How to Use the GBHE Mixing Guides
0 INTRODUCTION/PURPOSE
1 SCOPE
2 FIELD OF APPLICATION
3 DEFINITIONS
4 THE MIXING GUIDES
4.1 Mixing Guides
4.2 GBHE Mixing and Agitation Manual
5 DEVICE SELECTION
6 MIXING QUESTIONNAIRE
6.1 What is being mixed?
6.2 Why is it being mixed?
6.3 How is it to be mixed?
6.4 Is Heat Transfer Important?
6.5 Is Mixing Time Important?
6.6 Is Inventory Important?
6.7 Is Subsequent Phase Separation Important?
6.8 What Quantities?
6.9 What are the Selection Criteria?
6.10 What Data are required?
7 BASICS
7.1 Bulk Movement
7.2 Shear and Elongation
7.3 Turbulent Diffusion
7.4 Molecular Diffusion
7.5 Mixing Mechanisms
APPENDICES
A ROTATING MIXING DEVICES
B MIXING DEVICES WITHOUT MOVING PARTS
How to use the GBHE Reactor Technology Guides
0 INTRODUCTION / PURPOSE
1 SCOPE
2 FIELD OF APPLICATION
3 DEFINITIONS
4 BACKGROUND
5 THE DECISION TREE
6 GBHE REACTION ENGINEERING
7 GENERAL ASPECTS OF REACTOR TECHNOLOGY
7.1 Criteria of Reactor Performance
7.2 Factors of Economic Importance
7.3 Physicochemical Mechanisms
8 GENERAL GUIDE TO SELECTION OF REACTOR TYPE AND OPERATION
8.1 Choice of Reactor Type
8.2 Reaction Mechanism and Kinetics
8.3 Thermodynamics
8.4 Other Factors
9 GENERAL REFERENCES AND SOURCES OF
INFORMATION
APPENDICES
A RELATIONSHIP BEWTEEN DEFINED TERMS
FIGURES
1 DECISION TREE
2 RELATIVE YIELDS OF B FOR BATCH (OR PLUG FLOW) AND CST REACTORS
3 REACTOR SURVEY FORM
Heating and Cooling of Batch Processes
0 INTRODUCTION/PURPOSE
1 SCOPE
2 FIELD OF APPLICATION
3 DEFINITIONS
3.1 units
4 STATEMENT OF THE PROBLEM
5 DEVELOPMENT OF THE METHOD
5.1 Assumptions
5.2 Basic Equations
6 APPLICATION OF THE METHOD
6.1 Determining the Behavior of an Existing System
6.2 Specifying the Heat Transfer Duty for a New System
APPENDICES
A DERIVATION OF THE EQUATIONS
B WORKED EXAMPLES
FIGURES
1 CASES CONSIDERED
Reactor and Catalyst Design
0 INTRODUCTION/PURPOSE
1 SCOPE
2 FIELD OF APPLICATION
3 DEFINITIONS
4 CATALYST DESIGN
4.1 Equivalent Pellet Diameter
4.2 Voidage
4.3 Pellet Density
5 REACTOR DESIGN
6 CATALYST SUPPORT
6.1 Choice of Support
TABLES
1 CATALYST SUPPORT SHAPES
2 SECONDARY REFORMER SPREADSHEET
FIGURES
1 GRAPH OF EFFECTIVENESS v THIELE MODULUS
2 VARIATION OF COSTS WITH CATALYST SIZE
3 VARIATION OF COSTS WITH CATALYST BED VOIDAGE
4 VARIATION OF COSTS WITH VESSEL DIAMETER
SMR PRE-REFORMER DESIGN
Case Study #0618416GB/H
Contents
1. SMR Pre-Reformer Design
2. Inlet Baffle Design
3. Outlet Collector
4. Hold Down Grating
5. Floating Hold Down Screen
6. Catalyst Drop Out Nozzle
7. Thermowell Detail
8. Technical Performance requirements
9. SMR Pre-Reformer Isolation
Technical Review and Commentary on Proposed Design
APPENDIX
A. Operating / Mechanical Data
B. Materials Specifications
C. Fabrication and Inspection Requirements
D. Weights
E. Nozzle Data
F. Instrument Connections
G. Manholes
Design and Simulation of Continuous Distillation ColumnsGerard B. Hawkins
Design and Simulation of Continuous Distillation Columns
0 INTRODUCTION/PURPOSE
1 SCOPE
2 FIELD OF APPLICATION
3 DEFINITIONS
4 FRACTIONAL DISTILLATION
5 ROUGH METHOD OF COLUMN DESIGN
5.1 Sharp Separations
5.2 Sloppy Separations
6 DETAIL DESIGN USING THE CHEMCAD DISTILLATION PROGRAM
6.1 Sharp Separations
6.2 Sloppy Separations
7 COMPLEX COLUMNS
7.1 Multiple Feeds
7.2 Sidestream Take-Offs
8 DESIGN USING A LABORATORY COLUMN
SIMULATION
9 DESIGN USING ACTUAL PLANT DATA
9.1 Uprating or Debottlenecking Exercises
10 REFERENCES
APPENDICES
A WORKED EXAMPLE
B SLOPPY SEPARATIONS
C SIMULATION USING PLANT DATA : CASE HISTORIES
TABLES
Getting the Most Out of Your Refinery Hydrogen PlantGerard B. Hawkins
Getting the Most Out of Your Refinery Hydrogen Plant
Contents
Summary
1 Introduction
2 "On-purpose" Hydrogen Production
3 Operational Aspects
4 Uprating Options on the Steam Reformer
4.1 Steam Reforming Catalysts and Tube Metallurgy
4.2 Oxygen-blown Secondary Reformer
4.3 Pre-reforming
4.4 Post-reforming
5 Downstream Units
6 Summary of Uprating Options
7 Conclusions
The Design and Layout of Vertical Thermosyphon ReboilersGerard B. Hawkins
The Design and Layout of Vertical Thermosyphon Reboilers
0 INTRODUCTION/PURPOSE
1 SCOPE
2 FIELD OF APPLICATION
3 DEFINITIONS
4 THE DESIGN PROBLEM
5 COMPUTER PROGRAMS
6 GENERAL CONSIDERATIONS
6.1 Heating Medium Temperature
6.2 Fouling Resistance
7 DESIGN PARAMETERS
7.1 Overall Arrangement and Specifications
7.2 Geometry Elements
8 ANALYSIS OF COMMERCIALLY AVAILABLE
PROGRAM RESULTS
8.1 Main Results
8.2 Supplementary Results
8.3 Error Analysis
8.4 Adjustments to Design
9 OPERATING RANGE
10 CONTROL
10.1 Control of Condensing Heating Medium Pressure
10.2 Control of The Condensate Level
10.3 Control of Sensible Fluid Flow Rate
11 LAYOUT
11.1 Factors Influencing Design
11.2 A Standard Layout
12 BIBLIOGRAPHY
How to use the GBHE Reactor Technology Guides
0 INTRODUCTION / PURPOSE
1 SCOPE
2 FIELD OF APPLICATION
3 DEFINITIONS
4 BACKGROUND
5 THE DECISION TREE
6 GBHE REACTION ENGINEERING
7 GENERAL ASPECTS OF REACTOR TECHNOLOGY
7.1 Criteria of Reactor Performance
7.2 Factors of Economic Importance
7.3 Physicochemical Mechanisms
8 GENERAL GUIDE TO SELECTION OF REACTOR TYPE AND OPERATION
8.1 Choice of Reactor Type
8.2 Reaction Mechanism and Kinetics
8.3 Thermodynamics
8.4 Other Factors
9 GENERAL REFERENCES AND SOURCES OF
INFORMATION
APPENDICES
A RELATIONSHIP BEWTEEN DEFINED TERMS
FIGURES
1 DECISION TREE
2 RELATIVE YIELDS OF B FOR BATCH (OR PLUG FLOW) AND CST REACTORS
3 REACTOR SURVEY FORM
Heating and Cooling of Batch Processes
0 INTRODUCTION/PURPOSE
1 SCOPE
2 FIELD OF APPLICATION
3 DEFINITIONS
3.1 units
4 STATEMENT OF THE PROBLEM
5 DEVELOPMENT OF THE METHOD
5.1 Assumptions
5.2 Basic Equations
6 APPLICATION OF THE METHOD
6.1 Determining the Behavior of an Existing System
6.2 Specifying the Heat Transfer Duty for a New System
APPENDICES
A DERIVATION OF THE EQUATIONS
B WORKED EXAMPLES
FIGURES
1 CASES CONSIDERED
Reactor and Catalyst Design
0 INTRODUCTION/PURPOSE
1 SCOPE
2 FIELD OF APPLICATION
3 DEFINITIONS
4 CATALYST DESIGN
4.1 Equivalent Pellet Diameter
4.2 Voidage
4.3 Pellet Density
5 REACTOR DESIGN
6 CATALYST SUPPORT
6.1 Choice of Support
TABLES
1 CATALYST SUPPORT SHAPES
2 SECONDARY REFORMER SPREADSHEET
FIGURES
1 GRAPH OF EFFECTIVENESS v THIELE MODULUS
2 VARIATION OF COSTS WITH CATALYST SIZE
3 VARIATION OF COSTS WITH CATALYST BED VOIDAGE
4 VARIATION OF COSTS WITH VESSEL DIAMETER
SMR PRE-REFORMER DESIGN
Case Study #0618416GB/H
Contents
1. SMR Pre-Reformer Design
2. Inlet Baffle Design
3. Outlet Collector
4. Hold Down Grating
5. Floating Hold Down Screen
6. Catalyst Drop Out Nozzle
7. Thermowell Detail
8. Technical Performance requirements
9. SMR Pre-Reformer Isolation
Technical Review and Commentary on Proposed Design
APPENDIX
A. Operating / Mechanical Data
B. Materials Specifications
C. Fabrication and Inspection Requirements
D. Weights
E. Nozzle Data
F. Instrument Connections
G. Manholes
Design and Simulation of Continuous Distillation ColumnsGerard B. Hawkins
Design and Simulation of Continuous Distillation Columns
0 INTRODUCTION/PURPOSE
1 SCOPE
2 FIELD OF APPLICATION
3 DEFINITIONS
4 FRACTIONAL DISTILLATION
5 ROUGH METHOD OF COLUMN DESIGN
5.1 Sharp Separations
5.2 Sloppy Separations
6 DETAIL DESIGN USING THE CHEMCAD DISTILLATION PROGRAM
6.1 Sharp Separations
6.2 Sloppy Separations
7 COMPLEX COLUMNS
7.1 Multiple Feeds
7.2 Sidestream Take-Offs
8 DESIGN USING A LABORATORY COLUMN
SIMULATION
9 DESIGN USING ACTUAL PLANT DATA
9.1 Uprating or Debottlenecking Exercises
10 REFERENCES
APPENDICES
A WORKED EXAMPLE
B SLOPPY SEPARATIONS
C SIMULATION USING PLANT DATA : CASE HISTORIES
TABLES
Getting the Most Out of Your Refinery Hydrogen PlantGerard B. Hawkins
Getting the Most Out of Your Refinery Hydrogen Plant
Contents
Summary
1 Introduction
2 "On-purpose" Hydrogen Production
3 Operational Aspects
4 Uprating Options on the Steam Reformer
4.1 Steam Reforming Catalysts and Tube Metallurgy
4.2 Oxygen-blown Secondary Reformer
4.3 Pre-reforming
4.4 Post-reforming
5 Downstream Units
6 Summary of Uprating Options
7 Conclusions
The Design and Layout of Vertical Thermosyphon ReboilersGerard B. Hawkins
The Design and Layout of Vertical Thermosyphon Reboilers
0 INTRODUCTION/PURPOSE
1 SCOPE
2 FIELD OF APPLICATION
3 DEFINITIONS
4 THE DESIGN PROBLEM
5 COMPUTER PROGRAMS
6 GENERAL CONSIDERATIONS
6.1 Heating Medium Temperature
6.2 Fouling Resistance
7 DESIGN PARAMETERS
7.1 Overall Arrangement and Specifications
7.2 Geometry Elements
8 ANALYSIS OF COMMERCIALLY AVAILABLE
PROGRAM RESULTS
8.1 Main Results
8.2 Supplementary Results
8.3 Error Analysis
8.4 Adjustments to Design
9 OPERATING RANGE
10 CONTROL
10.1 Control of Condensing Heating Medium Pressure
10.2 Control of The Condensate Level
10.3 Control of Sensible Fluid Flow Rate
11 LAYOUT
11.1 Factors Influencing Design
11.2 A Standard Layout
12 BIBLIOGRAPHY
Reciprocating Compressors - Protection against Crank Case ExplosionsGerard B. Hawkins
Reciprocating Compressors - Protection against Crank Case Explosions
1 SCOPE
2 OIL MIST/AIR MIXTURE EXPLOSIONS
3 PREVENTION AND PROTECTION
3.1 Design
3.2 Maintenance and Operation
FIGURES
1 FLAMMABILITY LIMITS AND SPONTANEOUS IGNITION REGION FOR MIXTURES OF LUBRICATING OIL VAPOR IN AIR.
Selection of Heat Exchanger Types
0 INTRODUCTION/PURPOSE
1 SCOPE
2 FIELD OF APPLICATION
3 DEFINITIONS
4 BACKGROUND
5 FACTORS INFLUENCING SELECTION
5.1 Type of Duty
5.2 Temperatures and Pressures
5.3 Materials of Construction 5.4 Fouling
5.5 Safety and Reliability
5.6 Repairs
5.7 Design Methods
5.8 Dimensions and Weight
5.9 Cost
5.10 GBHE Experience
6 TYPES OF EXCHANGER
6.1 Shell and Tube Exchangers
6.2 Cylindrical Graphite Block Heat Exchangers
6.3 Cubic Graphite Block Heat Exchangers
6.4 Air Cooled Heat Exchangers
6.5 Gasketed Plate and Frame
6.6 Spiral Plate
6.7 Tube in Duct
6.8 Plate-fin
6.9 Printed Circuit Heat Exchanger (PCHE)
6.10 Scraped Surface/Wiped Film Exchangers
6.11 Welded or Brazed Plate
6.12 Double Pipe
6.13 Electric Heaters
6.14 Fired Process Heaters
TABLE
(1) ADVANTAGES AND DISADVANTAGES OF DIFFERENT SHELL AND TUBE DESIGNS
FIGURES
1 ESTIMATED MAIN PLANT ITEM COSTS
2 ESTIMATED INSTALLED COSTS
3 TEMA HEAT EXCHANGER NOMENCLATURE
4 F ‘CORRECTION FACTORS' : TEMA E SHELL WITH EVEN NUMBER OF PASSE
5 SHELL AND TUBE HEAT EXCHANGER HEAD TYPES
6 GENERAL ARRANGEMENT OF A CYLINDRICAL GRAPHITE BLOCK HEAT EXCHANGER
7 EXPLODED VIEW OF A CUBIC GRAPHITE BLOCK
HEAT EXCHANGER
8 TYPICAL AIR COOLED HEAT EXCHANGER
9 GENERAL VIEW OF ONE END OF A 3-STREAM
PLATE-FIN HEAT EXCHANGER
10 TYPICAL PCHE PLATE
11 VICARB ‘COMPABLOC' EXCHANGER
12 ‘BROWN FINTUBE' MULTITUBE HEAT EXCHANGER
13 FIRED HEATER : SCHEMATICS AND NOMENCLATURE
Gas-Solid-Liquid Mixing Systems
0 INTRODUCTION/PURPOSE
1 SCOPE
2 FIELD OF APPLICATION
3 DEFINITIONS
4 SELECTION OF EQUIPMENT
5 THREE-PHASE MASS TRANSFER WITH CHEMICAL REACTION
6 STIRRED VESSEL DESIGN
6.1 Agitator Design
6.2 Design for Solids Suspension
6.3 Vessel Design
6.4 Gas-Liquid Mass Transfer Coefficient and Surface Area
7 THREE-PHASE FLUIDIZED BEDS
7.1 Gas and Liquid Hold-Up
7.2 Calculation Procedure
7.3 Bubble Size
7.4 Mass Transfer
7.5 Heat Transfer
7.6 Elutriation
8 SLURRY REACTORS
8.1 Gas Rate
8.2 Mass Transfer
9 NOMENCLATURE
10 BIBLIOGRAPHY
Reactor Arrangement for Continuous Vapor Phase ChlorinationGerard B. Hawkins
Reactor Arrangement for Continuous Vapor Phase Chlorination
CONTENTS
1 BACKGROUND
2 REACTOR
3 CHEMICAL SYSTEM
4 PROCESS CHEMISTRY
5 KINETICS EXPERIMENTS AND MODELING
6 INTERPRETATION OF KINETICS INFORMATION
7 OPERATING CONDITIONS AND REACTOR DESIGN
8 REACTOR STABILITY AND CONTROL
FIGURES
1 POSTULATED REACTION PATHS FOR PROGRESSIVE CHLORINATION OF B-PICOLINE 3
2 CHLORINATION OF b-PICOLINE: MODEL PREDICTIONS OF PRODUCT DISTRIBUTION IN FULLY-MIXED REACTOR
3 TWO-STAGE REACTOR: RATE OF CHLORINATION OF b-PICOLINE
DOCUMENTS REFERRED TO IN THIS PROCESS ENGINEERING GUIDE
Distillation Sequences, Complex Columns and Heat IntegrationGerard B. Hawkins
Distillation Sequences, Complex Columns and Heat Integration
0 INTRODUCTION/PURPOSE
1 SCOPE
2 FIELD OF APPLICATION
3 DEFINITIONS
4 SEQUENCING OF SIMPLE COLUMNS
4.1 Sidestream Columns
4.2 Multi-Feed Columns
5 SIMPLE COLUMN SEQUENCING AND HEAT
INTEGRATION INTERACTIONS
5.1 Energy Quantity and Quality
5.2 Heat Integration within the Total Flowsheet
6 COMPLEX COLUMN ARRANGEMENTS
6.1 Indirect Sequence with Vapor Link
6.2 Sidestream Systems
6.3 Pre-Fractionator Systems
7 COMPLEX COLUMNS AND HEAT INTEGRATION
INTERACTIONS
FIGURES
1 DIRECT AND INDIRECT SEQUENCES
2 A SINGLE SIDESTREAM COLUMN REPLACING 2
SIMPLE COLUMNS
3 A TYPICAL MULTI-FEED COLUMN
4 TYPICAL GRAND COMPOSITION CURVE
5 TYPICAL INDIRECT SEQUENCE WITH VAPOUR LINK
6 SIDESTREAM STRIPPER AND SIDESTREAM
RECTIFIER
7 SIMPLEST PRE-FRACTIONATOR SYSTEM
8 SIMPLEST PRE-FRACTIONATOR SYSTEM
9 PETLYUK COLUMN
Thermal Design Margins for Heat Exchangers
0 INTRODUCTION/PURPOSE
1 SCOPE
2 FIELD OF APPLICATION
3 DEFINITIONS
4 TERMINOLOGY
5 REASONS FOR SPECIFYING A DESIGN MARGIN
5.1 Instantaneous Rates
5.2 Future Uprating
5.3 Plant Upsets
5.4 Process Control
5.5 Uncertainties in Properties
5.6 Uncertainties in Design Methods
5.7 Fouling
6 COMBINATION OF DESIGN MARGINS
7 CRITICAL AND NON-CRITICAL DUTIES
7.1 General
7.2 Penalties of Over-design
8 OPTIMIZATION OF EXCHANGER DUTY
9 WAYS OF PROVIDING DESIGN MARGINS
9.1 The Provision of Excess Surface
9.2 Decreasing the Design Temperature Difference
9.3 Increasing the Design Process Throughput
9.4 Increasing the Design Fouling Resistance
9.5 Reducing the Design Process Outlet Temperature Approach
9.6 Adjusting the Physical Properties
10 ACCURACY OF THE DESIGN METHODS FOR SHELL AND TUBE EXCHANGERS
10.1 Pressure Drop
10.2 Heat Transfer
11 SUGGESTED DESIGN MARGINS
11.1 No Phase Change Duties
11.2 Condensers
11.3 Boilers
12 EFFECT OF UNDER- OR OVER-SURFACE ON PERFORMANCE
FIGURES
1 EFFECT OF LENGTH ON EXCHANGER DUTY COUNTERCURRENT FLOW, C* = 1.0
2 EFFECT OF NUMBER OF TUBES ON EXCHANGER PERFORMANCE COUNTERCURRENT FLOW, C* = 1.0, ALL RESISTANCE IN TUBES
3 EFFECT OF TUBE LENGTH ON NUMBER OF TUBES, AREA AND PRESSURE DROP
DESIGN OF VENT GAS COLLECTION AND DESTRUCTION SYSTEMS Gerard B. Hawkins
DESIGN OF VENT GAS COLLECTION AND DESTRUCTION SYSTEMS
CONTENTS
1 INTRODUCTION
1.1 Purpose
1.2 Scope of this Guide
1.3 Use of the Guide
2 ENVIRONMENTAL ISSUES
2.1 Principal Concerns
2.2 Mechanisms for Ozone Formation
2.3 Photochemical Ozone Creation Potential
2.4 Health and Environmental Effects
2.5 Air Quality Standards for Ground Level Concentrations of Ozone, Targets for Reduction of VOC Discharges and Statutory Discharge Limits
3 VENTS REDUCTION PHILOSOPHY
3.1 Reduction at Source
3.2 End-of-pipe Treatment
4 METHODOLOGY FOR COLLECTION & ASSESSMENT OF PROCESS FLOW DATA
4.1 General
4.2 Identification of Vent Sources
4.3 Characterization of Vents
4.4 Quantification of Process Vent Flows
4.5 Component Flammability Data Collection
4.6 Identification of Operating Scenarios
4.7 Quantification of Flammability Characteristics for Combined Vents
4.8 Identification, Quantification and Assessment of Possibility of Air Ingress Routes
4.9 Tabulation of Data
4.10 Hazard Study and Risk Assessment
4.11 Note on Aqueous / Organic Wastes
4.12 Complexity of Systems
4.13 Summary
5 SAFE DESIGN OF VENT COLLECTION HEADER SYSTEMS
5.1 General
5.2 Process Design of Vent Headers
5.3 Liquid in Vent Headers
5.4 Materials of Construction
5.5 Static Electricity Hazard
5.6 Diversion Systems
5.7 Snuffing Systems
6 SAFE DESIGN OF THERMAL OXIDISERS
6.1 Introduction
6.2 Design Basis
6.3 Types of High Temperature Thermal Oxidizer
6.4 Refractories
6.5 Flue Gas Treatment
6.6 Control and Safety Systems
6.7 Project Program
6.8 Commissioning
6.9 Operational and Maintenance Management
APPENDICES
A GLOSSARY
B FLAMMABILITY
C EXAMPLE PROFORMA
D REFERENCES
DOCUMENTS REFERRED TO IN THIS PROCESS GUIDE
TABLE
1 PHOTOCHEMICAL OZONE CREATION POTENTIAL REFERENCED
TO ETHYLENE AS UNITY
FIGURES
1 SCHEMATIC OF TYPICAL VENT COLLECTION AND THERMAL OXIDIZER SYSTEM
2 TYPICAL KNOCK-OUT POT WITH LUTED DRAIN
3 SCHEMATIC OF DIVERSION SYSTEM
4 CONVENTIONAL VERTICAL THERMAL OXIDIZER
5 CONVENTIONAL OXIDIZER WITH INTEGRAL WATER SPARGER
6 THERMAL OXIDIZER WITH STAGED AIR INJECTION
7 DOWN-FIRED UNIT WITH WATER BATH QUENCH
8 FLAMELESS THERMAL OXIDATION UNIT
9 THERMAL OXIDIZER WITH REGENERATIVE HEAT RECOVERY
10 TYPICAL PROJECT PROGRAM
11 TYPICAL FLAMMABILITY DIAGRAM
12 EFFECT OF DILUTION WITH AIR
13 EFFECT OF DILUTION WITH AIR ON 100 Rm³ OF FLAMMABLE GAS
Fixed Bed Reactor Scale-up Checklist
The purpose of this checklist is to identify the stages and potential problems associated with the scale up of fixed bed reactors from the drawing board to the full scale plant, and to determine how they should be checked.
The checking can be done using various methods. These are:
• Literature data.
• Lab testing.
• Calculation.
• Modeling.
• Semi-tech testing.
• Piloting or Sidestream testing.
Identifying the stages that need to be addressed for a particular catalyst/reactor development will help in estimating the time needed for the development of the reactor
101 Things That Can Go Wrong on a Primary Reformer - Best Practices GuideGerard B. Hawkins
This document discusses common problems that can occur in primary reformers and associated equipment. It identifies issues that can lead to plant shutdowns or efficiency losses, grouping them under catalysts, tubes, furnace boxes, burners, flue gas ducts, headers, and refractories. Some examples discussed include carbon formation, tube overheating, flame impingement, leaks in air preheaters, combustion air maldistribution, and damage to coffins. The document provides an overview of these issues to improve plant reliability over its lifespan.
This document provides an overview of acetylene selective hydrogenation processes. It discusses how acetylene is extracted from hydrocarbon streams using solvent absorption or selective hydrogenation. The two main types of selective hydrogenation are front-end, which treats lighter feedstocks before fractionation, and tail-end, which treats C2 fractions after removal of lighter components. Tail-end hydrogenation is more common and uses palladium-based catalysts with high selectivity for acetylene. The document also reviews catalyst regeneration methods used to remove coke and restore activity.
Tube Wall Temperature Measurement On Steam Reformers - Best PracticesGerard B. Hawkins
GBH Enterprises provides guidance on best practices for measuring tube wall temperatures in steam reformers using optical pyrometers. It is important to measure temperatures accurately to prevent overheating tubes while maximizing plant efficiency. GBH recommends taking multiple temperature and background readings per tube using handheld pyrometers and an emissivity correction factor. Safety precautions like protective equipment are also advised. Detailed procedures are outlined for top-fired, side-fired and terrace wall furnace configurations.
The Preliminary Choice of Fan or Compressor
0 INTRODUCTION/PURPOSE
1 SCOPE
2 FIELD OF APPLICATION
3 DEFINITIONS
4 METHOD FOR PRELIMINARY SELECTION
OF COMPRESSOR
5 PROCESS DATA SHEET
5.1 Essential Data for the Completion of a
Process Data Sheet
5.2 Gas Properties
5.3 Discharge Requirements
6 PRELIMINARY CHOICE OF FAN AND
COMPRESSOR TYPE
6.1 Essential Data for Preliminary Selection
7 FAN AND COMPRESSOR APPLICATIONS
7.1 Fans
7.2 Centrifugal Compressors
7.3 Axial Compressors
7.4 Reciprocating Compressors
7.5 Screw Compressors
7.6 Positive Displacement Blowers
7.7 Sliding Vane Compressors
7.8 Liquid Ring Compressors
8 PROVISION OF INSTALLED SPARES
9 PRELIMINARY ESTIMATE OF COSTS
Reciprocating Compressors - Protection against Crank Case ExplosionsGerard B. Hawkins
Reciprocating Compressors - Protection against Crank Case Explosions
1 SCOPE
2 OIL MIST/AIR MIXTURE EXPLOSIONS
3 PREVENTION AND PROTECTION
3.1 Design
3.2 Maintenance and Operation
FIGURES
1 FLAMMABILITY LIMITS AND SPONTANEOUS IGNITION REGION FOR MIXTURES OF LUBRICATING OIL VAPOR IN AIR.
Selection of Heat Exchanger Types
0 INTRODUCTION/PURPOSE
1 SCOPE
2 FIELD OF APPLICATION
3 DEFINITIONS
4 BACKGROUND
5 FACTORS INFLUENCING SELECTION
5.1 Type of Duty
5.2 Temperatures and Pressures
5.3 Materials of Construction 5.4 Fouling
5.5 Safety and Reliability
5.6 Repairs
5.7 Design Methods
5.8 Dimensions and Weight
5.9 Cost
5.10 GBHE Experience
6 TYPES OF EXCHANGER
6.1 Shell and Tube Exchangers
6.2 Cylindrical Graphite Block Heat Exchangers
6.3 Cubic Graphite Block Heat Exchangers
6.4 Air Cooled Heat Exchangers
6.5 Gasketed Plate and Frame
6.6 Spiral Plate
6.7 Tube in Duct
6.8 Plate-fin
6.9 Printed Circuit Heat Exchanger (PCHE)
6.10 Scraped Surface/Wiped Film Exchangers
6.11 Welded or Brazed Plate
6.12 Double Pipe
6.13 Electric Heaters
6.14 Fired Process Heaters
TABLE
(1) ADVANTAGES AND DISADVANTAGES OF DIFFERENT SHELL AND TUBE DESIGNS
FIGURES
1 ESTIMATED MAIN PLANT ITEM COSTS
2 ESTIMATED INSTALLED COSTS
3 TEMA HEAT EXCHANGER NOMENCLATURE
4 F ‘CORRECTION FACTORS' : TEMA E SHELL WITH EVEN NUMBER OF PASSE
5 SHELL AND TUBE HEAT EXCHANGER HEAD TYPES
6 GENERAL ARRANGEMENT OF A CYLINDRICAL GRAPHITE BLOCK HEAT EXCHANGER
7 EXPLODED VIEW OF A CUBIC GRAPHITE BLOCK
HEAT EXCHANGER
8 TYPICAL AIR COOLED HEAT EXCHANGER
9 GENERAL VIEW OF ONE END OF A 3-STREAM
PLATE-FIN HEAT EXCHANGER
10 TYPICAL PCHE PLATE
11 VICARB ‘COMPABLOC' EXCHANGER
12 ‘BROWN FINTUBE' MULTITUBE HEAT EXCHANGER
13 FIRED HEATER : SCHEMATICS AND NOMENCLATURE
Gas-Solid-Liquid Mixing Systems
0 INTRODUCTION/PURPOSE
1 SCOPE
2 FIELD OF APPLICATION
3 DEFINITIONS
4 SELECTION OF EQUIPMENT
5 THREE-PHASE MASS TRANSFER WITH CHEMICAL REACTION
6 STIRRED VESSEL DESIGN
6.1 Agitator Design
6.2 Design for Solids Suspension
6.3 Vessel Design
6.4 Gas-Liquid Mass Transfer Coefficient and Surface Area
7 THREE-PHASE FLUIDIZED BEDS
7.1 Gas and Liquid Hold-Up
7.2 Calculation Procedure
7.3 Bubble Size
7.4 Mass Transfer
7.5 Heat Transfer
7.6 Elutriation
8 SLURRY REACTORS
8.1 Gas Rate
8.2 Mass Transfer
9 NOMENCLATURE
10 BIBLIOGRAPHY
Reactor Arrangement for Continuous Vapor Phase ChlorinationGerard B. Hawkins
Reactor Arrangement for Continuous Vapor Phase Chlorination
CONTENTS
1 BACKGROUND
2 REACTOR
3 CHEMICAL SYSTEM
4 PROCESS CHEMISTRY
5 KINETICS EXPERIMENTS AND MODELING
6 INTERPRETATION OF KINETICS INFORMATION
7 OPERATING CONDITIONS AND REACTOR DESIGN
8 REACTOR STABILITY AND CONTROL
FIGURES
1 POSTULATED REACTION PATHS FOR PROGRESSIVE CHLORINATION OF B-PICOLINE 3
2 CHLORINATION OF b-PICOLINE: MODEL PREDICTIONS OF PRODUCT DISTRIBUTION IN FULLY-MIXED REACTOR
3 TWO-STAGE REACTOR: RATE OF CHLORINATION OF b-PICOLINE
DOCUMENTS REFERRED TO IN THIS PROCESS ENGINEERING GUIDE
Distillation Sequences, Complex Columns and Heat IntegrationGerard B. Hawkins
Distillation Sequences, Complex Columns and Heat Integration
0 INTRODUCTION/PURPOSE
1 SCOPE
2 FIELD OF APPLICATION
3 DEFINITIONS
4 SEQUENCING OF SIMPLE COLUMNS
4.1 Sidestream Columns
4.2 Multi-Feed Columns
5 SIMPLE COLUMN SEQUENCING AND HEAT
INTEGRATION INTERACTIONS
5.1 Energy Quantity and Quality
5.2 Heat Integration within the Total Flowsheet
6 COMPLEX COLUMN ARRANGEMENTS
6.1 Indirect Sequence with Vapor Link
6.2 Sidestream Systems
6.3 Pre-Fractionator Systems
7 COMPLEX COLUMNS AND HEAT INTEGRATION
INTERACTIONS
FIGURES
1 DIRECT AND INDIRECT SEQUENCES
2 A SINGLE SIDESTREAM COLUMN REPLACING 2
SIMPLE COLUMNS
3 A TYPICAL MULTI-FEED COLUMN
4 TYPICAL GRAND COMPOSITION CURVE
5 TYPICAL INDIRECT SEQUENCE WITH VAPOUR LINK
6 SIDESTREAM STRIPPER AND SIDESTREAM
RECTIFIER
7 SIMPLEST PRE-FRACTIONATOR SYSTEM
8 SIMPLEST PRE-FRACTIONATOR SYSTEM
9 PETLYUK COLUMN
Thermal Design Margins for Heat Exchangers
0 INTRODUCTION/PURPOSE
1 SCOPE
2 FIELD OF APPLICATION
3 DEFINITIONS
4 TERMINOLOGY
5 REASONS FOR SPECIFYING A DESIGN MARGIN
5.1 Instantaneous Rates
5.2 Future Uprating
5.3 Plant Upsets
5.4 Process Control
5.5 Uncertainties in Properties
5.6 Uncertainties in Design Methods
5.7 Fouling
6 COMBINATION OF DESIGN MARGINS
7 CRITICAL AND NON-CRITICAL DUTIES
7.1 General
7.2 Penalties of Over-design
8 OPTIMIZATION OF EXCHANGER DUTY
9 WAYS OF PROVIDING DESIGN MARGINS
9.1 The Provision of Excess Surface
9.2 Decreasing the Design Temperature Difference
9.3 Increasing the Design Process Throughput
9.4 Increasing the Design Fouling Resistance
9.5 Reducing the Design Process Outlet Temperature Approach
9.6 Adjusting the Physical Properties
10 ACCURACY OF THE DESIGN METHODS FOR SHELL AND TUBE EXCHANGERS
10.1 Pressure Drop
10.2 Heat Transfer
11 SUGGESTED DESIGN MARGINS
11.1 No Phase Change Duties
11.2 Condensers
11.3 Boilers
12 EFFECT OF UNDER- OR OVER-SURFACE ON PERFORMANCE
FIGURES
1 EFFECT OF LENGTH ON EXCHANGER DUTY COUNTERCURRENT FLOW, C* = 1.0
2 EFFECT OF NUMBER OF TUBES ON EXCHANGER PERFORMANCE COUNTERCURRENT FLOW, C* = 1.0, ALL RESISTANCE IN TUBES
3 EFFECT OF TUBE LENGTH ON NUMBER OF TUBES, AREA AND PRESSURE DROP
DESIGN OF VENT GAS COLLECTION AND DESTRUCTION SYSTEMS Gerard B. Hawkins
DESIGN OF VENT GAS COLLECTION AND DESTRUCTION SYSTEMS
CONTENTS
1 INTRODUCTION
1.1 Purpose
1.2 Scope of this Guide
1.3 Use of the Guide
2 ENVIRONMENTAL ISSUES
2.1 Principal Concerns
2.2 Mechanisms for Ozone Formation
2.3 Photochemical Ozone Creation Potential
2.4 Health and Environmental Effects
2.5 Air Quality Standards for Ground Level Concentrations of Ozone, Targets for Reduction of VOC Discharges and Statutory Discharge Limits
3 VENTS REDUCTION PHILOSOPHY
3.1 Reduction at Source
3.2 End-of-pipe Treatment
4 METHODOLOGY FOR COLLECTION & ASSESSMENT OF PROCESS FLOW DATA
4.1 General
4.2 Identification of Vent Sources
4.3 Characterization of Vents
4.4 Quantification of Process Vent Flows
4.5 Component Flammability Data Collection
4.6 Identification of Operating Scenarios
4.7 Quantification of Flammability Characteristics for Combined Vents
4.8 Identification, Quantification and Assessment of Possibility of Air Ingress Routes
4.9 Tabulation of Data
4.10 Hazard Study and Risk Assessment
4.11 Note on Aqueous / Organic Wastes
4.12 Complexity of Systems
4.13 Summary
5 SAFE DESIGN OF VENT COLLECTION HEADER SYSTEMS
5.1 General
5.2 Process Design of Vent Headers
5.3 Liquid in Vent Headers
5.4 Materials of Construction
5.5 Static Electricity Hazard
5.6 Diversion Systems
5.7 Snuffing Systems
6 SAFE DESIGN OF THERMAL OXIDISERS
6.1 Introduction
6.2 Design Basis
6.3 Types of High Temperature Thermal Oxidizer
6.4 Refractories
6.5 Flue Gas Treatment
6.6 Control and Safety Systems
6.7 Project Program
6.8 Commissioning
6.9 Operational and Maintenance Management
APPENDICES
A GLOSSARY
B FLAMMABILITY
C EXAMPLE PROFORMA
D REFERENCES
DOCUMENTS REFERRED TO IN THIS PROCESS GUIDE
TABLE
1 PHOTOCHEMICAL OZONE CREATION POTENTIAL REFERENCED
TO ETHYLENE AS UNITY
FIGURES
1 SCHEMATIC OF TYPICAL VENT COLLECTION AND THERMAL OXIDIZER SYSTEM
2 TYPICAL KNOCK-OUT POT WITH LUTED DRAIN
3 SCHEMATIC OF DIVERSION SYSTEM
4 CONVENTIONAL VERTICAL THERMAL OXIDIZER
5 CONVENTIONAL OXIDIZER WITH INTEGRAL WATER SPARGER
6 THERMAL OXIDIZER WITH STAGED AIR INJECTION
7 DOWN-FIRED UNIT WITH WATER BATH QUENCH
8 FLAMELESS THERMAL OXIDATION UNIT
9 THERMAL OXIDIZER WITH REGENERATIVE HEAT RECOVERY
10 TYPICAL PROJECT PROGRAM
11 TYPICAL FLAMMABILITY DIAGRAM
12 EFFECT OF DILUTION WITH AIR
13 EFFECT OF DILUTION WITH AIR ON 100 Rm³ OF FLAMMABLE GAS
Fixed Bed Reactor Scale-up Checklist
The purpose of this checklist is to identify the stages and potential problems associated with the scale up of fixed bed reactors from the drawing board to the full scale plant, and to determine how they should be checked.
The checking can be done using various methods. These are:
• Literature data.
• Lab testing.
• Calculation.
• Modeling.
• Semi-tech testing.
• Piloting or Sidestream testing.
Identifying the stages that need to be addressed for a particular catalyst/reactor development will help in estimating the time needed for the development of the reactor
101 Things That Can Go Wrong on a Primary Reformer - Best Practices GuideGerard B. Hawkins
This document discusses common problems that can occur in primary reformers and associated equipment. It identifies issues that can lead to plant shutdowns or efficiency losses, grouping them under catalysts, tubes, furnace boxes, burners, flue gas ducts, headers, and refractories. Some examples discussed include carbon formation, tube overheating, flame impingement, leaks in air preheaters, combustion air maldistribution, and damage to coffins. The document provides an overview of these issues to improve plant reliability over its lifespan.
This document provides an overview of acetylene selective hydrogenation processes. It discusses how acetylene is extracted from hydrocarbon streams using solvent absorption or selective hydrogenation. The two main types of selective hydrogenation are front-end, which treats lighter feedstocks before fractionation, and tail-end, which treats C2 fractions after removal of lighter components. Tail-end hydrogenation is more common and uses palladium-based catalysts with high selectivity for acetylene. The document also reviews catalyst regeneration methods used to remove coke and restore activity.
Tube Wall Temperature Measurement On Steam Reformers - Best PracticesGerard B. Hawkins
GBH Enterprises provides guidance on best practices for measuring tube wall temperatures in steam reformers using optical pyrometers. It is important to measure temperatures accurately to prevent overheating tubes while maximizing plant efficiency. GBH recommends taking multiple temperature and background readings per tube using handheld pyrometers and an emissivity correction factor. Safety precautions like protective equipment are also advised. Detailed procedures are outlined for top-fired, side-fired and terrace wall furnace configurations.
The Preliminary Choice of Fan or Compressor
0 INTRODUCTION/PURPOSE
1 SCOPE
2 FIELD OF APPLICATION
3 DEFINITIONS
4 METHOD FOR PRELIMINARY SELECTION
OF COMPRESSOR
5 PROCESS DATA SHEET
5.1 Essential Data for the Completion of a
Process Data Sheet
5.2 Gas Properties
5.3 Discharge Requirements
6 PRELIMINARY CHOICE OF FAN AND
COMPRESSOR TYPE
6.1 Essential Data for Preliminary Selection
7 FAN AND COMPRESSOR APPLICATIONS
7.1 Fans
7.2 Centrifugal Compressors
7.3 Axial Compressors
7.4 Reciprocating Compressors
7.5 Screw Compressors
7.6 Positive Displacement Blowers
7.7 Sliding Vane Compressors
7.8 Liquid Ring Compressors
8 PROVISION OF INSTALLED SPARES
9 PRELIMINARY ESTIMATE OF COSTS
Batch Distillation
1 SCOPE
2 FIELD OF APPLICATION
3 DEFINITIONS
4 BACKGROUND TO THE DESIGN
4.1 General
4.2 Choice of batch/continuous operation
4.3 Boiling point curve and cut policy
4.4 Method of design
4.5 Scope of calculations required for design
5 SIMPLE BATCH DISTILLATION
6 FRACTIONAL BATCH DISTILLATION
6.1 General
6.2 Approximate methods
6.3 Rigorous design - use of a computer model
6.4 Other factors influencing the design
6.4.1 Occupation
6.4.2 Choice of Batch Rectification or Stripping
6.4.3 Batch size
6.4.4 Initial estimate of cut policy
6.4.5 Liquid Holdup
6.4.6 Total reflux operation and heating-up time
6.4.7 Column operating pressure
6.5 Optimum Design of the Batch Still
6.6 Special design problems
7 GENERAL ASPECTS OF EQUIPMENT DESIGN
7.1 Kettle reboilers
7.2 Column Internals
7.3 Condensers and reflux split boxes
8 PROCESS CONTROL AND INSTRUMENTATION IN
BATCH DISTILLATION
9 MECHANICAL DESIGN FEATURES
10 BIBLIOGRAPHY
APPENDICES
A McCABE - THIELE METHOD - TYPICAL EXAMPLE
This document is a process engineering guide from GBH Enterprises on mixing of miscible liquids. It provides information on selecting between mechanically agitated vessels, jet mixed vessels, and tubular mixers. It also discusses the key parameters in designing agitated vessels, including mixing time, power requirements, vortex formation, heat transfer, and flow/circulation. Design considerations and correlations are presented for each of these parameters to aid in the selection and design of mixing equipment for miscible liquids.
Data Sources For Calculating Chemical Reaction EquilibriaGerard B. Hawkins
Data Sources For Calculating Chemical Reaction Equilibria
0 INTRODUCTION/PURPOSE
1 SCOPE
2 FIELD OF APPLICATION
3 DEFINITIONS
4 BACKGROUND TO THEORY
5 BIBLIOGRAPHY
Solid Catalyzed Reactions
0 INTRODUCTION/PURPOSE
1 SCOPE
2 FIELD OF APPLICATION
3 DEFINITIONS
4 GENERAL BACKGROUND
4.1 General Considerations
5 SOLID CATALYZED GAS REACTIONS
5.1 Reaction Kinetics
5.2 Tests for Transport Limitations
5.3 Building a Reaction Kinetic Equation
6 INTRAPARTICLE
6.1 Types of Pore System
6.2 The Catalyst Effectiveness Factor
6.3 The Measurement of Effective Diffusivity
7 ENHANCEMENT OF INTRAPARTICLE
8 NOMENCLATURE
8.1 Dimensionless Parameters
8.2 Greek Letters
8.3 Subscripts
9 BIBLIOGRAPHY
9.1 Further Reading
APPENDICES
A LANGMUIR - HINSHELWOOD KINETICS
FIGURES
1 EFFECTIVE RATE CONSTANT
2 ITERATIVE APPROACH TO REACTOR MODEL
DEVELOPMENT
3 COMMON LABORATORY MICROREACTORS (FLOW TYPE)
4 THE BERTY REACTOR
5 STEPS IN BUILDING A REACTION RATE EQUATION
6 A CENTRAL-COMPOSITE DESIGN FOR TWO FACTORS
7 FIRST ORDER ISOTHERMAL IRREVERSIBLE
REACTION WITHIN A CATALYST SPHERE
8 INTEGRAL YIELD vs CONVERSION SHOWING EFFECT OF PELLET DIFFUSION
9 PREDICTED AND EXPERIMENTAL EFFECTIVENESS FACTORS
10 STRUCTURAL PERMEABILITY vs PRESSURE PARAMETER Z FOR BI-MODAL SUPPORTS
11 EFFECTIVENESS FACTOR vs THIELE MODULUS AND INTRAPARTICLE PECLET NUMBER
12 RELATIVE INCREASE IN CATALYST PERFORMANCE
VLE Data - Selection and Use
0 INTRODUCTION/PURPOSE
1 SCOPE
2 FIELD OF APPLICATION
3 DEFINITIONS
4 DIAGRAMMATIC REPRESENTATION OF IDEAL
AND NON-IDEAL SYSTEMS
4.1 Ideal Mixtures
4.2 Non-Ideal Mixtures
5 REVIEW OF VLE MODELS
5.1 Ideal Behavior in Both Phases
5.2 Liquid Phase Non-Idealities
5.3 High Pressure Systems
5.4 Special Models
6 SETTING UP A VLE MODEL
6.1 Define Problem
6.2 Select Data
6.3 Select Correlation(s)
6.4 Produce Model
7 AVOIDING PITFALLS
7.1 Experimental Data is Better than Estimates
7.2 Check Validity of Fitted Model
7.3 Check Limitations of Estimation Methods
7.4 Know Your System
7.5 Appreciate Errors and Effects
7.6 If in Doubt – Ask
8 A CASE STUDY
8.1 The Problem
8.2 The System
8.3 Data Available
8.4 Selected Correlation
8.5 Simulation
8.6 Selection of Model
9 RECOMMENDED READING
10 VLE EXPERTS IN GBHE
APPENDICES
A USE OF EXTENDED ANTOINE EQUATION
B USE OF WILSON EQUATION
C USEFUL METHODS OF ESTIMATING
D EQUATIONS OF STATE FOR VLE CALCULATIONS
TABLES
1 SUMMARY OF VLE METHODS
2 LIST OF USEFUL REFERENCES
FIGURES
1 VAPOR-LIQUID EQUILIBRIUM - IDEAL SOLUTION
BEHAVIOR
2 VAPOR-LIQUID EQUILIBRIUM - A GENERALISED
Y-X DIAGRAM
3 VAPOR-LIQUID EQUILIBRIUM - MINIMUM BOILING
AZEOTROPE
4 VAPOR-LIQUID EQUILIBRIUM - MAXIMUM BOILING
AZEOTROPE
5 VAPOR-LIQUID EQUILIBRIUM - MINIMUM BOILING
AZEOTROPE -TWO LIQUID PHASES
6 SENSITIVITY TO ERROR IN VLE DATA (BASED ON FENSKE EQUATION)
7(a) FITTING WILSON 'A' VALUES TO VLE DATA - CASE A
7(b) FITTING WILSON 'A' VALUES TO VLE DATA - CASE B
7(c) FITTING WILSON 'A' VALUES TO VLE DATA - CASE C
SYNOPSIS
The principles underlying centrifugal separation of particulate species are briefly considered, and the main types of separator available are noted. The procedures available for scale-up from laboratory or semi-technical data are then discussed in detail with particular reference to perhaps the most important class of machine for fine particle processing: the disc-nozzle centrifuge.
Starting with the basic concepts behind their design, discussion follows to explain the factors which may limit centrifuge performance. It is shown how a few simple; laboratory scale tests can give a valuable insight into the design and operation of full-scale industrial machines.
Centrifugal Compressors
SECTION ONE - ANTI-SURGE PROTECTION AND THROUGHPUT REGULATION
0 INTRODUCTION
1 SCOPE
2 MACHINE CHARACTERISTICS
2.1 Characteristics of a Single Compressor Stage
2.2 Characteristic of a Multiple Stage Having More
Than One Impeller
2.3 Use of Compressor Characteristics in Throughput
Regulation Schemes
3 MECHANISM AND EFFECTS OF SURGE
3.1 Basic Flow Instabilities
3.2 Occurrence of Surge
3.3 Intensity of Surge
3.4 Effects of Surge
3.5 Avoidance of Surge
3.6 Recovery from Surge
4 CONTROL SCHEMES INCLUDING SURGE PROTECTION
4.1 Output Control
4.2 Surge Protection
4.3 Surge Detection and Recovery
5 DYNAMIC CONSIDERATIONS
5.1 Interaction
5.2 Speed of Response of Antisurge Control System
6 SYSTEM EQUIPMENT SPECIFICATIONS
6.1 The Antisurge Control Valve
6.2 Non-return Valve
6.3 Pressure and flow measurement
6.4 Signal transmission
6.5 Controllers
7 TESTING
7.1 Determination of the Surge Line
7.2 Records
8 INLET GUIDE VANE UNITS
8.1 Application
8.2 Effect on Power Consumption of the Compressor
8.3 Effect of Gas Conditions, Properties and Contaminants
8.4 Aerodynamic Considerations
8.5 Control System Linearity
8.6 Actuator Specification
8.7 Avoidance of Surge
8.8 Features of Link Mechanisms
8.9 Limit Stops and Shear Links
APPENDICES
A LIST OF SYMBOLS AND PREFERRED UNITS
B WORKED EXAMPLE 1 COMPRESSOR WITH VARIABLE INLET PRESSURE AND VARIABLE GAS COMPOSITION
C WORKED EXAMPLE 2 A CONSTANT SPEED ~ STAGE COMPRESSOR WITH INTER-COOLING
D WORKED EXAMPLE 3 DYNAMIC RESPONSE OF THE ANTISURGE PROTECTION SYSTEM FOR A SERVICE AIR COMPRESSOR RUNNING AT CONSTANT SPEED
E EXAMPLE OF INLET GUIDE VANE REGULATION
FIGURES
2.1 TYPICAL COMPRESSOR STAGE CHARACTERISTIC PLOTTED WITH FLOW AT DISCHARGE CONDITIONS
2.2 TYPICAL COMPRESSOR STAGE CHARACTERISTIC PLOTTED WITH FLOW AT INLET CONDITIONS
2.3 PERFORMANCE CHARACTERISTICS OF A COMPRESSOR STAGE AT VARYING SPEEDS
2.4 SYSTEM WORKING POINT DEFINED BY INTERSECTION OF PROCESS AND COMPRESSOR CHARACTERISTICS
2.5 DISCHARGE THROTTLE REGULATION
2.6 BYPASS REGULATION
2.7 INLET THROTTLE REGULATION
2.8 INLET GUIDE VANE REGULATION
2.9 VARIABLE SPEED REGULATION
3.1 GAS PULSATION LEVELS FOR A CENTRIFUGAL COMPRESSOR
3.2 REPRESENTATION OF CYCLIC FLOW DURING SURGE OF LONG PERIOD
3.3 TYPICAL WAVEFORM OF DISCHARGE PRESSURE DURING SURGE
3.4 MULTIPLE SURGE LINE FOR A MULTISTAGE CENTRIFUGAL COMPRESSOR
3.5 TYPICAL MULTIPLE SURGE LINES FOR SINGLE STAGE AXIAL-FLOW COMPRESSOR
4.1 GENERAL SCHEMATIC FOR COMPRESSORS OPERATING IN PARALLEL TO FEED MULTIPLE USER PLANTS
4.2 ILLUSTRATION OF SAFETY MARGIN BETWEEN SURGE POINT AND SURGE PROTECTION POINT AT WHICH ANTISURGE SYSTEM IS ACTIVATED
4.3 ANTISURGE SYSTEM FOR COMPRESSOR WITH FLAT PERFO ..........
Fluid Separation
0 INTRODUCTION/PURPOSE
1 SCOPE
2 FIELD OF APPLICATION
3 DEFINITIONS
4 A SEPARATION LOGIC TREE
5 METHODS OF DISTILLATION
5.1 Fractional Distillation
5.2 Azeotropic Distillation
5.3 Extractive Distillation
6 LIQUID-LIQUID EXTRACTION
7 OTHER COMMERCIAL METHODS OF SEPARATION
7.1 Adsorption
7.2 Fractional Crystallization
7.3 Ion Exchange
7.4 Membrane Processes
7.4.1 Ultrafiltration
7.4.2 Reverse Osmosis
7.4.3 Pervaporation
7.4.4 Liquid Membranes
7.4.5 Gas Permeation
7.4.6 Dialysis
7.4.7 Electrodialysis
7.5 Supercritical Fluid Extraction
7.6 Dissociation Extraction
7.7 Foam Fractionation
7.8 Clathration
7.9 Chromatography
8. OTHER METHODS OF SEPARATION
8.1 Precipitation
8.2 Paper Chromatography
8.3 Ligand Specific Chromatography
8.4 Electrophoresis
8.5 Isoelectric Focusing
8.6 Thermal Diffusion
8.7 Sedimentation Ultracentrifugation
8.8 Isopycnic Ultracentrifugation
8.9 Molecular Distillation
8.10 Gel Filtration
APPENDICES
A AT A GLANCE CHART BASED ON FENSKE, UNDERWOOD
B A GENERALIZED y - x DIAGRAM
C TEMPERATURE - COMPOSITION DIAGRAMS FOR
AZEOTROPIC MIXTURES
D A TYPICAL y - x DIAGRAM FOR EXTRACTIVE DISTILLATION (SOLVENT FREE BASIS)
E RAPID ESTIMATION OF LIQUID-LIQUID EXTRACTION REQUIREMENTS
F LIQUID - LIQUID EXTRACTION - THE USE OF EXTRACT REFLUX
G SELECTIVITIES REQUIRED FOR EQUAL PLANT COSTS
FIGURE
1 SEPARATION LOGIC TREE
Chemical Process Conception
0 INTRODUCTION / PURPOSE
1 SCOPE
2 FIELD OF APPLICATION
3 DEFINITIONS
4 PRODUCT STRATEGY
4.1 General
4.2 Market for the Product
4.3 Production Costs
4.4 Process Technology
5 PRELIMINARY PROCESS INFORMATION
6 REACTION AND REACTOR
6.1 Batch vs Continuous
6.2 Multiple Reactors
7 RECYCLE
7.1 Recycle Structure
7.2 Classification of Chemicals
7.3 Effect of Recycle
7.4 Preliminary Estimation of Conversion
8 REACTOR TYPE AND PERFORMANCE
8.1 Conversion-Yield Effects
8.2 Heat Effects
8.3 Equilibrium Effects
8.4 Kinetic Effects
8.5 More Help with Reactor Design
9 SEPARATION SYSTEM
10 REVIEW
11 BIBLIOGRAPHY AND REFERENCES
11.1 Preliminary Flowsheeting
11.2 Physical Properties
11.3 Reactors
11.4 Separation
11.5 Costing
APPENDICES
A BASIC REACTOR SYSTEM DESIGN
B DISCUSSION BETWEEN A CHEMIST AND A
CHEMICAL ENGINEER
C BASIC SEPARATION STRATEGY
TABLES
1 CLASSIFICATION OF MATERIALS
FIGURES
1 FLOWCHART OF THE ITERATIVE PROCEDURE REQUIRED IN PROCESS AND PRODUCT SELECTION AND DEVELOPMENT
Mixing of Immiscible Liquids
0 INTRODUCTION/PURPOSE
1 SCOPE
2 FIELD OF APPLICATION
3 DEFINITIONS
4 EQUIPMENT
4.1 Agitated Tanks
4.2 Flow Mixers
4.3 'High Shear' Mixers
5 SYSTEM PHYSICAL PROPERTIES
5.1 Density
5.2 Viscosity
5.3 Interfacial Tension
6 STIRRED VESSELS
6.1 Design for Complete Dispersion
6.2 Prediction of Phase Inversion
6.3 Design for Mass Transfer
6.4 Design for Dispersed Phase Mixing
6.5 Hold-Up in Continuous Vessels
7 FLOW MIXERS
7.1 Design for Turbulent Conditions
7.2 Design for Laminar Conditions
TABLES
1 REYNOLDS NUMBER RANGES
FIGURES
1 STANDARD TANK CONFIGURATION
2 EXPERIMENTAL RELATIONSHIP BETWEEN MASS
TRANSFER COEFFICIENT AND POWER DENSITY
This document provides guidance on implementing procedures for managing critical pressure systems as outlined in PEG 4. It covers the design, manufacture, repair, modification and periodic examination of pressure vessels, piping systems, and pressure relief streams. Key requirements include using recognized standards, qualified personnel, design verification, registration of equipment, and periodic inspections to ensure safety. The document is intended to support the development of detailed local engineering procedures for managing pressure equipment over its lifecycle.
Hydrogen Compressors
Engineering Design Guide
1 SCOPE
2 PHYSICAL ROPERTIES
2.1 Data for Pure Hydrogen
2.2 Influence of Impurities
3 MATERIALS OF CONSTRUCTION
3.1 Hydrogen from Electrolytic Cells
3.2 Pure Hydrogen
4 DESIGN
4.1 Pulsation
4.2 Bypass
5 TESTING OR COMMISSIONING RECIPROCATING COMPRESSORS
6 LUBRICATION
7 LAYOUT
8 REFERENCES
FIGURES
1 MOLLIER CHART - HYDROGEN
2 COMPRESSIBILITY CHART
3 NELSON DIAGRAM
4 WATER CONTENT IN HYDROGEN FOR OIL-LUBRICATED COMPRESSORS AS GRAMM/M2 SWEPT CYLINDER AREA
Air Cooled Heat Exchanger Design
0 INTRODUCTION/PURPOSE
1 SCOPE
2 FIELD OF APPLICATION
3 DEFINITIONS
4 SUITABILITY FOR AIR COOLING
4.1 Options Available For Cooling
4.2 Choice of Cooling System
5 SPECIFICATION OF AN AIR COOLED HEAT
EXCHANGER
5.1 Description and Terminology
5.2 General
5.3 Thermal Duty and Design Margins
5.4 Process Pressure Drop
5.5 Design Ambient Conditions
5.6 Process Physical Properties
5.7 Mechanical Design Constraints
5.8 Arrangement
5.9 Air Side Fouling
5.10 Economic Factors in Design
6 CONTROL
7 PRESSURE RELIEF
8 ASSESSMENT OF OFFERS
8.1 General
8.2 Manual Checking Of Designs
8.3 Computer Assessment
8.4 Bid Comparison
9 FOULING AND CORROSION
9.1 Fouling
9.2 Corrosion
10 OPERATION AND MAINTENANCE
10.1 Performance Testing
10.2 Air-Side Cleaning
10.3 Mechanical Maintenance
10.4 Tube side Access
11 REFERENCES
Interpretation and Correlation of Viscometric Data
0 INTRODUCTION/PURPOSE
1 SCOPE
2 FIELD OF APPLICATION
3 DEFINITIONS
4 NON-NEWTONIAN FLUID BEHAVIOR
4.1 Introduction
4.2 Classification of Non-Newtonian Fluids
4.3 Caution
5 VISCOMETER MEASUREMENTS FOR
TIME-INDEPENDENT FLUIDS
5.1 Concentric Cylinder Viscometers
5.2 Cone and Plate Viscometers
5.3 Parallel Plate Viscometer
5.4 Tube or Capillary Viscometer
5.5 Checks for Consistency of Data and Interpretation
5.6 Estimate of Process Shear Rate
6 MODEL FITTING TO FLOW CURVES
6.1 Power Law
6.2 Bingham Plastic
6.3 Direct use of Numerical Data
6.4 Rheological Models Involving Temperature Dependence
7 CHARACTERIZATION OF TIME-DEPENDENT LIQUIDS
7.1 Sample Loading
7.2 Tests at Constant Shear Rate
7.3 Dynamic Response Measurement
7.4 Changes in Shear Rate
7.4 Concluding Remarks
8 TECHNIQUES FOR CHARACTERIZATION OF
VISCOELASTIC LIQUIDS
8.1 Stress Relaxation
8.2 Oscillatory Shear Measurements
8.3 Normal Force Measurement
8.4 Elongational Viscosity Measurement
9 NOMENCLATURE
10 BIBLIOGRAPHY
APPENDICES
A EQUATIONS FOR VISCOMETERS
A.1 EQUATIONS FOR CONCENTRIC CYLINDER
VISCOMETERS
A.2 EQUATIONS FOR CONE AND PLATE VISCOMETERS
A.3 EQUATIONS FOR PARALLEL PLATE VISCOMETER
A.4 EQUATIONS FOR TUBE OR CAPILLARY VISCOMETER
Estimation of Pressure Drop in Pipe Systems
0 INTRODUCTION/PURPOSE
1 SCOPE
2 FIELD OF APPLICATION
3 DEFINITIONS
3.1 units
4 SOURCES OF DATA
5 BASIC CONCEPTS
5.1 Equation for Pressure Change in a Flowing
Fluid
5.2 Static and Stagnation Pressures
5.3 Sonic Flow
6 INCOMPRESSIBLE FLOW IN PIPES OF CONSTANT
CROSS-SECTION
6.1 Straight Circular Pipes
6.2 Ducts of Non-circular Cross-section
6.3 Coils
6.4 General Equation for Incompressible Flow
in Pipes of Constant Cross-section
7 COMPRESSIBLE FLOW IN PIPES OF CONSTANT
CROSS-SECTION
7.1 Isothermal Flow
7.2 Adiabatic Flow
7.3 Estimation of Pressure Drop for Adiabatic
Flow in Pipes of Constant Cross-section
7.4 Ratio of Isothermal to Adiabatic Pressure Drop
8 FLOW IN PIPE FITTINGS
8.1 Incompressible Flow
8.2 Compressible Flow
9 FLOW IN BENDS
9.1 Incompressible Flow in Bends
9.2 Compressible Flow in Bends
10 CHANGES IN CROSS-SECTIONAL AREA
9.1 Incompressible Flow
9.2 Compressible Flow
11 ORIFICES, NOZZLES AND VENTURIS
11.1 Incompressible Flow through an Orifice
11.2 Compressible Flow through an Orifice or Nozzle
11.3 Venturi Choke Tubes
12 VALVES
12.1 General
12.2 Incompressible Flow in Valves
12.2 Compressible Flow in Valves
13 COMBINING AND DIVIDING FLOW
9.1 Incompressible Flow
9.2 Compressible Flow
14 COMPUTER PROGRAMS FOR FLUID FLOW
15 NOMENCLATURE
16 REFERENCES
APPENDICES
A BASIC THERMODYNAMICS
B COMPRESSIBLE FLOW THROUGH ORIFICES
C THE ‘TWO-K’ METHOD FOR FITTING PRESSURE LOSS
Pressure Relief Systems Vol 2
Causes of Relief Situations
This Volume 2 is a guide to the qualitative identification of common causes of overpressure in process equipment. It cannot be exhaustive; the process engineer and relief systems team should look for any credible situation in addition to those given in this Part which could lead to a need for pressure relief (a relief situation).
This document provides guidelines for engineering design of pressure relief systems. It discusses key principles such as identifying potential overpressure and underpressure causes, sizing relief systems to prevent hazards, and safely disposing of relieved materials. The guidelines cover statutory requirements, recommended design procedures, and documentation standards. The overall goal is to preserve equipment integrity and prevent failure from over or under pressure during all process phases.
GAS DISPERSION - A Definitive Guide to Accidental Releases of Heavy GasesGerard B. Hawkins
GAS DISPERSION - A Definitive Guide to Accidental Releases of Heavy Gases
This Process Safety Guide has been written with the aim of assisting process engineers, hazard analysts and environmental advisers in carrying out gas dispersion calculations. The Guide aims to provide assistance by:
• Improving awareness of the range of dispersion models available within GBHE, and providing guidance in choosing the most appropriate model for a particular application.
• Providing guidance to ensure that source terms and other model inputs are correctly specified, and the models are used within their range of applicability.
• Providing guidance to deal with particular topics in gas dispersion such as dense gas dispersion, complex terrain, and modeling the chemistry of oxides of nitrogen.
• Providing general background on air quality and dispersion modeling issues such as meteorology and air quality standards.
• Providing example calculations for real practical problems.
SCOPE
The gas dispersion guide contains the following Parts:
1 Fundamentals of meteorology.
2 Overview of air quality standards.
3 Comparison between different air quality models.
4 Designing a stack.
5 Dense gas dispersion.
6 Calculation of source terms.
7 Building wake effects.
8 Overview of the chemistry of the oxides of nitrogen.
9 Overview of the ADMS complex terrain module.
10 Overview of the ADMS deposition module.
11 ADMS examples.
12 Modeling odorous releases.
13 Bibliography of useful gas dispersion books and reports.
14 Glossary of gas dispersion modeling terms.
Appendix A : Modeling Wind Generation of Particulates.
APPENDIX B TABLE OF PROPERTY VALUES FOR SPECIFIC CHEMICALS
El impacto en el rendimiento del catalizador por envenenamiento y ensuciamien...Gerard B. Hawkins
El documento describe los procesos de refinería y catalizadores, así como los efectos del envenenamiento y ensuciamiento en el rendimiento de los catalizadores. El envenenamiento reduce la actividad de los catalizadores al bloquear los sitios activos o modificar la química de la superficie, lo que afecta la actividad y selectividad. Los niveles bajos de contaminantes tienen un mayor impacto en catalizadores con menor área de superficie. El envenenamiento también puede causar cambios estructurales en el catalizador y permitir
Theory of Carbon Formation in Steam Reforming
Contents
1 Introduction
2 Underpinning Theory
2.1 Conceptualization
2.2 Reforming Reactions
2.3 Carbon Formation Chemistry
2.3.1 Natural Gas
2.3.2 Carbon Formation for Naphtha Feeds
2.3.3 Carbon Gasification
2.4 Heat Transfer
3 Causes
3.1 Effects of Carbon Formation
3.2 Types of Carbon
4 What are the Effects of Carbon Formation?
4.1 Why does Carbon Formation Get Worse?
4.1.1 So what is the Next Step?
4.2 Consequences of Carbon Formation
4.3 Why does Carbon Form where it does?
4.3.1 Effect on Process Gas Temperature
4.4 Why does Carbon Formation Propagate Down the Tube?
4.4.1 Effect on Radiation on the Fluegas Side
4.5 Why does Carbon Formation propagate Up the Tube?
5 How do we Prevent Carbon Formation
5.1 The Role of Potash
5.2 Inclusion of Pre-reformer
5.3 Primary Reformer Catalyst Parameters
5.3.1 Activity
5.3.2 Heat Transfer
5.3.3 Increased Steam to Carbon Ratio
6 Steam Out
6.1 Why does increasing the Steam to Carbon Ratio Not Work?
6.2 Why does reducing the Feed Rate not help?
6.3 Fundamental Principles of Steam Outs
TABLES
1 Heat Transfer Coefficients in a Typical Reformer
2 Typical Catalyst Loading Options
FIGURES
1 Hot Bands
2 Conceptual Pellet
3 Naphtha Carbon Formation
4 Heat Transfer within an Reformer
5 Types of Carbon Formation
6 Effect of Carbon on Nickel Crystallites
7 Absorption of Heat
8 Comparison of "Base Case" v Carbon Forming Tube
9 Carbon Formation Vicious Circle
10 Temperature Profiles
11 Carbon Pinch Point
12 Carbon Formation
13 Effect on Process Gas Temperature
14 How does Carbon Propagate into an Unaffected Zone?
15 Movement of the Carbon Forming Region
16 Effect of Hot Bands on Radiative Heat Transfer
17 Effect of Potash on Carbon Formation
18 Application of a Pre-reformer
19 Effect of Activity on Carbon Formation
Adiabatic Reactor Analysis for Methanol Synthesis Plant Note Book Series: P...Gerard B. Hawkins
The document discusses adiabatic reactor analysis for methanol synthesis from syngas. It provides the reaction kinetics and calculates conversion, temperature, and reactor volume needed at different conversions. Energy and mass balances are used to derive relationships between conversion, temperature and reaction rate. Data is generated to plot conversion versus volumetric flow rate for reactor sizing. The plot indicates a continuous stirred tank reactor (CSTR) could achieve 85% conversion before switching to a plug flow reactor (PFR) for higher conversion with less volume.
STEAMING PROCEDURE FOR VULCAN STEAM REFORMING CATALYSTSGerard B. Hawkins
The document discusses procedures for steaming Vulcan steam reforming catalysts to recover from sulfur poisoning and carbon formation incidents. It describes maintaining steam flow at 30-40% of design levels and an outlet temperature above 780°C. Gas samples should be taken hourly to monitor CO2, CH4, H2S and SO2. Steaming is complete when CO2 levels stabilize over 2-3 samples after increasing the temperature. The process typically takes 12-24 hours to complete and closely monitors pressure drop and tube conditions. After steaming, the catalyst requires reduction before restarting hydrocarbon feed.
Calculation of an Ammonia Plant Energy Consumption: Gerard B. Hawkins
Calculation of an Ammonia Plant Energy Consumption:
Case Study: #06023300
Plant Note Book Series: PNBS-0602
CONTENTS
0 SCOPE
1 CALCULATION OF NATURAL GAS PROCESS FEED CONSUMPTION
2 CALCULATION OF NATURAL GAS PROCESS FUEL CONSUMPTION
3 CALCULATION OF NATURAL GAS CONSUMPTION FOR PILOT BURNERS OF FLARES
4 CALCULATION OF DEMIN. WATER FROM DEMIN. UNIT
5 CALCULATION OF DEMIN. WATER TO PACKAGE BOILERS
6 CALCULATION OF MP STEAM EXPORT
7 CALCULATION OF LP STEAM IMPORT
8 DETERMINATION OF ELECTRIC POWER CONSUMPTION
9 DETERMINATION OF THE TOTAL ENERGY CONSUMPTION OF THE AMMONIA PLANT ISBL
10 ADJUSTMENT OF ELECTRIC POWER CONSUMPTION FOR TEST RUN CONDITIONS
11 CALCULATION OF AMMONIA SHARE IN MP STEAM CONSUMPTION IN UTILITIES
12 CALCULATION OF AMMONIA SHARE IN ELECTRIC POWER CONSUMPTION IN UTILITIES
13 DETERMINATION OF THE TOTAL ENERGY CONSUMPTION OF THE AMMONIA PLANT OSBL
14 DETERMINATION OF THE TOTAL ENERGY CONSUMPTION OF THE AMMONIA PLANT
Ammonia Plant Technology
Pre-Commissioning Best Practices
GBHE-APT-0102
PICKLING & PASSIVATION
CONTENTS
1 PURPOSE OF THE WORK
2 CHEMICAL CONCEPT
3 TECHNICAL CONCEPT
4 WASTES & SAFETY CONCEPT
5 TARGET RESULTS
6 THE GENERAL CLEANING SEQUENCE MANAGEMENT
6.6.1 Pre-cleaning or “Physical Cleaning
6.6.2 Pre-rinsing
6.6.3 Chemical Cleaning
6.6.4 Critical Factors in Cleaning Success
6.6.5 Rinsing
6.6.6 Inspection and Re-Cleaning, if Necessary
7 Systems to be treated by Pickling/Passivation
Ammonia Plant Technology
Pre-Commissioning Best Practices
Piping and Vessels Flushing and Cleaning Procedure
CONTENTS
1 Scope
2 Aim/purpose
3 Responsibilities
4 Procedure
4.1 Main cleaning methods
4.1.1 Mechanical cleaning
4.1.2 Cleaning with air
4.1.3 Cleaning with steam (for steam networks only)
4.1.4 Cleaning with water
4.2 Choice of the cleaning method
4.3 Cleaning preparation
4.4 Protection of the devices included in the network
4.5 Protection of devices in the vicinity of the network
4.6 Water flushing procedure
4.6.1 Specific problems of water flushing
4.6.2 Preparation for water flushing
4.6.3 Performing a water flush
4.6.4 Cleanliness criteria
4.7 Air blowing procedure
4.7.1 Specific problems of air blowing
4.7.2 Preparation for air blowing
4.7.3 Performing air blowing
4.7.4 Cleanliness checks
4.8 Steam blowing procedure
4.8.1 Specific problems of steam blowing
4.8.2 Preparation for steam blowing
4.8.3 Performing steam blowing
4.8.4 Cleanliness checks
4.9 Chemical cleaning procedure
4.9.1 Specific problems of cleaning with a chemical solution
4.9.2 Preparation for chemical cleaning
4.9.3 Performing a chemical cleaning
4.9.4 Cleanliness criteria
4.10 Re-assembly - general guideline
4.11 Preservation of flushed piping
PRACTICAL GUIDE ON THE SELECTION OF PROCESS TECHNOLOGY FOR THE TREATMENT OF A...Gerard B. Hawkins
PRACTICAL GUIDE ON THE SELECTION OF PROCESS TECHNOLOGY FOR THE TREATMENT OF AQUEOUS ORGANIC EFFLUENT STREAMS
CONTENTS
0 INTRODUCTION/PURPOSE
1 SCOPE
2 FIELD OF APPLICATION
3 DEFINITIONS
3.1 IPU
3.2 AOS
3.3 BODs
3.4 COD
3.5 TOC
3.6 Toxicity
3.7 Refractory Organics/Hard COD
3.8 Heavy Metals
3.9 EA
3.10 Biological Treatment Terms
3.11 BATNEEC
3.12 BPEO
3.13 EQS/LV
3.14 IPC
3.15 VOC
3.16 F/M Ratio
3.17 MLSS
3.18 MLVSS
4 DESIGN/ECONOMIC GUIDELINES
5 EUROPEAN LEGISLATION
5.1 General
5.2 Integrated Pollution Control (IPC)
5.3 Best Available Techniques Not Entailing Excessive Costs (BATNEEC)
5.4 Best Practicable Environmental Option (BPEO)
5.5 Environmental Quality Standards(EQS)
6 IPU EXIT CONCENTRATION
7 SITE/LOCAL REQUIREMENTS
8 PROCESS SELECTION PROCEDURE
8.1 Waste Minimization Techniques (WMT)
8.2 AOS Stream Definition
8.3 Technical Check List
8.4 Preliminary Selection of Suitable Technologies
8.5 Process Sequences
8.6 Economic Evaluation
8.7 Process Selection
APPENDICES
A DIRECTIVE 76/464/EEC - LIST 1
B DIRECTIVE 76/464/EEC - LIST 2
C THE EUROPEAN COMMISSION PRIORITY CANDIDATE LIST
D THE UK RED LIST
E CURRENT VALUES FOR EUROPEAN COMMUNITY ENVIRONMENTAL QUALITY STANDARDS AND CORRESPONDING LIMIT VALUES
F ESTABLISHED TECHNOLOGIES
G EMERGING TECHNOLOGY
H PROPRIETARY/LESS COMMON TECHNOLOGIES
J COMPARATIVE COST DATA
PRACTICAL GUIDE ON THE REDUCTION OF DISCHARGES TO ATMOSPHERE OF VOLATILE ORGA...Gerard B. Hawkins
PRACTICAL GUIDE ON THE REDUCTION OF DISCHARGES TO ATMOSPHERE OF VOLATILE ORGANIC COMPOUNDS (VOCs)
FOREWORD
CONTENTS
1 INTRODUCTION
2 THE NEED FOR VOC CONTROL
3 CONTROL AT SOURCE
3.1 Choice or Solvent
3.2 Venting Arrangements
3.3 Nitrogen Blanketing
3.4 Pump Versus Pneumatic Transfer
3.5 Batch Charging
3.6 Reduction of Volumetric Flow
3.7 Stock Tank Design
4 DISCHARGE MEASUREMENT
4.1 By Inference or Calculation
4.2 Flow Monitoring Equipment
4.3 Analytical Instruments
4.4 Vent Emissions Database
5 ABATEMENT TECHNOLOGY
5.1 Available Options
5.2 Selection of Preferred Option
5.3 Condensation
5.4 Adsorption
5.5 Absorption
5.6 Thermal Incineration
5.7 Catalytic Oxidation
5.8 Biological Filtration
5.9 Combinations of Process technologies
5.10 Processes Under Development
6 GLOSSARY OF TERMS
7 REFERENCES
Appendix 1. Photochemical Ozone Creation Potentials
Appendix 2. Examples of Adsorption Preliminary Calculations
Appendix 3. Example of Thermal Incineration Heat and Mass Balance
Appendix 4. Cost Correlations
EMERGENCY ISOLATION OF CHEMICAL PLANTS
CONTENTS
1 Introduction
2 When should Emergency Isolation Valves be Installed
3 Emergency Isolation Valves and Associated Equipment
3.1 Installations on existing plant
3.2 Actuators
3.3 Power to close or power to open
3.4 The need for testing
3.5 Hand operated Emergency Valves
3.6 The need to stop pumps in an emergency
3.7 Location of Operating Buttons
3.8 Use of control valves for Isolation
4 Detection of Leaks and Fires
5 Precautions during Maintenance
6 Training Operators to use Emergency Isolation Valves
7 Emergency Isolation when no remotely operated valve is available
References
Glossary
Appendix I Some Fires or Serious Escapes of Flammable Gases or Liquids that could have been controlled by Emergency Isolation Valves
Appendix II Some typical Installations
Amine Gas Treating Unit - Best Practices - Troubleshooting Guide Gerard B. Hawkins
Amine Gas Treating Unit Best Practices - Troubleshooting Guide for H2S/CO2 Amine Systems
Contents
Process Capabilities for gas treating process
Typical Amine Treating
Typical Amine System Improvements
Primary Equipment Overview
Inlet Gas Knockout
Absorber
Three Phase Flash Tank
Lean/Rich Heat Exchanger
Regenerator
Filtration
Amine Reclaimer
Operating Difficulties Overview
Foaming
Failure to Meet Gas Specification
Solvent Losses
Corrosion
Typical Amine System Improvements
Degradation of Amines and Alkanolamines during Sour Gas Treating
APPENDIX
Best Practices - Troubleshooting Guide
Investigation of the Potential Use of (IILs) Immobilized Ionic Liquids in Sha...Gerard B. Hawkins
The document discusses using immobilized ionic liquids (IILs) in shale gas sweetening reactions. It proposes immobilizing a cobalt catalyst in the surface ionic liquid layer of a solid supported ionic liquid catalyst. This would create a "homogeneous catalyst" dissolved within the fixed IIL layer. Competing reactions like oxidation of sulfides to sulfones would need to be considered. Related work on using similar approaches for hydroformylation reactions is referenced. The concept aims to develop a solid IIL catalyst for sweetening reactions involving oxidation using techniques from other areas like hydroformylation.
El documento proporciona una descripción general de los servicios y tecnologías de procesamiento de catalizadores de GBH Enterprises Ltd. (GBHE), incluyendo refinación de petróleo, procesamiento de gas, industrias petroquímicas y venta de catalizadores. GBHE ofrece servicios de ingeniería, soporte técnico y consultoría, así como una línea de catalizadores patentados para aplicaciones como desulfuración y purificación de gas.
Infrastructure Challenges in Scaling RAG with Custom AI modelsZilliz
Building Retrieval-Augmented Generation (RAG) systems with open-source and custom AI models is a complex task. This talk explores the challenges in productionizing RAG systems, including retrieval performance, response synthesis, and evaluation. We’ll discuss how to leverage open-source models like text embeddings, language models, and custom fine-tuned models to enhance RAG performance. Additionally, we’ll cover how BentoML can help orchestrate and scale these AI components efficiently, ensuring seamless deployment and management of RAG systems in the cloud.
Ivanti’s Patch Tuesday breakdown goes beyond patching your applications and brings you the intelligence and guidance needed to prioritize where to focus your attention first. Catch early analysis on our Ivanti blog, then join industry expert Chris Goettl for the Patch Tuesday Webinar Event. There we’ll do a deep dive into each of the bulletins and give guidance on the risks associated with the newly-identified vulnerabilities.
GraphRAG for Life Science to increase LLM accuracyTomaz Bratanic
GraphRAG for life science domain, where you retriever information from biomedical knowledge graphs using LLMs to increase the accuracy and performance of generated answers
Programming Foundation Models with DSPy - Meetup SlidesZilliz
Prompting language models is hard, while programming language models is easy. In this talk, I will discuss the state-of-the-art framework DSPy for programming foundation models with its powerful optimizers and runtime constraint system.
Removing Uninteresting Bytes in Software FuzzingAftab Hussain
Imagine a world where software fuzzing, the process of mutating bytes in test seeds to uncover hidden and erroneous program behaviors, becomes faster and more effective. A lot depends on the initial seeds, which can significantly dictate the trajectory of a fuzzing campaign, particularly in terms of how long it takes to uncover interesting behaviour in your code. We introduce DIAR, a technique designed to speedup fuzzing campaigns by pinpointing and eliminating those uninteresting bytes in the seeds. Picture this: instead of wasting valuable resources on meaningless mutations in large, bloated seeds, DIAR removes the unnecessary bytes, streamlining the entire process.
In this work, we equipped AFL, a popular fuzzer, with DIAR and examined two critical Linux libraries -- Libxml's xmllint, a tool for parsing xml documents, and Binutil's readelf, an essential debugging and security analysis command-line tool used to display detailed information about ELF (Executable and Linkable Format). Our preliminary results show that AFL+DIAR does not only discover new paths more quickly but also achieves higher coverage overall. This work thus showcases how starting with lean and optimized seeds can lead to faster, more comprehensive fuzzing campaigns -- and DIAR helps you find such seeds.
- These are slides of the talk given at IEEE International Conference on Software Testing Verification and Validation Workshop, ICSTW 2022.
Your One-Stop Shop for Python Success: Top 10 US Python Development Providersakankshawande
Simplify your search for a reliable Python development partner! This list presents the top 10 trusted US providers offering comprehensive Python development services, ensuring your project's success from conception to completion.
HCL Notes und Domino Lizenzkostenreduzierung in der Welt von DLAUpanagenda
Webinar Recording: https://www.panagenda.com/webinars/hcl-notes-und-domino-lizenzkostenreduzierung-in-der-welt-von-dlau/
DLAU und die Lizenzen nach dem CCB- und CCX-Modell sind für viele in der HCL-Community seit letztem Jahr ein heißes Thema. Als Notes- oder Domino-Kunde haben Sie vielleicht mit unerwartet hohen Benutzerzahlen und Lizenzgebühren zu kämpfen. Sie fragen sich vielleicht, wie diese neue Art der Lizenzierung funktioniert und welchen Nutzen sie Ihnen bringt. Vor allem wollen Sie sicherlich Ihr Budget einhalten und Kosten sparen, wo immer möglich. Das verstehen wir und wir möchten Ihnen dabei helfen!
Wir erklären Ihnen, wie Sie häufige Konfigurationsprobleme lösen können, die dazu führen können, dass mehr Benutzer gezählt werden als nötig, und wie Sie überflüssige oder ungenutzte Konten identifizieren und entfernen können, um Geld zu sparen. Es gibt auch einige Ansätze, die zu unnötigen Ausgaben führen können, z. B. wenn ein Personendokument anstelle eines Mail-Ins für geteilte Mailboxen verwendet wird. Wir zeigen Ihnen solche Fälle und deren Lösungen. Und natürlich erklären wir Ihnen das neue Lizenzmodell.
Nehmen Sie an diesem Webinar teil, bei dem HCL-Ambassador Marc Thomas und Gastredner Franz Walder Ihnen diese neue Welt näherbringen. Es vermittelt Ihnen die Tools und das Know-how, um den Überblick zu bewahren. Sie werden in der Lage sein, Ihre Kosten durch eine optimierte Domino-Konfiguration zu reduzieren und auch in Zukunft gering zu halten.
Diese Themen werden behandelt
- Reduzierung der Lizenzkosten durch Auffinden und Beheben von Fehlkonfigurationen und überflüssigen Konten
- Wie funktionieren CCB- und CCX-Lizenzen wirklich?
- Verstehen des DLAU-Tools und wie man es am besten nutzt
- Tipps für häufige Problembereiche, wie z. B. Team-Postfächer, Funktions-/Testbenutzer usw.
- Praxisbeispiele und Best Practices zum sofortigen Umsetzen
Things to Consider When Choosing a Website Developer for your Website | FODUUFODUU
Choosing the right website developer is crucial for your business. This article covers essential factors to consider, including experience, portfolio, technical skills, communication, pricing, reputation & reviews, cost and budget considerations and post-launch support. Make an informed decision to ensure your website meets your business goals.
AI-Powered Food Delivery Transforming App Development in Saudi Arabia.pdfTechgropse Pvt.Ltd.
In this blog post, we'll delve into the intersection of AI and app development in Saudi Arabia, focusing on the food delivery sector. We'll explore how AI is revolutionizing the way Saudi consumers order food, how restaurants manage their operations, and how delivery partners navigate the bustling streets of cities like Riyadh, Jeddah, and Dammam. Through real-world case studies, we'll showcase how leading Saudi food delivery apps are leveraging AI to redefine convenience, personalization, and efficiency.
Essentials of Automations: The Art of Triggers and Actions in FMESafe Software
In this second installment of our Essentials of Automations webinar series, we’ll explore the landscape of triggers and actions, guiding you through the nuances of authoring and adapting workspaces for seamless automations. Gain an understanding of the full spectrum of triggers and actions available in FME, empowering you to enhance your workspaces for efficient automation.
We’ll kick things off by showcasing the most commonly used event-based triggers, introducing you to various automation workflows like manual triggers, schedules, directory watchers, and more. Plus, see how these elements play out in real scenarios.
Whether you’re tweaking your current setup or building from the ground up, this session will arm you with the tools and insights needed to transform your FME usage into a powerhouse of productivity. Join us to discover effective strategies that simplify complex processes, enhancing your productivity and transforming your data management practices with FME. Let’s turn complexity into clarity and make your workspaces work wonders!
Let's Integrate MuleSoft RPA, COMPOSER, APM with AWS IDP along with Slackshyamraj55
Discover the seamless integration of RPA (Robotic Process Automation), COMPOSER, and APM with AWS IDP enhanced with Slack notifications. Explore how these technologies converge to streamline workflows, optimize performance, and ensure secure access, all while leveraging the power of AWS IDP and real-time communication via Slack notifications.
UiPath Test Automation using UiPath Test Suite series, part 6DianaGray10
Welcome to UiPath Test Automation using UiPath Test Suite series part 6. In this session, we will cover Test Automation with generative AI and Open AI.
UiPath Test Automation with generative AI and Open AI webinar offers an in-depth exploration of leveraging cutting-edge technologies for test automation within the UiPath platform. Attendees will delve into the integration of generative AI, a test automation solution, with Open AI advanced natural language processing capabilities.
Throughout the session, participants will discover how this synergy empowers testers to automate repetitive tasks, enhance testing accuracy, and expedite the software testing life cycle. Topics covered include the seamless integration process, practical use cases, and the benefits of harnessing AI-driven automation for UiPath testing initiatives. By attending this webinar, testers, and automation professionals can gain valuable insights into harnessing the power of AI to optimize their test automation workflows within the UiPath ecosystem, ultimately driving efficiency and quality in software development processes.
What will you get from this session?
1. Insights into integrating generative AI.
2. Understanding how this integration enhances test automation within the UiPath platform
3. Practical demonstrations
4. Exploration of real-world use cases illustrating the benefits of AI-driven test automation for UiPath
Topics covered:
What is generative AI
Test Automation with generative AI and Open AI.
UiPath integration with generative AI
Speaker:
Deepak Rai, Automation Practice Lead, Boundaryless Group and UiPath MVP
1. GBH Enterprises, Ltd.
Process Engineering Guide:
GBHE-PEG-MIX-700
How to Use the GBHE Mixing Guides
Information contained in this publication or as otherwise supplied to Users is
believed to be accurate and correct at time of going to press, and is given in
good faith, but it is for the User to satisfy itself of the suitability of the information
for its own particular purpose. GBHE gives no warranty as to the fitness of this
information for any particular purpose and any implied warranty or condition
(statutory or otherwise) is excluded except to the extent that exclusion is
prevented by law. GBHE accepts no liability resulting from reliance on this
information. Freedom under Patent, Copyright and Designs cannot be assumed.
Refinery Process Stream Purification Refinery Process Catalysts Troubleshooting Refinery Process Catalyst Start-Up / Shutdown
Activation Reduction In-situ Ex-situ Sulfiding Specializing in Refinery Process Catalyst Performance Evaluation Heat & Mass
Balance Analysis Catalyst Remaining Life Determination Catalyst Deactivation Assessment Catalyst Performance
Characterization Refining & Gas Processing & Petrochemical Industries Catalysts / Process Technology - Hydrogen Catalysts /
Process Technology – Ammonia Catalyst Process Technology - Methanol Catalysts / process Technology – Petrochemicals
Specializing in the Development & Commercialization of New Technology in the Refining & Petrochemical Industries
Web Site: www.GBHEnterprises.com
2. Process Engineering Guide:
How to Use the GBHE Mixing
Guides
CONTENTS
SECTION
0
INTRODUCTION/PURPOSE
3
1
SCOPE
3
2
FIELD OF APPLICATION
3
3
DEFINITIONS
3
4
THE MIXING GUIDES
3
4.1
4.2
Mixing Guides
GBHE Mixing and Agitation Manual
3
3
5
DEVICE SELECTION
3
6
MIXING QUESTIONNAIRE
5
6.1
6.2
6.3
6.4
6.5
6.6
6.7
6.8
6.9
6.10
What is being mixed?
Why is it being mixed?
How is it to be mixed?
Is Heat Transfer Important?
Is Mixing Time Important?
Is Inventory Important?
Is Subsequent Phase Separation Important?
What Quantities?
What are the Selection Criteria?
What Data are required?
5
5
5
6
6
6
6
6
6
6
Refinery Process Stream Purification Refinery Process Catalysts Troubleshooting Refinery Process Catalyst Start-Up / Shutdown
Activation Reduction In-situ Ex-situ Sulfiding Specializing in Refinery Process Catalyst Performance Evaluation Heat & Mass
Balance Analysis Catalyst Remaining Life Determination Catalyst Deactivation Assessment Catalyst Performance
Characterization Refining & Gas Processing & Petrochemical Industries Catalysts / Process Technology - Hydrogen Catalysts /
Process Technology – Ammonia Catalyst Process Technology - Methanol Catalysts / process Technology – Petrochemicals
Specializing in the Development & Commercialization of New Technology in the Refining & Petrochemical Industries
Web Site: www.GBHEnterprises.com
3. 7
BASICS
7
7.1
7.2
7.3
7.4
7.5
Bulk Movement
Shear and Elongation
Turbulent Diffusion
Molecular Diffusion
Mixing Mechanisms
8
8
8
9
9
APPENDICES
A
ROTATING MIXING DEVICES
11
B
MIXING DEVICES WITHOUT MOVING PARTS
18
Refinery Process Stream Purification Refinery Process Catalysts Troubleshooting Refinery Process Catalyst Start-Up / Shutdown
Activation Reduction In-situ Ex-situ Sulfiding Specializing in Refinery Process Catalyst Performance Evaluation Heat & Mass
Balance Analysis Catalyst Remaining Life Determination Catalyst Deactivation Assessment Catalyst Performance
Characterization Refining & Gas Processing & Petrochemical Industries Catalysts / Process Technology - Hydrogen Catalysts /
Process Technology – Ammonia Catalyst Process Technology - Methanol Catalysts / process Technology – Petrochemicals
Specializing in the Development & Commercialization of New Technology in the Refining & Petrochemical Industries
Web Site: www.GBHEnterprises.com
4. TABLES
1
SUMMARY OF TYPICAL USES OF MIXING DEVICES
4
FIGURES
1
CHARACTERISTICS OF VARIOUS DEVICES IN TERMS
OF BULK FLOW
9
2
TANK LAYOUT
11
3
PITCHED BLADE TURBINE
12
4
DISC TURBINE
12
5
PROPELLER
13
6
RETREAT CURVED BLADE TURBINE
13
7
CONCAVE BLADE TURBINE
14
8
'GASFOIL' AGITATOR
14
9
'HYDROFOIL' AGITATOR
14
10
HELICAL SCREW STIRRER
15
11
HELICAL RIBBON STIRRER
15
12
ANCHOR AGITATOR
16
13
BENT ANCHOR
16
14
”SAWTOOTH” DISC DISPERSER
17
15
”HIGH SHEAR” ROTOR-STATOR MIXER
17
16
COAXIAL JET FLOW MIXER
18
17
SIDE ENTRY JET FLOW MIXER
18
Refinery Process Stream Purification Refinery Process Catalysts Troubleshooting Refinery Process Catalyst Start-Up / Shutdown
Activation Reduction In-situ Ex-situ Sulfiding Specializing in Refinery Process Catalyst Performance Evaluation Heat & Mass
Balance Analysis Catalyst Remaining Life Determination Catalyst Deactivation Assessment Catalyst Performance
Characterization Refining & Gas Processing & Petrochemical Industries Catalysts / Process Technology - Hydrogen Catalysts /
Process Technology – Ammonia Catalyst Process Technology - Methanol Catalysts / process Technology – Petrochemicals
Specializing in the Development & Commercialization of New Technology in the Refining & Petrochemical Industries
Web Site: www.GBHEnterprises.com
5. 18
KENICS STATIC MIXERS
19
19
ROSS LLPD MOTIONLESS MIXER
19
20
SULZER SMV
20
21
SULZER SMX
20
DOCUMENTS REFERRED TO IN THIS PROCESS
ENGINEERING GUIDE
21
Refinery Process Stream Purification Refinery Process Catalysts Troubleshooting Refinery Process Catalyst Start-Up / Shutdown
Activation Reduction In-situ Ex-situ Sulfiding Specializing in Refinery Process Catalyst Performance Evaluation Heat & Mass
Balance Analysis Catalyst Remaining Life Determination Catalyst Deactivation Assessment Catalyst Performance
Characterization Refining & Gas Processing & Petrochemical Industries Catalysts / Process Technology - Hydrogen Catalysts /
Process Technology – Ammonia Catalyst Process Technology - Methanol Catalysts / process Technology – Petrochemicals
Specializing in the Development & Commercialization of New Technology in the Refining & Petrochemical Industries
Web Site: www.GBHEnterprises.com
6. 0
INTRODUCTION/PURPOSE
This Guide is one in a series of Mixing Guides and has been prepared for GBH
Enterprises.
1
SCOPE
This Guide directs the user to the most appropriate Guides to solve a mixing
problem. It does so by classifying the mixing systems, by asking a series of
questions and by defining the common terminology.
2
FIELD OF APPLICATION
This Guide applies to Process Engineers in GBH Enterprises worldwide.
3
DEFINITIONS
No specific definitions apply to this Guide.
4
THE MIXING GUIDES
4.1
Mixing Guides
Guidance on Mixing is available from two sources, the Mixing Guides and the
GBHE Mixing and Agitation Manual.
Mixing Guides are intended to provide initial guidance and a quick design for
uncomplicated mixing tasks in research, development and production. They
concentrate on recommendations and design or scale-up procedures.
The Mixing Guides are designated GBHE-PEG-MIX-XXX where the last three
digits identify the individual guides.
Refinery Process Stream Purification Refinery Process Catalysts Troubleshooting Refinery Process Catalyst Start-Up / Shutdown
Activation Reduction In-situ Ex-situ Sulfiding Specializing in Refinery Process Catalyst Performance Evaluation Heat & Mass
Balance Analysis Catalyst Remaining Life Determination Catalyst Deactivation Assessment Catalyst Performance
Characterization Refining & Gas Processing & Petrochemical Industries Catalysts / Process Technology - Hydrogen Catalysts /
Process Technology – Ammonia Catalyst Process Technology - Methanol Catalysts / process Technology – Petrochemicals
Specializing in the Development & Commercialization of New Technology in the Refining & Petrochemical Industries
Web Site: www.GBHEnterprises.com
7. 4.2
GBHE Mixing and Agitation Manual
The GBHE Mixing and Agitation Manual contains more detail, background to the
correlations and recommendations, many more references and is the repository
of the collective know-how. It provides greater insight and is thus better placed to
advise on more complex or unusual mixing problems.
5
DEVICE SELECTION
The range of devices covered by this series of Guides is summarized in Table 1.
Many of the duties could be performed by two or three different devices; it is
worthwhile considering the options before embarking on the detail design.
Appendix A illustrates typical rotating mixing devices and some typical ratios of
dimensions for agitated tanks. Appendix B shows devices without moving parts,
i.e. static and coaxial jet mixers.
Refinery Process Stream Purification Refinery Process Catalysts Troubleshooting Refinery Process Catalyst Start-Up / Shutdown
Activation Reduction In-situ Ex-situ Sulfiding Specializing in Refinery Process Catalyst Performance Evaluation Heat & Mass
Balance Analysis Catalyst Remaining Life Determination Catalyst Deactivation Assessment Catalyst Performance
Characterization Refining & Gas Processing & Petrochemical Industries Catalysts / Process Technology - Hydrogen Catalysts /
Process Technology – Ammonia Catalyst Process Technology - Methanol Catalysts / process Technology – Petrochemicals
Specializing in the Development & Commercialization of New Technology in the Refining & Petrochemical Industries
Web Site: www.GBHEnterprises.com
8. TABLE 1
SUMMARY OF TYPICAL USES OF MIXING DEVICES
Refinery Process Stream Purification Refinery Process Catalysts Troubleshooting Refinery Process Catalyst Start-Up / Shutdown
Activation Reduction In-situ Ex-situ Sulfiding Specializing in Refinery Process Catalyst Performance Evaluation Heat & Mass
Balance Analysis Catalyst Remaining Life Determination Catalyst Deactivation Assessment Catalyst Performance
Characterization Refining & Gas Processing & Petrochemical Industries Catalysts / Process Technology - Hydrogen Catalysts /
Process Technology – Ammonia Catalyst Process Technology - Methanol Catalysts / process Technology – Petrochemicals
Specializing in the Development & Commercialization of New Technology in the Refining & Petrochemical Industries
Web Site: www.GBHEnterprises.com
9. 6
MIXING QUESTIONNAIRE
The objective of the following questions is to act as a check list for the designer.
The list is not, however, exhaustive but is intended to stimulate ideas.
6.1
What is being mixed?
Type of Mixture
Mixing Guide
GBHE Mixing and
Agitation Manual
Miscible Liquids
GBHE-PEG-MIX-701
Section A
Gas-Gas
GBHE-PEG-MIX-702
Section B
Solid-Liquid
GBHE-PEG-MIX-703
GBHE-PEG-MIX-709
Section C
Section D4
Immiscible Liquids
GBHE-PEG-MIX-704
GBHE-PEG-MIX-709
Section D
Section D4
Gas-Liquid
GBHE-PEG-MIX-705
Section E
Gas-Solid-Liquid
GBHE-PEG-MIX-706
Section F
Solid-Solid
GBHE-PEG-MIX-707
Section G
Gas-Solid
GBHE-PEG-MIX-708
Section H
6.2
Why is it being mixed?
Because a mixture is required
e.g. in paint manufacture
How well does it need to be mixed?
To promote mass transfer
-
To react
is the product spectrum dependent
on the rate of mixing?
Refinery Process Stream Purification Refinery Process Catalysts Troubleshooting Refinery Process Catalyst Start-Up / Shutdown
Activation Reduction In-situ Ex-situ Sulfiding Specializing in Refinery Process Catalyst Performance Evaluation Heat & Mass
Balance Analysis Catalyst Remaining Life Determination Catalyst Deactivation Assessment Catalyst Performance
Characterization Refining & Gas Processing & Petrochemical Industries Catalysts / Process Technology - Hydrogen Catalysts /
Process Technology – Ammonia Catalyst Process Technology - Methanol Catalysts / process Technology – Petrochemicals
Specializing in the Development & Commercialization of New Technology in the Refining & Petrochemical Industries
Web Site: www.GBHEnterprises.com
10. Mass transfer followed by
Reaction
6.3
Which process is rate limiting?
Is it important which is limiting?
How is it to be Mixed?
Batchwise
in an - Agitated Tank
Jet Stirred Tank
Flow Mixer in Loop
Continuously
in an - Agitated Tank
Flow Mixer
Bubble Column
'Semi-batch’
in a - Bubble Column
Two-Phase Agitated Tank
6.4
Is Heat Transfer Important?
Provision of heat transfer surface could determine the size of the equipment. Inline (static) mixers could be incorporated within a shell and tube heat exchanger.
6.5
Is Mixing Time Important?
Reactions are often potentially very rapid and in practical equipment their rates
can be determined by the rate of mixing of the reactants.
6.6
Is Inventory Important?
Nitroglycerine is made in jet mixers to minimize the inventory of unstable
material. Similar considerations could apply to other hazardous (including toxic)
materials.
6.7
Is Subsequent Phase Separation Important?
Mixing intensity (and hence bubble or droplet size) may need to be optimized to
take account of the ease of separation.
Refinery Process Stream Purification Refinery Process Catalysts Troubleshooting Refinery Process Catalyst Start-Up / Shutdown
Activation Reduction In-situ Ex-situ Sulfiding Specializing in Refinery Process Catalyst Performance Evaluation Heat & Mass
Balance Analysis Catalyst Remaining Life Determination Catalyst Deactivation Assessment Catalyst Performance
Characterization Refining & Gas Processing & Petrochemical Industries Catalysts / Process Technology - Hydrogen Catalysts /
Process Technology – Ammonia Catalyst Process Technology - Methanol Catalysts / process Technology – Petrochemicals
Specializing in the Development & Commercialization of New Technology in the Refining & Petrochemical Industries
Web Site: www.GBHEnterprises.com
11. 6.8
What Quantities?
With small quantities simplicity of operation may be the deciding factor while for
large quantities the capital cost may influence the type of equipment to be used.
6.9
What are the Selection Criteria?
Is the choice to be made primarily on economic grounds or is the process
requirements dominant?
6.10
What Data are required?
Apart from those data already listed above, the following are likely to be
important:
Viscosity
is the liquid Newtonian?
Surface Tension or Interfacial Tension is the effect of surfactants
(or surface active impurities) important?
Density
-
Diffusivity
-
Particle size
is size and size distribution important?
Reaction Rate
-
Vapor Liquid Equilibria
-
Liquid-Liquid Equilibria
-
Refinery Process Stream Purification Refinery Process Catalysts Troubleshooting Refinery Process Catalyst Start-Up / Shutdown
Activation Reduction In-situ Ex-situ Sulfiding Specializing in Refinery Process Catalyst Performance Evaluation Heat & Mass
Balance Analysis Catalyst Remaining Life Determination Catalyst Deactivation Assessment Catalyst Performance
Characterization Refining & Gas Processing & Petrochemical Industries Catalysts / Process Technology - Hydrogen Catalysts /
Process Technology – Ammonia Catalyst Process Technology - Methanol Catalysts / process Technology – Petrochemicals
Specializing in the Development & Commercialization of New Technology in the Refining & Petrochemical Industries
Web Site: www.GBHEnterprises.com
12. 7
BASICS
Mixing of fluids is one of the most common operations in chemical processing,
yet also one of the most misunderstood as far as the fundamental mechanisms
are concerned. Design of equipment is based largely on empirical correlations
tempered with experience. For gas-liquid and liquid-liquid contacting, only scaleup relationships exist, as a priori design relationships for real systems are not yet
available even on an empirical basis. Some understanding and quantification of
the basic mechanisms is emerging however (especially for turbulent mixing) and
this is treated later in this Clause. The situation is further complicated by the
other duties a mixer often has to perform (such as heat transfer, chemical
reaction and interphase contacting) and the constraints which may prevail (such
as energy consumption (not often important), fluid inventory and sealing
(important for safety), corrosion, mechanical robustness (especially agitator
shafts), fouling and blockage by solids (e.g. in flow mixers) and foaming). In the
case of chemical reactions the flow pattern in the mixer (backmixed or plug flow,
continuous or batch) is often important also.
It is vital that all such factors as are relevant are taken account of in selection and
design of a mixer. This will often involve several iterations of the design
calculations before the limiting factor is identified. The relative performance of a
device for these duties will depend on the device selected, so several types of
device should be considered initially. Several types of device for each duty are
covered in the subsections of the Guide. The designer should obviously aim for
the most economical design and this will often imply maximizing the rate of the
limiting factor, within the process constraints.
Mixing of liquids takes place by four mechanisms (bulk movement, shear and
elongation, turbulence and molecular diffusion). For example, when a liquid B is
added to a tank containing liquid A, with which it is miscible, it does not disperse
immediately and there is obvious inhomogeneity: all of B is sitting in one part of
the tank. When the stirrer (or jet) is started the liquid begins to move and all of B
tends to move round the tank together. But, because the velocities are not
uniform, B begins to spread out and this spreading continues until B is distributed
all over the tank so that if a large sample of liquid is removed the quantity of B it
contains will be independent of where the sample is taken from. The tank is now
probably well mixed, but this is not necessarily so.
If the flow in the tank is laminar, the close inspection of a small volume will reveal
that there are layers of liquid A separated by layers of liquid B.
Refinery Process Stream Purification Refinery Process Catalysts Troubleshooting Refinery Process Catalyst Start-Up / Shutdown
Activation Reduction In-situ Ex-situ Sulfiding Specializing in Refinery Process Catalyst Performance Evaluation Heat & Mass
Balance Analysis Catalyst Remaining Life Determination Catalyst Deactivation Assessment Catalyst Performance
Characterization Refining & Gas Processing & Petrochemical Industries Catalysts / Process Technology - Hydrogen Catalysts /
Process Technology – Ammonia Catalyst Process Technology - Methanol Catalysts / process Technology – Petrochemicals
Specializing in the Development & Commercialization of New Technology in the Refining & Petrochemical Industries
Web Site: www.GBHEnterprises.com
13. Eventually, the layers of liquid are sheared down to molecular dimensions and
mixing is complete. Shearing down to molecular dimensions is not as difficult as
it sounds: the thickness of the layers has to be halved less than 30 times. In
practice this amount of shearing is rarely necessary because molecular diffusion
spreads the material out of the layers.
If the flow in the vessel is turbulent local mixing is enhanced by eddies, which are
regions of highly sheared fluid which move through the fluid bulk, decaying in
size. They are postulated to decay until they reach a minimum size, the
'Kolmogorov length scale' (Ѵ3/ε)1/4. On length scales below this size, energy is
dissipated by viscous forces only.
The motion on a scale smaller than 32 µm is effectively laminar: thus neutrally
buoyant particles that are appreciably smaller, e.g. 5 µm, will behave as if in a
stagnant liquid. Thus, if they are soluble, the dissolution rate can be calculated
simply by using:
To summarize; the three processes which are present in mixing operations are:
Refinery Process Stream Purification Refinery Process Catalysts Troubleshooting Refinery Process Catalyst Start-Up / Shutdown
Activation Reduction In-situ Ex-situ Sulfiding Specializing in Refinery Process Catalyst Performance Evaluation Heat & Mass
Balance Analysis Catalyst Remaining Life Determination Catalyst Deactivation Assessment Catalyst Performance
Characterization Refining & Gas Processing & Petrochemical Industries Catalysts / Process Technology - Hydrogen Catalysts /
Process Technology – Ammonia Catalyst Process Technology - Methanol Catalysts / process Technology – Petrochemicals
Specializing in the Development & Commercialization of New Technology in the Refining & Petrochemical Industries
Web Site: www.GBHEnterprises.com
14. 7.1
Bulk Movement
The velocity is not uniform so the fluid is spread out by velocity differences and
Distributive Mixing occurs. The fluid is split into different streams, for example at
the agitator in a stirred tank, where one stream goes up and one down, or by an
in-line mixer. Because the travel times are different, the two streams do not
recombine but subsequently mix with other volumes of fluid.
Bulk movement is usually the rate determining process in turbulent mixing
(blending) in tanks as is shown by the fact that mixing times are not significantly
affected by changes in viscosity. It also contributes significantly to mixing in inline mixers. However, it is not of much significance in pipe flow.
In laminar flow, bulk movement is the only flow which occurs and mixing time is
determined by a balance between laminar shear and molecular diffusion, the
former being assisted by distributive mixing effects.
7.2
Shear and Elongation
Shear and elongation arise from bulk movement and are the mechanisms
responsible for spreading out large clumps of fluid.
7.3
Turbulent Diffusion
This is usually the rate determining process in pipe flow, where it is often
modeled by using an effective diffusion coefficient. It is also relevant to mixing in
any turbulent system, especially to mixing in a localized zone of a vessel.
7.4
Molecular Diffusion
This is the ultimate process in all mixing operations, but in turbulent systems
clumps of liquid are usually ground down so rapidly by shear in the eddies that it
is not usually important in determining bulk mixing time. In laminar systems
molecular diffusion can be important. The rates of fast localized reactions can
also be controlled by molecular diffusion.
The foregoing discussion has assumed that the liquids being mixed are miscible
and of similar viscosities (within a factor of 10 or so). In the case of immiscible
liquids the rate limiting process is usually the breakup of droplets and mixing
times are likely to be much longer than those when bulk flow alone is limiting. In
Refinery Process Stream Purification Refinery Process Catalysts Troubleshooting Refinery Process Catalyst Start-Up / Shutdown
Activation Reduction In-situ Ex-situ Sulfiding Specializing in Refinery Process Catalyst Performance Evaluation Heat & Mass
Balance Analysis Catalyst Remaining Life Determination Catalyst Deactivation Assessment Catalyst Performance
Characterization Refining & Gas Processing & Petrochemical Industries Catalysts / Process Technology - Hydrogen Catalysts /
Process Technology – Ammonia Catalyst Process Technology - Methanol Catalysts / process Technology – Petrochemicals
Specializing in the Development & Commercialization of New Technology in the Refining & Petrochemical Industries
Web Site: www.GBHEnterprises.com
15. the case of liquids of differing viscosities the more viscous component often
refuses to join in the bulk flow and mixing times are determined by mass transfer
at the interface between the two liquids.
7.5
Mixing Mechanisms
The requirements of a mixing operation are met by setting up the hydrodynamics
appropriate to the situation, which will involve combinations of bulk flow important
for blending, solid suspension, heat transfer) and shear (for breakup of bubbles,
droplets or particle agglomerates and interphase mass transfer). Figure 1
illustrates broadly the achievable characteristics of various devices in terms of
bulk flow.
FIGURE 1 CHARACTERISTICS OF VARIOUS DEVICES IN TERMS OF BULK
FLOW
For agitators in vessels of given geometry, comparative performance for
producing flow may be judged by comparing FLOW NUMBERS:
Refinery Process Stream Purification Refinery Process Catalysts Troubleshooting Refinery Process Catalyst Start-Up / Shutdown
Activation Reduction In-situ Ex-situ Sulfiding Specializing in Refinery Process Catalyst Performance Evaluation Heat & Mass
Balance Analysis Catalyst Remaining Life Determination Catalyst Deactivation Assessment Catalyst Performance
Characterization Refining & Gas Processing & Petrochemical Industries Catalysts / Process Technology - Hydrogen Catalysts /
Process Technology – Ammonia Catalyst Process Technology - Methanol Catalysts / process Technology – Petrochemicals
Specializing in the Development & Commercialization of New Technology in the Refining & Petrochemical Industries
Web Site: www.GBHEnterprises.com
16. and some idea of comparative performance for shear in turbulent agitation may
be gained by comparing POWER NUMBERS:
Often (e.g. in agitated vessels) flow is required to transport fluid through a
localized high shear region.
Refinery Process Stream Purification Refinery Process Catalysts Troubleshooting Refinery Process Catalyst Start-Up / Shutdown
Activation Reduction In-situ Ex-situ Sulfiding Specializing in Refinery Process Catalyst Performance Evaluation Heat & Mass
Balance Analysis Catalyst Remaining Life Determination Catalyst Deactivation Assessment Catalyst Performance
Characterization Refining & Gas Processing & Petrochemical Industries Catalysts / Process Technology - Hydrogen Catalysts /
Process Technology – Ammonia Catalyst Process Technology - Methanol Catalysts / process Technology – Petrochemicals
Specializing in the Development & Commercialization of New Technology in the Refining & Petrochemical Industries
Web Site: www.GBHEnterprises.com
17. APPENDIX A
A.1
ROTATING MIXING DEVICES
Figure 2 shows a tank and agitator with the key dimensions annotated and
a Table of Typical Ratios of these dimensions. Note that the base may be
either flat or a dished end.
FIGURE 2
TANK LAYOUT
Refinery Process Stream Purification Refinery Process Catalysts Troubleshooting Refinery Process Catalyst Start-Up / Shutdown
Activation Reduction In-situ Ex-situ Sulfiding Specializing in Refinery Process Catalyst Performance Evaluation Heat & Mass
Balance Analysis Catalyst Remaining Life Determination Catalyst Deactivation Assessment Catalyst Performance
Characterization Refining & Gas Processing & Petrochemical Industries Catalysts / Process Technology - Hydrogen Catalysts /
Process Technology – Ammonia Catalyst Process Technology - Methanol Catalysts / process Technology – Petrochemicals
Specializing in the Development & Commercialization of New Technology in the Refining & Petrochemical Industries
Web Site: www.GBHEnterprises.com
18. A.2
Figures 3 to 6 illustrate a variety of different agitators which are generally
used for mixing low viscosity non-Newtonian liquids.
FIGURE 3
PITCHED BLADE TURBINE
Refinery Process Stream Purification Refinery Process Catalysts Troubleshooting Refinery Process Catalyst Start-Up / Shutdown
Activation Reduction In-situ Ex-situ Sulfiding Specializing in Refinery Process Catalyst Performance Evaluation Heat & Mass
Balance Analysis Catalyst Remaining Life Determination Catalyst Deactivation Assessment Catalyst Performance
Characterization Refining & Gas Processing & Petrochemical Industries Catalysts / Process Technology - Hydrogen Catalysts /
Process Technology – Ammonia Catalyst Process Technology - Methanol Catalysts / process Technology – Petrochemicals
Specializing in the Development & Commercialization of New Technology in the Refining & Petrochemical Industries
Web Site: www.GBHEnterprises.com
19. FIGURE 4
DISC TURBINE
FIGURE 5
PROPELLER
Refinery Process Stream Purification Refinery Process Catalysts Troubleshooting Refinery Process Catalyst Start-Up / Shutdown
Activation Reduction In-situ Ex-situ Sulfiding Specializing in Refinery Process Catalyst Performance Evaluation Heat & Mass
Balance Analysis Catalyst Remaining Life Determination Catalyst Deactivation Assessment Catalyst Performance
Characterization Refining & Gas Processing & Petrochemical Industries Catalysts / Process Technology - Hydrogen Catalysts /
Process Technology – Ammonia Catalyst Process Technology - Methanol Catalysts / process Technology – Petrochemicals
Specializing in the Development & Commercialization of New Technology in the Refining & Petrochemical Industries
Web Site: www.GBHEnterprises.com
20. FIGURE 6
A.3
RETREAT CURVED BLADE TURBINE
The agitators shown in Figures 7 to 9 are used primarily in gas-liquid
systems. For the suspension of particulate solids in a liquid, a Marine
Propeller (Figure 5) or a Pitched Blade Turbine (Figure 3) is normally
recommended.
Refinery Process Stream Purification Refinery Process Catalysts Troubleshooting Refinery Process Catalyst Start-Up / Shutdown
Activation Reduction In-situ Ex-situ Sulfiding Specializing in Refinery Process Catalyst Performance Evaluation Heat & Mass
Balance Analysis Catalyst Remaining Life Determination Catalyst Deactivation Assessment Catalyst Performance
Characterization Refining & Gas Processing & Petrochemical Industries Catalysts / Process Technology - Hydrogen Catalysts /
Process Technology – Ammonia Catalyst Process Technology - Methanol Catalysts / process Technology – Petrochemicals
Specializing in the Development & Commercialization of New Technology in the Refining & Petrochemical Industries
Web Site: www.GBHEnterprises.com
21. FIGURE 7
CONCAVE BLADE TURBINE
FIGURE 8
'GASFOIL' AGITATOR
Refinery Process Stream Purification Refinery Process Catalysts Troubleshooting Refinery Process Catalyst Start-Up / Shutdown
Activation Reduction In-situ Ex-situ Sulfiding Specializing in Refinery Process Catalyst Performance Evaluation Heat & Mass
Balance Analysis Catalyst Remaining Life Determination Catalyst Deactivation Assessment Catalyst Performance
Characterization Refining & Gas Processing & Petrochemical Industries Catalysts / Process Technology - Hydrogen Catalysts /
Process Technology – Ammonia Catalyst Process Technology - Methanol Catalysts / process Technology – Petrochemicals
Specializing in the Development & Commercialization of New Technology in the Refining & Petrochemical Industries
Web Site: www.GBHEnterprises.com
22. FIGURE 9
A.4
'HYDROFOIL' AGITATOR
For high viscosity and/or non-Newtonian systems, the selection is often
from those illustrated in Figures 10 to 15.
Refinery Process Stream Purification Refinery Process Catalysts Troubleshooting Refinery Process Catalyst Start-Up / Shutdown
Activation Reduction In-situ Ex-situ Sulfiding Specializing in Refinery Process Catalyst Performance Evaluation Heat & Mass
Balance Analysis Catalyst Remaining Life Determination Catalyst Deactivation Assessment Catalyst Performance
Characterization Refining & Gas Processing & Petrochemical Industries Catalysts / Process Technology - Hydrogen Catalysts /
Process Technology – Ammonia Catalyst Process Technology - Methanol Catalysts / process Technology – Petrochemicals
Specializing in the Development & Commercialization of New Technology in the Refining & Petrochemical Industries
Web Site: www.GBHEnterprises.com
23. FIGURE 10 HELICAL SCREW STIRRER WITH THREE BAFFLES AT 120°
FIGURE 11 HELICAL RIBBON STIRRER
Refinery Process Stream Purification Refinery Process Catalysts Troubleshooting Refinery Process Catalyst Start-Up / Shutdown
Activation Reduction In-situ Ex-situ Sulfiding Specializing in Refinery Process Catalyst Performance Evaluation Heat & Mass
Balance Analysis Catalyst Remaining Life Determination Catalyst Deactivation Assessment Catalyst Performance
Characterization Refining & Gas Processing & Petrochemical Industries Catalysts / Process Technology - Hydrogen Catalysts /
Process Technology – Ammonia Catalyst Process Technology - Methanol Catalysts / process Technology – Petrochemicals
Specializing in the Development & Commercialization of New Technology in the Refining & Petrochemical Industries
Web Site: www.GBHEnterprises.com
24. FIGURE 12 ANCHOR AGITATOR
Refinery Process Stream Purification Refinery Process Catalysts Troubleshooting Refinery Process Catalyst Start-Up / Shutdown
Activation Reduction In-situ Ex-situ Sulfiding Specializing in Refinery Process Catalyst Performance Evaluation Heat & Mass
Balance Analysis Catalyst Remaining Life Determination Catalyst Deactivation Assessment Catalyst Performance
Characterization Refining & Gas Processing & Petrochemical Industries Catalysts / Process Technology - Hydrogen Catalysts /
Process Technology – Ammonia Catalyst Process Technology - Methanol Catalysts / process Technology – Petrochemicals
Specializing in the Development & Commercialization of New Technology in the Refining & Petrochemical Industries
Web Site: www.GBHEnterprises.com
25. FIGURE 13 BENT ANCHOR
FIGURE 14 ”SAWTOOTH” DISC DISPERSER
Refinery Process Stream Purification Refinery Process Catalysts Troubleshooting Refinery Process Catalyst Start-Up / Shutdown
Activation Reduction In-situ Ex-situ Sulfiding Specializing in Refinery Process Catalyst Performance Evaluation Heat & Mass
Balance Analysis Catalyst Remaining Life Determination Catalyst Deactivation Assessment Catalyst Performance
Characterization Refining & Gas Processing & Petrochemical Industries Catalysts / Process Technology - Hydrogen Catalysts /
Process Technology – Ammonia Catalyst Process Technology - Methanol Catalysts / process Technology – Petrochemicals
Specializing in the Development & Commercialization of New Technology in the Refining & Petrochemical Industries
Web Site: www.GBHEnterprises.com
26. FIGURE 15 ”HIGH SHEAR” ROTOR-STATOR MIXER
Refinery Process Stream Purification Refinery Process Catalysts Troubleshooting Refinery Process Catalyst Start-Up / Shutdown
Activation Reduction In-situ Ex-situ Sulfiding Specializing in Refinery Process Catalyst Performance Evaluation Heat & Mass
Balance Analysis Catalyst Remaining Life Determination Catalyst Deactivation Assessment Catalyst Performance
Characterization Refining & Gas Processing & Petrochemical Industries Catalysts / Process Technology - Hydrogen Catalysts /
Process Technology – Ammonia Catalyst Process Technology - Methanol Catalysts / process Technology – Petrochemicals
Specializing in the Development & Commercialization of New Technology in the Refining & Petrochemical Industries
Web Site: www.GBHEnterprises.com
27. APPENDIX B MIXING DEVICES WITHOUT MOVING PARTS
FIGURE 16 COAXIAL JET FLOW MIXER
FIGURE 17 SIDE ENTRY JET FLOW MIXER
FIGURE 18 KENICS STATIC MIXERS
Refinery Process Stream Purification Refinery Process Catalysts Troubleshooting Refinery Process Catalyst Start-Up / Shutdown
Activation Reduction In-situ Ex-situ Sulfiding Specializing in Refinery Process Catalyst Performance Evaluation Heat & Mass
Balance Analysis Catalyst Remaining Life Determination Catalyst Deactivation Assessment Catalyst Performance
Characterization Refining & Gas Processing & Petrochemical Industries Catalysts / Process Technology - Hydrogen Catalysts /
Process Technology – Ammonia Catalyst Process Technology - Methanol Catalysts / process Technology – Petrochemicals
Specializing in the Development & Commercialization of New Technology in the Refining & Petrochemical Industries
Web Site: www.GBHEnterprises.com
28. FIGURE 19 ROSS LLPD MOTIONLESS MIXER
FIGURE 20 SULZER SMV
FIGURE 21 SULZER SMX
Refinery Process Stream Purification Refinery Process Catalysts Troubleshooting Refinery Process Catalyst Start-Up / Shutdown
Activation Reduction In-situ Ex-situ Sulfiding Specializing in Refinery Process Catalyst Performance Evaluation Heat & Mass
Balance Analysis Catalyst Remaining Life Determination Catalyst Deactivation Assessment Catalyst Performance
Characterization Refining & Gas Processing & Petrochemical Industries Catalysts / Process Technology - Hydrogen Catalysts /
Process Technology – Ammonia Catalyst Process Technology - Methanol Catalysts / process Technology – Petrochemicals
Specializing in the Development & Commercialization of New Technology in the Refining & Petrochemical Industries
Web Site: www.GBHEnterprises.com
29. DOCUMENTS REFERRED TO IN THIS PROCESS ENGINEERING GUIDE
This Process Engineering Guide makes reference to the following documents:
ENGINEERING GUIDES
GBHE-PEG-MIX-701
Mixing of Miscible Liquids
(referred to in 6.1 and Table 1)
GBHE-PEG-MIX-702
Gas Mixing
(referred to in 6.1 and Table 1)
GBHE-PEG-MIX-703
Mixing of Solid-Liquid Systems
(referred to in 6.1 and Table 1)
GBHE-PEG-MIX-704
Mixing of Immiscible Liquids
(referred to in 6.1 and Table 1)
GBHE-PEG-MIX-705
Mixing of Gas Liquid Systems
(referred to in 6.1 and Table 1)
GBHE-PEG-MIX-706
Gas-Solid-Liquid Mixing Systems
(referred to in 6.1 and Table 1)
GBHE-PEG-MIX-707
Solids Mixing
(referred to in 6.1)
GBHE-PEG-MIX-708
Gas Solid Mixing
(referred to in 6.1)
GBHE-PEG-MIX-709
'High Shear' Mixers
(referred to in 6.1 and Table 1)
OTHER GBHE DOCUMENTS
GBHE Mixing and Agitation Manual
(referred to in Clause 4 and 4.2).
Refinery Process Stream Purification Refinery Process Catalysts Troubleshooting Refinery Process Catalyst Start-Up / Shutdown
Activation Reduction In-situ Ex-situ Sulfiding Specializing in Refinery Process Catalyst Performance Evaluation Heat & Mass
Balance Analysis Catalyst Remaining Life Determination Catalyst Deactivation Assessment Catalyst Performance
Characterization Refining & Gas Processing & Petrochemical Industries Catalysts / Process Technology - Hydrogen Catalysts /
Process Technology – Ammonia Catalyst Process Technology - Methanol Catalysts / process Technology – Petrochemicals
Specializing in the Development & Commercialization of New Technology in the Refining & Petrochemical Industries
Web Site: www.GBHEnterprises.com
30. Refinery Process Stream Purification Refinery Process Catalysts Troubleshooting Refinery Process Catalyst Start-Up / Shutdown
Activation Reduction In-situ Ex-situ Sulfiding Specializing in Refinery Process Catalyst Performance Evaluation Heat & Mass
Balance Analysis Catalyst Remaining Life Determination Catalyst Deactivation Assessment Catalyst Performance
Characterization Refining & Gas Processing & Petrochemical Industries Catalysts / Process Technology - Hydrogen Catalysts /
Process Technology – Ammonia Catalyst Process Technology - Methanol Catalysts / process Technology – Petrochemicals
Specializing in the Development & Commercialization of New Technology in the Refining & Petrochemical Industries
Web Site: www.GBHEnterprises.com
31. Refinery Process Stream Purification Refinery Process Catalysts Troubleshooting Refinery Process Catalyst Start-Up / Shutdown
Activation Reduction In-situ Ex-situ Sulfiding Specializing in Refinery Process Catalyst Performance Evaluation Heat & Mass
Balance Analysis Catalyst Remaining Life Determination Catalyst Deactivation Assessment Catalyst Performance
Characterization Refining & Gas Processing & Petrochemical Industries Catalysts / Process Technology - Hydrogen Catalysts /
Process Technology – Ammonia Catalyst Process Technology - Methanol Catalysts / process Technology – Petrochemicals
Specializing in the Development & Commercialization of New Technology in the Refining & Petrochemical Industries
Web Site: www.GBHEnterprises.com