Preparation of planning documents for instrumentation, power plants and control but also installation and process measuring and control technology are in the competence of the electric design engineer. The common data base permits at any time the access to information about all trades involved in the project such that planning of electrical engineering can be combined with planning of process engineering.
The Module for Project Manager and Repair & Maintenance Staff
CADISON® Project Navigator is the module for viewing of project data within the corporate network. Navigator has been designed for staff members normally not involved in the active planning of a plant but afterwards responsible for operation and maintenance of the plant (i.e. mere data consumers).
Since in a CADISON® project all logic and functional interrelations are displayed, it is possible, e.g. in case a pump fails operation, to make visible all plant components affected by this failure. In case problems occur, all components, safety zones, pipe runs, hazardous areas etc. that might be affected are recognized and/or displayed.
CADISON® Project Engineer is your tool for plant design, Engineering calculations and detailing of your plant by adding all required components (objects) to the project while taking them from the catalogue. Simple Drag & Drop operations are sufficient with completely text based operations without the obligation to have a graphical environment. This approach is called "Conceptual Engineering". The target of CADISON® Project Engineer is to provide the user with data for calculation without large efforts and already at a very early time.
The CADISON® P&ID Designer plays a decisive role in design, construction, commissioning and maintenance and has an enormous effect on the complete lifecycle of a plant. In this case the preliminary project engineering will be integrated with Basic and Detail Engineering and 2D layout planning. Apart from the P&I diagrams the P&ID Designer even creates block flow charts and process flow diagrams (PFD).
The Module for 3D Layout and Piping Planning
Installation and pipeline planning in the 3D model are in the competence of the 3D Designer. Normally this module is used for access to data from Basic Engineering or P&ID. Efficient assistants are available for installation planning: For instance, isometrics can be automatically generated from the planned pipeline systems.
Start with an empty sheet of paper, access an existing 3D Design model - even an AutoCAD model - or access data from Basic Engineering or P&ID! You can simply take your data - either graphic data or data from plant structure – through Drag & Drop and insert them in your 3D design environment for further processing as required.
Preparation of planning documents for instrumentation, power plants and control but also installation and process measuring and control technology are in the competence of the electric design engineer. The common data base permits at any time the access to information about all trades involved in the project such that planning of electrical engineering can be combined with planning of process engineering.
The Module for Project Manager and Repair & Maintenance Staff
CADISON® Project Navigator is the module for viewing of project data within the corporate network. Navigator has been designed for staff members normally not involved in the active planning of a plant but afterwards responsible for operation and maintenance of the plant (i.e. mere data consumers).
Since in a CADISON® project all logic and functional interrelations are displayed, it is possible, e.g. in case a pump fails operation, to make visible all plant components affected by this failure. In case problems occur, all components, safety zones, pipe runs, hazardous areas etc. that might be affected are recognized and/or displayed.
CADISON® Project Engineer is your tool for plant design, Engineering calculations and detailing of your plant by adding all required components (objects) to the project while taking them from the catalogue. Simple Drag & Drop operations are sufficient with completely text based operations without the obligation to have a graphical environment. This approach is called "Conceptual Engineering". The target of CADISON® Project Engineer is to provide the user with data for calculation without large efforts and already at a very early time.
The CADISON® P&ID Designer plays a decisive role in design, construction, commissioning and maintenance and has an enormous effect on the complete lifecycle of a plant. In this case the preliminary project engineering will be integrated with Basic and Detail Engineering and 2D layout planning. Apart from the P&I diagrams the P&ID Designer even creates block flow charts and process flow diagrams (PFD).
The Module for 3D Layout and Piping Planning
Installation and pipeline planning in the 3D model are in the competence of the 3D Designer. Normally this module is used for access to data from Basic Engineering or P&ID. Efficient assistants are available for installation planning: For instance, isometrics can be automatically generated from the planned pipeline systems.
Start with an empty sheet of paper, access an existing 3D Design model - even an AutoCAD model - or access data from Basic Engineering or P&ID! You can simply take your data - either graphic data or data from plant structure – through Drag & Drop and insert them in your 3D design environment for further processing as required.
SAP Data Lookup for HD3D Visual Reporting. Routing ERP information, managed inside SAP, into the NX CAD framework to establish HD3D Visual Reporting as supporting dahsboard tool for enabling faster and smarter decisions. Review of the implementation of HD3D Visual Reporting at GEA Farm Technologies GmbH.
Preparation of planning documents for instrumentation, power plants and control but also installation and process measuring and control technology are in the competence of the electric design engineer. The common data base permits at any time the access to information about all trades involved in the project such that planning of electrical engineering can be combined with planning of process engineering.
CAESAR II é uma solução completa que permite uma análise rápida e precisa dos sistemas de tubulações sujeitos a uma ampla variedade de cargas que levam em consideração as condições de peso, de pressão, térmicas, sísmicas e outras condições estáticas e dinâmicas. Ele pode analisar sistemas de tubulações de virtualmente qualquer dimensão ou complexidade.
Para maiores informações:
www.natecnologia.com.br
Product Structure Analysis - Alternative ToolsMatthias Ahrens
A proposal for using network visualization tools, which are used in bio-analytics, social network analytics and ontology representation, for the visualization tasks of complex product structures. To establish a mass customization approach the modularity and variant structures and dependencies habe to be build up accurately in the product structures, managed in the ERP and PLM frameworks. Sometimes it is required to review and visualize such dependencies across multiple domains. Offline network visualization tools like Cytoscape, Protégé and Gephi can be an option to support this data visualization tasks.
Standardization in Graphics, Graphics KERNEL System, Standard for the Exchange of Product Model Data, Data Exchange Translators, Drawing Exchange Formats, Initial Graphics Exchange Specification,
Review of use case for the implementation of "Override Folder" option inside the product structure configuration engine of Teamcenter PLM. The parallel driving of multiple, alternative design solutions similar to the morphological matrix principle is easy to handle by the adoption of this option on revision rule definitions. With such techniques the CAD driven early concept phases resp. design phases can be accelerated.
The Module for Pipe Class and Catalogue Management
Independent module for development and management of pipe classes, creation of parameterized 3D components, preparation and integration of manufacturer catalogues, import and export of data plus examination of existing catalogue data to ensure up-to-dateness.
CADISON® Project Engineer is your tool for plant design, Engineering calculations and detailing of your plant by adding all required components (objects) to the project while taking them from the catalogue. Simple Drag & Drop operations are sufficient with completely text based operations without the obligation to have a graphical environment. This approach is called "Conceptual Engineering". The target of CADISON® Project Engineer is to provide the user with data for calculation without large efforts and already at a very early time.
Installation and pipeline planning in the 3D model are in the competence of the 3D Designer. Normally this module is used for access to data from Basic Engineering or P&ID. Efficient assistants are available for installation planning: For instance, isometrics can be automatically generated from the planned pipeline systems.
CADISON® Project Engineer is your tool for plant design, Engineering calculations and detailing of your plant by adding all required components (objects) to the project while taking them from the catalogue. Simple Drag & Drop operations are sufficient with completely text based operations without the obligation to have a graphical environment.
SAP Data Lookup for HD3D Visual Reporting. Routing ERP information, managed inside SAP, into the NX CAD framework to establish HD3D Visual Reporting as supporting dahsboard tool for enabling faster and smarter decisions. Review of the implementation of HD3D Visual Reporting at GEA Farm Technologies GmbH.
Preparation of planning documents for instrumentation, power plants and control but also installation and process measuring and control technology are in the competence of the electric design engineer. The common data base permits at any time the access to information about all trades involved in the project such that planning of electrical engineering can be combined with planning of process engineering.
CAESAR II é uma solução completa que permite uma análise rápida e precisa dos sistemas de tubulações sujeitos a uma ampla variedade de cargas que levam em consideração as condições de peso, de pressão, térmicas, sísmicas e outras condições estáticas e dinâmicas. Ele pode analisar sistemas de tubulações de virtualmente qualquer dimensão ou complexidade.
Para maiores informações:
www.natecnologia.com.br
Product Structure Analysis - Alternative ToolsMatthias Ahrens
A proposal for using network visualization tools, which are used in bio-analytics, social network analytics and ontology representation, for the visualization tasks of complex product structures. To establish a mass customization approach the modularity and variant structures and dependencies habe to be build up accurately in the product structures, managed in the ERP and PLM frameworks. Sometimes it is required to review and visualize such dependencies across multiple domains. Offline network visualization tools like Cytoscape, Protégé and Gephi can be an option to support this data visualization tasks.
Standardization in Graphics, Graphics KERNEL System, Standard for the Exchange of Product Model Data, Data Exchange Translators, Drawing Exchange Formats, Initial Graphics Exchange Specification,
Review of use case for the implementation of "Override Folder" option inside the product structure configuration engine of Teamcenter PLM. The parallel driving of multiple, alternative design solutions similar to the morphological matrix principle is easy to handle by the adoption of this option on revision rule definitions. With such techniques the CAD driven early concept phases resp. design phases can be accelerated.
The Module for Pipe Class and Catalogue Management
Independent module for development and management of pipe classes, creation of parameterized 3D components, preparation and integration of manufacturer catalogues, import and export of data plus examination of existing catalogue data to ensure up-to-dateness.
CADISON® Project Engineer is your tool for plant design, Engineering calculations and detailing of your plant by adding all required components (objects) to the project while taking them from the catalogue. Simple Drag & Drop operations are sufficient with completely text based operations without the obligation to have a graphical environment. This approach is called "Conceptual Engineering". The target of CADISON® Project Engineer is to provide the user with data for calculation without large efforts and already at a very early time.
Installation and pipeline planning in the 3D model are in the competence of the 3D Designer. Normally this module is used for access to data from Basic Engineering or P&ID. Efficient assistants are available for installation planning: For instance, isometrics can be automatically generated from the planned pipeline systems.
CADISON® Project Engineer is your tool for plant design, Engineering calculations and detailing of your plant by adding all required components (objects) to the project while taking them from the catalogue. Simple Drag & Drop operations are sufficient with completely text based operations without the obligation to have a graphical environment.
CADISON® combines the engineering workflow in one system and thus significantly accelerates the plant design processes.
The common object-oriented data model for the different fields of application (tender planning, process engineering, installation planning, pipeline planning, electrical engineering, instrumentation etc.) makes it possible to integrate all planning phases so that time and costs are saved. CADISON® serves to collect valuable information in the tendering phase already so that staff members have the required data available in all later phases of project handling.
The CADISON® P&ID Designer plays a decisive role in design, construction, commissioning and maintenance and has an enormous effect on the complete lifecycle of a plant. In this case the preliminary project engineering will be integrated with Basic and Detail Engineering and 2D layout planning. Apart from the P&I diagrams the P&ID Designer even creates block flow charts and process flow diagrams (PFD).
CADISON® Project Navigator is the module for viewing of project data within the corporate network. Navigator has been designed for staff members normally not involved in the active planning of a plant but afterwards responsible for operation and maintenance of the plant (i.e. mere data consumers).
elecworks for PTC Creo - Mechatronics software - 3D CAD softwareGuillem Fiter
Integrate your electrical schematic projects from elecworks to PTC® Creo®, increase collaboration between mechanical and electrical departments and reduce your time to market.
CADISON celebrates its 15-year journey this year. Right from the beginning, its unique design philosophy & architecture and engineering data-driven solution approach has been a core strength. It allows seamless unification of data, objects and workflows – naturally yielding the ‘Single Version of Truth’ throughout the project life-cycle across various stakeholders of the enterprise, be it different disciplines or sites or suppliers.
Review of Development done in Computerization of Electrical Specifications fo...ijsrd.com
In the past, the process of preparation of Electrical Specification for Transformers was carried out by drafting in AutoCAD and Transformer Design calculations were done manually based on output data obtained from Disintegrated Transformer Design programs. In today's competitive environment, where design cycles have reduced drastically, it becomes imperative to fully computerize the Electrical Specification Document Generation for Transformer Design to speed up the whole design process.
Our satisfied customers reveal with their successes that even you can reach 30% efficiency improvement in your company through the use of CADISON®.
As one of our first customers the company VPT Kompressoren (Story) has the Citrix solution in use. Thus not only work from the home office gets possible but also the simple and cost-efficient integration of external service providers. This method opens totally new chances to overcome short-term staffing shortages without disclosing the company’s data and know-how.
CADISON® combines the engineering workflow in one system and thus significantly accelerates the plant design processes.
The common object-oriented data model for the different fields of application (tender planning, process engineering, installation planning, pipeline planning, electrical engineering, instrumentation etc.) makes it possible to integrate all planning phases so that time and costs are saved. CADISON® serves to collect valuable information in the tendering phase already so that staff members have the required data available in all later phases of project handling.
Increase Your Competitiveness
CADISON® combines the engineering workflow in one system and thus significantly accelerates the plant design processes.The common object oriented data model for the different fields of application (tender planning, process engineering, installation planning, pipeline planning, electrical engineering, instrumentation etc.) makes it possible to integrate all planning phases so that time and costs are saved. CADISON® serves to collect valuable information in the tendering phase already so that staff members have the required data available in all later phases of project handling.
The Module for Pipe Class and Catalogue Management
Independent module for development and management of pipe classes, creation of parameterized 3D components, preparation and integration of manufacturer catalogues, import and export of data plus examination of existing catalogue data to ensure up-to-dateness.
The Module for P&ID Project Environment
The CADISON® P&ID Designer plays a decisive role in design, construction, commissioning and maintenance and has an enormous effect on the complete lifecycle of a plant. In this case the preliminary project engineering will be integrated with Basic and Detail Engineering and 2D layout planning. Apart from the P&I diagrams the P&ID Designer even creates block flow charts and process flow diagrams (PFD).
As a business owner in Delaware, staying on top of your tax obligations is paramount, especially with the annual deadline for Delaware Franchise Tax looming on March 1. One such obligation is the annual Delaware Franchise Tax, which serves as a crucial requirement for maintaining your company’s legal standing within the state. While the prospect of handling tax matters may seem daunting, rest assured that the process can be straightforward with the right guidance. In this comprehensive guide, we’ll walk you through the steps of filing your Delaware Franchise Tax and provide insights to help you navigate the process effectively.
What is the TDS Return Filing Due Date for FY 2024-25.pdfseoforlegalpillers
It is crucial for the taxpayers to understand about the TDS Return Filing Due Date, so that they can fulfill your TDS obligations efficiently. Taxpayers can avoid penalties by sticking to the deadlines and by accurate filing of TDS. Timely filing of TDS will make sure about the availability of tax credits. You can also seek the professional guidance of experts like Legal Pillers for timely filing of the TDS Return.
Memorandum Of Association Constitution of Company.pptseri bangash
www.seribangash.com
A Memorandum of Association (MOA) is a legal document that outlines the fundamental principles and objectives upon which a company operates. It serves as the company's charter or constitution and defines the scope of its activities. Here's a detailed note on the MOA:
Contents of Memorandum of Association:
Name Clause: This clause states the name of the company, which should end with words like "Limited" or "Ltd." for a public limited company and "Private Limited" or "Pvt. Ltd." for a private limited company.
https://seribangash.com/article-of-association-is-legal-doc-of-company/
Registered Office Clause: It specifies the location where the company's registered office is situated. This office is where all official communications and notices are sent.
Objective Clause: This clause delineates the main objectives for which the company is formed. It's important to define these objectives clearly, as the company cannot undertake activities beyond those mentioned in this clause.
www.seribangash.com
Liability Clause: It outlines the extent of liability of the company's members. In the case of companies limited by shares, the liability of members is limited to the amount unpaid on their shares. For companies limited by guarantee, members' liability is limited to the amount they undertake to contribute if the company is wound up.
https://seribangash.com/promotors-is-person-conceived-formation-company/
Capital Clause: This clause specifies the authorized capital of the company, i.e., the maximum amount of share capital the company is authorized to issue. It also mentions the division of this capital into shares and their respective nominal value.
Association Clause: It simply states that the subscribers wish to form a company and agree to become members of it, in accordance with the terms of the MOA.
Importance of Memorandum of Association:
Legal Requirement: The MOA is a legal requirement for the formation of a company. It must be filed with the Registrar of Companies during the incorporation process.
Constitutional Document: It serves as the company's constitutional document, defining its scope, powers, and limitations.
Protection of Members: It protects the interests of the company's members by clearly defining the objectives and limiting their liability.
External Communication: It provides clarity to external parties, such as investors, creditors, and regulatory authorities, regarding the company's objectives and powers.
https://seribangash.com/difference-public-and-private-company-law/
Binding Authority: The company and its members are bound by the provisions of the MOA. Any action taken beyond its scope may be considered ultra vires (beyond the powers) of the company and therefore void.
Amendment of MOA:
While the MOA lays down the company's fundamental principles, it is not entirely immutable. It can be amended, but only under specific circumstances and in compliance with legal procedures. Amendments typically require shareholder
Remote sensing and monitoring are changing the mining industry for the better. These are providing innovative solutions to long-standing challenges. Those related to exploration, extraction, and overall environmental management by mining technology companies Odisha. These technologies make use of satellite imaging, aerial photography and sensors to collect data that might be inaccessible or from hazardous locations. With the use of this technology, mining operations are becoming increasingly efficient. Let us gain more insight into the key aspects associated with remote sensing and monitoring when it comes to mining.
Business Valuation Principles for EntrepreneursBen Wann
This insightful presentation is designed to equip entrepreneurs with the essential knowledge and tools needed to accurately value their businesses. Understanding business valuation is crucial for making informed decisions, whether you're seeking investment, planning to sell, or simply want to gauge your company's worth.
Personal Brand Statement:
As an Army veteran dedicated to lifelong learning, I bring a disciplined, strategic mindset to my pursuits. I am constantly expanding my knowledge to innovate and lead effectively. My journey is driven by a commitment to excellence, and to make a meaningful impact in the world.
Taurus Zodiac Sign_ Personality Traits and Sign Dates.pptxmy Pandit
Explore the world of the Taurus zodiac sign. Learn about their stability, determination, and appreciation for beauty. Discover how Taureans' grounded nature and hardworking mindset define their unique personality.
Attending a job Interview for B1 and B2 Englsih learnersErika906060
It is a sample of an interview for a business english class for pre-intermediate and intermediate english students with emphasis on the speking ability.
Falcon stands out as a top-tier P2P Invoice Discounting platform in India, bridging esteemed blue-chip companies and eager investors. Our goal is to transform the investment landscape in India by establishing a comprehensive destination for borrowers and investors with diverse profiles and needs, all while minimizing risk. What sets Falcon apart is the elimination of intermediaries such as commercial banks and depository institutions, allowing investors to enjoy higher yields.
Accpac to QuickBooks Conversion Navigating the Transition with Online Account...PaulBryant58
This article provides a comprehensive guide on how to
effectively manage the convert Accpac to QuickBooks , with a particular focus on utilizing online accounting services to streamline the process.
RMD24 | Retail media: hoe zet je dit in als je geen AH of Unilever bent? Heid...BBPMedia1
Grote partijen zijn al een tijdje onderweg met retail media. Ondertussen worden in dit domein ook de kansen zichtbaar voor andere spelers in de markt. Maar met die kansen ontstaan ook vragen: Zelf retail media worden of erop adverteren? In welke fase van de funnel past het en hoe integreer je het in een mediaplan? Wat is nu precies het verschil met marketplaces en Programmatic ads? In dit half uur beslechten we de dilemma's en krijg je antwoorden op wanneer het voor jou tijd is om de volgende stap te zetten.
2. CADISON_Module_R10_12_10_EN:Electric-Designer
18.12.2010
15:04 Uhr
Seite 2
CADISON® combines the engineering workflow in one system and thus significantly accelerates the planning processes. All users can see on their workplaces - either graphically or as schematic, as 3D model or text-based in a
tree structure – the same data and objects in each case so that they can be optionally used and modified on all workplaces through simple Drag & Drop.
Data and/or objects are existing once only. Thus errors as a result of redundant data management are excluded. The
sophisticated right system ensures that tasks are handled selectively. Modifications introduced by other users are
immediately made available to all other users. The continuity of the individual work steps in one object-oriented
database forms the core of the CADISON® technology. CADISON® uses the widespread platforms Autodesk AutoCAD
or Microsoft Visio for graphical presentations.
®
CADISON Electric-Designer
The Module for Planning of Electrical Equipment
Use the CADISON® Electric-Designer to combine your plant planning efforts with process control engineering. You
may plan your instrumentation with the same tools – but mainly on the basis of same data and objects available to
all other trades involved in the project.
Same Databasis for all Trades
Use CADISON® Electric-Designer for preparation of all your required planning documents in the fields of power plant
and control engineering, electrical installation technology and control cabinet layout for rapid and comfortable work
on a common database of all trades.
The PLT points (measuring points) defined by the process engineer are further detailed by CADISON® ElectricDesigner with the required instrumentation. The electrical planning engineer bases his work on the specified media
data and connection parameters delivered by the process engineer.
Typicals
Pre-fabricated typicals are used for automatic graphic generation and presentation of instrumentation
in the measuring-point chart. The mechanical connection of measuring point to the process is displayed in the form of “hook-ups”. The planning engineer may use pre-fabricated typicals even in this
case. This collection may be extended by the user
at any time and adapted to its requirements.
PLC Configurator
The PLC configurator supports the work of electric
planning engineer for management of input and output signals. Process flow can be presented in one
function diagram with all signals.
3. CADISON_Module_R10_12_10_EN:Electric-Designer
18.12.2010
15:04 Uhr
Seite 3
Graphical Alignment
The plannned electrical equipment in a circuit diagram can be transmitted to a distributor layout plan through graphical alignment. The power distribution structure gives the planning engineer a survey about the power requirement
in a plant. The planner will be supported with the generation of the integrated calculations for the balance of services.
The power distribution scheme shows the conception of power supply and power distribution. Manufacturer-specific data are transmitted from the material catalogues to the operating equipment.
Collision Recognition
The line routing designed for installation planning may be used in 3D design even directly for recognition of any
potential collisions with other trades.
Manufacturer information on operating equipment includes details of all technical data and dimensions. Data available in this way form the basis for easy and rapid preparation of a control cabinet layout drawn to scale.
Facility Management
The CADISON® Electric-Designer is used both for electrical planning of a plant in classical plant engineering and even
for facility management. For example, this module is used for creation of documentations and for operation management of complex line networks.
Integrated Report Generator
All data prepared by means of
CADISON® Electric-Designer can
be optionally issued by the integrated report generator. For example,
such data might be terminal lists,
cable lists or even selected material evaluations for individual rooms
or construction sections.
All reports can be revised and have
release mechanisms. Said reports
are directly stored within the
CADISON® project. Moreover, all
documents of a project can be
made available even automatically
as PDF documents.
Key Features
· Versatile graphic presentation of equipment for circuit diagrams, control cabinet layout and
3D installation planning
· PLC configuration for management and presentation of input and output signals
· Signal lists – intelligent transmission to PLC programming
· Presentation of process flow as function plan with signals
· Comprehensive symbol and circuitry catalogue for rapid preparation of circuit diagrams and
power distribution schemes
· Symbol and sub-assembly editor for extension of the own catalogue
· Placement supports and Auto-Connect functionalities for installation of components and
creation of connections
· Numbering and identification system according to DIN and KKS
· Independent administration and processing of plant and location marks
· Administration and processing of potential and contact cross-references
· Automatisms for marking of equipment
· Graphical adjustment of equipment contained in the project and all parameters in the project