Digital Electronics & Computer Oraganisation
We Also Provide SYNOPSIS AND PROJECT.
Contact www.kimsharma.co.in for best and lowest cost solution or
Email: amitymbaassignment@gmail.com
Call: 9971223030
9548086042 for call girls in Indira Nagar with room service
Digital Electronics & Computer Oraganisation
1. We Also Provide SYNOPSIS AND PROJECT.
Contact www.kimsharma.co.in for best and lowest cost solution or
Email: amitymbaassignment@gmail.com
Call: 9971223030
Q1. What are flip flop circuits in digital electronics? Discuss race around condition in J-K Flip
Flop.
Q2. What is virtual memory? How address mapping is done in cache memory? Elaborate your
answer with examples.
Q3. Design8:1 Mux for a given function, f=Σ (0, 1,5,7,9, 13)
Q4. How branching takes place in Instruction pipeline. Explain with suitable e xamples
Q5. Write short notes on any three of the following.
a) Microprocessor
b) Modes of data transfer.
c) I/O processor
d) Associative memory
e) Software and Hardware interrupt
Q6. Designa mod-15 counter. Explain the various steps in designing the counter
Q7. What are shift registers? Designa 8 bit shift register with features like PISO, SISO, SIPO and PIPO.
Q8. Compare RISC & CISC architecture.
Case Study
Q1. Give the organization of Micro programmed control unit and explain its operation.
Explain the role of address sequencer in detail. If you convert your control unit to
hardwired unit, what are the changes you will observe?
Q2. Explain in details the block diagram of timing and control unit.
1. Where does a computer add and compare data?
2. Which of the following registers is used to keep track of address of the memory location
where the next instruction is located?
Question 3: A complete microcomputer system consists of
2. Question 4: CPU does not perform the operation
Question 5: Pipelining strategy is called implement
Question 6: A stack is
Question 7: A stack pointer is
Question 8: The branch logic that provides decision making capabilities in the control unit is
known as
Question 9: Interrupts which are initiated by an instruction are
Question 10: A time sharing system imply
11. Processors of all computers, whether micro, mini or mainframe must have
Question 12: What is the control unit's function in the CPU?
Question 13: What is meant by a dedicated computer?
b. which is assigned to one and only one task
Question 14: The most common addressing techiniques employed by a CPU is
a. immediate
b. direct
c. indirect
d. register
e. all of the above
Question 15: Pipeline implement
a. fetch instruction
b. decode instruction
c. fetch operand
3. d. calculate operand
e. execute instruction
f. all of abve
Question 16: Which of the following code is used in present day computing was developed by
IBM corporation?
d. EBCDIC code
Question 17: When a subroutine is called, the address of the instruction following the CALL
instructions stored in/on the
d. stack
Question 18: A microprogram written as string of 0's and 1's is a
d. binary microprogram
Question 19: Memory access in RISC architecture is limited to instructions
c. STA and LDA
20. A collection of 8 bits is called
a. byte
Question 21: An AND gate generates a high output when--
B All of its inputs are high
Question 22: How many address lines are needed to address each memory locations in a 2048 x
4 memory chip?
b. 11
4. 23. A computer program that converts an entire program into machine language at one time is
called a/an
c. compiler
Question 24: In immediate addressing the operand is placed
b. after OP code in the instruction
Question 25: Microprocessor 8085 can address location upto
c. 64K
Question 26: The ALU and control unit of most of the microcomputers are combined and
manufacture on a single silicon chip. What is it called?
b. microprocessor
Question 27: When the RET instruction at the end of subroutine is executed,
c. two data bytes stored in the top two locations of the stack are transferred to the program
counter
Question 28: A microporgram is sequencer perform the operation
e. read and execute
Question 29: Interrupts which are initiated by an I/O drive are
b. external
30. A 32-bit processor has
D 32-bit bus or 32-bit registers
31. Clock speed is measured in—
D Hertz
32. A parity bit is—
B Used to detect errors
33. On-chip cache has—
A Lower access time than RAM
5. 34. The system bus is made up of—
D Data bus, control bus and address bus
35. Modern processor chips may be classified as—
A LSI
36. A nanosecond is—
D 10-9 sec
37. The clock speed of a modern PC is of the order of—
C 400 Mhz
38. An OR gate generates a low output when—
D Power fails
39. The ascending order or a data Hierarchy is—
A bit - bytes - fields - record - file - database
40. A conditional jump instruction--
A Always cause a transfer of control