Sewage Pumps and Their Uses
•Download as PPTX, PDF•
1 like•2,021 views
A sewage pump is located in the bottom of basin. It is a device used to move liquids with solids all over a sewer system. Sewage Pumps designed to drain out wasted liquids and semi-solids that contaminated in the home basements and other secluded areas. Here Pumpkart.com sharing the more information about the sewage pumps and their uses that can helps to increase your knowledge about these. Read and choose a sewage pump as per your necessities from Pumpkart
Report
Share
Report
Share
Recommended
Pipe appuretenances, valves and fittings
Valves are used to control water flow, regulate pressure, release air, and prevent backflow. Common types include gate valves, check valves, safety valves, air valves, drain valves, butterfly valves, and globe valves. Fire hydrants tap into water mains and are spaced every 100-300 meters to provide water for firefighting, street washing, gardening, and flushing sewer lines. Hoses can be connected to hydrants and engines used to increase water pressure and flow. Hydrants should be inexpensive, easy to connect and disconnect from hoses, and supply sufficient water, coming in post or flush types.
Estimation of storm sewage
This presentation includes the estimation of storm sewage generated as a result of storm/rainfall events. It includes the detailed usage of rational formula for quantity estimation with solved examples.
Plain sedimentation
This document discusses two types of sedimentation processes: plain sedimentation and sedimentation with coagulation. Plain sedimentation involves separating impurities from water through natural gravitational forces alone, without chemical additives. This process lightens the load on subsequent treatment steps and reduces costs. Sedimentation occurs as particles heavier than water settle out due to gravity. Sedimentation tanks come in various shapes and sizes, and different zones exist within the tanks. Aeration is discussed as well, including its purposes and different aerator types like cascade, spray, and air diffusers. Design criteria and an example calculation for sedimentation tank sizing is also provided.
Design and construction of sewer
The document discusses the design and construction of sewers. It outlines the objectives, which are to understand sewer design procedures, types of sewers, materials used, and construction. It covers sewer shapes, design criteria including discharge, velocity, size and grades. Hydraulic formulae and elements for circular and partially full sewers are provided. Common sewer materials like concrete, steel, plastic, vitrified clay and their properties are described.
Sedimentation Tanks: Design and Working
The document discusses sedimentation in water treatment. It defines sedimentation as the gravitational accumulation of solids at the bottom of water. It then discusses factors that affect sedimentation rates such as particle size and shape, water viscosity, and temperature. Stokes' formula and other equations for calculating particle settling velocity are provided. The main types of sedimentation tanks - quiescent/fill and draw, horizontal flow rectangular and circular, and vertical flow - are described. Key design considerations like surface overflow rate and detention period are also summarized. Finally, the need for periodic sludge removal from sedimentation tanks is mentioned.
Sewerage System
Deals with sewerage and sewerage types and storm water drainage system. Design of sewers and storm sewers is also included in this presentation
Canal irrigation
This presentation discusses about the different types of canals and and also different components of canals.
SEWERAGE SYSTEMS ppt by mayank oza
The document discusses three common sewerage systems:
1. Combined system - Carries both sewage and stormwater in a single sewer, reducing costs but increasing treatment loads.
2. Separate system - Uses two separate sewer systems for sewage and stormwater, reducing treatment loads but increasing costs.
3. Partially separate system - Admits early stormwater runoff but diverts excess, combining advantages of combined and separate systems while requiring stormwater overflows. The document provides details on the advantages and disadvantages of each system.
Recommended
Pipe appuretenances, valves and fittings
Valves are used to control water flow, regulate pressure, release air, and prevent backflow. Common types include gate valves, check valves, safety valves, air valves, drain valves, butterfly valves, and globe valves. Fire hydrants tap into water mains and are spaced every 100-300 meters to provide water for firefighting, street washing, gardening, and flushing sewer lines. Hoses can be connected to hydrants and engines used to increase water pressure and flow. Hydrants should be inexpensive, easy to connect and disconnect from hoses, and supply sufficient water, coming in post or flush types.
Estimation of storm sewage
This presentation includes the estimation of storm sewage generated as a result of storm/rainfall events. It includes the detailed usage of rational formula for quantity estimation with solved examples.
Plain sedimentation
This document discusses two types of sedimentation processes: plain sedimentation and sedimentation with coagulation. Plain sedimentation involves separating impurities from water through natural gravitational forces alone, without chemical additives. This process lightens the load on subsequent treatment steps and reduces costs. Sedimentation occurs as particles heavier than water settle out due to gravity. Sedimentation tanks come in various shapes and sizes, and different zones exist within the tanks. Aeration is discussed as well, including its purposes and different aerator types like cascade, spray, and air diffusers. Design criteria and an example calculation for sedimentation tank sizing is also provided.
Design and construction of sewer
The document discusses the design and construction of sewers. It outlines the objectives, which are to understand sewer design procedures, types of sewers, materials used, and construction. It covers sewer shapes, design criteria including discharge, velocity, size and grades. Hydraulic formulae and elements for circular and partially full sewers are provided. Common sewer materials like concrete, steel, plastic, vitrified clay and their properties are described.
Sedimentation Tanks: Design and Working
The document discusses sedimentation in water treatment. It defines sedimentation as the gravitational accumulation of solids at the bottom of water. It then discusses factors that affect sedimentation rates such as particle size and shape, water viscosity, and temperature. Stokes' formula and other equations for calculating particle settling velocity are provided. The main types of sedimentation tanks - quiescent/fill and draw, horizontal flow rectangular and circular, and vertical flow - are described. Key design considerations like surface overflow rate and detention period are also summarized. Finally, the need for periodic sludge removal from sedimentation tanks is mentioned.
Sewerage System
Deals with sewerage and sewerage types and storm water drainage system. Design of sewers and storm sewers is also included in this presentation
Canal irrigation
This presentation discusses about the different types of canals and and also different components of canals.
SEWERAGE SYSTEMS ppt by mayank oza
The document discusses three common sewerage systems:
1. Combined system - Carries both sewage and stormwater in a single sewer, reducing costs but increasing treatment loads.
2. Separate system - Uses two separate sewer systems for sewage and stormwater, reducing treatment loads but increasing costs.
3. Partially separate system - Admits early stormwater runoff but diverts excess, combining advantages of combined and separate systems while requiring stormwater overflows. The document provides details on the advantages and disadvantages of each system.
Collection and estimation of sewage
Different types of sewers, design period, variations in sewage flow,
estimation of waste water discharge.
water distribution system
This document discusses water distribution systems. It describes how distribution systems deliver water to consumers with appropriate quality, quantity, and pressure. It also classifies different types of distribution networks like dead end, radial, grid iron and ring systems. The document explains the requirements for a good distribution system and different methods of water distribution like gravity, pumping and combined systems. It provides details on distribution reservoirs, types of reservoirs, tanks and pipes used in distribution systems.
Laying and Testing of sewer
This document provides information on various steps involved in sewer design and laying, including:
1) Detailed mapping and marking of the pipe line route, center line, and offset line is required before excavation.
2) Trenches are excavated according to the pipe diameter and depth, and timbering is used for trench stability when depths exceed 2m.
3) The trench bottom is shaped to the design invert level and dewatering is done if needed.
4) Pipes are laid from the lowest point with sockets upstream and joints are made with lead caulking or cement mortar. Testing ensures no leaks or obstructions, and backfilling is done in layers after completion.
Laying, jointing and testing of pipes
This document discusses various types of pipe joints used in water supply systems. It describes bell and spigot joints, expansion joints, flanged joints, mechanical joints, flexible joints, screwed joints, collar joints, and A.C. pipe joints. For each type of joint it provides details on the purpose, construction, and materials used. The document also covers topics like pipe laying works, testing of pipe lines, hydraulic design of pipe networks, and appurtenances in pipe lines.
Plain sedimentation tanks ,Types & Design considerations
Sedimentation is an effective techniques involved for treatment of waste water . Various sedimentation techniques are employed world wide for the purpose.
Plain sedimentation is the simplest technique involving quiescent settling or storage of water, such as would take place in a reservoir, lake, or basin, without the aid of chemicals, preferably for a month or longer, particularly if the source water is a sewage-polluted river water.
This presentation covers various plain sedimentation tanks & design considerations of the same .
If you like it ,Please press the thumb up button & donot forget to give your feedback in comments section, it would be extremely valuable . Any query ? Feel free to post in comments section. All the best ! Enjoy !
Hydrology ( Measurement of rainfall )
This document discusses types of rain gauges used to measure rainfall. It describes non-automatic/non-recording rain gauges like Symon's rain gauge which collect rainfall manually. It also describes automatic/recording rain gauges like weighing bucket, tipping bucket, and float type gauges that record rainfall continuously without manual measurement. Recording gauges provide rainfall intensity over time through a pen on a rotating drum, while non-recording gauges only give total rainfall. Recording gauges do not require an attendant but are more expensive and prone to mechanical faults.
Water distribution system
Layout of distribution networks, methods of water distribution, storage
capacity of ESR, and underground service reservoir.
Lined canal ppt
The document discusses canal lining, which involves providing an impervious layer along the bed and sides of a canal. This increases the life, discharge, and efficiency of the channel. The main types of lining discussed are precast concrete, brick, and stone block lining. The advantages are preventing seepage, waterlogging, increasing capacity and channel life. The disadvantages include high initial costs and difficulty repairing damage. The document evaluates factors like economy, durability in selecting the appropriate lining type.
Diversion Headworks
Diversion headworks are structures constructed at the head of a canal to divert river water into the canal. They include components like weirs, barrages, canal head regulators, divide walls, fish ladders, and guide banks. The objectives are to raise water levels, control silt entry, regulate water flow, and allow fish passage. Proper site selection and design are needed to prevent failures from subsurface water flow, uplift pressure, hydraulic jumps, or scouring during floods. Remedies include increasing seepage lengths, adding sheet piles, and using thicker impervious floors.
Water and Waste Water Engineering
This document discusses methods for estimating stormwater runoff in urban areas. It begins by defining stormwater as water from rain, snow, or ice that flows over surfaces after falling to the ground. The rational method and empirical formulas are presented as common approaches to estimating peak stormwater discharge rates. The rational method estimates discharge as a function of rainfall intensity, runoff coefficient, and drainage area. Runoff coefficients vary based on surface type. An example problem applies the rational method to calculate sewage flow and stormwater flow for a drainage system.
05 water supply system
The document discusses water supply systems including water transmission and distribution. It describes the key components and design considerations for extracting, treating, storing, pumping and conveying water from its source through treatment, transmission, storage, and distribution to end users. The transmission system conveys treated or untreated water from sources to the distribution system through treatment plants and storage reservoirs using pipelines, tunnels, canals or aqueducts. The distribution system then supplies adequate water at sufficient pressure to individual consumers through a pipe network with valves and service connections.
Dewatering techniques
Dewatering is the process of removing water from construction sites to allow excavation work to be done safely and efficiently below the water table. There are several reasons why dewatering is needed, including providing a dry work area, improving stability, and increasing safety. Common dewatering techniques include sump pumping, well points, deep wells, and trenches. Each method has advantages and disadvantages depending on the site conditions and depth of water lowering required. Proper planning and design of a dewatering system is important to effectively control groundwater and allow construction work to progress smoothly.
Disposal of sewage on land
This document discusses land disposal of sewage and the standards for wastewater effluents that are discharged onto land for irrigation. It outlines the Bureau of Indian Standards quality standards that set limits on pollutants in wastewater used for irrigation. Land disposal is appropriate when natural waterways are not nearby, irrigation water is scarce, or rainfall is low. The document describes different techniques for irrigating crops with sewage and measures to prevent "sewage sickness" of the land from overuse.
M.i tank
This document describes the design of an earthen bund and associated structures for a minor irrigation project in India. It includes details on:
1. Selecting the site for the bund based on factors like water storage capacity, foundation stability, and construction material availability.
2. Surveying the reservoir area to determine capacity contours and reservoir capacity.
3. Designing the earthen bund with specifications for material used, slopes, and dimensions based on dam height.
4. Calculating water requirements for irrigation based on crop areas and duties.
5. Designing associated structures like the canal with a trapezoidal section, sluice gate size based on discharge requirements,
Spillway gates
Spillway crest gates are adjustable gates used to control water flow in reservoir and river systems. They act as barriers to store additional water, allowing the height of dams to be increased and requiring more land acquisition. The main types of spillway gates are dripping shutters, stop logs, radial/tainter gates, drum gates, and vertical lift/rectangle gates. Vertical lift gates are rectangular gates that spin horizontally between grooved piers and can be raised or lowered by a hoisting mechanism to control water flow.
Canal outlets
Regulation works are structures constructed to regulate water flow in canals. The main types are head regulators, cross regulators, canal escapes, and canal outlets. Head regulators control water entry into off-taking channels from parent channels. Cross regulators are located downstream of off-takes and help control water levels and closures for repairs. Canal outlets connect distribution channels to field channels and supply water to irrigation fields at regulated discharges.
L 9 aeration
Environmental Engineering-I (Water Supply Engg.) - TE (CIVIL)
Course material by PROF S S JAHAGIRDAR, NKOCET, SOLAPUR.
Canal outlets and modules
This document discusses different types of canal outlets used to release water from distributing channels into watercourses. It describes non-modular, semi-modular, and modular outlets. Non-modular outlets discharge based on water level differences, while modular outlets discharge independently of water levels. Semi-modular outlets discharge depending on the channel water level but not the watercourse level. Specific outlet types are also defined, such as pipe outlets, open sluice, and Gibbs, Khanna, and Foote rigid modules. Discharge equations for different outlet types are provided.
Water demand and factor affecting water demand
The document discusses different types of water demand - domestic, public, industrial, commercial, fire, and losses/waste. It provides estimated per capita daily demand amounts for each type according to Indian standards. Factors that affect water demand are also outlined, such as city size, climate, cost of water, distribution systems, supply systems, industries present, water quality, and living habits. Formulas to calculate firefighting water requirements based on population are also presented.
Conveyance of-water
This document provides an overview of conveying water through pipelines. It discusses different types of pipe materials like cast iron, ductile iron, steel, concrete, galvanized iron and plastic pipes. The key requirements of good pipe materials are described as structural strength, durability, corrosion resistance, imperviousness, smoothness and cost. Different pipe joining methods like socket and spigot, flanged, screwed and expansion joints are also outlined. Finally, the major steps involved in laying pipes like setting out and trench excavation are briefly mentioned.
pumps and its types-ppt
This document discusses different types of pumps, including their classifications, characteristics, applications, and performance. It describes hydrodynamic/non-positive displacement pumps, which use flow to transfer fluid at relatively low pressure and are generally used for low pressure, high volume applications. It also describes hydrostatic/positive displacement pumps, which have close-fitting components and can create high pressures, making them self-priming. Specific positive displacement pump types like gear, vane, piston and centrifugal pumps are examined in terms of their applications and operating principles. Pump efficiencies including volumetric, mechanical and overall efficiency are also covered.
Foremost Pump
Foremost Pump & Well Services LLC owns a 60 Ton SEMCO pump rig. The document discusses Foremost Pump & Well Services LLC and their disassembling of an oil tube with their 60 Ton SEMCO pump rig.
More Related Content
What's hot
Collection and estimation of sewage
Different types of sewers, design period, variations in sewage flow,
estimation of waste water discharge.
water distribution system
This document discusses water distribution systems. It describes how distribution systems deliver water to consumers with appropriate quality, quantity, and pressure. It also classifies different types of distribution networks like dead end, radial, grid iron and ring systems. The document explains the requirements for a good distribution system and different methods of water distribution like gravity, pumping and combined systems. It provides details on distribution reservoirs, types of reservoirs, tanks and pipes used in distribution systems.
Laying and Testing of sewer
This document provides information on various steps involved in sewer design and laying, including:
1) Detailed mapping and marking of the pipe line route, center line, and offset line is required before excavation.
2) Trenches are excavated according to the pipe diameter and depth, and timbering is used for trench stability when depths exceed 2m.
3) The trench bottom is shaped to the design invert level and dewatering is done if needed.
4) Pipes are laid from the lowest point with sockets upstream and joints are made with lead caulking or cement mortar. Testing ensures no leaks or obstructions, and backfilling is done in layers after completion.
Laying, jointing and testing of pipes
This document discusses various types of pipe joints used in water supply systems. It describes bell and spigot joints, expansion joints, flanged joints, mechanical joints, flexible joints, screwed joints, collar joints, and A.C. pipe joints. For each type of joint it provides details on the purpose, construction, and materials used. The document also covers topics like pipe laying works, testing of pipe lines, hydraulic design of pipe networks, and appurtenances in pipe lines.
Plain sedimentation tanks ,Types & Design considerations
Sedimentation is an effective techniques involved for treatment of waste water . Various sedimentation techniques are employed world wide for the purpose.
Plain sedimentation is the simplest technique involving quiescent settling or storage of water, such as would take place in a reservoir, lake, or basin, without the aid of chemicals, preferably for a month or longer, particularly if the source water is a sewage-polluted river water.
This presentation covers various plain sedimentation tanks & design considerations of the same .
If you like it ,Please press the thumb up button & donot forget to give your feedback in comments section, it would be extremely valuable . Any query ? Feel free to post in comments section. All the best ! Enjoy !
Hydrology ( Measurement of rainfall )
This document discusses types of rain gauges used to measure rainfall. It describes non-automatic/non-recording rain gauges like Symon's rain gauge which collect rainfall manually. It also describes automatic/recording rain gauges like weighing bucket, tipping bucket, and float type gauges that record rainfall continuously without manual measurement. Recording gauges provide rainfall intensity over time through a pen on a rotating drum, while non-recording gauges only give total rainfall. Recording gauges do not require an attendant but are more expensive and prone to mechanical faults.
Water distribution system
Layout of distribution networks, methods of water distribution, storage
capacity of ESR, and underground service reservoir.
Lined canal ppt
The document discusses canal lining, which involves providing an impervious layer along the bed and sides of a canal. This increases the life, discharge, and efficiency of the channel. The main types of lining discussed are precast concrete, brick, and stone block lining. The advantages are preventing seepage, waterlogging, increasing capacity and channel life. The disadvantages include high initial costs and difficulty repairing damage. The document evaluates factors like economy, durability in selecting the appropriate lining type.
Diversion Headworks
Diversion headworks are structures constructed at the head of a canal to divert river water into the canal. They include components like weirs, barrages, canal head regulators, divide walls, fish ladders, and guide banks. The objectives are to raise water levels, control silt entry, regulate water flow, and allow fish passage. Proper site selection and design are needed to prevent failures from subsurface water flow, uplift pressure, hydraulic jumps, or scouring during floods. Remedies include increasing seepage lengths, adding sheet piles, and using thicker impervious floors.
Water and Waste Water Engineering
This document discusses methods for estimating stormwater runoff in urban areas. It begins by defining stormwater as water from rain, snow, or ice that flows over surfaces after falling to the ground. The rational method and empirical formulas are presented as common approaches to estimating peak stormwater discharge rates. The rational method estimates discharge as a function of rainfall intensity, runoff coefficient, and drainage area. Runoff coefficients vary based on surface type. An example problem applies the rational method to calculate sewage flow and stormwater flow for a drainage system.
05 water supply system
The document discusses water supply systems including water transmission and distribution. It describes the key components and design considerations for extracting, treating, storing, pumping and conveying water from its source through treatment, transmission, storage, and distribution to end users. The transmission system conveys treated or untreated water from sources to the distribution system through treatment plants and storage reservoirs using pipelines, tunnels, canals or aqueducts. The distribution system then supplies adequate water at sufficient pressure to individual consumers through a pipe network with valves and service connections.
Dewatering techniques
Dewatering is the process of removing water from construction sites to allow excavation work to be done safely and efficiently below the water table. There are several reasons why dewatering is needed, including providing a dry work area, improving stability, and increasing safety. Common dewatering techniques include sump pumping, well points, deep wells, and trenches. Each method has advantages and disadvantages depending on the site conditions and depth of water lowering required. Proper planning and design of a dewatering system is important to effectively control groundwater and allow construction work to progress smoothly.
Disposal of sewage on land
This document discusses land disposal of sewage and the standards for wastewater effluents that are discharged onto land for irrigation. It outlines the Bureau of Indian Standards quality standards that set limits on pollutants in wastewater used for irrigation. Land disposal is appropriate when natural waterways are not nearby, irrigation water is scarce, or rainfall is low. The document describes different techniques for irrigating crops with sewage and measures to prevent "sewage sickness" of the land from overuse.
M.i tank
This document describes the design of an earthen bund and associated structures for a minor irrigation project in India. It includes details on:
1. Selecting the site for the bund based on factors like water storage capacity, foundation stability, and construction material availability.
2. Surveying the reservoir area to determine capacity contours and reservoir capacity.
3. Designing the earthen bund with specifications for material used, slopes, and dimensions based on dam height.
4. Calculating water requirements for irrigation based on crop areas and duties.
5. Designing associated structures like the canal with a trapezoidal section, sluice gate size based on discharge requirements,
Spillway gates
Spillway crest gates are adjustable gates used to control water flow in reservoir and river systems. They act as barriers to store additional water, allowing the height of dams to be increased and requiring more land acquisition. The main types of spillway gates are dripping shutters, stop logs, radial/tainter gates, drum gates, and vertical lift/rectangle gates. Vertical lift gates are rectangular gates that spin horizontally between grooved piers and can be raised or lowered by a hoisting mechanism to control water flow.
Canal outlets
Regulation works are structures constructed to regulate water flow in canals. The main types are head regulators, cross regulators, canal escapes, and canal outlets. Head regulators control water entry into off-taking channels from parent channels. Cross regulators are located downstream of off-takes and help control water levels and closures for repairs. Canal outlets connect distribution channels to field channels and supply water to irrigation fields at regulated discharges.
L 9 aeration
Environmental Engineering-I (Water Supply Engg.) - TE (CIVIL)
Course material by PROF S S JAHAGIRDAR, NKOCET, SOLAPUR.
Canal outlets and modules
This document discusses different types of canal outlets used to release water from distributing channels into watercourses. It describes non-modular, semi-modular, and modular outlets. Non-modular outlets discharge based on water level differences, while modular outlets discharge independently of water levels. Semi-modular outlets discharge depending on the channel water level but not the watercourse level. Specific outlet types are also defined, such as pipe outlets, open sluice, and Gibbs, Khanna, and Foote rigid modules. Discharge equations for different outlet types are provided.
Water demand and factor affecting water demand
The document discusses different types of water demand - domestic, public, industrial, commercial, fire, and losses/waste. It provides estimated per capita daily demand amounts for each type according to Indian standards. Factors that affect water demand are also outlined, such as city size, climate, cost of water, distribution systems, supply systems, industries present, water quality, and living habits. Formulas to calculate firefighting water requirements based on population are also presented.
Conveyance of-water
This document provides an overview of conveying water through pipelines. It discusses different types of pipe materials like cast iron, ductile iron, steel, concrete, galvanized iron and plastic pipes. The key requirements of good pipe materials are described as structural strength, durability, corrosion resistance, imperviousness, smoothness and cost. Different pipe joining methods like socket and spigot, flanged, screwed and expansion joints are also outlined. Finally, the major steps involved in laying pipes like setting out and trench excavation are briefly mentioned.
What's hot (20)
Plain sedimentation tanks ,Types & Design considerations
Plain sedimentation tanks ,Types & Design considerations
Viewers also liked
pumps and its types-ppt
This document discusses different types of pumps, including their classifications, characteristics, applications, and performance. It describes hydrodynamic/non-positive displacement pumps, which use flow to transfer fluid at relatively low pressure and are generally used for low pressure, high volume applications. It also describes hydrostatic/positive displacement pumps, which have close-fitting components and can create high pressures, making them self-priming. Specific positive displacement pump types like gear, vane, piston and centrifugal pumps are examined in terms of their applications and operating principles. Pump efficiencies including volumetric, mechanical and overall efficiency are also covered.
Foremost Pump
Foremost Pump & Well Services LLC owns a 60 Ton SEMCO pump rig. The document discusses Foremost Pump & Well Services LLC and their disassembling of an oil tube with their 60 Ton SEMCO pump rig.
2 Centifugal Filtration
This document discusses centrifugal filtration and presents concepts through diagrams and text. It describes elements of centrifugal filtration including radial force parallel to the filter face, influent and concentrate channels, and gradients that form during centrifugation. Coriolis, centrifugal, and Euler forces are examined, and it is noted these forces can alleviate filter caking, enhance flux, and reduce energy per unit flux. Design concepts are presented to increase efficiency by increasing the surface area to volume ratio and Coriolis acceleration.
TDLR Well Driller/Pump Installer Program, W.L. Stribling, Project Manager, Te...
TDLR Well Driller/Pump Installer Program, W.L. Stribling, Project Manager, Te...Texas Alliance of Groundwater Districts
This document provides information about Texas' Well Drillers/Pump Installers Abandoned Well Notification and Referral Program. The primary goals of the program are groundwater protection, licensing qualified drillers and installers, establishing well construction and plugging standards, administering abandoned well programs, and cooperating with regulatory agencies. Contact information is provided for the relevant state department. The department website provides information on reporting violations, well construction standards, license applications, rules and statutes, and continuing education courses. Requirements are outlined for driller and installer license designations, apprenticeships, adhering to manufacturer standards, addressing local authority and groundwater districts, variances, well disinfection, and addressing denied access or undesirable waterCentrifugal Pumps
Centrifugal pumps are rotodynamic pumps that use a rotating impeller to increase the pressure of a liquid. The impeller spins and throws liquid outward via centrifugal force, increasing pressure. Key parts include the impeller, casing, suction and delivery pipes. Centrifugal pumps are classified based on impeller shape, working head, number of stages, flow direction, and number of suctions. They work by converting the kinetic energy of the liquid into pressure energy. The minimum speed required for startup depends on the manometric head. Cavitation can occur if the pressure drops below vapor pressure, forming bubbles that collapse and damage surfaces.
Sewer Appurtanances
This presentation deals with the following appurtenances: Manholes; Flushing tanks, flushing manholes and clean outs; Interceptor tanks; (Inverted) siphons; Pumping stations; Gutters, storm water inlets and catch basins, and Other appurtenances.
Boiler equipments
The document describes the key systems of a boiler, including the water and steam system, air/furnace/flue gas system, fuel system, ash system, and utility systems. It provides details on components like the deaerator, boiler feedwater pump, steam drum, superheater, furnace, sootblower, electrostatic precipitator, induced draft fan, and related conveyors, valves, transmitters and more.
Centrifugal pumps
Centrifugal pumps are machines which use centrifugal force to move liquids. In this program, you will learn the principles, parts, and general operation of these pumps, what pump efficiency is, and how head and pressure are calculated.
Maintenance of Pumps
Following presentation consist of a fundamental steps that took place during a pump overhaul.
this presentation will give you the basic idea about maintenance .
Sewerage design
This document discusses the design considerations for sewer systems. It outlines the different types of sewers based on wastewater flow, and specifies design requirements like pipe sizing, slopes, depths, and velocities. Factors like population equivalent calculations, peak flows, hydraulic properties, and manhole levels are also summarized. The document provides guidance on planning and laying out sewer networks in accordance with relevant codes and standards.
Pump
The document provides information about pumps, including:
1) Pumps are mechanical devices that use rotation or reciprocation to move fluid from one place to another by converting energy into hydraulic energy.
2) The main purposes of pumps are to transfer fluid from low to high pressure areas, from low to high elevations, and from local to distant locations.
3) There are two main types of pumps - positive displacement pumps which move a fixed volume of fluid with each cycle, and centrifugal pumps which use centrifugal force to move fluid by spinning an impeller.
Pump Maintenance and Troubleshooting
This document provides guidance on pump maintenance and troubleshooting. It discusses different types of maintenance including fix-on-failure, scheduled, preventive, and predictive maintenance. The document then covers mechanical and hydraulic pump problems, whether internal or external to the pump. Specific issues that could cause problems are identified. The importance of qualitative measurements like sounds and smells is emphasized. Case studies using gauge readings to troubleshoot issues are presented. Maintaining pumps is important to avoid downtime and costs.
Centrifugal pump
The document discusses centrifugal pumps. It describes how centrifugal pumps work by converting mechanical energy to hydraulic energy using centrifugal force. They work on the principle of forced vortex flow. Key components include an impeller that rotates and accelerates the fluid outward, and a casing that captures the fluid and converts its kinetic energy to pressure. Centrifugal pumps are used to pump liquids like water, sewage, petroleum and more. Performance curves are used to predict pump behavior under different operating conditions.
Centrifugal Pump
The document discusses how centrifugal pumps work. It explains that fluid enters the impeller axially and is accelerated radially by centrifugal force, gaining pressure and velocity. The kinetic energy is partly converted to pressure energy in the volute casing. A centrifugal pump has a rotating impeller and stationary volute casing. Impellers can be open, semi-open, or enclosed, and pumps are classified by flow as radial, axial, or mixed. Multi-stage pumps contain multiple impellers to achieve higher pressures.
Pumps and types of pumps in detail
The document discusses different types of pumps used in fluid transport systems. It describes positive displacement pumps which use a fixed volume cavity to trap and transport fluid with each cycle. Dynamic pumps are also discussed, which add momentum to fluid without a fixed volume. Centrifugal pumps are described in detail, with their construction, working principle, performance parameters and efficiency calculations explained. The key aspects covered are the use of impellers to impart energy and velocity to fluid which is then converted to pressure by the volute casing.
PUMPS
Pumps are devices that use mechanical energy to increase the velocity, pressure, or elevation of liquids and gases. There are two main types of pumps: positive displacement pumps and dynamic pumps. Positive displacement pumps apply direct pressure on a liquid using a reciprocating piston or rotating components. Dynamic pumps use centrifugal force to generate high rotational velocities and convert the kinetic energy of liquids into pressure energy. Common positive displacement pump types include piston pumps, plunger pumps, and diaphragm pumps. Common dynamic pump types include centrifugal pumps which contain an impeller and casing. Proper consideration of factors like net positive suction head are important for pump selection and operation.
Basics of pump
This Presentation is about working principle of Pumps.Basic Presentation regarding pumps , will definitely help beginners to learn pump types , their working , their parts etc.
Pumps & pumping systems
This document provides an overview of pumping systems and opportunities for improving their energy efficiency. It discusses the types of pumps commonly used, including centrifugal and positive displacement pumps. The document explains how to assess pump performance by calculating hydraulic power, shaft power, and efficiency. It also outlines several methods for improving energy efficiency, such as selecting the properly sized pump, controlling flow rates through variable speed drives, using parallel pumps to meet varying demand, and eliminating inefficient flow control valves and bypass lines. The overall aim is to educate about pumping systems and identify opportunities to reduce the significant energy demands of pump operations.
Build Features, Not Apps
Presented at Tokyo iOS Meetup https://www.meetup.com/TokyoiOSMeetup/events/234405194/
Video here: https://www.youtube.com/watch?v=lJlyR8chDwo
Viewers also liked (19)
TDLR Well Driller/Pump Installer Program, W.L. Stribling, Project Manager, Te...
TDLR Well Driller/Pump Installer Program, W.L. Stribling, Project Manager, Te...
Similar to Sewage Pumps and Their Uses
Types of groundwater pumps
This document discusses different types of groundwater pumps. It begins by introducing various pump classifications and descriptions. It then focuses on pumps used for groundwater, dividing them into three main categories: 1) hand and treadle pumps which are manually operated, 2) low pressure suction pumps which use suction to pull water from shallow depths, and 3) high pressure suction pumps, which include centrifugal pumps that use rotation to move water and positive displacement pumps that use expanding cavities to move water at constant volumes. The document provides details on the design and operation of centrifugal and positive displacement pumps. It concludes by mentioning submersible pumps and jet pumps as other groundwater pump options.
Vacuum Pump Manufacturer -India
GP is a custom Vacuum Pump manufacturer, industrial vacuum pump, waterrring vacuum pumps exporter, suppliers, India
What Is Drainage Pump? And Why Is It Used?
Drainage pumps are excellent for pumping water and dirty water mixed with light abrasives. The pump is designed to enable convenient transport, installation and handling.
Sump pump
Sump pumps are used to pump water out of basements. There are two main types - submersible pumps, which are fully immersed in water, and surface pumps, which are not immersed. Submersible pumps have advantages like lack of friction and cooling of the engine. Surface pumps can pump from any depth but are harder to maintain. Key manufacturers of sump pumps include Zoeller and Little Giant, which produce reliable pumps using their own components. Sump pumps are used to drain basements, wells, trenches and more, and come in models suited to different applications and water conditions.
Useful Rotary Pump for Your Different Types of Applications
There are different types of rotary pumps used for different applications. Depending upon the type of construction, the design and shape of these pumps are also different. These pumps might be different in the way they are designed but work on the same principle and fall under the same category.
Function and Importance of High Speed Submersible Sewage Pumps
High-speed submersible sewage pumps are designed to pump non-aggressive and non-explosive sewage with solids or fibers at higher speed while fully submerged in the liquid.
What the Application for Automatic Drainage Water Pump
A drainage pump is primarily intended for pumping surface and seepage water to different locations and groundwater.
A Guide on Selecting the Right Drainage Pump for Your Home or Business
Good drainage is key to keeping your home or business safe from flooding, and a drainage pump can be an effective way of ensuring that the water stays away from where it’s not wanted.
Propelling Efficiency: Leading Propeller Pumps Manufacturer in India
Propeller pumps are most commonly used for water transfer and flood control but can handle many fluids and operating conditions.
Hydraulic excavators for construction.pdf
The hydraulic excavator, which is commonly employed in the construction and mining industries, is one such piece of heavy equipment. The excavator's main components are a bucket, arm, rotating cab, and moving tracks, and its activities are controlled by hydraulics.
Hydraulic Excavators
Construction Requirements
Mahaveer Distributors
Hydraulic Excavators
Because of its capacity to handle enormous weights and the power of the control mechanism, hydraulics is used in the majority of heavy-duty equipment. The hydraulic excavator, which is commonly employed in the construction and mining industries, is one such piece of heavy equipment. The excavator's main components are a bucket, arm, rotating cab, and moving tracks, and its activities are controlled by hydraulics. Excavators are used primarily in the construction business to dig ditches, trenches, foundations, and holes, as well as in the mining industry to quarry and mine river beds.
Construction Requirements
The Hoe is constructed with three important parts like boom, dipper arm, and bucket. Undercarriage is an essential part of heavy-equipment that contains other components necessary for the movement of the excavator. Operators can control excavator operations from the cab using travel pedals, levers, and joysticks. Augers, compactors, hammers, rippers, grapples, etc., are some type attachments used in excavators. The cab is the location from where the operator controls the movement of excavator and it needs to offer excellent visibility to the operator. Solid iron or other materials are used as counterweight in excavators to counterbalance the weight of excavated earth. There are high chances for the heavy equipment to tip over during its operation if a proper counterweight is not included.
Important Things You Must Know About Vertical Turbine Pumps in India
A vertical turbine pump is an incredibly flexible sort of divergent pump that has a large number of applications.
Efficient Flow: End Suction Pumps for Various Applications in India
Flowmore Pumps is the company to call if you’re in the market for an end suction pump but have had no luck locating a dependable maker.
A Comprehensive Analysis of Vertical Turbine Pump Types
There is a large selection of vertical turbine pumps on the market, each with unique benefits and drawbacks. It’s totally up to you whatever one works best for you.
Wanner Engineering: a Brief Introduction to Positive Displacement Pumps
Wanner Engineering manufactures and distributes seal-less Hydra-Cell pumps using positive displacement technology. Positive displacement pumps create a constant fluid flow by expanding an intake cavity to draw fluid in and then reducing a discharge cavity to expel the fluid. This steady flow makes positive displacement pumps suitable for difficult to move fluids. Positive displacement pumps come in various sizes and capacities depending on the application, including reciprocating pumps for steady volume flow, metering pumps for low flow rates, and rotary pumps for pressure sensitive systems.
All About Centrifugal Pumps: Simple Explanation
Centrifugal pumps are capable of moving an extensive variability of fluids. It happens under a wide range of conditions. They continue to function for an extended period of time. It can happen due to their resilience.
How Vertical Turbine Pumps Work: Efficient Water Management Solutions
A vertical turbine pump's main function is to transfer fluid from an underground reservoir, pit, or well to an above ground location.
Submersible Sludge Pump : How To Choose The Right Sludge Pump?
Submersible sludge pumps are designed to move viscous, sludgy materials while being fully submerged in the liquid. The pump is engineered precisely to withstand the abrasive nature of sludge to avoid the pump components.
Water Pump Hire An Essential Guide.pdf
Water pumps are essential tools for a variety
of applications, from draining flooded
basements to irrigating crops. However, not
everyone needs to own a water pump
outright. Water pump hire is a great option
for those who only need a pump for a short
period of time or for those who don't have
the storage space for one.
Working & application: Additional pumps of different types
Here, The design, as well as the positions, can be used to identify the pump. To make something more comfortable while looking for high head water pumps manufacturers.
Types of Centrifugal Pumps – Everything You Need to Know
Centrifugal pumps will be found in the major industrial applications. Centrifugal pumps are the most popular and commonly used pumps to move fluids and solid liquids in industrial plants. Ranging from domestic to industrial uses, centrifugal pumps have an extensive range of applications.
Similar to Sewage Pumps and Their Uses (20)
Useful Rotary Pump for Your Different Types of Applications
Useful Rotary Pump for Your Different Types of Applications
Function and Importance of High Speed Submersible Sewage Pumps
Function and Importance of High Speed Submersible Sewage Pumps
What the Application for Automatic Drainage Water Pump
What the Application for Automatic Drainage Water Pump
A Guide on Selecting the Right Drainage Pump for Your Home or Business
A Guide on Selecting the Right Drainage Pump for Your Home or Business
Propelling Efficiency: Leading Propeller Pumps Manufacturer in India
Propelling Efficiency: Leading Propeller Pumps Manufacturer in India
Important Things You Must Know About Vertical Turbine Pumps in India
Important Things You Must Know About Vertical Turbine Pumps in India
Efficient Flow: End Suction Pumps for Various Applications in India
Efficient Flow: End Suction Pumps for Various Applications in India
A Comprehensive Analysis of Vertical Turbine Pump Types
A Comprehensive Analysis of Vertical Turbine Pump Types
Wanner Engineering: a Brief Introduction to Positive Displacement Pumps
Wanner Engineering: a Brief Introduction to Positive Displacement Pumps
How Vertical Turbine Pumps Work: Efficient Water Management Solutions
How Vertical Turbine Pumps Work: Efficient Water Management Solutions
Submersible Sludge Pump : How To Choose The Right Sludge Pump?
Submersible Sludge Pump : How To Choose The Right Sludge Pump?
Working & application: Additional pumps of different types
Working & application: Additional pumps of different types
Types of Centrifugal Pumps – Everything You Need to Know
Types of Centrifugal Pumps – Everything You Need to Know
Sewage Pumps and Their Uses
- 1. Sewage Pumps & Their Uses Submitted by www.pumpkart.com
- 2. What Is a Sewage Pump? Submitted by www.pumpkart.com A sewage pump is located in the bottom of basin. It is a device used to move liquids with solids all over a sewer system.
- 3. Sewage Pumps designed to drain out wasted liquids and semi-solids that contaminated in the home basements and other secluded areas Submitted by www.pumpkart.com
- 4. They Work Automatically The pump switch is activated automatically as the liquid reaches a specific point The pump switches off when the liquid goes down to a certain point Users Safe for functioning Submitted by www.pumpkart.com
- 5. These pumps can be submersed into the liquid Submitted by www.pumpkart.com
- 6. They can work outside a basin Submitted by www.pumpkart.com
- 7. Most of them are efficient to handle up to 2” solids Submitted by www.pumpkart.com
- 8. More powerful pumps need to be used for a higher and longer lifting of the waste Submitted by www.pumpkart.com
- 9. When thinking of buying a pump, don’t forget to take advice from a plumber to select the right horsepower sewage pump! Submitted by www.pumpkart.com
- 10. Horsepower can be calculated by the number of drain outlets connected to the sewage basin Submitted by www.pumpkart.com
- 11. Must Visit at www.pumpkart.com to Buy a Long Lasting Sewage Pump Submitted by www.pumpkart.com