Optimization of Process Parameters of Powder Mixed Wire-cut Electric Discharge Machining on NIMONIC 90 Using Taguchi Method and Grey Relational Analysis
This document summarizes an experiment conducted to optimize the process parameters of powder mixed wire-cut electric discharge machining (PMWEDM) on NIMONIC 90 alloy. The experiment uses a Taguchi L27 orthogonal array to investigate the effects of pulse on time, pulse off time, servo voltage, wire feed rate, and powder concentration on responses like kerf width, material removal rate, and surface roughness. Grey relational analysis is also used for multi-objective optimization. The results show that using the optimized parameters from Taguchi and grey relational analysis can reduce kerf width by 3.27% and surface roughness by 21.85%, while increasing material removal rate.
Development of a Taguchi-based framework for optimizing two quality character...IJERA Editor
A framework based on Taguchi parameter design was developed and successfully demonstrated to optimize two
quality characteristics- surface roughness and angular accuracy in Wire Electrical Discharge Machining (WEDM)
process. An orthogonal array (OA)L9was used in the Taguchi experiment design for four controllable
factors, each with three levels. With one non-controllable factor investigated, 18 experiments were conducted in
the Taguchi-based experiment setting, compared to 3
4
(=81) parameter combination as required by a traditional
DOE setting. Conducted for the two response variables, Taguchi experiments from the case study gave the
optimal combination of pulse on time at 9µs (A1), feed rate at 35 in/min (B2), voltage at 8v (C2), and wire
tension at 165g (D3) for surface roughness optmization, and pulse on time at 13µs (A3), feed rate at 35 in/min
(B2), voltage at 8v (C2), and wire tension at 160g (D2) for angular accuracy optmization. This optimal parameter
setting combination was verified through a confirmation run that confirms the optimal quality responses of
126.1µin for surface roughness and 0.024º for angular accuracy. This research ultimately showed the dual
output variable improvement and the framework established itself as a means to solve similar problems in other
machining applications. The developed framework can serve as guidance for researchers to obtain multivariable
optimal setting in a systematic way.
Development of a Taguchi-based framework for optimizing two quality character...IJERA Editor
A framework based on Taguchi parameter design was developed and successfully demonstrated to optimize two
quality characteristics- surface roughness and angular accuracy in Wire Electrical Discharge Machining (WEDM)
process. An orthogonal array (OA)L9was used in the Taguchi experiment design for four controllable
factors, each with three levels. With one non-controllable factor investigated, 18 experiments were conducted in
the Taguchi-based experiment setting, compared to 34 (=81) parameter combination as required by a traditional
DOE setting. Conducted for the two response variables, Taguchi experiments from the case study gave the
optimal combination of pulse on time at 9μs (A1), feed rate at 35 in/min (B2), voltage at 8v (C2), and wire
tension at 165g (D3) for surface roughness optmization, and pulse on time at 13μs (A3), feed rate at 35 in/min
(B2), voltage at 8v (C2), and wire tension at 160g (D2) for angular accuracy optmization. This optimal parameter
setting combination was verified through a confirmation run that confirms the optimal quality responses of
126.1μin for surface roughness and 0.024º for angular accuracy. This research ultimately showed the dual
output variable improvement and the framework established itself as a means to solve similar problems in other
machining applications. The developed framework can serve as guidance for researchers to obtain multivariable
optimal setting in a systematic way.
Parametric Optimization of Wire Electrical Discharge Machining (WEDM) Process...theijes
The International Journal of Engineering & Science is aimed at providing a platform for researchers, engineers, scientists, or educators to publish their original research results, to exchange new ideas, to disseminate information in innovative designs, engineering experiences and technological skills. It is also the Journal's objective to promote engineering and technology education. All papers submitted to the Journal will be blind peer-reviewed. Only original articles will be published.
The papers for publication in The International Journal of Engineering& Science are selected through rigorous peer reviews to ensure originality, timeliness, relevance, and readability.
Theoretical work submitted to the Journal should be original in its motivation or modeling structure. Empirical analysis should be based on a theoretical framework and should be capable of replication. It is expected that all materials required for replication (including computer programs and data sets) should be available upon request to the authors.
The International Journal of Engineering & Science would take much care in making your article published without much delay with your kind cooperation
Development of a Taguchi-based framework for optimizing two quality character...IJERA Editor
A framework based on Taguchi parameter design was developed and successfully demonstrated to optimize two
quality characteristics- surface roughness and angular accuracy in Wire Electrical Discharge Machining (WEDM)
process. An orthogonal array (OA)L9was used in the Taguchi experiment design for four controllable
factors, each with three levels. With one non-controllable factor investigated, 18 experiments were conducted in
the Taguchi-based experiment setting, compared to 3
4
(=81) parameter combination as required by a traditional
DOE setting. Conducted for the two response variables, Taguchi experiments from the case study gave the
optimal combination of pulse on time at 9µs (A1), feed rate at 35 in/min (B2), voltage at 8v (C2), and wire
tension at 165g (D3) for surface roughness optmization, and pulse on time at 13µs (A3), feed rate at 35 in/min
(B2), voltage at 8v (C2), and wire tension at 160g (D2) for angular accuracy optmization. This optimal parameter
setting combination was verified through a confirmation run that confirms the optimal quality responses of
126.1µin for surface roughness and 0.024º for angular accuracy. This research ultimately showed the dual
output variable improvement and the framework established itself as a means to solve similar problems in other
machining applications. The developed framework can serve as guidance for researchers to obtain multivariable
optimal setting in a systematic way.
Development of a Taguchi-based framework for optimizing two quality character...IJERA Editor
A framework based on Taguchi parameter design was developed and successfully demonstrated to optimize two
quality characteristics- surface roughness and angular accuracy in Wire Electrical Discharge Machining (WEDM)
process. An orthogonal array (OA)L9was used in the Taguchi experiment design for four controllable
factors, each with three levels. With one non-controllable factor investigated, 18 experiments were conducted in
the Taguchi-based experiment setting, compared to 34 (=81) parameter combination as required by a traditional
DOE setting. Conducted for the two response variables, Taguchi experiments from the case study gave the
optimal combination of pulse on time at 9μs (A1), feed rate at 35 in/min (B2), voltage at 8v (C2), and wire
tension at 165g (D3) for surface roughness optmization, and pulse on time at 13μs (A3), feed rate at 35 in/min
(B2), voltage at 8v (C2), and wire tension at 160g (D2) for angular accuracy optmization. This optimal parameter
setting combination was verified through a confirmation run that confirms the optimal quality responses of
126.1μin for surface roughness and 0.024º for angular accuracy. This research ultimately showed the dual
output variable improvement and the framework established itself as a means to solve similar problems in other
machining applications. The developed framework can serve as guidance for researchers to obtain multivariable
optimal setting in a systematic way.
Parametric Optimization of Wire Electrical Discharge Machining (WEDM) Process...theijes
The International Journal of Engineering & Science is aimed at providing a platform for researchers, engineers, scientists, or educators to publish their original research results, to exchange new ideas, to disseminate information in innovative designs, engineering experiences and technological skills. It is also the Journal's objective to promote engineering and technology education. All papers submitted to the Journal will be blind peer-reviewed. Only original articles will be published.
The papers for publication in The International Journal of Engineering& Science are selected through rigorous peer reviews to ensure originality, timeliness, relevance, and readability.
Theoretical work submitted to the Journal should be original in its motivation or modeling structure. Empirical analysis should be based on a theoretical framework and should be capable of replication. It is expected that all materials required for replication (including computer programs and data sets) should be available upon request to the authors.
The International Journal of Engineering & Science would take much care in making your article published without much delay with your kind cooperation
Optimization of Cutting Rate for EN 1010 Low Alloy Steel on WEDM Using Respon...IJAEMSJORNAL
EN 1010is a low-carbon steel alloy with 0.10% carbon content. It is known for its fairly low strength and low ductility; however, it can be tempered to increase strength. Machinability of EN 1010 carbon steel is measured to be fairly good. EN 1010 is commonly used for cold headed fasteners, rivets and bolts, in addition to structural, construction and automotive applications such as fenders, pans, nails and transmission covers. Wire Electric Discharge Machine (WEDM) seems to be a good option for machining the complicated profiles. This paper, find effects of various process parameters of Wire EDM such as pulse on time (Ton), pulse off time(Toff), peak current (Ip) and servo voltage (Sv) for analysis of cutting rate (CR) while machining EN 1010. Central Composite Design is used to plan the design of experiment. The output response variable being cutting rate will be measured for all number of experiments conducted. The optimal parameter level combination would be analysed which gives desired cutting rate. These optimized values of different parameters would then be used in execution the machining operation in order to obtain the necessary outputs.
Optimization of WEDM Process Parameters on Titanium Alloy Using Taguchi MethodIJMER
International Journal of Modern Engineering Research (IJMER) is Peer reviewed, online Journal. It serves as an international archival forum of scholarly research related to engineering and science education.
International Journal of Modern Engineering Research (IJMER) covers all the fields of engineering and science: Electrical Engineering, Mechanical Engineering, Civil Engineering, Chemical Engineering, Computer Engineering, Agricultural Engineering, Aerospace Engineering, Thermodynamics, Structural Engineering, Control Engineering, Robotics, Mechatronics, Fluid Mechanics, Nanotechnology, Simulators, Web-based Learning, Remote Laboratories, Engineering Design Methods, Education Research, Students' Satisfaction and Motivation, Global Projects, and Assessment…. And many more.
Process Parameter Optimization of WEDM for AISI M2 & AISI H13 by Anova & Anal...IJERA Editor
WEDM is a widely recognized unconventional material cutting process used to manufacture components with complex shapes and profiles of hard materials. In this thermal erosion process, there is no physical contact between the wire tool and work materials. AISI M2 and AISI H13 materials are taken for studyand molybdenum wire electrode diameter (0.18mm); experiment is conducted according to Taguchi‟s L16 OA, with input parameters as Peak current, Pulse on, Pulse off their response on MRR, Surface Roughness, Kerf width & Spark Gap is analysed to check the significance of each using ANOVA. Process parameter optimization is done by Analytic Hierarchy Process with the criteria Maximum MRR, minimum kerf and surface roughness. It is observed that for material AISI M2 at low value of peak current (1 A), pulse off (20μs) and pulse on (30μs) we can minimize surface roughness (3.30μm), kerf width (0.195 mm) and maximize MRR (0.022 g/min),from the selected levels whereas for material AISI H13 Peak current (1A), Pulse On (40μs) and high Pulse Off (30μs) we get better Surface roughness (3.71 μm), kerf width (0.196mm) and maximum MRR (0.020g/min), from the selected levels.
Optimization of Surface Roughness for EN 1010 Low Alloy Steel on WEDM Using R...IJAEMSJORNAL
The term steel is used for many different alloys of iron. All steels cover small amounts of carbon and manganese. There do exist many types of steels which are(among others) plain carbon steel, stainless steel, alloysteel and tool steel. Carbon steel is the most extensively used kind of steel. The properties of carbon steel depend mainly on the amount of carbon it contains. Maximum carbon steel has a carbon content of less than 1%. Carbon steel is made into an extensive range of products, including structural beams, car bodies. In fact, there are 3 types of plain carbon steel namely low carbon steel, medium carbon steel, high carbon steel. It is good to exact that plain carbon steel is a type of steel having a maximum carbon content of 1.5% along with small percentages of silica, Sulphur, phosphorus and manganese. EN 1010 is a lowest amount of carbonalloy steel alloy with carbon content of 0.10%. Machineability of EN 1010 carbon steel is measured to be fairly good. EN 1010 is usually used for rivets and bolts, construction and automotive applications such as pans, nails and transmission cover. The objective of paper is to study the effect of process parameters namely pulse on time, pulse off time, peak current and servo voltage on surface roughness(SR).The effect of process parameters on productivity and accuracy facts is material dependent. To study parametric effect on Surface Roughness a Central Composite design approach of response surface methodology (RSM) is used to plan and study the experiments. The mathematical relationships between WEDM input process parameters and response parameter namely surface roughness is established to determine optimal values of surface roughness mathematically and graphically.The Analysis of variance (ANOVA) is performed to find statistically significant process parameters. Interaction effects of process parameters on surface roughness are analysed using statistical and graphical representations.
Modeling of wedm process for complex shape using multilayer perceptron and re...eSAT Journals
Abstract
Wire cut electric discharge machining is the present days requirement in manufacturing the intricate and complex shape parts as required in the modern industrial products. The process being complex in nature for control over the machining process parameters. In the present study Multilayer perceptron (MLP) model is developed to predict the Material removal rate. The mathematical regression model is also developed by using Response Surface Methodology (RSM) to establish the relationshIp between the MRR and input process parameters like pulse on time (Ton), Pulse off time (Toff), Peak current (IP) and Servo voltage (SV). The predicted value by using MLP and RSM were compared with the experimental values. The average percentage errors are found to be 1.29 and -0.36527 for MLP and RSM respectively. It is observed that the predicted values with RSM are closer to experimental values as compared to MLP model. Key Words: WEDM, Response Surface Methodology, Neural Network, Multi Layer Perception, Material Removal Rate, Surface Roughness
Investigation on Optimization of Machining Parameters in Wire EDM using Taguc...ijsrd.com
In this paper, the parameters used in the cutting of Cemented Tungsten Carbide using wire electrical discharge machining (WEDM) with a Brass electrode was optimized using Taguchi method. Taguchi method is used to formulate the experimental layout and to analyze the effect of each parameter on the machining characteristics. Also it is used to predict the optimal choice for each parameter such as peak current, voltage, and pulse duration and interval time. It was found that these parameters have significant influence on machining characteristics such as Metal Removal Rate (MRR) and Surface Roughness (SR). The result of the work reveals that, the peak current significantly affects the Surface Roughness (SR) and the pulse duration mainly affects the Metal Removal Rate (MRR).
Optimization of EDM Process of (Cu-W) EDM Electrodes on Different ProgressionIJERA Editor
The purpose of this research work is to determine the optimal cutting condition of EDM process of different
work piece materials using different compositions of Cu-W tool Electrodes. The key cutting factors such as
Discharge Current, Voltage, Pulse- On – Time, Duty Cycle, Spark Gap and flushing pressure will be optimized.
Effect Of Wire Edm Process Parameters On Surface Roughness Of Aisi-4140 (Carb...dbpublications
WEDM is used for cutting intricate or complicated shapes which are not possible with conventional machining methods. Wire cut EDM is a cutting process used widely where conventional machining processes are not useful. A metal wire with a Dielectric medium travels through a path and perform machining procedure .The main objective of the present work is to investigate the effects of various WEDM process parameters on the machining quality and to obtain the optimal sets of process parameters like Pulse-ON time, Pulse-OFF time, current, wire feed are studied by conducting an experiment. Taguchi Method is to design the experiment. L16 orthogonal array is used to conduct the experiment. An AISI-4140 (carbon steel) is used as a work piece material in the form of square bar. The surface roughness (SR) is selected as response variable.
ELECTRO CHEMICAL MACHINING AND ELECTRICAL DISCHARGE MACHINING PROCESSES MICRO...ijiert bestjournal
Nowadays,necessity of small components is a common trend. These requirements encourage the researcher s to develop very minutest size components to fulfill the demand. The manufact uring of these type of components is a difficult ob ligation and for that various machining methods are develop to manufacture such c omponents. In this article the Electro Chemical mac hining and Electrical Discharge Machining is reviewed. We tried to summar ize the work of various researchers. The study show s that this type of machining processes gives good alternative.
Similar to Optimization of Process Parameters of Powder Mixed Wire-cut Electric Discharge Machining on NIMONIC 90 Using Taguchi Method and Grey Relational Analysis
Optimization of Cutting Rate for EN 1010 Low Alloy Steel on WEDM Using Respon...IJAEMSJORNAL
EN 1010is a low-carbon steel alloy with 0.10% carbon content. It is known for its fairly low strength and low ductility; however, it can be tempered to increase strength. Machinability of EN 1010 carbon steel is measured to be fairly good. EN 1010 is commonly used for cold headed fasteners, rivets and bolts, in addition to structural, construction and automotive applications such as fenders, pans, nails and transmission covers. Wire Electric Discharge Machine (WEDM) seems to be a good option for machining the complicated profiles. This paper, find effects of various process parameters of Wire EDM such as pulse on time (Ton), pulse off time(Toff), peak current (Ip) and servo voltage (Sv) for analysis of cutting rate (CR) while machining EN 1010. Central Composite Design is used to plan the design of experiment. The output response variable being cutting rate will be measured for all number of experiments conducted. The optimal parameter level combination would be analysed which gives desired cutting rate. These optimized values of different parameters would then be used in execution the machining operation in order to obtain the necessary outputs.
Optimization of WEDM Process Parameters on Titanium Alloy Using Taguchi MethodIJMER
International Journal of Modern Engineering Research (IJMER) is Peer reviewed, online Journal. It serves as an international archival forum of scholarly research related to engineering and science education.
International Journal of Modern Engineering Research (IJMER) covers all the fields of engineering and science: Electrical Engineering, Mechanical Engineering, Civil Engineering, Chemical Engineering, Computer Engineering, Agricultural Engineering, Aerospace Engineering, Thermodynamics, Structural Engineering, Control Engineering, Robotics, Mechatronics, Fluid Mechanics, Nanotechnology, Simulators, Web-based Learning, Remote Laboratories, Engineering Design Methods, Education Research, Students' Satisfaction and Motivation, Global Projects, and Assessment…. And many more.
Process Parameter Optimization of WEDM for AISI M2 & AISI H13 by Anova & Anal...IJERA Editor
WEDM is a widely recognized unconventional material cutting process used to manufacture components with complex shapes and profiles of hard materials. In this thermal erosion process, there is no physical contact between the wire tool and work materials. AISI M2 and AISI H13 materials are taken for studyand molybdenum wire electrode diameter (0.18mm); experiment is conducted according to Taguchi‟s L16 OA, with input parameters as Peak current, Pulse on, Pulse off their response on MRR, Surface Roughness, Kerf width & Spark Gap is analysed to check the significance of each using ANOVA. Process parameter optimization is done by Analytic Hierarchy Process with the criteria Maximum MRR, minimum kerf and surface roughness. It is observed that for material AISI M2 at low value of peak current (1 A), pulse off (20μs) and pulse on (30μs) we can minimize surface roughness (3.30μm), kerf width (0.195 mm) and maximize MRR (0.022 g/min),from the selected levels whereas for material AISI H13 Peak current (1A), Pulse On (40μs) and high Pulse Off (30μs) we get better Surface roughness (3.71 μm), kerf width (0.196mm) and maximum MRR (0.020g/min), from the selected levels.
Optimization of Surface Roughness for EN 1010 Low Alloy Steel on WEDM Using R...IJAEMSJORNAL
The term steel is used for many different alloys of iron. All steels cover small amounts of carbon and manganese. There do exist many types of steels which are(among others) plain carbon steel, stainless steel, alloysteel and tool steel. Carbon steel is the most extensively used kind of steel. The properties of carbon steel depend mainly on the amount of carbon it contains. Maximum carbon steel has a carbon content of less than 1%. Carbon steel is made into an extensive range of products, including structural beams, car bodies. In fact, there are 3 types of plain carbon steel namely low carbon steel, medium carbon steel, high carbon steel. It is good to exact that plain carbon steel is a type of steel having a maximum carbon content of 1.5% along with small percentages of silica, Sulphur, phosphorus and manganese. EN 1010 is a lowest amount of carbonalloy steel alloy with carbon content of 0.10%. Machineability of EN 1010 carbon steel is measured to be fairly good. EN 1010 is usually used for rivets and bolts, construction and automotive applications such as pans, nails and transmission cover. The objective of paper is to study the effect of process parameters namely pulse on time, pulse off time, peak current and servo voltage on surface roughness(SR).The effect of process parameters on productivity and accuracy facts is material dependent. To study parametric effect on Surface Roughness a Central Composite design approach of response surface methodology (RSM) is used to plan and study the experiments. The mathematical relationships between WEDM input process parameters and response parameter namely surface roughness is established to determine optimal values of surface roughness mathematically and graphically.The Analysis of variance (ANOVA) is performed to find statistically significant process parameters. Interaction effects of process parameters on surface roughness are analysed using statistical and graphical representations.
Modeling of wedm process for complex shape using multilayer perceptron and re...eSAT Journals
Abstract
Wire cut electric discharge machining is the present days requirement in manufacturing the intricate and complex shape parts as required in the modern industrial products. The process being complex in nature for control over the machining process parameters. In the present study Multilayer perceptron (MLP) model is developed to predict the Material removal rate. The mathematical regression model is also developed by using Response Surface Methodology (RSM) to establish the relationshIp between the MRR and input process parameters like pulse on time (Ton), Pulse off time (Toff), Peak current (IP) and Servo voltage (SV). The predicted value by using MLP and RSM were compared with the experimental values. The average percentage errors are found to be 1.29 and -0.36527 for MLP and RSM respectively. It is observed that the predicted values with RSM are closer to experimental values as compared to MLP model. Key Words: WEDM, Response Surface Methodology, Neural Network, Multi Layer Perception, Material Removal Rate, Surface Roughness
Investigation on Optimization of Machining Parameters in Wire EDM using Taguc...ijsrd.com
In this paper, the parameters used in the cutting of Cemented Tungsten Carbide using wire electrical discharge machining (WEDM) with a Brass electrode was optimized using Taguchi method. Taguchi method is used to formulate the experimental layout and to analyze the effect of each parameter on the machining characteristics. Also it is used to predict the optimal choice for each parameter such as peak current, voltage, and pulse duration and interval time. It was found that these parameters have significant influence on machining characteristics such as Metal Removal Rate (MRR) and Surface Roughness (SR). The result of the work reveals that, the peak current significantly affects the Surface Roughness (SR) and the pulse duration mainly affects the Metal Removal Rate (MRR).
Optimization of EDM Process of (Cu-W) EDM Electrodes on Different ProgressionIJERA Editor
The purpose of this research work is to determine the optimal cutting condition of EDM process of different
work piece materials using different compositions of Cu-W tool Electrodes. The key cutting factors such as
Discharge Current, Voltage, Pulse- On – Time, Duty Cycle, Spark Gap and flushing pressure will be optimized.
Effect Of Wire Edm Process Parameters On Surface Roughness Of Aisi-4140 (Carb...dbpublications
WEDM is used for cutting intricate or complicated shapes which are not possible with conventional machining methods. Wire cut EDM is a cutting process used widely where conventional machining processes are not useful. A metal wire with a Dielectric medium travels through a path and perform machining procedure .The main objective of the present work is to investigate the effects of various WEDM process parameters on the machining quality and to obtain the optimal sets of process parameters like Pulse-ON time, Pulse-OFF time, current, wire feed are studied by conducting an experiment. Taguchi Method is to design the experiment. L16 orthogonal array is used to conduct the experiment. An AISI-4140 (carbon steel) is used as a work piece material in the form of square bar. The surface roughness (SR) is selected as response variable.
ELECTRO CHEMICAL MACHINING AND ELECTRICAL DISCHARGE MACHINING PROCESSES MICRO...ijiert bestjournal
Nowadays,necessity of small components is a common trend. These requirements encourage the researcher s to develop very minutest size components to fulfill the demand. The manufact uring of these type of components is a difficult ob ligation and for that various machining methods are develop to manufacture such c omponents. In this article the Electro Chemical mac hining and Electrical Discharge Machining is reviewed. We tried to summar ize the work of various researchers. The study show s that this type of machining processes gives good alternative.
Similar to Optimization of Process Parameters of Powder Mixed Wire-cut Electric Discharge Machining on NIMONIC 90 Using Taguchi Method and Grey Relational Analysis (20)
Welcome to WIPAC Monthly the magazine brought to you by the LinkedIn Group Water Industry Process Automation & Control.
In this month's edition, along with this month's industry news to celebrate the 13 years since the group was created we have articles including
A case study of the used of Advanced Process Control at the Wastewater Treatment works at Lleida in Spain
A look back on an article on smart wastewater networks in order to see how the industry has measured up in the interim around the adoption of Digital Transformation in the Water Industry.
Student information management system project report ii.pdfKamal Acharya
Our project explains about the student management. This project mainly explains the various actions related to student details. This project shows some ease in adding, editing and deleting the student details. It also provides a less time consuming process for viewing, adding, editing and deleting the marks of the students.
Final project report on grocery store management system..pdfKamal Acharya
In today’s fast-changing business environment, it’s extremely important to be able to respond to client needs in the most effective and timely manner. If your customers wish to see your business online and have instant access to your products or services.
Online Grocery Store is an e-commerce website, which retails various grocery products. This project allows viewing various products available enables registered users to purchase desired products instantly using Paytm, UPI payment processor (Instant Pay) and also can place order by using Cash on Delivery (Pay Later) option. This project provides an easy access to Administrators and Managers to view orders placed using Pay Later and Instant Pay options.
In order to develop an e-commerce website, a number of Technologies must be studied and understood. These include multi-tiered architecture, server and client-side scripting techniques, implementation technologies, programming language (such as PHP, HTML, CSS, JavaScript) and MySQL relational databases. This is a project with the objective to develop a basic website where a consumer is provided with a shopping cart website and also to know about the technologies used to develop such a website.
This document will discuss each of the underlying technologies to create and implement an e- commerce website.
Courier management system project report.pdfKamal Acharya
It is now-a-days very important for the people to send or receive articles like imported furniture, electronic items, gifts, business goods and the like. People depend vastly on different transport systems which mostly use the manual way of receiving and delivering the articles. There is no way to track the articles till they are received and there is no way to let the customer know what happened in transit, once he booked some articles. In such a situation, we need a system which completely computerizes the cargo activities including time to time tracking of the articles sent. This need is fulfilled by Courier Management System software which is online software for the cargo management people that enables them to receive the goods from a source and send them to a required destination and track their status from time to time.
About
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.
Technical Specifications
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
Key Features
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface
• Compatible with MAFI CCR system
• Copatiable with IDM8000 CCR
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
Application
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.
Event Management System Vb Net Project Report.pdfKamal Acharya
In present era, the scopes of information technology growing with a very fast .We do not see any are untouched from this industry. The scope of information technology has become wider includes: Business and industry. Household Business, Communication, Education, Entertainment, Science, Medicine, Engineering, Distance Learning, Weather Forecasting. Carrier Searching and so on.
My project named “Event Management System” is software that store and maintained all events coordinated in college. It also helpful to print related reports. My project will help to record the events coordinated by faculties with their Name, Event subject, date & details in an efficient & effective ways.
In my system we have to make a system by which a user can record all events coordinated by a particular faculty. In our proposed system some more featured are added which differs it from the existing system such as security.
Sachpazis:Terzaghi Bearing Capacity Estimation in simple terms with Calculati...Dr.Costas Sachpazis
Terzaghi's soil bearing capacity theory, developed by Karl Terzaghi, is a fundamental principle in geotechnical engineering used to determine the bearing capacity of shallow foundations. This theory provides a method to calculate the ultimate bearing capacity of soil, which is the maximum load per unit area that the soil can support without undergoing shear failure. The Calculation HTML Code included.
Forklift Classes Overview by Intella PartsIntella Parts
Discover the different forklift classes and their specific applications. Learn how to choose the right forklift for your needs to ensure safety, efficiency, and compliance in your operations.
For more technical information, visit our website https://intellaparts.com
TECHNICAL TRAINING MANUAL GENERAL FAMILIARIZATION COURSEDuvanRamosGarzon1
AIRCRAFT GENERAL
The Single Aisle is the most advanced family aircraft in service today, with fly-by-wire flight controls.
The A318, A319, A320 and A321 are twin-engine subsonic medium range aircraft.
The family offers a choice of engines
Optimization of Process Parameters of Powder Mixed Wire-cut Electric Discharge Machining on NIMONIC 90 Using Taguchi Method and Grey Relational Analysis