7SJ62 Multifunction Over Current Protection Relayashwini reliserv
The SIPROTEC 4 7SJ62 relays can be used for line protection of high and medium voltage networks with earthed (grounded), low-resistance earthed, isolated or compensated neutral point. With regard to motor protection, the SIPROTEC 4 7SJ62 is suitable for asynchronous machines of all sizes. The relay performs all functions of backup protection supplementary to transformer differential protection. 7SJ62 is featuring the "flexible protection functions". Up to 20 protection functions can be added according to individual requirements. Thus, for example, a rate-of-frequency-change protection or reverse power protection can be implemented.
These slides present the introduction to FACTS devices. Later we will discuss about its modelling and control aspect applications. This comes under the topic on power electronics application in smart and microgrid systems.
A general presentation on IEC 61850 application to substation automation.
Describes Data Semantics, communication services and the substation configuration language
HVDC Bridge and Station Configurations
1. General HVDC – HVAC Comparisons
2. Components of a Converter Bridge
3. HVDC scheme configurations
Operation of the HVDC converter
1. General assumptions
2. Rectifier operation with uncontrolled valves and X = 0
3. Rectifier operation with controlled valves and X = 0
4. Rectifier operation with controlled valves and X 0
5. Inverter operation with controlled valves and X 0
6. Commutation and Commutation Failure
7. Reactive Power Requirements
8. Short-circuit capacity requirements for an HVDC terminal.
9. Harmonics and filtering on the AC and DC sides
7SJ62 Multifunction Over Current Protection Relayashwini reliserv
The SIPROTEC 4 7SJ62 relays can be used for line protection of high and medium voltage networks with earthed (grounded), low-resistance earthed, isolated or compensated neutral point. With regard to motor protection, the SIPROTEC 4 7SJ62 is suitable for asynchronous machines of all sizes. The relay performs all functions of backup protection supplementary to transformer differential protection. 7SJ62 is featuring the "flexible protection functions". Up to 20 protection functions can be added according to individual requirements. Thus, for example, a rate-of-frequency-change protection or reverse power protection can be implemented.
These slides present the introduction to FACTS devices. Later we will discuss about its modelling and control aspect applications. This comes under the topic on power electronics application in smart and microgrid systems.
A general presentation on IEC 61850 application to substation automation.
Describes Data Semantics, communication services and the substation configuration language
HVDC Bridge and Station Configurations
1. General HVDC – HVAC Comparisons
2. Components of a Converter Bridge
3. HVDC scheme configurations
Operation of the HVDC converter
1. General assumptions
2. Rectifier operation with uncontrolled valves and X = 0
3. Rectifier operation with controlled valves and X = 0
4. Rectifier operation with controlled valves and X 0
5. Inverter operation with controlled valves and X 0
6. Commutation and Commutation Failure
7. Reactive Power Requirements
8. Short-circuit capacity requirements for an HVDC terminal.
9. Harmonics and filtering on the AC and DC sides
this slide shows what is smart grid ,its comparison between the electromechanical grids . smart meters and devises for the smart grid . benefit of smart grid . and a conclution
Design of a generating substation with the description of designing a transformer. Here we show some basic components of a substation. and we also show the parameters and calculation to design a transformer of a specific ratings.
Data Center Lessons Learned at an Intel data center. Innovations in cost and energy savings in high-density data centers including: air economizer, retrofit of factory builiding, high efficiency air-cooled cabinets, and a container data center proof-of-concept.
The data center market has expanded dramatically in the past few years, and it doesn’t show signs of slowing down. Many clients and building owners are requesting modular data centers, which can be placed anywhere data capacity is needed. Modular data centers can help cash-strapped building owners add a new data center (or more capacity) to their site, and can assist facilities with unplanned outages, such as disruptions due to storms. Owners look to modular data centers to accelerate the “floor ready” date as compared to a traditional brick and mortar.
Basics of Power systems
Network topology
Transmission and Distribution
Load and Resource Balance
Economic Dispatch
Steady State System Analysis
Power flow analysis
Dynamic System Analysis
Transient stability
Turnkey Solutions – the key to successful projects
----------------------------------------------------------------
EPC Solutions has all it takes to design, construct, and operate turnkey electrical substation solutions that efficiently support the reliable supply of electrical power on all voltage levels: decades of practical experience as a contractor and equipment manufacturer and a vast number of successfully completed projects all over the world, unparalleled expertise in all transmission processes, and proven excellence in project management. A distinguished tradition of innovation in power engineering, customized financing solutions, and outstanding quality standards in all production facilities worldwide round out the picture.
EPCS turnkey solutions for high-voltage substations incorporate the strong performance of one of the world’s leading engineering companies and one-stop supplier of power transmission products, solutions, and services. The scope of services comprises consulting, project management, system planning, engineering, commissioning, and comprehensive after-sales support. Centers of competence and branches all over the world create local value and ensure that EPCS experts are within close reach of every project.Customers worldwide benefit from numerous advantages of high-voltage substations from EPCS:
>One-stop approach comprising all technical, financial, and ecological aspects of the station’s entire life cycle
>Customized solutions based on proven EPCS technologies, even for the most challenging demands
>Freedom from coordination efforts and minimized financial and technical risk
this slide shows what is smart grid ,its comparison between the electromechanical grids . smart meters and devises for the smart grid . benefit of smart grid . and a conclution
Design of a generating substation with the description of designing a transformer. Here we show some basic components of a substation. and we also show the parameters and calculation to design a transformer of a specific ratings.
Data Center Lessons Learned at an Intel data center. Innovations in cost and energy savings in high-density data centers including: air economizer, retrofit of factory builiding, high efficiency air-cooled cabinets, and a container data center proof-of-concept.
The data center market has expanded dramatically in the past few years, and it doesn’t show signs of slowing down. Many clients and building owners are requesting modular data centers, which can be placed anywhere data capacity is needed. Modular data centers can help cash-strapped building owners add a new data center (or more capacity) to their site, and can assist facilities with unplanned outages, such as disruptions due to storms. Owners look to modular data centers to accelerate the “floor ready” date as compared to a traditional brick and mortar.
Basics of Power systems
Network topology
Transmission and Distribution
Load and Resource Balance
Economic Dispatch
Steady State System Analysis
Power flow analysis
Dynamic System Analysis
Transient stability
Turnkey Solutions – the key to successful projects
----------------------------------------------------------------
EPC Solutions has all it takes to design, construct, and operate turnkey electrical substation solutions that efficiently support the reliable supply of electrical power on all voltage levels: decades of practical experience as a contractor and equipment manufacturer and a vast number of successfully completed projects all over the world, unparalleled expertise in all transmission processes, and proven excellence in project management. A distinguished tradition of innovation in power engineering, customized financing solutions, and outstanding quality standards in all production facilities worldwide round out the picture.
EPCS turnkey solutions for high-voltage substations incorporate the strong performance of one of the world’s leading engineering companies and one-stop supplier of power transmission products, solutions, and services. The scope of services comprises consulting, project management, system planning, engineering, commissioning, and comprehensive after-sales support. Centers of competence and branches all over the world create local value and ensure that EPCS experts are within close reach of every project.Customers worldwide benefit from numerous advantages of high-voltage substations from EPCS:
>One-stop approach comprising all technical, financial, and ecological aspects of the station’s entire life cycle
>Customized solutions based on proven EPCS technologies, even for the most challenging demands
>Freedom from coordination efforts and minimized financial and technical risk
The Roxtec BGTM product family is designed to safely and efficiently bond or ground armored and shielded cables through a single cut-out or open- ing in a wall, floor or electrical enclosure. The product provides a secure means of cable terminations and pass-throughs, provides an environmental and fire resistant seal, and establishes a secure bonding path to ground for metallic cable components. The product is certified for use in hazardous locations where required by local codes and regulations. The Roxtec BGTM system complies with EU directive 2002/95/EC, Restriction of Hazardous Substances (RoHS).
Roxtec Cable Transits - Installing & Terminating Substation Cables
Roxtec cable transits provide several clear advantages for installing and terminating cables in industrial and high voltage substations. Roxtec cable transits provide a standardised design with the flexibility to terminate a variety of different sizes and cable constructions. The ease of cable installation reduces labour costs and minimises the potential for cable insulation damage. The structural and environmental integrity of the wall or floor penetration is maintained providing an insulated, vapor-tight and fire-stop barrier and cables can be easily added for future up-grading. Roxtec cable transits are a viable alternative for terminating cables into industrial power substations.
Cembre B135C Hydraulic Crimping Tool - Battery Crimping Tools
14.4V cordless hydraulic battery crimping tool
Lightweight and balanced Cembre crimper for single hand operation
Double speed crimping action
Cembre crimping head can rotate through 180°
Quiet in operation with very little vibration
Operating buttons mechanically interlocked to prevent accidental operation
Microprocessor control with automatic motor cut out on completion of the crimping operation
Fitted with a maximum hydraulic pressure valve
Cembre B135C Battery Crimpers - Crimping Applications
HV & LV cable lugs - 400sqmm
HV & LV cable splices - 240sqmm
Insulated cable terminals - 240sqmm
C Sleeve connectors - 185sqmm
Batra Henlay Cables provides superior quality copper flexible wires, control instrumentation, telecommunication cables moreover high defined coaxial cables in various forms of insulation to the power, telecommunication, and energy industries.
author: International Team
publisher: Daniel Garrido
licence: Creative Commons
place: University of Southern Denmark- Odense
@fomenting colaborational knowledge
Isolation Procedures for Safe Working on Electrical Systems and Equipment by the JIB | solation Procedures for Safe Working on Electrical Systems and Equipment
This chart shows the safe isolation procedure that you should use when working on electrical systems and equipment.
You'll receive a printed copy of this from your Training Provider, but it's also here as a handy reference to keep electronically.
THE RULES OF SAFE ISOLATION ARE:
Obtain permission to start work (a Permit may be required in some situations)
Identify the source(s) of supply using an approved voltage indicator or test lamp
Prove that the approved voltage indicator or test lamp is functioning correctly
Isolate the supply(s)
Secure the isolation
Prove the system/equipment is DEAD using an approved voltage indicator or test lamp
Prove that the approved voltage indicator or test lamp is functioning correctly
Put up warning signs to tell other people that the electrical installation has been isolated
Once the system/equipment is proved DEAD, work can begin
Uploaded by THORNE & DERRICK LV HV Jointing, Earthing, Substation & Electrical Eqpt | Explosive Atmosphere Experts & ATEX IECEx.
THORNE & DERRICK based in the UK are international distributors of LV, MV & HV Cable Installation, Jointing, Substation & Electrical Equipment.
Since 1985, T&D have established an international reputation based on SERVICE | INTEGRITY | TRUST.
Contact us for 3M, ABB, Alroc, AN Wallis, CATU, Cembre, Centriforce, CMP, CSD, Elastimold, Ellis Patents, Emtelle, Euromold, Filoform , Furse, Lucy Electric & Zodion, Nexans, Pfisterer, Polypipe, Prysmian, Roxtec, Sicame, WT Henley.