This document provides an overview of solutions and solubility. It defines key terms like solute, solvent, solution, homogeneous mixture, heterogeneous mixture, concentration, saturation, and factors that affect solubility. It also discusses quantitative concepts such as molarity, percent by mass, and how to use stoichiometry to solve for different units in solution reactions. The key information is that a solution is a homogeneous mixture of two or more substances, with the solute dissolving in the solvent, and various physical and chemical factors influence how much solute can dissolve.
A chemical reaction describes what occurs in a chemical change. It shows not only the kind but also the relative amounts of the substances involved in a change. The coefficients written before the formulas in a balanced equation represent the number of moles of each substance involved in a reaction. Since the number of moles is related to the mass of any substance and to the volume of any gaseous substance, the mole relationship can be easily changed to mass/volume relationship. The concepts on how to calculate molarity, molality and normality are important in identifying the relative amounts of the substances involved in a chemical reaction.
Solutions: types and properties of solutions. Units of concentration, ideal and real
solutions. Henry’s law, distribution of solids between two immiscible liquids, distribution
law. Partition coefficient and solvent extraction.
A chemical reaction describes what occurs in a chemical change. It shows not only the kind but also the relative amounts of the substances involved in a change. The coefficients written before the formulas in a balanced equation represent the number of moles of each substance involved in a reaction. Since the number of moles is related to the mass of any substance and to the volume of any gaseous substance, the mole relationship can be easily changed to mass/volume relationship. The concepts on how to calculate molarity, molality and normality are important in identifying the relative amounts of the substances involved in a chemical reaction.
Solutions: types and properties of solutions. Units of concentration, ideal and real
solutions. Henry’s law, distribution of solids between two immiscible liquids, distribution
law. Partition coefficient and solvent extraction.
Unit 8 - Information and Communication Technology (Paper I).pdfThiyagu K
This slides describes the basic concepts of ICT, basics of Email, Emerging Technology and Digital Initiatives in Education. This presentations aligns with the UGC Paper I syllabus.
Honest Reviews of Tim Han LMA Course Program.pptxtimhan337
Personal development courses are widely available today, with each one promising life-changing outcomes. Tim Han’s Life Mastery Achievers (LMA) Course has drawn a lot of interest. In addition to offering my frank assessment of Success Insider’s LMA Course, this piece examines the course’s effects via a variety of Tim Han LMA course reviews and Success Insider comments.
A Strategic Approach: GenAI in EducationPeter Windle
Artificial Intelligence (AI) technologies such as Generative AI, Image Generators and Large Language Models have had a dramatic impact on teaching, learning and assessment over the past 18 months. The most immediate threat AI posed was to Academic Integrity with Higher Education Institutes (HEIs) focusing their efforts on combating the use of GenAI in assessment. Guidelines were developed for staff and students, policies put in place too. Innovative educators have forged paths in the use of Generative AI for teaching, learning and assessments leading to pockets of transformation springing up across HEIs, often with little or no top-down guidance, support or direction.
This Gasta posits a strategic approach to integrating AI into HEIs to prepare staff, students and the curriculum for an evolving world and workplace. We will highlight the advantages of working with these technologies beyond the realm of teaching, learning and assessment by considering prompt engineering skills, industry impact, curriculum changes, and the need for staff upskilling. In contrast, not engaging strategically with Generative AI poses risks, including falling behind peers, missed opportunities and failing to ensure our graduates remain employable. The rapid evolution of AI technologies necessitates a proactive and strategic approach if we are to remain relevant.
Palestine last event orientationfvgnh .pptxRaedMohamed3
An EFL lesson about the current events in Palestine. It is intended to be for intermediate students who wish to increase their listening skills through a short lesson in power point.
Francesca Gottschalk - How can education support child empowerment.pptxEduSkills OECD
Francesca Gottschalk from the OECD’s Centre for Educational Research and Innovation presents at the Ask an Expert Webinar: How can education support child empowerment?
The French Revolution, which began in 1789, was a period of radical social and political upheaval in France. It marked the decline of absolute monarchies, the rise of secular and democratic republics, and the eventual rise of Napoleon Bonaparte. This revolutionary period is crucial in understanding the transition from feudalism to modernity in Europe.
For more information, visit-www.vavaclasses.com
How to Make a Field invisible in Odoo 17Celine George
It is possible to hide or invisible some fields in odoo. Commonly using “invisible” attribute in the field definition to invisible the fields. This slide will show how to make a field invisible in odoo 17.
2. Mixtures – a review
• Mixture: a combination of two or more
substances that do not combine
chemically, but remain the same
individual substances; can be separated
by physical means.
• Two types:
– Heterogeneous
– Homogeneous
3. Heterogeneous Mixture
• “Hetero” means “different”
• Consists of visibly different substances or
phases (solid, liquid, gas)
• Can be separated by filtering
• Example:
4. Homogeneous Mixture
• “Homo” means the same
• has the same uniform appearance and
composition throughout; maintain one phase
(solid, liquid, gas)
• Commonly referred to as solutions
• Example:
Salt Water
5. Solution
• Solution: a mixture of two or more substances
that is identical throughout (homogeneous)
• can be physically separated
• composed of solutes and solvents
the substance being dissolved
the substance that dissolves the solute
Iced Tea Mix
(solute)
Water
(solvent)
Iced Tea
(solution)
Salt water is
considered a
solution. How can it
be physically
separated?
6. Solution
• The solvent is the largest part of the solution
and the solute is the smallest part of the
solution
Chemistry-Borders IPC-Solutions-Borders
S O L V E N T
S O L U T E
7. Types of Solutions
Gaseous solutions – air = Oxygen + Nitrogen
Liquid solutions – drinks = mix + water
Solid solutions – alloys = steel, brass, etc
8. Concentration
• the amount of solute dissolved in a
solvent at a given temperature
•described as dilute if it has
a low concentration of solute
dissolved
•described as concentrated
if it has a high concentration
of solute dissolved
9. Concentration
•Unsaturated - has a less than the
maximum concentration of solute
dissolved
•Saturated - has the maximum
concentration of solute dissolved
(can see solid in bottom of
solution)
•Supersaturated -contains more
dissolved solute than normally
possible (usually requires an
increase in temperature followed
by cooling)
10. Solubility
• the amount of solute that
dissolves in a certain amount of a
solvent at a given temperature
and pressure to produce a
saturated solution
11. Factors affecting solubility of solids
Temperaturee
increased temperature causes
solids to dissolve faster
Shaking
Note: Increasing the amount of solute
DOES NOT increase the rate of dissolving
Shaking (agitation) causes
solids to dissolve faster
Smaller particles dissolve
Faster because they have
more surface area
Particle Sizee
12. • Miscible liquids can easily dissolve in one
another.
• Immiscible liquids are not soluble in
each other.
Chemistry-Borders
13. Polarity and Dissolving
• Chemists use the saying
“like dissolves like”:
Polar solutes tend to
dissolve in polar
solvents.
Nonpolar solutes tend to
dissolve in nonpolar
solvents.
Oil is nonpolar while water is
polar. They are immiscible.
15. To read the
graph, find the
line for the
substance. The
amount that
dissolves at a
given
temperature is
on the y- axis.
16. How much KNO3
dissolves in 100g
(or 100mL H2O
at 50oC?
1.Find the line (green)
2.Find the temperature
and follow up to the
line.(red arrow)
3. Read across to the y-
axis and this is the
answer. (blue arrow)
4. Since it is more than
½-way between 80 and
90, it is 87.
17. A point on the line is a saturated solution.
Above the line is supersaturated.
Below the line is unsaturated.
18. Using Solubility Curves
What is the solubility of
NaNO3 in 100 g of H2O at
0°C?
How many grams of KNO3
will dissolve in 200g of
H2O at 45°C?
How much water is needed to
dissolve 190g of NaNO3 at
30°C?
73g NaNO3
75g = ?
100g H2O 200g H2O
= 150 g KNO3
95g = 190g
100g H2O ? g H2O
= 200 g H2O
20. Molarity
• Molarity is the concentration of a
solution expressed in moles of solute
per Liter of solution.
• Molarity is a conversion factor for
calculations
Molarity (M) = moles of solute
Liters of solution
21. Molarity
M = mol (solute)
L (solution)
• Example 1: What is the molarity of a solution
that has 2.3 moles of sodium chloride in 0.45
liters of solution?
2.3 moles NaCl = 5.1M NaCl
0.45 L
22. Molarity
M = mol (solute)
L (solution)
• Example 2: How many moles of Na2CO3 are there
in 10.0 L of 2.0 M solution?
10.0 L 2.0 mol Na2CO3
1 1 L
= 20.0 moles Na2CO3
23. Molarity
M = mol (solute)
L (solution)
• Example 3: How many moles of KNO3 are needed
to make 450. mL of 1.5 molar solution?
450. mL 1L 1.5 mol KNO3
1 1000mL 1L
= .675 moles KNO3
24. Molarity
M = mol (solute)
L (solution)
• Example 4: How many grams of NaCl are needed
to make 3.0 L of 1.5 M solution?
3.0 L 1.5 mol NaCl 58.44 g NaCl
1 1 L 1 mol NaCl
= 260 g NaCl
25. Molarity
M = mol (solute)
L (solution)
• Example 5: How many L of 4.0 M solution can be
made with 132g of NaCl ?
132 g NaCl 1 mol NaCl 1 L
1 58.44 g NaCl 4.0 mol NaCl
= .565 L
27. Dilutions and Molarity
• Use this formula to make a more dilute
solution from a concentrated solution
Molarity1 x Volume1 = Molarity2 x Volume2
(Concentrated) (Dilute)
(before) = (after)
M1V1 = M2V2
28. Example 1
How many liters of 2.5 M HCl are
required to make 1.5 L of 1.0 M HCl?
M1V1 = M2V2
M1 = 2.5 M
V1 = ?
M2 = 1.0 M
V2 = 1.5 L
(2.5M) V1 = (1.0M) (1.5 L)
2.5M
2.5M
= 0.60L
29. Example 1
M1 = 2.5M V1 = 0.60L M2 = 1.0 M V2= 1.5 L
How much water should you add to the volume
of 2.5M HCl you calculated above to make the
solution? (draw this in your notes)
1st add .60L of HCl to
measuring device.
30. Example 1
M1 = 2.5M V1 = 0.60L M2 = 1.0 M V2= 1.5 L
How much water should you add to the volume of 2.5M
HCl you calculated above to make the solution?
Then add enough water to get
to 1.5L of solution
V2 – V1 = Amount of water
1.5L – 0.60L = 0.90L water
31. Example 1
M1 = 2.5M V1 = 0.60L M2 = 1.0 M V2= 1.5 L
How much water should you add to the volume of 2.5M
HCl you calculated above to make the solution?
Final solution is 1.5L
of 1.0M HCl
32. Example 2
• 250.0 mL of a 0.500 M HCl solution needs
to be made from concentrated HCl. What
volume of the concentrated solution is
needed if its molarity is 12.0 M?
M1V1 = M2V2
M1 =
V1 =
M2 =
V2 =
33. Example 2
• 250.0 mL of a 0.500 M HCl solution needs to be made
from concentrated HCl. What volume of the
concentrated solution is needed if its molarity is
12.0 M?
M1V1 = M2V2
M1 = 12.0M
V1 = 10.4mL
M2 = 0.500M
V2 = 250.0mL
How much water would you
add to make the final
solution?
250.0mL - 10.4mL = 239.6mL
35. Mass Percent
• Solutions can also be represented as percent
of solute in a specific mass of solution.
• For a solid dissolved in water, you use percent
by mass which is Mass Percent.
• % by mass = mass solute x 100
mass of solution
**Mass of solution = solute mass + solvent mass
36. Example 1
• If a solution that has a mass of 800.0
grams contains 20.0 grams of NaCl,
what is the concentration using Percent
by Mass?
% by mass = mass solute x 100
mass of solution
% by mass = 20.0g NaCl x 100
800.0g solution
= 2.50% NaCl
37. Example 2
• If 10.0 grams of NaCl is dissolved in
90.0 grams of water, what is the
concentration using Percent by Mass?
% by mass = mass solute x 100
mass of solution
% by mass = 10.0g NaCl x 100 = 10.0%NaCl
100.0g solution
38. Example 3
• How many grams of sodium bromide are
in 200.0g of solution that is 15.0%
sodium bromide by mass?
% by mass = mass solute x 100
mass of solution
% by mass = ? g NaBr x 100 = 15.0%NaBr
200.0g solution
g NaBr = 200.0 x 15.0
100
= 30 g NaBr
40. Solution Stoichiometry
• When we previously did stoichiometry
for a reaction to determine theoretical
yield, we only worked with GRAMS and
MOLES
• Ex/ How many MOLES of HCl are
required to react with 13 GRAMS of
zinc?
Zn + 2 HCl ZnCl2 + H2
41. Solution Stoichiometry
• But we may be given something OTHER than
grams and moles
• We can use stoichiometry to solve for ANY
unit. We just need to make sure units cancel
out and we end up with the unit we are trying
to solve for!
• The mole ratio using coefficients from the
balanced chemical equation is the key to
switching between compounds
42. Solution Stoichiometry
Ex/ How many LITERS of 12 M HCl are
required to react with 13.0 GRAMS of zinc?
Zn + 2 HCl ZnCl2 + H2
13.0g Zn 1 mole Zn 2 mol HCl 1L HCl
1 65.38g Zn 1 mol Zn 12 mol HCl
Remember – Molarity (M) is a conversion Factor
= 0.0331 L HCl
43. Solution Stoichiometry
• Ex/ How many grams of NaOH would be
required to react with 1.50 L of 3.75M
sulfuric acid?
H2SO4 + NaOH Na2SO4 + H2O
1.50L 1 H2SO4 3.75 mole H2SO4 2 mol NaOH 40.00g NaOH
1 1 L H2SO4 1 mole H2SO4 1 mol NaOH
= 450. g NaOH