Test Rig For IRAB Brake System
•Download as PPTX, PDF•
0 likes•393 views
The system is designed to test the performance/Functional testing of the following 18 types of pneumatic valves of IRAB Brake system for for electric locomotives. The system is consisting Brake Pipe, Auxiliary Reservoir, Brake Cylinder Reservoir and Control Reservoir. The test stand have a structure composed of SS –Section with pressure gauges construction housing with digital pressure gauges at front of the stand. The right and left side and the rear side of the test stand is provided with detachable covers and doors. All the air reservoirs and pneumatic piping are accommodated inside of the test stand. The test stand operation is controlled by the computer system by means of predefined software.
Report
Share
Report
Share
Recommended
computerized-control-universal-brake-test-bench.pptx
The system is designed to test the performance/Functional testing of the following 27 types of pneumatic valves of AC Brake system of AC Rake for Metro Rail. The system is consisting Brake Pipe, Auxiliary Reservoir, Brake Cylinder Reservoir and Control Reservoir. The system has Dew point sensor, Noise level transmitter. The test stand have a structure composed of Aluminum –Section with pressure gauges construction housing with digital pressure gauges at front of the stand. The right and left side and the rear side of the test stand is provided with detachable covers and doors. All the air reservoirs and pneumatic piping are accommodated inside of the test stand.
computerized-microprocessor-controlled-dv-test-bench.pptx
The system is designed to test the performance of the Distributor valve. Distributor Valve works on Pressure difference in the Brake Pipe. The system is consisting Brake Pipe, Auxiliary Reservoir, Brake Cylinder and Control Reservoir. The system consist Data Acquisition systems including IPC, Printer and UPS for power back up.
The DV Test Rig Test the following Parameters one by one:
Charging Time of AR & CR
Brake Application Time
In Full Service Application
In Emergency Application
Brake Releasing Time
In Full Service Application
In Emergency Application
Max. Brake Cylinder Pressure
In Full Service Application
In Emergency Application
Leakage Test
Sensitivity
Graduated Application
Graduated Release
Graduated Release
Re-feeding Test
Availability of BP pressure
Overcharge Protection Test
Quick Release Valve Test
Combined control unit ppt
The test rig is a fully computerized and automated system used to test servo hydraulic actuators from aviation components like helicopters and fighter planes. It can control up to 120 testing sequences and generate customized reports. The rig can test any servo hydraulic actuator through various tests like frequency response analysis, load and displacement simulations, and measuring cyclic tests. It is operated either automatically through pre-programmed software or manually without software control.
H60
The Idle Air Control system uses an idle air control valve controlled by the ECM to regulate air flow and stabilize idle speed. There are four types of IAC systems that vary in their design and operation but all control idle speed. Improper operation of the IAC system can impact emissions and driveability by causing rough or unstable idle conditions.
Test Rig for 130LPM Pump of LCA- Neometrix
The Test Rig is self-contained, Electro Hydraulic Test Rig. Safety & user Friendliness are the key features of the provided Test Rig. The Test Rig provided has been designed to address all the requirements testing of 130 LPM Pump. The brief spec and tests of this pump is given below as:
The brief specs of the pump-
Rated Pressure = 270 bars
Rated Flow = 130 LPM at 270 bar
Rated Speed = 6000 RPM
Application
The Test Rig provided has been designed to address all the requirements testing of 130 LPM Pump.
Key features
Drive System with Gear Box Lube Oil System
High Pressure System for Pressure Proof Testing
Low Pressure System for Functional Test
Control and Indicator Panel
Data Acquisition System.
The test rig is design to work up to 120°C.
Two moog make servo valves have been provided in Rig for Cyclic Test.
Cooling System: We are using water as the medium for the cooling purpose, with the help of Heat Exchanger. Total three heat exchanger has been provided in system.
Filtration: Proper filtration has been provided and the filters have electronic clogging indicators.
The rig is developed for Hydraulic Oil (MIL-H- 5606E) or equivalent.
Three SS 304 Reservoirs of oil capacity 90, 225 and 50 liters have been provided with all related fittings.
Safety Interlocks
The Pump will not start in case the Reservoir oil level is low/ high.
The Pump will stop/ will not start, in case the oil temperature goes beyond a set limit.
There would be alarm and indication, in case any abnormality happens.
In case any of the filters are clogged, there would be alarm; Indication and the Test rig will stop.
It is also independent of the Computer automation system.
Computer: The Rig Diagnostics/ Monitoring & Recording are implemented Through the National Instruments data acquisition System and PC. The customized Software is implemented in Lab View.
Dv test rig
The system is designed to test the performance of distributor valves used in coach and wagon braking systems. It consists of a brake pipe, auxiliary reservoir, brake cylinder and control reservoir. The system can automatically run through a predefined test sequence or allow manual testing of individual components. It uses compressed air at pressures up to 10 kg/cm2 and has safety features to prevent contact with sensors or circuitry during operation. Proper procedure and safety precautions must be followed when using the system.
Hydraulic flushing rig ppt
This document describes the specifications of a hydraulic flushing rig. It can be used to clean systems contaminated with large amounts of debris. The rig contains:
- A 300 liter stainless steel tank for hydraulic oil
- Pumps capable of 58 LPM at 350 kg/cm2 pressure
- Filters down to 2 microns to clean the oil
- A heat exchanger to control oil temperature below 60°C
- All piping and fittings are stainless steel for use with water or oil-based fluids
- Gauges and controls mounted on a stainless steel panel
- It can clean systems to a NAS 6 cleanliness standard and is certified.
Automotive catalogue
opus automazione S.p.A manufactures standard and customized test benches, which satisfy the test specifications requirements of the most important carmakers.
opus has been producing for twenty years test benches for a wide range of products and other kind of test benches for example exhaust gases analysis both diesel and petrol engines.
A standard test benches overview is shown in this catalogue.
Recommended
computerized-control-universal-brake-test-bench.pptx
The system is designed to test the performance/Functional testing of the following 27 types of pneumatic valves of AC Brake system of AC Rake for Metro Rail. The system is consisting Brake Pipe, Auxiliary Reservoir, Brake Cylinder Reservoir and Control Reservoir. The system has Dew point sensor, Noise level transmitter. The test stand have a structure composed of Aluminum –Section with pressure gauges construction housing with digital pressure gauges at front of the stand. The right and left side and the rear side of the test stand is provided with detachable covers and doors. All the air reservoirs and pneumatic piping are accommodated inside of the test stand.
computerized-microprocessor-controlled-dv-test-bench.pptx
The system is designed to test the performance of the Distributor valve. Distributor Valve works on Pressure difference in the Brake Pipe. The system is consisting Brake Pipe, Auxiliary Reservoir, Brake Cylinder and Control Reservoir. The system consist Data Acquisition systems including IPC, Printer and UPS for power back up.
The DV Test Rig Test the following Parameters one by one:
Charging Time of AR & CR
Brake Application Time
In Full Service Application
In Emergency Application
Brake Releasing Time
In Full Service Application
In Emergency Application
Max. Brake Cylinder Pressure
In Full Service Application
In Emergency Application
Leakage Test
Sensitivity
Graduated Application
Graduated Release
Graduated Release
Re-feeding Test
Availability of BP pressure
Overcharge Protection Test
Quick Release Valve Test
Combined control unit ppt
The test rig is a fully computerized and automated system used to test servo hydraulic actuators from aviation components like helicopters and fighter planes. It can control up to 120 testing sequences and generate customized reports. The rig can test any servo hydraulic actuator through various tests like frequency response analysis, load and displacement simulations, and measuring cyclic tests. It is operated either automatically through pre-programmed software or manually without software control.
H60
The Idle Air Control system uses an idle air control valve controlled by the ECM to regulate air flow and stabilize idle speed. There are four types of IAC systems that vary in their design and operation but all control idle speed. Improper operation of the IAC system can impact emissions and driveability by causing rough or unstable idle conditions.
Test Rig for 130LPM Pump of LCA- Neometrix
The Test Rig is self-contained, Electro Hydraulic Test Rig. Safety & user Friendliness are the key features of the provided Test Rig. The Test Rig provided has been designed to address all the requirements testing of 130 LPM Pump. The brief spec and tests of this pump is given below as:
The brief specs of the pump-
Rated Pressure = 270 bars
Rated Flow = 130 LPM at 270 bar
Rated Speed = 6000 RPM
Application
The Test Rig provided has been designed to address all the requirements testing of 130 LPM Pump.
Key features
Drive System with Gear Box Lube Oil System
High Pressure System for Pressure Proof Testing
Low Pressure System for Functional Test
Control and Indicator Panel
Data Acquisition System.
The test rig is design to work up to 120°C.
Two moog make servo valves have been provided in Rig for Cyclic Test.
Cooling System: We are using water as the medium for the cooling purpose, with the help of Heat Exchanger. Total three heat exchanger has been provided in system.
Filtration: Proper filtration has been provided and the filters have electronic clogging indicators.
The rig is developed for Hydraulic Oil (MIL-H- 5606E) or equivalent.
Three SS 304 Reservoirs of oil capacity 90, 225 and 50 liters have been provided with all related fittings.
Safety Interlocks
The Pump will not start in case the Reservoir oil level is low/ high.
The Pump will stop/ will not start, in case the oil temperature goes beyond a set limit.
There would be alarm and indication, in case any abnormality happens.
In case any of the filters are clogged, there would be alarm; Indication and the Test rig will stop.
It is also independent of the Computer automation system.
Computer: The Rig Diagnostics/ Monitoring & Recording are implemented Through the National Instruments data acquisition System and PC. The customized Software is implemented in Lab View.
Dv test rig
The system is designed to test the performance of distributor valves used in coach and wagon braking systems. It consists of a brake pipe, auxiliary reservoir, brake cylinder and control reservoir. The system can automatically run through a predefined test sequence or allow manual testing of individual components. It uses compressed air at pressures up to 10 kg/cm2 and has safety features to prevent contact with sensors or circuitry during operation. Proper procedure and safety precautions must be followed when using the system.
Hydraulic flushing rig ppt
This document describes the specifications of a hydraulic flushing rig. It can be used to clean systems contaminated with large amounts of debris. The rig contains:
- A 300 liter stainless steel tank for hydraulic oil
- Pumps capable of 58 LPM at 350 kg/cm2 pressure
- Filters down to 2 microns to clean the oil
- A heat exchanger to control oil temperature below 60°C
- All piping and fittings are stainless steel for use with water or oil-based fluids
- Gauges and controls mounted on a stainless steel panel
- It can clean systems to a NAS 6 cleanliness standard and is certified.
Automotive catalogue
opus automazione S.p.A manufactures standard and customized test benches, which satisfy the test specifications requirements of the most important carmakers.
opus has been producing for twenty years test benches for a wide range of products and other kind of test benches for example exhaust gases analysis both diesel and petrol engines.
A standard test benches overview is shown in this catalogue.
Pneumatic system
The pneumatic system provides compressed air for aircraft functions like air conditioning, engine starting, and anti-ice systems. It obtains air from the engine bleed ports and controls the air pressure, temperature, and cleanliness. Leak detection loops monitor the hot air ducts and can isolate leaks by closing valves. The pneumatic system is controlled and monitored via panels and ECAM displays.
SISTEMA DE AIRE FRENOS 793D
The document discusses the air and brake systems of a 793D truck. It has separate parking/secondary and service/retarder brake systems. The parking brakes are spring engaged and hydraulically released, while the service brakes are engaged hydraulically via an air-over-oil system. An engine-driven air compressor supplies air to functions like braking and starting. The air flows through tanks, valves, and cylinders to engage the different brake systems.
Hydraulic Control Valve Test Bench.pptx
Neometrix make Hydraulic Control Valve Test Bench (Model: NEA1811) is designed specially to cover almost all high pressure,high flow and high temperature precise testing requirements of both Industrial and Mobile Hydraulic application Industries. This test stand has been proved to enable test labs to test hydraulic valves at pressure up to 420 bar and with maximum flow up to 400 lpm at temperature up to 85 °C.
Machine is capable of doing following tests with accuracy for both Mobile and Industrial Hydraulic valves-
Endurance Test
Hysteresis Test
Impulse Test
Flow Compensation Test
Flow Accuracy Test
Response Time Test
Pressure Drop Test
Leakage Test
Pull In & Drop Out Test
Hydraulic Hose Leak Testing (Test Rig is Pneumatic Hydraulic).pptx
The Test Rig is Pneumatic Hydraulic. Safety & user Friendliness are the key features of the provided Test Rig. The Test Rig has been designed to address all the requirements of the Design Document.
With this Test Rig, Operator can work independently.
The entire Test as specified can be done on this Test Rig.
Trial 2 overview of oil handling operations mc cord pipeline
The 14.25 mile long, 6-inch diameter jet fuel pipeline starts at a pump station near fuel tanks 30002 and 30003 and ends at an Air Force Base fuel depot. It is monitored for leaks during fuel transfer operations by comparing the fuel volume measured entering and exiting, and when static by watching for unexplained pressure drops exceeding 15 psi. Critical components include isolation valves, pressure relief valves, and a cathodic protection system running the length of the line to prevent corrosion.
Wash machine test equipment
We supply Various Performance, Fatigue Test Machine,
Automotive, Bike, Vehicle Parts Test Facilities
Bearing, Gear, Joint, Coupling, Transmission Test Bench
Dynamometer: for Electric Motor, Engine, Generator Brake Test
Hydraulic Testing Equipments: Pump, Valve, Pipe Test
Shaking Table, Seismic Simulator
Automatic Assembly Line
Engine Kaveri
Kaveri engine has 7 components, these components are Low Pressure and High Pressure Compressors, Annular Combustor, High Pressure and Low Pressure Turbines, Afterburner System, Engine Gearbox, Electro-Hydro Mechanical Control Systems, Kaveri Digital Engine Control Unit.
Kaveri engine- Kaveri Engine DRDO
Kaveri engine is an afterburning turbofan project developed by the GTRE, lab under DRDO, India. GTRE is now running two separate successor engine programmes, the K9+ and the K10. Click here to know more about kaveri Engine : http://www.drdo.gov.in/drdo/English/index.jsp?pg=Kaveri.jsp
ACM-test-bench-ppt.pptx
The ACM test bench controls test parameters like air flow, pressure, and temperature when operationally testing the EC70 air cycle machine. Various sensors measure temperatures, pressures, shaft displacement and more to ensure the air conditions match aircraft specifications. The test rig is designed for repeatable and accurate results and was approved by regulatory authorities.
Precocity Automation Catalog
Precocity Automation System provides customized test and measurement automation solutions and special purpose machines for applications across various industries. They have expertise in designing test benches for testing automotive HVAC components and systems. Precocity aims to offer innovative engineering solutions while leveraging their technical expertise and experience in industrial automation.
Technical description bvg 2014 (en) light
The document provides technical details about Adicomp's oil-injected rotary screw gas compressors and treatment systems for biogas, landfill gas, and other wet gases. Key points include:
- Capacity ranges from 3000Nm3/h up to pressures of 25bar(g) with motor power from 4-400kW.
- Adicomp has over 15 years of experience supplying hundreds of biogas, landfill gas, and other gas compression and treatment installations around the world.
- The compressors and treatment systems are compact, quiet, and suitable for various industrial sectors in temperature ranges from -20°C to 40°C.
- Adicomp considers itself a leader
EmJ to boost the CO2 compressor pack efficiency in warm climate
Cristian Corato's speech during Chillventa 2018 on how is now possible to use transcritical CO2 applications in warmer climates and commercial refrigeration thanks to our EmJ Electronic modulating Ejectors
Technical description vg 2014 (en) light
This document provides technical details about VG oil-injected rotary screw gas compressors and treatment systems for compressing dry methane or natural gas. Key details include:
- Capacities up to 3000Nm3/h and discharge pressures from 3.5 to 25 bar(g).
- Adicomp has over 15 years of experience supplying hundreds of biogas, landfill gas, natural gas, and other gas compression and treatment installations around the world.
- The compressors can operate in temperatures from -20°C to 40°C and extreme weatherproof versions are available for installation in harsh climates.
Volvo Wheel Loader L120d Service Manual
This document provides specifications for the Volvo L120D wheel loader, including:
1) It lists the engine output between 148-153 kW and operating weight between 18.4-20.6 tons.
2) The steering system uses a load-sensing hydrostatic articulated design with a double variable-flow axial piston pump and two double-acting cylinders.
3) The hydraulic system uses an open center design with efficient high capacity vane pumps allowing precision control at low engine RPM.
Computerized Based Test Bench For Panel Mounted Brake System For LHB Coches
Computerized Based Test Bench For Panel Mounted Brake System For LHB CochesNeometrix_Engineering_Pvt_Ltd
The System is designs to test the performance of the LHB Brake panel. LHB Brake panel works on Pressure difference in the Brake Pipe .The system is consisting Brake Pipe, Auxiliary Reservoir, Brake Cylinder and Control Reservoir.
The Microprocessor/computerized Based Test Bench for Panel Mounted Brake System for LHB Coaches For different designs Air Brake System running over Indian Railways i.e. KBI design, Faively design & Escorts design etc.
ONTAP - Airbrakes
This document provides an overview of air brake systems that are commonly used on tractor-trailers and other large commercial vehicles. It describes the main components of air brake systems, including the foundation brakes, air supply subsystem, primary and secondary circuits, and spring brake subsystem. The air supply subsystem uses an air compressor, governor, air tanks, and optional air dryer to store and regulate compressed air. The foundation brakes use either drum brakes or disc brakes to stop the wheels. Air is routed through the primary and secondary circuits to apply the service brakes. The spring brake subsystem provides emergency braking ability.
ONTAP - Air Brakes
This document provides an overview of air brake systems used on commercial vehicles. It discusses how air brake systems use compressed air stored in tanks to produce braking force. The key components of air brake systems are then outlined, including the foundation brake components of drum and disc brakes, the air supply subsystem of compressors, governors, tanks and dryers, and the primary and secondary subsystems which use a dual circuit design for redundancy. The document provides details on how these various components work and interact to stop the vehicle when the driver presses the brake pedal.
18 OBDG04 ECM Summary Tables
The document describes the monitor strategy for several fault codes related to the heater coolant pump control circuit and the crankshaft position-camshaft position correlation. It provides the fault code, monitor strategy description, malfunction criteria, threshold values, secondary parameters, enable conditions, time required, and MIL illumination for each.
Compressor deltav
Emerson's SmartProcess Compressor provides an integrated control solution for centrifugal and axial compressors that maximizes performance and efficiency. The solution includes modules for antisurge control, load control, load sharing control, and automated startup/shutdown sequencing. It utilizes DeltaV control functions and smart field devices to minimize response time and stabilize the main process parameter while preventing surge and minimizing energy consumption. The software is pre-engineered for easy implementation and support by plant personnel.
Shell tube design
This research paper models and controls the temperature of a shell and tube heat exchanger using two PID controller tuning methods. An ARMAX model is obtained from experimental PRBS data to mathematically model the heat exchanger dynamics. PID settings are designed using Internal Model Control (IMC) tuning and relay auto-tuning methods. Experimental results show that the IMC-tuned PID controller provides better control of the cold fluid outlet temperature in terms of error metrics than the relay auto-tuned controller.
Standard Reomte Control Interface - Neometrix
About
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.
Technical Specifications
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
Key Features
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface
• Compatible with MAFI CCR system
• Copatiable with IDM8000 CCR
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
Application
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.
Integrated Test Rig For HTFE-25 - Neometrix
The purpose of Integrated Test Rig is to assess performance of Fuel Cooled Oil Cooler (FCOC), HP Pump & Oil Pump prior to fitment on Aero Engine. The design of rig is such that it can cater to individual testing of individual LRU or integrated testing of all the LRU’s installed together (in combination). The pumps under test shall be mounted directly on the high-speed electric motor flange through adapter quill shaft assembly. Variable speed drives shall be provided for all the pumps under testing. The rig shall cater for real time monitoring and recording of performance parameters.
KEY FEATURES
Key features of this Rig are as follows: -
1. It has separate power packs for both the fluids i.e. ATF Power pack for ATF Fluid, OX Power Pack for OX-27 Oil.
2. This Rig is designed for high temperature Application. It works on 200 deg. Celsius.
3. Two Dedicated heating systems have been integrated with this Rig to raise the temperature of OX-27 Oil.
4. In both Power Packs insulated tanks are being used, which is good for safe operation and safety of operator.
5. This rig is designed in such a way, that it’s OX power pack is in its left side, ATF Power pack is in right Side and test bed is in Centre.
6. A big Test bed have been provided for smooth testing of UUT’s.
7. All piping is being insulated for safe operation and maintenance.
8. It comprises with DAQ System.
9. This rig can test several components at a time, together or separately.
Application
All the UUT’s are mounted on HTFE-25 Engine after successful performance testing of those. Application of this Rig are as follows: -
1. One of its application is to test LP Pump of HTFE-25. It is designed for functional testing of LP Pump.
a. Free Flow Test
b. Load Test
2. It is used to test HP Pump of HTFE-25. It is designed for functional testing of HP Pump.
a. Free Flow Test
b. Load Test
3. It is used to test Oil Pump of HTFE-25. It is designed for functional testing of Oil Pump.
4. It is used to test FCOC of HTFE-25.
More Related Content
Similar to Test Rig For IRAB Brake System
Pneumatic system
The pneumatic system provides compressed air for aircraft functions like air conditioning, engine starting, and anti-ice systems. It obtains air from the engine bleed ports and controls the air pressure, temperature, and cleanliness. Leak detection loops monitor the hot air ducts and can isolate leaks by closing valves. The pneumatic system is controlled and monitored via panels and ECAM displays.
SISTEMA DE AIRE FRENOS 793D
The document discusses the air and brake systems of a 793D truck. It has separate parking/secondary and service/retarder brake systems. The parking brakes are spring engaged and hydraulically released, while the service brakes are engaged hydraulically via an air-over-oil system. An engine-driven air compressor supplies air to functions like braking and starting. The air flows through tanks, valves, and cylinders to engage the different brake systems.
Hydraulic Control Valve Test Bench.pptx
Neometrix make Hydraulic Control Valve Test Bench (Model: NEA1811) is designed specially to cover almost all high pressure,high flow and high temperature precise testing requirements of both Industrial and Mobile Hydraulic application Industries. This test stand has been proved to enable test labs to test hydraulic valves at pressure up to 420 bar and with maximum flow up to 400 lpm at temperature up to 85 °C.
Machine is capable of doing following tests with accuracy for both Mobile and Industrial Hydraulic valves-
Endurance Test
Hysteresis Test
Impulse Test
Flow Compensation Test
Flow Accuracy Test
Response Time Test
Pressure Drop Test
Leakage Test
Pull In & Drop Out Test
Hydraulic Hose Leak Testing (Test Rig is Pneumatic Hydraulic).pptx
The Test Rig is Pneumatic Hydraulic. Safety & user Friendliness are the key features of the provided Test Rig. The Test Rig has been designed to address all the requirements of the Design Document.
With this Test Rig, Operator can work independently.
The entire Test as specified can be done on this Test Rig.
Trial 2 overview of oil handling operations mc cord pipeline
The 14.25 mile long, 6-inch diameter jet fuel pipeline starts at a pump station near fuel tanks 30002 and 30003 and ends at an Air Force Base fuel depot. It is monitored for leaks during fuel transfer operations by comparing the fuel volume measured entering and exiting, and when static by watching for unexplained pressure drops exceeding 15 psi. Critical components include isolation valves, pressure relief valves, and a cathodic protection system running the length of the line to prevent corrosion.
Wash machine test equipment
We supply Various Performance, Fatigue Test Machine,
Automotive, Bike, Vehicle Parts Test Facilities
Bearing, Gear, Joint, Coupling, Transmission Test Bench
Dynamometer: for Electric Motor, Engine, Generator Brake Test
Hydraulic Testing Equipments: Pump, Valve, Pipe Test
Shaking Table, Seismic Simulator
Automatic Assembly Line
Engine Kaveri
Kaveri engine has 7 components, these components are Low Pressure and High Pressure Compressors, Annular Combustor, High Pressure and Low Pressure Turbines, Afterburner System, Engine Gearbox, Electro-Hydro Mechanical Control Systems, Kaveri Digital Engine Control Unit.
Kaveri engine- Kaveri Engine DRDO
Kaveri engine is an afterburning turbofan project developed by the GTRE, lab under DRDO, India. GTRE is now running two separate successor engine programmes, the K9+ and the K10. Click here to know more about kaveri Engine : http://www.drdo.gov.in/drdo/English/index.jsp?pg=Kaveri.jsp
ACM-test-bench-ppt.pptx
The ACM test bench controls test parameters like air flow, pressure, and temperature when operationally testing the EC70 air cycle machine. Various sensors measure temperatures, pressures, shaft displacement and more to ensure the air conditions match aircraft specifications. The test rig is designed for repeatable and accurate results and was approved by regulatory authorities.
Precocity Automation Catalog
Precocity Automation System provides customized test and measurement automation solutions and special purpose machines for applications across various industries. They have expertise in designing test benches for testing automotive HVAC components and systems. Precocity aims to offer innovative engineering solutions while leveraging their technical expertise and experience in industrial automation.
Technical description bvg 2014 (en) light
The document provides technical details about Adicomp's oil-injected rotary screw gas compressors and treatment systems for biogas, landfill gas, and other wet gases. Key points include:
- Capacity ranges from 3000Nm3/h up to pressures of 25bar(g) with motor power from 4-400kW.
- Adicomp has over 15 years of experience supplying hundreds of biogas, landfill gas, and other gas compression and treatment installations around the world.
- The compressors and treatment systems are compact, quiet, and suitable for various industrial sectors in temperature ranges from -20°C to 40°C.
- Adicomp considers itself a leader
EmJ to boost the CO2 compressor pack efficiency in warm climate
Cristian Corato's speech during Chillventa 2018 on how is now possible to use transcritical CO2 applications in warmer climates and commercial refrigeration thanks to our EmJ Electronic modulating Ejectors
Technical description vg 2014 (en) light
This document provides technical details about VG oil-injected rotary screw gas compressors and treatment systems for compressing dry methane or natural gas. Key details include:
- Capacities up to 3000Nm3/h and discharge pressures from 3.5 to 25 bar(g).
- Adicomp has over 15 years of experience supplying hundreds of biogas, landfill gas, natural gas, and other gas compression and treatment installations around the world.
- The compressors can operate in temperatures from -20°C to 40°C and extreme weatherproof versions are available for installation in harsh climates.
Volvo Wheel Loader L120d Service Manual
This document provides specifications for the Volvo L120D wheel loader, including:
1) It lists the engine output between 148-153 kW and operating weight between 18.4-20.6 tons.
2) The steering system uses a load-sensing hydrostatic articulated design with a double variable-flow axial piston pump and two double-acting cylinders.
3) The hydraulic system uses an open center design with efficient high capacity vane pumps allowing precision control at low engine RPM.
Computerized Based Test Bench For Panel Mounted Brake System For LHB Coches
Computerized Based Test Bench For Panel Mounted Brake System For LHB CochesNeometrix_Engineering_Pvt_Ltd
The System is designs to test the performance of the LHB Brake panel. LHB Brake panel works on Pressure difference in the Brake Pipe .The system is consisting Brake Pipe, Auxiliary Reservoir, Brake Cylinder and Control Reservoir.
The Microprocessor/computerized Based Test Bench for Panel Mounted Brake System for LHB Coaches For different designs Air Brake System running over Indian Railways i.e. KBI design, Faively design & Escorts design etc.
ONTAP - Airbrakes
This document provides an overview of air brake systems that are commonly used on tractor-trailers and other large commercial vehicles. It describes the main components of air brake systems, including the foundation brakes, air supply subsystem, primary and secondary circuits, and spring brake subsystem. The air supply subsystem uses an air compressor, governor, air tanks, and optional air dryer to store and regulate compressed air. The foundation brakes use either drum brakes or disc brakes to stop the wheels. Air is routed through the primary and secondary circuits to apply the service brakes. The spring brake subsystem provides emergency braking ability.
ONTAP - Air Brakes
This document provides an overview of air brake systems used on commercial vehicles. It discusses how air brake systems use compressed air stored in tanks to produce braking force. The key components of air brake systems are then outlined, including the foundation brake components of drum and disc brakes, the air supply subsystem of compressors, governors, tanks and dryers, and the primary and secondary subsystems which use a dual circuit design for redundancy. The document provides details on how these various components work and interact to stop the vehicle when the driver presses the brake pedal.
18 OBDG04 ECM Summary Tables
The document describes the monitor strategy for several fault codes related to the heater coolant pump control circuit and the crankshaft position-camshaft position correlation. It provides the fault code, monitor strategy description, malfunction criteria, threshold values, secondary parameters, enable conditions, time required, and MIL illumination for each.
Compressor deltav
Emerson's SmartProcess Compressor provides an integrated control solution for centrifugal and axial compressors that maximizes performance and efficiency. The solution includes modules for antisurge control, load control, load sharing control, and automated startup/shutdown sequencing. It utilizes DeltaV control functions and smart field devices to minimize response time and stabilize the main process parameter while preventing surge and minimizing energy consumption. The software is pre-engineered for easy implementation and support by plant personnel.
Shell tube design
This research paper models and controls the temperature of a shell and tube heat exchanger using two PID controller tuning methods. An ARMAX model is obtained from experimental PRBS data to mathematically model the heat exchanger dynamics. PID settings are designed using Internal Model Control (IMC) tuning and relay auto-tuning methods. Experimental results show that the IMC-tuned PID controller provides better control of the cold fluid outlet temperature in terms of error metrics than the relay auto-tuned controller.
Similar to Test Rig For IRAB Brake System (20)
Hydraulic Hose Leak Testing (Test Rig is Pneumatic Hydraulic).pptx
Hydraulic Hose Leak Testing (Test Rig is Pneumatic Hydraulic).pptx
Trial 2 overview of oil handling operations mc cord pipeline
Trial 2 overview of oil handling operations mc cord pipeline
EmJ to boost the CO2 compressor pack efficiency in warm climate
EmJ to boost the CO2 compressor pack efficiency in warm climate
Computerized Based Test Bench For Panel Mounted Brake System For LHB Coches
Computerized Based Test Bench For Panel Mounted Brake System For LHB Coches
More from Neometrix_Engineering_Pvt_Ltd
Standard Reomte Control Interface - Neometrix
About
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.
Technical Specifications
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
Key Features
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface
• Compatible with MAFI CCR system
• Copatiable with IDM8000 CCR
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
Application
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.
Integrated Test Rig For HTFE-25 - Neometrix
The purpose of Integrated Test Rig is to assess performance of Fuel Cooled Oil Cooler (FCOC), HP Pump & Oil Pump prior to fitment on Aero Engine. The design of rig is such that it can cater to individual testing of individual LRU or integrated testing of all the LRU’s installed together (in combination). The pumps under test shall be mounted directly on the high-speed electric motor flange through adapter quill shaft assembly. Variable speed drives shall be provided for all the pumps under testing. The rig shall cater for real time monitoring and recording of performance parameters.
KEY FEATURES
Key features of this Rig are as follows: -
1. It has separate power packs for both the fluids i.e. ATF Power pack for ATF Fluid, OX Power Pack for OX-27 Oil.
2. This Rig is designed for high temperature Application. It works on 200 deg. Celsius.
3. Two Dedicated heating systems have been integrated with this Rig to raise the temperature of OX-27 Oil.
4. In both Power Packs insulated tanks are being used, which is good for safe operation and safety of operator.
5. This rig is designed in such a way, that it’s OX power pack is in its left side, ATF Power pack is in right Side and test bed is in Centre.
6. A big Test bed have been provided for smooth testing of UUT’s.
7. All piping is being insulated for safe operation and maintenance.
8. It comprises with DAQ System.
9. This rig can test several components at a time, together or separately.
Application
All the UUT’s are mounted on HTFE-25 Engine after successful performance testing of those. Application of this Rig are as follows: -
1. One of its application is to test LP Pump of HTFE-25. It is designed for functional testing of LP Pump.
a. Free Flow Test
b. Load Test
2. It is used to test HP Pump of HTFE-25. It is designed for functional testing of HP Pump.
a. Free Flow Test
b. Load Test
3. It is used to test Oil Pump of HTFE-25. It is designed for functional testing of Oil Pump.
4. It is used to test FCOC of HTFE-25.
Neometrix Optical Balloon Theodolite.pptx
Neometrix Optical Balloon Theodolite
• In common with other land based balloon theodolites the Neometrix theodolite OT-NEA3060 has a telescope with a bent optical axis. A secondary wide-angle telescope using the same eyepiece is selectable with a mirror. There are two pins on the tip of this instrument that serve as contacts to an attachable battery case. The Photo shows the theodolite with the battery case attached.
• In the photo above you can see the bubble level directly under the two switches. The switches control illumination of the reticule and the circles.
• You can see the accessories for this instrument, filters for the eye piece, the key to the case, lens shade, lens cap and a plumb bob. Also note the hook for hanging a stopwatch and the magnifying glass to assist reading the circles.
• Distinguishing features of the OT-NE-A3060 theodolite are the use of a Pentagonal Prism in the bent axis telescope, which allows for better stability of the optical alignment, a closed circle design for durability, two levels of magnification offering wide and narrow fields of view (accomplished with a switchable finder scope using the same eyepiece with two objectives) and a lined gradicule supporting the tail method of altitude determination. The placement of the azimuth and elevation circles directly above each other as well as the use of Micrometer drums facilitates rapid determination of Azimuth and elevation directly to the 10th of a degree.
Dynamometer Engine Test Rig for engines parameters RPM
An Eddy current dynamometer is an electromechanical energy conversion device, which converts mechanical energy to electrical energy. It fundamentally uses Faraday’s Law of electromagnetic induction as its working principle.
In this system we test different ranges of engines RPM, Torque in N-m, and Power. And parameters will be shown in panel.
Power- up to 200 KW
Torque- 1780 N-m
Engine for testing with a range of 1500- 2000 rated rpm.
Engine monitoring system: Control panel with digital meters, oil pressure, lube oil temperature, water temperature, Engine RPM.
Engine parameter recording: A computer based data logger to record engine control parameters. A printer to be provided for printout report of all engines parameter.
And parallel we can record engines parameter like Lube oil pressure, Engine temperature, water temperature etc.
Mechanical Dimensions:-
• Overall Size: 2000 mm x 850mm x 1350 mm
• Centre Height: 900 mm
• Inlet Piping: 2”
• Outlet Piping: 2”
• Calibration Arm Length from centre: 1000 mm
• Cooling Water Requirement (Dynamometer Inlet) Pressure: 1.0-2.0 bars
• Temperature: Less than 40°C.
• Cooling Water Flow (Dynamometer Inlet): 12500 LPH
• Type of Lubrication: Grease (Inner earing), Oil (Outer Bearing)
Electrical:
• Supply Voltage:240 volts ± 10% AC, 50 Hz
• Separate Earth should be given to the system.
• Maximum Excitation: Internally set in the instrument depending on the capacity of Eddy current dynamometer. Generally, 3 To 5 Amps D.C.
• RPM: This is displayed by a 4 digit display. This displays Motor/dynamometer rpm.
• Accuracy: ± 1 rpm.
Environmental:
i) Temperature: 5 to 550C maximum
ii) Humidity: R.H. 95% maximum
Application:
Dynamometer system will test the engines parameters RPM, Torque, Power, Lube oil pressure, temperature, water temperature and result will be shown in control panel with digital meters.
Portable Digital Barometer for Indian Air force
Portable Barometer uses a silicon resonant pressure sensor DPS 8100 producing a pressure reading in pressure measurement units and pressure altitude. It also has a Comptek 10.1" tablet, mounted on an Aluminum enclosure. It can be used as a hand-held indicator tablet or instrument. The instrument can also communicate through a USB connector to extract out logged data. This USB port should be strictly used for App-related data transfer only. The instrument has an in-built tablet which should be used only for the TERPS App. The tablet is provided with a compatible charging adapter. This should be used only to charge the instrument. The instrument should be used within the operating and maximum safe working pressure conditions. Refer to the specification section in this manual for the details.
Sensor Port:
Keep the sensor port clean all the time. Protect the sensor against moisture, water, dirt and dust particles.
Do not block the sensor with any object as it may result in inaccurate reading output.
For better and accurate readings, keep the sensor port away from continuous pressure changing areas (for example, should not be close to AC, Fans, table fans etc.).
During pressure measurement, the device should be placed on the table or held in the orientation.
In case of hand-held application, hold the instrument as shown in Figure 3. While holding the unit, ensure that the hand does not block the sensor port.
USB Port:
This USB Port is specifically for extracting the exported data from the TERPS App. Do not use this port for any other activity. Use this port only for App-related data transfer. When not in use, close the USB port using the rubber cap.
TEST RIG FOR HYDRAULIC FLUID (A3987) - NEOMETRIX DEFENCE
PROJECT: TEST RIG FOR HYDRAULIC FLUID (A3987)
The test rig is used to test the anti-wear properties and the aging
behaviour of hydraulic fluids under defined and reproducible
conditions. For this purpose, a vane pump Vickers 35VQ25A-11*20
for ASTM D6973-2014 and a Bent Axis type axial piston pump
A2F10 for JCMAS P 045 are used as test objects. The subsequent
investigation of the wear inserts and oil condition then allows
conclusions about the performance of the tested fluids, especially
their ability to avoid wear and resist oxidation. The modern and
ergonomically designed test rig meets all the specifications of the
European Machinery Directive 2006/42/EG to a high standard or
equivalent Indian Standard. The test rig is used to determine the
wear characteristics and oxidation/ aging of non-petroleum and
petroleum hydraulic fluids. For this purpose, a rotary vane pump
generates a test pressure under specific boundary conditions. The
result obtained is the total mass loss from the cam ring and the ten
vanes (ASTM D6973-2014) after the test. For indicating oxidation
stability or aging behaviour of hydraulic fluids this test bench, uses a
bent axis pump A2FO10 and a pressure relief valve DBDS 10
K1X/400V as load at high temperatures. The test takes place under
the influence of air and a copper catalyst. This procedure allows for
an accelerated aging rate using a real hydraulic component. The test
rig parameters meet the specifications according to ASTM D6973-
2014 and JCMAS P 045. Additionally, it is capable of carrying out the
evaluation of hydraulic fluid for frictional characteristics and energy
efficiency performance under indigenously developed and
industrially simulated test methods by varying load, speed,
temperature, pressure, flow rate etc.
Hydraulic Loading System - Neometrix Defence
Hydraulic Loading System Serves the following purpose during engine run::
Loads the Engine mounted Hydraulic Pump by Varying the Outlet restriction to achieve specific Flow Rates at specified Pressure Range.
Carry out Cyclic Load Testing of the Hydraulic Pump.
There are six different module which after assembly become complete system.
Modules are following:
Oil tank module
Air Regulation module
Inlet module
Outlet module
Drain module
Loading valve module
Heat exchanger module
Portable oil filling module
KEY FEATURES
Design Pressure : 340 kg/cm2
Working Pressure : 270-295 kh/cm2
Working Flow : 20-210 LPM
Hydraulic Oil : MIL=H-5606/FH-51
Viscosity : 15CST @ 40°C
Density : 0.8735 AT 15.6°C
Tank Capacity : 175 Liters
Tank Max. Pressure : 10 kg/cm2
Max. Temp. at Pump Outlet : 100°C
Max. Temp. at Pump Intel : 80°C
Lock Loading Test Rig (ERU119 & ERU120) .pptx
This rig is designed for testing Ejection Release Units (ERU119 & ERU120) which are tested for Hook Proving Loads. These units are tested for load deformation and the test results will automatically come out as OK/NG on the basis of pre-fed Deformation & Load settings in the system. A self-contained Test Bench is provided to test both types of units.
Mechanical System:
Independent Bench for ERU119 & ERU120 is provided.
Horizontal Loading Facility for the units is provided.
Custom made fixture for holding the units, and unit profile will be accommodated in the fixture so that the unit is not damaged during testing.
LVDT with magnetic contact is provided for displacement measurement.
Both systems have Load Cells with in-situ calibration facility. In- situ calibration will be done automatically.
starter-generator-test-bench-Catalog.pptx
The Following Test Bench is for Testing Parameters of Starter Generator of
Advanced Light Helicopter (ALH).
The Test bench has following four tests :-
1) Generator Mode Load and no Load Test.
2) Starter Mode Load Test.
3) Vibration Measurement Test.
4) Concentricity And Bar to Bar Difference Measurement Test.
Test Bench Description:
This test will have a Combination of AC Motor of 5000 RPM rigidly Coupled with the Dual Output Gear Box having Ratio of 1:3 to give maximum speed of 15000 RPM at output . The output is to accommodate the shaft of 6KW Starter Generator With Suitable Clamping On the Common Flange.
Resistive Load Bank with good Cooling Facility provides load to the Starter Generator in steps of 0,50,100,150 and 200 Amp with additional loads of 300A , 375A and 450 Amp .Load is selected from the control panel through selectable switches.
A.C. Drive ABB make is also provided for this Test with Control signals
From control panel.
45 KVA Ground Power Unit for Raphael .pptx
Ground Power Unit(GPU) is used to give the power to the aircraft which is in the ground during the maintenance and repair work the GPU is used to power up the system externally, This GPU is having Dual output one is 45Kva AC power that consist of L-L 200V and L-N 115V ,150A and 400HZ four wire system another one will be DC 28.5 V 800A two wire system and it will deliver the two output simultaneously up to maximum range of 45 KVA, the following components are used to design the GPU.
Overview: A diesel engine/electric motor coupled with highly reliable alternator provides a perfect output to your aircrafts. With a touchscreen control panel and interactive GUI, this GPU is easy to operate and effortless to maintain. Our AC Ground Power Unit can be supplied with additional 28.5V DC module for obtaining commercial power voltage for tools, appliances. etc. during aircraft maintenance. it is a feature-rich software built for remote operations of GSE with parameter details, fault alarms, alerts and periodic maintenance schedule.
Application
GPU is used to support the aircrafts in ground to maintain and trouble shoot its basic testing with out start up their engine, This will be designed on the required power of aircraft and this whole system is operated by diesel engine , The system is mounted on the portable moving trolley to provide the easy accessibility all over the ground which is towable with necessary braking system.
Printed Circuit Boards (PCBs) PCB-thermal-test-bench.pptx
Printed Circuit Boards (PCBs) need to go through a series of extensive tests and inspections at each step of the manufacturing process to assure the products meets or exceed specifications.
Reliability decreases exponentially in electronic components due to heat problems. Thermal Air series of thermal testing cycling test systems helps manufacturers design ICs, chips, and PCBs for superior thermal performance.
Specifications
Neometrix Thermal Tester is Temperature Forcing Systems and environmental test chambers provide quality assurance through temperature cycling testing. We have used standard highly reliable FLIR camera for thermal scanning.
Thermal Tester is a mobile thermal testing solution capable of environmental stress testing throughout the semiconductor design, manufacturing, and back-end test processes.
Application
Printed Circuit Boards (PCBs) need to go through a series of extensive tests and inspections at each step of the manufacturing process to assure the products meets or exceed specifications.
Reliability decreases exponentially in electronic components due to heat problems. Thermal Air series of thermal testing cycling test systems helps manufacturers design ICs, chips, and PCBs for superior thermal performance.
Key features
Thermal Tester is having following major features:
(a) Wide angle (min 50 degree horizontal) Infrared imaging camera with 640X480 pixels resolution or better.
(b) Thermal analysis software for hotspot and other faults detection.
(c) Automated enclosure with PCB test fixture for testing of PCB of dimension 16X16 inch or better.
(d) Power supply module with minimum eight relay to provide 230VAC/3A/50Hz and 28VDC/5A or better.
(e) Temperatures measurement range: -20 to 200 degrees Celsius.
Optical-test-bench-for-pcb-and-optic-testing.pptx
Optical test equipment or optical measurement equipment are used to measure and characterize the physical properties of light. The insatiable demand for higher capacity in communication networks has fueled the need for highly precise optical test solutions. In addition, precision optical measurements are essential to optical research applications for Defence communication, mobile communication, environmental sensing, and consumer products.
R&D engineers, academic researchers, manufacturing engineers, and field service personnel depend on precision optical test equipment to ensure design and performance specifications, production quality, and network health. For more than 10 years, Neometrix has delivered quality, consistency, ease of use, and market leadership for optical test applications.
Printed circuit board (PCB) FUNCATIONAL TEST BENCH.pptx
Printed circuit board (PCB) functional tester performs critical validation process performed on manufactured PCBs to verify the board’s functionality meets the original design requirements and specifications. Thorough functional testing helps ensure the reliability and performance of PCBs before deployment.
Testing coverage-
Validate continuity and isolation: Verify electrical connectivity and isolation between traces using in-circuit testing (ICT) and flying probe testing to check for opens and shorts.
Confirm impedance: Match measured impedance of traces and interconnects to design values to prevent signal degradation.
Verify power integrity: Check PCB operation under different power conditions to avoid errors from insufficient power delivery.
Assess signal integrity: Examine signal quality under high-speed conditions to prevent distortion and interference.
Test functionality: Stimulate the PCB with input signals and power to check outputs match expected responses based on design.
Confirm robustness: Subject PCB to temperature cycling, vibration, shock to validate resilience and durability.
Execute regression testing: Retest functionality after modifications to ensure no side effects.
Mobile Test Facility (MTF) - Neometrix Defenece
The proposed Mobile Test Facility (MTF) is a roadworthy self-sufficient test facility for testing of “Expandable Turbo Propulsion system (Expandable Engines) of up to 450kgf class” and is devised for Field Tests at various altitude sites in India ranging from sea level to High Altitudes.
“MTF” is proposed with modular design concept, where in each module is built and rigidly installed on a trailer with pre-designated system based on each modules infrastructure functionally required.
It consists Four Trailer mounted Modules-
1. Mobile Utility Trailer Module
2. Mobile Control Cabin Trailer Module
3. Engine Test Section Unit Trailer Module
4. High Pressure Mobile Compressor unit Module (Under GTRE Scope)
Operational Environment :-
1. Test Site Altitude: - From10 m above MSL to 4522 m above MSL
2. Test Site Temperature: -20°C to +50°C
3. Test Site Atmospheric Pressure: 0.57 Atm to 1 Atm
4. Test Site Humidity: 20% to 80%
Electrical General Requirements:
a. Voltage: 415 v ±10%, 3 phase.
b. Frequency: 50 hz +3%, -6%.
c. Aux voltage: 110 VAC (normal supply).
d. UPS voltage - 230 VAC for PLC Panel.
e. 24 V DC Control Circuits.
f. Main switch with emergency stop function.
g. Illuminated double push-button for ON/OFF.
h. Blue illuminated push-button for fault indication and acknowledgement.
i. Control of the test rig and the test programs via operating computer.
modern-universal-automatic-test-equipment.pptx
MODERN UNIVERSAL AUTOMATIC TEST EQUIPMENT(MUATE) is an equipment which is used to perform automatic measurements on the device, known as unit under test (UUT), device under test (DUT), and evaluate the test results. An MUATE has a computer controlled system that contains many complex test instruments that are capable of automatically testing and diagnosing faults in intricate electronic components, PCBs, Integrated circuits. It can test a large range of electronic devices and systems from ingenious components like resistors, inductors, capacitors to complex compiled electronic systems. To accomplish this intention, we are harnessing JIG/Fixture/ITAs.
MUATE systems designed to decrease the amount of test time needed to verify a particular PCB, Component, LRU.
MUATE contains Five subsystem
(a) JTAG
(b) Bed of Nails
(c) Boundary scan
(d) Data acquisition system
(e) Controller
JTAG helps users with PCB debugging, prototyping, testing and repairing.
By using the Bed of Nails (ICT-In circuit testing) we can check for short, open, resistance, capacitance, inductance, tracks, and many more
Components, with the help of boundary scan Test device pin signals or internal signals can be monitored in real-time without interfering with normal operation.
drive-and-control-automation-system.pptx
A drive and control automation system is designed for Helicopter Main Gear Box (MGB) load test rig. The test rig consists of test rig structure in which the MGB of Advanced Light Helicopter (ALH), drive motor, adapter gear boxes are installed. Supplying all hardware & software required for the drive and control automation system for the test rig.
The test rig is a mechanical closed loop system in which the rated speed of MGB is achieved by motor through lower adaptor gearbox. In order to achieve various loads such as thrust loads, torque load and hydraulic pump loads the hydraulic power packs with actuators will be employed. The hydraulic power packs consist of motor pumps, various process switches, sensors valve, etc. which facilitate remote operation of DAS (Data Acquisition System) of the test rig. An AC alternator which is mounted on MGB is to be loaded through resistive load bank with contactor panel.
HYDRAULIC REFILLING TROLLEY - NEOMETRIX DEFENCE
The HYDRAULIC REFILLING TROLLEY is specially designed and developed for the GROUND REFILLING of oil in aircraft systems. It is used for refilling oil in aircraft system through the supplied pressurized hydraulic oil from the trolley to the aircraft, comprising of a pressurized reservoir, with filtered and de- aerated fluid at flow and pressure characteristics required for testing. The Trolley is suitable for wide range of fighter aircraft, military transport aircraft, and helicopters used in Indian Air Force.
This Hydraulic refilling trolley is basically designed for charging Engine oil (Turbonyc Oil-210,Viscosity- 3.7 cst at 100 Deg Celcius )to AIRCRAFT.
Compressed nitrogen is fed from air bottle (BL) along the flexible hose ,through shutoff valve reducers for building up pressure inside the tanks.
The safety valve releases compressed nitrogen into the atmosphere in case pressure exceeds set value.The working fluid displaced by nitrogen pressure from the tank passes through filters and used for cleaning the fluid of mechanical admixtures and gets through aircraft charging adaptor to the AIRCRAFT.
universal-hydraulic-test-bench-aircrafts .pptx
The Neometrix Engineering Series NE-A0107 Universal Hydraulic Test Stands are designed for testing all kind of hydraulic components in various aircrafts & helicopters of Western/ Russian origin like SU-30, Jaguar, Mirage etc.
This is a WORK HORSE required in every ground support & testing establishment.
Virtually any hydraulic component can be tested on this Test Stand by making right hydraulic & electrical connections. It is also very popular with aviation R&D and Product development establishments.
NE-A0107 is heavily used for testing & validating the actuators, valves, accumulators, pumps, hydraulic motors and the hydraulic power packs. Integral drive and integral dynamometer are provided for testing pumps and motors. The NE-A0107 Series Test
Stands are available configured for use with MIL-H-5606, MIL-H-83282, MIL-H-87257 and MIL-H-46170 Hydraulic fluids. Customized OPTIONS are also available.
Key Features:
Cost-effective (International quality, INDIAN PRICE), accurate, automated, software driven, highly capable test system.
Fully Computerized Test Stand. Manual & Semi-Automatic options also available.
National Instruments PXI Based DAQ with Lab View based software
Operating Pressure: up to 3,000 PSI. Flow: up to 20 GPM. Static Pressure: up to 10,000 PSI.
Pumps drive: 5000 RPM, 200 HP. Dynamometer: 5000 RPM, 200 HP. Electrical DC supplies for power packs: 0-32 VDC, 1000 AMP.
Temperature control of hydraulic test circuits. Chilled Water & Air cooled options available.
Six Clamp Perfect Binding Machine
Machine's Salient Features :This is Multi Clamp Perfect Binding Machine, where 6 book clamps travelling in an oval shaped path and done a binding work in a perfect way. 1. In this spine is in line with the crucial binding systems.2. Milling Cutter Comes With Strip Type Cutter and Separate Waste Exhaust System. 3. Gluing System Which has 2 forward rollers and 1 reverse roller (In-built Heating) gives high Quality binding.4. Calibrated head and tail cut offs to avoid adhesive squeeze out.5. Online creasing attachment with Auto Cover feed makes more sense in production.6. Our machine has Optional feeder tray for manual feeding of gate folded covers.7. 'No book-No cover' system ensures the continuous flow of clamps.8. Height and Pressure adjustable ram for book blocks. 9. Moving type Cam Nipping system ensures perfect nipping cover registration.10. Chute delivery system with built in safety systems.
hydraulic-test-pac-with-chart-recorder.pptx
Hydraulic Test Pac with chart recorder is portable, light weight hydro testing equipment designed for shop floor and onsite pressure testing and generates the chart to monitor the process. The unit is self-contained and powered by compressed air. The System requires a supply of compressed shop air to power the liquid pump. A simple adjustment of the air drive pressure regulator setting determines the final output pressure and the pump will automatically stall when the desired hydraulic pressure is attained. When the pump stalls it consumes no further energy and can remain in stall condition indefinitely.
More from Neometrix_Engineering_Pvt_Ltd (20)
Dynamometer Engine Test Rig for engines parameters RPM
Dynamometer Engine Test Rig for engines parameters RPM
TEST RIG FOR HYDRAULIC FLUID (A3987) - NEOMETRIX DEFENCE
TEST RIG FOR HYDRAULIC FLUID (A3987) - NEOMETRIX DEFENCE
Printed Circuit Boards (PCBs) PCB-thermal-test-bench.pptx
Printed Circuit Boards (PCBs) PCB-thermal-test-bench.pptx
Printed circuit board (PCB) FUNCATIONAL TEST BENCH.pptx
Printed circuit board (PCB) FUNCATIONAL TEST BENCH.pptx
Recently uploaded
DEEP LEARNING FOR SMART GRID INTRUSION DETECTION: A HYBRID CNN-LSTM-BASED MODEL
As digital technology becomes more deeply embedded in power systems, protecting the communication
networks of Smart Grids (SG) has emerged as a critical concern. Distributed Network Protocol 3 (DNP3)
represents a multi-tiered application layer protocol extensively utilized in Supervisory Control and Data
Acquisition (SCADA)-based smart grids to facilitate real-time data gathering and control functionalities.
Robust Intrusion Detection Systems (IDS) are necessary for early threat detection and mitigation because
of the interconnection of these networks, which makes them vulnerable to a variety of cyberattacks. To
solve this issue, this paper develops a hybrid Deep Learning (DL) model specifically designed for intrusion
detection in smart grids. The proposed approach is a combination of the Convolutional Neural Network
(CNN) and the Long-Short-Term Memory algorithms (LSTM). We employed a recent intrusion detection
dataset (DNP3), which focuses on unauthorized commands and Denial of Service (DoS) cyberattacks, to
train and test our model. The results of our experiments show that our CNN-LSTM method is much better
at finding smart grid intrusions than other deep learning algorithms used for classification. In addition,
our proposed approach improves accuracy, precision, recall, and F1 score, achieving a high detection
accuracy rate of 99.50%.
ACEP Magazine edition 4th launched on 05.06.2024
This document provides information about the third edition of the magazine "Sthapatya" published by the Association of Civil Engineers (Practicing) Aurangabad. It includes messages from current and past presidents of ACEP, memories and photos from past ACEP events, information on life time achievement awards given by ACEP, and a technical article on concrete maintenance, repairs and strengthening. The document highlights activities of ACEP and provides a technical educational article for members.
Eric Nizeyimana's document 2006 from gicumbi to ttc nyamata handball play
this notes have been created
by Eric36 at nyamata ttc
after readings
pe book for y2sme .
Electric vehicle and photovoltaic advanced roles in enhancing the financial p...
Climate change's impact on the planet forced the United Nations and governments to promote green energies and electric transportation. The deployments of photovoltaic (PV) and electric vehicle (EV) systems gained stronger momentum due to their numerous advantages over fossil fuel types. The advantages go beyond sustainability to reach financial support and stability. The work in this paper introduces the hybrid system between PV and EV to support industrial and commercial plants. This paper covers the theoretical framework of the proposed hybrid system including the required equation to complete the cost analysis when PV and EV are present. In addition, the proposed design diagram which sets the priorities and requirements of the system is presented. The proposed approach allows setup to advance their power stability, especially during power outages. The presented information supports researchers and plant owners to complete the necessary analysis while promoting the deployment of clean energy. The result of a case study that represents a dairy milk farmer supports the theoretical works and highlights its advanced benefits to existing plants. The short return on investment of the proposed approach supports the paper's novelty approach for the sustainable electrical system. In addition, the proposed system allows for an isolated power setup without the need for a transmission line which enhances the safety of the electrical network
Comparative analysis between traditional aquaponics and reconstructed aquapon...
The aquaponic system of planting is a method that does not require soil usage. It is a method that only needs water, fish, lava rocks (a substitute for soil), and plants. Aquaponic systems are sustainable and environmentally friendly. Its use not only helps to plant in small spaces but also helps reduce artificial chemical use and minimizes excess water use, as aquaponics consumes 90% less water than soil-based gardening. The study applied a descriptive and experimental design to assess and compare conventional and reconstructed aquaponic methods for reproducing tomatoes. The researchers created an observation checklist to determine the significant factors of the study. The study aims to determine the significant difference between traditional aquaponics and reconstructed aquaponics systems propagating tomatoes in terms of height, weight, girth, and number of fruits. The reconstructed aquaponics system’s higher growth yield results in a much more nourished crop than the traditional aquaponics system. It is superior in its number of fruits, height, weight, and girth measurement. Moreover, the reconstructed aquaponics system is proven to eliminate all the hindrances present in the traditional aquaponics system, which are overcrowding of fish, algae growth, pest problems, contaminated water, and dead fish.
Redefining brain tumor segmentation: a cutting-edge convolutional neural netw...
Medical image analysis has witnessed significant advancements with deep learning techniques. In the domain of brain tumor segmentation, the ability to
precisely delineate tumor boundaries from magnetic resonance imaging (MRI)
scans holds profound implications for diagnosis. This study presents an ensemble convolutional neural network (CNN) with transfer learning, integrating
the state-of-the-art Deeplabv3+ architecture with the ResNet18 backbone. The
model is rigorously trained and evaluated, exhibiting remarkable performance
metrics, including an impressive global accuracy of 99.286%, a high-class accuracy of 82.191%, a mean intersection over union (IoU) of 79.900%, a weighted
IoU of 98.620%, and a Boundary F1 (BF) score of 83.303%. Notably, a detailed comparative analysis with existing methods showcases the superiority of
our proposed model. These findings underscore the model’s competence in precise brain tumor localization, underscoring its potential to revolutionize medical
image analysis and enhance healthcare outcomes. This research paves the way
for future exploration and optimization of advanced CNN models in medical
imaging, emphasizing addressing false positives and resource efficiency.
TIME DIVISION MULTIPLEXING TECHNIQUE FOR COMMUNICATION SYSTEM
Time Division Multiplexing (TDM) is a method of transmitting multiple signals over a single communication channel by dividing the signal into many segments, each having a very short duration of time. These time slots are then allocated to different data streams, allowing multiple signals to share the same transmission medium efficiently. TDM is widely used in telecommunications and data communication systems.
### How TDM Works
1. **Time Slots Allocation**: The core principle of TDM is to assign distinct time slots to each signal. During each time slot, the respective signal is transmitted, and then the process repeats cyclically. For example, if there are four signals to be transmitted, the TDM cycle will divide time into four slots, each assigned to one signal.
2. **Synchronization**: Synchronization is crucial in TDM systems to ensure that the signals are correctly aligned with their respective time slots. Both the transmitter and receiver must be synchronized to avoid any overlap or loss of data. This synchronization is typically maintained by a clock signal that ensures time slots are accurately aligned.
3. **Frame Structure**: TDM data is organized into frames, where each frame consists of a set of time slots. Each frame is repeated at regular intervals, ensuring continuous transmission of data streams. The frame structure helps in managing the data streams and maintaining the synchronization between the transmitter and receiver.
4. **Multiplexer and Demultiplexer**: At the transmitting end, a multiplexer combines multiple input signals into a single composite signal by assigning each signal to a specific time slot. At the receiving end, a demultiplexer separates the composite signal back into individual signals based on their respective time slots.
### Types of TDM
1. **Synchronous TDM**: In synchronous TDM, time slots are pre-assigned to each signal, regardless of whether the signal has data to transmit or not. This can lead to inefficiencies if some time slots remain empty due to the absence of data.
2. **Asynchronous TDM (or Statistical TDM)**: Asynchronous TDM addresses the inefficiencies of synchronous TDM by allocating time slots dynamically based on the presence of data. Time slots are assigned only when there is data to transmit, which optimizes the use of the communication channel.
### Applications of TDM
- **Telecommunications**: TDM is extensively used in telecommunication systems, such as in T1 and E1 lines, where multiple telephone calls are transmitted over a single line by assigning each call to a specific time slot.
- **Digital Audio and Video Broadcasting**: TDM is used in broadcasting systems to transmit multiple audio or video streams over a single channel, ensuring efficient use of bandwidth.
- **Computer Networks**: TDM is used in network protocols and systems to manage the transmission of data from multiple sources over a single network medium.
### Advantages of TDM
- **Efficient Use of Bandwidth**: TDM all
哪里办理(csu毕业证书)查尔斯特大学毕业证硕士学历原版一模一样
原版一模一样【微信：741003700 】【(csu毕业证书)查尔斯特大学毕业证硕士学历】【微信：741003700 】学位证，留信认证（真实可查，永久存档）offer、雅思、外壳等材料/诚信可靠,可直接看成品样本，帮您解决无法毕业带来的各种难题！外壳，原版制作，诚信可靠，可直接看成品样本。行业标杆！精益求精，诚心合作，真诚制作！多年品质 ,按需精细制作，24小时接单,全套进口原装设备。十五年致力于帮助留学生解决难题，包您满意。
本公司拥有海外各大学样板无数，能完美还原海外各大学 Bachelor Diploma degree, Master Degree Diploma
1:1完美还原海外各大学毕业材料上的工艺：水印，阴影底纹，钢印LOGO烫金烫银，LOGO烫金烫银复合重叠。文字图案浮雕、激光镭射、紫外荧光、温感、复印防伪等防伪工艺。材料咨询办理、认证咨询办理请加学历顾问Q/微741003700
留信网认证的作用:
1:该专业认证可证明留学生真实身份
2:同时对留学生所学专业登记给予评定
3:国家专业人才认证中心颁发入库证书
4:这个认证书并且可以归档倒地方
5:凡事获得留信网入网的信息将会逐步更新到个人身份内，将在公安局网内查询个人身份证信息后，同步读取人才网入库信息
6:个人职称评审加20分
7:个人信誉贷款加10分
8:在国家人才网主办的国家网络招聘大会中纳入资料，供国家高端企业选择人才
ISPM 15 Heat Treated Wood Stamps and why your shipping must have one
For International shipping and maritime laws all wood must contain the ISPM 15 Stamp. Here is how and why.
Embedded machine learning-based road conditions and driving behavior monitoring
Car accident rates have increased in recent years, resulting in losses in human lives, properties, and other financial costs. An embedded machine learning-based system is developed to address this critical issue. The system can monitor road conditions, detect driving patterns, and identify aggressive driving behaviors. The system is based on neural networks trained on a comprehensive dataset of driving events, driving styles, and road conditions. The system effectively detects potential risks and helps mitigate the frequency and impact of accidents. The primary goal is to ensure the safety of drivers and vehicles. Collecting data involved gathering information on three key road events: normal street and normal drive, speed bumps, circular yellow speed bumps, and three aggressive driving actions: sudden start, sudden stop, and sudden entry. The gathered data is processed and analyzed using a machine learning system designed for limited power and memory devices. The developed system resulted in 91.9% accuracy, 93.6% precision, and 92% recall. The achieved inference time on an Arduino Nano 33 BLE Sense with a 32-bit CPU running at 64 MHz is 34 ms and requires 2.6 kB peak RAM and 139.9 kB program flash memory, making it suitable for resource-constrained embedded systems.
Understanding Inductive Bias in Machine Learning
This presentation explores the concept of inductive bias in machine learning. It explains how algorithms come with built-in assumptions and preferences that guide the learning process. You'll learn about the different types of inductive bias and how they can impact the performance and generalizability of machine learning models.
The presentation also covers the positive and negative aspects of inductive bias, along with strategies for mitigating potential drawbacks. We'll explore examples of how bias manifests in algorithms like neural networks and decision trees.
By understanding inductive bias, you can gain valuable insights into how machine learning models work and make informed decisions when building and deploying them.
KuberTENes Birthday Bash Guadalajara - K8sGPT first impressions
K8sGPT is a tool that analyzes and diagnoses Kubernetes clusters. This presentation was used to share the requirements and dependencies to deploy K8sGPT in a local environment.
22CYT12-Unit-V-E Waste and its Management.ppt
Introduction- e - waste – definition - sources of e-waste– hazardous substances in e-waste - effects of e-waste on environment and human health- need for e-waste management– e-waste handling rules - waste minimization techniques for managing e-waste – recycling of e-waste - disposal treatment methods of e- waste – mechanism of extraction of precious metal from leaching solution-global Scenario of E-waste – E-waste in India- case studies.
5214-1693458878915-Unit 6 2023 to 2024 academic year assignment (AutoRecovere...
Bigdata of technology
Recently uploaded (20)
DEEP LEARNING FOR SMART GRID INTRUSION DETECTION: A HYBRID CNN-LSTM-BASED MODEL
DEEP LEARNING FOR SMART GRID INTRUSION DETECTION: A HYBRID CNN-LSTM-BASED MODEL
Eric Nizeyimana's document 2006 from gicumbi to ttc nyamata handball play
Eric Nizeyimana's document 2006 from gicumbi to ttc nyamata handball play
Electric vehicle and photovoltaic advanced roles in enhancing the financial p...
Electric vehicle and photovoltaic advanced roles in enhancing the financial p...
Comparative analysis between traditional aquaponics and reconstructed aquapon...
Comparative analysis between traditional aquaponics and reconstructed aquapon...
Redefining brain tumor segmentation: a cutting-edge convolutional neural netw...
Redefining brain tumor segmentation: a cutting-edge convolutional neural netw...
TIME DIVISION MULTIPLEXING TECHNIQUE FOR COMMUNICATION SYSTEM
TIME DIVISION MULTIPLEXING TECHNIQUE FOR COMMUNICATION SYSTEM
ISPM 15 Heat Treated Wood Stamps and why your shipping must have one
ISPM 15 Heat Treated Wood Stamps and why your shipping must have one
ML Based Model for NIDS MSc Updated Presentation.v2.pptx
ML Based Model for NIDS MSc Updated Presentation.v2.pptx
Embedded machine learning-based road conditions and driving behavior monitoring
Embedded machine learning-based road conditions and driving behavior monitoring
Manufacturing Process of molasses based distillery ppt.pptx
Manufacturing Process of molasses based distillery ppt.pptx
KuberTENes Birthday Bash Guadalajara - K8sGPT first impressions
KuberTENes Birthday Bash Guadalajara - K8sGPT first impressions
5214-1693458878915-Unit 6 2023 to 2024 academic year assignment (AutoRecovere...
5214-1693458878915-Unit 6 2023 to 2024 academic year assignment (AutoRecovere...
Test Rig For IRAB Brake System
- 3. The system is designed to test the performance/Functional testing of the following 18 types of pneumatic valves of IRAB Brake system for for electric locomotives. The system is consisting Brake Pipe, Auxiliary Reservoir, Brake Cylinder Reservoir and Control Reservoir. The test stand have a structure composed of SS –Section with pressure gauges construction housing with digital pressure gauges at front of the stand. The right and left side and the rear side of the test stand is provided with detachable covers and doors. All the air reservoirs and pneumatic piping are accommodated inside of the test stand. The test stand operation is controlled by the computer system by means of predefined software.
- 5. Medium = Compressed Air Pressure Rating = 10.5 Kg/cm2 Air supply Pressure Range = 8-10 Kg/cm2 Flow Rate = 70CFM (2000 LPM) Temperature Range = Ambient up to 48°c Power Supply = 230V + 10% -10% Single Phase 50 HZ
- 7. The system is designed to test the performance/Functional testing of the following 18 types of pneumatic valves of IRAB Brake system for for electric locomotives. The system is consisting Brake Pipe, Auxiliary Reservoir, Brake Cylinder Reservoir and Control Reservoir.
- 9. A9Automatic brake valves C2W Relay Valve C2W Relay Valve-6mm Chock MU-2B Valve F-1 Selector Valve N-1 Reducing Valve FeedValveC2N/FT1/Combined Feed Valve C2W Distributor Valve Duplex Check Valve GM Type Drain Valve
- 11. Thank You