for measuring rooms to calculate the area needed for wall and floor tiling. It describes breaking walls down into rectangles and measuring the height and width of each rectangle. The measurements are used to calculate the area of each rectangle section and the total area of the room. Specific instructions are given for measuring around doors and other fixtures. The example provided measures a sample room and calculates the total area as 19.81 square meters.
3etry
This document discusses methods for mixing tiling materials. It describes mixing mortar by volume using gauge boxes to measure sand and cement, and mixing by weight using a weight batch mixer or dry silo mortar system. It also lists typical mortar ingredients like sand, cement, lime, and water and notes the strength of the mortar should match that of the brick or block being used.
Window task
The document provides instructions for tiling around a window. It lists the required tools which include spirit levels, measuring tapes, tile cutters, and notched trowels. The instructions describe how to use spirit levels to check that the window reveals, sill, and soffit are plumb and level. Measurements are taken and center lines are marked using pencils and chalk lines. Test cuts are made and adjusted as needed using a staff stick. Tile layout is planned and marked on the walls. Tile batons are set and plumb lines added before tiling begins, working from the window up and finishing with tile trim.
Tiling tools
This document lists and describes various tools used for tiling, including different sized notched trowels, squeegees, sponges, scrapers, snips, saws, levels, measuring devices, and power tools. It also notes that health and safety requirements should be followed for each tool used.
101 Level 1 Principles of building construction, information and communication
The document is a presentation on flat roofs that introduces learners to the topic. It defines a flat roof as having a slope of less than 10 degrees and discusses key components like roof joists. It describes the three main methods for obtaining fall on a flat roof - sloping roof joists, tapered firring pieces, and deepened joists. Common materials used for flat roof coverings include chipboard sheets, underfelt, and green mineral felt.
Unit 201: Health safety and welfare in construction
The document discusses health and safety procedures for working at heights and with electrical equipment. It covers relevant legislation, types of access equipment including ladders, mobile towers, trestles and mobile elevating work platforms. Safe methods of use are emphasized, and hazards of falls, overreaching and electrical shock are addressed. Proper planning, equipment selection and adherence to safety protocols are vital to avoiding risks when working at height or with electricity.
City & Guilds General Presentation
This gives an idea about how you can get the best out of offering City and Guilds and ILM qualifications
Superconductors And their Applications
This document discusses superconductors. It defines superconductors as materials that conduct electricity without resistance below a certain temperature, magnetic field, and current. It describes two types of superconductors - Type I, which expels all magnetic flux below a critical field, and Type II, which allows partial flux penetration between two critical fields and has a higher critical temperature. The document outlines properties of superconductors related to electricity, magnetism, and applications, noting they can carry current indefinitely, expel magnetic fields via the Meissner effect, and have uses in particle accelerators, power transmission, transportation and medical imaging.
Health, Safety and Welfare in Construction
The document discusses safety precautions for working with electrical equipment. It states that electricity can kill or severely injure people and identifies hazards such as electric shock, faults causing fires, and electricity igniting flammable materials. It provides guidance on assessing electrical hazards, using robust and protected cables/plugs for different environments, inspecting equipment for damage, avoiding overhead power lines, legal requirements, identifying voltage colors, using RCDs for 240v equipment, and properly storing and maintaining electrical tools.
Superconductivity and new superconductors
Superconductivity was discovered in 1911 by Kamerlingh Onnes who observed that the electrical resistance of mercury dropped to zero at 4.2K. Since then, major developments have included the BCS theory of superconductivity in 1957 and the discovery of high-temperature superconductors with critical temperatures over 130K. Superconductors exhibit zero resistivity and the Meissner effect of repelling magnetic fields below critical temperatures and fields due to the formation of Cooper pairs. Potential applications include efficient power transmission and magnetic levitation.
Unit 301: Principles of organising, planning and pricing construction work
The document discusses insulating materials and construction methods for insulating buildings. It aims to introduce learners to estimating for insulation materials and describes where heat is lost in homes. It explains that heating and cooling accounts for 50-70% of energy used in homes and discusses why insulating homes helps maintain indoor temperatures and reduce energy costs by creating a barrier that reduces heat transfer. Various insulating materials are described such as glass wool, rockwool, foam boards and pipe insulation that can be used in walls, floors, roofs and around pipes. Construction methods discussed include using insulation location, material selection and following building regulations to insulate against heat loss and gain.
yujskooookkth
This document discusses different types of adhesives and grouts used in tiling. It describes cement-based, polymer, and acrylic adhesives, explaining their compositions, applications, and installation methods. Cement-based grouts are also covered, along with epoxy grouts and their uses in areas with water or chemicals. Proper application techniques and safety precautions are emphasized.
Superconductors and Superconductivity
Presentation about How Superconductivity was discovered, Types and Properties of Superconductors and Applications of Superconductors.
Unit 201: Health safety and welfare in construction
The document discusses personal protective equipment (PPE) and its importance in construction. It states that PPE should be used as a last resort to protect against health and safety risks that cannot otherwise be controlled. The Personal Protective Equipment at Work Regulations 1992 require that employers provide PPE and ensure it is properly assessed, maintained, stored, used correctly and replaced when necessary. The document provides examples of common types of PPE for different parts of the body and hazards, including safety helmets, gloves, eye protection, respiratory equipment, high-visibility clothing and safety footwear. It emphasizes that the right PPE must be selected based on the hazards present and properly fitted for each individual worker.
Unit 201: Health safety and welfare in construction
The document discusses health and safety requirements for handling materials and equipment on construction sites. It covers requirements for welfare facilities as defined by the Construction Design and Management regulations (CDM), such as toilets and washing facilities. It also discusses risks from noise and proper protection, safe handling of materials through lifting techniques and aids to prevent injury, and risks of drugs and alcohol on site affecting safety. The key topics are requirements for site facilities, noise protection, safe lifting practices, and avoiding drugs and alcohol while working.
Unit 201: Health safety and welfare in construction
This document discusses health and safety procedures for construction sites, including accident reporting, emergency procedures, and hazard identification. It addresses legislation for reporting accidents, types of reportable injuries, and the importance of documenting accidents. Various hazards are outlined, such as falls, falling objects, and electricity. The document also covers risk assessments, chemical storage, safety signage, and the importance of good housekeeping and waste management. Activities are included to help identify hazards, match safety signs to their meanings, and analyze accident statistics.
101 Level 1 Principles of building construction, information and communication
This document discusses different types of foundations for buildings. It describes three main types: strip foundations, which involve digging a trench and pouring concrete; raft foundations, which distribute weight over a larger area for poor soil; and piled foundations, which are used for large, heavy buildings on poor ground. It also covers factors considered for foundations like the building's weight, use, and soil composition at the site.
101 Level 1 Principles of building construction, information and communication
This document discusses communication methods used in construction. It begins by defining communication and explaining its importance. Four main categories of communication are discussed: verbal, written/signs, electronic, and human signals. For each category, advantages and disadvantages of the methods are listed. The document concludes by describing an upcoming activity where students will experience different communication methods by working in pairs or groups at stations.
Access equipment and working platforms 4
This document discusses safety procedures for erecting and using access equipment like ladders and stepladders. It emphasizes the importance of pre-use checks to identify any faults or damage, proper lifting techniques, securing equipment properly at base and top, maintaining a safe angle, and not overreaching while working. Faulty equipment should not be used under any circumstances and must be reported if identified. Personal protective equipment appropriate for working at heights is also recommended.
Unit 115: Produce woodworking joints
This document discusses holding devices used in carpentry and joinery. It defines holding devices as tools that grip or hold items together, listing examples like vices, G-clamps, F-clamps, sash clamps, hold fasts, pliers and pincers. The document notes that clamps can damage wood by applying too much pressure, so scrap wood is often used between clamps and projects. It also provides brief descriptions of G-clamps, F-clamps, and sash clamps, and recommends storing G-clamps horizontally and sash clamps vertically. The overall aim is to introduce learners to common holding devices and their uses.
More Related Content
Viewers also liked
6710 128 power_point 1_
The document provides instructions for setting out and laying tiles on a kitchen floor. It describes establishing datum lines along focal points and width points for layout. Tilers are instructed to dry lay tiles first to measure cuts, adjust lines as needed, and ensure full tiles along lines with even spacing for cuts. The process involves first fixing full tiles along datum lines, then cutting and fixing edge tiles around obstacles before grouting.
6710 126 powerpoint_1
The document discusses risk assessment for wall and floor tiling. It defines risk assessment as identifying all hazards associated with a task and evaluating the risks. It outlines the key stages of risk assessment as identifying hazards and people at risk, evaluating risk, selecting controls, providing training, keeping records, and monitoring. It also explains how to evaluate risks based on likelihood and severity of harm and how to rate and address risks.
6710 126 powerpoint_5
The document provides instructions for measuring rooms to calculate the area needed for wall and floor tiling. It describes breaking walls down into rectangles and measuring the height and width of each rectangle. The measurements are used to calculate the area of each rectangle section and the total area of the room. Specific instructions are given for measuring around doors and other fixtures. The example provided measures a sample room and calculates the total area as 19.81 square meters.
3etry
This document discusses methods for mixing tiling materials. It describes mixing mortar by volume using gauge boxes to measure sand and cement, and mixing by weight using a weight batch mixer or dry silo mortar system. It also lists typical mortar ingredients like sand, cement, lime, and water and notes the strength of the mortar should match that of the brick or block being used.
Window task
The document provides instructions for tiling around a window. It lists the required tools which include spirit levels, measuring tapes, tile cutters, and notched trowels. The instructions describe how to use spirit levels to check that the window reveals, sill, and soffit are plumb and level. Measurements are taken and center lines are marked using pencils and chalk lines. Test cuts are made and adjusted as needed using a staff stick. Tile layout is planned and marked on the walls. Tile batons are set and plumb lines added before tiling begins, working from the window up and finishing with tile trim.
Tiling tools
This document lists and describes various tools used for tiling, including different sized notched trowels, squeegees, sponges, scrapers, snips, saws, levels, measuring devices, and power tools. It also notes that health and safety requirements should be followed for each tool used.
101 Level 1 Principles of building construction, information and communication
The document is a presentation on flat roofs that introduces learners to the topic. It defines a flat roof as having a slope of less than 10 degrees and discusses key components like roof joists. It describes the three main methods for obtaining fall on a flat roof - sloping roof joists, tapered firring pieces, and deepened joists. Common materials used for flat roof coverings include chipboard sheets, underfelt, and green mineral felt.
Unit 201: Health safety and welfare in construction
The document discusses health and safety procedures for working at heights and with electrical equipment. It covers relevant legislation, types of access equipment including ladders, mobile towers, trestles and mobile elevating work platforms. Safe methods of use are emphasized, and hazards of falls, overreaching and electrical shock are addressed. Proper planning, equipment selection and adherence to safety protocols are vital to avoiding risks when working at height or with electricity.
City & Guilds General Presentation
This gives an idea about how you can get the best out of offering City and Guilds and ILM qualifications
Superconductors And their Applications
This document discusses superconductors. It defines superconductors as materials that conduct electricity without resistance below a certain temperature, magnetic field, and current. It describes two types of superconductors - Type I, which expels all magnetic flux below a critical field, and Type II, which allows partial flux penetration between two critical fields and has a higher critical temperature. The document outlines properties of superconductors related to electricity, magnetism, and applications, noting they can carry current indefinitely, expel magnetic fields via the Meissner effect, and have uses in particle accelerators, power transmission, transportation and medical imaging.
Health, Safety and Welfare in Construction
The document discusses safety precautions for working with electrical equipment. It states that electricity can kill or severely injure people and identifies hazards such as electric shock, faults causing fires, and electricity igniting flammable materials. It provides guidance on assessing electrical hazards, using robust and protected cables/plugs for different environments, inspecting equipment for damage, avoiding overhead power lines, legal requirements, identifying voltage colors, using RCDs for 240v equipment, and properly storing and maintaining electrical tools.
Superconductivity and new superconductors
Superconductivity was discovered in 1911 by Kamerlingh Onnes who observed that the electrical resistance of mercury dropped to zero at 4.2K. Since then, major developments have included the BCS theory of superconductivity in 1957 and the discovery of high-temperature superconductors with critical temperatures over 130K. Superconductors exhibit zero resistivity and the Meissner effect of repelling magnetic fields below critical temperatures and fields due to the formation of Cooper pairs. Potential applications include efficient power transmission and magnetic levitation.
Unit 301: Principles of organising, planning and pricing construction work
The document discusses insulating materials and construction methods for insulating buildings. It aims to introduce learners to estimating for insulation materials and describes where heat is lost in homes. It explains that heating and cooling accounts for 50-70% of energy used in homes and discusses why insulating homes helps maintain indoor temperatures and reduce energy costs by creating a barrier that reduces heat transfer. Various insulating materials are described such as glass wool, rockwool, foam boards and pipe insulation that can be used in walls, floors, roofs and around pipes. Construction methods discussed include using insulation location, material selection and following building regulations to insulate against heat loss and gain.
yujskooookkth
This document discusses different types of adhesives and grouts used in tiling. It describes cement-based, polymer, and acrylic adhesives, explaining their compositions, applications, and installation methods. Cement-based grouts are also covered, along with epoxy grouts and their uses in areas with water or chemicals. Proper application techniques and safety precautions are emphasized.
Superconductors and Superconductivity
Presentation about How Superconductivity was discovered, Types and Properties of Superconductors and Applications of Superconductors.
Unit 201: Health safety and welfare in construction
The document discusses personal protective equipment (PPE) and its importance in construction. It states that PPE should be used as a last resort to protect against health and safety risks that cannot otherwise be controlled. The Personal Protective Equipment at Work Regulations 1992 require that employers provide PPE and ensure it is properly assessed, maintained, stored, used correctly and replaced when necessary. The document provides examples of common types of PPE for different parts of the body and hazards, including safety helmets, gloves, eye protection, respiratory equipment, high-visibility clothing and safety footwear. It emphasizes that the right PPE must be selected based on the hazards present and properly fitted for each individual worker.
Unit 201: Health safety and welfare in construction
The document discusses health and safety requirements for handling materials and equipment on construction sites. It covers requirements for welfare facilities as defined by the Construction Design and Management regulations (CDM), such as toilets and washing facilities. It also discusses risks from noise and proper protection, safe handling of materials through lifting techniques and aids to prevent injury, and risks of drugs and alcohol on site affecting safety. The key topics are requirements for site facilities, noise protection, safe lifting practices, and avoiding drugs and alcohol while working.
Unit 201: Health safety and welfare in construction
This document discusses health and safety procedures for construction sites, including accident reporting, emergency procedures, and hazard identification. It addresses legislation for reporting accidents, types of reportable injuries, and the importance of documenting accidents. Various hazards are outlined, such as falls, falling objects, and electricity. The document also covers risk assessments, chemical storage, safety signage, and the importance of good housekeeping and waste management. Activities are included to help identify hazards, match safety signs to their meanings, and analyze accident statistics.
101 Level 1 Principles of building construction, information and communication
This document discusses different types of foundations for buildings. It describes three main types: strip foundations, which involve digging a trench and pouring concrete; raft foundations, which distribute weight over a larger area for poor soil; and piled foundations, which are used for large, heavy buildings on poor ground. It also covers factors considered for foundations like the building's weight, use, and soil composition at the site.
101 Level 1 Principles of building construction, information and communication
This document discusses communication methods used in construction. It begins by defining communication and explaining its importance. Four main categories of communication are discussed: verbal, written/signs, electronic, and human signals. For each category, advantages and disadvantages of the methods are listed. The document concludes by describing an upcoming activity where students will experience different communication methods by working in pairs or groups at stations.
Viewers also liked (20)
101 Level 1 Principles of building construction, information and communication
101 Level 1 Principles of building construction, information and communication
Unit 201: Health safety and welfare in construction
Unit 201: Health safety and welfare in construction
Unit 301: Principles of organising, planning and pricing construction work
Unit 301: Principles of organising, planning and pricing construction work
Unit 201: Health safety and welfare in construction
Unit 201: Health safety and welfare in construction
Unit 201: Health safety and welfare in construction
Unit 201: Health safety and welfare in construction
Unit 201: Health safety and welfare in construction
Unit 201: Health safety and welfare in construction
101 Level 1 Principles of building construction, information and communication
101 Level 1 Principles of building construction, information and communication
101 Level 1 Principles of building construction, information and communication
101 Level 1 Principles of building construction, information and communication
Similar to 6710 130 ppt2
Access equipment and working platforms 4
This document discusses safety procedures for erecting and using access equipment like ladders and stepladders. It emphasizes the importance of pre-use checks to identify any faults or damage, proper lifting techniques, securing equipment properly at base and top, maintaining a safe angle, and not overreaching while working. Faulty equipment should not be used under any circumstances and must be reported if identified. Personal protective equipment appropriate for working at heights is also recommended.
Unit 115: Produce woodworking joints
This document discusses holding devices used in carpentry and joinery. It defines holding devices as tools that grip or hold items together, listing examples like vices, G-clamps, F-clamps, sash clamps, hold fasts, pliers and pincers. The document notes that clamps can damage wood by applying too much pressure, so scrap wood is often used between clamps and projects. It also provides brief descriptions of G-clamps, F-clamps, and sash clamps, and recommends storing G-clamps horizontally and sash clamps vertically. The overall aim is to introduce learners to common holding devices and their uses.
6710 127 l1_powerpoint_1
The document discusses tools used for tiling walls and floors. It describes various hand tools like screw drivers and cutting knives. It also covers measuring tools like tape measures for laying out tile installations. Levelling equipment is important for finding level and plumb, including spirit levels and laser levels. Tools for shaping and cutting tiles include tile nippers, manual cutters, and water saws. Finishing tools include trowels for spreading adhesive and grout. Maintaining the right tools is important for safety, efficiency and completing tiling work to standard.
Unit 113: Maintain and use carpentry and joinery hand tools
The document discusses hazards associated with using hand tools in carpentry and joinery. It identifies misuse and improper maintenance as the two most common hazards, which can result in tools breaking and causing injury. Personal protective equipment like safety glasses and boots should always be worn when using hand tools. Hand tools should be stored correctly in toolboxes, bags, belts or rolls when not in use to prevent damage and reduce risks of injury.
Unit 113: Maintain and use carpentry and joinery hand tools
The document discusses hazards associated with using hand tools in carpentry and joinery. It identifies misuse and improper maintenance as the two most common hazards, which can result in tools breaking and causing injury. Personal protective equipment like safety glasses and boots should always be worn when using hand tools. Hand tools should be stored correctly in toolboxes, bags, belts or rolls when not in use to prevent damage and reduce risks of injury.
Wallpapering tools and equipment
The document discusses wallpapering tools and equipment for a Level 1 Diploma in Painting and Decorating. It asks students to name wallpapering tools and identify examples, and explains why tools must be cleaned and maintained to prevent damage, rust, and rot. The document also notes tools should be stored in a dry, well-ventilated area with shelves and hooks.
6710 127 l1_powerpoint_3
The document discusses proper waste management for construction projects. It emphasizes following environmental and health and safety regulations. When buying materials, considerations include ordering the right amount, packaging disposal, and material sourcing. When storing materials, checks should be made upon delivery and proper storage conditions followed. During site activities, waste should be recycled as much as possible on site to reduce transportation. Workers may receive training on waste disposal, management, and safety. Waste should be segregated into different skips like wood, plasterboard, and metal to allow for recycling.
Tutor core 01 handle and store materials
This document provides information on proper storage of construction materials. It notes that materials should be covered, stored off the ground, and supported as needed to prevent damage from weather, theft, and deterioration over time. Specific guidance is given for storing pipes, long materials, flammables, and preventing unauthorized access and damage during storage. Proper storage methods help protect materials and costs, and prevent projects from being delayed.
D high risk activities (1)
The document discusses various high risk activities related to manual handling, working at heights, and excavations. It provides information on proper lifting techniques to prevent back injuries, fall protection measures like guardrails and harnesses, safe use of access equipment such as ladders and scaffolding, and hazards associated with excavations such as collapses and buried utilities. The employer responsibilities around risk assessment, training, and safe systems of work are also outlined.
6708 13 l1_121_presentation_2
This document outlines the preparation of background surfaces for plastering. It discusses stripping plaster by hand or machine, cleaning surfaces, and the importance of cleaning and waste disposal. It describes various hand tools like lump hammers, bolster chisels, claw hammers, and wire brushes that are used to strip plaster and prepare surfaces. Safety equipment like dust sheets and vacuums are also discussed. Proper disposal of gypsum waste is emphasized.
Introduction to using ladders 1
The document discusses safe ladder use and access equipment. It covers topics like pre-use checks, setting up ladders at the proper angle, securing ladders when in use, avoiding overhead hazards, and ensuring three points of contact are maintained. Guidelines are provided around using ladders for under 30 minutes and for light work only.
201.5 Manual Handling
This document provides an overview of safe manual handling procedures for a Level 1 Diploma in Carpentry and Joinery. It outlines the objectives to identify legislation relating to safe handling of materials and equipment, and state procedures for safe lifting and manual handling activities. The document discusses what manual handling is, why correct procedures are important for preventing injuries, and the relevant legislation regarding duties of employers and employees to assess risks and use lifting aids. It provides guidance on safe lifting techniques and approved lifting aids.
Practical Equipment for Blocklaying
The document discusses various tools and equipment used for blocklaying activities. It describes mixers for mixing mortar and concrete, wheelbarrows for transporting resources around the site, and buckets and containers for removing waste and transporting water. Other equipment mentioned includes transformers and extension leads for reducing voltage, shovels for loading mixers and moving waste, brooms for sweeping, a straight edge for transferring levels, cleaning equipment like hoses and brushes, and gloves which are required for safety.
Power point 2
This document provides information about applying floating coats to walls as part of a Level 1 Diploma in Plastering. It discusses selecting appropriate mixes and tools, preparing surfaces by fixing beads and checking for straightness, mixing plaster safely and consistently, and using tools like trowels, hawk boards, spot boards, floats, and straight edges to apply floating coats. Health and safety regulations for mixing and application are also addressed.
Unit 101, ppt 2, Principles of building, construction, information and commu...
This document discusses waste management in construction. It defines waste and different types of waste. It also discusses how to reduce waste in construction, including proper disposal and recycling of materials. Methods of managing waste on construction sites are outlined, such as using separate skips for different materials and following safety procedures for waste disposal. Enforcement of waste management regulations is also mentioned.
unit 101 ppt_2
This document discusses waste management in construction. It defines waste and different types of waste. It also discusses how to reduce waste in construction, including proper disposal and recycling of materials. Methods of managing waste on construction sites are outlined, such as using separate skips for different materials and following safety procedures for waste disposal. Enforcement of waste management regulations is also mentioned.
Construction u101 ppt_2
This document discusses waste management in construction. It defines waste and different types of waste. It also discusses how to reduce waste in construction, including proper disposal and recycling of materials. Methods of managing waste on construction sites are outlined, such as using separate skips for different materials and following safety procedures for waste disposal. Enforcement of waste management regulations is also mentioned.
Health and safety induction
This health and safety induction covers various workplace hazards and safety procedures. It discusses evacuation plans, common accident types, safety signage, hazards like working at heights and with chemicals/electricity. Proper use of ladders, scaffolds, protective equipment and incident reporting are outlined. Manual handling, fire safety and the importance of prevention are also emphasized. The goal is to educate workers and promote a safety-focused culture.
Safety During MATERIAL HANDLING, By B C Das
Do’s & Don’t and Know why material handling safety is important in your workplace, safety during storage and transport. It is sharing of knowledge. By Bimal Chandra Das / Kolkata / Bokaro
6707 l1u116 presentation_3
This document discusses a Level 1 Diploma in Painting and Decorating course focused on erecting and dismantling access equipment and working platforms. It covers the importance of inspections, components of different access equipment, potential hazards of working at heights, and examples of unsafe working platform situations. The goal is to educate painting and decorating students on safely setting up and using equipment to access work areas at elevated levels.
Similar to 6710 130 ppt2 (20)
Unit 113: Maintain and use carpentry and joinery hand tools
Unit 113: Maintain and use carpentry and joinery hand tools
Unit 113: Maintain and use carpentry and joinery hand tools
Unit 113: Maintain and use carpentry and joinery hand tools
Unit 101, ppt 2, Principles of building, construction, information and commu...
Unit 101, ppt 2, Principles of building, construction, information and commu...
More from Gordon Turner
Fundamentals walls
The document provides instructions for four tiling tasks: fixing wall tiles in a straight bond, fixing tiles in a broken bond, fixing tiles at a 45 degree angle, and general requirements for tile size. Tiles must be between 150mm x 150mm and 200mm x 200mm, and the tiling area must be at least 1.8m2. Working sketches based on 150mm x 150mm tiles are included but are not to scale. The lecturer will confirm tile sizes before each task begins.
Adhesives and grouts km 1
This document discusses different types of adhesives and grouts used in tiling. It describes cement-based, polymer, and acrylic adhesives, what they consist of, where they are used, and how they are applied. Cement-based adhesives come in powder form, polymer adhesives are pre-mixed, and acrylic adhesives are ready-to-use. Grouts also come in cement-based and epoxy varieties. Epoxy grout is used in areas with high chemical exposure. The document stresses following manufacturers' instructions for health and safety with all adhesives and grouts.
6710 126 powerpoint_4
The document discusses best practices for tile installers when initially contacting customers and conducting an in-home assessment. It recommends tile installers obtain customer contact information, ask questions about the job scope, determine how the customer was referred, schedule a time window rather than a specific time for the assessment, greet the customer professionally, avoid discussing controversial topics, take accurate measurements, and obtain necessary material details. The overall guidance is aimed at conducting the initial customer interaction efficiently and making a positive first impression.
6710 126 powerpoint_3
The document discusses the Level 1 Diploma in Wall and Floor Tiling. It covers tiling various areas beyond just bathrooms and kitchens, such as hallways, conservatories, and extensions. A wide variety of tile types are presented, and additional tiling services are described like supplying tiles and materials or tiling for new builds and renovations. The importance of developing skills, maintaining high quality work, and building a good reputation over a long career in tiling is emphasized.
6710 126 powerpoint_2
This document outlines the essential tools, equipment, and supplies needed to complete a Level 1 Diploma in Wall and Floor Tiling. It includes manual tools such as hammers, trowels, files, and spirit levels. It also lists power tools like drills, angle grinders, and tile cutters. Personal protective equipment is recommended like knee pads, safety glasses, gloves, and steel-toe boots. Additional materials mentioned are cleaning supplies, first aid kits, and consumables for jobsite comfort.
6710 128 power_point 2_
This document discusses the classification and types of grout used for tiling. It explains that grout is classified based on its composition, with C representing cementitious grout and R representing resin grout. Within these classifications are improvement characteristics added, such as reduced water absorption or increased abrasion resistance. Common grout types include normal cementitious grout, improved cementitious grout with reduced water absorption, and resin grouts.
6710 128 power_point 1_
The document discusses the classification of tile adhesives. It describes the different types of adhesive classifications (C, D, R, and S) and what each classification represents. C adhesives are cementitious, D are dispersion, R are resin, and S are deformable. Within each classification there are types that denote characteristics like fast-setting, extended open time, or reduced slip. For example, a C2FT adhesive would be an improved cementitious adhesive that is fast-setting with reduced slip. The document provides details on the various types within each adhesive classification.
6710 129 ppt2_tools and equipment
This document discusses tools and equipment used for mixing tiling materials. It describes hand tools like buckets, bucket trowels, scrapers and shovels for mixing small amounts of grout, adhesive and screed. It also mentions power tools like mixing drills, paddles and cement mixers that are used to prepare larger volumes of materials like screeds and renders. The document provides images and descriptions of each tool and its purpose in mixing different tiling compounds.
6710 129
The document discusses personal protective equipment needed for mixing tiling materials. It recommends wearing gloves to prevent skin irritation from harmful substances, goggles to prevent eye injuries from splashes and debris while mixing, and masks to prevent lung damage from breathing in particles and toxic vapors. Ear defenders and safety footwear are also advised to reduce hearing damage and protect the feet and toes. High visibility clothing and hard hats are described as essential for site safety to ensure workers can be seen and protected from falling objects.
sour
The document discusses specifications, delivery notes, manufacturers' instructions, written and oral instructions, and health and safety legislation for a Level 1 Diploma in Wall and Floor Tiling. Specifications provide written descriptions of project details and materials. Delivery notes must be checked against orders. Manufacturers' instructions specify how to properly use materials. Oral instructions should be confirmed in writing to avoid disputes. All work must comply with UK health and safety laws.
Preparing
This document discusses the importance of proper preparation before tiling walls or floors. It states that the background must be evaluated to ensure it is suitable for tiles and lists various checks that should be performed on both walls and floors. These checks include confirming the surface is plumb, flat, dry, dust-free and can support the tile type. If any issues are found, such as an unlevel floor, solutions like self-leveling compounds are provided. Proper preparation and pre-tiling checks are described as vital to allow setting out and tiling to proceed correctly.
Basic
This document provides instructions for applying grout during wall and floor tiling installations. It explains that grouting is an essential part of tiling that adds aesthetic appearance and allows for slight tile size deviations. The document outlines grout preparation steps like ensuring the adhesive is dry and joints are clear. It also details the necessary tools like grout floats and mixers and describes the grouting procedure which involves applying grout, cleaning excess from tiles, and allowing it to dry fully. Proper grout application and cleaning is emphasized for achieving uniform, smooth joints.
Measuring
The document provides instructions for measuring rooms to calculate the area needed for wall and floor tiling. It describes breaking walls down into rectangles and measuring the height and width of each rectangle. The measurements are used to calculate the area of each rectangle section and the total area of the room. Specific instructions are given for measuring around doors, windows, and fixtures.
Your First Job
The document discusses best practices for tile installers when initially contacting customers and conducting an in-home assessment. It recommends tile installers obtain customer contact information, ask questions about the job scope, determine how the customer was referred, schedule a time window rather than a specific time for the assessment, greet the customer professionally, avoid discussing controversial topics, take accurate measurements, and obtain necessary material details. The overall guidance is aimed at conducting the initial customer interaction efficiently and making a positive first impression.
More from Gordon Turner (14)
Recently uploaded
A Strategic Approach: GenAI in Education
Artificial Intelligence (AI) technologies such as Generative AI, Image Generators and Large Language Models have had a dramatic impact on teaching, learning and assessment over the past 18 months. The most immediate threat AI posed was to Academic Integrity with Higher Education Institutes (HEIs) focusing their efforts on combating the use of GenAI in assessment. Guidelines were developed for staff and students, policies put in place too. Innovative educators have forged paths in the use of Generative AI for teaching, learning and assessments leading to pockets of transformation springing up across HEIs, often with little or no top-down guidance, support or direction.
This Gasta posits a strategic approach to integrating AI into HEIs to prepare staff, students and the curriculum for an evolving world and workplace. We will highlight the advantages of working with these technologies beyond the realm of teaching, learning and assessment by considering prompt engineering skills, industry impact, curriculum changes, and the need for staff upskilling. In contrast, not engaging strategically with Generative AI poses risks, including falling behind peers, missed opportunities and failing to ensure our graduates remain employable. The rapid evolution of AI technologies necessitates a proactive and strategic approach if we are to remain relevant.
Chapter 4 - Islamic Financial Institutions in Malaysia.pptx
Chapter 4 - Islamic Financial Institutions in Malaysia.pptxMohd Adib Abd Muin, Senior Lecturer at Universiti Utara Malaysia
This slide is special for master students (MIBS & MIFB) in UUM. Also useful for readers who are interested in the topic of contemporary Islamic banking.
clinical examination of hip joint (1).pdf
described clinical examination all orthopeadic conditions .
How to Fix the Import Error in the Odoo 17
An import error occurs when a program fails to import a module or library, disrupting its execution. In languages like Python, this issue arises when the specified module cannot be found or accessed, hindering the program's functionality. Resolving import errors is crucial for maintaining smooth software operation and uninterrupted development processes.
বাংলাদেশ অর্থনৈতিক সমীক্ষা (Economic Review) ২০২৪ UJS App.pdf
বাংলাদেশের অর্থনৈতিক সমীক্ষা ২০২৪ [Bangladesh Economic Review 2024 Bangla.pdf] কম্পিউটার , ট্যাব ও স্মার্ট ফোন ভার্সন সহ সম্পূর্ণ বাংলা ই-বুক বা pdf বই " সুচিপত্র ...বুকমার্ক মেনু 🔖 ও হাইপার লিংক মেনু 📝👆 যুক্ত ..
আমাদের সবার জন্য খুব খুব গুরুত্বপূর্ণ একটি বই ..বিসিএস, ব্যাংক, ইউনিভার্সিটি ভর্তি ও যে কোন প্রতিযোগিতা মূলক পরীক্ষার জন্য এর খুব ইম্পরট্যান্ট একটি বিষয় ...তাছাড়া বাংলাদেশের সাম্প্রতিক যে কোন ডাটা বা তথ্য এই বইতে পাবেন ...
তাই একজন নাগরিক হিসাবে এই তথ্য গুলো আপনার জানা প্রয়োজন ...।
বিসিএস ও ব্যাংক এর লিখিত পরীক্ষা ...+এছাড়া মাধ্যমিক ও উচ্চমাধ্যমিকের স্টুডেন্টদের জন্য অনেক কাজে আসবে ...
Executive Directors Chat Leveraging AI for Diversity, Equity, and Inclusion
Let’s explore the intersection of technology and equity in the final session of our DEI series. Discover how AI tools, like ChatGPT, can be used to support and enhance your nonprofit's DEI initiatives. Participants will gain insights into practical AI applications and get tips for leveraging technology to advance their DEI goals.
The History of Stoke Newington Street Names
Presented at the Stoke Newington Literary Festival on 9th June 2024
www.StokeNewingtonHistory.com
ANATOMY AND BIOMECHANICS OF HIP JOINT.pdf
it describes the bony anatomy including the femoral head , acetabulum, labrum . also discusses the capsule , ligaments . muscle that act on the hip joint and the range of motion are outlined. factors affecting hip joint stability and weight transmission through the joint are summarized.
Hindi varnamala | hindi alphabet PPT.pdf
हिंदी वर्णमाला पीपीटी, hindi alphabet PPT presentation, hindi varnamala PPT, Hindi Varnamala pdf, हिंदी स्वर, हिंदी व्यंजन, sikhiye hindi varnmala, dr. mulla adam ali, hindi language and literature, hindi alphabet with drawing, hindi alphabet pdf, hindi varnamala for childrens, hindi language, hindi varnamala practice for kids, https://www.drmullaadamali.com
Natural birth techniques - Mrs.Akanksha Trivedi Rama University
Natural birth techniques - Mrs.Akanksha Trivedi Rama UniversityAkanksha trivedi rama nursing college kanpur.
Natural birth techniques are various type such as/ water birth , alexender method, hypnosis, bradley method, lamaze method etcTypes of Herbal Cosmetics its standardization.
Physiology and chemistry of skin and pigmentation, hairs, scalp, lips and nail, Cleansing cream, Lotions, Face powders, Face packs, Lipsticks, Bath products, soaps and baby product,
Preparation and standardization of the following : Tonic, Bleaches, Dentifrices and Mouth washes & Tooth Pastes, Cosmetics for Nails.
DRUGS AND ITS classification slide share
Any substance (other than food) that is used to prevent, diagnose, treat, or relieve symptoms of a
disease or abnormal condition
Your Skill Boost Masterclass: Strategies for Effective Upskilling
Your Skill Boost Masterclass: Strategies for Effective UpskillingExcellence Foundation for South Sudan
Strategies for Effective Upskilling is a presentation by Chinwendu Peace in a Your Skill Boost Masterclass organisation by the Excellence Foundation for South Sudan on 08th and 09th June 2024 from 1 PM to 3 PM on each day.How to Build a Module in Odoo 17 Using the Scaffold Method
Odoo provides an option for creating a module by using a single line command. By using this command the user can make a whole structure of a module. It is very easy for a beginner to make a module. There is no need to make each file manually. This slide will show how to create a module using the scaffold method.
Recently uploaded (20)
Chapter 4 - Islamic Financial Institutions in Malaysia.pptx
Chapter 4 - Islamic Financial Institutions in Malaysia.pptx
বাংলাদেশ অর্থনৈতিক সমীক্ষা (Economic Review) ২০২৪ UJS App.pdf
বাংলাদেশ অর্থনৈতিক সমীক্ষা (Economic Review) ২০২৪ UJS App.pdf
Executive Directors Chat Leveraging AI for Diversity, Equity, and Inclusion
Executive Directors Chat Leveraging AI for Diversity, Equity, and Inclusion
Natural birth techniques - Mrs.Akanksha Trivedi Rama University
Natural birth techniques - Mrs.Akanksha Trivedi Rama University
Film vocab for eal 3 students: Australia the movie
Film vocab for eal 3 students: Australia the movie
Your Skill Boost Masterclass: Strategies for Effective Upskilling
Your Skill Boost Masterclass: Strategies for Effective Upskilling
How to Build a Module in Odoo 17 Using the Scaffold Method
How to Build a Module in Odoo 17 Using the Scaffold Method
6710 130 ppt2
- 1. Level 1 Diploma in Wall and Floor Tiling © 2013 City and Guilds of London Institute. All rights reserved. 1 of 10 PowerPointpresentation Manually lifting and handling materials and accessories Unit 130: Handle and store tiling materials and accessories
- 2. Level 1 Diploma in Wall and Floor Tiling © 2013 City and Guilds of London Institute. All rights reserved. 2 of 10 Introduction The learning outcomes of this presentation will be: • a basic understanding of how to lift and handle materials • protection of work • manufacturers’ information.
- 3. Level 1 Diploma in Wall and Floor Tiling © 2013 City and Guilds of London Institute. All rights reserved. 3 of 10 Handling and storing materials Involves diverse operations: Manual material handling • Carrying bags or materials • Unpacking materials Material handling via machine • Forklift • Crane • Rigging Stacking or storing • Drums • Barrels • Timber • Loose bricks • Other materials
- 4. Level 1 Diploma in Wall and Floor Tiling © 2013 City and Guilds of London Institute. All rights reserved. 4 of 10 Injuries • Lifting an object is a major cause of back injuries in the workplace. • Improper storing and handling of material and equipment can cause ‘struck by’ and ‘crushed by’ injuries.
- 5. Level 1 Diploma in Wall and Floor Tiling © 2013 City and Guilds of London Institute. All rights reserved. 5 of 10 Source: Shutterstock
- 6. Level 1 Diploma in Wall and Floor Tiling © 2013 City and Guilds of London Institute. All rights reserved. 6 of 10 Hazards Common hazards include: • Improper manual lifting, or carrying loads that are too large or heavy • Being struck by materials or being caught in pinch points • Being crushed by machines, falling materials or improperly stored materials • Incorrectly cutting ties or securing devices. Source: Concerca
- 7. Level 1 Diploma in Wall and Floor Tiling © 2013 City and Guilds of London Institute. All rights reserved. 7 of 10 Manual handling Seek help: • When a load is too bulky to properly grasp or lift • When you can’t see around or over the load • When you can’t safely handle the load Attach handles to loads to reduce the chances of getting fingers smashed. Source: Shutterstock
- 8. Level 1 Diploma in Wall and Floor Tiling © 2013 City and Guilds of London Institute. All rights reserved. 8 of 10 Safe lifting • Break the load into parts. • Get help with heavy or bulky items. • Lift with legs, keep back straight, do not twist. • Use handling aids – such as steps, trestles, shoulder pads, handles, and wheels. • Avoid lifting above shoulder level.
- 9. Level 1 Diploma in Wall and Floor Tiling © 2013 City and Guilds of London Institute. All rights reserved. 9 of 10 Video link Below is a short video link to safe handling www.youtube.com/watch?v=QSPc9KY_VYc
- 10. Level 1 Diploma in Wall and Floor Tiling © 2013 City and Guilds of London Institute. All rights reserved. 10 of 10 Any questions?