10 Ways to Prevent ARC Welding Injury
•Download as PPTX, PDF•
1 like•111 views
10 Ways to Prevent ARC Welding Injury Arc welding is safe if the unit is properly installed and used. You can receive a shock, however, from the primary (input) voltage if you touch a lead or other electrically "hot" component inside the welder while any part of your body brushes the welder case or other grounded metal. If properly installed and used, the arc welder is very safe. If used improperly, the unit can expose welders to fire, explosion, and retinal burns.
Report
Share
Report
Share
Recommended
Safety Notes: Manual Metal Arc Welding
This document outlines safety precautions for metal arc welding. It discusses potential hazards such as burns from hot metal or radiation, electrical shock, and inhalation of dangerous fumes. Key safety recommendations include wearing personal protective equipment like flame-resistant clothing, welding shields, and respiratory protection. Proper ventilation and avoiding confined spaces are also advised to limit exposure to fumes.
Miller thunderbolt 225 ac
This document is an owner's manual for the Miller Thunderbolt 225 CC/AC Welding Power Source. It provides specifications for the welder including its rated output, amperage range, dimensions, weight, and other technical details. The majority of the document discusses important safety precautions for arc welding, including hazards from electric shock, arc rays, fumes and gases, compressed gas cylinders, and risks of fire or explosion. Proper protective equipment and ventilation are emphasized.
weldingsafety
Arc welding presents several safety hazards. The electric arc emits intense ultraviolet and infrared rays that can cause severe burns to skin and eyes. Molten metal sparks from the arc can reach temperatures of 2000-3000°F and cause burns or start fires if they land on flammable materials. To protect themselves, welders must wear protective clothing and equipment like helmets with proper shade lenses, gloves, and protective clothing to shield themselves from burns and rays. They must also take precautions to avoid electric shock, inhalation of harmful fumes, and fires by working in well-ventilated areas away from flammables while using safe welding practices.
arc_welding_safety[1]
The document discusses several safety hazards associated with electric arc welding. It notes that the high temperature arc and hot metal can cause severe burns. The electric arc also emits large amounts of ultraviolet and infrared rays invisible to the eye that can cause eye burns and sunburn. Molten metal droplets from the arc present burn and fire hazards. To be safe, welders must wear protective gear like helmets and gloves and work in well-ventilated areas to avoid burns, electric shock, harmful fumes, and fires. Proper precautions and safety equipment are necessary when engaging in electric arc welding.
Weldingintro
The document provides safety guidelines for arc welding equipment and practices. It describes proper use of the power switch, range selector, amperage control, cable attachments, ground clamp, electrode holder, welding table, electrodes, welding helmet, and other protective equipment. Guidelines address ventilation, protective clothing, eye protection, welding fumes, fire hazards, and safe welding behaviors.
General Welding Safety Practices.138344336521672.OS
This document provides an overview of general welding safety practices and hazards. It defines welding as a method of joining metal through fusion using heat. Key welding hazards discussed include radiation exposure, electric shock, fires and explosions, fumes and gases, confined spaces, and loud noise. The document outlines proper personal protective equipment including clothing, eye protection, and welding hoods. It also covers first aid procedures for cuts and other emergencies.
15 electro staticdischarge1g
The document discusses electrostatic discharge and its risks. It explains that a static charge builds up from certain materials rubbing together, like clothes or one item against another. This charge can damage electronic components through sparks or discharges. Anyone working with electronics must wear a wristband and use a grounded mat to safely dissipate any static charge and prevent damage.
Welding and Cutting Safety Training by the University of Southern Mississippi
Welding and Cutting Safety Training by the University of Southern MississippiAtlantic Training, LLC.
This document discusses welding safety hazards and controls. It covers health hazards from welding fumes and gases, which can cause lung diseases and cancer. Engineering controls like ventilation and personal protective equipment like respirators are recommended to reduce exposure. Other safety topics addressed include electrical, fire, ergonomic, and compressed gas cylinder hazards, as well as general safe work practices for welding.Recommended
Safety Notes: Manual Metal Arc Welding
This document outlines safety precautions for metal arc welding. It discusses potential hazards such as burns from hot metal or radiation, electrical shock, and inhalation of dangerous fumes. Key safety recommendations include wearing personal protective equipment like flame-resistant clothing, welding shields, and respiratory protection. Proper ventilation and avoiding confined spaces are also advised to limit exposure to fumes.
Miller thunderbolt 225 ac
This document is an owner's manual for the Miller Thunderbolt 225 CC/AC Welding Power Source. It provides specifications for the welder including its rated output, amperage range, dimensions, weight, and other technical details. The majority of the document discusses important safety precautions for arc welding, including hazards from electric shock, arc rays, fumes and gases, compressed gas cylinders, and risks of fire or explosion. Proper protective equipment and ventilation are emphasized.
weldingsafety
Arc welding presents several safety hazards. The electric arc emits intense ultraviolet and infrared rays that can cause severe burns to skin and eyes. Molten metal sparks from the arc can reach temperatures of 2000-3000°F and cause burns or start fires if they land on flammable materials. To protect themselves, welders must wear protective clothing and equipment like helmets with proper shade lenses, gloves, and protective clothing to shield themselves from burns and rays. They must also take precautions to avoid electric shock, inhalation of harmful fumes, and fires by working in well-ventilated areas away from flammables while using safe welding practices.
arc_welding_safety[1]
The document discusses several safety hazards associated with electric arc welding. It notes that the high temperature arc and hot metal can cause severe burns. The electric arc also emits large amounts of ultraviolet and infrared rays invisible to the eye that can cause eye burns and sunburn. Molten metal droplets from the arc present burn and fire hazards. To be safe, welders must wear protective gear like helmets and gloves and work in well-ventilated areas to avoid burns, electric shock, harmful fumes, and fires. Proper precautions and safety equipment are necessary when engaging in electric arc welding.
Weldingintro
The document provides safety guidelines for arc welding equipment and practices. It describes proper use of the power switch, range selector, amperage control, cable attachments, ground clamp, electrode holder, welding table, electrodes, welding helmet, and other protective equipment. Guidelines address ventilation, protective clothing, eye protection, welding fumes, fire hazards, and safe welding behaviors.
General Welding Safety Practices.138344336521672.OS
This document provides an overview of general welding safety practices and hazards. It defines welding as a method of joining metal through fusion using heat. Key welding hazards discussed include radiation exposure, electric shock, fires and explosions, fumes and gases, confined spaces, and loud noise. The document outlines proper personal protective equipment including clothing, eye protection, and welding hoods. It also covers first aid procedures for cuts and other emergencies.
15 electro staticdischarge1g
The document discusses electrostatic discharge and its risks. It explains that a static charge builds up from certain materials rubbing together, like clothes or one item against another. This charge can damage electronic components through sparks or discharges. Anyone working with electronics must wear a wristband and use a grounded mat to safely dissipate any static charge and prevent damage.
Welding and Cutting Safety Training by the University of Southern Mississippi
Welding and Cutting Safety Training by the University of Southern MississippiAtlantic Training, LLC.
This document discusses welding safety hazards and controls. It covers health hazards from welding fumes and gases, which can cause lung diseases and cancer. Engineering controls like ventilation and personal protective equipment like respirators are recommended to reduce exposure. Other safety topics addressed include electrical, fire, ergonomic, and compressed gas cylinder hazards, as well as general safe work practices for welding.Safe practices while Welding, Gas cutting and machining activities
This presentation contains safety practices to be followed by technicians while working on a job. The slides do not contain engineering details of the equipment or ISO , NFCA standards
Work Hazards: The Potential Safety Risks of Welding
All welders must pay close attention to their safety whenever there is a project in progress. Although arc welding is generally safe, it can become a risky occupation if the welder does not observe proper safety precautions. Welding operators have to address a range of safety hazards associated with the craft. These hazards include:
ELEC SAFETY IN WELDING AND CUTTING=1
This document outlines several hazards associated with welding and cutting, including radiation hazards, dangerous fumes and gases, burns and eye injuries, fire and explosion hazards, and more. It discusses specific hazards like ultraviolet rays causing eye damage and electric shock. It provides precautions for these hazards such as using proper eye protection, gloves, protective clothing, and ensuring equipment is grounded, cables are dry and insulated, and work areas are ventilated. Safety practices for electric arc welding like equipment checks, set up, and general precautions are also covered.
Safety precaution for welding and cutting
This document provides safety precautions for welding and cutting. It discusses hazards such as electric shock, electromagnetic radiation, fires and explosions, and harmful fumes and gases. Key precautions include wearing protective equipment like gloves, goggles and boots; ensuring adequate ventilation; checking equipment is grounded and in good condition; and having fire extinguishers available in case of emergency. The document also classifies different types of fires and their appropriate extinguishing methods.
Ppeppt general industry
This document outlines an employer's responsibilities to protect employees from workplace hazards through implementing engineering controls, work practice controls, and personal protective equipment (PPE) when other controls do not eliminate hazards. It emphasizes that PPE should only be used as a last resort and provides examples of common types of PPE including eye, head, foot, hand, and body protection as well as guidance on establishing a PPE program and training employees on proper PPE use.
The welding workshop group 3
Presentation done by 15-16 year old students in a technical school, applying contents from English, Workshop and IT.
Arc welding & safty
Arc welding is a process that joins metals through intense heat. It requires equipment like an electrode, electrode holder, welding machine and cables. Hazards include falls, crushing injuries, fires/explosions, and electrocution. Proper safety equipment like eye protection and barriers are needed, as well as ensuring a safe work environment and properly maintained welding equipment.
Welding
Welding is a common method of joining metals that involves fusing two pieces together. It carries several hazards including impact, penetration, harmful fumes and heat/light radiation. Welding is considered high risk, especially in operating plants, but risks can be reduced through various defenses including training, barriers, permits, communication, assessments, PPE, supervision and emergency preparedness. Proper PPE like welding helmets, gloves, aprons and leg covers are required to prevent burns from hot metal and radiation. Spark containment and protecting others is also important for safety.
Welding and cutting safety
Welding and cutting involves many hazards that require extensive safety procedures and training to control. Common hazards include compressed gases, electricity, fumes, gases, noise, radiation, fire and explosions. Proper handling and storage of compressed gas cylinders, use of protective equipment like gloves, clothing, ventilation and respirators, avoiding electrical shock, and fire precautions are all critical to ensure safety when welding and cutting. Thorough training is also needed for workers to safely use equipment and procedures that control hazardous conditions.
BeginningWelding
This document provides an overview of arc welding, including definitions of key terms, descriptions of common equipment, safety procedures, and an explanation of the American Welding Society electrode classification system. It defines arc welding as using an electric arc to fuse metals, and outlines various types of welding machines, electrodes, the purpose of fluxes, how to establish an arc, and characteristics of proper arc length. Safety precautions are also summarized.
Fire & explosion hazards in welding -Safety
This document discusses welding hazards from fires and explosions. It notes that fires require only a heat source while explosions require heat or shock. Key causes of fires and explosions during welding include sparks and hot metal. The document outlines fire and explosion hazards from gases used in welding like oxygen and acetylene. It discusses OSHA regulations on managing ignition sources and flammable substances. Control measures include isolating fuels from sparks and using protective equipment. A case study describes a fatal explosion caused by welding sparks igniting vapors from unpurged tanks.
Robotics Tool Training
Power tools and hand tools require proper safety equipment and techniques to avoid injury. Safety glasses and gloves should always be worn when using tools. Guards and safety switches on power tools should never be disabled or altered. Hand tools also need to be used properly with awareness of pinch points and using the right tool for the job. A clean, organized work area helps maintain safety.
Welding safety hazard
This document outlines various welding safety hazards and recommendations for reducing risks. It identifies health hazards from welding fumes, gases and particles that can cause both short-term and long-term effects. It also discusses electrical, fire, explosion, trip, fall, compressed gas, and noise hazards. The document provides tips for identifying hazards, using engineering controls, protective equipment, and following basic safety rules to reduce risks when welding.
Welding Safety 2014
This document discusses welding safety hazards and regulations. It begins by describing past welding incidents that resulted in injuries or fatalities. Some key risks mentioned include falls, electrical hazards, fires, confined space hazards, and exposure to toxic fumes and gases. The document then outlines OSHA regulations on compressed gas cylinder safety, personal protective equipment, and controlling hazards like lead, hexavalent chromium, and heat exposure during welding operations. Protecting workers from these risks requires following safety protocols for cylinder handling and storage, electrical safety, housekeeping, ventilation, and use of proper protective equipment.
Soldering techniques
Soldering is the process of connecting components into a circuit. Safety precautions for soldering include not touching the hot soldering iron tip, avoiding touching wires with the tip, and returning the iron to its stand when not in use. To prepare the soldering iron, place it in its stand to heat up, dampen the cloth, wipe the hot tip, and melt solder onto the tip. Useful soldering tips are to keep the tip clean, double check joints, solder small parts first, and ensure leads are smooth. There are two types of soldering: rough and smooth.
Arc Welding Basics
This document provides an overview of arc welding basics. It introduces arc welding and discusses its importance. Safety is emphasized, covering hazards like fumes, electric shock, and fire. The document explains welding fundamentals such as electricity, metals, joints, positions and electrode classification. Key terms are defined and objectives focus on safety, terminology, welding symbols and career opportunities in welding.
Improving your SMAW welding technique
This document provides guidance on shielded metal arc welding (SMAW). It discusses several key considerations for SMAW including:
1. Proper preparation of the welding area by removing dirt and rust to avoid defects.
2. Using the correct current setting based on electrode diameter to achieve a stable arc without excess spatter or lack of penetration.
3. Maintaining the proper arc length, which is less than the electrode diameter, and angle of the electrode for quality welds.
4. Developing welding technique through practice, including electrode manipulation and travel speed to control the weld puddle.
Hot Work Permit Program Safety Training by UNC
This document provides an overview of hot work safety training at UNC. It defines hot work as any work involving burning, welding, or similar operations that can ignite fires or explosions. The training covers hazards associated with hot work like fires, explosions, and physical injuries. It explains requirements for the UNC hot work permit program including only allowing hot work in designated or controlled areas, not in non-permissible locations. A hot work permit must be obtained for controlled areas and includes precautions to implement like ensuring fire protection equipment and controlling fuel sources within 35 feet of the hot work.
Welding Safety by Pennsylvania L&I
This document provides an overview of welding safety regulations and guidelines. It summarizes OSHA regulations on gas welding (1926.350), arc welding (1926.351), fire prevention (1926.352), ventilation (1926.353), and preservative coatings (1926.354). Key safety topics covered include proper handling and storage of gas cylinders, use of protective equipment, fire hazards, ventilation requirements, and training on welding equipment and processes. The document aims to educate welders on health and safety risks and how to work safely according to OSHA standards.
Site Orientation and Setup
This document provides training information for a construction site supervisor. It outlines evacuation procedures that all employees must be trained on, such as recognizing alarm signals and safely exiting buildings. It describes potential reasons for evacuation like fires or chemical releases. The document also discusses hazards found in different areas of the work site like soft ground, energized electrical equipment, and proper personal protective equipment. Safety protocols are presented for controlling hazardous energy sources, storing chemicals, and preventing accidental contact with electrical panels.
Ehsd0348
Soldering involves risks of burns, toxic fume inhalation, and electrical hazards that require safety precautions. The document outlines steps to take such as wearing eye protection, working in a ventilated area, using a soldering iron stand, and properly disposing of wastes to reduce risks when soldering. Precautions like avoiding touching hot elements, keeping sponges wet, and turning off equipment when not in use can prevent burns. Proper ventilation, personal protective equipment, and avoiding lead use help limit inhalation of toxic fumes from soldering.
Safe Welding Practices
Welding can expose workers to dangerous fumes, gases, burns, fires, and electric shock if proper safety precautions are not followed. Workers should wear approved safety equipment like helmets, gloves, protective clothing and ventilate work areas. They should also keep combustible materials away from welding areas, use fire extinguishers, and obtain hot work permits when needed. Proper grounding and insulation of equipment is also needed to prevent electric shock, which can be fatal. All incidents, no matter how small, must be reported.
More Related Content
What's hot
Safe practices while Welding, Gas cutting and machining activities
This presentation contains safety practices to be followed by technicians while working on a job. The slides do not contain engineering details of the equipment or ISO , NFCA standards
Work Hazards: The Potential Safety Risks of Welding
All welders must pay close attention to their safety whenever there is a project in progress. Although arc welding is generally safe, it can become a risky occupation if the welder does not observe proper safety precautions. Welding operators have to address a range of safety hazards associated with the craft. These hazards include:
ELEC SAFETY IN WELDING AND CUTTING=1
This document outlines several hazards associated with welding and cutting, including radiation hazards, dangerous fumes and gases, burns and eye injuries, fire and explosion hazards, and more. It discusses specific hazards like ultraviolet rays causing eye damage and electric shock. It provides precautions for these hazards such as using proper eye protection, gloves, protective clothing, and ensuring equipment is grounded, cables are dry and insulated, and work areas are ventilated. Safety practices for electric arc welding like equipment checks, set up, and general precautions are also covered.
Safety precaution for welding and cutting
This document provides safety precautions for welding and cutting. It discusses hazards such as electric shock, electromagnetic radiation, fires and explosions, and harmful fumes and gases. Key precautions include wearing protective equipment like gloves, goggles and boots; ensuring adequate ventilation; checking equipment is grounded and in good condition; and having fire extinguishers available in case of emergency. The document also classifies different types of fires and their appropriate extinguishing methods.
Ppeppt general industry
This document outlines an employer's responsibilities to protect employees from workplace hazards through implementing engineering controls, work practice controls, and personal protective equipment (PPE) when other controls do not eliminate hazards. It emphasizes that PPE should only be used as a last resort and provides examples of common types of PPE including eye, head, foot, hand, and body protection as well as guidance on establishing a PPE program and training employees on proper PPE use.
The welding workshop group 3
Presentation done by 15-16 year old students in a technical school, applying contents from English, Workshop and IT.
Arc welding & safty
Arc welding is a process that joins metals through intense heat. It requires equipment like an electrode, electrode holder, welding machine and cables. Hazards include falls, crushing injuries, fires/explosions, and electrocution. Proper safety equipment like eye protection and barriers are needed, as well as ensuring a safe work environment and properly maintained welding equipment.
Welding
Welding is a common method of joining metals that involves fusing two pieces together. It carries several hazards including impact, penetration, harmful fumes and heat/light radiation. Welding is considered high risk, especially in operating plants, but risks can be reduced through various defenses including training, barriers, permits, communication, assessments, PPE, supervision and emergency preparedness. Proper PPE like welding helmets, gloves, aprons and leg covers are required to prevent burns from hot metal and radiation. Spark containment and protecting others is also important for safety.
Welding and cutting safety
Welding and cutting involves many hazards that require extensive safety procedures and training to control. Common hazards include compressed gases, electricity, fumes, gases, noise, radiation, fire and explosions. Proper handling and storage of compressed gas cylinders, use of protective equipment like gloves, clothing, ventilation and respirators, avoiding electrical shock, and fire precautions are all critical to ensure safety when welding and cutting. Thorough training is also needed for workers to safely use equipment and procedures that control hazardous conditions.
BeginningWelding
This document provides an overview of arc welding, including definitions of key terms, descriptions of common equipment, safety procedures, and an explanation of the American Welding Society electrode classification system. It defines arc welding as using an electric arc to fuse metals, and outlines various types of welding machines, electrodes, the purpose of fluxes, how to establish an arc, and characteristics of proper arc length. Safety precautions are also summarized.
Fire & explosion hazards in welding -Safety
This document discusses welding hazards from fires and explosions. It notes that fires require only a heat source while explosions require heat or shock. Key causes of fires and explosions during welding include sparks and hot metal. The document outlines fire and explosion hazards from gases used in welding like oxygen and acetylene. It discusses OSHA regulations on managing ignition sources and flammable substances. Control measures include isolating fuels from sparks and using protective equipment. A case study describes a fatal explosion caused by welding sparks igniting vapors from unpurged tanks.
Robotics Tool Training
Power tools and hand tools require proper safety equipment and techniques to avoid injury. Safety glasses and gloves should always be worn when using tools. Guards and safety switches on power tools should never be disabled or altered. Hand tools also need to be used properly with awareness of pinch points and using the right tool for the job. A clean, organized work area helps maintain safety.
Welding safety hazard
This document outlines various welding safety hazards and recommendations for reducing risks. It identifies health hazards from welding fumes, gases and particles that can cause both short-term and long-term effects. It also discusses electrical, fire, explosion, trip, fall, compressed gas, and noise hazards. The document provides tips for identifying hazards, using engineering controls, protective equipment, and following basic safety rules to reduce risks when welding.
Welding Safety 2014
This document discusses welding safety hazards and regulations. It begins by describing past welding incidents that resulted in injuries or fatalities. Some key risks mentioned include falls, electrical hazards, fires, confined space hazards, and exposure to toxic fumes and gases. The document then outlines OSHA regulations on compressed gas cylinder safety, personal protective equipment, and controlling hazards like lead, hexavalent chromium, and heat exposure during welding operations. Protecting workers from these risks requires following safety protocols for cylinder handling and storage, electrical safety, housekeeping, ventilation, and use of proper protective equipment.
Soldering techniques
Soldering is the process of connecting components into a circuit. Safety precautions for soldering include not touching the hot soldering iron tip, avoiding touching wires with the tip, and returning the iron to its stand when not in use. To prepare the soldering iron, place it in its stand to heat up, dampen the cloth, wipe the hot tip, and melt solder onto the tip. Useful soldering tips are to keep the tip clean, double check joints, solder small parts first, and ensure leads are smooth. There are two types of soldering: rough and smooth.
Arc Welding Basics
This document provides an overview of arc welding basics. It introduces arc welding and discusses its importance. Safety is emphasized, covering hazards like fumes, electric shock, and fire. The document explains welding fundamentals such as electricity, metals, joints, positions and electrode classification. Key terms are defined and objectives focus on safety, terminology, welding symbols and career opportunities in welding.
Improving your SMAW welding technique
This document provides guidance on shielded metal arc welding (SMAW). It discusses several key considerations for SMAW including:
1. Proper preparation of the welding area by removing dirt and rust to avoid defects.
2. Using the correct current setting based on electrode diameter to achieve a stable arc without excess spatter or lack of penetration.
3. Maintaining the proper arc length, which is less than the electrode diameter, and angle of the electrode for quality welds.
4. Developing welding technique through practice, including electrode manipulation and travel speed to control the weld puddle.
Hot Work Permit Program Safety Training by UNC
This document provides an overview of hot work safety training at UNC. It defines hot work as any work involving burning, welding, or similar operations that can ignite fires or explosions. The training covers hazards associated with hot work like fires, explosions, and physical injuries. It explains requirements for the UNC hot work permit program including only allowing hot work in designated or controlled areas, not in non-permissible locations. A hot work permit must be obtained for controlled areas and includes precautions to implement like ensuring fire protection equipment and controlling fuel sources within 35 feet of the hot work.
Welding Safety by Pennsylvania L&I
This document provides an overview of welding safety regulations and guidelines. It summarizes OSHA regulations on gas welding (1926.350), arc welding (1926.351), fire prevention (1926.352), ventilation (1926.353), and preservative coatings (1926.354). Key safety topics covered include proper handling and storage of gas cylinders, use of protective equipment, fire hazards, ventilation requirements, and training on welding equipment and processes. The document aims to educate welders on health and safety risks and how to work safely according to OSHA standards.
Site Orientation and Setup
This document provides training information for a construction site supervisor. It outlines evacuation procedures that all employees must be trained on, such as recognizing alarm signals and safely exiting buildings. It describes potential reasons for evacuation like fires or chemical releases. The document also discusses hazards found in different areas of the work site like soft ground, energized electrical equipment, and proper personal protective equipment. Safety protocols are presented for controlling hazardous energy sources, storing chemicals, and preventing accidental contact with electrical panels.
What's hot (20)
Safe practices while Welding, Gas cutting and machining activities
Safe practices while Welding, Gas cutting and machining activities
Work Hazards: The Potential Safety Risks of Welding
Work Hazards: The Potential Safety Risks of Welding
Similar to 10 Ways to Prevent ARC Welding Injury
Ehsd0348
Soldering involves risks of burns, toxic fume inhalation, and electrical hazards that require safety precautions. The document outlines steps to take such as wearing eye protection, working in a ventilated area, using a soldering iron stand, and properly disposing of wastes to reduce risks when soldering. Precautions like avoiding touching hot elements, keeping sponges wet, and turning off equipment when not in use can prevent burns. Proper ventilation, personal protective equipment, and avoiding lead use help limit inhalation of toxic fumes from soldering.
Safe Welding Practices
Welding can expose workers to dangerous fumes, gases, burns, fires, and electric shock if proper safety precautions are not followed. Workers should wear approved safety equipment like helmets, gloves, protective clothing and ventilate work areas. They should also keep combustible materials away from welding areas, use fire extinguishers, and obtain hot work permits when needed. Proper grounding and insulation of equipment is also needed to prevent electric shock, which can be fatal. All incidents, no matter how small, must be reported.
Guide
This document provides safety guidelines for various tools and equipment commonly found in agricultural mechanics laboratories. It details proper procedures and safety precautions for using power tools like drills, saws, jointers and planers to prevent accidents and injuries. Specific guidelines are provided for welding equipment, compressed air, hand tools and more. Laboratory safety is emphasized, including wearing proper protective equipment and avoiding distractions or horseplay.
Safety guide
This document provides safety guidelines for agricultural laboratories and mechanics workshops. It outlines general safety rules regarding equipment use, personal protective equipment, tool safety, welding, and other hazardous activities. Specific guidelines are provided for power tools, compressed air, greenhouses, drills, sanders, saws, welders, and oxy-acetylene equipment. Students are instructed to follow all safety procedures and get permission before operating any machinery.
DaY 1.docx
Electrical and electronics symbols represent electrical components in schematic diagrams. Common symbols include those for wires, batteries, resistors, and transistors. It is important to follow safety precautions when working with electrical equipment, such as wearing protective equipment, ensuring proper ventilation, and turning off power before working on circuits to avoid injury from electrical currents. Students working in electronics laboratories should abide by additional rules like wearing safety glasses and keeping work areas clean.
Safety in mechanical maintenance
Safety is the highest priority when entering confined spaces due to hazards like oxygen deficiency caused by consumption, displacement, or reaction which can occur in concentrations below 19.5% or above 23%. Proper equipment, training, and permitting procedures must be followed that designate roles for the entrant, attendant, and safety representative to prevent injury when working in confined spaces.
safetyinmechmaintenance-150925033622-lva1-app6891.pdf
The document discusses safety procedures for confined space entry. It defines key roles like entrant and attendant. Hazards of confined spaces include oxygen deficiency, oxygen enrichment, and toxic gases. A confined space entry permit is required which evaluates hazards and prescribes precautions. Spaces must be tested for gases and oxygen levels, and ventilated if needed. Entrants must be monitored and evacuated if alarm activates. Attendants assist but do not enter, and emergency rescue is only by trained personnel. Proper PPE, lighting, communication, and rescue equipment are required for safe confined space entry.
Power tools safety
Power tools can cause serious injuries if not properly maintained and safely operated. Workers should inspect tools for defects before each use, only use tools for their intended purposes, and wear appropriate personal protective equipment. Following manufacturers' instructions and maintaining good footing can help prevent accidents and injuries when operating power tools. Defective tools should be immediately taken out of service and reported to supervisors.
Electrician Lab Safety Rules for ITI
This document outlines various safety measures that must be followed when working in an electrical lab. Key rules include: only entering the lab with permission, behaving orderly, inspecting equipment for damage before use, never stripping wires with teeth or knives, not disconnecting plugs by pulling cables, ensuring circuits are clear before energizing conductors, turning off the main switch before replacing fuses, using screwdrivers when working on circuits, standing on rubber mats, properly positioning ladders, using earth connections, and disconnecting power immediately in emergencies. Proper safety precautions are necessary to prevent accidents like electrical shocks.
Máy bắt vít dùng pin dtd137 rfe introduction manual
Máy bắt vít dùng pin dtd137 rfe introduction manualCông ty cổ phần OKS | Tổng thầu thi công Nhà máy GMP, Tổng thầu thi công Nhà kho GSP
This document provides instructions for two cordless impact driver models, the DTD137 and DTD148. It includes specifications for the tools, such as voltage, speed, dimensions, and weight. It also provides important safety warnings and instructions for proper use, maintenance, and battery care. Symbols used on the tools are explained. Functions like installing the battery, battery capacity indication, and reversing the direction of rotation are described.Máy chà nhám quỹ đạo tròn MT922 (2)
Máy chà nhám quỹ đạo tròn MT922 (2)Công ty cổ phần OKS | Tổng thầu thi công Nhà máy GMP, Tổng thầu thi công Nhà kho GSP
This instruction manual provides specifications and safety instructions for using a random orbit sander. It details that the sander has a 125mm paper size and 12,000 orbits per minute. The manual emphasizes safety, including wearing eye protection and avoiding exposure to dust. It instructs the user to hold the sander firmly, place it gently against the workpiece, and apply slight pressure while sanding. Maintenance such as replacing carbon brushes must be done by an authorized service center.ELECTRICAL SAFETY PRESENTATION.ppt
This document provides an overview of electrical safety. It discusses the purpose of electrical safety training, basic concepts of electricity, hazards recognition, effects of electricity on the human body, and hazard protection methods. It outlines work practices for using electrical tools and equipment safely, as well as responsibilities of supervisors and employees. Specific safety topics covered include inspecting cords and equipment, keeping electrical panels clear, avoiding trip hazards, locking out power sources, using personal protective equipment, and emergency response procedures. The goal is to raise awareness of electrical hazards and instruct safe work practices to prevent electrical accidents.
TEXTO - Hand Tools
This document provides guidance on safely using various common hand tools. It details proper techniques for tools like hammers, saws, chisels, and others. The key points made are:
- Workers must be trained on proper hand tool usage to prevent injuries
- Tools should be well-maintained and stored safely when not in use
- Using the right tool for each job and proper techniques are necessary for safety
Electrical work genral safety precautions
1) Before working on any electrical circuit or apparatus, switches must be opened and locked and safety precautions taken to ensure the circuit is dead.
2) Never work on live circuits without authorization. Treat all circuits as live until proven dead.
3) Wear appropriate protective equipment like rubber gloves and avoid loose clothing when working with electricity. Maintain a safe distance from energized equipment.
craftsman saw.pdf
This owner's manual provides instructions for safely operating a 7-1/4 inch circular saw. It describes the key features of the saw including the switch, spindle lock, guards, and adjustments for depth of cut and bevel angle. The manual outlines important safety rules and warnings for circular saw use, such as keeping hands away from the blade, wearing safety glasses, and avoiding kickback. It also provides specifications for the saw and explains how to perform basic maintenance.
Hand and power tools
This document discusses safety procedures for using hand and power tools. It identifies five basic safety rules, including keeping tools in good condition, using the proper tool for the job, inspecting tools before and after use, following manufacturer's instructions, and using required safety equipment. It outlines hazards of hand tools such as using chisels improperly or tools with loose handles. It also details power tool hazards like not disconnecting tools, removing safety guards, or using tools in wet conditions. Proper handling and storage of gasoline-powered tools is also addressed.
Máy cưa đĩa Makita MT583
Máy cưa đĩa Makita MT583Công ty cổ phần OKS | Tổng thầu thi công Nhà máy GMP, Tổng thầu thi công Nhà kho GSP
This document provides instructions for operating a circular saw. It includes specifications for the saw such as its blade diameter, maximum cutting depth, speed, weight, and safety ratings. The document outlines safety warnings and proper procedures for circular saw use, including adjusting the depth and bevel of cuts, ensuring the blade guard is closed, and kickback prevention. It describes the functions of the saw, including operating the on/off switch, and emphasizes the importance of following all safety instructions to avoid injury.ICT handtool-safety-training.pptx
The document provides safety guidelines and regulations for both hand tools and power tools. It discusses hazards associated with different types of tools and outlines precautions that should be taken. For hand tools, the main hazards come from misuse and improper maintenance. For power tools, following manufacturers' instructions and wearing proper protective equipment is emphasized. Specific guidance is given for circular saws, drills, abrasive wheels, miter boxes, and pneumatic tools. Employees have a shared responsibility with employers to work safely using the right tools for each task.
GENERAL SAFETY RULESWARNING Read and understand all instruc.docx
- The document provides safety instructions for operating power tools. It details rules for work areas, electrical safety, personal safety, tool use and care, and specific safety rules for drills.
- Key information includes only operating reversing drills in forward or reverse, securely tightening chucks using all holes, and not attempting to change accessories while the drill is running.
- Safety is emphasized throughout including keeping work areas organized, avoiding electric shock from water, wearing proper protective equipment, and not forcing a stalled drill.
Volvo ew55 b compact wheel excavator service repair manual
This document provides safety precautions and guidelines for servicing equipment. It outlines general safety practices like using protective gear, preparing for emergencies, handling fluids safely, and working in contaminated environments. It also describes specific cautions for operations like servicing the cooling system, avoiding high pressure fluids, handling heavy objects, working with electrical systems, and preparing the work area before starting service work.
Similar to 10 Ways to Prevent ARC Welding Injury (20)
safetyinmechmaintenance-150925033622-lva1-app6891.pdf
safetyinmechmaintenance-150925033622-lva1-app6891.pdf
Máy bắt vít dùng pin dtd137 rfe introduction manual
Máy bắt vít dùng pin dtd137 rfe introduction manual
GENERAL SAFETY RULESWARNING Read and understand all instruc.docx
GENERAL SAFETY RULESWARNING Read and understand all instruc.docx
Volvo ew55 b compact wheel excavator service repair manual
Volvo ew55 b compact wheel excavator service repair manual
More from Dwarika Bhushan Sharma
5 - CLOWNS BELONG IN THE CIRCUS & NOT ON THE JOB.pdf
5 - CLOWNS BELONG IN THE CIRCUS & NOT ON THE JOB
3-STOP FALLS, CLEAN UP, PICK UP, WIPE UP.pdf
3-STOP FALLS, CLEAN UP, PICK UP, WIPE UP3-STOP FALLS, CLEAN UP, PICK UP, WIPE UP-STOP FALLS, CLEAN UP, PICK UP, WIPE UP
2-THERE'S A SAFE WAY TO DO EVERY JOB, OF YOU DON'T KNOW ASK.pdf
2-THERE'S A SAFE WAY TO DO EVERY JOB, OF YOU DON'T KNOW ASK 2-THERE'S A SAFE WAY TO DO EVERY JOB, OF YOU DON'T KNOW ASK
1-HAZARDOUS CHEMICALS.pdf
This document provides the name of a company but no other details. It contains only the words "Company Name" with no other context or information provided. In just two words, the document states the name of a company without any other descriptive text.
PRE-START BRIEFING Form # HSEQ - PSB Rev 2 -.docx
Project Information:
Project Name:
Location: Supervisor :
Company name : Date:
Task Description:
Before work starts, the following must be in place
Induction Supervision Test Certificates Communication in same language Method Statement Risk Assessment Permit To Work Area Lighting
SELECT HAZARDS SELECT CONTROLS
( Tick to identify the controls in place)
Fall from height Training Access Ladder Access Handrail Edge Protection Secure Ladder Adequate Work Platform Guards for Openings Safety Harness Life Lines
Others( Specify)
Manual Handling Training Check Weight Mechanical Aids Access Route Team Lifting Wrong method Right Method
Power tools Training Color code inspection tag Check Cable Wheel guards Safe plug & sockets Cable Protection Proper Scaffold Cable Overhead Rotatory part guards
Scaffold Scaffold Tag Edge Protection Check Overhead works Access Ladder Adequate Work Platform Weather condition Out riggers Ladder 3 feet above platform Safety Harness
SELECT HAZARDS SELECT CONTROLS
( Tick to identify the controls in place)
Risk Assessment
Lifting Plan Tag Lines Lifting points / hooks Banks man Load stability Check Lifting gear Examination /Inspection Sharp edges protected
Lifting operations Weather/ Wind Speed Ground conditions Exclusion zone Communication Loading/ unloading vehicles Spreader Beams Check Ground conditions Check outriggers Others
Fire Fire Extinguisher Fire Hose Fire Exit Assembly point others
Slip/Trip Clean before you go Barricade the waste Waste Management Clean Access Housekeeping Clean liquid spillage Access signs Maintain access/ Egress
PPE
Safety Harness
Safety Helmet Coveralls Hi vis Jacket Safety Shoe Face Shield Ear Protection
Dust mask Respiratory Equipment Life line/ harness anchorage Hand Gloves Goggles/ Glass
Pre start Briefing done by: Signature:
Reviewed By HSE Manager/ In charge: Signature:
FIRE PREVENTION REQUIREMENTS Form # HSEQ - Rev 2.docx
Code of Practice
C.O.P # 01
Fire Prevention Requirements
(Management of Combustible Materials & Electrical Inspections)
Rev. 01, Mar 23
SUB CONTRACTORS HSE CHECKLIST Form # HSEQ - SPSC Rev 2 -.docx
This document is a sub-contractor pre-start HSE checklist that must be filled out daily before starting any activity. It collects project information, task details including description, location, workers and duration. It also checks that various HSE prerequisites are in place such as safety inductions, risk assessments, PPE availability, inspection of tools and equipment, and that unsafe conditions have been rectified. The sub-contractor must acknowledge that all precautions and control measures have been taken and the workers have been deemed competent to perform the task safely.
STORE INSPECTION Form # HSEQ - Form 2 Rev 2.docx
Project Information
Project Name: Store No.
Location: Contact Person:
Company Name: Arabtec Construction LLC. Date:
Sr. Description Yes No N/A Comments
1. Is access to stores are restricted to authorized personnel only?
2. Are there clear spaces around racks and stacks of stored materials and are adequate gangways provided between them?
3. Are stacks and storage kept clear of light fittings and hot surfaces?
4. Are all stocks of flammable liquids kept in purpose-built flammable storage liquid stores?
5. Are storage areas generally cleaned and tidy?
6. Are flammable liquids kept away from all possible sources of ignition?
7. Emergency exit signs are available in right locations
8. Smoke detectors/fire alarm are visible and accessible.
9. Fire extinguishers are available are serviced regularly
10. Are free standing shelves and cupboards secured for stability?
11. Are heavy items stored at a suitable height?
12. Are chemical containers used for storage suitable and clearly labelled?
13. Is there adequate light in the storage area?
14. Are all small loose items secured in appropriate storage?
15. Are warning notices, prohibiting smoking and naked lights prominently displayed?
16. Others if any:
Remarks:
Inspected by: Signature:
Reviewed by Project Manager/HSE Manager Signature:
WITNESS STATEMENT FORM.docx
This document records a statement for a project located at an unspecified location. The statement is provided and written by an individual who acknowledges that the information is true to the best of their recollection. The individual provides their name, signature, position and date at the end of the statement.
PROJECT LEADER INCIDENT BRIEFING Form # HSEQ - PLIB Rev 2 -.docx
1. Project Information:
Project Name: Click here to enter text.
Report No.: Click here to enter text.
Project Location: Click here to enter text.
Property No.: Click here to enter text.
☐ Fatality ☐ Major Injury ☐ Minor Injury ☐ Property Damage ☐ Environmental ☐ Other
2. Describe the Incident in detail:
Answer who, what, why, where, when & how in this section: (Attach additional pages if required)
3. Incident Root Causes:
Describe direct, indirect & root cause: (Attach additional pages if required)
4. Key Corrections Taken Immediately after the Incident:
Attach additional pages if more space is required:
5. Key Corrective Actions to Prevent Recurrence:
Describe the corrective actions with timeframe: (Attach additional pages if required)
Corporate Office Remarks:
HSE FORMS (COVER PAGE)2 Form # HSEQ - Rev 2.docx
This document pertains to health, safety, environment, and quality forms from an HSEQ department. The HSEQ department handles forms related to health, safety, environment, and quality assurance. No other details are provided about the specific forms or purpose of the HSEQ department.
LIFT SHAFT ENTRY PERMIT Form # HSEQ - LSEP Rev 2 -.docx
1. Project Information: (To be filled by initiator/originator)
Project Name: Permit No.:
Project Location:
Requesting Contractor/Company
2. Permit Issuance Details: (To be filled by initiator/originator)
THIS PERMIT IS ONLY FOR ONE SHIFT AND NOT EXTENDABLE
Description of Task:
Detail of Surroundings:
Permit Validity:
Time (from): __________Hrs.
Time (To): __________Hrs.
Date:
3. Control Measures: (To be filled by initiator/originator and verified by Evaluator)
Checks Yes-No-NA Checks Yes-No-NA
Method statement & Risk assessment developed, approved & communicated? ☐ ☐ ☐
Availability of rescue procedure and equipment? ☐ ☐ ☐
Operatives are trained and competent? ☐ ☐ ☐
Workplace appropriately illuminated ☐ ☐ ☐
Any high risk activity associated that requires PTW (i.e. hot work, CSE)? ☐ ☐ ☐
Forced ventilation provided? ☐ ☐ ☐
Are all necessary Permit approved and displayed at work location? ☐ ☐ ☐
Means of communication available? (Mobile, radio etc.) ☐ ☐ ☐
Safe access / Working Platform provided? ☐ ☐ ☐
Mandatory/specific good condition PPEs are available ☐ ☐ ☐
Availability of barricades/protection to prevent unauthorized or accidental entry? ☐ ☐ ☐
Life Line provided? ☐ ☐ ☐
Warning signs posted? ☐ ☐ ☐
Fall Protection equipment (e.g. full body harness) available? ☐ ☐ ☐
Availability of Fall protection arrangement? ☐ ☐ ☐
Other(s): ☐ ☐ ☐
Adequate Lighting provided? ☐ ☐ ☐
☐ ☐ ☐
4. Acknowledgement by Initiator and Evaluator:
☐ Acknowledge that all above precautions have been taken. These have also been fully explained to the operatives, and I consider them competent to do it safely.
Initiator/Originator Name: Designation:
Signature: Time:
☐ Acknowledge that I have checked above control measures and consider the work area safe to carry out the activity
Evaluator (HSE Team): Designation:
Signature: Time
Comments (if any):
5. Authorization (PM/CM):
Name: Designation:
Signature: Time:
6. Completion/Cancelation of Permit:
☐ Acknowledge that the area have been restored to a safe and orderly condition.
Initiator Signature: Time:
☐ Acknowledge that I have checked the area and been restored to a safe and orderly condition.
Evaluator Signature: Time:
LIVE ELECTRICAL WORK PERMIT Form # HSEQ - LEP Rev 2.docx
1. Project Information: (To be filled by initiator/originator)
Project Name: Permit No.:
Project Location:
Requesting Contractor/Company
2. Permit Issuance Details: (To be filled by initiator/originator)
THIS PERMIT IS ONLY FOR ONE SHIFT AND NOT EXTENDABLE
Description of Task:
Location / Area :
Panel No : Voltage:
Permit Validity:
Time (from): _______Hrs.
Time (To): __________Hrs.
Date:
3. Prerequisites: (To be filled by initiator/originator and verified by Evaluator)
No: Checks Yes-No-NA Checks Yes-No-NA
ENERGIZATION (“Power On”) ISOLATION (“Power Off”)
1. Safety tool box briefing done. ☐ ☐ ☐
Method statement/Risk assessment in place. ☐ ☐ ☐
2. Authorized personnel / operators available. ☐ ☐ ☐
Authorized personnel / operators available. ☐ ☐ ☐
3. Method statement/Risk assessment in place. ☐ ☐ ☐
Adjacent live areas protected. ☐ ☐ ☐
4. Safety Barriers in place and safety signage Displayed. ☐ ☐ ☐
PPE available, high voltage rubber gloves, Safety goggles and floor mat. ☐ ☐ ☐
5. Working area is well lighted. ☐ ☐ ☐
Isolation/Lock-out in place. ☐ ☐ ☐
6. Electrical instruments are available for any Purpose. ☐ ☐ ☐
Electrical circuits “proved” by calibrated Instrument and found out to be no power. ☐ ☐ ☐
7. Correct PPE available, high voltage rubber Gloves, safety goggles and floor mat. ☐ ☐ ☐
Unauthorized workers are cleared from the Area. ☐ ☐ ☐
8. Approved WIR for installation, testing and Termination are attached to the permit. ☐ ☐ ☐
Standby operatives in the event of contact With live circuits. ☐ ☐ ☐
9. Emergency light (Flashlight) available. ☐ ☐ ☐
Emergency light (Flashlight) available. ☐ ☐ ☐
10. Is live work absolutely necessary? ☐ ☐ ☐
Emergency response plan available ☐ ☐ ☐
11. Unauthorized workers are cleared from the area.
☐ ☐ ☐
Other ( Specify): ☒ ☐ ☐
12. Power cable route from panel board to plant & equipment has been checked ☐ ☐ ☐
13 Emergency response plan available ☐ ☐ ☐
14 Other ( Specify): ☐ ☐ ☐
4. Acknowledgement by Initiator and Evaluator:
☐ Acknowledge that all above precautions have been taken. These have also been fully explained to the operatives, and I consider them competent to do it safely.
Initiator/Originator Name: Designation:
Signature: Date /Time:
☐ Acknowledge that I have checked above control measures and consider the work area safe to carry out the activity
Evaluator (HSE Team): Designation:
Signature: Date /Time
Comments (if any):
5. Authorization (PM/CM):
Name: Designation:
Signature: Date /Time:
6. Completion/Cancelation of Permit:
☐ Acknowledge that the area have been restored to a safe and orderly condition.
Initiator Signature: Time:
☐ Acknowledge that I have checked the area and been restored to a safe and orderly condition.
Evaluator Signature: Time:
MOBILE PLANT REGISTER Form # HSEQ - MPR Rev 3.docx
Project Information
Project Name:
Date: Location:
Sr. Equipment type / Name Registration No & Exp Date Company Name
Operator Name / Mb. No Operator Third party competency certificate expiry date Operator License expiry date Equipment & Plant 3rd Party Inspection Certificate expiry date SWL / Capacity Signalman /Rigger name & TPC Exp Comment
1
2
3
4
5
6
7
8
9
10.
Remarks:
Inspected By: Signature:
Reviewed By HSE Manager / In charge: Signature:
LABOR ACCOMMODATION CHECKLIST Form # HSEQ - LAC Rev 2.docx
This 5-page document is a checklist for inspecting labour accommodation on a weekly basis. It contains over 100 questions across various categories including access/egress, housekeeping, septic tanks, food preparation, living quarters, firefighting, emergency procedures, first aid, record keeping, environment, and civil defence requirements. Inspectors are to verify that accommodation meets standards for safety, sanitation, emergency preparedness and regulatory compliance by completing the checklist and noting any needed corrective actions or due dates.
INCIDENT INVESTIGATION REPORT Form # HSEQ - IIR Rev 9 -.docx
INCIDENT INVESTIGATION REPORT
(To be submitted to the HSEQ Corporate Office within 7 days of incident.)
1. Project Information:
Project Name: Click here to enter text.
Report No.: Click here to enter text.
Project Location: Click here to enter text.
Property No.: Click here to enter text.
☐ Fatality ☐ Major Incident ☐ Minor Incident
2. Describe the Incident in detail:
Answer who, what, why, where, when & how in this section: (Attach additional pages if required)
Click here to enter text.
☐ Photos Attached
3. Incident Root Causes:
Describe direct, indirect & root cause: (Attach additional pages if required)
Click here to enter text.
4. Key Corrective Actions to Prevent Recurrence:
Describe the corrective actions with timeframe: (Attach additional pages if required)
Click here to enter text.
5. Key Corrections Taken Immediately after the Incident:
Attach additional pages if more space is required:
Click here to enter text.
6. Witnesses:
I declare that I witnessed the incident and the information provided above is true, correct and complete.
No. Name Designation Signature Date
1. Click here to enter text.
Click here to enter text.
Click here to enter text.
2. Click here to enter text.
Click here to enter text.
Click here to enter text.
7. Incident Information:
Initial Incident Report No.: Click here to enter text.
Date Reported: Click here to enter text.
Date of Incident: Click here to enter text.
Time of Incident: Click here to enter text.
Type of Incident: ☐ Near Miss
☐ Major Environmental Incident
☐ Serious Dangerous Occurrence
☐ Equipment / Property Damage
☐ Medical Treatment Case (MTC)
☐ Restricted Work Case (RWC)
☐ Lost Workday Case (LWC)
☐ Serious Occupational Illness/Disease
☐ Class 1 Injuries
☐ Permanent Partial Disability (PPD)
☐ Permanent Total Disability (PTD)
☐ Fatality (F)
Recordkeeping: ☐ Reportable ☐ Recordable
Incident Location on Site: Click here to enter text.
Applicable Reports: ☐ Police
☐ Medical
☐ Other (Specify)
Click here to enter text.
Attached: ☐ Yes ☐ No
☐ Yes ☐ No
☐ Yes ☐ No
8. Injured Person’s Personal Details:
In case of an incident with more than one injured person, complete the information for each person using separate forms.
Name: Click here to enter text.
Occupation: Click here to enter text.
Company: Click here to enter text.
MB / Oracle No.: Click here to enter text.
Nationality: Click here to enter text.
Date of Birth: Click here to enter text.
Passport Number: Click here to enter text.
Length of Service: Click here to enter text.
Gender: ☐ Male ☐ Female
Labour Card No.: Click here to enter text.
9. Incident Causes Details: To be supported with factual evidence
Immediate Cause
(Unsafe Acts) ☐ Failure to secure
☐ Failure to warn
☐ Removing / Defeating Safety Devices
☐
HSE INDUCTION Form # HSEQ - HSEI Rev 2 -.doc
HSE INDUCTION
(Workers)
Name: _________________________________ Trade: ____________________________
M.B. No./Company Name : ________________
Date of Joining: __________________________
SL. N SUBJECT ON INDUCTION PREVIOUS SAFETY EXPOSURE FURTHER SAFETY TRAINING NEED ANALYSIS
1. Introduction Safety Requirements
2. Working Safety is of Primary Importance
3. General Safety Rules
4. Basic Safety Requirements
5. House Keeping
6. Health, Hygiene & Welfare Facilities
7. Fire Extinguisher / Fire Fighting
8. Emergency Procedure
9. Safety Violations & Penalty
10. Safety Award
11. Manual Handling
Induction Given By: Name: ___________________________
Designation: ___________________________
HSE WARNING LETTER-DISCIPLINARY NOTICE Form # HSEQ - HSEWL Rev 6.doc
1st Warning 0 Ref. No. ______________
2nd Warning 0
3rd Warning 0
4th Warning 0 Date: ________________
Employee’s Name : ______________________________________ M.B No. : __________
Occupation : _____________________________________________________________________
Location / Project Site: _____________________________________________________________________
You have committed the following HSE violation/s:
………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………….….
The employee is hereby warned that if the violation is repeated further disciplinary action can be
taken as per the company Code of Conduct.
ORIGINATOR APPROVED BY (MANAGER IN CHARGE / ARABTEC HSEQ & ORG. RISK Manager)
Name: _______________________________ Name: _____________________________
Designation: _______________________________ Designation: _____________________________
Signature:
_______________________________ Signature:
_____________________________
Employee Acknowledgement:
I the undersigned have received this Safety warning letter / disciplinary notice and I admit that I have understood the contents.
0 Received on: ………………………….. (Date) Signature: ………………………………..…..
OFFICE PORTA CABIN INSPECTION Form # HSEQ - OPC Rev 2.docx
Project Information
Project Name: Porta Cabin No:
Location: Contact Person:
Company Name: Date :
Sr. Description Yes No N/A Comments
1. Emergency exit signs are available in right locations
2. Fire alarms and fire extinguishers are visible and accessible.
3. Fire doors (e.g. in stairways) are kept closed unless equipped with automatic closing device
4. Fire extinguishers are serviced regularly
5. Corridors and stairways are kept free of obstruction
6. Fire escape/ evacuation plan available and posted
7. First aid box available
8. Floor surfaces are kept dry and free of slip hazards
9. Electrical cords and plugs are in good condition with proper Grounding
10. Kitchen equipment checked
11. Fire blanket available in the pantry
12. Heat detector available in the pantry
13. Toilets floor clean and dry
14. Are staff trained to use Fire Extinguishers
15. Hand wash/ soap solution available in the toilet
16. Civil Defense or Authority approval
17. Others if any:
Remarks:
Inspected By: Signature:
Reviewed By HSE Manager / In charge : Signature:
More from Dwarika Bhushan Sharma (20)
5 - CLOWNS BELONG IN THE CIRCUS & NOT ON THE JOB.pdf
5 - CLOWNS BELONG IN THE CIRCUS & NOT ON THE JOB.pdf
2-THERE'S A SAFE WAY TO DO EVERY JOB, OF YOU DON'T KNOW ASK.pdf
2-THERE'S A SAFE WAY TO DO EVERY JOB, OF YOU DON'T KNOW ASK.pdf
FIRE PREVENTION REQUIREMENTS Form # HSEQ - Rev 2.docx
FIRE PREVENTION REQUIREMENTS Form # HSEQ - Rev 2.docx
SUB CONTRACTORS HSE CHECKLIST Form # HSEQ - SPSC Rev 2 -.docx
SUB CONTRACTORS HSE CHECKLIST Form # HSEQ - SPSC Rev 2 -.docx
PROJECT LEADER INCIDENT BRIEFING Form # HSEQ - PLIB Rev 2 -.docx
PROJECT LEADER INCIDENT BRIEFING Form # HSEQ - PLIB Rev 2 -.docx
LIFT SHAFT ENTRY PERMIT Form # HSEQ - LSEP Rev 2 -.docx
LIFT SHAFT ENTRY PERMIT Form # HSEQ - LSEP Rev 2 -.docx
LIVE ELECTRICAL WORK PERMIT Form # HSEQ - LEP Rev 2.docx
LIVE ELECTRICAL WORK PERMIT Form # HSEQ - LEP Rev 2.docx
MOBILE PLANT REGISTER Form # HSEQ - MPR Rev 3.docx
MOBILE PLANT REGISTER Form # HSEQ - MPR Rev 3.docx
LABOR ACCOMMODATION CHECKLIST Form # HSEQ - LAC Rev 2.docx
LABOR ACCOMMODATION CHECKLIST Form # HSEQ - LAC Rev 2.docx
INCIDENT INVESTIGATION REPORT Form # HSEQ - IIR Rev 9 -.docx
INCIDENT INVESTIGATION REPORT Form # HSEQ - IIR Rev 9 -.docx
HSE WARNING LETTER-DISCIPLINARY NOTICE Form # HSEQ - HSEWL Rev 6.doc
HSE WARNING LETTER-DISCIPLINARY NOTICE Form # HSEQ - HSEWL Rev 6.doc
OFFICE PORTA CABIN INSPECTION Form # HSEQ - OPC Rev 2.docx
OFFICE PORTA CABIN INSPECTION Form # HSEQ - OPC Rev 2.docx
Recently uploaded
South African Journal of Science: Writing with integrity workshop (2024)
South African Journal of Science: Writing with integrity workshop (2024)Academy of Science of South Africa
A workshop hosted by the South African Journal of Science aimed at postgraduate students and early career researchers with little or no experience in writing and publishing journal articles.The History of Stoke Newington Street Names
Presented at the Stoke Newington Literary Festival on 9th June 2024
www.StokeNewingtonHistory.com
Your Skill Boost Masterclass: Strategies for Effective Upskilling
Your Skill Boost Masterclass: Strategies for Effective UpskillingExcellence Foundation for South Sudan
Strategies for Effective Upskilling is a presentation by Chinwendu Peace in a Your Skill Boost Masterclass organisation by the Excellence Foundation for South Sudan on 08th and 09th June 2024 from 1 PM to 3 PM on each day.Executive Directors Chat Leveraging AI for Diversity, Equity, and Inclusion
Let’s explore the intersection of technology and equity in the final session of our DEI series. Discover how AI tools, like ChatGPT, can be used to support and enhance your nonprofit's DEI initiatives. Participants will gain insights into practical AI applications and get tips for leveraging technology to advance their DEI goals.
Chapter 4 - Islamic Financial Institutions in Malaysia.pptx
Chapter 4 - Islamic Financial Institutions in Malaysia.pptxMohd Adib Abd Muin, Senior Lecturer at Universiti Utara Malaysia
This slide is special for master students (MIBS & MIFB) in UUM. Also useful for readers who are interested in the topic of contemporary Islamic banking.
clinical examination of hip joint (1).pdf
described clinical examination all orthopeadic conditions .
Pengantar Penggunaan Flutter - Dart programming language1.pptx
Pengantar Penggunaan Flutter - Dart programming language1.pptx
Azure Interview Questions and Answers PDF By ScholarHat
Azure Interview Questions and Answers PDF By ScholarHat
How to Build a Module in Odoo 17 Using the Scaffold Method
Odoo provides an option for creating a module by using a single line command. By using this command the user can make a whole structure of a module. It is very easy for a beginner to make a module. There is no need to make each file manually. This slide will show how to create a module using the scaffold method.
Pollock and Snow "DEIA in the Scholarly Landscape, Session One: Setting Expec...
Pollock and Snow "DEIA in the Scholarly Landscape, Session One: Setting Expec...National Information Standards Organization (NISO)
This presentation was provided by Steph Pollock of The American Psychological Association’s Journals Program, and Damita Snow, of The American Society of Civil Engineers (ASCE), for the initial session of NISO's 2024 Training Series "DEIA in the Scholarly Landscape." Session One: 'Setting Expectations: a DEIA Primer,' was held June 6, 2024.Main Java[All of the Base Concepts}.docx
This is part 1 of my Java Learning Journey. This Contains Custom methods, classes, constructors, packages, multithreading , try- catch block, finally block and more.
Community pharmacy- Social and preventive pharmacy UNIT 5
Covered community pharmacy topic of the subject Social and preventive pharmacy for Diploma and Bachelor of pharmacy
PCOS corelations and management through Ayurveda.
This presentation includes basic of PCOS their pathology and treatment and also Ayurveda correlation of PCOS and Ayurvedic line of treatment mentioned in classics.
RPMS TEMPLATE FOR SCHOOL YEAR 2023-2024 FOR TEACHER 1 TO TEACHER 3
RPMS Template 2023-2024 by: Irene S. Rueco
Recently uploaded (20)
South African Journal of Science: Writing with integrity workshop (2024)
South African Journal of Science: Writing with integrity workshop (2024)
Pride Month Slides 2024 David Douglas School District
Pride Month Slides 2024 David Douglas School District
Your Skill Boost Masterclass: Strategies for Effective Upskilling
Your Skill Boost Masterclass: Strategies for Effective Upskilling
Executive Directors Chat Leveraging AI for Diversity, Equity, and Inclusion
Executive Directors Chat Leveraging AI for Diversity, Equity, and Inclusion
Film vocab for eal 3 students: Australia the movie
Film vocab for eal 3 students: Australia the movie
Chapter 4 - Islamic Financial Institutions in Malaysia.pptx
Chapter 4 - Islamic Financial Institutions in Malaysia.pptx
Pengantar Penggunaan Flutter - Dart programming language1.pptx
Pengantar Penggunaan Flutter - Dart programming language1.pptx
Azure Interview Questions and Answers PDF By ScholarHat
Azure Interview Questions and Answers PDF By ScholarHat
How to Build a Module in Odoo 17 Using the Scaffold Method
How to Build a Module in Odoo 17 Using the Scaffold Method
Pollock and Snow "DEIA in the Scholarly Landscape, Session One: Setting Expec...
Pollock and Snow "DEIA in the Scholarly Landscape, Session One: Setting Expec...
Liberal Approach to the Study of Indian Politics.pdf
Liberal Approach to the Study of Indian Politics.pdf
Community pharmacy- Social and preventive pharmacy UNIT 5
Community pharmacy- Social and preventive pharmacy UNIT 5
RPMS TEMPLATE FOR SCHOOL YEAR 2023-2024 FOR TEACHER 1 TO TEACHER 3
RPMS TEMPLATE FOR SCHOOL YEAR 2023-2024 FOR TEACHER 1 TO TEACHER 3
10 Ways to Prevent ARC Welding Injury
- 1. Do not touch the electrode or metal parts of the electrode holder with skin or wet clothing. Always use proper Personal Protective Equipment (PPE) when welding. Arc welding is safe if the unit is properly installed and used. You can receive a shock, however, from the primary (input) voltage if you touch a lead or other electrically "hot" component inside the welder while any part of your body brushes the welder case or other grounded metal. If properly installed and used, the arc welder is very safe. If used improperly, the unit can expose welders to fire, explosion, and retinal burns. 10 Ways to Prevent ARC Welding Injury Safe Work Practices and Tips: Inspect the arc welder before starting any operation, Remove all potential fire hazards from the welding area for at least 35 feet and Read all warning labels and instruction manuals for the welder. Use fire tarps to prevent sparks coming in contact with flammable or combustible materials or liquids Have a fire extinguisher ready for immediate use and Don't strike an arc without proper eye protection. Look for frayed welding leads and any damage to the welder and Insulate your body from the metal you are welding. Ground the welder case so that if a problem develops inside the welder a fuse will blow, disconnecting the power and letting you know that repair is required. Do not rest your body, arms, or legs on the work piece, especially if your clothing is wet or bare skin is exposed. Use mats of plywood, rubber or some other dry insulation to stand or lie upon. Wear dry gloves in good condition when welding. “WORKERS LIVES MATTER” 1 2 3 4 5 6 7 Do not watch Arc Welding at work with out protection may cause “Blindness” 8 9 10