This document provides a literature review of research on bi-metallic plate heat exchangers to enhance convective heat transfer. It discusses 8 studies that experimentally analyzed heat transfer coefficients and pressure drops of different combinations of bi-metallic plates under forced convection. The goal of improving heat transfer efficiency while minimizing pressure losses is important for industries using such heat exchangers like power plants, refrigeration, and chemical processes. The document focuses on reviewing work done to optimize the design of bi-metallic heat exchangers.
FLUID FLOW ANALYSIS IN AIR DUCT FLOW WITH AND WITHOUT INTERNAL THREADS USING ...IAEME Publication
Computational heat transfer flow modeling is one of the great challenges in the classical sciences. As with most problems in engineering, the interest in the heat transfer augmentation is increasing due to its extreme importance in various industrial applications. This paper deals with the analysis of heat transfer for fluid flowing through the pipe with and without internal threads using CFD. Using CFD codes for modeling the heat and fluid flow is an efficient tool for predicting equipment performance. CFD offers a convenient means to study the detailed flows and heat exchange processes, which take place inside the tube. Simulations were carried out using commercial CFD software ANSYS Fluent version 14.5. Friction factor and Nusselt number for air flowing through the specified tube (internal diameter = 0.005 m, length = 0.1 m) were obtained first for the plain tube and then for the tube with internal threads with pitch 5mm in the Reynolds number range of 2000 to 5000. Finally results will be compared to available experimental and analytical calculations. The data obtained by simulation are matching with the literature value for a plain tube with the discrepancy of less than plus or minus 5% for Nusselt number and for the friction factor.
Enhanced heat transfer for the tube with internal threads has been observed. Heat flux is more uniform all along the tube and decreases uniformly towards the center.
experimental investigation of heat transfer intensification of pin fins under...INFOGAIN PUBLICATION
Recent development era in technology has huge requirement of high performance lightweight, and compact heat transfer equipment. To accomplish this demand fins are widely used as effective elements for heat transfer enhancement. One of the commonly used heat exchanger fins is the pin fin which offers an economical and trouble free solution in many situations. This is more important in cooling of air conditioning equipment, thermal power plants, gas turbine blade, aerospace industry, combustion chamber liners, and biomedical devices, electrical and electronic component. Therefore now a day’s industries are utilizing thermal system with pin fins and analyse the various influencing parameters on performance of pin fin of different geometry under force convection. The turbulence occurred due to these techniques are good enough to enhance heat transfer rate. This article is focused on comprehensive review of work carried out in this technology.
In compact heat exchangers, thermal resistance is generally dominant on the air-side and may
account for 80% or more of the total thermal resistance. The air-side heat transfer surface area is 8 to
10 times larger than the water-side. Any improvement in the heat transfer on air-side therefore
improves the overall performance of the heat exchanger. Due to the high thermal resistance on the
air-side, the optimization of such fins is essential to increase the performance of the heat exchangers
which results in thermal systems enhancement. This helps to reduce CO2 emissions through a
reduction of mass and fuel consumption.
Optimization of louvered fin geometry in such heat exchangers is essential to increase the
heat transfer performance and reduce weight, packaging, and cost requirements. In this study deals
with Computational Fluid Dynamics (CFD) studies of the interactions between the air flow and
louvered fins which equipped the automotive heat exchangers is carried out. 3D numerical
simulation results is obtained by using the ANSYS Fluent 14.0 code and compared with
experimental data. Finally the effect of louver angle and louver pitch geometrical parameters, on
overall thermal hydraulic performances of louvered fins is studied.
Experimental Analysis Of Heat Transfer From Square Perforated Fins In Stagger...IJERA Editor
This project gives the experimental analysis of heat transfer over a flat surface equipped with Square perforated
pin fins in staggered arrangement in a rectangular channel. The Fin dimensions are 100mm in height & 25mm in
width. The range of Reynolds number is fixed & about 13,500– 42,000, the clearance ratio (C/H) 0, 0.33 and 1,
the inter-fin spacing ratio (Sy /D) 1.208, 1.524, 1.944 and 3.417. Sy i.e. stream wise distance is varies and Sx i.e.
span wise distance is constant. The friction factor, enhancement efficiency and heat transfer correlate in
equations with each other. Here we are comparing Square pin fins with cylindrical pin fins. Staggered
arrangement and perforation will enhance the heat transfer rate. Clearance ratio and inter-fin spacing ratio affect
on Enhancement efficiency. Both lower clearance ratio and lower inter-fin spacing ratio and comparatively lower
Reynolds number give higher thermal performance. Friction factor & Nusselt number are Key parameter which
relates with efficiency enhancement and heat transfer rate.
Analysis of Coiled-Tube Heat Exchangers to Improve Heat Transfer Rate With Sp...IJMER
Steady heat transfer enhancement has been studied in helically coiled-tube heat exchangers. The outer side of the wall of the heat exchanger contains a helical corrugation which makes a helical rib on the inner side of the tube wall to induce additional swirling motion of fluid particles. Numerical calculations have been carried out to examine different geometrical parameters and the impact of flow and thermal boundary conditions for the heat transfer rate in laminar and transitional flow regimes. Calculated results have been compared to existing empirical formula and experimental tests to investigate the validity of the numerical results in case of common helical tube heat exchanger and additionally results of the numerical computation of corrugated straight tubes for laminar and transition flow have been validated with experimental tests available in the literature. Comparison of the flow and temperature fields in case of common helical tube and the coil with spirally corrugated wall configuration are discussed. Heat exchanger coils with helically corrugated wall configuration show 80–100% increase for the inner side heat transfer rate due to the additionally developed swirling motion while the relative pressure drop is 10–600% larger compared to the common helically coiled heat exchangers. New empirical Co-relation has been proposed for the fully developed inner side heat transfer prediction in case of helically corrugated wall configuration.
FLUID FLOW ANALYSIS IN AIR DUCT FLOW WITH AND WITHOUT INTERNAL THREADS USING ...IAEME Publication
Computational heat transfer flow modeling is one of the great challenges in the classical sciences. As with most problems in engineering, the interest in the heat transfer augmentation is increasing due to its extreme importance in various industrial applications. This paper deals with the analysis of heat transfer for fluid flowing through the pipe with and without internal threads using CFD. Using CFD codes for modeling the heat and fluid flow is an efficient tool for predicting equipment performance. CFD offers a convenient means to study the detailed flows and heat exchange processes, which take place inside the tube. Simulations were carried out using commercial CFD software ANSYS Fluent version 14.5. Friction factor and Nusselt number for air flowing through the specified tube (internal diameter = 0.005 m, length = 0.1 m) were obtained first for the plain tube and then for the tube with internal threads with pitch 5mm in the Reynolds number range of 2000 to 5000. Finally results will be compared to available experimental and analytical calculations. The data obtained by simulation are matching with the literature value for a plain tube with the discrepancy of less than plus or minus 5% for Nusselt number and for the friction factor.
Enhanced heat transfer for the tube with internal threads has been observed. Heat flux is more uniform all along the tube and decreases uniformly towards the center.
experimental investigation of heat transfer intensification of pin fins under...INFOGAIN PUBLICATION
Recent development era in technology has huge requirement of high performance lightweight, and compact heat transfer equipment. To accomplish this demand fins are widely used as effective elements for heat transfer enhancement. One of the commonly used heat exchanger fins is the pin fin which offers an economical and trouble free solution in many situations. This is more important in cooling of air conditioning equipment, thermal power plants, gas turbine blade, aerospace industry, combustion chamber liners, and biomedical devices, electrical and electronic component. Therefore now a day’s industries are utilizing thermal system with pin fins and analyse the various influencing parameters on performance of pin fin of different geometry under force convection. The turbulence occurred due to these techniques are good enough to enhance heat transfer rate. This article is focused on comprehensive review of work carried out in this technology.
In compact heat exchangers, thermal resistance is generally dominant on the air-side and may
account for 80% or more of the total thermal resistance. The air-side heat transfer surface area is 8 to
10 times larger than the water-side. Any improvement in the heat transfer on air-side therefore
improves the overall performance of the heat exchanger. Due to the high thermal resistance on the
air-side, the optimization of such fins is essential to increase the performance of the heat exchangers
which results in thermal systems enhancement. This helps to reduce CO2 emissions through a
reduction of mass and fuel consumption.
Optimization of louvered fin geometry in such heat exchangers is essential to increase the
heat transfer performance and reduce weight, packaging, and cost requirements. In this study deals
with Computational Fluid Dynamics (CFD) studies of the interactions between the air flow and
louvered fins which equipped the automotive heat exchangers is carried out. 3D numerical
simulation results is obtained by using the ANSYS Fluent 14.0 code and compared with
experimental data. Finally the effect of louver angle and louver pitch geometrical parameters, on
overall thermal hydraulic performances of louvered fins is studied.
Experimental Analysis Of Heat Transfer From Square Perforated Fins In Stagger...IJERA Editor
This project gives the experimental analysis of heat transfer over a flat surface equipped with Square perforated
pin fins in staggered arrangement in a rectangular channel. The Fin dimensions are 100mm in height & 25mm in
width. The range of Reynolds number is fixed & about 13,500– 42,000, the clearance ratio (C/H) 0, 0.33 and 1,
the inter-fin spacing ratio (Sy /D) 1.208, 1.524, 1.944 and 3.417. Sy i.e. stream wise distance is varies and Sx i.e.
span wise distance is constant. The friction factor, enhancement efficiency and heat transfer correlate in
equations with each other. Here we are comparing Square pin fins with cylindrical pin fins. Staggered
arrangement and perforation will enhance the heat transfer rate. Clearance ratio and inter-fin spacing ratio affect
on Enhancement efficiency. Both lower clearance ratio and lower inter-fin spacing ratio and comparatively lower
Reynolds number give higher thermal performance. Friction factor & Nusselt number are Key parameter which
relates with efficiency enhancement and heat transfer rate.
Analysis of Coiled-Tube Heat Exchangers to Improve Heat Transfer Rate With Sp...IJMER
Steady heat transfer enhancement has been studied in helically coiled-tube heat exchangers. The outer side of the wall of the heat exchanger contains a helical corrugation which makes a helical rib on the inner side of the tube wall to induce additional swirling motion of fluid particles. Numerical calculations have been carried out to examine different geometrical parameters and the impact of flow and thermal boundary conditions for the heat transfer rate in laminar and transitional flow regimes. Calculated results have been compared to existing empirical formula and experimental tests to investigate the validity of the numerical results in case of common helical tube heat exchanger and additionally results of the numerical computation of corrugated straight tubes for laminar and transition flow have been validated with experimental tests available in the literature. Comparison of the flow and temperature fields in case of common helical tube and the coil with spirally corrugated wall configuration are discussed. Heat exchanger coils with helically corrugated wall configuration show 80–100% increase for the inner side heat transfer rate due to the additionally developed swirling motion while the relative pressure drop is 10–600% larger compared to the common helically coiled heat exchangers. New empirical Co-relation has been proposed for the fully developed inner side heat transfer prediction in case of helically corrugated wall configuration.
Research Inventy : International Journal of Engineering and Science is published by the group of young academic and industrial researchers with 12 Issues per year. It is an online as well as print version open access journal that provides rapid publication (monthly) of articles in all areas of the subject such as: civil, mechanical, chemical, electronic and computer engineering as well as production and information technology. The Journal welcomes the submission of manuscripts that meet the general criteria of significance and scientific excellence. Papers will be published by rapid process within 20 days after acceptance and peer review process takes only 7 days. All articles published in Research Inventy will be peer-reviewed.
Comparative Study and Analysis between Helical Coil and Straight Tube Heat Ex...IJERA Editor
The purpose of this study is to determine the relative advantage of using a helically coiled heat exchanger against a straight tube heat exchanger. It is found that the heat transfer in helical circular tubes is higher as compared to Straight tube due to their shape. Helical coils offer advantageous over straight tubes due to their compactness and increased heat transfer coefficient. The increased heat transfer coefficients are a consequence of the curvature of the coil, which induces centrifugal forces to act on the moving fluid, resulting in the development of secondary flow. The curvature of the coil governs the centrifugal force while the pitch (or helix angle) influences the torsion to which the fluid is subjected to the centrifugal force results in the development of secondary flow. Due to the curvature effect, the fluid streams in the outer side of the pipe moves faster than the fluid streams in the inner side of the pipe. In current work the fluid to fluid heat exchange is taken into consideration. Most of the investigations on heat transfer coefficients are for constant wall temperature or constant heat flux. The effectiveness, overall heat transfer coefficient, effect of cold water flow rate on effectiveness of heat exchanger when hot water mass flow rate is kept constant and effect of hot water flow rate on effectiveness when cold water flow rate kept constant studied and compared for parallel flow, counter flow arrangement of Helical coil and Straight tube heat exchangers. All readings were taken at steady state condition of heat exchanger. The result shows that the heat transfer coefficient is affected by the geometry of the heat exchanger. Helical coil heat exchanger are superior in all aspect studied here.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
CFD Analysis of Concentric Tube Heat Exchanger Using Twisted TapesIJARIIT
In this paper, the three dimensional CFD modeling studies on heat transfer, friction factor and thermal performance
of concentric tube heat exchanger using twisted tapes (Plain, V-cut, , Jagged V-cut) with different twist ratios (y=2.0, 4.0) are
used. Twisted tapes are used to augment the heat transfer by creating turbulence in the fluid flow. Various methods are applied
to increase thermal performance of heat transfer devices such as treated surfaces, rough surfaces, swirling flow devices, coiled
tubes, and surface tension devices. Out of these twisted tape method is used to increase the thermal performance. Twisted tape
inserts on effectiveness of heat exchanger has analyzed for different Reynolds Number. The maximum thermal performance
factor was obtained by the Jagged V-cut twisted tape (H=50) insert compare to other twisted tapes. Simultaneously the friction
factor has been analyzed
Experimental Study of Heat Transfer Enhancement of Pipe-inPipe Helical Coil H...iosrjce
Heat transfer enhancement in pipe in pipe helical coils has been research by many researchers.
While the many literatures available on heat transfer characteristics of helical coil heat exchangers. There is
very few published on validate experimental results through Computational Fluid Dynamics. This paper focuses
on experimental investigation of fluid-to-fluid heat transfer enhancement of pipe-in-pipe helical coil tubes. The
methodology of experimental analysis of a helical tubes heat exchanger, the effect of the inside tubes at constant
value of mass flow rate in Dean Number and also established the surface heat transfer coefficient. Heat transfer
characteristics inside pipe-in-pipe helical coils for various boundary conditions, that the specification of a
constant temperature at hot water inlet, constant mass flow rate. Hence, the pipe-in-pipe heat exchanger is
considering different mass flow rate inside and annulus. The fabrication of experimental setup is estimate the
heat transfer enhancement in inside helical coil tubes
A Review on Study of Heat Transfer Analysis of Helical Coil Heat Exchangersijtsrd
Now a day’s a geometrically modified Helical coil heat exchangers are widely using in industrial applications like cryogenic state processes, air conditioning, thermal nuclear reactors and waste heat recovery due to their compact size and high heat transfer coefficient. Advantage of using helical coils over straight tubes is that the residence time spread is reduced, allowing helical coils to be used to reduce axial dispersion in tubular reactors. In this study, numerical investigation of the influence of geometrical parameters such as tube diameter d , coil radius R , and coil pitch p on overall heat transfer coefficient in helical double tube heat exchangers are performed using a professional CFD software FLUENT. In recent years, numerous styles were introduced for heat exchangers that apply to completely different applications sadly, their heat transfer co efficient wasnt reliable at different operational conditions. the standard of the heat changed rate wasnt optimized and there have been many deficiencies and errors in styles. The heat transfer of the copper material is enhanced in comparison with other material unfortunately thermal resistance is reduced with an increase in pressure drop thus enhancing the heat transfer on the heat exchanger. Helical architecture is often designed with a clear motive of compact size and also address heat transfer co efficient and other ancillary attributes efficiently and effectively. So the better material is suggested for an industrial heat exchanger according to the applications is Copper with the basis of simulation results. The geometry and different dimension parameter of the helical coil show that the proposed study in different material properties and different mass flow rates to heat transfer are maximum in different parameter helical coil heat exchangers. Finally, the heat transfer increase for the copper material compared to another material but with the increase in pressure drop the corresponding thermal resistance decreases which allow the improved heat transfer rate and the rate increases from Aluminum to Bronze to Copper. With the drop in temperature, the thermal resistance is reduced which enhances the heat transfer rate. The simulation results show that the copper has a high heat transfer coefficient than Aluminum and Bronze while operating in identical conditions. Due to the extensive use of helical coils in various applications, knowledge about the flow patterns and heat transfer characteristics are important. Atul Vats | Sunil Kumar Chaturvedi | Abhishek Bhandari "A Review on Study of Heat Transfer Analysis of Helical Coil Heat Exchangers" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-5 | Issue-4 , June 2021, URL: https://www.ijtsrd.compapers/ijtsrd43650.pdf Paper URL: https://www.ijtsrd.comengineering/mechanical-engineering/43650/a-review-on-study-of-heat-transfer-analysis-of-helical-coil-heat-exchangers/atul-vats
Analysis of Natural Convention Heat Transfer Enhancement in Finned Tube Heat ...journal ijrtem
ABSTRACT: Most of the engineering problems require high performance heat transfer components with progressively less weight, volumes, accommodating shapes and costs. Air cooled heat exchangers are subjected to air on outer side of heat exchanger surface on in heat recovery systems like economizers gases are subjected on one side of tube surface. On air or gas side heat transfer coefficient is less. Extended surface (fins) are one of the next exchanging devices that are employed extensively to increase heat transfer rates from tubular heat exchangers. The rate of heat transfer depends on the surface area of fin available for exchanging the heat transfer rate from the primary surface of cylindrical shape. Present study focuses on enhancement of heat transfer by using both circular and elliptical type of fins. The present paper attempts to examine trend of heat transfer coefficient experimentally and by using CFD software for various types of elliptical fins with i) varying elliptical ratio, ii) changing orientation of mounting of heat exchanger tube with elliptical fins, iii) varying spacing or fin density. KEY WORDS: Natural convection, Heat transfer enhancements, Elliptical fin, Fin orientation, Fin density.
Research Inventy : International Journal of Engineering and Science is published by the group of young academic and industrial researchers with 12 Issues per year. It is an online as well as print version open access journal that provides rapid publication (monthly) of articles in all areas of the subject such as: civil, mechanical, chemical, electronic and computer engineering as well as production and information technology. The Journal welcomes the submission of manuscripts that meet the general criteria of significance and scientific excellence. Papers will be published by rapid process within 20 days after acceptance and peer review process takes only 7 days. All articles published in Research Inventy will be peer-reviewed.
Comparative Study and Analysis between Helical Coil and Straight Tube Heat Ex...IJERA Editor
The purpose of this study is to determine the relative advantage of using a helically coiled heat exchanger against a straight tube heat exchanger. It is found that the heat transfer in helical circular tubes is higher as compared to Straight tube due to their shape. Helical coils offer advantageous over straight tubes due to their compactness and increased heat transfer coefficient. The increased heat transfer coefficients are a consequence of the curvature of the coil, which induces centrifugal forces to act on the moving fluid, resulting in the development of secondary flow. The curvature of the coil governs the centrifugal force while the pitch (or helix angle) influences the torsion to which the fluid is subjected to the centrifugal force results in the development of secondary flow. Due to the curvature effect, the fluid streams in the outer side of the pipe moves faster than the fluid streams in the inner side of the pipe. In current work the fluid to fluid heat exchange is taken into consideration. Most of the investigations on heat transfer coefficients are for constant wall temperature or constant heat flux. The effectiveness, overall heat transfer coefficient, effect of cold water flow rate on effectiveness of heat exchanger when hot water mass flow rate is kept constant and effect of hot water flow rate on effectiveness when cold water flow rate kept constant studied and compared for parallel flow, counter flow arrangement of Helical coil and Straight tube heat exchangers. All readings were taken at steady state condition of heat exchanger. The result shows that the heat transfer coefficient is affected by the geometry of the heat exchanger. Helical coil heat exchanger are superior in all aspect studied here.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
CFD Analysis of Concentric Tube Heat Exchanger Using Twisted TapesIJARIIT
In this paper, the three dimensional CFD modeling studies on heat transfer, friction factor and thermal performance
of concentric tube heat exchanger using twisted tapes (Plain, V-cut, , Jagged V-cut) with different twist ratios (y=2.0, 4.0) are
used. Twisted tapes are used to augment the heat transfer by creating turbulence in the fluid flow. Various methods are applied
to increase thermal performance of heat transfer devices such as treated surfaces, rough surfaces, swirling flow devices, coiled
tubes, and surface tension devices. Out of these twisted tape method is used to increase the thermal performance. Twisted tape
inserts on effectiveness of heat exchanger has analyzed for different Reynolds Number. The maximum thermal performance
factor was obtained by the Jagged V-cut twisted tape (H=50) insert compare to other twisted tapes. Simultaneously the friction
factor has been analyzed
Experimental Study of Heat Transfer Enhancement of Pipe-inPipe Helical Coil H...iosrjce
Heat transfer enhancement in pipe in pipe helical coils has been research by many researchers.
While the many literatures available on heat transfer characteristics of helical coil heat exchangers. There is
very few published on validate experimental results through Computational Fluid Dynamics. This paper focuses
on experimental investigation of fluid-to-fluid heat transfer enhancement of pipe-in-pipe helical coil tubes. The
methodology of experimental analysis of a helical tubes heat exchanger, the effect of the inside tubes at constant
value of mass flow rate in Dean Number and also established the surface heat transfer coefficient. Heat transfer
characteristics inside pipe-in-pipe helical coils for various boundary conditions, that the specification of a
constant temperature at hot water inlet, constant mass flow rate. Hence, the pipe-in-pipe heat exchanger is
considering different mass flow rate inside and annulus. The fabrication of experimental setup is estimate the
heat transfer enhancement in inside helical coil tubes
A Review on Study of Heat Transfer Analysis of Helical Coil Heat Exchangersijtsrd
Now a day’s a geometrically modified Helical coil heat exchangers are widely using in industrial applications like cryogenic state processes, air conditioning, thermal nuclear reactors and waste heat recovery due to their compact size and high heat transfer coefficient. Advantage of using helical coils over straight tubes is that the residence time spread is reduced, allowing helical coils to be used to reduce axial dispersion in tubular reactors. In this study, numerical investigation of the influence of geometrical parameters such as tube diameter d , coil radius R , and coil pitch p on overall heat transfer coefficient in helical double tube heat exchangers are performed using a professional CFD software FLUENT. In recent years, numerous styles were introduced for heat exchangers that apply to completely different applications sadly, their heat transfer co efficient wasnt reliable at different operational conditions. the standard of the heat changed rate wasnt optimized and there have been many deficiencies and errors in styles. The heat transfer of the copper material is enhanced in comparison with other material unfortunately thermal resistance is reduced with an increase in pressure drop thus enhancing the heat transfer on the heat exchanger. Helical architecture is often designed with a clear motive of compact size and also address heat transfer co efficient and other ancillary attributes efficiently and effectively. So the better material is suggested for an industrial heat exchanger according to the applications is Copper with the basis of simulation results. The geometry and different dimension parameter of the helical coil show that the proposed study in different material properties and different mass flow rates to heat transfer are maximum in different parameter helical coil heat exchangers. Finally, the heat transfer increase for the copper material compared to another material but with the increase in pressure drop the corresponding thermal resistance decreases which allow the improved heat transfer rate and the rate increases from Aluminum to Bronze to Copper. With the drop in temperature, the thermal resistance is reduced which enhances the heat transfer rate. The simulation results show that the copper has a high heat transfer coefficient than Aluminum and Bronze while operating in identical conditions. Due to the extensive use of helical coils in various applications, knowledge about the flow patterns and heat transfer characteristics are important. Atul Vats | Sunil Kumar Chaturvedi | Abhishek Bhandari "A Review on Study of Heat Transfer Analysis of Helical Coil Heat Exchangers" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-5 | Issue-4 , June 2021, URL: https://www.ijtsrd.compapers/ijtsrd43650.pdf Paper URL: https://www.ijtsrd.comengineering/mechanical-engineering/43650/a-review-on-study-of-heat-transfer-analysis-of-helical-coil-heat-exchangers/atul-vats
Analysis of Natural Convention Heat Transfer Enhancement in Finned Tube Heat ...journal ijrtem
ABSTRACT: Most of the engineering problems require high performance heat transfer components with progressively less weight, volumes, accommodating shapes and costs. Air cooled heat exchangers are subjected to air on outer side of heat exchanger surface on in heat recovery systems like economizers gases are subjected on one side of tube surface. On air or gas side heat transfer coefficient is less. Extended surface (fins) are one of the next exchanging devices that are employed extensively to increase heat transfer rates from tubular heat exchangers. The rate of heat transfer depends on the surface area of fin available for exchanging the heat transfer rate from the primary surface of cylindrical shape. Present study focuses on enhancement of heat transfer by using both circular and elliptical type of fins. The present paper attempts to examine trend of heat transfer coefficient experimentally and by using CFD software for various types of elliptical fins with i) varying elliptical ratio, ii) changing orientation of mounting of heat exchanger tube with elliptical fins, iii) varying spacing or fin density. KEY WORDS: Natural convection, Heat transfer enhancements, Elliptical fin, Fin orientation, Fin density.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
A Detailed Review on Artificial Roughness Geometries for Optimizing Thermo-Hy...IJMER
It is well known fact that the heat transfer coefficient between the absorber surface of solar air collector & flowing fluid i.e. air can be improved by providing artificial roughness geometry on heat transfer surface (absorber surface).In this way the Thermal efficiency is increased. But at the same time due to roughness geometry pumping power of solar air collector in increased due to fictional losses in duct. So it necessary to examine the shape, size & flow pattern of various roughness elements to get maximum efficiency with minimum frictional losses. Therefore the selection of roughness geometry has to be based on the parameter that takes into account both Thermal & Hydraulic (friction) performance i.e. Thermo-hydraulic Performance of Solar air collector. Number of roughness elements has been investigated on heat transfer & friction characteristics of solar air collectors. In this paper, reviews of various artificial roughness elements used as passive heat transfer techniques, in order to improve Thermo-hydraulic performance of solar air collectors is reviewed & presented. Correlations developed by various researchers with the help of experimental results for heat transfer & friction factor for solar air collector by taking different roughness geometries are given & these correlations are useful to predict the Thermo-hydraulic performance of solar air collector having roughened ducts. The objective of this paper is also the awareness of effect of various types’ roughness geometries on heat
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
CFD Analysis of Plate Fin Tube Heat Exchanger for Various Fin InclinationsIJERA Editor
ANSYS Fluent software is used for three dimensional CFD simulations to investigate heat transfer and fluid flow characteristics of six different fin angles with plain fin tube heat exchangers. The numerical simulation of the fin tube heat exchanger was performed by using a three dimensional numerical computation technique. Geometry of model is created and meshed by using ANSYS Workbench software. To solve the equation for the fluid flow and heat transfer analysis ANSYS FLUENT was used in the fin-tube heat exchanger. The fluid flow and heat transfer are simulated and result compared for both laminar and turbulent flow models k-epsilon and SST k-omega, with steady state solvers to calculate heat transfer, flow velocity and temperature fields of variable inclined fin angles (Ɵ = 00,100 , 200, 300, 400,500). Model is validate by comparing the simulated value of velocity, temperature and colburn factor with experimental and numerical results investigated by WANG [1] and GHORI KIRAR [10]. Reasonable agreement is found between the simulations and other results, and the ANSYS Fluent software is sufficient for simulating the flow fields in tube fin heat exchanger.
EXPERIMENTAL STUDY OF HEAT TRANSFER FROM PLATE FIN ARRAY IN MIXED CONVECTION ...ijiert bestjournal
The work summarized in this paper presents an exper imental study of heat transfer from plate fin in mixed convection mode enhancement by the us e of plate fins is presented. After a brief review of the basic methods used to enhance the hea t transfer by simultaneous increase of heat transfer surface area as well as the heat tran sfer coefficient,a simple experimental method to assess the heat transfer enhancement is p resented. The method is demonstrated on plate fins as elements for the heat transfer enhanc ement,but it can in principle be applied also to other fin forms. That is varying various paramet ers (height,spacing). The order of the magnitude of heat transfer enhancement obtained exp erimentally,it was found that by a direct comparison of Nu and Re no conclusion regarding the relative performances could be made. This is because the dimensionless variables are int roduced for the scaling of heat transfer and pressure drop results from laboratory to large scal e but not for the performance comparison. Therefore a literature survey of the performance co mparison methods used in the past was also performed. Experiments will carried out on mix ed convection heat transfer from plate fin heat sinks subject to the influence of its geometry and heat flux. A total of 9 plate fins were pasted into the upper surface of the base plate. Th e area of the base plate is 150mm by 150mm. The base plate and the fins were made of alu minum. For all tested plate fin heat sinks,however,the heat transfer performance for h eat sinks with plate fins was better than that of solid pins.
Biodiesel, Brake thermal efficiency, Brake specific fuel consumption Honge, J...IJMER
Steady heat transfer enhancement has been studied in helically coiled-tube heat exchangers. The outer side of the wall of the heat exchanger contains a helical corrugation which makes a helical rib on the inner side of the tube wall to induce additional swirling motion of fluid particles. Numerical calculations have been carried out to examine different geometrical parameters and the impact of flow and thermal boundary conditions for the heat transfer rate in laminar and transitional flow regimes. Calculated results have been compared to existing empirical formula and experimental tests to investigate the validity of the numerical results in case of common helical tube heat exchanger and additionally results of the numerical computation of corrugated straight tubes for laminar and transition flow have been validated with experimental tests available in the literature. Comparison of the flow and temperature fields in case of common helical tube and the coil with spirally corrugated wall configuration are discussed. Heat exchanger coils with helically corrugated wall configuration show 80–100% increase for the inner side heat transfer rate due to the additionally developed swirling motion while the relative pressure drop is 10–600% larger compared to the common helically coiled heat exchangers. New empirical Co-relation has been proposed for the fully developed inner side heat transfer prediction in case of helically corrugated wall configuration.
HEAT TRANSFER AUGMENTATION IN A PLATE-FIN HEAT EXCHANGER: A REVIEWIAEME Publication
The improvement of the performance of heat exchangers with gas as the working fluid becomes particularly important due to the high thermal resistance offered by gases in general. In order to compensate for the poor heat transfer properties of gases, the surface area density of plate heat exchangers can be increased by making use of the secondary fins such as, off-set fins, triangular fins, wavy fins, louvered fins etc. In addition, a promising technique for the enhancement of heat transfer is the use of longitudinal vortex generators. The longitudinal vortices are produced due to the pressure difference generated between the front and back surface of the vortex generator.
About
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.
Technical Specifications
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
Key Features
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface
• Compatible with MAFI CCR system
• Copatiable with IDM8000 CCR
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
Application
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.
Student information management system project report ii.pdfKamal Acharya
Our project explains about the student management. This project mainly explains the various actions related to student details. This project shows some ease in adding, editing and deleting the student details. It also provides a less time consuming process for viewing, adding, editing and deleting the marks of the students.
Overview of the fundamental roles in Hydropower generation and the components involved in wider Electrical Engineering.
This paper presents the design and construction of hydroelectric dams from the hydrologist’s survey of the valley before construction, all aspects and involved disciplines, fluid dynamics, structural engineering, generation and mains frequency regulation to the very transmission of power through the network in the United Kingdom.
Author: Robbie Edward Sayers
Collaborators and co editors: Charlie Sims and Connor Healey.
(C) 2024 Robbie E. Sayers
Explore the innovative world of trenchless pipe repair with our comprehensive guide, "The Benefits and Techniques of Trenchless Pipe Repair." This document delves into the modern methods of repairing underground pipes without the need for extensive excavation, highlighting the numerous advantages and the latest techniques used in the industry.
Learn about the cost savings, reduced environmental impact, and minimal disruption associated with trenchless technology. Discover detailed explanations of popular techniques such as pipe bursting, cured-in-place pipe (CIPP) lining, and directional drilling. Understand how these methods can be applied to various types of infrastructure, from residential plumbing to large-scale municipal systems.
Ideal for homeowners, contractors, engineers, and anyone interested in modern plumbing solutions, this guide provides valuable insights into why trenchless pipe repair is becoming the preferred choice for pipe rehabilitation. Stay informed about the latest advancements and best practices in the field.
Welcome to WIPAC Monthly the magazine brought to you by the LinkedIn Group Water Industry Process Automation & Control.
In this month's edition, along with this month's industry news to celebrate the 13 years since the group was created we have articles including
A case study of the used of Advanced Process Control at the Wastewater Treatment works at Lleida in Spain
A look back on an article on smart wastewater networks in order to see how the industry has measured up in the interim around the adoption of Digital Transformation in the Water Industry.
NO1 Uk best vashikaran specialist in delhi vashikaran baba near me online vas...Amil Baba Dawood bangali
Contact with Dawood Bhai Just call on +92322-6382012 and we'll help you. We'll solve all your problems within 12 to 24 hours and with 101% guarantee and with astrology systematic. If you want to take any personal or professional advice then also you can call us on +92322-6382012 , ONLINE LOVE PROBLEM & Other all types of Daily Life Problem's.Then CALL or WHATSAPP us on +92322-6382012 and Get all these problems solutions here by Amil Baba DAWOOD BANGALI
#vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore#blackmagicformarriage #aamilbaba #kalajadu #kalailam #taweez #wazifaexpert #jadumantar #vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore #blackmagicforlove #blackmagicformarriage #aamilbaba #kalajadu #kalailam #taweez #wazifaexpert #jadumantar #vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore #Amilbabainuk #amilbabainspain #amilbabaindubai #Amilbabainnorway #amilbabainkrachi #amilbabainlahore #amilbabaingujranwalan #amilbabainislamabad
CFD Simulation of By-pass Flow in a HRSG module by R&R Consult.pptxR&R Consult
CFD analysis is incredibly effective at solving mysteries and improving the performance of complex systems!
Here's a great example: At a large natural gas-fired power plant, where they use waste heat to generate steam and energy, they were puzzled that their boiler wasn't producing as much steam as expected.
R&R and Tetra Engineering Group Inc. were asked to solve the issue with reduced steam production.
An inspection had shown that a significant amount of hot flue gas was bypassing the boiler tubes, where the heat was supposed to be transferred.
R&R Consult conducted a CFD analysis, which revealed that 6.3% of the flue gas was bypassing the boiler tubes without transferring heat. The analysis also showed that the flue gas was instead being directed along the sides of the boiler and between the modules that were supposed to capture the heat. This was the cause of the reduced performance.
Based on our results, Tetra Engineering installed covering plates to reduce the bypass flow. This improved the boiler's performance and increased electricity production.
It is always satisfying when we can help solve complex challenges like this. Do your systems also need a check-up or optimization? Give us a call!
Work done in cooperation with James Malloy and David Moelling from Tetra Engineering.
More examples of our work https://www.r-r-consult.dk/en/cases-en/