This document provides an overview of optical satellite communications, including intersatellite links (ISLs) and global achievements. It discusses how ISLs allow for increased capacity and coverage by connecting satellites in different orbits, such as GEO-LEO and GEO-GEO links. Optical communications provide advantages over radio links, including higher antenna gains due to shorter wavelengths, but require more accurate pointing and tracking. The document outlines examples of optical ISL applications and global satellite networks using interconnected satellites.
this presentation is about satellite communication which includes working of gps ,vsat ,frequency bands ,needs of communication satellite ,types of satellite ,working ,orbits ,elements involved in working ,transponder ,satellite control center ,satellite network
this presentation is about satellite communication which includes working of gps ,vsat ,frequency bands ,needs of communication satellite ,types of satellite ,working ,orbits ,elements involved in working ,transponder ,satellite control center ,satellite network
Here is the 2nd project of mine, given by college students. get information from this. want to create like this contact me @instagram slide+ presentation
Free Space Optics (FSO) communications, also called Free Space Photonics (FSP) or Optical Wireless, refers to the transmission of modulated visible or infrared (IR) beams through the atmosphere to obtain optical communications. Like fiber, Free Space Optics (FSO) uses lasers to transmit data, but instead of enclosing the data stream in a glass fiber, it is transmitted through the air. Free Space Optics (FSO) works on the same basic principle as Infrared television remote controls, wireless keyboards
Free-space optical communication is an optical communication technology that uses light propagating in free space to wirelessly transmit data for telecommunications or computer networking. It is a technology that can be installed license-free worldwide and can be installed in less than a day. A technology that offers a fast, high ROI. There is no Frequency License Required in it.
This presentation covers:
Basics of Satellite communication
Indian Communication satellites
Satellite link and elements of satellite communication
Frequency bands of satellite communication
Different orbits of satellite communication
Link budget calculations
it's gives the full description about satellite . it's provide the knowledge about wireless communication.and it's gives the comparison between oft and satellite.ti's gives the basic knowledge about optical fibre
Here is the 2nd project of mine, given by college students. get information from this. want to create like this contact me @instagram slide+ presentation
Free Space Optics (FSO) communications, also called Free Space Photonics (FSP) or Optical Wireless, refers to the transmission of modulated visible or infrared (IR) beams through the atmosphere to obtain optical communications. Like fiber, Free Space Optics (FSO) uses lasers to transmit data, but instead of enclosing the data stream in a glass fiber, it is transmitted through the air. Free Space Optics (FSO) works on the same basic principle as Infrared television remote controls, wireless keyboards
Free-space optical communication is an optical communication technology that uses light propagating in free space to wirelessly transmit data for telecommunications or computer networking. It is a technology that can be installed license-free worldwide and can be installed in less than a day. A technology that offers a fast, high ROI. There is no Frequency License Required in it.
This presentation covers:
Basics of Satellite communication
Indian Communication satellites
Satellite link and elements of satellite communication
Frequency bands of satellite communication
Different orbits of satellite communication
Link budget calculations
it's gives the full description about satellite . it's provide the knowledge about wireless communication.and it's gives the comparison between oft and satellite.ti's gives the basic knowledge about optical fibre
Laser communications offer a viable alternative to RF communications for inter satellite links and other applications where high-performance links are a necessity.
Drones are a different kind of new technology from what we’re used to. They offer something else: the conquest of physical space, the extension of society’s compass, the ability to be anywhere and see anything.
For the past few years, one of the most exciting class of gadgets on display has been drones. They got cheaper, lighter, and easier to use even as they became more powerful.
We believe 2015 is an important year for drones as they will change how brands interact with consumers in both advertising and events, and here's everything you need to know about the drone technology.
An unmanned aerial vehicle (UAV), commonly known as a Drone, is an aircraft without a human pilot on board. UAVs can be remote controlled aircraft (e.g. flown by a pilot at a ground control station) or can fly autonomously based on pre-programmed flight plans or more complex dynamic automation systems
A UAV is defined as being capable of controlled, sustained level flight and powered by a jet or reciprocating engine. In addition, a cruise missile can be considered to be a UAV, but is treated separately on the basis that the vehicle is the weapon.
Unmanned Aerial Vehicles (UAVs) are aircrafts that fly without any humans being onboard. They are either remotely piloted, or piloted by an onboard computer. This kind of aircrafts can be used in different military missions such as surveillance, reconnaissance, battle damage assessment, communications relay, minesweeping, hazardous substances detection and radar jamming. However they can be used in other than military missions like detection of hazardous objects on train rails and investigation of infected areas. Aircrafts that are able of hovering and vertical flying can also be used for indoor missions like counter terrorist operations
To download this ppt click on this link
https://adf.ly/PdL4V
This report gives the viewers a broad description about using a light wave generated from a typical LED's or LASER source for an effective communication.
A satellite system is a set of gravitationally bound objects in orbit around a planetary-mass object or minor planet, or its barycenter. Generally speaking, it is a set of natural satellites (moons), although such systems may also consist of bodies such as circumplanetary disks, ring systems, moonlets, minor-planet moons, and artificial satellites any which may themselves have satellite systems of their own.
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology
Satellite Internet is the ability to transmit and receive data from a relatively small satellite dish on Earth and communicate with an orbiting geostationary satellite 22,300 miles above Earth's equator.
LEO
MEO
GEO
UiPath Test Automation using UiPath Test Suite series, part 3DianaGray10
Welcome to UiPath Test Automation using UiPath Test Suite series part 3. In this session, we will cover desktop automation along with UI automation.
Topics covered:
UI automation Introduction,
UI automation Sample
Desktop automation flow
Pradeep Chinnala, Senior Consultant Automation Developer @WonderBotz and UiPath MVP
Deepak Rai, Automation Practice Lead, Boundaryless Group and UiPath MVP
DevOps and Testing slides at DASA ConnectKari Kakkonen
My and Rik Marselis slides at 30.5.2024 DASA Connect conference. We discuss about what is testing, then what is agile testing and finally what is Testing in DevOps. Finally we had lovely workshop with the participants trying to find out different ways to think about quality and testing in different parts of the DevOps infinity loop.
JMeter webinar - integration with InfluxDB and GrafanaRTTS
Watch this recorded webinar about real-time monitoring of application performance. See how to integrate Apache JMeter, the open-source leader in performance testing, with InfluxDB, the open-source time-series database, and Grafana, the open-source analytics and visualization application.
In this webinar, we will review the benefits of leveraging InfluxDB and Grafana when executing load tests and demonstrate how these tools are used to visualize performance metrics.
Length: 30 minutes
Session Overview
-------------------------------------------
During this webinar, we will cover the following topics while demonstrating the integrations of JMeter, InfluxDB and Grafana:
- What out-of-the-box solutions are available for real-time monitoring JMeter tests?
- What are the benefits of integrating InfluxDB and Grafana into the load testing stack?
- Which features are provided by Grafana?
- Demonstration of InfluxDB and Grafana using a practice web application
To view the webinar recording, go to:
https://www.rttsweb.com/jmeter-integration-webinar
Search and Society: Reimagining Information Access for Radical FuturesBhaskar Mitra
The field of Information retrieval (IR) is currently undergoing a transformative shift, at least partly due to the emerging applications of generative AI to information access. In this talk, we will deliberate on the sociotechnical implications of generative AI for information access. We will argue that there is both a critical necessity and an exciting opportunity for the IR community to re-center our research agendas on societal needs while dismantling the artificial separation between the work on fairness, accountability, transparency, and ethics in IR and the rest of IR research. Instead of adopting a reactionary strategy of trying to mitigate potential social harms from emerging technologies, the community should aim to proactively set the research agenda for the kinds of systems we should build inspired by diverse explicitly stated sociotechnical imaginaries. The sociotechnical imaginaries that underpin the design and development of information access technologies needs to be explicitly articulated, and we need to develop theories of change in context of these diverse perspectives. Our guiding future imaginaries must be informed by other academic fields, such as democratic theory and critical theory, and should be co-developed with social science scholars, legal scholars, civil rights and social justice activists, and artists, among others.
"Impact of front-end architecture on development cost", Viktor TurskyiFwdays
I have heard many times that architecture is not important for the front-end. Also, many times I have seen how developers implement features on the front-end just following the standard rules for a framework and think that this is enough to successfully launch the project, and then the project fails. How to prevent this and what approach to choose? I have launched dozens of complex projects and during the talk we will analyze which approaches have worked for me and which have not.
Builder.ai Founder Sachin Dev Duggal's Strategic Approach to Create an Innova...Ramesh Iyer
In today's fast-changing business world, Companies that adapt and embrace new ideas often need help to keep up with the competition. However, fostering a culture of innovation takes much work. It takes vision, leadership and willingness to take risks in the right proportion. Sachin Dev Duggal, co-founder of Builder.ai, has perfected the art of this balance, creating a company culture where creativity and growth are nurtured at each stage.
GraphRAG is All You need? LLM & Knowledge GraphGuy Korland
Guy Korland, CEO and Co-founder of FalkorDB, will review two articles on the integration of language models with knowledge graphs.
1. Unifying Large Language Models and Knowledge Graphs: A Roadmap.
https://arxiv.org/abs/2306.08302
2. Microsoft Research's GraphRAG paper and a review paper on various uses of knowledge graphs:
https://www.microsoft.com/en-us/research/blog/graphrag-unlocking-llm-discovery-on-narrative-private-data/
Kubernetes & AI - Beauty and the Beast !?! @KCD Istanbul 2024Tobias Schneck
As AI technology is pushing into IT I was wondering myself, as an “infrastructure container kubernetes guy”, how get this fancy AI technology get managed from an infrastructure operational view? Is it possible to apply our lovely cloud native principals as well? What benefit’s both technologies could bring to each other?
Let me take this questions and provide you a short journey through existing deployment models and use cases for AI software. On practical examples, we discuss what cloud/on-premise strategy we may need for applying it to our own infrastructure to get it to work from an enterprise perspective. I want to give an overview about infrastructure requirements and technologies, what could be beneficial or limiting your AI use cases in an enterprise environment. An interactive Demo will give you some insides, what approaches I got already working for real.
Key Trends Shaping the Future of Infrastructure.pdfCheryl Hung
Keynote at DIGIT West Expo, Glasgow on 29 May 2024.
Cheryl Hung, ochery.com
Sr Director, Infrastructure Ecosystem, Arm.
The key trends across hardware, cloud and open-source; exploring how these areas are likely to mature and develop over the short and long-term, and then considering how organisations can position themselves to adapt and thrive.
Slack (or Teams) Automation for Bonterra Impact Management (fka Social Soluti...Jeffrey Haguewood
Sidekick Solutions uses Bonterra Impact Management (fka Social Solutions Apricot) and automation solutions to integrate data for business workflows.
We believe integration and automation are essential to user experience and the promise of efficient work through technology. Automation is the critical ingredient to realizing that full vision. We develop integration products and services for Bonterra Case Management software to support the deployment of automations for a variety of use cases.
This video focuses on the notifications, alerts, and approval requests using Slack for Bonterra Impact Management. The solutions covered in this webinar can also be deployed for Microsoft Teams.
Interested in deploying notification automations for Bonterra Impact Management? Contact us at sales@sidekicksolutionsllc.com to discuss next steps.
Software Delivery At the Speed of AI: Inflectra Invests In AI-Powered QualityInflectra
In this insightful webinar, Inflectra explores how artificial intelligence (AI) is transforming software development and testing. Discover how AI-powered tools are revolutionizing every stage of the software development lifecycle (SDLC), from design and prototyping to testing, deployment, and monitoring.
Learn about:
• The Future of Testing: How AI is shifting testing towards verification, analysis, and higher-level skills, while reducing repetitive tasks.
• Test Automation: How AI-powered test case generation, optimization, and self-healing tests are making testing more efficient and effective.
• Visual Testing: Explore the emerging capabilities of AI in visual testing and how it's set to revolutionize UI verification.
• Inflectra's AI Solutions: See demonstrations of Inflectra's cutting-edge AI tools like the ChatGPT plugin and Azure Open AI platform, designed to streamline your testing process.
Whether you're a developer, tester, or QA professional, this webinar will give you valuable insights into how AI is shaping the future of software delivery.
Neuro-symbolic is not enough, we need neuro-*semantic*Frank van Harmelen
Neuro-symbolic (NeSy) AI is on the rise. However, simply machine learning on just any symbolic structure is not sufficient to really harvest the gains of NeSy. These will only be gained when the symbolic structures have an actual semantics. I give an operational definition of semantics as “predictable inference”.
All of this illustrated with link prediction over knowledge graphs, but the argument is general.
GDG Cloud Southlake #33: Boule & Rebala: Effective AppSec in SDLC using Deplo...James Anderson
Effective Application Security in Software Delivery lifecycle using Deployment Firewall and DBOM
The modern software delivery process (or the CI/CD process) includes many tools, distributed teams, open-source code, and cloud platforms. Constant focus on speed to release software to market, along with the traditional slow and manual security checks has caused gaps in continuous security as an important piece in the software supply chain. Today organizations feel more susceptible to external and internal cyber threats due to the vast attack surface in their applications supply chain and the lack of end-to-end governance and risk management.
The software team must secure its software delivery process to avoid vulnerability and security breaches. This needs to be achieved with existing tool chains and without extensive rework of the delivery processes. This talk will present strategies and techniques for providing visibility into the true risk of the existing vulnerabilities, preventing the introduction of security issues in the software, resolving vulnerabilities in production environments quickly, and capturing the deployment bill of materials (DBOM).
Speakers:
Bob Boule
Robert Boule is a technology enthusiast with PASSION for technology and making things work along with a knack for helping others understand how things work. He comes with around 20 years of solution engineering experience in application security, software continuous delivery, and SaaS platforms. He is known for his dynamic presentations in CI/CD and application security integrated in software delivery lifecycle.
Gopinath Rebala
Gopinath Rebala is the CTO of OpsMx, where he has overall responsibility for the machine learning and data processing architectures for Secure Software Delivery. Gopi also has a strong connection with our customers, leading design and architecture for strategic implementations. Gopi is a frequent speaker and well-known leader in continuous delivery and integrating security into software delivery.
Let's dive deeper into the world of ODC! Ricardo Alves (OutSystems) will join us to tell all about the new Data Fabric. After that, Sezen de Bruijn (OutSystems) will get into the details on how to best design a sturdy architecture within ODC.
1. Optical Satellite Communications
Presented to: Prof. Dr. Hossam Shalaby
Presented by: Eng. Islam Mohamed Salah Kotb
Course: Laser and Electro-Optics ( EE-106381)
Faculty Of Engineering
Alexandria University
January 2009
2. Contents:
page
1.
2.
3.
4.
5.
Free Space Optical Communications…………………………………………
Intersatellite links……………………………………………………………...
Global Achievements…………………………………………………………
Optical Satellite Network – The future………………………………………..
References……………………………………………………………………...
2
3
4
15
21
29
3. Free Space Optical Communications:
Optical data transmission on Earth is in most cases done via optical fibers,
because these allow the transmission over relatively large distances without excessive
power losses, alignment issues, and disturbing influences of the atmosphere. However, it
is also possible to transmit data optically via free space, not exploiting any kind of
waveguide structure. This kind of optical communications has early origins, e.g. the
“photo phone” patent by Alexander Graham Bell in the 1870s and the optical telegraph
and is now increasingly used, both in space and on Earth. Generally, it requires an
unobstructed line of sight between sender and receiver, and normally also some special
free-space optics such as telescopes.
Space-based, free-space optical communications is a concept that has been around
for many years. In the last few years, however, there has been impressive activity to bring
the concept to fruition in civilian and government non-classified projects. Today's market
for space-based optical communications is primarily intersatellite links (ISLs) which are
the main focus of this study. There is also a place for high data rate (many Gbps) spaceearth links, though propagation effects due to the atmosphere and weather make this a
much more difficult link. Some activity in space-earth optical communications will also
be covered here.
One significant factor for Optical system is that the optical system will typically
have a much narrower beamwidth than the RF system. This has both a positive and
negative side. On the positive side, a narrower beamwidth means that the potential for
interference to or from adjacent satellites will be reduced. This is particularly important
in large LEO constellations. On the negative side, the requirements for more accurate
pointing, acquisition and tracking (PAT) and the impact that this may have on the
spacecraft could impose an unwelcome burden. Accurate PAT is critical to the
acceptance of optical ISLs.
A secondary, though not unimportant, fact about optical communications is that,
unlike the RF spectrum which is regulated by national and international agencies, the
optical spectrum is currently unregulated.
A third factor is the reliability of optical communications systems, particularly
their lasers, has been a concern in the past. This issue is being overcome by advances in
optical and laser technology but needs documented space validation for wider acceptance.
Finally, the basic advantage of the optical technology over radio links is that the
much shorter wavelength allows for a much more directional sending and receiving of
information. In technical terms, the antenna gain can be much higher. This is particularly
important for bridging interplanetary distances.
3
4. 2. Intersatellite Links (ISL):
Some space applications require large amount of data to be transferred. An
example is the transmission between different Earth-orbiting satellites (inter-satellite
communications), which was first demonstrated by ESA in 2001 (ESA). It is possible to
transmit tens of megabits per second or more over many thousands of kilometers, using
moderate laser average powers of the order of a few watts.
Space-Earth links have been, and continue to be, primarily RF. Because of the
advantages of optical systems related earlier, Japanese, European and U.S. researchers
are investigating optical space-earth links from LEO as well as the far reaches of outer
space. Optical links face a severe disadvantage due to the effects of the atmosphere and
weather. Solutions include adaptive optics, spatial diversity, and onboard storage with
burst transmission under good conditions. The first applications are likely to be in
scientific satellites but as operational methodologies are developed, space-earth optical
links will work their way into commercial systems.
Data can also be exchanged between a more remote spacecraft and a station on or
near Earth. For example, planetary probes can generate a lot of image data, and a major
challenge is to send large amount of data back to Earth. Until recently, radio links
operating e.g. in the X band or Ka band were the only available technology. Currently,
optical data links are considered particularly for the downlink, where the desired data
volumes are much larger than for the uplink, and optical communications could greatly
expand the transmission capacity to hundreds of kbit or even several megabits per
second. The spacecraft then has a pulsed laser source (employing pulse position
modulation, for example) and an optical telescope of moderate size targeting the receiver.
The latter can be a large ground-based telescope or a transceiver in an Earth orbit.
Intersatellite links can be considered as particular beams of multibeam satellites;
the beams in this case are directed not towards the earth but towards other satellites.
Three classes of intersatellite link can be distinguished:
•
•
•
Links (GEO-LEO) between geostationary earth orbit (GEO) and low earth orbit
(LEO) satellites; also called inter-orbital links (IOL).
Links between geostationary satellites (GEO-GEO).
Links between low orbit satellites (LEO-LEO).
2.1 Links between geostationary and low earth orbit satellites (GEOLEO):
This type of link serves to establish a permanent relay via a geostationary satellite
between one or more earth stations and a group of satellites proceeding in a low earth
orbit at an altitude of the order of 500 to 1000 km.
4
5. This concept is currently operated in the NASA tracking network by means of the
tracking and data relay satellites (TDRS). Also it is used by the European satellite
(ARTEMIS) which provides communications between the ground and low earth orbit
spacecraft.
2.2 Links between geostationary satellites (GEO-GEO):
There are many advantages for using (GEO-GEO) satellite links among which are
2.2.1 Increasing the capacity of a system:
If the traffic demand increases and exceeds the capacity of the satellite it is
therefore necessary to replace this satellite by another one with greater capacity which
faces many problems due to the cost and finding the suitable launcher. Instead of this we
use a second satellite identical to the first one and the intersatellite link carries the excess
traffic of region 1. (Figure 2.1)
Figure 2.1 Use of an intersatellite link to increase the capacity of a system without heavy investment in the
earth segment. (a)1 satellite network. (b) 2nd satellite is launched to increase the capacity of the system;
stations must be equipped with 2 antennas.. (c) With an ISL only stations of the most heavily loaded region
must be equipped with 2 antennas. (d) The stations are distributed between the 2 satellites. The ISL carries
the traffic between the 2 groups of stations.
5
6. 2.2.2 Extension of the coverage of a system:
An intersatellite link permits earth stations of 2 networks to be interconnected and
hence the geographical coverage of the 2 satellites to be combined. (Figure 2.2)
Figure 2.2 Extension of system coverage. (a) Interconnection of the stations of each coverage by a satellite
link. (b) Interconnection without an intersatellite link by a station common to the 2 networks. (c
Interconnection without an intersatellite link by a terrestrial network.
2.2.3 Increase of the minimum elevation angle of the earth stations:
Long distance link by a single satellite requires earth stations with a small
elevation angle which causes degradation of G/T for receiving station and increases risk
of interference with terrestrial microwave arrays. By using 2 interconnected satellites we
can use angles of about 20o. (Figure 2.3)
2.2.4 Reduction of the constraints on orbital position
The orbital position of a satellite is often the result of a conflict , resolved by
means of a procedure called co-ordination , between the desire of the satellite operator to
ensure coverage of the service are under the best conditions and he need to avoid
interference with established systems. Intersatellite links when they permit traffic to be
shared among several satellites in different orbital positions, provide the operator with
some latitude in the positioning of his satellite.
6
7. Figure 2.3 Increase of the minimum elevation angle of earth stations.
2.2.5 Satellite clusters
The principal is to locate several separate satellites in the same orbital position
with a separation of around 100 km and interconnection by intersatellite links. The
satellites are thus all in the main lobe of an earth station antenna and appear equivalent to
a single large capacity satellite.
2.2.6 A global network:
Figure 2.4 shows the design of a global network based on 9 geostationary STAR
satellites, which establish a basis for worldwide communication, and a set of local
satellites connected to these regional satellite links.
Figure 2.4 A Global Network
7
8. 2.3 Links between low orbit satellites (LEO-LEO):
The advantages of low orbit satellites and the increasing congestion of
geostationary satellite orbits suggest the future development of orbiting satellites.
In fact the disadvantages of an orbiting satellite (limited duration of communication time
and relatively small coverage) can be reduced in a network containing a large number of
satellites which are interconnected by intersatellite links and equipped with a means of
switching between beams. Motorola Inc. has planned to construct, launch and operate
such a network, called IRIDIUM, for worldwide cellular personal communication
services. The system incorporates a constellation of 66 satellites, designed initially with
77 satellites.
2.4 Frequency bands:
Table 2.1 indicates the frequency bands allocated to intersatellite links by the
Radiocommunication Regulations. These frequencies correspond to strong absorption
by the atmosphere and have been chosen to provide protection against interference
between intersatellite links and terrestrial systems.
Intersatellite service
Radio Frequency
Frequency Bands
22.55-23.55 GHz
24.45-24.75 GHz
32-33 GHz
54.25-58.2 GHz
0.8-0.9 µm (AIGaAs laser diode)
1.06 µm (Nd:YAG laser)
0.532 µm (Nd:YAG laser)
10.6 µm (CO2 laser)
Optical
Table 2.1Frequency bands for intersatellite links
2.5 Radio-frequency links:
Propagation losses reduce to free space losses since there is no passage through
the atmosphere. Antenna pointing error can be maintained at around a tenth of the
beamwidth and this leads to a pointing error loss of the order of 0.5 dB. For practical
applications antenna dimensions of the order of 1 to 2 m should be considered.
The development of high capacity RF intersatellite links between geostationary satellites
will imply re-use of frequencies from one beam to another. In view of the small angular
separation of the satellites, it would be preferable to use narrow beam antennas with
reduced side lobes in order to avoid interference between systems. Consequently, and in
view of the limited antenna size imposed by the launcher and the technical complexity of
the deployable antennas which may be deployed, the use of high frequencies is indicated.
The use of optical links may be usefully considered.
8
9. 2.6 Optical Links
2.6.1 Establishing a link:
Two aspects should be indicated: • The small diameter of the telescope which is typically of the order 0.3 m. In this
way one is freed from congestion problems and aperture blocking of other
antennas in the payload.
• The narrowness of the optical beam which is typically 5 microradians. Notice that
this width is several orders of magnitude less than that of a radio beam and this is
an advantage for protection against interference between systems. But it is also a
disadvantage since the beamwidth is much less than the precision of satellite
altitude control (typically 0.1 0 or 1.75 mrad). Consequently an advanced pointing
device is necessary; this is probably the most difficult technical problem.
There are three basic phases to optical communications:
• Acquisition: the beam must be a wide as possible in order to reduce the
acquisition time. But this requires a high power laser transmitter. A laser of lower
mean power can be used which emits pulses of high peak power with a low duty
cycle. The beam scans the region of space where the receiver receives the signal,
it enters a tracking phase and transmits in the direction of the received signal. On
receiving the return signal from the receiver, the transmitter also enters the
tracking phase. The typical duration of this phase is 10 seconds.
• Tracking: the beams are reduced to their nominal width. Laser transmission
becomes continuous. In this phase which extends throughout the following, the
pointing error control device must allow for movements of the platform and
relative movement of the two satellites. In addition, since the relative velocity pf
the 2 satellites is not zero, a lead-ahead angle exist between the receiver line of
sight and the transmitter line of sight. As will be demonstrated below, the Leadahead angle is larger than the beamwidth, and must be accurately determined.
• Communications: information is exchanged between the two ends.
2.6.2 Lead-ahead angle:
Consider two satellites, S1 and S2 respectively moving with velocity vectors VS1
VS2, whose components orthogonal to the line joining S1 and S2 at time t are
and
respectively the two vectors represented in figure 2.5 by VT1 and VT2.
The propagation time of a photon from S1 to S2 is tp=d/c, where d is the distance
between the two satellite at time t and c the speed of light (c=3 x 108 m/s).
The lead-ahead angle β is given by:
β =2
VT 1 − VT 2
C
Where |VT1-VT2| is the modulus of the difference vector VT1-VT2.
9
(2.1)
10. Figure 2.5 Lead-ahead angle for intersatellite between two satellites Sl and S2 with velocity vector
components VT1 and VT2 in a plane perpendicular to the line joining S1 and S2 at time t; tp is the
propagation time of a photon from S1 to S2.
Two situations will now be considered:
1. Intersatellite links between two geostationary satellites
2. Interorbital links between a geostationary satellite and a low earth orbiting
satellite.
2.6.2.1 Between two GEO satellite separated by angle α (Figure 2.6)
As both satellites are on the same circular orbit, the velocity vectors VS1 and VS2, which
are tangential to the orbit, have equal modulus, i.e.:
|VS1|=|VS2|=ω(RO+RE)=3075 m/s
Where:
ω is the angular velocity of a geostationary satellite =7.293x10-5 rad/ s
RO is the altitude of a geostationary satellite = 35786 km
RE is the earth radius = 6378 km
β =2
| VT 1 − VT 2 | 4ω ( RO + RE ) sin(α / 2)
=
C
C
(2.2)
10
11. Figure 2.6 Lead head angle for intersatellite links between 2 geostationary satellites
2.6.2.2 Between a GEO satellite and an LEO satellite with circular orbit ( Figure
2.7):
The relative velocity of the 2 satellites varies with time and so does the value of
the lead-ahead angle. Its maximum value is obtained when the LEO satellite crosses the
equatorial plane. Denoting as i the LEO satellite orbit inclination, then :
| VT 1 − VT 2 |= {| VS1 | 2 + | VS 2 | 2 −2 | VS 1 || VS 2 | cos i}1 / 2
(2.3)
Where
|VS1|= ωGEO(RO+RE)=3075 m/s
|VS2|= ωGEO(h+RE)
And h is the LEO satellite altitude, ωLEO+µ1/2(h+RE)-3/2 is the LEO satellite angular rate
(µ=3.986 x 1014 m3/s2)
From equation 2.1
2
C
β = ( ){|V S 1| 2 + |V S 2| 2 −2 |V S 1||V S 2| cos i}1 / 2 (rad)
11
(2.4)
12. Figure 2.7 Lead-ahead angle at a geostationary (GEO) satellite for interorbital links between it and a low
earth orbiting (LEO) satellite
2.6.3 Transmission:
Laser sources operate in single and multi-frequency modes. In single frequency
mode spectral width varies between 10 kHz and 10 MHz. In multi-frequency mode it is
from 1.5 to 10 nm. The power emitted depends on the type of laser. Table 2.2 gives
orders of magnitude.
Type of Laser
Solid state
AlGaAs
InPAaGa
ND:YAG
Nd:YAG
Gas Laser
CO2
Wavelength
Transmitted power
0.8-0.9 µm
1.3-1.5 µm
1.06 µm
0.532 µm
About 100 mW
About 100 mW
0.5-1 w
100 mW
10.6 µm
Several tens of watts
Table 2.2 Typical values of transmitted power for Lasers.
Modulation can be internal or external. Internal modulation implies direct
modification of the operation of the laser. External modulation is a modification of the
light beam after its emission by the laser. The intensity, the frequency, the phase and the
polarisation can be modulated. Phase and polarisation modulation are external. Intensity
and frequency modulation can be internal or external.
2.6.4 Transmission Loss:
Transmission loss reduces to free space loss:
L=(λ/4πR)2
(2.5)
Where λ is the wavelength and R is the distance between transmitter and reveiver.
12
13. 2.6.5 Reception:
The receiving gain of the antenna is given by:
GR=(πDR/λ)2
Where DR is the effective diameter of the receiver antenna.
The receiver can be of the direct detection type (Figure 2.8) or a coherent
detection receiver (Figure 2.9). With direct detection, the incident photons are converted
into electrons by a photodetector. The subsequent baseband electric current at the
photodetected output is amplified then detected by a matched filter.
With coherent detection, the optical signal field associated with the incident photons is
mixed with the signal from a local laser. The resulting optical field is converted into a
bandpass electric current by a photodetector and is subsequently amplified by an
intermediate frequency amplifier. The demodulator detects the useful signal either by
envelope detection or by coherent demodulation.
The receiving losses include optical transmission losses, and for coherent
detection, losses associated with the degradation of the wavefront (the quality of the
wavefront is an important characteristic for optimum mixing of the received signal field
and the local oscillator field at the photodetector front end). Filtering reject out-of-band
photons, also introduces losses, since the transmission coefficient reduces with
bandwidth. A typical filter width is from 0.1 to l00nm.
Figure 2.8 Optical ISL direct detection receiver
Figure 2.9 Optical ISL coherent detection receiver.
The signal-to-noise power ratio at the detector output depends on the type of detection.
Coherent detection confers a higher value of S/N than direct detection. Unless high data
rates are involved, there is no advantage in weight or power from using coherent
13
14. detection techniques for communications along with a separate direct detection receiver
for acquisition and tracking.
2.7 Conclusion:
Intersatellite links permit the following:
• The use of a geostationary satellite as a relay for permanent links between low
orbit satellites and a network of a small number of earth stations.
• An increase in system capacity by combining the capacities of several
geostationary satellites.
• The planning of systems with a higher degree of flexibility.
• Consideration of systems providing a permanent link and worldwide coverage
using low orbit satellites as an alternative to systems using geostationary
satellites.
Optical technology is more advantageous in terms of mass and power consumption for
high capacity links.
14
15. 3. Global achievements:
Space-based optical communications development around the world has been
primarily supported by government agencies. The European Space Agency, the Japanese
government, and NASA and the DOD in the United States have been the main funding
agencies. This is changing as the commercial satellite world integrates optical ISLs, and
companies will be willing to form partnerships and invest more of their own independent
research and development funds.
3.1 Japan
The Japanese have a strong program in optical communications. The Science and
Technology Agency has designated the Communications Research Laboratory (CRL) of
the Ministry of Posts and Telecommunications as a Center of Excellence for Optical
Communications and Sensing. Thus the government has determined that optical
communications and optical technologies, including sensing, are extremely important
issues for Japan. As a Center of Excellence, the CRL has gathered researchers from
around the world and devoted a lot of money for developments in this area. An overview
of the types of links and systems being considered, from ISLs to space-earth links, is
shown in Figure 3.1. A comment was made during the site visit to CRL that all ISLs of
the future would be optical.
Figure. 3.1. Japanese Optical Communications System Plan (CRL).
3.1.1Engineering Test Satellite VI (ETS-VI)
ETS-VI was intended to go into GEO. It did not achieve this, however, and lasted
from 1994 to 1996, its lifespan a result of the effects of being in the wrong orbit. CRL
and NASA's Jet Propulsion Laboratory (JPL) were able to do some space-earth
experiments during the life of the spacecraft. It provided a bi-directional link at 1.024
Mbps using intensity modulation and direct detection (IM/DD). The spacecraft used a 7.5
cm diameter telescope. The downlink used a 0.83 µm, 13.8 mW AlGaAs laser diode. The
15
16. uplink was at 0.51 µm using an argon laser from a 1.5 m telescope in Tokyo. The Laser
Communications Experiment (LCE) is shown in Figure 3.2. Its mass was 22.4 kg and it
consumed 90 W max
Figure. 5.2. ETS-VI LCE.
3.1.2 Optical Inter-Orbit Communications Engineering Test Satellite
(OICETS)
OICETS, which was launched into LEO in 2000 carrying an optical terminal is
compatible with the European SILEX terminal and will communicate with the ESA
ARTEMIS satellite in GEO. The Laser Utilizing Communications Experiment (LUCE)
will have a 26 cm telescope with a 50 Mbps intensity modulated 0.847 µm, 200 mW laser
diode link to ARTEMIS and a 2.048 Mbps direct detection link at 0.819 µm from
ARTEMIS.
3.2 Europe
In Europe, ESA has been a primary driver in the development of optical
communications although there have been a number of national efforts also.
The Advanced Relay and Technology Mission (Artemis) of the European Space Agency
(ESA) carries payloads for the demonstration and promotion of advanced technologies
and services, in particular data relay, land mobile communications and navigation.
Artemis was launched aboard Ariane 5 on July 12, 2001, but failed to reach geostationary
orbit due to a malfunction on the launcher. After 300 days of operation using electric
propulsion for orbit control Artemis was placed successfully into geostationary orbit on
January 31, 2003.
16
18. 3.2.1 Optical Ground Station has sights set on Artemis
The OGS, located at the Instituto de Astrofisica de Canarias' (IAC) Observatorio
del Teide in Tenerife, will be used for the commissioning and later for periodic checkouts
of the laser communication terminal onboard Artemis.
To perform laser communication from ground to space, the sky must be perfectly
clear, without any clouds, and the path through the atmosphere must be as short as
possible. Both conditions are satisfied at the Observatorio del Teide, which is situated
above cloud level at 2400 metres altitude and is the closest point to the equator in an ESA
member state.
Figure 3.5OGS telescope
3.2.2A world first : Data transmission between European satellites using laser light
On 22 November 2001, for the first time, a data link between satellites was
established using a laser beam as signal carrier. On board ESA's Artemis satellite launched last July 2001 by an Ariane 5 - is the SILEX system. This system provides an
optical data transmission link with the CNES Earth observation satellite SPOT 4, which
is orbiting the earth at an altitude of 832 km while Artemis is temporarily in a parking
orbit
at
31
000
km.
Through the laser data link, images taken by SPOT 4 can be transmitted in real time to
the image processing centre at Spot Image in Toulouse, France, via Artemis, thus
drastically reducing the time between taking the picture and its delivery to the centre.
This is possible whenever the two satellites are in line of sight. Without the Artemis relay
the images are stored on board in SPOT 4's memory and dumped to the ground stations.
The experiment performed last night consisted in establishing the link four times: in the
course of four successive SPOT 4 orbits, the SILEX terminal on board Artemis activated
its optical beacon to scan the area where SPOT was expected to be. When contact was
made, SPOT 4 responded by sending its own laser beam to Artemis. On receiving the
SPOT 4 beam, Artemis stopped scanning and the optical link was maintained for a preprogrammed period lasting from 4 to 20 minutes.
During the period when the two satellites were "communicating", test data were
transmitted from SPOT 4 to the ground via Artemis at a rate of 50 000 000 bits per
second (50 Mbps). The extremely high accuracy of the data stream was confirmed at
ESA's test station in Redu (Belgium) and the SPOT 4 receive station in Toulouse.
The main challenge in establishing an optical link between satellites is to point a very
18
19. narrow beam with extreme accuracy to illuminate the partner spacecraft flying at a speed
of 7000 m/s. Last night's experiment was performed under worst-case conditions since
Artemis is not in its nominal geostationary position but in an lower parking orbit, circling
the Earth every 19 hours.
This experiment was preceded by a series of tests a week earlier, during which a link was
established between Artemis and ESA's optical ground station in Tenerife. Thoses tests
demonstrated the correct operation of the SILEX terminal and paved the way for the
subsequent steps.
The SILEX system consists of two terminals: one on board Artemis, the other on
SPOT 4. Both terminals were designed and built by Astrium. The definition and
procurement of the system were conducted in close cooperation between ESA and the
French space agency, CNES.
Figure 3.6 Artemis and SPOT 4 communicating via the SILEX system - Artist's impression.
3.2.3Successful optical data relay link between OICETS and Artemis
On 9 December 2005 the first bi-directional optical link between KIRARI, the
Japanese satellite officially called OICETS (which stands for "Optical Inter-orbit
Communications Engineering Test Satellite"), and ESA’s Artemis was made on Friday 9
December 2005.
KIRARI (meaning “glitter” or “twinkle” in Japanese) is the second optical data relay
satellite using Artemis, following the world premiere laser link with SPOT-4 in
November 2001 in the framework of the SILEX development, an innovative payload
which provides a laser beam as a data signal carrier. This optical service has operated
regularly since then and accumulated more than 1100 links totalling 230 hours to date.
The KIRARI experiment is the result of a long standing agreement between JAXA, the
Japan Aerospace Exploration Agency, and ESA for cooperation on data relay services,
and builds upon the SILEX development.
KIRARI has, for the first time, used an optical link for both data and command
transmission. The quality of the link was excellent.
19
20. The optical link experiment between KIRARI and Aretemis will continue through
2006, making several optical links under different environmental conditions to
completely qualify and characterize the KIRARI technology.
KIRARI, which is in low earth orbit at an altitude of about 600 km. As with the
SILEX development, the KIRARI link carries data at 50 Mbps in the return direction
between KIRARI and the ground, and 2 Mbps in the forward direction between ground
and satellite. The transmissions through Artemis are linked to the ESA ground station at
Redu, Belgium, which is connected via data lines to the KIRARI control centre at
Tsukuba, Japan.
3.2.4Another world first for Artemis: a laser link with an aircraft
On 18 December 2006 Artemis, successfully relayed optical laser links from an
aircraft. These airborne laser links, established over a distance of 40 000 km during two
flights at altitudes of 6000 and 10 000 meters, represent a world first.
The relay was set up through six two-way optical links between a Mystère 20
equipped with the airborne laser optical link LOLA (Liaison Optique Laser Aéroportée)
and the SILEX laser link payload on board ARTEMIS in its geostationary orbital position
at 36 000 kilometres altitude: a feat equivalent to targeting a golf ball over the distance
between Paris and Brussels.
Figure 3.7Artemis laser link to aircraft
Figure 3.8 LOLA telescope assembly
20
21. 4. Optical Satellite Networks- The future:
This work is built on the premise that optical space communication at very high
rates ( 10 Gb/s) between satellites is now feasible. It is reasonable to believe as more
space packages are built and extensive on-orbit-operation experience develops in the next
few years, the cost of high-rate optical crosslinks will be substantially lower than their
microwave functional equivalent. A natural next step with such a powerful enabling
technology is the realization of an optical satellite network of global extent. This optical
satellite network can in turn revolutionalize space system architectures that may use the
network as a critical subsystem. Examples of these space systems include those offering
communication services or remote sensing.
We will summarizes briefly the state-of-the-art of optical crosslink technology,
examines architectures (from the physical layer to the application layer)
that combine other technologies to form an integrated space and terrestrial network, and
finally explores the space of possible revolution in network performance and applications
that are enabled by such a key technology innovation.
Figure 4.1 illustrates the general concept of an optical space network and its
possible user community. It can simultaneously serve a number of applications such as
data readout of space sensors, support of space exploration, and science missions and
act as the conduit for data communications for fixed ground terminals and mobile
spaceborne, airborne, seaborne, and ground vehicles. The primary links through the
atmosphere are assumed to be microwave due to poor optical propagation in bad weather
conditions. However, we will mention technologies for special applications where optical
downlinks from satellite to airborne and ground terminals are viable if absolute allweather availability is not required. Note that this space backbone can be in
high/geosynchronous (GEO; 40 000 Km altitude), medium (MEO; 5000–15 000 Km), or
low (LEO; 1000–2000 Km) earth orbits.
Figure 4.2 specifically gives an example of two LEO constellations
interconnected by optical crosslinks and connected to terrestrial user terminals and
interconnected with fiber and wireless networks via “gateways” forming a global
heterogeneous network. Data networks based on such LEO, MEO, or GEO constellation
topologies will be an important future alternative to provide global data networking
services, especially in areas of poor or congested terrestrial infrastructure deployment,
and in mobile and quick deployment application scenarios.
21
22. Figure 41. General concept of an optical space network and its possible user community
Figure 4.2. Example of an integrated satellite and terrestrial network.
22
23. Space networking as an application area spans many different aspects of
communication and relay services. Figure 4.3 depicts these applications in a logical tree
structure. The important forefronts as highlighted are data networking services for nearearth applications with emphasis on bursty computer traffic in both access and trunking.
Figure 4.3. New and important development area for space networking.
To serve a wide variety of usage, this network probably will have a hierarchical
architecture, as shown in Figure 4.4. Thus, the optical satellite network is a direct analog
of the terrestrial network.
Figure 4.4. Hierarchical space network architecture—wide/metro/local-area networks.
23
24. As shown in chapter 2 RF links require much larger aperture size than an optical
link. Moreover, since the carrier frequencies of optics are very high ( 200 THz), each
optical carrier can accommodate very high data rates ( 100 Gb/s) without the nasty
dispersion effects of fiber, and there is the possibility of using wavelength-division
multiplexing (WDM) to further increase the data rate per optical beam. There is no doubt
that optical crosslink technology will greatly revolutionalize space system architectures.
We can summarize the distinguishing good properties of optical crosslinks with
the following general characteristics, for high rates such as 10 Gb/s:
1) Small antenna sizes ( 30 cm), compared to several feet for RF systems;
2) Modest weight ( 100 lb) and power ( 100 W), compared to several hundred pounds and
several hundred watts for RF systems;
3) Continuous operations with the sun in or near the field of view;
4) Easy multiplexing, demultiplexing, switching, and routing for network applications;
5) Much lower cost than RF systems.
An optical space communication system can be partitioned into three interacting
subsystems each with their separate critical design issues. These three subsystems are:
1) Opto/mechanical/thermal subsystem;
2) Spatial acquisition and tracking subsystem;
3) Communication subsystem.
Note that these are logical partitions and not physical partitions. The subsystems, such as
the tracking and optical subsystems, may share common physical hardware.
4.2 Optical Satellite Network Architecture:
There can be two reasons an optical satellite network is economically viable. The
first is that for long-distance intercontinental transmissions, it can be cost-competitive
with undersea fiber systems and can become an alternative for terrestrial networks. One
interesting property space optical communications has is that the power attenuation due
to free-space diffraction loss is only inversely proportional to the square of the link
distance, whereas optical fiber attenuation is exponential in distance and
amplifiers/repeaters at regular distances are required to maintain performance. Given
long enough link distance, the total attenuation seen by the fiber link will become much
larger than that seen by the space optical link. In , a simple life-cycle cost comparison of
equal capacities in 10-Gb/s quanta was performed. The per-year operating costs are
normalized with respect to system lifetime cost ( 10 years for space systems), included
nonrecurrent engineering, production, deployment, and operating costs. The crossover
between the two systems is estimated to be around 5000 Km (using undersea fiber
systems as a benchmark and based on best guessed optical crosslink and RF up- and
downlink technology costs).
The second reason is that the optical satellite network may provide unique
services to space missions and open-air-interface accesses such as voice and data
communications over microwave satellite systems for mobile platforms and remote users
with no broadband wired access, and satellite and terrestrial distributed sensing readout.
24
25. 4.2.1 Interfaces to RF and Other Access Links and to the Terrestrial Network:
Figure 4.5 depicts the various interfaces of the optical satellite network:
microwave and optical trunk connections to the terrestrial WAN, metro-area network,
and LAN interconnections via microwave up- and downlinks, and microwave and optical
individual user accesses. Though limited in rates ( a small number of gigabits/second
using high spectral efficiency modulation and coding), microwave links will be the
primary connections to the terrestrial network. With this choke point, the optical satellite
network cannot be considered architecturally as a simple extension of the terrestrial
network but rather a separate network with only moderate rate gateway connections ( 10
Gb/s) to the terrestrial WAN. Optical connections through the atmosphere to the ground
can alleviate this choke point, but they can only operate in clear weather and need
multipath diversity to provide any sensible network performance. Microwave satellite
data accesses at high rates require narrow spot antenna beams for high sensitivities and
small user terminals. These can be realized via a multiple beam antenna system using a
microwave lens or a microwave phase array.
Figure 4.5 Interfaces of the optical satellite network
4.2.2 Physical Network Topology
The primary goal of a backbone constellation is to provide the coverage as
required by the users. Users are in LEO, MEO, GEO, and the relevant parts of highly
elliptical orbits, as well as airborne and on the ground. These coverage requirements can
be met by a variety of constellations, with different altitudes, number of orbital planes,
arrangement of the orbits, and arrangement of satellites within the orbits. All of these
factors will influence the complexity and performance of the overall system. Given that
GEO is the configuration of choice for the backbone of a satellite network, the capacities
of the links in this backbone may reach 100 Gb/s and optical links are the only viable
candidates. An interesting benefit of a free-space link is that when the traffic load shifts,
25
26. the physical connection topology can be easily changed via pointing the telescopes to a
new satellite, and load balancing can be implemented more easily.
4.2.3 Spacecraft Node Switching Architecture:
The backbone optical satellite network nodes must be designed to support
necessary network functions just like their terrestrial network counterparts. The current
terrestrial networks have backbone routers that deal with the long haul traffic and access
routers for aggregation. These data network services may themselves co-exist on the
same fiber plant with circuit-switched oriented services. Figure 4.6 shows the connection
architecture for an optical satellite network backbone node. A significant difference from
a terrestrial backbone node is that the satellite node will also have to deal with accesses
from individual users and thus have an aggregation function as well.
Figure 4.6 Optical satellite node connection architecture.
Figure 4.7 depicts a backbone constellation with WDM access links and optical
wavelength switching at the relay nodes. The node will also have to deal with RF access
links. These can be demodulated and multiplexed onto an optical wavelength or can be
subcarrier-modulated onto a wavelength, losing some power efficiency but gaining
hardware simplification in the process.
4.2.4 Intraspacecraft Optical Network (Spacecraft-LAN)
All-optical switching and routing at an optical satellite network node is formatinsensitive to the traffic but will lose some link quality in the form of signal-to-noise ratio
degradation. Format insensitivity may be a significant advantage for optical satellite
systems since space systems are designed and deployed years ahead of user services.
Analog space links with high linearity and low distortions can be supported easily by alloptical switching onboard the spacecraft. This gain must be traded off against the loss of
link performance over a fully regenerative relay node. A likely architecture for the
satellite relay node is that the core backbone has circuit provisioning and switching and
26
27. only accesses are routed and electronically processed. Thus, all relay nodes are logically
one hop away from all the other nodes when viewed at Layer 3, the network layer. Some
wavelength efficiency may be sacrificed, but it is a good trade for electronic processing
hardware complexity.
Figure 4.7 Optical satellite network WDM switching node.
4.2.5 Optical Links to the Ground and Aircraft—Clear Air Links:
It is possible in clear weather conditions to communicate optically to a user
terminal from space, especially if the terminal is located on a high-flying aircraft such as
an airliner (Figure 4.8). It is also the only viable link (albeit at lowrates due to significant
phase front distortions as the optical beam propagate through the plasma generated) to the
space shuttle during its RF blackout period during reentry.
Spatial, temporal, and frequency diversity architectures are candidates for fade
mitigation of the received signal. A diversity system statistically guarantees that at least
one of the independent paths has good quality. In contrast to spatial diversity for wireless
systems, spatial diversity for atmospheric optical systems can be readily implemented
since the intensity and phase coherence length is on the order of centimeters, i.e., multiple
transmitters or receivers only need to be placed centimeters apart to see approximately
independent channel fades.
4.2.6 Optical Multiple Access:
In a number of specialized applications, multiple users can be within the same
field of view of the satellite receiving telescope. From geosynchronous orbit, users more
than 100 m apart can be resolved by multiple focal plane detectors of a modest telescope
of 10 cm in diameter. However, for many lower rate random access users, such as those
27
28. on airliners, it is prohibitively costly to assign one optical receiver per user even if it is
dynamically scheduled. Thus, an optical multiple-access receiver combining the signals
of a larger group of users at the same detector makes sense.
Figure 4.8 Optical links over clear atmosphere and boundary layer turbulence.
4.3 Summary:
Not very often in the history of communications and networking have there been
truly transforming inventions that result in quantum leaps in the nature of services or
costs to the end users. Optical satellite communications will likely be classified as one
such transforming technology if its architectural implications are fully exploited. Not
only will the satellite network become economically viable, but also its deployment and
the extraordinary services it can offer are capable of radically transforming space system
architectures.
To make a space network cost competitive, it is imperative that the best designs
be used. An unimaginative network will use the optical link as a backbone or a highspeed entrance link, which by itself may to some be transforming enough. The
opportunity is now to use imagination and creativity to bring home this new breakthrough
in satellite networking and none too soon, given the state of stagnation in the aerospace
community.
28
29. 5. References:
1. G.Maral, M. Bousquet “ Satellite Communications Systems: Systems, Techniques
and Technology” 3rd ed., Wiley Series in Communications And Distributed
Systems.
2. Vincent W.S. Chan, Fellow IEEE, Fellow, OSA “ Optical Satellite Networks”,
IEEE Jornal Of Lightwave Technology , Vol.12, No. 11, Nov 2003 pp.2811-2827
3. “Encyclopedia of laser Physics and Technology”, www.rp-photonics.com
4. European Space Agency. www.ESA.org
29