Transmission system of ICE Vehicles and Electric VehiclesAvishek Das Gupta
This presentation is about the operating principle of the transmission system in ICE vehicles and electric vehicles. Here I discussed the comparison of ICE vehicles and electric vehicles from the point of view of torque. In this presentation, the basic principle of manual transmission system is described. In automatic transmission system, the objective and working principle of the planetary gear set and the torque converter are described. The schematic diagram of the single-speed transmission system is shown. Difference between the single-speed transmission system and the two-speed transmission system is also shown from the point of view of torque.
The document discusses the components and workings of an engine cooling system in cars. It describes 11 key components: the water jacket, water pump, engine fan, variable speed fan, flexible blade fan, electric fan, radiator, expansion tank, thermostat, cooling bypass passage, and radiator cap. It explains that the cooling system works to remove excess heat from the engine and keep it at optimal temperature for performance and efficiency. The various components work together to circulate coolant and transfer heat from the engine to the radiator to be dissipated.
The document provides an overview of Mahindra First Choice Services, which is part of Mahindra & Mahindra's aftermarket sector. It discusses the foundation and business units of Mahindra, as well as details about Mahindra First Choice Services workshops. The workshop operates in cycles, providing services such as engine repair, brake repair, steering/suspension work, air conditioning, wheel balancing, denting/painting, and car grooming. It describes the process a vehicle goes through from entry to exit and highlights the various engine and vehicle services performed.
The document provides a history of the automobile starting with early steam-powered vehicles in the 1600s and crediting Karl Benz with inventing the modern automobile in 1885. It discusses Henry Ford's introduction of the Model T and assembly line production, which revolutionized transportation. The document also covers fuel and propulsion technologies including gasoline, diesel, electric, hybrid, and alternative fuels. It concludes with benefits of automobiles and their major environmental impacts.
The document summarizes the key components and working of a vacuum brake system used in trains. It describes the driver's brake valve, exhauster, dummy couplings, brake cylinders, vacuum reservoirs, brake pipes and other parts. It explains how applying the brakes causes a loss of vacuum in the brake pipe, pushing the piston up and engaging the brake blocks, while releasing the brakes restores vacuum. The vacuum brake allows partial braking and is fail-safe but is less effective than modern air brakes.
This seminar presentation discusses airless tires as an alternative to traditional pneumatic tires. It provides background on tire function and properties before explaining the key features of airless tires, such as spokes that flex to provide cushioning instead of air pressure. The presentation highlights advantages of airless tires like reduced weight and improved safety. It also notes future challenges like developing materials that can withstand various road conditions and developing airless tire designs optimized for use in space and on other planets.
“Tweel” is nothing but a air less (or) Non pneaumatic tyres
Airless tyres or Non-pneumatic tyres (NPT) , are tyres that are not supported by air pressure.
The document discusses various components and types of vehicle suspension systems. It describes solid axle, double wishbone, and MacPherson strut suspensions. For each type it provides the advantages and disadvantages. It explains key suspension terminology like camber, caster, roll center, and discusses how suspension serves to isolate passengers from road vibrations while improving vehicle control and mobility.
Transmission system of ICE Vehicles and Electric VehiclesAvishek Das Gupta
This presentation is about the operating principle of the transmission system in ICE vehicles and electric vehicles. Here I discussed the comparison of ICE vehicles and electric vehicles from the point of view of torque. In this presentation, the basic principle of manual transmission system is described. In automatic transmission system, the objective and working principle of the planetary gear set and the torque converter are described. The schematic diagram of the single-speed transmission system is shown. Difference between the single-speed transmission system and the two-speed transmission system is also shown from the point of view of torque.
The document discusses the components and workings of an engine cooling system in cars. It describes 11 key components: the water jacket, water pump, engine fan, variable speed fan, flexible blade fan, electric fan, radiator, expansion tank, thermostat, cooling bypass passage, and radiator cap. It explains that the cooling system works to remove excess heat from the engine and keep it at optimal temperature for performance and efficiency. The various components work together to circulate coolant and transfer heat from the engine to the radiator to be dissipated.
The document provides an overview of Mahindra First Choice Services, which is part of Mahindra & Mahindra's aftermarket sector. It discusses the foundation and business units of Mahindra, as well as details about Mahindra First Choice Services workshops. The workshop operates in cycles, providing services such as engine repair, brake repair, steering/suspension work, air conditioning, wheel balancing, denting/painting, and car grooming. It describes the process a vehicle goes through from entry to exit and highlights the various engine and vehicle services performed.
The document provides a history of the automobile starting with early steam-powered vehicles in the 1600s and crediting Karl Benz with inventing the modern automobile in 1885. It discusses Henry Ford's introduction of the Model T and assembly line production, which revolutionized transportation. The document also covers fuel and propulsion technologies including gasoline, diesel, electric, hybrid, and alternative fuels. It concludes with benefits of automobiles and their major environmental impacts.
The document summarizes the key components and working of a vacuum brake system used in trains. It describes the driver's brake valve, exhauster, dummy couplings, brake cylinders, vacuum reservoirs, brake pipes and other parts. It explains how applying the brakes causes a loss of vacuum in the brake pipe, pushing the piston up and engaging the brake blocks, while releasing the brakes restores vacuum. The vacuum brake allows partial braking and is fail-safe but is less effective than modern air brakes.
This seminar presentation discusses airless tires as an alternative to traditional pneumatic tires. It provides background on tire function and properties before explaining the key features of airless tires, such as spokes that flex to provide cushioning instead of air pressure. The presentation highlights advantages of airless tires like reduced weight and improved safety. It also notes future challenges like developing materials that can withstand various road conditions and developing airless tire designs optimized for use in space and on other planets.
“Tweel” is nothing but a air less (or) Non pneaumatic tyres
Airless tyres or Non-pneumatic tyres (NPT) , are tyres that are not supported by air pressure.
The document discusses various components and types of vehicle suspension systems. It describes solid axle, double wishbone, and MacPherson strut suspensions. For each type it provides the advantages and disadvantages. It explains key suspension terminology like camber, caster, roll center, and discusses how suspension serves to isolate passengers from road vibrations while improving vehicle control and mobility.
An axle is a central shaft that supports rotating wheels. On vehicles, the axle can be fixed to the wheels and rotate with them, or fixed to the vehicle with the wheels rotating around it. Bearings are provided where the axle is mounted. The document discusses different types of rear axles like full floating, semi floating, and three quarter floating axles. It also discusses front axles, describing them as either dead or live axles. Finally, it lists four types of stub axles used to connect front wheels to front axles: Elliot, reversed Elliot, Lamoine, and reversed Lamoine.
Frame and Body of Automobile
Introduction to chassis, Classification of chassis, Conventional chassis,
Semi forward chassis, Full forward chassis, Engine at the front, Engine at the rear, Engine in mid, Frame of the automobile, Function of Frame, types of frame, conventional frame, semi-integral frame, integral frame, defects in chassis, Body of the automobile, types of the body in automobile,
The document discusses the brake system used in vehicles. It defines a brake as a device that inhibits motion using friction to convert kinetic energy into heat. Brakes slow or stop a vehicle using friction between stationary and moving parts, with some regenerative brakes converting energy to electricity. The document classifies brakes based on actuation method (foot, hand), operation type (mechanical, hydraulic, air, vacuum), location (front, rear wheels), and application method (internally expanding, externally contracting). Hydraulic brakes are most common, using pressurized brake fluid and Pascal's law to generate equal braking force on all wheels.
Mercedes benz service centre training reportPanchal Anand
Industrial training (Internship) Report.
Mercedes_benz Service centre.
Abstract: As a Mechanical Engineering Student I am very interested in automobile Engineering. I always keen to learn different mechanisms used in vehicles, I used to watch animated videos on YouTube about automobile mechanisms like Differential, Automatic transmission gearbox etc, but I never watched it in real. So, it was a great opportunity for me to do two weeks internship at Mercedes-benz Service centre, Ambli, Ahmedabad. The internship was concentrated on the car services. At the beginning of the internship I had several queries in my mind regarding the different technologies used in Mercedes-benz and what skills are needed in organization. During my internship several queries are cleared by doing some activities. The objective of this internship is to understand working of different mechanisms, to get knowledge of regular services and the major-minor problem that can be observed in day to day life. Apart from technical knowledge, I also learnt rules and safety instruction, Inventory management, Quality Control. I realize the responsibility of technicians working on the car. So, this internship was a great experience. I found out how much I am strong in automobile field. I gained new knowledge and skills and met many new people. Working together with people having different background and education was great experience. I also accompanied by other 2-3 students who were also on industrial training, so it was nice knowledge sharing. I achieved many of my learning goals. I got insight into the work of an organization. At last this internship has given me new insights and motivation to pursue a career in mechanical engineering.
The document discusses the vacuum braking system. It begins with an introduction that defines brakes and describes how vacuum braking systems use engine vacuum to assist hydraulic brakes. It then provides a brief history, stating that vacuum brakes were invented in 1877 and were first used on railway locomotives. The principle section explains that a vacuum in the brake pipe releases the brakes, while a loss of vacuum applies them. It describes the main parts of the system, including the exhauster, brake blocks, vacuum reservoir, and brake pipe. The document concludes with advantages like safety and reliability, and limitations such as slow brake release.
The document discusses the steering system of vehicles. It describes the steering system as the interface between the driver and vehicle that allows the driver to guide the vehicle by controlling the path. It converts rotational motion of the steering wheel into angular turns of the wheels. Factors like steering ratio, geometry, power steering determine the steering effort required and turning radius. Proper alignment of components like caster, camber, toe is important for steering stability and reducing tire wear.
The air brake system uses compressed air to apply pressure to brake pads to stop large heavy vehicles. It has several main components including a brake valve to control air flow, governors to regulate air pressure, air tanks to store compressed air, air compressors to fill the tanks, brake chambers that use air pressure to engage the brakes, and slack adjusters to ensure proper brake clearance.
This document discusses measuring the quality of car maintenance procedures and whether customers should follow manufacturer-recommended service schedules. It outlines common service procedures like checking and changing fluids and filters, inspecting components, and cleaning the vehicle. It also reviews literature on using the SERVQUAL model to measure service quality gaps and research showing engine reliability benefits from periodic oil changes. The conclusion is that following service schedules achieves high customer satisfaction, though continuous improvement is needed in maintenance processes.
The document discusses various components and types of steering gears used in automobiles. It describes common steering mechanisms like rack and pinion gears that convert rotational motion of the steering wheel into linear motion to turn the wheels. Power steering systems are also summarized, including hydraulic and electric power steering that apply pressure or torque to assist the driver in turning the wheels.
Complete guide to Internal Combustion engines (IC engines)Syed Yaseen
The following presentation is a part of an online course called "A brief overview of IC engine". The presentation contains complete information about IC engines and will be helpful for students of Mechanical and Automobile engineering. The presentation is full of graphics to reduce the efforts of students for imagination and help them to understand the concept as soon as possible.
The steering system uses various components like the steering wheel, steering column, steering gear, linkages, and knuckles to transfer rotational motion from the steering wheel to the front wheels. Modern systems commonly use rack and pinion gears. Power steering systems, either hydraulic or electric, apply assistance through pressurized fluid or an electric motor to reduce the effort needed to turn the wheels. Proper design of the steering mechanism ensures easy handling and return of the wheels to straight ahead position.
The aim is to design and to develop an air brake system based on exhaust gas is called “fabrication of air brake system using engine exhaust gas”. The main aim of this project is to reduce the workloads of the engine drive to operate the air compressor, because here the compressor is not operated by the engine drive.
Here we are placing a turbine in the path of exhaust from the engine. The turbine e is connected to a dynamo by means of coupling, which is used to generate power. Depending upon the airflow the turbine will start rotating, and then the dynamo will also starts to rotate. A dynamo is a device which is used to convert the kinetic energy into electrical energy. The generated power can be stored in the battery and then this electric power has loaded to the D.C compressor. The air compressor compresses the atmospheric air and it stored in the air tank and the air tank has pressure relief valve to control the pressure in the tank . The air tank supplies the compressed pneumatic power to the pneumatic actuator through solenoid valve to apply brake. The pneumatic actuator is a double acting cylinder which converts hydraulic energy into linear moti on.
Electronic stability control (ESC) uses sensors to detect loss of control and applies brakes to individual wheels to help drivers maintain control and bring the vehicle back on the intended path. ESC was first introduced by BMW in 1980 and later adopted by other manufacturers. It uses wheel speed, vehicle speed, steering wheel angle, and yaw rate sensors along with brake force controllers and a master cylinder to stabilize the vehicle. Studies show ESC can prevent about one-third of fatal accidents.
Khushin Lakshkar completed a summer internship at Khandelwal Motor Agencies in Mathura, where he studied wheels and tyres. His report discusses the differences and functions of wheels and tyres, describing tyre construction methods like tube and tubeless tyres. It also covers tyre properties, classifications including radial and bias ply construction, and maintenance like rotation and inspection. Wheel requirements and types including pressed steel, spoked, and light alloy wheels are also summarized.
Google announced its first fully functional driverless car ready for testing on public roads, marking a breakthrough in automotive technology. Automakers are also developing automated manual transmissions, vehicle-to-vehicle communication technologies, and advanced driver assistance systems using sensors and automatic braking to increase safety and prevent collisions. Meanwhile, new infotainment systems are allowing smartphone-like interfaces in vehicles, and materials like aluminum are making cars lighter and more fuel efficient.
This document provides publishing information for the 7th edition of the textbook "Modern Automotive Technology" by James E. Duffy. It includes the publisher, author, copyright details, catalog numbers, safety notices, and descriptions of the type styles and components used in the textbook. The textbook covers all eight areas of ASE certification and is designed to help readers learn automotive systems and prepare for careers as technicians. It uses a building block approach and covers traditional and emerging automotive technologies.
Disassemble and reassemble a single cylinder or multi cylinderSunil Kumar
The document describes the process of disassembling and reassembling a four-stroke engine. It begins with an overview of the four stages of the four-stroke engine cycle: intake, compression, power, and exhaust. It then lists the objectives and provides details on the major components of a petrol engine, including the cylinder head, cylinder block, crankcase, flywheel, distributor assembly, ignition coil, and carburetor. Performance criteria for disassembling and reassembling the engine safely and without damage to parts are also outlined.
The document discusses the benefits of using genuine Mercedes-Benz parts for vehicle repairs. It notes that Mercedes-Benz parts undergo rigorous testing to ensure they are tailored to each specific vehicle model. This helps optimize factors like brake performance, windshield wiper pressure and curve, and air filter sealing. Mercedes-Benz parts are also built for quick and easy installation. Using anything other than genuine parts can compromise quality and safety. The document aims to explain why independent service providers should source parts from Mercedes-Benz dealers rather than third parties.
Content Marketing Cage Match: The Battle of the V8 Super Car BrandsKing Content
Welcome to the third in our series of content marketing cage matches!
This time we explore V8 Super Car brands and the way they are utilising content marketing to win the hearts and minds of motoring enthusiasts.
An axle is a central shaft that supports rotating wheels. On vehicles, the axle can be fixed to the wheels and rotate with them, or fixed to the vehicle with the wheels rotating around it. Bearings are provided where the axle is mounted. The document discusses different types of rear axles like full floating, semi floating, and three quarter floating axles. It also discusses front axles, describing them as either dead or live axles. Finally, it lists four types of stub axles used to connect front wheels to front axles: Elliot, reversed Elliot, Lamoine, and reversed Lamoine.
Frame and Body of Automobile
Introduction to chassis, Classification of chassis, Conventional chassis,
Semi forward chassis, Full forward chassis, Engine at the front, Engine at the rear, Engine in mid, Frame of the automobile, Function of Frame, types of frame, conventional frame, semi-integral frame, integral frame, defects in chassis, Body of the automobile, types of the body in automobile,
The document discusses the brake system used in vehicles. It defines a brake as a device that inhibits motion using friction to convert kinetic energy into heat. Brakes slow or stop a vehicle using friction between stationary and moving parts, with some regenerative brakes converting energy to electricity. The document classifies brakes based on actuation method (foot, hand), operation type (mechanical, hydraulic, air, vacuum), location (front, rear wheels), and application method (internally expanding, externally contracting). Hydraulic brakes are most common, using pressurized brake fluid and Pascal's law to generate equal braking force on all wheels.
Mercedes benz service centre training reportPanchal Anand
Industrial training (Internship) Report.
Mercedes_benz Service centre.
Abstract: As a Mechanical Engineering Student I am very interested in automobile Engineering. I always keen to learn different mechanisms used in vehicles, I used to watch animated videos on YouTube about automobile mechanisms like Differential, Automatic transmission gearbox etc, but I never watched it in real. So, it was a great opportunity for me to do two weeks internship at Mercedes-benz Service centre, Ambli, Ahmedabad. The internship was concentrated on the car services. At the beginning of the internship I had several queries in my mind regarding the different technologies used in Mercedes-benz and what skills are needed in organization. During my internship several queries are cleared by doing some activities. The objective of this internship is to understand working of different mechanisms, to get knowledge of regular services and the major-minor problem that can be observed in day to day life. Apart from technical knowledge, I also learnt rules and safety instruction, Inventory management, Quality Control. I realize the responsibility of technicians working on the car. So, this internship was a great experience. I found out how much I am strong in automobile field. I gained new knowledge and skills and met many new people. Working together with people having different background and education was great experience. I also accompanied by other 2-3 students who were also on industrial training, so it was nice knowledge sharing. I achieved many of my learning goals. I got insight into the work of an organization. At last this internship has given me new insights and motivation to pursue a career in mechanical engineering.
The document discusses the vacuum braking system. It begins with an introduction that defines brakes and describes how vacuum braking systems use engine vacuum to assist hydraulic brakes. It then provides a brief history, stating that vacuum brakes were invented in 1877 and were first used on railway locomotives. The principle section explains that a vacuum in the brake pipe releases the brakes, while a loss of vacuum applies them. It describes the main parts of the system, including the exhauster, brake blocks, vacuum reservoir, and brake pipe. The document concludes with advantages like safety and reliability, and limitations such as slow brake release.
The document discusses the steering system of vehicles. It describes the steering system as the interface between the driver and vehicle that allows the driver to guide the vehicle by controlling the path. It converts rotational motion of the steering wheel into angular turns of the wheels. Factors like steering ratio, geometry, power steering determine the steering effort required and turning radius. Proper alignment of components like caster, camber, toe is important for steering stability and reducing tire wear.
The air brake system uses compressed air to apply pressure to brake pads to stop large heavy vehicles. It has several main components including a brake valve to control air flow, governors to regulate air pressure, air tanks to store compressed air, air compressors to fill the tanks, brake chambers that use air pressure to engage the brakes, and slack adjusters to ensure proper brake clearance.
This document discusses measuring the quality of car maintenance procedures and whether customers should follow manufacturer-recommended service schedules. It outlines common service procedures like checking and changing fluids and filters, inspecting components, and cleaning the vehicle. It also reviews literature on using the SERVQUAL model to measure service quality gaps and research showing engine reliability benefits from periodic oil changes. The conclusion is that following service schedules achieves high customer satisfaction, though continuous improvement is needed in maintenance processes.
The document discusses various components and types of steering gears used in automobiles. It describes common steering mechanisms like rack and pinion gears that convert rotational motion of the steering wheel into linear motion to turn the wheels. Power steering systems are also summarized, including hydraulic and electric power steering that apply pressure or torque to assist the driver in turning the wheels.
Complete guide to Internal Combustion engines (IC engines)Syed Yaseen
The following presentation is a part of an online course called "A brief overview of IC engine". The presentation contains complete information about IC engines and will be helpful for students of Mechanical and Automobile engineering. The presentation is full of graphics to reduce the efforts of students for imagination and help them to understand the concept as soon as possible.
The steering system uses various components like the steering wheel, steering column, steering gear, linkages, and knuckles to transfer rotational motion from the steering wheel to the front wheels. Modern systems commonly use rack and pinion gears. Power steering systems, either hydraulic or electric, apply assistance through pressurized fluid or an electric motor to reduce the effort needed to turn the wheels. Proper design of the steering mechanism ensures easy handling and return of the wheels to straight ahead position.
The aim is to design and to develop an air brake system based on exhaust gas is called “fabrication of air brake system using engine exhaust gas”. The main aim of this project is to reduce the workloads of the engine drive to operate the air compressor, because here the compressor is not operated by the engine drive.
Here we are placing a turbine in the path of exhaust from the engine. The turbine e is connected to a dynamo by means of coupling, which is used to generate power. Depending upon the airflow the turbine will start rotating, and then the dynamo will also starts to rotate. A dynamo is a device which is used to convert the kinetic energy into electrical energy. The generated power can be stored in the battery and then this electric power has loaded to the D.C compressor. The air compressor compresses the atmospheric air and it stored in the air tank and the air tank has pressure relief valve to control the pressure in the tank . The air tank supplies the compressed pneumatic power to the pneumatic actuator through solenoid valve to apply brake. The pneumatic actuator is a double acting cylinder which converts hydraulic energy into linear moti on.
Electronic stability control (ESC) uses sensors to detect loss of control and applies brakes to individual wheels to help drivers maintain control and bring the vehicle back on the intended path. ESC was first introduced by BMW in 1980 and later adopted by other manufacturers. It uses wheel speed, vehicle speed, steering wheel angle, and yaw rate sensors along with brake force controllers and a master cylinder to stabilize the vehicle. Studies show ESC can prevent about one-third of fatal accidents.
Khushin Lakshkar completed a summer internship at Khandelwal Motor Agencies in Mathura, where he studied wheels and tyres. His report discusses the differences and functions of wheels and tyres, describing tyre construction methods like tube and tubeless tyres. It also covers tyre properties, classifications including radial and bias ply construction, and maintenance like rotation and inspection. Wheel requirements and types including pressed steel, spoked, and light alloy wheels are also summarized.
Google announced its first fully functional driverless car ready for testing on public roads, marking a breakthrough in automotive technology. Automakers are also developing automated manual transmissions, vehicle-to-vehicle communication technologies, and advanced driver assistance systems using sensors and automatic braking to increase safety and prevent collisions. Meanwhile, new infotainment systems are allowing smartphone-like interfaces in vehicles, and materials like aluminum are making cars lighter and more fuel efficient.
This document provides publishing information for the 7th edition of the textbook "Modern Automotive Technology" by James E. Duffy. It includes the publisher, author, copyright details, catalog numbers, safety notices, and descriptions of the type styles and components used in the textbook. The textbook covers all eight areas of ASE certification and is designed to help readers learn automotive systems and prepare for careers as technicians. It uses a building block approach and covers traditional and emerging automotive technologies.
Disassemble and reassemble a single cylinder or multi cylinderSunil Kumar
The document describes the process of disassembling and reassembling a four-stroke engine. It begins with an overview of the four stages of the four-stroke engine cycle: intake, compression, power, and exhaust. It then lists the objectives and provides details on the major components of a petrol engine, including the cylinder head, cylinder block, crankcase, flywheel, distributor assembly, ignition coil, and carburetor. Performance criteria for disassembling and reassembling the engine safely and without damage to parts are also outlined.
The document discusses the benefits of using genuine Mercedes-Benz parts for vehicle repairs. It notes that Mercedes-Benz parts undergo rigorous testing to ensure they are tailored to each specific vehicle model. This helps optimize factors like brake performance, windshield wiper pressure and curve, and air filter sealing. Mercedes-Benz parts are also built for quick and easy installation. Using anything other than genuine parts can compromise quality and safety. The document aims to explain why independent service providers should source parts from Mercedes-Benz dealers rather than third parties.
Content Marketing Cage Match: The Battle of the V8 Super Car BrandsKing Content
Welcome to the third in our series of content marketing cage matches!
This time we explore V8 Super Car brands and the way they are utilising content marketing to win the hearts and minds of motoring enthusiasts.
Mercedes-Benz was formed in 1926 through the merger of Daimler and Benz. It is now owned by Daimler AG. Mercedes-Benz produces luxury vehicles and accessories, and owns part of the Formula One racing team McLaren. It focuses on premium pricing and technology innovation. Mercedes-Benz emphasizes reducing emissions and improving fuel efficiency through hybrid, electric, and alternative fuel vehicles. It also supports social and environmental initiatives in India related to employment, education, and biodiesel development.
1) The document discusses various topics in the automotive industry including new car operation systems without manual driving, the role of technology companies like Nvidia in replacing core drivers, and transforming the driving experience.
2) It also discusses Honda's focus on customer satisfaction and their engineers taking pride in achieving goals.
3) The document covers balancing issues during development, ways to improve engine capacity through changes to intake valves and materials, and the importance of meeting quality requirements and customer expectations through assessment.
The document compares the Porsche Cayenne to the Mercedes-Benz M-Class and Audi Q7. It provides specifications, reviews, and price comparisons for each vehicle. Customer comments were also presented discussing reliability issues with the Mercedes-Benz M-Class, such as frequent repairs needed and engine problems.
Atlas honda internship report by qazi zohaib aqilqazizohaibaqil
This internship report summarizes research conducted at Atlas Honda to understand reasons for a sales decline in the first quarter of 2014. The report includes:
1) Visits to 10 dealerships across Pakistan to gather feedback, finding that new dealerships may be causing demotivation, and changes to motorcycle designs were not well received.
2) A survey of 49 consumers finding that while both Honda and Chinese motorcycles are seen as having good prices, Honda is seen as more durable and better designed.
3) A comparison of Honda and Chinese motorcycles on attributes like price, durability, design, and maintenance, finding that Honda scores higher for durability and design.
This document brings together a set
of latest data points and publicly
available information relevant for
Automotive Industry. We are very
excited to share this content and
believe that readers will benefit from
this periodic publication immensely.
The document provides an analysis of the upcoming Honda Amaze sedan. It will be Honda's first diesel car in India, expected to launch in 2013-2014. It will utilize a 1.5L multijet diesel engine to provide good fuel efficiency between 15-16 km/L. The Amaze is aimed at competing in the entry-level sedan segment against cars like the Maruti Suzuki Dzire. It promises comfortable interiors, reasonable performance figures, and standard safety and audio features. However, its success will depend on factors like India's economic conditions, high interest rates, and stringent emission regulations.
Hyundai is a global automaker founded in 1947 that currently ranks as the fourth largest vehicle manufacturer worldwide. The company operates maintenance, repair, and painting workshops to service its models. During an internship, the presenter learned about the functions of these departments, which work together to identify issues, repair damage, and solve problems for customers. Common vehicle problems addressed include knocking engines, suspension alignment faults, engine and brake seizures, which can result from issues like a lack of lubrication or carbon buildup.
The document discusses how to maintain a BMW car to enhance its lifespan. It recommends routinely tuning up the car to prevent costly repairs down the line. This involves keeping components like spark plugs and sensors in good working condition. It also advises changing filters regularly, such as the oil filter every 3,000 miles, to prevent damage. Additionally, the transmission fluid should be changed every 25,000 miles to avoid shifting problems. Lastly, it's important to use an experienced mechanic for BMW maintenance to properly service it and avoid voiding the warranty.
Mohammed Wajahat Khan completed an industrial training internship at Mercedes Benz Service Centre Benchmark Cars in Bhopal, India from May 10th to June 10th. During the internship, he learned about various vehicle mechanisms and technologies firsthand by assisting with car services and repairs. He gained knowledge from skilled technicians about technical skills, safety procedures, quality management, and job responsibilities. The internship helped clear up Khan's initial queries and confirmed his interest in the automotive field.
“Customer awareness and preferring Skoda Yeti.”jitharadharmesh
The document is a summer training project report that focuses on customer awareness and preferences for the Skoda Yeti vehicle. It includes sections on acknowledging those who provided guidance and support, preface discussing the purpose and scope of the training project, and an executive summary outlining the key tasks performed such as analyzing customer feedback and satisfaction data.
The document outlines the history and operations of Mercedes-Benz, including its origins in 1886 in Germany, establishment in India in 1994, and vision to be pioneering and innovative in sustainable mobility. It discusses Mercedes-Benz's model range, competition from BMW, Audi and others, and use of cloud technology. The summary provides an overview of key details about Mercedes-Benz.
This document contains information about the hours of operation for parts and service departments at Unicars Honda on various days of the week, as well as information about vehicles, services, and promotions offered at Unicars Honda. The hours of operation are listed as Monday through Saturday from 7:00am to 6:00pm and Sunday being closed. Information provided includes details on paint protection services, environmental hazards that can damage vehicles, vehicle models such as the Honda S2000 and Odyssey, financing options, and the location of Unicars Honda.
The all new C-Class leads the segment with a host of best-in-segment features: the most powerful petrol engine, best power to weight ratio, longest wheelbase, fastest in the 0–100 kmph sprint and the lightest body shell.
Mercedes-Benz traces its origins to 1886 and the creation of the first petrol-powered car by Karl Benz. It was formed in 1926 by the merger of Karl Benz's and Gottlieb Daimler's companies. Mercedes-Benz entered the Indian market in 1994 and has manufacturing plants in Pune and Chennai. It targets upper middle and upper class individuals seeking a luxury automobile and status symbol. While it faces strong competition and high costs, Mercedes-Benz maintains strategic advantages as the oldest luxury car manufacturer through innovative technology, quality service, and strong brand equity.
Tvs motors summer internship report a study on customer satisfaction towards ...Priyansh Kesarwani
A study on Customer satisfaction towards TVS Motors in Kanpur City
Objective of the study:
• To know the customer satisfaction level towards services of TVS Motors.
• To know the problems presently faced by the customers at TVS Motors.
• To study the post-sales service performance.
• To know the new area of improvement.
Gordons Ford is a family-run Ford dealership established in 1914 that sells over 2000 vehicles per year. It prides itself on excellent customer service and being recognized as one of the top 3 Ford business centers in the UK. The dealership offers a range of financing options for business customers and can provide customized vehicle conversions through its partnerships with specialists. It aims to be a one-stop shop for customers' business needs.
Thus, the engine of your Audi will require the right amount of fuel from the fuel tank to cruise and accelerate smoothly. To fulfill the fuel demand of the engine, it has a well-functional fuel pump that can deliver the right amount of fuel to the engine for creating the necessary spark and generating the horsepower for efficient driving. When it is failed in your Audi, you will notice the signs defined in the following slide.
This slide is special for master students (MIBS & MIFB) in UUM. Also useful for readers who are interested in the topic of contemporary Islamic banking.
ISO/IEC 27001, ISO/IEC 42001, and GDPR: Best Practices for Implementation and...PECB
Denis is a dynamic and results-driven Chief Information Officer (CIO) with a distinguished career spanning information systems analysis and technical project management. With a proven track record of spearheading the design and delivery of cutting-edge Information Management solutions, he has consistently elevated business operations, streamlined reporting functions, and maximized process efficiency.
Certified as an ISO/IEC 27001: Information Security Management Systems (ISMS) Lead Implementer, Data Protection Officer, and Cyber Risks Analyst, Denis brings a heightened focus on data security, privacy, and cyber resilience to every endeavor.
His expertise extends across a diverse spectrum of reporting, database, and web development applications, underpinned by an exceptional grasp of data storage and virtualization technologies. His proficiency in application testing, database administration, and data cleansing ensures seamless execution of complex projects.
What sets Denis apart is his comprehensive understanding of Business and Systems Analysis technologies, honed through involvement in all phases of the Software Development Lifecycle (SDLC). From meticulous requirements gathering to precise analysis, innovative design, rigorous development, thorough testing, and successful implementation, he has consistently delivered exceptional results.
Throughout his career, he has taken on multifaceted roles, from leading technical project management teams to owning solutions that drive operational excellence. His conscientious and proactive approach is unwavering, whether he is working independently or collaboratively within a team. His ability to connect with colleagues on a personal level underscores his commitment to fostering a harmonious and productive workplace environment.
Date: May 29, 2024
Tags: Information Security, ISO/IEC 27001, ISO/IEC 42001, Artificial Intelligence, GDPR
-------------------------------------------------------------------------------
Find out more about ISO training and certification services
Training: ISO/IEC 27001 Information Security Management System - EN | PECB
ISO/IEC 42001 Artificial Intelligence Management System - EN | PECB
General Data Protection Regulation (GDPR) - Training Courses - EN | PECB
Webinars: https://pecb.com/webinars
Article: https://pecb.com/article
-------------------------------------------------------------------------------
For more information about PECB:
Website: https://pecb.com/
LinkedIn: https://www.linkedin.com/company/pecb/
Facebook: https://www.facebook.com/PECBInternational/
Slideshare: http://www.slideshare.net/PECBCERTIFICATION
How to Manage Your Lost Opportunities in Odoo 17 CRMCeline George
Odoo 17 CRM allows us to track why we lose sales opportunities with "Lost Reasons." This helps analyze our sales process and identify areas for improvement. Here's how to configure lost reasons in Odoo 17 CRM
This presentation was provided by Steph Pollock of The American Psychological Association’s Journals Program, and Damita Snow, of The American Society of Civil Engineers (ASCE), for the initial session of NISO's 2024 Training Series "DEIA in the Scholarly Landscape." Session One: 'Setting Expectations: a DEIA Primer,' was held June 6, 2024.
Exploiting Artificial Intelligence for Empowering Researchers and Faculty, In...Dr. Vinod Kumar Kanvaria
Exploiting Artificial Intelligence for Empowering Researchers and Faculty,
International FDP on Fundamentals of Research in Social Sciences
at Integral University, Lucknow, 06.06.2024
By Dr. Vinod Kumar Kanvaria
हिंदी वर्णमाला पीपीटी, hindi alphabet PPT presentation, hindi varnamala PPT, Hindi Varnamala pdf, हिंदी स्वर, हिंदी व्यंजन, sikhiye hindi varnmala, dr. mulla adam ali, hindi language and literature, hindi alphabet with drawing, hindi alphabet pdf, hindi varnamala for childrens, hindi language, hindi varnamala practice for kids, https://www.drmullaadamali.com
Main Java[All of the Base Concepts}.docxadhitya5119
This is part 1 of my Java Learning Journey. This Contains Custom methods, classes, constructors, packages, multithreading , try- catch block, finally block and more.
How to Add Chatter in the odoo 17 ERP ModuleCeline George
In Odoo, the chatter is like a chat tool that helps you work together on records. You can leave notes and track things, making it easier to talk with your team and partners. Inside chatter, all communication history, activity, and changes will be displayed.
This presentation includes basic of PCOS their pathology and treatment and also Ayurveda correlation of PCOS and Ayurvedic line of treatment mentioned in classics.
2. Autorounders is an
automobile garage that
specializes in brands such
as, Mercedes Benz, BMW,
Audi, Skoda and
Volkswagen. I had the
privilege of working there
as an intern mechanic
and sales representative.
This particular garage is
run by Jatin Patel, a
graduate in automobile
engineering. The next few slides
will cover a few of
my experiences with
different cars at the
garage.
3. A 2008 Nissan Teana came in
with a faulty set of spark plugs
and a long worn front
suspension
4. A coolant pipe that had to be opened to
remove the intake manifold
9. A completely worn out
dog bone mount on a
Skoda Octavia was
replaced since the car
was experiencing severe
vibrations. The mount is
used to hold the engine
in place
10. The new part substantially decreased
the vibrations
11. I was asked to write a blog about how an Mercedes Benz
Ml250d was repaired by Autorounders. A link of same is
mentioned below
https://docs.google.com/document/d/1zhiFxtF3K2QBHdj4
bIH701CxuLhcxNlsYUj8phCf0wY/edit?usp=sharing
12. Old and new parts for the
front suspension of a
Mercedes Benz Ml350d
13.
14. The joints had to be cleaned
well before any refitting was
done
15. The control arm bushes of the car had
taken quite the hit and had to be
replaced
16. The new suspension linkages helped
make the car’s ride quality a lot better
than before
28. I am glad to say that, my experience at Autorounders was fruitful in
a lot more ways than I anticipated. The passion for the automobile
was enhanced to an even greater level, and my knowledge and
understanding of machines increased exponentially. It was simply
an experience I couldn’t have had anywhere else, making it one of
my favourite and most engaging activities. I hope to further
develop my skills and knowledge to an extent that will allow me to
contribute to the field as much as I can.
I have attached a link to a letter written by the senior management
of the company that speaks of their perspective of the Internship.
https://docs.google.com/document/d/1_PgdeeXVFYnCwugYg4g-
xeHMCsoaqiaYZJH4ocEuCT0/edit?usp=sharing
Thank you