This document discusses various methods for water softening and treatment. It describes the lime soda process, which uses lime and soda to chemically convert hardness-causing salts into insoluble precipitates. The cold and hot lime soda processes are compared. Other methods discussed include zeolite/permutit ion exchange process and demineralization/deionization using cation and anion exchange resins to remove ions responsible for hardness. Details are provided on the chemical reactions, equipment used, advantages and limitations of each process.
This presentation is about cooling tower & cooing water treatment & cooing water problems. In the end the presentation can able to understand about operation & monitoring of cooling water.
Water treatment procedure also vary depending upon its use. However, overall picture of water treatment, irrespective of end use shall be considered. An endeavor is made to comprehend the basic chemistry involved in water treatment process. The important stages involved in treatment are as follows: coagulation or flocculation; sedimentation; filtration – slow sand, rapid sand filtration; disinfection – including chlorination and ozonolysis; removal of iron and manganese; softening by lime-soda ash process or deionization method; scale and corrosion control; taste and odor removal; prophylaxiation treatment, i.e., fluoridisation; and specialized treatment for a specific purpose.
This presentation is about cooling tower & cooing water treatment & cooing water problems. In the end the presentation can able to understand about operation & monitoring of cooling water.
Water treatment procedure also vary depending upon its use. However, overall picture of water treatment, irrespective of end use shall be considered. An endeavor is made to comprehend the basic chemistry involved in water treatment process. The important stages involved in treatment are as follows: coagulation or flocculation; sedimentation; filtration – slow sand, rapid sand filtration; disinfection – including chlorination and ozonolysis; removal of iron and manganese; softening by lime-soda ash process or deionization method; scale and corrosion control; taste and odor removal; prophylaxiation treatment, i.e., fluoridisation; and specialized treatment for a specific purpose.
Soft, hard and heavy water, by Saliha Rais, for grade 9.Saliha Rais
The slide show includes the following topics:
1. hard water
2. soft water
3. causes of hardness of water
4. types of hardness (temporary and permanent)
5. methods to remove temporary hardness (heating and clarks method)
6. methods to remove permanent hardness (with washing soda, caustic soda and zeolite)
7. Heavy water
8. hygroscopic and deliquescent substances
I have made this presentation for grade 9 students.
Electro-oxidation And Its Feasibility In Wastewater TreatmentSakib Shahriar
Electro-oxidation (EO) is one of the advanced oxidation processes (AOP) used in wastewater treatment. It is also called anodic oxidation. In this presentation, we can learn about the working principle, industrial applications, types of electrodes, and catalysts in the EO process. The advantages and disadvantages are described later. The main advantages of electro-oxidation are the formation of low sludge and large percentages of organic matter degradation. But the main drawbacks occur due to the requirement of large space and expense. EO is used in many types of wastewater treatment. Degradation of methyl orange azo dye in a recirculation flow plant system, treatment of wastewater containing aromatic amines, endocrine disruptors treatment, domestic water, industrial wastewater, synthetic dye effluent, olive mill wastewater, pulp mill wastewater, citric acid wastewater.
3 modren sodium hydroxide manufacturing methodsrita martin
Sodium hydroxide also known as caustic soda with chemical formula NaOH found in many forms caustic soda lye, flakes, granules and solid. Produced using three different process Mercury Cell, Diaphragm cell, Membrane Cell methods
Soft, hard and heavy water, by Saliha Rais, for grade 9.Saliha Rais
The slide show includes the following topics:
1. hard water
2. soft water
3. causes of hardness of water
4. types of hardness (temporary and permanent)
5. methods to remove temporary hardness (heating and clarks method)
6. methods to remove permanent hardness (with washing soda, caustic soda and zeolite)
7. Heavy water
8. hygroscopic and deliquescent substances
I have made this presentation for grade 9 students.
Electro-oxidation And Its Feasibility In Wastewater TreatmentSakib Shahriar
Electro-oxidation (EO) is one of the advanced oxidation processes (AOP) used in wastewater treatment. It is also called anodic oxidation. In this presentation, we can learn about the working principle, industrial applications, types of electrodes, and catalysts in the EO process. The advantages and disadvantages are described later. The main advantages of electro-oxidation are the formation of low sludge and large percentages of organic matter degradation. But the main drawbacks occur due to the requirement of large space and expense. EO is used in many types of wastewater treatment. Degradation of methyl orange azo dye in a recirculation flow plant system, treatment of wastewater containing aromatic amines, endocrine disruptors treatment, domestic water, industrial wastewater, synthetic dye effluent, olive mill wastewater, pulp mill wastewater, citric acid wastewater.
3 modren sodium hydroxide manufacturing methodsrita martin
Sodium hydroxide also known as caustic soda with chemical formula NaOH found in many forms caustic soda lye, flakes, granules and solid. Produced using three different process Mercury Cell, Diaphragm cell, Membrane Cell methods
Treatment of water for domestic use,Screening,Sedimentation,Co-agulation,Filtration,Disinfection of water,Water softening
Permutit Process,Ion exchange method,Mixed bed Dimneralisation process, Lime- Soda process ,Desalination
RO Method, Electrodialysis
Immunizing Image Classifiers Against Localized Adversary Attacksgerogepatton
This paper addresses the vulnerability of deep learning models, particularly convolutional neural networks
(CNN)s, to adversarial attacks and presents a proactive training technique designed to counter them. We
introduce a novel volumization algorithm, which transforms 2D images into 3D volumetric representations.
When combined with 3D convolution and deep curriculum learning optimization (CLO), itsignificantly improves
the immunity of models against localized universal attacks by up to 40%. We evaluate our proposed approach
using contemporary CNN architectures and the modified Canadian Institute for Advanced Research (CIFAR-10
and CIFAR-100) and ImageNet Large Scale Visual Recognition Challenge (ILSVRC12) datasets, showcasing
accuracy improvements over previous techniques. The results indicate that the combination of the volumetric
input and curriculum learning holds significant promise for mitigating adversarial attacks without necessitating
adversary training.
Student information management system project report ii.pdfKamal Acharya
Our project explains about the student management. This project mainly explains the various actions related to student details. This project shows some ease in adding, editing and deleting the student details. It also provides a less time consuming process for viewing, adding, editing and deleting the marks of the students.
Event Management System Vb Net Project Report.pdfKamal Acharya
In present era, the scopes of information technology growing with a very fast .We do not see any are untouched from this industry. The scope of information technology has become wider includes: Business and industry. Household Business, Communication, Education, Entertainment, Science, Medicine, Engineering, Distance Learning, Weather Forecasting. Carrier Searching and so on.
My project named “Event Management System” is software that store and maintained all events coordinated in college. It also helpful to print related reports. My project will help to record the events coordinated by faculties with their Name, Event subject, date & details in an efficient & effective ways.
In my system we have to make a system by which a user can record all events coordinated by a particular faculty. In our proposed system some more featured are added which differs it from the existing system such as security.
Automobile Management System Project Report.pdfKamal Acharya
The proposed project is developed to manage the automobile in the automobile dealer company. The main module in this project is login, automobile management, customer management, sales, complaints and reports. The first module is the login. The automobile showroom owner should login to the project for usage. The username and password are verified and if it is correct, next form opens. If the username and password are not correct, it shows the error message.
When a customer search for a automobile, if the automobile is available, they will be taken to a page that shows the details of the automobile including automobile name, automobile ID, quantity, price etc. “Automobile Management System” is useful for maintaining automobiles, customers effectively and hence helps for establishing good relation between customer and automobile organization. It contains various customized modules for effectively maintaining automobiles and stock information accurately and safely.
When the automobile is sold to the customer, stock will be reduced automatically. When a new purchase is made, stock will be increased automatically. While selecting automobiles for sale, the proposed software will automatically check for total number of available stock of that particular item, if the total stock of that particular item is less than 5, software will notify the user to purchase the particular item.
Also when the user tries to sale items which are not in stock, the system will prompt the user that the stock is not enough. Customers of this system can search for a automobile; can purchase a automobile easily by selecting fast. On the other hand the stock of automobiles can be maintained perfectly by the automobile shop manager overcoming the drawbacks of existing system.
About
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.
Technical Specifications
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
Key Features
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface
• Compatible with MAFI CCR system
• Copatiable with IDM8000 CCR
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
Application
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.
Hybrid optimization of pumped hydro system and solar- Engr. Abdul-Azeez.pdffxintegritypublishin
Advancements in technology unveil a myriad of electrical and electronic breakthroughs geared towards efficiently harnessing limited resources to meet human energy demands. The optimization of hybrid solar PV panels and pumped hydro energy supply systems plays a pivotal role in utilizing natural resources effectively. This initiative not only benefits humanity but also fosters environmental sustainability. The study investigated the design optimization of these hybrid systems, focusing on understanding solar radiation patterns, identifying geographical influences on solar radiation, formulating a mathematical model for system optimization, and determining the optimal configuration of PV panels and pumped hydro storage. Through a comparative analysis approach and eight weeks of data collection, the study addressed key research questions related to solar radiation patterns and optimal system design. The findings highlighted regions with heightened solar radiation levels, showcasing substantial potential for power generation and emphasizing the system's efficiency. Optimizing system design significantly boosted power generation, promoted renewable energy utilization, and enhanced energy storage capacity. The study underscored the benefits of optimizing hybrid solar PV panels and pumped hydro energy supply systems for sustainable energy usage. Optimizing the design of solar PV panels and pumped hydro energy supply systems as examined across diverse climatic conditions in a developing country, not only enhances power generation but also improves the integration of renewable energy sources and boosts energy storage capacities, particularly beneficial for less economically prosperous regions. Additionally, the study provides valuable insights for advancing energy research in economically viable areas. Recommendations included conducting site-specific assessments, utilizing advanced modeling tools, implementing regular maintenance protocols, and enhancing communication among system components.
Welcome to WIPAC Monthly the magazine brought to you by the LinkedIn Group Water Industry Process Automation & Control.
In this month's edition, along with this month's industry news to celebrate the 13 years since the group was created we have articles including
A case study of the used of Advanced Process Control at the Wastewater Treatment works at Lleida in Spain
A look back on an article on smart wastewater networks in order to see how the industry has measured up in the interim around the adoption of Digital Transformation in the Water Industry.
Democratizing Fuzzing at Scale by Abhishek Aryaabh.arya
Presented at NUS: Fuzzing and Software Security Summer School 2024
This keynote talks about the democratization of fuzzing at scale, highlighting the collaboration between open source communities, academia, and industry to advance the field of fuzzing. It delves into the history of fuzzing, the development of scalable fuzzing platforms, and the empowerment of community-driven research. The talk will further discuss recent advancements leveraging AI/ML and offer insights into the future evolution of the fuzzing landscape.
TECHNICAL TRAINING MANUAL GENERAL FAMILIARIZATION COURSEDuvanRamosGarzon1
AIRCRAFT GENERAL
The Single Aisle is the most advanced family aircraft in service today, with fly-by-wire flight controls.
The A318, A319, A320 and A321 are twin-engine subsonic medium range aircraft.
The family offers a choice of engines
COLLEGE BUS MANAGEMENT SYSTEM PROJECT REPORT.pdfKamal Acharya
The College Bus Management system is completely developed by Visual Basic .NET Version. The application is connect with most secured database language MS SQL Server. The application is develop by using best combination of front-end and back-end languages. The application is totally design like flat user interface. This flat user interface is more attractive user interface in 2017. The application is gives more important to the system functionality. The application is to manage the student’s details, driver’s details, bus details, bus route details, bus fees details and more. The application has only one unit for admin. The admin can manage the entire application. The admin can login into the application by using username and password of the admin. The application is develop for big and small colleges. It is more user friendly for non-computer person. Even they can easily learn how to manage the application within hours. The application is more secure by the admin. The system will give an effective output for the VB.Net and SQL Server given as input to the system. The compiled java program given as input to the system, after scanning the program will generate different reports. The application generates the report for users. The admin can view and download the report of the data. The application deliver the excel format reports. Because, excel formatted reports is very easy to understand the income and expense of the college bus. This application is mainly develop for windows operating system users. In 2017, 73% of people enterprises are using windows operating system. So the application will easily install for all the windows operating system users. The application-developed size is very low. The application consumes very low space in disk. Therefore, the user can allocate very minimum local disk space for this application.
1. Water Treatment & Analysis 1
WATER TREATMENT AND ANALYSIS
UNIT-II
2.1 Water Softening Methods - Clark’s process - Lime soda process - Modified lime soda process
- Permutit or Zeolite process - Ion exchange process - Demineralization of water.
2.2 Determination of Hardness of water - Titration method - Complexometric method using
EDTA - Expressing Hardness.
2.3 Equivalents of Calcium Carbonate - Problems to determine Temporary and Permanent
Hardness.
2. Water Treatment & Analysis 2
WATER SOFTENING METHODS
Softening of Water
Water used for industrial purposes should be pure. ie., It should be free from hardness, scale
forming substances and corrosive agents like dissolved O2 etc., The process of removing hardness
producing salts from water is known as softening of water.
CLARK 'S PROCESS
It is the process of liming hard water. It is used to decreases the alkalinity of water. During
lime treatment the following reactions occur.
HCO3
-
+ OH-
CO3
2-
+ H2O
Ca2+
+ CO3
2-
CaCO3
Mg2+
+ 2OH-
Mg (OH)2
CO2 + 2OH-
CO3
2-
+ H2O
Softening of Water can be done by the following two ways
1. External conditioning or External treatment
2. Internal conditioning or Internal treatment.
EXTERNAL CONDITIONING
It involves the removal of hardness producing salts from the water before feeding into the
boiler. The external treatment can be done by the following methods.
a) Lime soda process
b) Zeolite (or Permutit process
c) Demineralisation (or) Deionization.
The above said processes are the examples of ionexchange process of water softening.
In an ion-exchange process, a reversible exchange of ions taking place between a stationary
solid phase and an external liquid mobile phase.
a) Lime-Soda Process
Lime-Soda process is a very important method used for the softening of water.
[i] Principle
The lime-soda process involves the chemical conversion of all the soluble hardness-
causing salts by the addition of soda and lime into insoluble precipitates which could easily be
removed by settling and filtration.
3. Water Treatment & Analysis 3
In this process, water to be softened is treated with calculated amounts of lime Ca(OH)2
and soda Na2CO3. For quick completion of reactions, the reagents may be used in 10 % excess.
The functions of lime and soda are as follows.
Functions of lime
Lime removes temporary hardness, permanent magnesium hardness,
dissolved iron and aluminium salts, dissolved CO2 and H2S gases and free mineral acids present
in water. The reactions involved are as follows 1. Removal of temporary calcium and magnesium
hardness
Ca (HCO3)2 + Ca (OH)2 2CaCO3 + 2H2O
Mg (HCO3)2 + 2Ca (OH)2 2CaCO3 + Mg (OH)2 + 2H2O
Removal of permanent magnesium hardness
MgCl2 + Ca (OH)2 Mg (OH)2 + CaCl2
MgSO4 + Ca (OH)2 Mg (OH)2 + CaSO4
Removal of dissolved iron and magnesium salts
Al2 (SO4)3 + 3 Ca (OH)2 2Al (OH)3 + 3CaSO4
FeSO4 + Ca (OH)2 Fe (OH)2 + CaSO4
2Fe (OH)2 + H2O + 1/2O2 2Fe (OH)3
Removal of dissolved CO2 and H2S
CO2 + Ca (OH)2 CaCO3 + H2O
H2S + Ca (OH)2 CaS + 2H2O
Removal of free mineral acid
2HCl + Ca (OH)2 CaCl2 + 2H2O
H2SO4 + Ca (OH)2 CaSO4 + 2H2O
Functions of soda
During the removal of Mg2+
, Fe2+
, Al3+
, HCl and H2SO4 by lime, permanent calcium
hardness is introduced in the water due to formation of calcium salts. The permanent calcium
hardness thus introduced on account of the treatment of water with lime and the permanent
calcium hardness already present in water before lime treatment are removed by soda. The
reactions involved are as follows,
CaCl2 + Na2CO3 CaCO3 + 2NaCl
CaSO4 + Na2CO3 CaCO3 + Na2SO4
4. Water Treatment & Analysis 4
The chemical reactions involved in the lime-soda process are quite slow. Moreover, the
precipitates formed [particularly of CaCO3 and Mg(OH)2] are fine and have a tendency to form
super-saturated solutions. This results in after deposition of these precipitates later in the pipes
and boiler tubes leading to their clogging and corrosion. These drawbacks of the process can be
overcome by
o thorough mixing of chemicals and water.
o allowing proper time for the completion of reactions.
o the use of accelerators such as active charcoal and
o the use of coagulants such as alum or NaAlO2.
[ii] Process
The lime-soda process can be carried out both at room temperature as well as at higher
temperatures. The process carried out at room temperature is called cold lime –soda process and
that carried out at 94°-100°C is called hot lime-soda process.
1. Cold Lime-Soda Process
In this method, water to be softened is treated with calculated quantities of lime and soda
at room temperature. Small amounts of a coagulant such as alum, aluminium sulphate, sodium
aluminate etc., are also added.
The coagulant helps the finely divided precipitate formed in the process to flocculate.
Sodium aluminate also helps in the removal of silica and oil present in water.
Method
The mixture of water, calculated quantities of lime and soda and a small amount of a
coagulant is fed from the top into inner chamber of a vertical circular tank (Fig.1).
The chamber is provided with a vertical rotating shaft carrying a number of paddles to
ensure vigorous stirring and continuous mixing of water with the chemicals added.
5. Water Treatment & Analysis 5
Fig 1 Cold Lime-Soda Process
The chemical reactions take place and the hardness producing salts get converted into
insoluble precipitates which accumulate in the form of a heavy sludge.
As the softened water reaches the outer coaxial chamber, it rises upwards and is filtered
by a wood-fibre filter and finally taken out from an outlet provided at the top of the outer cylinder.
The heavy sludge settles down at the bottom of the outer chamber and is taken out through
an outlet. The softened water obtained from this process contains a residual hardness of about 50-
60 ppm.
2. Hot Lime-Soda Process
In this process, water is treated with the softening chemicals at a temperature of 94°-100°C.
Since the process is carried out at a temperature close to the boiling point of the solution, the
reaction proceeds faster and the softening capacity of the process increases several times.
6. Water Treatment & Analysis 6
Fig.2 Hot Lime-Soda Process
At this temperature, the viscosity of water is much less than that at room temperature.
Hence, rate of aggregation of particles increases and there is hardly any need of adding any
coagulant. Moreover, the dissolved gases also escape to some extent at the temperature of the
process.
Method
A typical hot lime-soda water softening plant is shown in
Fig.2. It consists of
a reaction tank
a conical sedimentation vessel and
a sand filter.
Raw water is fed from the top into the reaction tank where it is thoroughly mixed with
calculated quantities of softening chemicals and is agitated with superheated steam. The reactions
take place and water gets softened. The softened water containing sludge then enters into the
sedimentation vessel where sludge settles down.
The softened water rises up in the vessel, while precipitated sludge is taken out through an
outlet provided at the bottom of the vessel. The softened water is then taken to a sand filter which
ensures the complete removal of the sludge from softened water.
The softened water obtained from this process contains a residual hardness of 15-30 ppm.
Advantages of the process
The hot lime-soda process has the following advantages.
7. Water Treatment & Analysis 7
The process is much faster as compared to the cold sodalime process.
It is very economical.
Lesser amounts of coagulants are needed.
The process increases the pH value of the treated water, thereby reducing the corrosion of
distribution pipes.
To certain extent, iron and manganese are also removed from water.
Much of dissolved gases in water are also removed.
Due to an increase in the pH, the amount of pathogenic bacteria in treated water also gets
reduced.
Disadvantages of the process
The hot lime-soda process has the following disadvantages.
Disposal of large amounts of sludge formed in the process poses problems.
The treated water obtained by this process is not completely softened. It still contains a residual
hardness of about 15-30 ppm, which is not good for boilers.
Table 1.4 Difference between cold and hot lime soda process
Cold L-S Process Hot L-S Process
Done at room temperature.
Done near the boiling point of
water.
Reactions are slow and takes hours to
complete.
Fast and takes only 15 minutes.
Precipitate is finely divided and
therefore coagulants are needed.
Coarse precipitate coagulants not
needed.
Tank size is large. Small and compact.
Residual hardness 50 to 60 ppm. 15 to 30 ppm
Chemicals are consumed by dissolved
gas,CO2 etc.,
CO2 and temporary hardness are
automatically removed.
8. Water Treatment & Analysis 8
b) Zeolite (or) Permutit Process
Zeolites are naturally occuring hydrated sodium aluminium silicate, Na2O. Al2 O3. x SiO2
yH2O where x = 2 to 10 and y = 2 to 6. The synthetic form of zeolite is known as permutit.
Synthetic zeolite is represented by Na2Ze. The sodium ions which are loosely held in Na2Ze are
replaced by Ca2+
and Mg2+
ions present in the water. Natural zeolites are non-porous.
Synthetic zeolites are porous and gelly structure. They are prepared by heating together
china clay, feldspar and soda ash. These zeolites are higher exchange capacity per unit weight
than natural zeolites.
Process
In this process, the hard water is passed through a bed of sodium zeolite (Na2 Ze). The
hardness causing ions (Ca2+
, Mg2+
) in hard water is replaced by loosely held sodium ions in zeolite
bed(Fig.3.7). The outgoing soft water contains only sodium ions.
Na2Ze + Ca (HCO3)2 CaZe + 2NaHCO3
Na2Ze + Mg (HCO3)2 MgZe + 2NaHCO3
Na2Ze + CaCl2 CaZe + 2NaCl
Na2Ze + MgCl2 MgZe + 2NaCl
Na2Ze + CaSO4 CaZe + Na2SO4
Na2Ze + MgSO4 MgZe + Na2SO4
Fig. 3 Zeolite process
Regeneration
After the softening process, the zeolite is completely converted into calcium and
magnesium zeolites and it gets exhausted. At this stage the hard water supply is stopped and the
exhausted bed is regenerated by treating with a concentrated 10% brine (NaCl) solution.
9. Water Treatment & Analysis 9
CaZe + 2NaCl Na2Ze + CaCl2
MgZe + 2NaCl Na2Ze + MgCl2
Exhausted Regenerated
Zeolite Zeolite
Advantages of the process
This process removes hardness upto 10ppm.
Operational cost is less
The equipment used is compact No sludge formation.
The plant can be connected to water supply line as it avoids double pumping. Requires less
time for softening
Maintenance and operation is easy
The process automatically adjusts itself to waters of different hardness.
Limitations of the process
The process exchanges only Ca2+
and Mg2+
ions with Na+
ions. It does not remove the
acidic ions like HCO3
-
, CO3
2-
.
Water containing such ions is not much suitable for boilers as it may cause corrosion of
boilers. Turbid water, if used clogs the pores of the Zeolite bed, making it inactive.
Highly acidic or alkaline water will destroy the Zeolite bed.
Coloured ions (Fe2+
and Mn2+
) if present in water should be removed first and then the
water is sent to the bed, as these ions convert sodium Zeolite into their respective Zeolites
(FeZe, MnZe) which are difficult to be regenerated.
High capital cost
c) Demineralization (or) Deionization Process
In this method ion exchange resins are used as softening material.In this process cations
like Ca2+
, Mg2+
and anions like Cl-, SO4
2-
which are responsible for hardness are removed
respectively by cation exchange resins and anion exchange resins. Ion exchange resins are
insoluble, cross linked, long chain organic polymers with a micro porous structure. The functional
groups attached to the chains are responsible for the ionexchanging properties.
Cation exchange resins (RH+)
Resin containing acidic functional groups (-COOH, -SO3H) are capable of exchanging
their H+ ions with cations of hard water.
10. Water Treatment & Analysis 10
Example: (i) Sulphonated coals.
(ii) Sulphonated polystyrene.
R-SO3H ; R-COOH ≡ RH2
Anion exchange resins (ROH-
)
Resins containing basic functional groups (-NH2, -OH) are capable of exchanging their
OH- ions with the anions of hard water.
Example: (i) Cross-linked quaternary ammonium salts. (ii) Urea-formaldehyde resin
R-NR3OH ; R-OH ; R-NH2 ≡ R(OH)2
Process
The hard water first passed through a cation exchange column (Fig.1.8) which absorbs all
the cations like Ca2+
, Mg2+
, Na+
, K+
etc., present in the hard water.
2RH+
+ CaCl2 R2Ca + 2HCl
2RH+
+ MgSO4 R2Mg + H2SO4
RH+
+ NaCl RNa + HCl
Fig.4 Demineralisation process
The cation free water is then passed through an anion exchange column, which absorbs all
the anions like Cl-
, SO4
2-
etc., present in the water.
2ROH-
+ 2HCl 2RCl + 2H2O
2ROH-
+ H2SO4 R2SO4 + 2H2O
Thus the water coming out from the anion exchange is free from both cations and anions.
This water is known as ionfree water (or) deionised (or) demineralised water.
11. Water Treatment & Analysis 11
Regeneration
When the cation exchange column is exhausted, it can be regenerated by passing a solution
of dil.HCl (or) dil.H2 SO4.
R2Ca + 2HCl 2RH+
+ CaCl2
R2Mg + H2SO4 2RH+
+ MgSO4
RNa + HCl RH+
+ NaCl
When the anion exchange column is exhausted, it can be regenerated by passing a solution
of dil. NaOH.
2RCl + 2NaOH 2ROH-
+ 2NaCl
R2SO4 + 2NaOH 2ROH-
+ Na2SO4
Advantages
The process can be used to soften highly acidic (or) alkaline water.
It produces water of very low hardness (2ppm).
Disadvantages:
The equipment is costly and more expensive chemicals are needed.
If the water contains turbidity, the output is low due to clogging.
MIXED BED DEIONIZER
This comprises of a single cylinder. This contains a bed of intimate mixture of cation
exchanger resin and anion exchanger resin. When water is passed through this bed it comes in
contact many times with both cation and anion exchangers alternatively. The effect of mixed bed
exchanger is equivalent to passing through a series of several cation and anion exchangers
(multiple cycle). The outgoing water from the mixed bed contains even less than 1ppm of
dissolved salts.
Regeneration
When the resins are exhausted, the mixed bed is back washed by forcing water in the
upward direction. The lighter anion exchanger gets displaced to form an upper layer. The heavier
cation exchanger forms the lower layer. There after the anion exchanger is regenerated by passing
caustic soda solution from the top and then rinsed and reused. The lower cation exchanger bed is
then regenerated by passing sulphuric acid solution and rinsed and then reused. The two beds are
then mixed again by forcing compressed air. The bed is then reused.
12. Water Treatment & Analysis 12
Table 1.5 Comparison of Zeolite & Demineralization process
Zeolite (or) Permutit Process
Demineralization (or)
Deionization Process
It exchanges only cations.
Both the cation and anoin exchanges
are available.
Residual hardness 1-5 ppm. Residual hardness 0-2 ppm.
Cost of plant and material high. Cost higher.
Operating expenses are low. Operating expenses high.
Acidic water cannot be treated.
Even highly acidic or highly alkaline
water can be treated.
Treated water contains more dissolved
solids No dissolved solids.
Characteristics of Soft, Deionised and Distilled Water
Soft Water
It does not contain hardness producing ions like Ca2+
, Mg2+
It may contain Na+
, K+
, SO4
2-
, Cl-
ions and microorganisms.
Deionised water (mineral water)
It does not contain any ions including hardness producing cations.
It may contain some amount of micro-organisms.
Distilled Water
It does not contain any ions and micro-organisms, because it is prepared by condensing
the vapour of boiling water.
Hard Water
It contains all hardness producing ions.
Specification for Drinking water
The common specifications recommended by the US Public health for Drinking water are
given below.
Water should be clear and odourless.
13. Water Treatment & Analysis 13
It should be cool.
It should be pleasant to taste.
Turbiditiy of water should not exceed 10 ppm.
pH of the water should be in the range of 7.0 – 8.5.
Chloride and sulphate contents should be less than 250 ppm.
Total hardness of the water should be less than 500 ppm.
Total dissolved solids should be less than 500 ppm.
Fluoride content of the water should be less than 1.5 ppm.
The water must be free from disease producing bacteria.
Water should be free from objectionable dissolved gases like H2S.
Water should be free from objectionable minerals such as lead, chromium, manganese and
arsenic salts.
Estimation of Hardness of Water by EDTA Method
The hardness of water can be estimated by EDTA method. This is a reliable method because
of its greater accuracy. In this method hardness is estimated by forming complexes. EDTA is
Ethylene diamine tetra aceticacid.
Molecular structure of EDTA
HOOC-H2C CH2-COOH
N-CH2-CH2-N
HOOC-H2C CH2-COOH
In this complexometric method, disodium salt of ethylene diamine tetra acetic acid is actually
used.
Structure of disodium salt of EDTA
NaOOC-H2C CH2-COOH
N-CH2-CH2-N
HOOC-H2C CH2-COONa
14. Water Treatment & Analysis 14
Principle
1. Disodium salt of EDTA forms complex with calcium and magnesium ions present inwater.
2. The indicator used in this titration is Eriochrome Black-T (EBT) which also form unstable
complex with calcium and magnesium ions present in water, at pH value about8-10.
3. In order to maintain the pH, buffer solution [ NH4Cl-NH4OH] mixture is added. Only at this
pH such a complexation ispossible.
4. pH=8-10
Ca2+
/Mg2
+ EBT [Ca / Mg -EBT]
Indicator Unstable complex (Bluecolour)
(Wine red)
This wine red colour solution is titrated against EDTA, EDTA replaces EBT indicator from
[Ca / Mg - EBT] complex. The colour of the solution changes from wine red to steel blue at the
end point.
pH=8-10
[Ca / Mg - EBT]+EDTA [Ca / Mg - EDTA] + EBT
Unstablecomplex Stablecomplex (Steel blue)
(Winered) (Colorless)
Reagents Required :
1) EDTA solution
It is prepared by dissolving 4 gms of EDTA in 1000 ml of distilled water.
Standard hardwater
1 gm of pure CaCO3is dissolved in minimum quantity of HCl and then made upto 1000ml
using distilled water.
1 ml of standard hardwater=1mg of CaCO3equivalent hardness.
EBTindicator
0.5 gms of EBT is dissolved in 100 ml of alcohol.
Buffersolution:
67.5 gms of NH4Cl and 570 ml of NH3are dissolved and the solution is made upto 1000 ml
using distilled water.
15. Water Treatment & Analysis 15
Procedure
1) Standardisation of EDTA solution
20ml of Std.hard water is taken in a conical flask. 5 ml of buffer solution and a few drop of
EBT indicator are added. The solution is titrated against EDTA taken in burette. The endpoint is
the colour change from wine red to steel blue colour. Let the volume of EDTA consumed be V1ml.
Calculation
1ml of std.hard water = 1mg of CaCO3
20 ml of std. hard water = 20 mgs of CaCO3
20 ml of std. hard water consumes = V1ml of EDTA V1ml of EDTA consumes= 20 ml of
Std hardwater.
= 20 x 1 mg of CaCO3eq. hardness
1 ml of EDTA = 20/ v1 mg / L CaCO3 eq. hardness
2) Estimation of Total Hardness
20ml of sample hard water is pipetted out into a conical flask and titrated against EDTA
taken in burette by adding the buffer and the indicator to get the end point. Let the volume of
EDTA consumed be V2ml.
Calculation
20 ml of sample hardwater = V2ml of EDTA
= V2 X 20/V1 mg of CaCO3 eq. Hardness
In 1000 ml of water sample = V2 X 20/ V1 X 1000/20 mg of CaCO3 eq.hardness
Total hardness= 1000 x V2/ V1 mg / L (or) ppm.
3) Estimation of Permanent Hardness
250ml of water sample is boiled off to a volume of 50 ml in a beaker to remove temporary
hardness. The temporary hard salts settle down. Filter and wash thoroughly and make up the
solution again to 250 ml. 20 ml of this solution which isfree from carbonate hardness is titrated
against the EDTA as done before. Let the volume of EDTA consumed be V3ml.
Calculation
20 ml of boiled sample hard water consumes = V3ml of EDTA
= V3 X 20/ V1 mg of CaCO3 eq. hardness
In 1000 ml of water sample
= V3 X 20 / V1 X 1000/ 20 mg of CaCO3 eq. hardness
16. Water Treatment & Analysis 16
= 1000 x V3/ V1 mg/ L (or) ppm.
Permanent hardness= 1000 x V3/ V1 mg/L (or) ppm.
Estimation of Temporary Hardness
This can be calculated by using the following methods.
Temporary Hardness = Total Hardness – Permanent Hardness
Temporary Hardness = 1000 × x V2 – V3 / V1 mg/L (or) ppm.
Advantages of EDTA method
This method is more accurate in the estimation of hardness of water than other methods rapid
process.
It is convenient and more rapid process.
Problem
1. While titrating a sample of hard water, 50 ml of the sample consumed 10 ml of 0.01 M
EDTA to attain the end point. Calculate the total hardness of the sample in terms of mg
equivalent of CaCO3per liter.
Solution:
Number of gram moles of EDTA consumed by 50 ml of sample
= M x V / 1000 = 0.01 x 10 / 1000 = 1 x 10 4
1 gm mole of EDTA = 100g of CaCO3
= 1 x 105
mg of CaCO3
Total hardness in 50 ml sample= 1 x104
x 1 x 105
= 10 mg of CaCO3
Hence total hardness of the given sample
= 10 / 50 x 1000 = 200 mg /L of CaCO3
2. 100 ml of water sample require 20 ml N/ 100 EDTA when titrated using NH4Cl _NH4OH
buffer and EBT indicator. Calculate the hardness of the sample.
Solution:
No. of gm eq. of EDTA used by 100 ml sample = N xV / 1000 = (1/100) x 20 / 1000 =
2.0 x 10 4
no of gm moles of EDTA consumed
= 2.0 x 10 4
/2 = 1.0 x 10 4
17. Water Treatment & Analysis 17
1 gm of mole of EDTA = 105
mg of CaCO3
1x 10 4
gm of mole of EDTA= 105
1.0 x 104
= 10 mg of CaCO3
Hence total hardness of the sample= 10 / 100 x 1000
= 100 mg /L of CaCO3
3. 100 ml of a hard water sample require 25 ml of 0.01 M EDTA with NH4Cl-NH4OH buffer
and EBT indicator. Another 100ml of the sample is boiled for about half an hour and after
filtering the precipitate, the volume of the filtrate is made to 100 ml again by the addition of
distilled water. 20ml of this boiled sample require only 4 ml of 0.01 M EDTA following the
same procedure. Calculate the temporary and permanent hardness of the sample.
Solution:
i) Calculation of total hardness of the sample:
100 ml of the sample requires 25 ml of 0.01 M EDTA.
No. of gram moles of EDTA consumed = 0.01x 25 / 1000 = 2.5 x 10 4
1 gm moles of EDTA = 105
mg of CaCO3
2.5 x104
gm moles of EDTA = 105
x 2.5 x104
= 25 mg of CaCO3
Hence total hardness of the given sample
= 25/ 100 x 1000 = 250 mg /L of CaCO3
ii)Calculation of permanent hardness
the boiled sample will contain only permanent hardness 20 ml of boiled sample consumes
4 ml of 0.01 M EDTA. No. of gm moles of EDTA consumed.
= 0.01x 4 / 1000 = 4 x10 5
1 gm mole of EDTA = 105
mg of CaCO3
4x 10 5
gm moles of EDTA = 105
x 4x105
= 4 mg of CaCO3
Hence permanent hardness of the given sample
= 4 / 20 x 1000 = 200 mg /L of CaCO3
18. Water Treatment & Analysis 18
iii)Calculation of temporary hardness
temporary hardness = Total hardness – Permanent hardness
= (250 – 200) mg / L of CaCO3
= 50 mg / L of CaCO3.CaCO
Reference
1. Engineering Chemistry II, Dr. Syed Shabudeen. P. S. Professor chemistry and Environmental
science, pp. 1.1 to 1.95, October 2010, Kumaraguru College of Technology.
2. Water Treatment & Analysis, Kanwaljit Kaur.
3. https://www.scribd.com/document/23180395/Engineering-Chemistry-Unit-I-Water-
Treatment
Question
Section - A
1. What is meant by softening of water?
2. What is clarks process?
3. What are zeolites mention its general formulas?
4. What are advantages of ion-exchange process?
5. Draw EDTA structure.
Section – B
1. What is lime soda process? Explain the functions of lime and soda.
2. Explain the zeolite process of water softening with neat diagram.
3. How will you determine the temporary & permanent by titration method?
4. Explain the modified lime soda process of softening of water.
Section - C
1. Explain the detail the cold & hot lime soda process with neat diagram.
2. Explain the ion-exchange process in detail with neat diagram.
3. Explain the various steps involved in EDTA method?
4. 100 ml of hard water requires 20 ml of EDTA solution for titration. 22 ml of the same EDTA
solution was required for the titration of 100 ml of standard hardwater containing 1gm
CaCO3per litre. Determine the hardness of water sample in ppm.
5. 250 ml of hard water required 17 ml of 0.025 M EDTA solution to attain the end point.
Calculate the hardness of water.
19. Water Treatment & Analysis 19
6. 100 ml of water sample requires 18ml of EDTA solution for titration. 1 ml of EDTA
solution is equivalent to 1.1 mgs of CaCO3. Determine the hardness in ppm.
7. 100ml of a sample of water required 18 ml of 0.01M EDTA for titration using
Erio-chrome Black-T indicator. In another experiment, 100ml of the same sample
was boiled to remove the CH, the precipitate was removed and the cold solution
required 10 mlof 0.01 M EDTA using Erio-chrome Black- T indicator. Calculate i)
the total hardness, ii) permanent hardness or NCH iii) carbonatehardnessCH,in
terms of mg/lit ofCaCO3.
8. 500 ml of a water sample is boiled for 1hr. It is then cooled and filtered. The filtrate
is made upto 500ml again with distilled water.50ml of this solution requires 12 ml
of N/50 EDTA with EBT-indicator and NH4Cl-NH4OH buffer. Determine the
permanent hardness of the water sample