Orthogonal Frequency Division Multiplexing, OFDM uses a large number of narrow sub-carriers for multi-carrier transmission to overcome the effect of multi path fading problem. LTE uses OFDM for the downlink, from base station to terminal to transmit the data over many narrow band careers of 180 KHz each instead of spreading one signal over the complete 5MHz career bandwidth. OFDM meets the LTE requirement for spectrum flexibility and enables cost-efficient solutions for very wide carriers with high peak rates.
The primary advantage of OFDM over single-carrier schemes is its ability to cope with severe channel conditions. Channel equalization is simplified. The low symbol rate makes the use of a guard interval between symbols affordable, making it possible to eliminate inter symbol interference (ISI).
Orthogonal Frequency Division Multiplexing, OFDM uses a large number of narrow sub-carriers for multi-carrier transmission to overcome the effect of multi path fading problem. LTE uses OFDM for the downlink, from base station to terminal to transmit the data over many narrow band careers of 180 KHz each instead of spreading one signal over the complete 5MHz career bandwidth. OFDM meets the LTE requirement for spectrum flexibility and enables cost-efficient solutions for very wide carriers with high peak rates.
The primary advantage of OFDM over single-carrier schemes is its ability to cope with severe channel conditions. Channel equalization is simplified. The low symbol rate makes the use of a guard interval between symbols affordable, making it possible to eliminate inter symbol interference (ISI).
Massive MIMO (also known as “Large-Scale Antenna Systems”, “Very Large MIMO”, “Hyper MIMO”, “Full-Dimension MIMO” and “ARGOS”) makes a clean break with current practice through the use of a large excess of service-antennas over active terminals and time division duplex operation. Extra antennas help by focusing energy into ever-smaller regions of space to bring huge improvements in throughput and radiated energy efficiency. Other benefits of massive MIMO include the extensive use of inexpensive low-power components, reduced latency, simplification of the media access control (MAC) layer, and robustness to intentional jamming. The anticipated throughput depend on the propagation environment providing asymptotically orthogonal channels to the terminals, but so far experiments have not disclosed any limitations in this regard. While massive MIMO renders many traditional research problems irrelevant, it uncovers entirely new problems that urgently need attention: the challenge of making many low-cost low-precision components that work effectively together, acquisition and synchronization for newly-joined terminals, the exploitation of extra degrees of freedom provided by the excess of service-antennas, reducing internal power consumption to achieve total energy efficiency reductions, and finding new deployment scenarios.
UMTS Long Term Evolution, LTE, is the technology of choice for the majority of network operators worldwide for providing mobile
broadband data and high-speed internet access to their subscriber base. Due to the high commitment LTE is the innovation platform
for the wireless industry for the next decade.
This class will provide the basics of this fascinating technology. After attending this course you will have an understanding of
OFDM-principles including SC-FDMA as the transmission scheme of choice for the LTE uplink. Multiple antenna technology (MIMO),
a fundamental part of LTE, will be explained as well as its impact on the design of device and network architecture. We’ll give a quick
introduction into the evolution of this technology including future upgrades of LTE features like multimedia broadcast, location based
services and increasing bandwidth through carrier aggregation.
The second part of the course will provide an overview including practical examples and exercises on how to test a LTE-capable device
while performing standardized RF measurements such as power, signal quality, spectrum and receiver sensitivity. We’ll address how
to automate these measurements in a simple and cost-effective way. We will introduce application based testing by demonstrating
end-to-end (E2E), throughput and application testing using the Rohde & Schwarz R&S®CMW500 Wideband Radio Communication
Tester. Examples of application tests are voice over LTE, VoLTE or Video over LTE.
COMPARISON OF BER AND NUMBER OF ERRORS WITH DIFFERENT MODULATION TECHNIQUES I...Sukhvinder Singh Malik
This paper provides analysis of BER and Number of Errors for MIMO-OFDM wireless communication system by using different modulation techniques. Wireless designers constantly seek to improve the spectrum efficiency/capacity, coverage of wireless networks, and link reliability. So the performances of the wireless communication systems can be enhanced by using multiple transmit and receive antennas, which is generally referred to as the MIMO technique. Here analysis will be carried out for an OFDM wireless communication system using different modulation techniques and considering the effect and the wireless channel like AWGN, fading. Performance results will be evaluated numerically and graphically using the plots of BER versus SNR and plots of number of errors versus SNR.
Design Ofdm System And Remove Nonlinear Distortion In OFDM Signal At Transmit...Rupesh Sharma
although OFDM seems to be a solution to keep up with
the demand of increasing data rates, it has some drawbacks.
Sensitivity to high PAPR is the most significant of these
drawbacks. The main objective of this paper was to investigate
and document the effects of PAPR on the performance of OFDM
based digital communications under different channel conditions.
A step-by-step approach was adopted in order to achieve the
objective of this paper. The first step is to provide a basic
background on the principles of OFDM. The reasons for the
PAPR and a theoretical analysis of these effects on OFDM
systems are documented. The OFDM system has a high peak-toaverage
power ratio (PAPR) that can cause unwanted saturation
in the power amplifiers, leading to in-band distortion and out-ofband
radiation. To be able to observe the system behavior, the
simulation results for different channel models are presented in
graphical form. Next, the simulation results obtained in this work
are compared to the simulation results reported in related studies
Performance enhancement of maximum ratio transmission in 5G system with multi...IJECEIAES
The downlink multi-user precoding of the multiple-input multiple-output (MIMO) method includes optimal channel state information at the base station and a variety of linear precoding (LP) schemes. Maximum ratio transmission (MRT) is among the common precoding schemes but does not provide good performance with massive MIMO, such as high bit error rate (BER) and low throughput. The orthogonal frequency division multiplexing (OFDM) and precoding schemes used in 5G have a flaw in high-speed environments. Given that the Doppler effect induces frequency changes, orthogonality between OFDM subcarriers is disrupted and their throughput output is decreased and BER is decreased. This study focuses on solving this problem by improving the performance of a 5G system with MRT, specifically by using a new design that includes weighted overlap and add (WOLA) with MRT. The current research also compares the standard system MRT with OFDM with the proposed design (WOLA-MRT) to find the best performance on throughput and BER. Improved system results show outstanding performance enhancement over a standard system, and numerous improvements with massive MIMO, such as best BER and throughput. Its approximately 60% more throughput than the traditional systems. Lastly, the proposed system improves BER by approximately 2% compared with the traditional system.
Multicarrier modulation can be implemented by using Orthogonal Frequency Division Multiplexing (OFDM) to achieve utmost bandwidth exploitation and soaring alleviation attributes profile besides multipath fading. To support delay sensitive and band bandwidth demanding multimedia applications and internet services, MIMO in addition with other techniques can be used to achieve high capacity and reliability. To obtain high spatial rate by transmitting data on several antennas by using MIMO with OFDM results in reducing error recovery features and the equalization complexities arise by sending data on varying frequency levels. Three parameters frequency OFDM, Spatial (MIMO) and time (STC) can be used to achieve diversity in MIMO-OFDM. This technique is dynamic and well-known for services of wireless broadband access. MIMO if used with OFDM is highly beneficial for each scheme and provides high throughput. There are several space time block codes to exploit MIMO OFDM; one of the techniques is called Alamouti Codes. The paper investigates adaptive Alamouti Codes and their application in IEEE 802.11n.
DYNAMIC OPTIMIZATION OF OVERLAPAND- ADD LENGTH OVER MBOFDM SYSTEM BASED ON SN...cscpconf
An important role performed by Zero Padding (ZP) in multi-band OFDM (MB-OFDM) System.
This role show for low-complexity in résistance against multipath interference by reducing
inter-carrier interference (ICI) and eliminating the inter-symbol interference (ISI) Also, zeropadded
suffix can be used to eliminate ripples in the power spectral density in order to conform
to FCC requirements.
At the receiver of MB-OFDM system needs to use of a technique called as overlap-and-add
(OLA). Which maintain the circular convolution property and take the multipath energy of the
channel.
In this paper, we proposed a method of performing overlap-and-add length for zero padded
suffixes. Then, we studied the effect of this method, dynamic optimization of overlap-and-add
(OLA) equalization, on the performance of MBOFDM system on Bit Error Rate (BER) with
AWGN channel and Saleh-Valenzuela (S-V) Multipath channel Model.
In the dynamic optimization OLA, the Length of ZP depends on length of channel impulse
response (CIR). These measures, based on SNR, insert the ZP according to the measurement.
Dynamic optimization of length of ZP improves the Performance of MBOFDM system. In fact
we developed a technique to select the length of ZP as function of SNR and CIR
estimate(repetition). In our simulation this technique improve to 3 dB at BER=10-2 with a
multipath channels CM4.
An important role performed by Zero Padding (ZP) in multi-band OFDM (MB-OFDM) System.
This role show for low-complexity in résistance against multipath interference by reducing
inter-carrier interference (ICI) and eliminating the inter-symbol interference (ISI) Also, zeropadded
suffix can be used to eliminate ripples in the power spectral density in order to conform
to FCC requirements.
At the receiver of MB-OFDM system needs to use of a technique called as overlap-and-add
(OLA). Which maintain the circular convolution property and take the multipath energy of the
channel.
In this paper, we proposed a method of performing overlap-and-add length for zero padded
suffixes. Then, we studied the effect of this method, dynamic optimization of overlap-and-add
(OLA) equalization, on the performance of MBOFDM system on Bit Error Rate (BER) with
AWGN channel and Saleh-Valenzuela (S-V) Multipath channel Model.
In the dynamic optimization OLA, the Length of ZP depends on length of channel impulse
response (CIR). These measures, based on SNR, insert the ZP according to the measurement.
Dynamic optimization of length of ZP improves the Performance of MBOFDM system. In fact
we developed a technique to select the length of ZP as function of SNR and CIR
estimate(repetition). In our simulation this technique improve to 3 dB at BER=10-2 with a
multipath channels CM4.
Integrated approach for efficient power consumption and resource allocation i...IJECEIAES
The growing interest towards wireless communication advancement with smart devices has provided the desired throughput of wireless communication mechanisms. But, attaining high-speed data packets amenities is the biggest issue in different multimedia applications. Recently, OFDM has come up with the useful features for wireless communication however it faces interference issues at carrier level (intercarrier interferences). To resolve these interference issues in OFDM, various existing mechanisms were utilized cyclic prefix, but it leads to redundancy in transmitted data. Also, the transmission of this redundant data can take some more power and bandwidth. All these limitations factors can be removed from a parallel cancellation mechanism. The integration of parallel cancellation and Convolution Viterbi encoding and decoding in MIMOOFDMA will be an effective solution to have high data rate which also associations with the benefits of both the architectures of MIMO and OFDMA modulation approaches. This paper deals with this integrated mechanism for efficient resource allocation and power consumption. For performance analysis, MIMO-OFDMA system is analyzed with three different approaches likeMIMO-OFDM system without parallel cancellation (MIMO-OFDMA-WPC), MIMO-OFDMA System with parallel cancellation (MIMO-OFDMA-PC) and proposed IMO-OFDMA system with parallel cancellation and Convolution Viterbi encoding/decoding (pMIMO-OFDMAPC &CVed) for 4x4 transmitter and receiver. Through performance analysis, it is found that the proposed system achieved better resource allocation (bandwidth) with high data rate by minimized BER rate and achieved least power consumption with least BER.
For MIMO system, (a) Please talk about the advantage and disadvantag.pdfarihantstoneart
For MIMO system, (a) Please talk about the advantage and disadvantage of MIMO technique.
(b) Please explain why we need Cooperative Diversity to replace MIMO in cellular network.
Solution
A)MIMO advantages
• Capacity scales linearly with number of antennas
Channel knowledge/estimation at Rx needed
• MIMO offers potential for
larger data rate
larger spectral efficiency
larger number of users
improved range/coverage
better interference suppression
better quality of service (QoS), lower bit-error rate (BER)
lower Tx power
MIMO disavantages
• Hardware complexity:
Each antenna needs a radio-frequency (RF) unit
Powerful digital signal processing (DSP) unit required
• Software complexity:
Most signal processing algorithms are computationally intensive
Power consumption:
Battery lifetime of mobile devices
Thermal problems
Antennas:
Antenna spacing (electromagnetic mutual coupling-e.g. mobile handsets)
RF interference and antenna correlation
B)
Most of the present researches on cooperative
network in which the user nodes are equipped with a single
antenna or multiple, there have been some new results which
exploit the benefits of multiple antenna deployment.
Cooperative MIMO technology allows a wireless network
system to attain better performance gains than provided by
either usual MIMO or cooperative systems. It promised
significant improvement in spectral efficiency and network
coverage phenomena for different next generation wireless
communication systems. In wireless communication, the path
towards the various techniques that gives high service quality
and data rate has been through the use of the cooperative
network provided by the rich scattering wireless channels.
Due to their great aspects, MIMO and cooperative systems
have found their way into several standards for future
wireless communication systems, especially in cellular
networks and wireless local area networks (LAN) in this
review article we are presenting the comparative analysis..
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
Index modulation is one of the promising techniques for future communications systems due to many improvement over the classical orthogonal frequency division multiplexing systems such as single RF chain, increased throughput for the same modulation order, achieved tradeoff between the efficiencies of the power and the spectral, and elimination of inter-channel interference. Many forms of index modulation researches exist where symbols are conveyed in antennas, subcarriers, time slots, and the space-time matrix. Spatial modulation is one member of index modulation family where symbols are conveyed in activating transmit/receive antennas. In this paper, a modification to a standard multiple input single output scheme by integrating spatial modulation using simplified mathematical procedure is achieved. In the transmitter side, data and activation symbols are distributed simultaneously using mathematical module and floor functions. At the receiver, a simplified maximum likelihood detector is used to obtain transmitted pair of symbols. To verify this, MATLAB simulink is used to simulate a downlink system where spatial modulation is applied to a base station. Results for different transmit antenna number and modulation order are obtained in the form of bit error rate versus signal to noise ratio.
International Journal of Engineering and Science Invention (IJESI) is an international journal intended for professionals and researchers in all fields of computer science and electronics. IJESI publishes research articles and reviews within the whole field Engineering Science and Technology, new teaching methods, assessment, validation and the impact of new technologies and it will continue to provide information on the latest trends and developments in this ever-expanding subject. The publications of papers are selected through double peer reviewed to ensure originality, relevance, and readability. The articles published in our journal can be accessed online.
Investigating the performance of various channel estimation techniques for mi...ijmnct
This paper simulates and investigates the performance of four widely-used channel estimation techniques for MIMO-OFDM wireless communication systems; namely, super imposed pilot (SIP), comb-type, spacetime block coding (STBC), and space-frequency block coding (SFBC) techniques. The performance is
evaluated through a number of MATLab simulations, where the bit-error rate (BER) and the mean square
error (MSE) are estimated and compared for different levels of signal-to-noise ratio (SNR). The simulation results demonstrate that the comb-type channel estimation and the SIP techniques overwhelmed the performance of the STFC and STBC techniques in terms of both bit-error rate (BER) and mean square error (MSE).
INVESTIGATING THE PERFORMANCE OF VARIOUS CHANNEL ESTIMATION TECHNIQUES FOR MI...ijmnct
This paper simulates and investigates the performance of four widely-used channel estimation techniques for MIMO-OFDM wireless communication systems; namely, super imposed pilot (SIP), comb-type, spacetime block coding (STBC), and space-frequency block coding (SFBC) techniques. The performance is evaluated through a number of MATLab simulations, where the bit-error rate (BER) and the mean square error (MSE) are estimated and compared for different levels of signal-to-noise ratio (SNR). The simulation results demonstrate that the comb-type channel estimation and the SIP techniques overwhelmed the performance of the STFC and STBC techniques in terms of both bit-error rate (BER) and mean square error (MSE).
TECHNIQUES IN PERFORMANCE IMPROVEMENT OF MOBILE WIRELESS COMMUNICATION SYSTEM...Onyebuchi nosiri
Mobile wireless communication providers are expected by their numerous subscribers to provide network that can allow higher data rates, and good voice quality. However, this may be restricted due to some technical problems such as limited availability of radio frequency spectrum, bandwidth, channel capacity, geographical areas and transmission problems caused by various factors like fading and multipath distortion. All these lead to overall system performance degradation. This has led to various studies on how improvement on the performance of wireless communication can be realized using different techniques. This paper is a review of some scholarly works on this subject. To achieve this some recent scholarly articles were accessed online and their findings were highlighted. It was observed that all the articles reviewed had results drawn only from theoretical analysis. Based on this, one of the recommendations is that theoretical analysis should be supported with data obtained from carrying out RF measurements in the field where possible.
TECHNIQUES IN PERFORMANCE IMPROVEMENT OF MOBILE WIRELESS COMMUNICATION SYSTEM...
MIMO OFDM
1. MIMO-OFDM OVERVIEW OF MIMO AND USE OF DIFFERENT TECHNIQUES TO IMPROVE WIRELESS COMMUNICATION USING MIMO By: Darshan Patil, B.E Electronics and Telecommunications, LTCOE