The portable VLF Test System 20 kV of Seba KMT can be used to test the cables in conjunction with the according local regulations for operating voltage levels up to 11 kV for new cables and 16 kV for aged cables at 3 μF cable capacity. By using the patented Seba KMT 0.1 Hz Cosine Square Wave Voltage, weak and for further operation critical spots in PE, XLPE but also in paper cables are brought to a controlled breakdown very fast without causing additional damage or ageing to the cable insulation. The SEBS KMT VLF Test System consists of a DC source, which charges the test object up to the required test voltage level and the commutator unit, which performs the regular 5 second interval polarity change. The change-over from one polarity to the reverse one is performed with a switched rectifier, an inductivity (choke) and a capacitor, which is made up of the internal 0.3 μF and the cable capacity itself. The L / C resonance circuit produces a cosine shaped voltage with slopes similar to a 50 Hz sine wave.

1. VLF Test System 20 kV
Portable VLF Test System 20 kV with
0.1 Hz Cosine Square Wave Voltage
Function description:
In accordance with most regulations, cables and joints must be
tested after installation or repair. For this test the breakdown
strength of the cable is tested.
The portable VLF Test System 20 kV of Seba KMT can be used
to test the cables in conjunction with the according local
regulations for operating voltage levels up to 11 kV for new
cables and 16 kV for aged cables at 3 µF cable capacity.
By using the patented Seba KMT 0.1 Hz Cosine Square Wave
Voltage, weak and for further operation critical spots in PE,
XLPE but also in paper cables are brought to a controlled
breakdown very fast without causing additional damage or
ageing to the cable insulation.
The VLF Test System consists of a DC source, which charges
the test object up to the required test voltage level and the
commutator unit, which performs the regular 5 second interval
polarity change.
Technical Data
Output voltage VLF
0 ... 20 kVRMS
The change-over from one polarity to the reverse one is
performed with a switched rectifier, an inductivity (choke) and a
capacitor, which is made up of the internal 0.3 µF and the cable
capacity itself. The L / C resonance circuit produces a cosine
shaped voltage with slopes similar to a 50 Hz sine wave.
Voltage shape
Cosine Square Wave
Change-over slope
approx. 5 ms analogue to
50 Hz AC mains frequency
Frequency
0.1 Hz
Output current
12 mA max.
Technical Features
Display leakage current
0 ... 12 mA (optional)
Display resolution
10 µA
Output voltage DC
0 ... 20 kV
Testable cable capacity
max. 3 µF
Discharge unit
integrated, 10 µF in 3 s
Power supply
Operating temperature
230 V, 50 Hz, approx. 2.5 A
120 V, 60 Hz, approx. 5 A
- 20...+ 40 °C
Weight
< 50 kg, portable
Dimensions (W x H x D)
520 x 600 x 300 mm
The weight of 50 kg make the VLF Test System 20 kV a
powerful, universal and at the same time portable unit.
The patented change over principle in combination with
the recycling of energy stored in the cable capacity
results, in comparison to other methods, in a lower
weight, less energy consumption and much higher test
capacity.
The high test capacity of 3 µF permits the simultaneous
testing of all three phases.
The method is officially recommended by the two VDE
Standards 0276-620 and 0276-621.
Independent researches shows that VLF test is done
most effectively with the 0.1 Hz cosine square wave
shape compared to any other VLF wave shape or
frequency.
VLF is the most economic method for testing PE and
XLPE cables. DC test is not applicable for these cable
types.
controlled output voltage
Options
Breakdown recognition and automatic shut-down.
VLF / DC leakage current measurement.
Scope of Delivery
Basic unit
AC mains cable
Earthing cable 4 m
HV-connection cable 4 m
Accessory bag
Operating manual
PI_VLF20_eng_2004-29.doc
DIN ISO 9001
SebaKMT Vertrieb * 96148 Baunach/Germany Tel. +49-(0) 9544 – 68 – 0 * Fax +49 – (0) 9544 – 2273
E-mail: sales@sebakmt.com * Internet: www.sebakmt.com
CABLE JOINTS, CABLE TERMINATIONS, CABLE GLANDS, CABLE CLEATS
FEEDER PILLARS, FUSE LINKS, ARC FLASH, CABLE ROLLERS, CUT-OUTS
11KV 33KV CABLE JOINTS & CABLE TERMINATIONS
FURSE EARTHING
www.cablejoints.co.uk
Thorne and Derrick UK
Tel 0044 191 490 1547 Fax 0044 191 477 5371
Tel 0044 117 977 4647 Fax 0044 117 9775582
CABLE JOINTS, CABLE TERMINATIONS, CABLE GLANDS, CABLE CLEATS
FEEDER PILLARS, FUSE LINKS, ARC FLASH, CABLE ROLLERS, CUT-OUTS
11KV 33KV CABLE JOINTS & CABLE TERMINATIONS
FURSE EARTHING
www.cablejoints.co.uk
Subject to changes withoutUK
Thorne and Derrick notice
Tel 0044 191 490 1547 Fax 0044 191 477 5371
Tel 0044 117 977 4647 Fax 0044 117 9775582