Martindale Electric Metrohm MET7A501C Safety Insulation Tester - Martindale Electric Metrohm Flash Testers & Insulation Testers

•

0 likes•1,310 views

Metrohm MET7A501C Safety Insulation Tester LV HV Electrical Testing Electrical Safety Testing In Hazardous Areas Martindale Electric Flash Testers & Insulation Testers Martindale Electric Metrohm MET7A501C Safety Insulation Tester Description Martindale Electric Metrohm MET7A501C Safety Insulation Tester was originally designed for use in hazardous areas, such as mines and petrol sites. However, due to the new ATEX regulations, the device no longer meets the requirements for intrinsically safe products - BUT this product has been in active service for 45 years in hazardous areas, in the presence of methane, ammonia and hydrocarbons. The Metrohn MET7A501C is a one of a kind tester and fully meets the ATEX requirements, therefore the use of this tester should be decided upon by a suitably qualified and knowledgeable person. Whilst the MET7A501C safety insuation tester does not qualify for ATEX approval, safety officers should evaluate the risks of failing to perform adequate electrical safety testing. Martindale Electric Metrohm MET7A501C Safety Insulation Tester Specifications Insulation Range: 0 - 50MΩ Test Voltage: 500V DC +/- 10% across 1MΩ Short Circuit Current: <2ma><26mA Continuity Accuracy: +/- 1.6mm of scale arc length Complies With: BS1259 Supply: 1.5V AA IEC batteries Housing: Shatterproof ABS case Dimensions: 32 x 82 x 60mm Weight: 600g approx Operating Temperature: 0 to 40°C Storage Temperature: -20°C to 60°C Martindale Electric Metrohm MET7A501C Safety Insulation Tester Contents Case, test leads (DFK0113) Safety tool to remove battery cover Instruction manual

7A501C safety
insulation tester

The 7A501 has been approved to BS1259 (1958) and
carries the Ministry of Power Certificate Number IS1428
(Class 1)and the Factory Inspectorate Certificate Number
2148 (Class 2A and 2C) which covers Methane, Ammonia
and Hydrocarbons.
The testers have an analogue display and 500V DC
insulation test voltage with a short circuit current of less

SPECIFICATIONS
ELECTRICAL
INSULATION MΩ
Range: 0 - 50M.
Test Voltage: 500V DC±10% across 1MΩ
Short Circuit Current: <2mA
Accuracy: ±1.6mm of scale arc length

than 2mA. On continuity the test voltage is nominally
200mV with a short circuit current of 26mA maximum. A
special allen key is required to access the batteries so
that they may not be changed in a hazardous area.
This tester does not comply with The ATEX94 directive.

NOTE: BS1259 is now obsolescent and has been
superseded by BS5501. Under BS1259 the tester by itself
was approved whereas under BS5501 approvals also
consider applications of the tester.

CONTINUITY Ω
Range: 0 - 50.
Test Voltage: Nominal 200mV
Short Circuit Current: <26mA
Accuracy: ±1.6mm of scale arc length
Battery: 6 off 1.5V AA IEC R6B
MECHANICAL
Size: 132 X 82 X 60mm
Material: ABS
Weight: 0.6kg
Movement: Nominal 1.5mA sensitivity - taut band
Scale Length: 70mm
Test Leads: 1m long with crocodile clips
ENVIRONMENTAL
Operating Temperature: 0 to 40°C
Storage Temperature: -20°C to 60°C

Due to policy of continuous development, Martindale Electric reserves the right to alter equipment specification and description outlined in this document without prior notice. No part of
this document shall be deemed to be part of any contract for the equipment unless specifically referred to as an inclusion within such contract.
© Martindale Electric Co. Ltd. 2005

Martindale Electric Company Ltd.
Metrohm House, Penfold Trading Estate, Imperial Way, Watford, Tel: +44 (0)191 490 1547 01923 441717 Fax: 01923 446900
WD24 4YY. Tel:
Fax: +44 (0)191 477 5371
Email: northernsales@thorneandderrick.co.uk
E-mail: sales@martindale-electric.co.uk Web site: http://www.martindale-electric.co.uk rev2
Website: www.cablejoints.co.uk
www.thorneanderrick.co.uk

Martindale Electric owns Metrohm low voltage products. The Martindale Electric product range helps electricians and maintenance engineers carry out portable appliance testing, check fixed wiring and safely prove dead. Martindale Electric has always been a pioneer in test equipment. Martindale Electric firsts include: The first ever socket tester The first safety insulation tester The first self proving non-contact voltage indicator The first low cost fuse finder The first non-trip, no battery, no test button, loop tester displaying PE, PN PFC & PSC The first handheld insulation tester with polarisation index The first advanced socket tester, as defined by the Health and Safety Executive The smallest and lightest handheld PAT Tester

SEBA KMT Cable Fault Locators, Surge Generators (Thumpers) - SEBA KMT Cable F...

Thorne & Derrick International

Surge wave generators (SWG) are used with reflectometers for cable fault location. They generate surges that create arcs at faults, allowing transient waves to be recorded and fault distances to be determined. SWGs are available for voltages up to 3500kV and energies up to 3500J. They use switchable capacitors and surge stages to optimize energy for prelocation and pinpointing faults. A Digiphone receiver uses the difference in arrival time between electromagnetic and acoustic signals to precisely locate faults.

Megger dc insulation resistance testers -seminario

Cesar Enrique Gutierrez Candia

The document provides information on new insulation resistance testers from Megger, including the MIT515, MIT525, MIT1025, S1-568, and S1-1068 models. It discusses the features and benefits of the new models compared to previous versions, such as increased noise immunity, faster charge times, remote operation via Bluetooth or USB, and improved safety. The document also outlines how the different models are suited to various applications and customer types, with the MIT series targeted towards industrial users and the S1 series aimed at utilities and service companies operating in noisier environments.

Seaward KD1E High Voltage HV Indicators & Detectors, Phasing Units, Ammeters ...

Thorne & Derrick International

This document provides information about electrical test equipment from Seaward Group, including: - Low voltage and high voltage test tools for electrical installations from distribution cables to plug sockets. - Multi-function and single-function installation testers, high voltage indicators, proving units, and accessories. - Details on specific products like the PowerTest 1557 multi-function installation tester, IRT 1557 insulation and continuity tester, ERT 1557 earth resistance tester, and PowerCheck 1557 verification unit. - Seaward offers over 70 years of experience in electrical test instrumentation and provides a complete testing and measurement solution with service, calibration, and support.

SEBA KMT Teleflex TDR Fault Locator for LV-HV Low Resistance Cable Faults

Thorne & Derrick International

SEBA KMT Teleflex T30E is a digital TDR for the fault location of low resistance cable faults and interruptions in low and high voltage power cable networks. With integrated battery power supply Teleflex T30E is ideally suited for field fault location use - can be connected to a shock discharge generator and an ARM filter for pre-location of high resistance and intermittent cable faults. SEBA KMT Teleflex T30E - Features : One button operation, "Quick-Step" mode for rapid fault finding, Automatic far end indication and fault reconition with distance indication, Impulse current and voltage decay method, Zoom function, "Step-by-Step" easy mode for user friendly location of cable faults.

Baur - Cable Fault Locators & Location Specialists (LV MV HV Cables)

Thorne & Derrick International

Cable Fault Location Instrument - Street Lighting - SEBA KMT Digiflex

Thorne & Derrick International

The Digiflex Com is a compact and efficient reflectometer that can: Detect faults and measure lengths of metallic telecommunications and power cables with a high resolution of 2.5 cm. It features a simple and clearly structured display, voltage-protected inputs up to 250V, and a measuring range from 5m to 30km. Reflectometers like the Digiflex Com work by transmitting electrical pulses into cables and calculating distances based on the time between the pulse transmission and any reflections.

Martindale Electric Metrohm METE3640 4kV Flash Tester - Martindale Electric M...

Thorne & Derrick International

Metrohm METE3640 4kV Flash Tester LV HV Electrical Testing Digital Flash Tester Martindale Electric Flash Testers & Insulation Testers Martindale Electric Metrohm METE3640 4kV Flash Tester Description The Metrohm E3640 is a 4kV AC flash tester is capable of operating from either a 115V or 230V supply, at 50 or 60Hz. the Metrohm E3640 has a twin 3 1/2 digit LCD display which shows both output voltage and leakage current. The Metrohm flash tester device is built into a robust carry case, making it easily portable. The Metrohm E3640 is a 4kV AC flash tester has three modes of operation, where the fail lamp on the E3640 illuminates and a buzzer will sound: 1. Trip: will trip when a pre-determined current is exceeded 2. Breakdown: fast transients can trigger the trip 3. Burn: where the trip function is by-passed and the fault current flows continuously to expose the fault Martindale Electric Metrohm METE3640 4kV Flash Tester Specifications Power Requirement: 115 / 230V +/- 15%, 50/60Hz, 40VA Fuses: 230V: 5 x 20mm 0.25A, HBC, Type F 115V: 5 x 20mm 0.5A, HBC, Type F Output Voltage Range: 0 - 2.2, 0 - 4.2kV 50 / 60Hz AC Accuracy: +/- 2% of reading +/- 1 digit Leakage Current: 0 - 5mA (nominal), 50 / 60Hz in 10µA steps Accuracy: +/- 2% reading, +/- 1 digit Trip Level Range: 0 to 3mA 50 / 60Hz Setting Accuracy: +/- 5% of full range Trip Response Leakage: Will trip for fault duration >5mS but not for <100µS Breakdown: Will trip for fast transients of 30µS and above Complies with: EMC to BS EN 50081-1 & BS EN 50082-2 Safety & Flash Test: BS EN 61010-1 Dimensions: 330 x 263 x 144mm Weight: 4kg approx Martindale Electric Metrohm METE3640 4kV Flash Tester Contents Metrohm METE3640 4kV Flash Tester Flash gun Earth lead Mains power lead Instruction manual

The document summarizes the specifications of various continuity and insulation measurement devices: - The CP-100C continuity tester measures resistance from 0-120 ohms with currents of 200mA or 20mA, and has programmable conformity thresholds of 1 or 2 ohms. It is IEC 61557-4 compliant. - The CP-100B insulation measurement unit measures resistance from 10kohms to 999Mohms with configurable voltages from 50-1000VDC and a measuring current of at least 1mA. It has adjustable conformity thresholds and complies with IEC 61557-2. - When used together, the CP-100C tester can display insulation readings on its screen while housed in

SebKMT Cable Sheath testers & Fault Locators

Thorne & Derrick International

Thorne & Derrick UK are official distributors of the SebaKMT range of LV-HV Cable Fault Location instruments including cable sheath testers and cable sheath fault prelocation and pinpointing units. SebaKMT are the leading manufacturer of measurement equipment for the diagnosis of cable networks and for cable fault location. Cable faults are the ''natural enemy'' of reliability. The innovative SebaKMT products make it possible to quickly localise low and high voltage cable faults without causing damage to fault-free parts of the cable.

Ingaas 200um apd to can

Vivi Anita

This document provides specifications for a 200um InGaAs APD photodiode in a TO-CAN package. It has high sensitivity and low capacitance, making it suitable for telecommunications applications. Key parameters include an active diameter of 200um, wavelength detection range of 1100-1650nm, and maximum breakdown voltage and dark current of 60V and 6nA respectively. Dimensional outlines and pin assignments are also provided.

SEBA KMT High Voltage VLF Cable Testers Up To 20kV - SEBA KMT Cable Testers &...

Thorne & Derrick International

The portable VLF Test System 20 kV of Seba KMT can be used to test the cables in conjunction with the according local regulations for operating voltage levels up to 11 kV for new cables and 16 kV for aged cables at 3 μF cable capacity. By using the patented Seba KMT 0.1 Hz Cosine Square Wave Voltage, weak and for further operation critical spots in PE, XLPE but also in paper cables are brought to a controlled breakdown very fast without causing additional damage or ageing to the cable insulation. The SEBA KMT VLF Test System consists of a DC source, which charges the test object up to the required test voltage level and the commutator unit, which performs the regular 5 second interval polarity change.

farady 15kv pole mounted auto circuit breaker

AUTO RECLOSER

Farady Electric produces pole mounted auto circuit reclosers for overhead power distribution. The FAR-15 series reclosers can be used on distribution lines from 11kV to 38kV, with rated currents up to 1600A. They integrate control, protection, measurement, communication, fault detection and online monitoring functions. The reclosers use epoxy resin insulation and magnetic actuators for long life in harsh environments from -45°C to 85°C. They offer options for voltage, current, breaking capacity, installation style, protection curves, communication protocols and measurement functions.

Megger Cable Fault Locators - Power Cable Fault Locators, Van mountable Solut...

Thorne & Derrick International

Cable fault location has often been seen as a dark art, as the causes of faults are different and varied. Successfully locating faults locations depends on an experienced operator. The challenge to Megger’s engineering team was to remove the mysteries from fault locating, and to make the whole process more logical. This methodical approach was used to define a feature set that would satisfy fault location needs in the varied conditions where the tester would be used around the world. Megger cable fault location solutions include : low voltage TDR underground cable fault locators, surge generator fault locators, cable fault pinpointing, high voltage DC test sets and high voltage (11kV-33kV-66kV-132kV) underground cable fault locators.

Pfisterer Electrical Safety Equipment - Voltage Detectors, Phase Comparators,...

Thorne & Derrick International

Megger TDR

Niroj Bhujel

The Megger TDR2000/3 is a dual channel time domain reflectometer for locating faults on paired metallic cables. It has a minimum resolution of 0.1m and a maximum range of 20km depending on the cable type and velocity factor selected. It has five output impedances and an auto impedance matching feature. The TDR2000/3 can identify faults through reflected pulses which indicate issues like open conductors, shorts, joints or splits in the cable. It stores up to 100 traces internally and can upload data via USB to the TraceXpert software for additional analysis and reporting of cable test results.

Seaward Catalogue

Thorne & Derrick International

Seaward has over 70 years experience in the design manufacture of market-leading electrical test equipment. Seaward’s unrivalled range of electrical test equipment serves a wide variety of safety testing and precision measurement applications. For 25 years Seaward has been developing market-defining portable appliance testers, software and accessories for the PAT testing market. The Cropico and Clare ranges of precision instruments and industrial electrical test equipment bolster Seaward’s product offering and demonstrate the result of 70 years of technical expertise across a number of industries including manufacturing, utilities and aerospace. The all-inclusive Seaward electrical test equipment range now encompasses: PAT Testing Installation Testing Electrical Test Tools High Voltage Testing Industrial Testing and Measurement Micro Ohmmeters Hipot Testers Resistance Standards Decade Boxes

Insulation Resistance Testing / Megger

Roland Manansala

The document discusses insulation resistance testing (IRT), also known as megger testing. IRT determines the electrical integrity of wires by identifying faulty wires. Faulty electrical wiring is a major cause of fires. The document also lists several commercial and residential clients that the author has performed IRT or megger testing for at their properties located in Metro Manila and nearby provinces.

Seaward Type L Plus Large Jaw High Voltage HV Clamp Meter

Thorne & Derrick International

The Type L Plus is a large jaw current clamp meter that can measure currents up to 2000 amps. It has a 100mm jaw opening allowing measurement of large conductors and fuse carriers. The clamp provides continuous readout of current values on its large LCD display and can store maximum demand readings. It is designed for safety with high insulation levels and is supplied with a carry case and instructions.

Seaward KD1E-15D Digital High Voltage 15kV Indicator & Voltage Detector

Thorne & Derrick International

The document describes high voltage indicators for confirming the presence of voltage on earthed neutral electrical systems. It provides details on different models of indicators, including neon and digital versions, that feature encapsulated resistor chains and safety standards compliance. Accessories like proving units and extension rods are also described to ensure the indicators work properly and can be used on various equipment. Technical specifications are given on the voltage ranges, currents, lengths and other attributes of the different indicator units.

Datasheet CaP COL

GiovanniPugliese

Electrical test and measurement megger

Jost's Engineering Company Limited

CATU Voltage Tester For MV Separable Connectors (10-36kV)

Thorne & Derrick International

This document provides information on various MV substation equipment and voltage detection systems, including: 1. VPIS and VDS systems that indicate the voltage presence on MV cubicles by being installed on capacitive dividers and having a 4mm standard socket for voltage indication. 2. A separable voltage detecting system (VDS) that enables checking the absence or presence of voltage on three phases with high impedance and a maximum voltage of 1080V, indicating voltage with a red flashing LED. 3. A voltage tester for MV separable connectors that checks the absence of voltage on capacitive terminals, has a sensor to remove and replace insulating covers, and signals via beeping and red LEDs, powered by

Cable Detection Tools - Cable Detection Tools - Cable Detection EZICAT

Thorne & Derrick International

The document describes the EziSystem cable avoidance tools, including the EziCAT 100 and EziCAT 200 locators and the EziTrace signal generator. It highlights issues with manually adjusted cable locators, such as missing services due to incorrectly adjusted settings. The EziSystem aims to reduce this risk of human error by automatically setting the EziCATs to full sensitivity mode for initial detection and allowing simple selection of detection modes.

M4100

Manuel Verdugo

The M4100 is the world's premier power apparatus and insulation test instrument. It has unique test capabilities and AI analysis software making it the most trusted instrument in the power industry. These instruments are used globally thanks to comprehensive testing options, safety features, and measurement accuracy. The latest 4th generation M4100 has improved ruggedness, accuracy, universal controller compatibility, expanded software, and safety features.

Pfisterer KP-Test 5 Voltage Detectors

Thorne & Derrick International

The document provides information on several voltage detector models from Pfisterer, including the KP-Test 5, KP-Test 5 dual, KP-Test 5L, KP-Test 5L dual, KP-Test 5H, and KP-Test 5HL. The detectors can be used for medium and high voltage applications from 3 kV to 420 kV. They indicate the presence of operating voltage when a conductor is contacted and have features that maximize safety, reliability, and usability.

Datasheet Fluke 113. Hubungi PT. Siwali Swantika 021-45850618

PT. Siwali Swantika

Catu Electrical - Low & High Voltage Electrical Safety Equipment For Undergro...

Thorne & Derrick International

CATU are world-market leaders in Electrical Safety Equipment for LV-HV Substation, Switchgear and Overhead Line projects and maintenance. T&D are CATU's largest UK distributor of Electrical Safety Equipment. Catu insulating gloves provide high dielectric performance for LV-HV cable jointing, live-line, substation, overhead and underground cable installations - insulating gloves protect against electrical shock. Catu Arc Flash Clothing & Protection Kits for working on LV-HV switchgear, cables and "racking-in and racking-out" of circuit breakers. Catu Life Saving & Accident Intervention Kits are designed to make all necessary electrical safety equipment on-hand for rapid intervention and rescue up to 33kV. Catu Kits include rescue stick, voltage detector, insulated cable cutting tool, insulating platform, rescue hook, insulating gloves and boots - mobile and wall-mounted substation kits. Catu Short Circuiting & Earthing Kits suit overhead transmission and distribution lines, substation busbars, rail electrification, transformer and switchgear applications. Short Circuiting and Portable Earthing Kits are available with a choice of earth clamps for both live and earth end in accordance with UK DNO, Network Rail and National Grid specifications - customised earthing kits to order. Catu voltage detectors and phase comparators for voltage detection and integrity testing on LV-HV electricity transmission, distribution and overhead lines and cables.

WT Henley 54141-03 House Service Cutouts - Series 6, 60/80Amp, Single Pole

Thorne & Derrick International

The document describes a range of underground fuse service equipment called Series 6 House Service Cut-outs that are used for 240/415V power distribution systems. The cut-outs come in single-pole, single-pole-and-neutral, and triple-pole configurations up to 100A. They have securely mounted terminal screws and serrated terminals that accommodate various conductor sizes. The cut-outs can be connected together via an insulated busbar for safe and quick installation.

Clifford & Snell - Yodac V4 Beacon, Hazardous Area ATEX Zone 1 & 2 Beacons (...

Thorne & Derrick International

This document summarizes an intrinsically safe LED status beacon that is: 1) BASEEFA (ATEX) approved for use in hazardous zones, with up to 4 modules in combinations of lens colors like red, amber, green, opal, blue, or clear. 2) Rated for continuous use with high light intensity and a long life LED design. 3) Simple to install with a reliable, flame retardant ABS plastic enclosure that is also anti-static.

What's hot

CATU C Diag Touch Continuity Tester

Thorne & Derrick International

SebKMT Cable Sheath testers & Fault Locators

Thorne & Derrick International

Ingaas 200um apd to can

Vivi Anita

SEBA KMT High Voltage VLF Cable Testers Up To 20kV - SEBA KMT Cable Testers &...

Thorne & Derrick International

farady 15kv pole mounted auto circuit breaker

AUTO RECLOSER

Megger Cable Fault Locators - Power Cable Fault Locators, Van mountable Solut...

Thorne & Derrick International

Pfisterer Electrical Safety Equipment - Voltage Detectors, Phase Comparators,...

Thorne & Derrick International

Megger TDR

Niroj Bhujel

Seaward Catalogue

Thorne & Derrick International

Insulation Resistance Testing / Megger

Roland Manansala

Seaward Type L Plus Large Jaw High Voltage HV Clamp Meter

Thorne & Derrick International

Seaward KD1E-15D Digital High Voltage 15kV Indicator & Voltage Detector

Thorne & Derrick International

Datasheet CaP COL

GiovanniPugliese

Electrical test and measurement megger

Jost's Engineering Company Limited

CATU Voltage Tester For MV Separable Connectors (10-36kV)

Thorne & Derrick International

Cable Detection Tools - Cable Detection Tools - Cable Detection EZICAT

Thorne & Derrick International

M4100

Manuel Verdugo

Pfisterer KP-Test 5 Voltage Detectors

Thorne & Derrick International

Datasheet Fluke 113. Hubungi PT. Siwali Swantika 021-45850618

PT. Siwali Swantika

What's hot (19)

CATU C Diag Touch Continuity Tester

SebKMT Cable Sheath testers & Fault Locators

Ingaas 200um apd to can

SEBA KMT High Voltage VLF Cable Testers Up To 20kV - SEBA KMT Cable Testers &...

farady 15kv pole mounted auto circuit breaker

Megger Cable Fault Locators - Power Cable Fault Locators, Van mountable Solut...

Pfisterer Electrical Safety Equipment - Voltage Detectors, Phase Comparators,...

Megger TDR

Seaward Catalogue

Insulation Resistance Testing / Megger

Seaward Type L Plus Large Jaw High Voltage HV Clamp Meter

Seaward KD1E-15D Digital High Voltage 15kV Indicator & Voltage Detector

Datasheet CaP COL

Electrical test and measurement megger

CATU Voltage Tester For MV Separable Connectors (10-36kV)

Cable Detection Tools - Cable Detection Tools - Cable Detection EZICAT

M4100

Pfisterer KP-Test 5 Voltage Detectors

Datasheet Fluke 113. Hubungi PT. Siwali Swantika 021-45850618

Viewers also liked

Catu Electrical - Low & High Voltage Electrical Safety Equipment For Undergro...

Thorne & Derrick International

WT Henley 54141-03 House Service Cutouts - Series 6, 60/80Amp, Single Pole

Thorne & Derrick International

Clifford & Snell - Yodac V4 Beacon, Hazardous Area ATEX Zone 1 & 2 Beacons (...

Thorne & Derrick International

Wolf Turbolites - Spec Sheet

Thorne & Derrick International

The Turbolite is a high powered compressed air lamp certified for use in hazardous areas like oil and gas facilities. It provides safer lighting than low voltage options in wet and flammable gas conditions. The A-TL44 model has an all-round bay light, while the A-TL45 has a reflector head for direct or wide-angle illumination. Both have spark-free brass casings and are designed for harsh industrial use. They require a clean, dry compressed air supply to operate efficiently and prevent lens contamination.

3M Cold Shrink QT-III Silicone Rubber Outdoor Cable Terminations 7600S - Sele...

Thorne & Derrick International

This document provides a selection guide for 7600-S-3W Series cable insulation kits. It lists the kit numbers, insulation diameters and thickness they are compatible with, voltage ratings, and applicable wire gauges. Kits are available for cable insulation ratings of 3.3-35kV and wire gauges ranging from 8-1000mm2 or AWG 6-500. The determining factor for kit selection is the cable insulation diameter, with allowance for shielding thickness.

Fluke Corportation Catalogue - PAT Portable Appliance Testers, Clamp Meters, ...

Thorne & Derrick International

This document provides a catalog of test tools and accessories from Fluke including: - Digital multimeters - Thermal imagers - Digital thermometers - Installation testers/portable appliance testers - Insulation testers/earth ground testers - Clamp meters and electrical testers - ScopeMeter test tools - Power quality tools - Field calibrators - Indoor air quality tools - Laser distance meters - Vibration tester - Radiation meter - General accessories It also advertises new products from Fluke and combo kits that bundle multiple tools together.

Seaward - Electrical Testing & Voltage Detection, High Voltage Safety, HV Ind...

Thorne & Derrick International

The PrimeTest 350 is an advanced portable appliance tester (PAT) designed for professionals. It features a lightweight, handheld design with rechargeable batteries and wireless Bluetooth connectivity. The PrimeTest 350 can perform a wide range of electrical safety tests and store results internally or transfer them wirelessly to external printers, scanners, and PAT testing software for record keeping. It is part of Seaward's PATSolutions package which provides a complete portable appliance testing system including the tester, accessories, software, and support.

Cembre Hydraulic Cable Cutters and Cable Cutting Tools

Thorne & Derrick International

Cembre Cable Cutters & Cutting Tools - UK Distributor Manual, Ratchet, Hydraulic, Battery Cable Cutting Tools Cembre cable cutters are ideal for cutting low and high voltage power, control and instrumentation cablesincluding steel wire armoured (SWA) cables. Cembre hydraulic cable cutters also include ranges for overhead line conductor cutting applications - ABC (Aerial Bundled Conductor), AAAC (All Aluminium Alloy Conductor), ASCR (Aluminium Conductor Steel Reinforced) and copper overhead lines. Cable cutters suit up to 4 core 400sqmm XLPE/SWA BS5467 cables, lead covered sheathed cables and all high voltage power cables including Triplex. Cembre Hydraulic Cable Cutters Cembre Hydraulic Cable Cutters and Cable Cutting Tools - Features : Hand operated Cembre hydraulic cutter tools designed to cut copper, aluminium and telecommunications cables, up to 85mm diameters Double speed Cembre cable cutting action : a fast advancing speed for rapid approach of the blades to the cable and a slower more powerful speed for cable cutting Cembre cable cutting blades are made from high strength special steel, heat trated to ensure a long service life Cembre hydraulic cable cutting tool heads can be easily opened to allow the cutting of running cables Cembe hydraulic cable cutting tools can be rotated through 90, 180 and 320 degrees to allow the cable jointer or electrical engineer to cut cables in the most accessible position

CATU Insulating Rubber Gloves - Rubber Latex Gloves, Composite Gloves & Arc F...

Thorne & Derrick International

There are 2 main types of insulating gloves i) Latex Gloves provide high dielectric performance and must be used with leather overgloves for mechanical protection, ii) Composite Gloves provide superior mechanical protection against punctures and tears eliminating the need for overgloves. Wearing suitable PPE to protect electrical engineers, cable jointers and linesmen against dangers posed by exposure to electric cables and circuits is essential. Insulating gloves must be flexible and durable with high dielectric strength compliant with IEC 60903. Insulating rubber gloves conform to IEC 60903 standard. IEC 60903 standard insulating rubber gloves are subject to dielectrical, mechanical resistance and ageing tests - composite and rubber insulating gloves are available to prevent against electric shock hazards. Insulating gloves are used by LV-HV cable jointers, electrical engineers and overhead linesmen and are approved by UK utilities including EDF Energy. Typical applications include : low voltage and live-working up to 1kV (Class 0 Insulating Gloves), live line working on overhead lines (Class 1, 2, 3, 4 Insulating Gloves), electrical switching and also when operating underground moling machines.

Salisbury Arc Flash Protection Clothing & Kits - Arc Flash Hood, Arc Flash Co...

Thorne & Derrick International

This document provides sizing charts and product information for Salisbury arc flash protection clothing and kits. It includes sizing charts for coats, bib overalls, coveralls and hoods. Material weights are provided for different ATPV ratings. Product numbers are explained to identify the item, size, ATPV rating and other features. Features of coats, bib overalls and hoods are described along with their intended ATPV ratings and certifications.

Viewers also liked (10)

Catu Electrical - Low & High Voltage Electrical Safety Equipment For Undergro...

WT Henley 54141-03 House Service Cutouts - Series 6, 60/80Amp, Single Pole

Clifford & Snell - Yodac V4 Beacon, Hazardous Area ATEX Zone 1 & 2 Beacons (...

Wolf Turbolites - Spec Sheet

3M Cold Shrink QT-III Silicone Rubber Outdoor Cable Terminations 7600S - Sele...

Fluke Corportation Catalogue - PAT Portable Appliance Testers, Clamp Meters, ...

Seaward - Electrical Testing & Voltage Detection, High Voltage Safety, HV Ind...

Cembre Hydraulic Cable Cutters and Cable Cutting Tools

CATU Insulating Rubber Gloves - Rubber Latex Gloves, Composite Gloves & Arc F...

Salisbury Arc Flash Protection Clothing & Kits - Arc Flash Hood, Arc Flash Co...

Similar to Martindale Electric Metrohm MET7A501C Safety Insulation Tester - Martindale Electric Metrohm Flash Testers & Insulation Testers

Datasheet Metrel MI 3250. Hubungi PT. Siwali Swantika 021-45850618

PT. Siwali Swantika

Martindale Electric Metrohm METE3511 5kV Analogue Insulation Tester - Martind...

Thorne & Derrick International

Metrohm METE3511 5kV Analogue Insulation Tester LV HV Electrical Testing Insulation Resistance Measurement Martindale Electric Flash Testers & Insulation Testers Martindale Electric Metrohm METE3511 5kV Analogue Insulation Tester Description The Martindale Electric Metrohm E3511 5kV analogue insulation tester has both battery and mains operation. The Metrohm E3511 measures insulation from 100kΩ to 100GΩ, with 4 selectable DC test voltages (500V, 1kV, 2.5kV & 5kV). The E3511 has a large analogue scale which also displays AC or DC voltage up to 1000V. A latching test switch also allows hands-free testing on the Metrohm insulation tester. The Metrohm E3511 5kV analogue insulation tester offers a full over-voltage and over-current protection for measurements, with 14 - 16 hours operation from re-chargeable NiMH batteries. The Metrohm insulation unit is supplied in a rugged carry case with an accessory case that clips to the lid and will carry the supplied test leads and manual. Martindale Electric Metrohm METE3511 5kV Analogue Insulation Tester Specifications Insulation Resistance Range: 100kΩ to 100GΩ Insulation Range Accuracy: +/- 1.5% of scale length Insulation Range Temperature Coefficient: <0.04% /><10v><10MΩ Housing: Yellow ABS, black polycarbonate Dimensions: 330 x 263 x 144mm Weight: 4.2kg approx Martindale Electric Metrohm METE3511 5kV Analogue Insulation Tester Contents Metrohm E3511 5kV analogue insulation tester 2m Test leads Carrying case Crocodile Clips Accessory bag Re-chargeable NiMH batteries Instructions manual

2 u 650w single power supply

kimminsu0216

This document provides specifications for an EPS2U 650W power supply model EP2A5651A-B. It includes details on the power supply's input/output electrical specifications, environmental requirements, safety certifications, and labeling. The power supply has an input voltage range of 90-264VAC and can provide up to 650W of continuous power on its regulated outputs of +3.3V, +5V, +12V, -12V and +5VSB. It meets various EMI and safety standards and is rated to operate from 0-50°C with 5-95% humidity.

Data Teknis Gossen Metrawatt Ohmmeter : METRAOHM 413

PT. Siwali Swantika

Data Teknis Gossen Metrawatt Insulation Tester METRISO PRO

PT. Siwali Swantika

Uniohm resistors datasheet for car -anti-sulfurized thick film chip resistors...

Felix Law

This Uniohm resistors datasheet for car 1%-5%, anti-sulfurized thick film chip resistors, ns02~ns12 series. Allchips is the authorized distributor of Uniohm. UNIOHM recommend the storage condition temperature: 15℃~35℃, humidity :25%~75%. (Put condition for individual product). Even under UNIOHM recommended storage condition, solderability of products over 1 year old. (Put condition for each product) may be degraded. Store / transport cartons in the correct direction, which is indicated on a carton as a symbol. Otherwise bent leads may occur due to excessive stress applied when dropping of a carton. Product performance and soldered connections may deteriorate if the products are stored in the following places: a. Storage in high Electrostatic. b. Storage in direct sunshine、rain and snow or condensation.

Imegger, mit 4002, cat iv insulation tester 1000 v, op 54

Dalian Zero Instrument Technology Co., Ltd China

MIT400/2 CAT IV Insulation testers ■ Designed for Electrical and Industrial testing ■ Insulation testing up to 1000 V and 200 GΩ range ■ Stabilised insulation test voltage (New) ■ Single range, faster continuity testing from 0.01 Ω to 1 MΩ (New) ■ Adjustable insulation test voltage from 100V to 1000V (New) ■ 600 V Trms AC and DC voltage measurement ■ Test result storage and Bluetooth® downloading ■ Live circuit detection and protection ■ Rechargeable options for mains and car charging (New) ■ CAT IV 600 V and IP54

Data Teknis Gossen Metrawatt Battery Tester : METRACELL - BT PRO

PT. Siwali Swantika

350kV 8000KVA series resonant cable test system

Johnny Chan

This document provides the technical specifications for an AC resonant test system for testing cables up to 220kV. The system has a rated power of 8,000 kVA at 350 kV and can test large cable reels up to 600 meters long. It includes components such as an LV switchgear, voltage regulator, exciter transformer, HV reactor, and HV filter to form a resonant test loop that meets standards for voltage withstand and partial discharge testing of high voltage cables.

Data Teknis Gossen Metrawatt Insulation Tester METRISO 1000A

PT. Siwali Swantika

METRISO 1000A Insulation Tester

Dalian Zero Instrument Technology Co., Ltd China

This insulation tester can measure insulation resistance at voltages up to 1000V, and test earth conductors, protective conductors, and bonding conductors. It provides quick testing with a signal lamp indicator and can also measure low impedance from 0 to 4 ohms. The device operates on batteries, measures voltage up to 1000V, and has a long battery life due to powering on only during measurements.

Data Teknis Gossen Metrawatt Multimeter : METRAport 3A

PT. Siwali Swantika

This document provides information on the METRAport 3A Folding Analog Multimeter. It has the following key features and specifications: - It is a portable analog multimeter that can fold closed, with 46 measuring ranges for voltage, current, resistance, and dB. - It has a rugged design for harsh environments and provides protection for the measuring device and display when folded. - Measurement functions include 9 voltage ranges up to 600V, 7 current ranges up to 10A, 5 resistance ranges up to 20MΩ, and 9 level ranges from -40 to +62 dB. - It meets safety standards IEC 61010-1 and EN 61010-1 and has protection from over

Delta drp024 power_supply_catalog

Electromate

This document provides specifications for a 120W DIN rail power supply with the following key details: - It has a single 120W output with a voltage range of 22-28V and a current of 5A. - The input voltage range is 85-264VAC. It has protections such as overload, overvoltage, and overtemperature protections. - Additional features include compact design, easy wire connection, 10 year lifetime, shock/vibration resistance, and convection cooling.

SEBA KMT MFM5 1 Cable Sheath Testing, Fault Prelocation & Pinpointing

Thorne & Derrick International

SEBA KMT MFM5-1 is the universal test instrument for cable sheath testing including prelocation and pinpointing of cable sheath faults - in sheath testing mode SEBA KMT MFM5-1 can detect minute cable sheath insulation damage on low and high voltage cable networks. SEBA KMT MFM5-1 ensures fast and precise cable sheath fault location - the instrument is menu-driven and fully automatic sheath fault prelocation is accurately achieved by inputting total cable length. SEBA KMT ESG 80-2 can be combined with the MFM5-1 for earth fault location in LV-HV cables. Cable Sheath Test & Fault Location SEBA KMT MFM5-1 Features : Sheath testing, fault prelocation and pinpointing combined in single unit, sheath testing up to 5kV, time saving prelocation of sheath fault.

60 Monocrystalline Cell Modules and 72 Mono Crystalline Cell Modules:

Emmvee India

60 Monocrystalline Cell Modules: The 60 cell monocrystalline modules are well suited for those solar products that require optimum power efficiency but with less amount of cells. The Monocrystalline module is specifically designed to match the performance needs of a certain solar application. Some of its features can be seen as follows: 1. The low weight of just 18 kgs makes it an ergonomic module to use. 2. A 3.2 mm high transmission tempered glass that takes the overall performance of this module to a new high. 3. Effective tackling of weather conditions such as a strong hail with resistance to speed up to 83 km/h so that your device is not damaged. 4. Excellent operating temperature range. 5. Class II protection so that the user gets at least two layers of insulation from unintended damage to the equipment 72 Mono Crystalline Cell Modules: The Monocrystalline modules can be used where discrete but powerful performance is required. The modules are designed in accordance with the specific need for a particular solar product out there. Some of its salient features are listed below: 1. Effective tackling of weather conditions such as a strong hail with resistance to speed up to 83 km/h so that your device is not damaged. 2. Excellent operating temperature range. 3. Optimum yield even in fluctuating voltages and current. 4. A 3.2 mm high transmission tempered glass that takes the overall performance of this module to a new high. 5. The material used in the construction can sustain adverse conditions like excessive sun exposure, heavy rainfall etc. 6. Class II protection so that the user gets at least two layers of insulation from unintended damage to the equipment.

Watts - Wire Wound Fusible Resistors - High Surge Immunity - Series WWFHS

B0nz3r

1) The document describes wire wound fusible resistors that function as regular resistors under normal conditions but fuse under excessive loads, providing overcurrent protection. 2) These resistors have enhanced surge voltage immunity and are available in various wattage ratings and resistance values. 3) Key specifications include temperature coefficient, short time overload rating, dielectric withstand voltage, fusing characteristics, and electrical performance standards.

Aml catalogue 13

slideroma

The document provides product information for various vacuum measurement and control products from Arun Microelectronics Limited, including: 1) The TSP2 titanium sublimation pump power supply that controls titanium sublimation pumps with up to 4 filaments. 2) The NGC2D dual ion gauge controller that offers integrated pressure measurement and process control for two ion gauges and other gauges. 3) The AIG1xG series of Bayard-Alpert ionization gauges with various filament options. 4) The PVU3 and PVB3 Pirani gaugeheads that can be used with AML ion gauge controllers to measure pressure from 200 mbar to 1x10-

Uniohm resistors datasheet high quality anti-sulfurized thick film chip resis...

Felix Law

This Uniohm resistors datasheet for car 1%-5%, high quality anti-sulfurized thick film chip resistor, nq02~nq12 series. Allchips is the authorized distributor of Uniohm. UNIOHM recommend the storage condition temperature: 15℃~35℃, humidity :25%~75%. (Put condition for individual product). Even under UNIOHM recommended storage condition, solderability of products over 1 year old. (Put condition for each product) may be degraded. Store / transport cartons in the correct direction, which is indicated on a carton as a symbol. Otherwise bent leads may occur due to excessive stress applied when dropping of a carton. Product performance and soldered connections may deteriorate if the products are stored in the following places: a. Storage in high Electrostatic. b. Storage in direct sunshine、rain and snow or condensation.

K32 Controller

Joseph

The document provides installation and wiring instructions for TECNOLOGIC K series controllers. It specifies that the controller is intended for indoor use and should be mounted in an easily accessible location with minimal vibrations that avoids corrosive gases, water or condensation. Wiring guidelines are provided for different input and output types, including thermocouples, RTDs, voltage/current signals, and relays. Configuration and programming procedures are outlined.

5.7 Insulation Test 1

Talia Carbis

An insulation resistance test is conducted to ensure the integrity of insulation between live conductors and earth or between live parts and earth. This helps prevent electric shock, fire hazards from short-circuits, and equipment damage. The test also checks insulation between conductors to minimize potential for breakdown. The insulation is stressed by applying a 500V direct current, though some equipment may require disconnecting or a reduced 250V test voltage. Acceptable insulation resistance values must be at least 1MΩ between conductors and live/earthed parts, though some items like heating elements may register lower and need disconnecting prior to testing.

Similar to Martindale Electric Metrohm MET7A501C Safety Insulation Tester - Martindale Electric Metrohm Flash Testers & Insulation Testers (20)

Datasheet Metrel MI 3250. Hubungi PT. Siwali Swantika 021-45850618

Martindale Electric Metrohm METE3511 5kV Analogue Insulation Tester - Martind...

2 u 650w single power supply

Data Teknis Gossen Metrawatt Ohmmeter : METRAOHM 413

Data Teknis Gossen Metrawatt Insulation Tester METRISO PRO

Uniohm resistors datasheet for car -anti-sulfurized thick film chip resistors...

Imegger, mit 4002, cat iv insulation tester 1000 v, op 54

Data Teknis Gossen Metrawatt Battery Tester : METRACELL - BT PRO

350kV 8000KVA series resonant cable test system

Data Teknis Gossen Metrawatt Insulation Tester METRISO 1000A

METRISO 1000A Insulation Tester

Data Teknis Gossen Metrawatt Multimeter : METRAport 3A

Delta drp024 power_supply_catalog

SEBA KMT MFM5 1 Cable Sheath Testing, Fault Prelocation & Pinpointing

60 Monocrystalline Cell Modules and 72 Mono Crystalline Cell Modules:

Watts - Wire Wound Fusible Resistors - High Surge Immunity - Series WWFHS

Aml catalogue 13

Uniohm resistors datasheet high quality anti-sulfurized thick film chip resis...

K32 Controller

5.7 Insulation Test 1

More from Thorne & Derrick International

Isolation procedures for safe working on electrical systems and equipment by ...

Thorne & Derrick International

Isolation Procedures for Safe Working on Electrical Systems and Equipment by the JIB | solation Procedures for Safe Working on Electrical Systems and Equipment This chart shows the safe isolation procedure that you should use when working on electrical systems and equipment. You'll receive a printed copy of this from your Training Provider, but it's also here as a handy reference to keep electronically. THE RULES OF SAFE ISOLATION ARE: Obtain permission to start work (a Permit may be required in some situations) Identify the source(s) of supply using an approved voltage indicator or test lamp Prove that the approved voltage indicator or test lamp is functioning correctly Isolate the supply(s) Secure the isolation Prove the system/equipment is DEAD using an approved voltage indicator or test lamp Prove that the approved voltage indicator or test lamp is functioning correctly Put up warning signs to tell other people that the electrical installation has been isolated Once the system/equipment is proved DEAD, work can begin Uploaded by THORNE & DERRICK LV HV Jointing, Earthing, Substation & Electrical Eqpt | Explosive Atmosphere Experts & ATEX IECEx.

THORNE & DERRICK LV MV HV Jointing, Earthing, Substation & Electrical Eqpt

Thorne & Derrick International

The Children North East Annual Golf Day Wednesday 9th May 2018

Thorne & Derrick International

The document advertises the Children North East Annual Golf Day fundraising event to be held on May 9th, 2018 at Close House golf course in Northumberland. The event will include a shotgun start at 2pm for teams of four playing in a Stableford scoring competition. The £490 entry fee per team includes breakfast, a two course meal after play, and goodie bags. Proceeds will benefit Children North East, a charity supporting children in the Newcastle region.

3M Electrical Products Stocked By Thorne & Derrick International

Thorne & Derrick International

This document provides information on 3M's electrical products, including electrical connectors, wire connectors, splice kits, wire markers, and protective coatings. It highlights key features and applications of 3M's Scotchlok electrical insulation displacement connectors, Performance Plus wire connectors, direct bury splice kits, ScotchCode wire markers, insulating and anti-corrosion sprays, and Scotchkote electrical coating. The document is intended to showcase 3M's quality solutions for electrical connections, identification, and corrosion protection.

CATU Electrical Safety Catalogue

Thorne & Derrick International

This document provides a catalogue of products from SICAME GROUP for electrical safety. It begins by emphasizing the importance of electrical safety for professionals working in the electrical industry. The catalogue then outlines the company's commitment to supporting customers through new products designed by their teams, an updated catalogue focusing on product functions and uses, and new educational tools like guidance documents. The bulk of the document consists of the catalogue content organized into sections covering personal protective equipment, locking, signaling, low voltage test and measurement, low voltage earthing systems, low voltage live working tools, medium voltage substation equipment, medium voltage equipment, high voltage lines and switchgear equipment, and earthing connections. Each section lists and provides brief descriptions of the various safety products

11kV Cable Termination Heat Shrink Kits 3 Core 16-25sqmm SPS 3TIS-12X-A

Thorne & Derrick International

1) The document provides installation instructions for heatshrink termination of 3 core polymeric cables with voltages ranging from 7.2kV to 36kV. It describes the steps for preparing the cable, installing stress control tapes and tubes, cable lugs, and rain sheds. 2) Key steps include removing the cable sheath and screens, applying stress control tape, installing cable lugs and boots, and shrinking tubes onto the assembly. Proper distances must be maintained for phase clearance and bending radii. 3) Outdoor terminations require additional rain sheds installed from the bottom up at specified distances between the anti-track tube and shed edges. Indoor distances between phases and grounds are also outlined.

THORNE + DERRICK : LV, MV & HV Cable Installation, Jointing, Substation & Ele...

Thorne & Derrick International

THORNE & DERRICK based in the UK are international distributors of LV, MV & HV Cable Installation, Jointing, Substation & Electrical Equipment. Since 1985, T&D have established an international reputation based on SERVICE | INTEGRITY | TRUST. Contact us for 3M, ABB, Alroc, AN Wallis, CATU, Cembre, Centriforce, CMP, CSD, Elastimold, Ellis Patents, Emtelle, Euromold, Filoform , Furse, Lucy Electric & Zodion, Nexans, Pfisterer, Polypipe, Prysmian, Roxtec, Sicame, WT Henley.

Ex d Enclosures - Explosion Proof Hazardous Area Technor EJB Galvanised Steel...

Thorne & Derrick International

The document provides technical specifications for EJB series explosion proof enclosures made of galvanized carbon steel. The enclosures have an IP rating of IP65, IP66, or IP67 and an operating temperature range of -50°C to +60°C. They offer explosion protection of Ex d IIB or IIB+H2 and are suitable for indoor and outdoor use in hazardous industrial areas. The enclosures can house various electrical and electronic components and accessories.

Roxtec Cable Transit - B Frame Dimensional Drawing

Thorne & Derrick International

Pepperl & Fuchs SIL Training Certificate - T&D Adam Rowe

Thorne & Derrick International

T&D Experts In Equipment For Explosive Atmospheres

Thorne & Derrick International

Thorne & Derrick were established in 1985 and are now one of the largest specialist distributors and worldwide exporters of equipment for explosive atmospheres. They stock over 100,000 products from over 100 brands for industries such as oil & gas, mining, manufacturing, and more. Thorne & Derrick provide hazardous area lighting, heating, sensors, detectors, valves, cables, and other equipment certified for explosive atmospheres. They also offer technical support, international delivery, and over 30 years of experience in serving hazardous area applications.

Ultrasonic Flow Meters - Customer Specification Demand

Thorne & Derrick International

This document is an application datasheet for flow measurement devices. It requests contact and process information from customers. It asks for details about the application environment and pipe parameters. It also requests information on process parameters like temperature, pressure, and flow rates. Finally, it inquires about desired measurement configuration including units of measurement, data logging, power supply, and electrical and communication interfaces.

Emtelle Fibre Optic Cables - Product Catalogue 2016

Thorne & Derrick International

This document provides information on Emtelle fibre optic cables, including: - An overview of Emtelle as a leading global manufacturer of blown fibre and ducted network solutions. - Descriptions of different cable types including Direct Install, Direct Buried, Aerial, and more. - Specifications for various cable models including fibre count options, dimensions, tensile strength and other test standards.

Thorne & Derrick Process Heating Brochure 2016

Thorne & Derrick International

Thorne & Derrick provide electrical heating solutions for industrial and hazardous area applications. They have over 30 years of experience in process heating and specialize in frost protection and winterization packages. They offer a wide range of electrical heating equipment for hazardous areas, including portable air heaters certified for use in explosive atmospheres. Their product range and engineering expertise help customers solve heating challenges across various industries.

SIRAI ASCO Numatics Solenoid Valves WRAS Approved - SIRAI L182D L282D

Thorne & Derrick International

Ripley Utility Tool Cable Preparation Tools

Thorne & Derrick International

The document provides information on tools for preparing electric utility distribution and transmission cables. It includes tools for stripping insulation from secondary distribution cables, mid-span stripping of overhead primary distribution cables, insulation stripping and jacket stripping for underground cables, removing insulation shields from underground and transmission cables, pencilling transmission cables, and other specialty distribution tools. Tables provide part numbers and specifications for various cable end strippers and other tools to prepare different cable types.

RIDGID micro CD100 Combustible Gas Detector

Thorne & Derrick International

The document describes the RIDGID micro CD-100 combustible gas leak detector. It can quickly identify the presence of combustible gases with a flexible 41 cm probe. It is designed to detect gases like methane, propane, and more. The micro CD-100 has adjustable sensitivity settings and Tri-Mode Detection that provides alerts through visual, audible or vibration signals. It is listed as catalog number 36163 and weighs 0.45 kg.

Itron Fact Sheet

Thorne & Derrick International

Itron is a leading technology company dedicated to measuring, managing, and analyzing energy and water resources. It provides comprehensive solutions including meters, communication systems, software, and consulting services to over 8,000 customers in more than 100 countries. Itron employs thousands of people globally and invests over 8.5% of its $1.9 billion annual revenue in research and development.

United Nations Environment Programme (UNEP) ‘2006 Report of the Refrigeration...

Thorne & Derrick International

Filoform FiloSeal+HD Reenterable LV HV Power Cable Duct Seal System - Spec Sheet

Thorne & Derrick International

The FiloSeal+HD is a duct sealing system that uses hexagonal tubes and a flexible silicon-based sealant to seal cable configurations and pipes within conduits. It provides resistance to up to 2 bars of pressure and can withstand pulling forces of 100kg on sealed cables. The sealant is easily applied and cures with air, providing high levels of gas and water tightness. The system allows for easy addition or removal of cables or pipes as needed.

More from Thorne & Derrick International (20)

Isolation procedures for safe working on electrical systems and equipment by ...

THORNE & DERRICK LV MV HV Jointing, Earthing, Substation & Electrical Eqpt

The Children North East Annual Golf Day Wednesday 9th May 2018

3M Electrical Products Stocked By Thorne & Derrick International

CATU Electrical Safety Catalogue

11kV Cable Termination Heat Shrink Kits 3 Core 16-25sqmm SPS 3TIS-12X-A

THORNE + DERRICK : LV, MV & HV Cable Installation, Jointing, Substation & Ele...

Ex d Enclosures - Explosion Proof Hazardous Area Technor EJB Galvanised Steel...

Roxtec Cable Transit - B Frame Dimensional Drawing

Pepperl & Fuchs SIL Training Certificate - T&D Adam Rowe

T&D Experts In Equipment For Explosive Atmospheres

Ultrasonic Flow Meters - Customer Specification Demand

Emtelle Fibre Optic Cables - Product Catalogue 2016

Thorne & Derrick Process Heating Brochure 2016

SIRAI ASCO Numatics Solenoid Valves WRAS Approved - SIRAI L182D L282D

Ripley Utility Tool Cable Preparation Tools

RIDGID micro CD100 Combustible Gas Detector

Itron Fact Sheet

United Nations Environment Programme (UNEP) ‘2006 Report of the Refrigeration...

Filoform FiloSeal+HD Reenterable LV HV Power Cable Duct Seal System - Spec Sheet

Martindale Electric Metrohm MET7A501C Safety Insulation Tester - Martindale Electric Metrohm Flash Testers & Insulation Testers

1. 7A501C safety insulation tester The 7A501 has been approved to BS1259 (1958) and carries the Ministry of Power Certificate Number IS1428 (Class 1)and the Factory Inspectorate Certificate Number 2148 (Class 2A and 2C) which covers Methane, Ammonia and Hydrocarbons. The testers have an analogue display and 500V DC insulation test voltage with a short circuit current of less SPECIFICATIONS ELECTRICAL INSULATION MΩ Range: 0 - 50M. Test Voltage: 500V DC±10% across 1MΩ Short Circuit Current: <2mA Accuracy: ±1.6mm of scale arc length than 2mA. On continuity the test voltage is nominally 200mV with a short circuit current of 26mA maximum. A special allen key is required to access the batteries so that they may not be changed in a hazardous area. This tester does not comply with The ATEX94 directive. NOTE: BS1259 is now obsolescent and has been superseded by BS5501. Under BS1259 the tester by itself was approved whereas under BS5501 approvals also consider applications of the tester. CONTINUITY Ω Range: 0 - 50. Test Voltage: Nominal 200mV Short Circuit Current: <26mA Accuracy: ±1.6mm of scale arc length Battery: 6 off 1.5V AA IEC R6B MECHANICAL Size: 132 X 82 X 60mm Material: ABS Weight: 0.6kg Movement: Nominal 1.5mA sensitivity - taut band Scale Length: 70mm Test Leads: 1m long with crocodile clips ENVIRONMENTAL Operating Temperature: 0 to 40°C Storage Temperature: -20°C to 60°C Due to policy of continuous development, Martindale Electric reserves the right to alter equipment specification and description outlined in this document without prior notice. No part of this document shall be deemed to be part of any contract for the equipment unless specifically referred to as an inclusion within such contract. © Martindale Electric Co. Ltd. 2005 Martindale Electric Company Ltd. Metrohm House, Penfold Trading Estate, Imperial Way, Watford, Tel: +44 (0)191 490 1547 01923 441717 Fax: 01923 446900 WD24 4YY. Tel: Fax: +44 (0)191 477 5371 Email: northernsales@thorneandderrick.co.uk E-mail: sales@martindale-electric.co.uk Web site: http://www.martindale-electric.co.uk rev2 Website: www.cablejoints.co.uk www.thorneanderrick.co.uk

Martindale Electric Metrohm MET7A501C Safety Insulation Tester - Martindale Electric Metrohm Flash Testers & Insulation Testers

Recommended

Recommended

More Related Content

What's hot

What's hot (19)

Viewers also liked

Viewers also liked (10)

Similar to Martindale Electric Metrohm MET7A501C Safety Insulation Tester - Martindale Electric Metrohm Flash Testers & Insulation Testers

Similar to Martindale Electric Metrohm MET7A501C Safety Insulation Tester - Martindale Electric Metrohm Flash Testers & Insulation Testers (20)

More from Thorne & Derrick International

More from Thorne & Derrick International (20)

Martindale Electric Metrohm MET7A501C Safety Insulation Tester - Martindale Electric Metrohm Flash Testers & Insulation Testers